Text preview for : Carrozzeria.pdf part of NISSAN Almera Tino Body e Trim (pag. 68) - Manual Transaxale (pag. 102)
Back to : Almera Tino____03___.part | Home
BODY & TRIM SECTION
GI MA EM LC EC
BT
CONTENTS
PRECAUTIONS ...............................................................3 Service Notice..............................................................3 Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TENSIONER...............3 CLIP AND FASTENER....................................................4 Description ...................................................................4 CHASSIS AND BODY MAINTENANCE .........................6 Checking Body Corrosion............................................6 BODY FRONT END.........................................................7 Removal and Installation .............................................7 FRONT BUMPER ASSEMBLY ....................................7 BODY REAR END AND OPENER................................10 Removal and Installation ...........................................10 REAR BUMPER ASSEMBLY ....................................10 DOOR.............................................................................13 Adjustment .................................................................13 STRIKER ADJUSTMENT ..........................................13 Front Door Glass .......................................................14 FRONT DOOR GLASS AND REGULATOR ................14 Front Door Limit Switch Reset (Driver side only)......15 RESET CONDITIONS ..............................................15 RESET PROCEDURES ............................................15 Rear Door Glass........................................................16 REAR DOOR GLASS AND REGULATOR ..................16 Front Door Lock.........................................................18 OUTSIDE HANDLE ROD ADJUSTMENT ...................18 REMOVAL ...............................................................18 Rear Door Lock .........................................................20 OUTSIDE HANDLE ROD ADJUSTMENT ...................20 REMOVAL ...............................................................21 INSTRUMENT PANEL ASSEMBLY .............................22 Removal and Installation ...........................................22 SIDE AND FLOOR TRIM...............................................27 Removal and Installation ...........................................27 LUGGAGE ROOM TRIM ...............................................30 Removal and Installation ...........................................30 DOOR TRIM ...................................................................31 Removal and Installation ...........................................31 ROOF TRIM ...................................................................34 Removal and Installation ...........................................34 BACK DOOR TRIM .......................................................36 Removal and Installation ...........................................36 EXTERIOR .....................................................................37 Removal and Installation ...........................................37 FRONT SEAT ................................................................45 Removal and Installation ...........................................45 MANUAL SEAT........................................................46 Heated Seat...............................................................47 Active Head Restraint................................................47 OPERATION OUTLINE ............................................47 REAR SEAT...................................................................48 Removal and Installation ...........................................48 REAR OUTSIDE SEAT.............................................48 REAR CENTER SEAT ..............................................49 SUNROOF......................................................................50 Adjustment .................................................................50 Removal.....................................................................50 Trouble Diagnoses.....................................................54 DIAGNOSTIC TABLE................................................54 WIND DEFLECTOR (WHERE FITTED) ......................54 ADJUSTMENT .........................................................55 DRAIN HOSES ........................................................56 WEATHERSTRIP .....................................................56 LINK AND WIRE ASSEMBLY ....................................57 WINDSHIELD AND WINDOWS ....................................58 Removal and Installation ...........................................58 REMOVAL ...............................................................58 INSTALLATION........................................................58 WINDSHIELD ..........................................................59 SIDE WINDOW ........................................................60 BACK DOOR WINDOW ............................................61 DOOR MIRROR .............................................................62 Removal and Installation ...........................................62 REAR VIEW MIRROR ...................................................63 Removal and Installation ...........................................63 REMOVAL ...............................................................63 INSTALLATION........................................................63 BODY (ALIGNMENT) ....................................................64 Alignment ...................................................................64 ENGINE COMPARTMENT ........................................65
FE CL MT AT AX SU BR ST RS
HA SC EL IDX
CONTENTS
UNDERBODY ..........................................................67
(Cont'd)
BT-2
PRECAUTIONS
Service Notice
Service Notice
¼ ¼ ¼ ¼ ¼
NLBT0001
When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent scratches. Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or damage them. Apply sealing compound where necessary when installing parts. When applying sealing compound, be careful that the sealing compound does not protrude from parts. When replacing any metal parts (for example body outer panel, members, etc.), be sure to take rust prevention measures.
