Text preview for : Ñõåìà DP-29F.PDF part of DENON Ñõåìà DP-29F DENON LP Turntable LP Turntable Denon - DP-29F Ñõåìà DP-29F.PDF
Back to : Ñõåìà DP-29F.PDF | Home
For U.S.A., Canada
& Europe model
Hi-Fi Full Automatic
Turntable system
MODEL DP-29F
FULL AUTOMATIC TURNTABLE SYSTEM
(with MM Cartridge)
SPEED
30
SIZE
45 33
17
SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.
Some illustrations using in this service manual are slightly different from the actual set.
X0135 NC 0203
ASSEMBLY
1. Remove the main unit with the packing from
the box and take off the packing.
2. Set the 45-rpm adaptor on the main unit as Turntable sheet
shown in the diagram.
3. Insert the turntable onto the center spindle.
4. Set the belt on the driving pulley. (The belt is Turntable
wound on the turntable.) Equalizer Amplifier switch
5. Set the turntable sheet on the turntable.
45-rpm adaptor
6. Remove the tie securing the tonearm. Tonearm fixing tie
NOTE: Center spindle
The turntable will not function if this tie is not
removed.
7.
8. Equalizer Amplifier switch
9. This unit has built-in RIAA When the unit is connected When the unit is connected
10. equalizer amplifier,so it can to the PHONO(MM) jacks: to the AUX jacks, etc:
11. be connected to an amplifier
12. without PHONO(turntable) L
L
13. input jack. According to the
14. amplifier, set the EQUALIZER
R R
15. PHONO AUX
AMPLIFIER SWITCH. ON OFF ON OFF
16.
Setting the belt
Tape
Grasp both sides of the tape and set the belt on the
motor pulley. Once the belt is set properly, remove Driving roller
the tape.
Set the belt on the motor pulley properly as shown Belt
in the diagram.
Turntable
CONNECTIONS
1. Connect the left (white) and right (red) output cords respectively to your amplifier's PHONO jacks
etc .
2. Connect the ground wire to the amplifier's signal ground terminal.
3. Plug the power cord into a wall outlet. (Or if the amplifier has power outlets, plug it in there, but
before doing so, read the amplifier's manual and check that the capacity is sufficient.)
INPUTS PB
CD DVD/AUX AUX-2 TAPE MD
1 2 SYSTEM
L CONNECTOR
SIGNAL R L
GND
TUNER PHONO TAPE MD
L
R
R
REC SPEAKER SYSTEM
SPEAKER IMPEDANCE
4 16
Ground wire Red White
Output cord
2
PART NAMES AND FUNCTIONS
1 2 3 4
14 13 12 11 10 9 8 7 6 5
1 Dust cover 10 Tone arm rest
Holds the tone arm.
2 45 rpm adaptor and holder
11 Platter
3 Dust cover hinge
12 Spindle
4 Equalizer amplifier switch
13 Rubber mat
5 Finger lever
Place on the turntable.
6 Size Select Lever
14 SPEED Select Button
Set according to the size of the record.
Set according to the record speed.
7 STOP Button For 33 1/3 rpm: