Text preview for : ElectroVoice ACone.pdf part of ElectroVoice ACone Audio controller. I you can find this file useful, please share with others the sch of Yamaha YST subwoofers and power amplifiers with EEEngine.



Back to : ElectroVoice ACone.pdf | Home

SERVICE MANUAL

ACONE
AUDIO CONTROLLER

IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance (servicing) instructions in the literature accompanying the appliance.

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a damp cloth. Do not block any of the ventilation openings. Install in accordance with the manufactures instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat. Only use attachments/accessories specified by the manufacturer. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

For US and CANADA only:
Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrican for replacement of the absolete outlet.

IMPORTANT SERVICE INSTRUCTIONS
CAUTION: These servicing instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel.
1. Security regulations as stated in the EN 60065 (VDE 0860 / IEC 65) and the CSA E65 - 94 have to be obeyed when servicing the appliance. 2. Use of a mains separator transformer is mandatory during maintenance while the appliance is opened, needs to be operated and is connected to the mains 3. Switch off the power before retrofitting any extensions, changing the mains voltage or the output voltage. 4. The minimum distance between parts carrying mains voltage and any accessible metal piece (metal enclosure), respectively between the mains poles has to be 3 mm and needs to be minded at all times. The minimum distance between parts carrying mains voltage and any switches or breakers that are not connected to the mains (secondary parts) has to be 6 mm and needs to be minded at all times. 5. Replacing special components that are marked in the circuit diagram using the security symbol (Note) is only permissible when using original parts. 6. Altering the circuitry without prior consent or advice is not legitimate. 7. Any work security regulations that are applicable at the location where the appliance is being serviced have to be strictly obeyed. This applies also to any regulations about the work place itself. 8. All instructions concerning the handling of MOS - circuits have to be observed.

Note:

SAFETY COMPONENT (HAS TO BE REPLACED WITH ORIGINAL PART ONLY)

1-2

WARRANTY (Limited)
Electro-Voice products are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as noted in the individual product-line statement(s) below, or in the individual product data sheet or owner's manual, beginning with the date of original purchase. If such malfunction occurs during the specified period, the product will be repaired or replaced (at our option) without charge. The product will be returned to the customer prepaid. Exclusions and Limitations: The Limited Warranty does not apply to: (a) exterior finish or appearance; (b) certain specific items described in the individual product-line statement(s) below, or in the individual product data sheet or owner's manual; © Malfunction resulting from use or operation of the product other than as specified in the product data sheet or owner's manual; (d): malfunction resulting from misuse or abuse of the product; or (e): malfunction occurring at any time after repairs have been made to the product by anyone other than Electro-Voice or any of its authorized service representatives. Obtaining Warranty Service: To obtain warranty service, a customer must deliver the product, prepaid, to Electro-Voice or any of its authorized service representatives together with proof of purchase of the product in the form of a bill of sale or receipted invoice. A list of authorized service representatives is available from Electro-Voice at 600 Cecil Street, Buchanan, MI 49107 (616-695-6831) and/or Electro-Voice West at 9130 Glenoaks Boulevard, Sun Valley, CA 91532 (213-875-1900). Incidental and Consequential Damages Excluded: Product repair or replacement and return to the customer are the only remedies provided to the customer. Electro-Voice shall not be liable for any incidental or consequential damages including, without limitation, injury to persons or property or loss of use. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. Other Rights: This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Electro-Voice Electronics are guaranteed against malfunction due to defects in materials or workmanship for a period of three (3) years from the date of original purchase. Additional details are included in the Uniform Limited Warranty Statement.

Specifications subject to change without notice.

600 Cecil Street, Buchanan, Michigan 49107, Phone 616/695-6831, Fax: 616/695-1304 TELEX/EVI Audio Canada, 705 Progress Ave. Unit 46 Toronto, Onatario, M1H 2x1, Canada , Phone: 800/881-1685, Fax: 877/522-2242 TELEX Communications A.G., Keltenstrasse 11, CH-2563 IPSACH, Switzerland, Phone: 011-41/32-51-6833, Fax: 011-41/32-51-1221 EVI Audio Deutschland GmbH, Hirschberger Ring 45, D-94302, Straubing, Germany, Phone: 011-49/9421-7060, Fax: 011-49/9421-706265 EVI Audio France S.A., Parc de Courcerin-Allee Lech Walesa, Lognes, f-77185 Marne La Vallee, France, Phone: 011-33/1-6480-0090, Fax: 011-33/1-6006-5103 EVI Audio Japan Ltd., 2-5-60 Izumi, Suginami-ku, Tokyo, Japan 168, Phone: 011-81/3-3325-7900, Fax: 011-81/3-3325-7789 EVI Audio (Aust.) Pty., Unit 23, Block C, Slough Business Park, Slough Ave., Silverwater, N.S.W 2141, Australia, Phone 011-61/2-648-3455, Fax: 011-61/2-648-5585 EVI Audio (Hong Kong) Limited, Unit E & F, 21 /F., Luk Hop Industrial Bldg., 8 Luk Hop St., San Po Kong, Kowloon, Hong Kong, Phone: 011-852/351-3628, Fax: 011 -852/351-3329 (357 648 ) 12. 10 .1999