GI MA EM LC
Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
NLBT0002
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER" used along with a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. The SRS system composition which is available to NISSAN MODEL V10 is as follows (The composition varies according to the destination and optional equipment.): ¼ For a frontal collision The Supplemental Restraint System consists of driver air bag module (located in the center of the steering wheel), front passenger air bag module (located on the instrument panel on passenger side), front seat belt pre-tensioners, a diagnosis sensor unit, warning lamp, wiring harness and spiral cable. ¼ For a side collision The Supplemental Restraint System consists of front side air bag module (located in the outer side of front seat), side air bag (satellite) sensor, diagnosis sensor unit (one of components of air bags for a frontal collision), wiring harness, warning lamp (one of components of air bags for a frontal collision). Information necessary to service the system safely is included in the RS section of this Service Manual. WARNING: ¼ To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance should be performed by an authorized NISSAN dealer. ¼ Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the RS section. ¼ Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. Spiral cable and wiring harnesses covered with yellow insulation tape either just before the harness connectors or for the complete harness are related to the SRS.
EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
BT-3
CLIP AND FASTENER
Description
Description
¼ ¼ Clips and fasteners in BT section correspond to the following numbers and symbols. Replace any clips and/or fasteners which are damaged during removal or installation.
Symbol No. Shapes Removal & Installation
NLBT0003
C101
SBF302H SBF367BA
C103
SBT095 SBF423H
C203
SBF258G SBF708E
C205
MBT080A
SBF638CA
C206
MBF519B MBF520B
BT-4
CLIP AND FASTENER
Description (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
SIIA0316E
BT-5
CHASSIS AND BODY MAINTENANCE
Checking Body Corrosion
Checking Body Corrosion
NLBT0033
Visually check the body sheet metal panel for corrosion, paint damage (scratches, chipping, rubbing, etc.) or damage to the anti-corrosion materials. In particular, check the following locations. Hemmed portion Hood front end, door lower end, trunk lid rear end, etc. Panel joint Side sill of rear fender and center pillar, rear wheel housing of rear fender, around strut tower in engine compartment, etc. Panel edge Trunk lid opening, sunroof opening, fender wheelarch flange, fuel filler lid flange, around holes in panel, etc. Parts contact Waist molding, windshield molding, bumper, etc. Protectors Damage or condition of mudguard, fender protector, chipping protector, etc. Anti-corrosion materials Damage or separation of anti-corrosion materials under the body. Drain holes Condition of drain holes at door and side sill. When repairing corroded areas, refer to the Corrosion Repair Manual.
BT-6
BODY FRONT END
Removal and Installation
Removal and Installation
¼ ¼ ¼ ¼ ¼ 1. 2. 3. 4. 5.
NLBT0004
When removing or installing hood, place a cloth or other padding on hood. This prevents vehicle body from being scratched. Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it. Hood adjustment: Adjust at hinge portion. Hood lock adjustment: After adjusting, check hood lock control operation. Apply a coat of grease to hood locks engaging mechanism. Hood opener: Do not attempt to bend cable forcibly. Doing so increases effort required to unlock hood.
NLBT0004S01
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
FRONT BUMPER ASSEMBLY
Remove clips securing front grille, then remove front grille. Remove clips and screws securing left and right sides of fender protectors. Remove clips and screws securing left and right sides of fender protectors in wheelhouse. Remove screws securing left and right front fenders to bumper fascia. Remove bolts securing radiator core support lower to bumper fascia and remove clips securing lower side of bumper fascia. 6. Remove clips securing radiator core support upper to bumper fascia. 7. Extract bumper fascia assembly. Then disconnect harness connectors. (Models with fog lamp assembly) 8. Remove bolts securing left and right side of bumper lower bracket. 9. Remove energy absorber. 10. Remove bolts and hooks securing the headlamp assembly, then disconnect harness connectors. In case of headlamp bracket breakage, repair of the headlamp unit is possible by means of the bracket repair kit. Headlamp bracket repair kit part number: KE260BU125 (RH side) KE260BU025 (LH side) 11. Remove nuts securing bumper reinforcement to left and right bumper stays. 12. Extract bumper reinforcement. 13. Remove bolts securing bumper upper retainer, then remove bumper upper retainer. 14. Remove bolts securing bumper stays, then remove the bumper stays. Fog lamp assembly (Models with fog lamp assembly) 15. Remove screw securing fog lamp assembly. 16. Extract fog lamp assembly.
HA SC EL IDX
NBT137
BT-7
BODY FRONT END
Removal and Installation (Cont'd)
NBT138
BT-8
BODY FRONT END
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
YBT113
BT-9
BODY REAR END AND OPENER
Removal and Installation
Removal and Installation
¼ ¼ ¼ ¼ ¼ 1. 2. 3. 4. 5. 6. 7. 8.
NLBT0034
When removing or installing back door, place a cloth or other padding on back door. This prevents vehicle body from being scratched. Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it. Back door adjustment: Adjust at hinge-back door portion for proper back door fit. Back door lock system adjustment: Adjust striker so that it is in the center of the lock. After adjustment, check back door lock operation. After installation, make sure that back door and fuel filler lid open smoothly.
