Text preview for : RC-205.pdf part of Daewoo RC-205 Daewoo RC RC-205 RC-205.pdf
Back to : RC-205.pdf | Home
CONTENTS
1. SPECIFICATION .......................................................................2
2. DIAGRAM ..................................................................................3
1) WIRING DIAGRAM................................................................3
2) CIRCUIT DIAGRAM ..............................................................3
3. CAUSE OF TROUBLE AND COUNTERMEASURE ................4
4. COUNTERMEASURE DETAIL .................................................5
5. EXPLODED VIEW AND PARTS LIST ......................................9
1) BODY ASSEMBLY ................................................................9
2) COVER ASSEMBLY ...........................................................11
3) HOSE LINE ASSEMBLY .....................................................13
4) BRUSH ASSEMBLY............................................................15
1
1. SPECIFICATION
RATING 220V, 50~60Hz
INPUT 1010W
AIR WATT 330W
VACUUM 1,050 mmAq.
AIR FLOW 1.11 m/min.
NOISE 65 dB
DIMENSION (L X H X W) 356 X 221 X 246mm
POWER CORD RETRACTABLE 5m
SUCTION CONTROL ELECTRIC SLIDE
DUST METER MECHANICAL
PARTS KEEPING STAND KEEPING
DUST BAG CAPACITY 2.2 Liter
POWER SWITCH ON HOSE HANDLE
FUSE RATING 250V, 6A
BODY 3.8Kg
WEIGHT
NET 4.9Kg
2-LAYER PAPER BAG
DUST CAVITY
NON-WOVEN FABRIC MAT
FILTER
MOTOR CAVITY NON-WOVEN FABRIC MAT
HOSE CURRENT 1.3m
EXTENTION PIPE PLASTIC 2 EA
BRUSH CLEAN
SPARE PAPER BAG 2 EA
2
2. DIAGRAM
1) WIRING DIAGRAM
SWITCH BK
MOTOR
FUSE
BL
FILTER COIL
BK
RED ORANGE
YL
CORD
P.C.B REEL
YL WH
2) CIRCUIT DIAGRAM
C2 R1
C3
T2 R3
TRIAC R2
T1
Q1 M
220V DIODE
C4
50~60Hz C1
Q2
R5 R6
R4
FUSE
220V, 6A
S/W
3
3. CAUSE OF TROUBLE AND COUNTERMEASURE
TROUBLE CHECK POINT CAUSE COUNTERMEASURE
Motor does not Power cord Break of power cord (at Replace the power cord.
rotate. blade tip or root of plug)
Fuse Fuse cut-out Replace the fuse. (Detail 1)
Terminal in body Deflection or break in Repair. (Detail 2)
connections
Cord reel Deflection of terminal or Repair. (Detail 3)
break in connections
Motor Abrasion of carbon brushes Replace the carbon brushes. (Detail 4)
Break in motor winding Replace the motor.
Hose switch Deflection of terminal Repair.
Connections Break Repair. (solder or use connectors)
PCB assembly Defective TRIAC Replace the PCB assembly.
Motor does not Hose switch Deflection of terminal Repair.
stop even if the
switch is set "OFF". PCB assembly Defective TRIAC Replace the PCB assembly.
Suction power Paper bag Full bag with dust Replace the paper bag. (CP-11)
is low.
Hose, brush, and
pipe Blocked or break Remove the obstacle or replace.
Filter Clogged Clean the filter.
Motor Defective Motor Replace the motor.
Dust is Paper bag and Damaged or torn Replace the paper bag or the filter.
excessively filter
discharged from
exhaust grill
during operation.
Cord can not be Cord reel Break of the spring for Replace the bobbin assembly.
wound up. winding cord. Draw out the cord 40-50 Cm and wind
Power cord Entanglement of cord up again.
Reserved winding Insufficient reserved
winding Add proper reserved winding. (6 turns)
Cord does not Tire Abrasion of the tire Replace the tire.
stop at arbitrary Bobbin Sticking dust on the surface Clean.
position. of the bobbin
4
4. COUNTERMEASURE DETAIL
COUNTERMEASURE COUNTERMEASURE PROCEDURE
1. Replacing a fuse
A B
A B
Projection
A B
Fuse
Groove
A
1. Remove 3 screws (41) of the bottom of the body (1), so the
cover assembly can be separated from the body.
2. Take out the fuse assembly from the body.
3. Rotate B part with pushing in the directions as shown the above
figure.
4. Separate B part from A part, and then replace the fuse (250V,
6A)
5. When assembling, rotate B part in the opposite direction of
separating after inserting the projection of the B part into the
groove of the A part.
*CAUTION
Take care not to damage the internal wires on assembling.
5
COUNTERMEASURE COUNTERMEASURE PROCEDURE
2. Repairing the terminal
in the body
4 2 Frame 1 Body
Groove for carrying 3 Terminal
Frame supporter
Standard shape
Groove
1. After removing the screw (4), pull out the frame in the directions
as shown the above figure from the body.
2. Check the terminals (3).
-They are bent or deflected other than standard shape.