Technische Informationen Architects and engineers specifications

ACONE
AUDIO CONTROLLER

Beschreibung Höchste Anforderungen an Schalldruck, Reichweite und Soundqualität lassen sich in Audioanlagen nur mit aktiven Mehrweglautsprechersystemen realisieren bei denen die unterschiedlichen Frequenzbereiche des Audiosignals jeweils getrennt verstärkt und wiedergegeben werden. Das vergleichsweise beste Preis-Leistungsverhältnis bieten Aktiv 2-Weganlagen mit Subwoofern. Der Bassanteil des Audiosignals wird über die Subwoofer wiedergegeben, der Mittel-Hochtonanteil und die Vocals über hochwertige Fullrangeboxen. Ein wesentlicher Vorteil von Aktiv 2-Weganlagen mit Subwoofern liegt unter anderem darin begründet, daß die Vocals nicht auf verschiedene Lautsprechersysteme aufgeteilt sind. Dadurch ist eine problemlose Justierung des Soundsystems möglich. Komplizierte Einmessarbeiten sind - im Gegensatz zu aktiven 3-Weg oder 4-Wegsystemen- nicht notwendig. Auf kleinen Bühnen oder in kleineren Räumen kann mit einem MonoSubwoofer gearbeitet werden weil die Bässe unter derartigen Bedingungen kaum geortet werden können. Auf größeren Bühnen sind getrennte Subwoofer für beide Seiten unerläßlich, weil sonst zu große Lautstärkeunterschiede zwischen den Bässen und Höhen auf der Bühne und an verschiedenen Zuhörerplätzen auftreten können. Ein zentral angeordneter Mono-Subwoofer kann natürlich vorteilhaft als Ergänzung eingesetzt werden. Der ACONE Controller wurde zum Aufbau höchstwertiger Aktiv-2-Wegsysteme mit Subwoofern entwickelt. Als Leistungsverstärker werden in derartigen Systemen professionelle lineare Leistungsendstufen wie beispielsweise Electro-Voice P1200, P2000, P3000 oder Q44, Q66 eingesetzt. Beim Einsatz von Prozessorendstufen wie beispielsweise Electro-Voice P1250 wird der Endstufenprozessorteil einfach ausgeschaltet. Die Installation und Bedienung des ACONE Controllers ist vollkommen problemlos, der Anwender braucht sich nicht mit der komplexen Materie von Weichenfunktionen und Entzerrern zu beschäftigen. Alle Regler zur Anpassung an die Raumakustik und die Lautsprecherkabinette sind auf der Frontseite zugänglich, die komplizierte elektronische Verknüpfung der Einstellungen wird automatisch intern realisiert. Die neuentwickelte PowerMax12 Weichenfunktion (Patents Pending) nutzt Endstufenleistung und die Übertragungseigenschaften der Boxen optimal. Dadurch werden klanglich erheblich bessere Ergebnisse mit geringerem Aufwand erzielt als mit herkömmlichen Frequenzweichen oder Controllern. Der ACONE Controller eignet sich auch exzellent zum Aufbau von Aktiv 2-Weg Instrumentalanlagen für Keyboards, Bass und Drums und vermeidet durch die PowerMax12 Weichenfunktion den in herkömmlichen aktiven Instrumentalanlagen häufig beklagten ,,lack-of-punchand-definition". Mit dem erstklassigen Dynamikbereich von über 116dB, einem extrem niedrigen Geräuschpegel und herausragendem Preis-Leistungsverhältnis ist der Einsatz des ACONE Controllers auch in kritischen Anwendungen in der Festinstallation eine bevorzugte Alternative zu herkömmlichen Frequenzweichen und Controllern.

Description Meeting the highest requirements of modern audio applications - especially, when it comes to sound pressure level, coverage and sound quality - is only possible when using active multi-component loudspeaker systems which provide the possibility to separately amplify and reproduce the audio signal's individual frequency ranges. Active 2-way installations with additional sub woofer systems probably offer the best price-performance ratio. The low frequency range of the audio signal is reproduced by the sub woofers while high-quality full-range cabinets take care of the Mid/Hi frequencies and vocals. One of the essential advantages when using active 2-way systems with additional sub woofers is the fact that the vocals are not divided between several speaker systems. This, in return, offers more convenience when adjusting the sound system. Unlike than with active 3- or 4-way configurations ­ difficult analyzing and measuring of sound fields is unnecessary. Since locating low-frequency sound is merely impossible, simply using monaural sub woofers is absolutely sufficient for smaller stages or rooms. On wider stages it is indispensable to use individual sub woofer systems for both sides. Otherwise, the level differences between bass and treble would result in audible degradation of the overall sound. Of course, adding a centrally located sub woofer might additionally improve the sound quality. The ACONE Controller has been designed to be used in high-performance installations that employ active 2-way systems plus sub woofers. Applications like these also mostly incorporate professional linear power amplifiers like the Electro-Voice P1200, P2000, P3000 or Q44, Q66. When using processor controlled power amplifiers like the Electro-Voice P1250, the processor section is simply switched off. Installing and operating the ACONE Controllers is easy as can be since the user does not need to know any complex detail about crossover functions and equalization. All controls for matching the sound to different acoustic conditions and loudspeaker systems are located on the front panel. Difficult tasks - like electronic signal routing and settings for instance - are automatically carried out inside the appliance. The newly designed PowerMax12 crossover function (patents pending) optimally utilizes amplifier output power and loudspeaker transmission capacities. Compared to conventional crossovers or controllers, this results in an improved overall sound quality which is achieved with less effort. The ACONE Controller is also most suitable for integration in active 2-way instrument reinforcement applications for keyboards, E-bass and drums. The PowerMax12 crossover function eliminates the often complained about "lack-of-punch-and-definition", like it is common for conventional active musical instrument reinforcement systems. Its excellent dynamic range of more than 116dB, the extremely low noise level and the outstanding price-performance ratio makes the ACONE Controller an advantageous alternative to conventional crossover and controller solutions ­ even in the critical field of permanent installation.

Description Satisfaire aux exigences des applications audio modernes ­ surtout lorsqu'il s'agit de pression sonore, de qualité sonore et de couverture ­ n'est possible qu'en utilisant des systèmes de haut-parleurs actifs multi-voies offrant la possibilité d'amplifier et de reproduire séparément le signal audio de chaque bande de fréquences. Les installations actives à deux voies avec sub-woofers offrent probablement le meilleur rapport performance-prix. Les fréquences basses du signal audio sont reproduites par les sub-woofers alors que des enceintes large bande de qualité se chargent des fréquences médium/hautes et des voix. Un des avantages essentiels offert par l'utilisation des systèmes actifs à deux voies avec des sub-woofers supplémentaires est que les voix ne sont pas réparties sur plusieurs systèmes de haut-parleurs. Ce qui est beaucoup plus pratique pour le réglage de la sonorisation. Contrairement aux configurations actives à 3 ou 4 voies, les mesures et les analyses compliquées des champs sonores ne sont pas nécessaires. Pour les scènes ou les salles de petites dimensions, comme les sons basses fréquences sont pratiquement impossibles à situer, il suffit d'utiliser des sub-woofers mono. Pour les scènes plus grandes il est absolument indispensable d'utiliser un système de sub-woofers séparés pour chaque côté. Sinon, les différences de niveau entre les basses et les aigus provoqueront une dégradation audible du son dans son ensemble. Bien sûr, l'ajout d'un sub-woofer placé au centre améliorera encore la qualité sonore. Le contrôleur ACONE a été conçu pour être utilisé dans des installations performantes employant des systèmes actifs à deux voies avec subwoofers. De telles applications incluent fréquemment des amplificateurs de puissance linéaires professionnels comme les Electro-Voice P1200, P2000, P3000 ou Q44, Q66. Lors de l'utilisation d'amplificateurs de puissance contrôlés par processeur comme le Electro-Voice P1250, la section processeur est tout simplement désactivée. L'installation et le maniement des contrôleurs ACONE est aussi simple que possible, puisque l'utilisateur n'a besoin de connaître les détails complexes des fonctions de Crossover, ou d'égalisation. Tous les contrôles permettant d'adapter le son aux diverses conditions acoustiques et aux divers systèmes de haut-parleurs se trouvent en face avant. Les tâches difficiles ­ comme l'acheminement du signal électronique et les réglages, par exemple - sont automatiquement pris en charge en dehors de l'appareil. La fonction de Crossover, nouvellement conçue, du PowerMax12 (brevet en cours) optimise la puissance de sortie de l'amplificateur en fonction des caractéristiques du hautparleur. Comparé aux Crossovers ou aux contrôleurs conventionnels, le résultat est une qualité sonore globale améliorée qui est obtenue avec moins d'efforts. Le contrôleur ACONE convient également parfaitement lorsqu'il est intégré dans des applications actives à 2 voies pour le renforcement d'instruments, tels les claviers, les basses et les batteries électriques. La fonction Crossover du PowerMax12 élimine le sempiternel "manque-de-punch-et-de-définition", commun aux systèmes actifs conventionnels utiliser pour le renforcement des instruments de musique. Son excellente dynamique, de plus de 116 dB, son niveau de bruit extrêmement bas et son rapport performance-prix très attractif font du contrôleur ACONE une alternative avantageuse aux solutions de Crossover et de contrôleurs conventionnels ­ même dans le domaine critique des installations permanentes.

Technical Specifications ACONE
All level and frequency controls in center position, Lo-EQ and Hi-EQ controls at 0dB, MID-EQ control at -4dB, unless otherwise specified. Note: 0dBu = 0.775V Crossover Mode Frequency, sweepable Filter Type LO-Cut Filter Type Frequency, sweepable Equalization LO-EQ MID-EQ HI-EQ Inputs A, B Type Input Impedance Maximum Level Rated Level Gain Range Parallel Outputs A, B Outputs HI, LO, SUB Type Output Impedance Maximum Level Rated Level Gain Range

2-Way-Stereo + SUB Mono 45Hz ... 160Hz PowerMax12*

12dB/octave 20Hz ... 100Hz

50Hz, Shelving, 0dB ... +12dB 4kHz, Dip, -8dB ... 0dB 15kHz, Lift, 0dB ... +8dB

Active Balanced, XLR-female 20kOhm +20dBu +6dBu - ... + 6dB XLR-male

Active Balanced, XLR-male 75 Ohm + 20dBu + 6dBu - ... + 6dB

Frequency Response, -3dB ref.1kHz, Lo-Cut 20Hz 16Hz ... 150kHz Nominal Gain 0dB Maximum Gain +12dB Dynamic Range, +20dBu, noise A-weighted 117dB THD+N, 20Hz ... 20kHz, +6dBu < 0.02% THD+N, typical, +6dBu 0.003% Crosstalk <-80dB Mute Switch Rejection > 90dB Level Control Attenuation > 80dB Power Requirements, 50Hz....60Hz, voltage selector 100V ... 120V, 220V ... 240V Power Consumption 17 W Dimensions, (WxHxD), mm 483 x 43.6 x 226.5 Weight 3.2 kg Optional, input transformer NRS 90208

*Patents pending

Abmessungen / Dimensions (in mm)

WARRANTY (Limited)
Electro-Voice products are guaranteed against malfunction due to defects in materials or workmanship for a specified period, as noted in the individual product-line statement(s) below, or in the individual product data sheet or owner's manual, beginning with the date of original purchase. If such malfunction occurs during the specified period, the product will be repaired or replaced (at our option) without charge. The product will be returned to the customer prepaid. Exclusions and Limitations: The Limited Warranty does not apply to: (a) exterior finish or appearance; (b) certain specific items described in the individual product-line statement(s) below, or in the individual product data sheet or owner's manual; © Malfunction resulting from use or operation of the product other than as specified in the product data sheet or owner's manual; (d): malfunction resulting from misuse or abuse of the product; or (e): malfunction occurring at any time after repairs have been made to the product by anyone other than Electro-Voice or any of its authorized service representatives. Obtaining Warranty Service: To obtain warranty service, a customer must deliver the product, prepaid, to Electro-Voice or any of its authorized service representatives together with proof of purchase of the product in the form of a bill of sale or receipted invoice. A list of authorized service representatives is available from Electro-Voice at 600 Cecil Street, Buchanan, MI 49107 (616-695-6831) and/or Electro-Voice West at 9130 Glenoaks Boulevard, Sun Valley, CA 91532 (213-875-1900). Incidental and Consequential Damages Excluded: Product repair or replacement and return to the customer are the only remedies provided to the customer. Electro-Voice shall not be liable for any incidental or consequential damages including, without limitation, injury to persons or property or loss of use. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you. Other Rights: This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Electro-Voice Electronics are guaranteed against malfunction due to defects in materials or workmanship for a period of three (3) years from the date of original purchase. Additional details are included in the Uniform Limited Warranty Statement.

Specifications subject to change without notice.

600 Cecil Street, Buchanan, Michigan 49107, Phone 616/695-6831, Fax: 616/695-1304 TELEX/EVI Audio Canada, 705 Progress Ave. Unit 46 Toronto, Onatario, M1H 2x1, Canada , Phone: 800/881-1685, Fax: 877/522-2242 TELEX Communications A.G., Keltenstrasse 11, CH-2563 IPSACH, Switzerland, Phone: 011-41/32-51-6833, Fax: 011-41/32-51-1221 EVI Audio Deutschland GmbH, Hirschberger Ring 45, D-94302, Straubing, Germany, Phone: 011-49/9421-7060, Fax: 011-49/9421-706265 EVI Audio France S.A., Parc de Courcerin-Allee Lech Walesa, Lognes, f-77185 Marne La Vallee, France, Phone: 011-33/1-6480-0090, Fax: 011-33/1-6006-5103 EVI Audio Japan Ltd., 2-5-60 Izumi, Suginami-ku, Tokyo, Japan 168, Phone: 011-81/3-3325-7900, Fax: 011-81/3-3325-7789 EVI Audio (Aust.) Pty., Unit 23, Block C, Slough Business Park, Slough Ave., Silverwater, N.S.W 2141, Australia, Phone 011-61/2-648-3455, Fax: 011-61/2-648-5585 EVI Audio (Hong Kong) Limited, Unit E & F, 21 /F., Luk Hop Industrial Bldg., 8 Luk Hop St., San Po Kong, Kowloon, Hong Kong, Phone: 011-852/351-3628, Fax: 011 -852/351-3329

