Text preview for : LE-26S81BX.ZIP part of Samsung LE-26S81BX Samsung LCD TV LE-26S81BX LE-26S81BX.ZIP
Back to : LE-26S81BX.ZIP | Home
3 Alignments and Adjustments
3 Alignments and Adjustments
3-1 Service Instruction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers, do not allow the marker generator to distort
test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard, use an isolation transform.
3-1
3 Alignments and Adjustments
3-2 How to Access Service Mode
3-2-1 Entering Factory Mode
" "
Power OFF INFO MENU MUTE Power ON
- If you have Factory remote - control
PICTURE ON DISPLAY FACTORY
- The buttons are active in the service mode.
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left
Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -, Menu, TV/VIDEO(Enter)
3-2-2 Panel Check
Specially for LE26,32R7**, You have to check Panel Maker Because of different adjustments as follows.
First of all, Check the label rating!
1) Label Rating File
PANEL MAKER
If Panel Mark is "A", Set the factory mode Panel BOM(Bill of material) : BN07-00247A
indicating as follows. Connector between Panel and Power Unit
: BN39-00603M (300mm)
Panel BOM(Bill of material) : BN07-00289A * Option Byte
Connector between Panel and Power Unit 1. Gamma "AMLCD"
: BN39-00603M (300mm) 2. Panel Option "AMLCD_INT"
If Panel Mark is "C" , Set the Factory mode
* Option Byte indicating as follows.
1. Gamma "AUO" Panel BOM(Bill of Material) : BN07-00207A
2. Panel Option "AUO" Connecotor between Panel and Powe Unit :
BN39-00659A(200mm)
If Panel Mark is "S" or not printed. * Option Byte
Set the factory mode indicating as follows. 1. Gamma " CMO "
2. Panel Option " CMO "
Others are same shown below.
3-2
3 Alignments and Adjustments
3-3 Factory Data
1. Calibration
2. Option Table XXXX XXXX
3. W/B
4. W/B Movie
5. MTK8202
6. FBE2 option
7. Sound
8. Sound AMP
9. YC Delay
10. Adjust
11. Bus Stop
12. Password 80 80 80 80
13. Checksum 0000
14. Dynamic Contrast
15. Spread Spectrum
16. Reset
HDCP Write Success..(or Failure..)
T_JSMMPEU-1000 (Main Micom Ver) Month/ Day / Year / Hour/ Min./Sec.
T-BRPMNSAS-1000 (Sub Micom Ver. Only BDX Plus)
Panel On Time(Hour) XXXXX
1. Calibration
1) AV Calibration
2) DTV Calibration
3) PC Calibration
4) HDMI Calibration
2. Option Byte
NO item CMO 32"
1 Panel Inch 32
2 Panel Vender CMO
3 Dimming INTERNAL
4 Gamma Off
5 Auto Power On
6 Hotel Mode Off
7 Shop Mode Off
8 High Devi Off
9 Carrier Mute Off
10 TTX On
11 TTX List Flof
12 TTX Group User OSD
13 TTX ATM Off
14 HDMI Select 2HDMI
15 Volume Table Small
16 Sound Wattage LCD 10W
17 HP Position Side
18 Language English
19 HP Detect Active High
3-3
3 Alignments and Adjustments
3. White Balance
No item RF/AV Component
1 SubBright
2 Roffset
3 Goffset
4 Boffset
5 SubContrast
6 RGain
7 GGain
8 BGain