NLBT0034S01
REAR BUMPER ASSEMBLY
Remove clips securing left and right chipping protectors. Remove screws securing left and right rear fenders to bumper fascia. Remove clips securing bumper fascia assembly. Remove bolts securing left and right rear body to bumper fascia. Open the bumper fascia side outward to disengage from side clips. Extract bumper fascia assembly. Remove nuts securing bumper reinforcement to left and right bumper stays. Remove bolts securing bumper stays, then remove the bumper stays.
NBT168
BT-10
BODY REAR END AND OPENER
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
YBT103
BT-11
BODY REAR END AND OPENER
Removal and Installation (Cont'd)
YBT104
BT-12
DOOR
Adjustment
Adjustment
NLBT0006
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
NBT085
HA SC EL IDX
STRIKER ADJUSTMENT
NLBT0006S01
Adjust striker so that it is parallel with advancing direction of door lock.
SBT772-B
BT-13
DOOR
Front Door Glass
Front Door Glass
¼ ¼
=NLBT0007
Make sure that door glass is positioned in glass run groove. Make sure that there is no abnormality when door glass is raised or lowered.
NLBT0007S01
FRONT DOOR GLASS AND REGULATOR
NBT086
¼ ¼
For removal of front door finisher, refer to "DOOR TRIM", BT-31. Remove sealing screen.
1. 2.
Using power window main switch, raise or lower door glass until carrier plate securing bolts are visible. Remove bolts securing carrier plate.
NBT087
BT-14
DOOR
Front Door Glass (Cont'd)
3.
Hold door glass with both hands. While raising rear end of door glass, remove door glass from sash and away from outside the door.
GI MA EM
NBT088
LC
4. 5. Disconnect regulator assembly connector. Remove bolts securing regulator assembly and guide rail, then remove regulator assembly and guide rail.
EC FE CL
NBT089
MT
Inspection
NLBT0007S0101
Check regulator assembly for the following parts. Replace faulty parts with new ones. ¼ Wire for wear ¼ Regulator for deformation ¼ Sliding parts for lubrication
AT AX SU BR
NBT090
Front Door Limit Switch Reset (Driver side only)
RESET CONDITIONS
ST
NLBT0008 NLBT0008S01
After each of the following operations are performed, reset the limit switch (with built-in motor). ¼ Regulator removal and installation ¼ Removal of motor from regulator ¼ Operation of regulator as a single unit ¼ Door glass removal and installation ¼ Glass run removal and installation
RS
HA SC EL IDX
RESET PROCEDURES
NLBT0008S02
NBT135
After installing parts, proceed as follows: 1. Close the door window completely. 2. Press the reset switch and open the door window completely. 3. Release the reset switch. After making sure the reset switch has returned to the original position, close the door window completely. 4. The limit switch is now reset. CAUTION: Be sure to manually open or close the door window. (Do not use the automatic open-close procedures.)
BT-15
DOOR
Rear Door Glass
Rear Door Glass
¼ ¼
NLBT0009
Make sure that door glass is positioned in glass run groove. Make sure that there is no abnormality when door glass is raised or lowered.
NLBT0009S01
REAR DOOR GLASS AND REGULATOR
NBT092
¼ ¼ ¼
For removal of rear door finisher, refer to "DOOR TRIM", BT-31. For removal of door outside molding, refer to "EXTERIOR", BT-37. Remove sealing screen.
1. 2.
Using power window main switch, raise or lower door glass until carrier plate securing bolts are visible. Remove bolts securing main channel.
NBT093
BT-16
DOOR
Rear Door Glass (Cont'd)
3.
Remove corner inner cover.
GI MA EM
YBT114
LC
4. Remove nut securing lower sash rear.
EC FE CL
YBT105
MT
5. 6. Remove bolt securing under of lower sash rear. Remove door glass from glass run and away from outside the door.
AT AX SU BR
NBT097
7. 8.
Disconnect regulator assembly connector. Remove bolts securing regulator assembly, then remove regulator assembly.
ST RS
HA
NBT094
Inspection
NLBT0009S0101
SC EL IDX
Check regulator assembly for the following parts. Replace faulty parts with new ones. ¼ Wire for wear ¼ Regulator for deformation ¼ Sliding parts for lubrication
NBT136
BT-17
DOOR
Front Door Lock
Front Door Lock
NLBT0010
NBT098
¼ ¼
For removal of front door finisher, refer to "DOOR TRIM", BT-31. Remove sealing screen.