MEASURED DATA
Function: Analog Controller

ACONE
Issue Date: 27.07. 2000

The measured data apply to the following appliances: Unit Model AC ONE Unit Number 170 090 Mains Voltage 120 or 230 V Mains Frequency 50 - 60 Hz

Testing Conditions: Measuring tolerance: Measuring frequency: Stated level values referred to: Source impedance Line: Load impedance Outputs: INPUT-, EQ-, Output- Control Voltage selector switch Measurement standards: Safety class: Test voltage IEC65: U(F) = Extraneous Voltage U(G) = Noise Voltage U(A) = Interference Voltage X = ± 1.5 dB f = 100Hz / 1 kHz / 10 kHz U = 775 mV ( 0 dBu) R(Q) = 50 R(L) = 100 k Center position 220 V - 240 V ( fuse T100mA ) IEC 268, IHF-A I 3000 Vrms Unweighted, with B = 22Hz ... 22 kHz, effective value (IEC 268) Weighting filter, acc. to CCIR-468-3, quasi peak weighted (IEC 268) A-weighted, dB(A), effective value (IEC 268)

- The printed board assembly 82227 offers measuring points for servicing purposes. CNS 2 1 2 3 4 5 6 7 8 1. Operating Voltages: ACONE ACONE ACONE ACONE Europe Japan U.S.A. Australia Assignment + 15 V GND - 15 V + VSS GND - VSS Relay Time In U(B) = 230V U(B) = 100V U(B) = 120V U(B) = 240V / 50Hz ... 60 Hz / 50Hz ... 60 Hz / 50Hz ... 60 Hz / 50Hz ... 60 Hz

2. Operating Voltage Deviation Range: 3. Power Consumption:

- 10 % .... + 6 % in all modes

Idling 4. Settings/Adjustments:

ACONE Power Consumption 17 W

OUTPUT STAGE SYMMETRY: Symmetrically measure the output voltage --> U1 ( HI-OUT - 1 kHz / LO-OUT - 100 Hz ) Page: 1 / 5

Sum the signals of XLR-Pin 2 and XLR-Pin 3 via high-quality (precise) resistors ( < 10 k / < 0.5 % ) at the input of the measuring device and adjust the resulting signal via trimmers VR 11 / VR 12 / VR 13 / VR 14 / VR 15 to its minimum value --> U2 Unsymmetrical Attenuation = log ( U1 / U2 ) = > 35 dB

5. Function Test POWER-ON DELAY : Feed the signal to Input-Channel A / B and switch the appliance on using the Power-On switch. Approximately 2 seconds after switching the appliance on, the signal is present at the output. MUTE-SWITCH: Feed the signal to Input-Channel A / B. Measure at the outputs and check the function of each Mute-Switch.

6. Level -All level and frequency controls set to their center position, EQ SECTION- all controls set to their "0"position. Input U(E) Output Channel A IN ( 1 kHz ) 0 dBu OUTPUT CH A HI Channel A IN ( 1 kHz ) 0 dBu OUTPUT CH A HI Channel A IN ( 1 kHz ) 0 dBu OUTPUT CH A HI Channel A IN ( 100 Hz ) 0 dBu OUTPUT CH A LO Channel A IN ( 100 Hz ) 0 dBu OUTPUT CH A LO Channel A IN ( 100 Hz ) 0 dBu OUTPUT SUB MONO Channel A IN ( 100 Hz ) 0 dBu OUTPUT SUB MONO Channel B IN ( 1 kHz ) 0 dBu OUTPUT CH B HI Channel B IN ( 1 kHz ) 0 dBu OUTPUT CH B HI Channel B IN ( 1 kHz ) 0 dBu OUTPUT CH B HI Channel B IN ( 100 Hz ) 0 dBu OUTPUT CH B LO Channel B IN ( 100 Hz ) 0 dBu OUTPUT CH B LO Channel B IN ( 100 Hz ) 0 dBu OUTPUT SUB MONO Channel B IN ( 100 Hz ) 0 dBu OUTPUT SUB MONO -Make sure that all level controils are set to their ""-position. U(A) 0 dBu +6 dBu +12 dBu 0 dBu 6 dBu -3.5 dBu +2.5 dBu 0 dBu +6 dBu +12 dBu 0 dBu +6 dBu -3.5 dBu +2.5 dBu Comments HI OUT control at +6 dB INPUT A + HI OUT control at +6 dB LO OUT control at +6 dB SUB OUT control at +6 dB HI OUT control at +6 dB INPUT B + HI OUT control at +6 dB LO OUT control at +6 dB SUB OUT control at +6 dB

7. Amplitudes ­ Non-Linearities - MBW = 80 kHz - All measured values for U(A) = +6 dBu Input Output THD+N at 100Hz < 0.005 % < 0.005 % THD+N at 1kHz < 0.004 % THD+N at 10kHz < 0.015 %

Channel A / B IN ( 1 kHz ) OUTPUTS CH A / B HI Channel A / B IN ( 100 Hz ) OUTPUTS CH A / B LO Channel A / B IN ( 100 Hz ) OUTPUT SUB MONO

Page: 2 / 5

8.1 Frequency Response

15.000 12.000 9.0000 6.0000 3.0000 0.0 -3.000 -6.000 -9.000 -12.00 -15.00 -18.00 -21.00 10

LO-EQ +12dB HI-EQ +8dB +4dB

+6dB

-4dB -8dB MID-EQ

100

1k

10k

100k

8.2 LoCut
15.00 12.00 9.00 6.00 3.00 0.00 -3.00 -6.00 -9.00 -12.00 -15.00 -18.00 -21.00 10 100 1k 10k 100k 20Hz

8.3 X-Over
15.00 12.00 9.00 6.00 3.00 0.00

45Hz 100Hz 160Hz

50Hz 100Hz

-3.00 -6.00 -9.00 -12.00 -15.00 -18.00 -21.00 10 100 1k 10k 100k

9. Border Frequencies - 3 dB @ 1 kHz - All level controls within the signal path set to fully open, EQ SECTION- all controls set to their "0"-position, - LO-CUT set to 20 Hz, X-OVER in center position. ACONE Input Channel A / B IN Channel A / B IN Channel A / B IN Output OUTPUTS CH A / B HI OUTPUTS CH A / B LO OUTPUT SUB MONO f(u) 76 Hz 16 Hz 14 Hz f(o) > 150 kHz 125 Hz 145 Hz

10. Noise Interference - U(F) = extraneous voltage non-weighted with B = 22 Hz ... 22 kHz, effective value (IEC 268-1) - U(G) = noise voltage, frequency-weighting filter according to CCIR-468-3, quasi peak-weighted (IEC 268-1) - U(A) = interference voltage A-weighted, dB(A), effective value (IEC 268-1) - S/N ratio ref. to max. output voltage, A-weighted Page: 3 / 5

- All level and frequency controls set to their center position, EQ SECTION- all controls set to their "0"position Output HI OUT A / B HI OUT A / B HI OUT A / B LO OUT A / B LO OUT A / B LO OUT A / B SUB MONO SUB MONO SUB MONO U(F) dBu -95 -106 -89 -99 -101 -96 -96 -101 -92 U(G) dBu -84 -95 -78 -89 -90 -88 -86 -90 -82 U(A) dBu -97 -108 -91 -102 -103 -101 -99 -103 -95 GAIN S/N-R. Comments dB dB 0 -117 HI OUT STEREO controls down HI OUT STEREO controls up 0 -122 LO OUT STEREO controls down LO OUT STEREO controls up +2.5 -119 SUB OUT MONO controls down SUB OUT MONO controls up

11. Operating Voltages and Service Measuring Points - Voltages measured at the corresponding pin to GND ( mains voltage 230 V ) 82227 CNS 2 1 2 3 4 5 6 7 8 Measured in Idling Condition + 15 V GND - 15 V + VSS GND - VSS Relay Time In + 15 V ± 2.5% - 15 V ± 2.5% + 23 V ± 2% - 23 V ± 2% - 23 after approx. 2 sec. - 11 V Interference and Ripple Voltage U(F)rms < 30 µV < 30 µV < 200 mV < 200 mV

Voltage selector set to 100 - 120 V. Mains voltage adjusted to115 V via regulating transformer. Voltage measurement at CNS 2.4 / 2.6 referred to CNS 2.5 ( ± 23 V ). Afterwards re-set the voltage selector to 220 ­ 240 V!

12. Indicators - The LED starts lighting when the stated input voltages are applied ­ tolerance +/- 2 dB. - All level and frequency controls set to their center position, EQ SECTION- all controls set to their "0"position Indicator SIGNAL INPUT A / B PEAK INPUT A / B PEAK INPUT A / B SIGNAL HI OUTPUT A / B PEAK HI OUTPUT A / B Input Channel A / B In Channel A / B In Channel A / B In Channel A / B In Channel A / B In Comments ( 10kHz ) LO-EQ positioned at +12 dB ( 100Hz ) HI-EQ positioned at +8 dB ( 10kHz ) ( 10kHz ) ( 10kHz ) U(E) -18 dBu +11 dBu +11 dBu -15 dBu +14 dBu Page: 4 / 5

SIGNAL LO OUTPUT A / B PEAK LO OUTPUT A / B SIGNAL SUB OUT MONO PEAK SUB OUT MONO

Channel A / B In Channel A / B In Channel A / B In Channel A / B In

( 100Hz ) ( 100Hz ) ( 100Hz ) Input: CH A+B ( 100Hz ) Input: CH A+B

-17 dBu +14 dBu -19 dBu +11 dBu

13. Initial State (factory-shipped) Unit Type AC ONE Europe Unit-No. Mains Voltage Voltage Selector/Fuse Set to 220V - 240V / 80 mA

170 090 230 V With mains cord 300 425 240 V With mains cord 354 619

AC ONE Australia

Set to 220V - 240V / 80 mA

AC ONE Japan / USA

100 V / 120 V Set to 100V - 120V / 160 mA With US-Kit 357 601 ( Mains cord 346 832, Fuse 302 603, Supplement 357 602, Polyester bag 304 712 )

Page: 5 / 5

Stücklisten - Bill of material
Pos. Nr. Ref. No. Best. Nr. Part No. 170090

Bezeichnung Acone Zubehör

Description

Accessories rubber foot owner's manual power cable Europe Metal work knob push button black 10x6 push button black 12x7 carton carton filler poly bag front panel ACone chassis cover main pcb 82227 cap ceramic 100nF cap ceramic 100nF cap ceramic 330pF cap ceramic 330pF cap ceramic 330pF cap ceramic 330pF cap ceramic 330pF cap ceramic 330pF cap ceramic 330pF cap ceramic 330pF cap ceramic 33pF cap ceramic 33pF cap ceramic 33pF cap ceramic 33pF cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap ceramic 100pF cap ceramic 100pF cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap mylar 56nF cap mylar 56nF cap mylar 470nF cap mylar 470nF

Z 020 Z 040 Z 050

345095 357648 300425

FUSS-GUMMI 12.7X 3.5 BEDIENUNGSANL. AC ONE KABEL-NETZ 2.0 M 10A Mechanische Teile

356348 347430 337059 335228 335229 333375 357643 357957 822278 C0001 C0002 C0003 C0004 C0005 C0006 C0007 C0008 C0009 C0010 C0013 C0014 C0015 C0016 C0017 C0018 C0019 C0020 C0021 C0022 C0023 C0024 C0025 C0026 329021 329021 301543 301543 301543 301543 301543 301543 301543 301543 301558 301558 301558 301558 343532 343532 301530 301530 343532 343532 344109 344109 340988 340988

DK 11 SW/GR/SW C 6FL TK 10X6 SW 2,8 KNOPF-TASTE 12X7 SW 3.3 KRT. DRP 515X365X100 STYROPOR-EINLAGE DRP SCHUTZHÜLLE 500X700X0,05 FB.AC ONE BED DEC.AC ONE BED PCBAR#PX 230 KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-KER KO-EL KO-EL KO-KER KO-KER KO-EL KO-EL KO-FOL KO-FOL KO-FOL KO-FOL 0.10MF 100V 20% 0.10MF 100V 20% 330.0PF 500V 10% 330.0PF 500V 10% 330.0PF 500V 10% 330.0PF 500V 10% 330.0PF 500V 10% 330.0PF 500V 10% 330.0PF 500V 10% 330.0PF 500V 10% 33.0PF 100V 2% 33.0PF 100V 2% 33.0PF 100V 2% 33.0PF 100V 2% 100.000MF 25V 100.000MF 25V 100.0PF 500V 10% 100.0PF 500V 10% 100.000MF 25V 100.000MF 25V 0.056MF 63V 5% 0.056MF 63V 5% 0.470MF 63V 5% 0.470MF 63V 5%

Pos. Nr. Ref. No. C0027 C0028 C0029 C0030 C0031 C0032 C0033 C0034 C0035 C0036 C0037 C0038 C0039 C0040 C0041 C0042 C0043 C0044 C0045 C0046 C0047 C0048 C0053 C0054 C0055 C0056 C0057 C0058 C0059 C0060 C0061 C0062 C0063 C0064 C0065 C0066 C0067 C0068 C0069 C0070 C0071 C0072 C0075 C0076 C0077

Best. Nr. Part No. 343532 343532 342923 342923 344105 344105 342923 342923 344105 344105 301543 301543 337238 337238 337238 337238 344109 344109 340988 340988 343532 343532 343532 343532 343532 301558 301530 301530 343532 343532 343532 301530 343532 343532 343532 343532 327394 327394 300050 300050 301530 301530 326924 326924 342934

Bezeichnung KO-EL KO-EL KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-KER KO-KER KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-FOL KO-EL KO-EL KO-EL KO-EL KO-EL KO-KER KO-KER KO-KER KO-EL KO-EL KO-EL KO-KER KO-EL KO-EL KO-EL KO-EL KO-FOL KO-FOL KO-FOL KO-FOL KO-KER KO-KER KO-FOL KO-FOL KO-FOL 100.000MF 25V 100.000MF 25V 0.220MF 63V 5% 0.220MF 63V 5% 0.027MF 100V 5% 0.027MF 100V 5% 0.220MF 63V 5% 0.220MF 63V 5% 0.027MF 100V 5% 0.027MF 100V 5% 330.0PF 500V 10% 330.0PF 500V 10% 0.680MF 63V 5% 0.680MF 63V 5% 0.680MF 63V 5% 0.680MF 63V 5% 0.056MF 63V 5% 0.056MF 63V 5% 0.470MF 63V 5% 0.470MF 63V 5% 100.000MF 25V 100.000MF 25V 100.000MF 25V 100.000MF 25V 100.000MF 25V 33.0PF 100V 2% 100.0PF 500V 10% 100.0PF 500V 10% 100.000MF 25V 100.000MF 25V 100.000MF 25V 100.0PF 500V 10% 100.000MF 25V 100.000MF 25V 100.000MF 25V 100.000MF 25V 5600.000PF 63V 5% 5600.000PF 63V 5% 330.000PF 100V 5% 330.000PF 100V 5% 100.0PF 500V 10% 100.0PF 500V 10% 2200.000PF 100V 5% 2200.000PF 100V 5% 0.033MF 100V 5%

Description cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap mylar 220nF cap mylar 220nF cap mylar 27nF cap mylar 27nF cap mylar 220nF cap mylar 220nF cap mylar 27nF cap mylar 27nF cap ceramic 330pF cap ceramic 330pF cap mylar 680nF cap mylar 680nF cap mylar 680nF cap mylar 680nF cap mylar 56nF cap mylar 56nF cap mylar 470nF cap mylar 470nF cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap ceramic 33pF cap ceramic 100pF cap ceramic 100pF cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap ceramic 100pF cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap mylar 5600pF cap mylar 5600pF cap mylar 330pF cap mylar 330pF cap ceramic 100pF cap ceramic 100pF cap mylar 2200pF cap mylar 2200pF cap mylar 33nF

Pos. Nr. Ref. No. C0078 C0079 C0080 C0081 C0082 C0083 C0084 C0085 C0086 C0087 C0088 C0089 C0090 C0091 C0092 C0093 C0094 C0095 C0096 C0097 C0098 C0099 C0100 C0101 C0102 C0103 C0104 C0105 C0106 C0107 C0108 C0109 C0110 C0111 C0112 C0113 C0114 C0115 C0116 C0117 C0118 C0119 C0120 C0121 C0122

Best. Nr. Part No. 342934 343532 343532 301558 301558 343533 343533 301543 301543 329021 329021 301558 301558 343533 343533 301543 301543 301558 301558 343533 343533 301543 301543 329021 329021 301558 301558 343533 343533 301543 301543 301558 301558 343533 343533 301543 301543 329021 329021 341714 329021 356661 356661 329021 329021

Bezeichnung KO-FOL 0.033MF 100V 5% KO-EL 100.000MF 25V KO-EL 100.000MF 25V KO-KER 33.0PF 100V 2% KO-KER 33.0PF 100V 2% KO-EL 220.000MF 25V KO-EL 220.000MF 25V KO-KER 330.0PF 500V 10% KO-KER 330.0PF 500V 10% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 33.0PF 100V 2% KO-KER 33.0PF 100V 2% KO-EL 220.000MF 25V KO-EL 220.000MF 25V KO-KER 330.0PF 500V 10% KO-KER 330.0PF 500V 10% KO-KER 33.0PF 100V 2% KO-KER 33.0PF 100V 2% KO-EL 220.000MF 25V KO-EL 220.000MF 25V KO-KER 330.0PF 500V 10% KO-KER 330.0PF 500V 10% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 33.0PF 100V 2% KO-KER 33.0PF 100V 2% KO-EL 220.000MF 25V KO-EL 220.000MF 25V KO-KER 330.0PF 500V 10% KO-KER 330.0PF 500V 10% KO-KER 33.0PF 100V 2% KO-KER 33.0PF 100V 2% KO-EL 220.000MF 25V KO-EL 220.000MF 25V KO-KER 330.0PF 500V 10% KO-KER 330.0PF 500V 10% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-SO 0.10MF 275V 20% K KO-KER 0.10MF 100V 20% KO-EL 2200.000MF 35V KO-EL 2200.000MF 35V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20%

Description cap mylar 33nF cap electrolytic 100uF/25V cap electrolytic 100uF/25V cap ceramic 33pF cap ceramic 33pF cap electrolytic 220uF/25V cap electrolytic 220uF/25V cap ceramic 330pF cap ceramic 330pF cap ceramic 100nF cap ceramic 100nF cap ceramic 33pF cap ceramic 33pF cap electrolytic 220uF/25V cap electrolytic 220uF/25V cap ceramic 330pF cap ceramic 330pF cap ceramic 33pF cap ceramic 33pF cap electrolytic 220uF/25V cap electrolytic 220uF/25V cap ceramic 330pF cap ceramic 330pF cap ceramic 100nF cap ceramic 100nF cap ceramic 33pF cap ceramic 33pF cap electrolytic 220uF/25V cap electrolytic 220uF/25V cap ceramic 330pF cap ceramic 330pF cap ceramic 33pF cap ceramic 33pF cap electrolytic 220uF/25V cap electrolytic 220uF/25V cap ceramic 330pF cap ceramic 330pF cap ceramic 100nF cap ceramic 100nF safety cap 100nF/275V cap ceramic 100nF cap electrolytic 2200uF/35V cap electrolytic 2200uF/35V cap ceramic 100nF cap ceramic 100nF

Pos. Nr. Ref. No. C0123 C0124 C0125 C0126 C0127 C0128 C0129 C0130 C0131 C0132 C0133 C0134 C0135 C0136 C0137 C0138 C0139 C0140 C0141 C0142 C0143 C0144 C0145 C0146 C0147 C0148 C0149 C0150 C0151 C0152 C0153 C0154 C0155 C0156 C0157 C0158 C0159 C0160 C0161 C0162 C0163 C0164 C0165 C0166 C0167

Best. Nr. Part No. 301478 301478 329021 329021 343534 343534 342923 307445 343530 343530 329021 329021 329021 329021 329021 329021 343530 343530 329021 329021 329021 329021 329021 329021 329021 329021 343530 343530 329021 329021 329021 329021 329021 329021 343530 343530 329021 329021 329021 329021 301453 301453 301453 301453 301453

Bezeichnung KO-EL 22.000MF 63V KO-EL 22.000MF 63V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-EL 1000.000MF 16V KO-EL 1000.000MF 16V KO-FOL 0.220MF 63V 5% KO-EL 10.000MF 35V KO-EL 47.000MF 50V KO-EL 47.000MF 50V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-EL 47.000MF 50V KO-EL 47.000MF 50V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-EL 47.000MF 50V KO-EL 47.000MF 50V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-EL 47.000MF 50V KO-EL 47.000MF 50V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-EL 1.000MF 50V KO-EL 1.000MF 50V KO-EL 1.000MF 50V KO-EL 1.000MF 50V KO-EL 1.000MF 50V

Description cap electrolytic 22uF/63V cap electrolytic 22uF/63V cap ceramic 100nF cap ceramic 100nF cap electrolytic 1000uF/16V cap electrolytic 1000uF/16V cap mylar 220nF cap electrolytic 10uF/35V cap electrolytic 47uF/50V cap electrolytic 47uF/50V cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap electrolytic 47uF/50V cap electrolytic 47uF/50V cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap electrolytic 47uF/50V cap electrolytic 47uF/50V cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap electrolytic 47uF/50V cap electrolytic 47uF/50V cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap electrolytic 1uF/50V cap electrolytic 1uF/50V cap electrolytic 1uF/50V cap electrolytic 1uF/50V cap electrolytic 1uF/50V

Pos. Nr. Ref. No. C0168 C0169 C0170 C0171 C0172 C0173 C0174 C0175 C0176 C0177 C0178 C0179 C0180 C0181 C0182 D0001 D0002 D0003 D0004 D0005 D0006 D0007 D0008 D0014 D0015 D0016 D0017 D0018 D0019 D0030 D0031 D0032 D0033 D0034 D0035 D0036 D0037 D0038 D0039 D0040 D0041 D0042 D0043 D0044 D0045

Best. Nr. Part No. 301453 329021 329021 329021 329021 329021 301453 301453 301453 301453 301453 329021 329021 329021 329021 301254 301254 301254 301254 301254 301254 304360 304360 301254 301254 304360 304360 304360 304360 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254

Bezeichnung KO-EL 1.000MF 50V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-EL 1.000MF 50V KO-EL 1.000MF 50V KO-EL 1.000MF 50V KO-EL 1.000MF 50V KO-EL 1.000MF 50V KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% KO-KER 0.10MF 100V 20% DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4007 GEGURTET DIODE 1N 4007 GEGURTET DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4007 GEGURTET DIODE 1N 4007 GEGURTET DIODE 1N 4007 GEGURTET DIODE 1N 4007 GEGURTET DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL

Description cap electrolytic 1uF/50V cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap electrolytic 1uF/50V cap electrolytic 1uF/50V cap electrolytic 1uF/50V cap electrolytic 1uF/50V cap electrolytic 1uF/50V cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF cap ceramic 100nF diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4002 diode 1N 4002 diode 1N 4148 diode 1N 4148 diode 1N 4002 diode 1N 4002 diode 1N 4002 diode 1N 4002 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148

Pos. Nr. Ref. No. D0046 D0047 D0048 D0049 D0050 D0051 D0052 D0053 D0054 D0055 D0056 D0057 D0058 D0059 D0060 D0061 D0062 E0001 E0002 E0003 E0004 E0005 F0001 F0002 F0003 H0001 H0002 I0001 I0002 I0003 I0004 I0005 I0006 I0007 I0008 I0009 I0010 I0011 I0012 I0013 I0014 I0015 I0016 I0018 I0019

Best. Nr. Part No. 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 301254 356745 356745 356745 356745 356745 356996 302579 302579 343457 343457 331340 327197 327197 327197 331340 331340 331340 327197 327197 331340 327197 327197 331340 331340 327197 331340 327197 327197

Bezeichnung DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL DIODE 1N 4148 AXIAL RELAIS M4-24H RELAIS M4-24H RELAIS M4-24H RELAIS M4-24H RELAIS M4-24H SICHER T 80 MA 250V SICHER T 500 MA 250V SICHER T 500 MA 250V DICKS-NETZW. 8PIN 2% DICKS-NETZW. 8PIN 2% IC TL 072 CP 2FACH OP IC NE 5532 P 2FACH OP IC NE 5532 P 2FACH OP IC NE 5532 P 2FACH OP IC TL 072 CP 2FACH OP IC TL 072 CP 2FACH OP IC TL 072 CP 2FACH OP IC NE 5532 P 2FACH OP IC NE 5532 P 2FACH OP IC TL 072 CP 2FACH OP IC NE 5532 P 2FACH OP IC NE 5532 P 2FACH OP IC TL 072 CP 2FACH OP IC TL 072 CP 2FACH OP IC NE 5532 P 2FACH OP IC TL 072 CP 2FACH OP IC NE 5532 P 2FACH OP IC NE 5532 P 2FACH OP

Description diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 diode 1N 4148 relay 24V relay 24V relay 24V relay 24V relay 24V fuse 80mA slow blow fuse 500mA slow blow fuse 500mA slow blow res.network RKL 8A 103J res.network RKL 8A 103J IC TL 072 CP IC NE 5532 N IC NE 5532 N IC NE 5532 N IC TL 072 CP IC TL 072 CP IC TL 072 CP IC NE 5532 N IC NE 5532 N IC TL 072 CP IC NE 5532 N IC NE 5532 N IC TL 072 CP IC TL 072 CP IC NE 5532 N IC TL 072 CP IC NE 5532 N IC NE 5532 N

Pos. Nr. Ref. No. I0020 I0021 I0022 I0023 I0024 I0025 I0026 I0027 I0028 JS001 JS002 JS003 JS004 JS005 JS006 JS007 JS008 JS009 JS010 LED11 LED12 LED13 LED22 LED23 LED24 LED25 LED26 LED27 LED28 LED29 Q0001 Q0002 Q0003 Q0004 Q0005 Q0006 Q0007 R0242 R0243 R0244 R0245 R0246 R0247 R0248 R0249

Best. Nr. Part No. 327197 327197 327197 354929 354199 343502 343502 343502 343502 351816 351816 351815 351815 351816 351816 351816 351816 351816 338835 356749 356749 356749 356746 356746 356746 356746 356746 356746 356746 356843 307150 306928 306928 307150 306928 306928 307150 329215 329215 329215 329215 329215 329215 329215 329215

Bezeichnung IC NE 5532 P 2FACH OP IC NE 5532 P 2FACH OP IC NE 5532 P 2FACH OP IC SPNG.REGL. LM 337 T IC SPNG.REGL. LM 317 T IC LM 2901 N IC LM 2901 N IC LM 2901 N IC LM 2901 N STECKER-FL. XLR 3POL PRINTB STECKER-FL. XLR 3POL PRINTB BUCHSE-FL. XLR 3POL SW BUCHSE-FL. XLR 3POL SW STECKER-FL. XLR 3POL PRINTB STECKER-FL. XLR 3POL PRINTB STECKER-FL. XLR 3POL PRINTB STECKER-FL. XLR 3POL PRINTB STECKER-FL. XLR 3POL PRINTB STECKER-KALTGERÄTE LED RT 3MM LOW CURRENT LED RT 3MM LOW CURRENT LED RT 3MM LOW CURRENT LED RT/GN 3MM LOW CURRENT LED RT/GN 3MM LOW CURRENT LED RT/GN 3MM LOW CURRENT LED RT/GN 3MM LOW CURRENT LED RT/GN 3MM LOW CURRENT LED RT/GN 3MM LOW CURRENT LED RT/GN 3MM LOW CURRENT LED GN 3MM LOW CURRENT TRANS BC 337-25 TO 92 TRANS BC 560 C TRANS BC 560 C TRANS BC 337-25 TO 92 TRANS BC 560 C TRANS BC 560 C TRANS BC 337-25 TO 92 WI-SI 10.00 OHM 0.30W 5% WI-SI 10.00 OHM 0.30W 5% WI-SI 10.00 OHM 0.30W 5% WI-SI 10.00 OHM 0.30W 5% WI-SI 10.00 OHM 0.30W 5% WI-SI 10.00 OHM 0.30W 5% WI-SI 10.00 OHM 0.30W 5% WI-SI 10.00 OHM 0.30W 5%

Description IC NE 5532 N IC NE 5532 N IC NE 5532 N IC LM 337 voltage regulator IC LM 317 voltage regulator IC LM 2901 IC LM 2901 IC LM 2901 IC LM 2901 xlr connector male xlr connector male xlr connector female xlr connector female xlr connector male xlr connector male xlr connector male xlr connector male xlr connector male connector male mains led red led red led red led red/green led red/green led red/green led red/green led red/green led red/green led red/green led green transistor BC 337-25 transistor BC 560 C transistor BC 560 C transistor BC 337-25 transistor BC 560 C transistor BC 560 C transistor BC 337-25 safety resistor 10 ohm safety resistor 10 ohm safety resistor 10 ohm safety resistor 10 ohm safety resistor 10 ohm safety resistor 10 ohm safety resistor 10 ohm safety resistor 10 ohm

Pos. Nr. Ref. No. S0001 S0002 S0004 S0005 S0006 T0001 VR001 VR002 VR003 VR004 VR005 VR006 VR007 VR008 VR009 VR010 VR011 VR012 VR013 VR014 VR015 00005 00010 00015

Best. Nr. Part No. 349114 340434 344038 344038 344037 356744 356751 356751 356750 356752 356752 356750 356751 356750 356750 356750 356753 356753 356753 356753 356753 328390 328391 303576

Bezeichnung SCHALTER-NETZ SCHALTER-SCHIEBE 2XUM SCHALTER-RAST 4XUM SCHALTER-RAST 4XUM SCHALTER-RAST 2XUM NETZTRAFO-RINGKERN 10 VA P-DREH 10KOHM LIN B P-DREH 10KOHM LIN B P-DREH 2X 10KOHM LIN B P-DREH 4X 10KOHM LOG NEG E P-DREH 4X 10KOHM LOG NEG E P-DREH 2X 10KOHM LIN B P-DREH 10KOHM LIN B P-DREH 2X 10KOHM LIN B P-DREH 2X 10KOHM LIN B P-DREH 2X 10KOHM LIN B WI-TRI 5.00 KOHM LIN WI-TRI 5.00 KOHM LIN WI-TRI 5.00 KOHM LIN WI-TRI 5.00 KOHM LIN WI-TRI 5.00 KOHM LIN SICHER-HALTER FAU SICHER-HALTER-KAPPE FEK SICHER-HALTE-FEDER

Description mains switch switch slide switch 4pdt latching switch 4pdt latching switch dpdt latching mains transformer 230V potentiometer 10k lin potentiometer 10k lin potentiometer 2x10k lin potentiometer 4x10k -log potentiometer 4x10k -log potentiometer 2x10k lin potentiometer 10k lin potentiometer 2x10k lin potentiometer 2x10k lin potentiometer 2x10k lin trim pot 5k lin trim pot 5k lin trim pot 5k lin trim pot 5k lin trim pot 5k lin fuse holder fuse holder carrier fuse clip