OUTSIDE HANDLE ROD ADJUSTMENT
NLBT0010S02
Rotate rod holder so that rod-to-holder clearance is adjusted as shown in the figure at left. CAUTION: Make sure that rod-to-holder clearance is not "0" mm (0 in), and that rod is not held pressed.
SBT978
REMOVAL
¼ ¼ ¼ 1.
NLBT0010S03
For removal of front door finisher, refer to "DOOR TRIM", BT-31. Remove sealing screen. For removal of front door glass, refer to "Front Door Glass", BT-14. Remove lower rear sash (unitized with glass run) securing bolts. Remove lower rear sash from door panel and away from door lock.
NBT099
BT-18
DOOR
Front Door Lock (Cont'd)
2. 3. 4. 5. 6. 7.
Remove inside handle escutcheon A. Remove screw securing inside handle. Detach bell crank at lock knob joining area. Detach inside handle rod on the door lock assembly side. Slide inside handle backward and remove inside handle. Remove rod from inside handle.
GI MA EM
NBT100
LC
8. Detach key lock rod and outside handle rod at joining area (on the outside handle side). 9. Disconnect door lock actuator connector. 10. Remove screws securing door lock assembly, then remove door lock assembly. 11. Remove bolts securing outside handle, then remove outside handle assembly.
EC FE CL
NBT101
MT AT AX SU BR ST RS
HA SC EL IDX
BT-19
DOOR
Rear Door Lock
Rear Door Lock
=NLBT0011
YBT106
¼ ¼
For removal of rear door finisher, refer to "DOOR TRIM", BT-31. Remove sealing screen.
NLBT0011S01
OUTSIDE HANDLE ROD ADJUSTMENT
Rotate rod holder so that rod-to-holder clearance is adjusted as shown in the figure at left. CAUTION: Make sure that rod-to-holder clearance is not "0" mm (0 in), and that rod is not held pressed.
SBT978
BT-20
DOOR
Rear Door Lock (Cont'd)
REMOVAL
¼ ¼ ¼ 1. 2. 3.
SBT983
=NLBT0011S02
For removal of rear door finisher, refer to "DOOR TRIM", BT-31. Remove sealing screen. Set the door glass in the full-close position. Remove inside handle escutcheon A. Remove screw securing inside handle. Detach inside handle rod on the door lock assembly side.
GI MA EM LC
Detach lock knob rod (on the door lock assembly side). Using a flat-bladed screwdriver, expand rod holder. Remove rod from rod holder. 6. Slide inside handle backward and remove inside handle. 7. Remove rod from inside handle. 8. Disconnect door lock actuator connector. 9. Remove screws securing door lock assembly, then remove door lock assembly. 10. Remove bolts securing outside handle, then remove outside handle.
NBT103
4. 5.
EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
BT-21
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
Removal and Installation
NLBT0012
CAUTION: ¼ Disconnect ground terminal from battery in advance. ¼ Disconnect air bag system line in advance. ¼ Never tamper with or force air bag lid open, as this may adversely affect air bag performance. ¼ Be careful not to scratch pad and other parts.
YBT111
*1
RS-24
*2
BT-27
*3
RS-26
BT-22
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST
YBT112
RS
*2 BT-27 *3 RS-26
HA SC EL IDX
BT-23
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
YBT107
BT-24
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
YBT108
BT-25
INSTRUMENT PANEL ASSEMBLY
Removal and Installation (Cont'd)
YBT109
BT-26
SIDE AND FLOOR TRIM
Removal and Installation
Removal and Installation
NLBT0013
CAUTION: ¼ Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes. 1. Remove front and rear seats. Refer to "FRONT SEAT" and "REAR SEAT" for details, BT-45 and BT-48. 2. Remove front and rear seat belts. Refer to RS-5 and RS-7, "Front Seat Belt" and "Rear Seat Belt" for details. 3. Remove carpet rear finish, front seat mounting cover and rear seat mounting cover. Refer to "LUGGAGE ROOM TRIM" for details, BT-30. 4. Remove front and rear outer kicking plates. 5. Remove front and rear inner kicking plates. 6. Remove dash side finishers. 7. Remove front and rear body side welts. 8. Remove front pillar garnishes. 9. Remove center pillar lower garnishes. 10. Remove center pillar upper garnishes. 11. Remove front and rear room carpet. 12. Remove rear pillar garnish. 13. Remove rear parcel shelf side finish. 14. Remove luggage room carpet. 15. Remove luggage room rear plate. 16. Remove luggage room rear side plate. 17. Remove luggage room rear side lower finish.
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
BT-27
SIDE AND FLOOR TRIM
Removal and Installation (Cont'd)
NBT107
BT-28
SIDE AND FLOOR TRIM
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT
NBT108
AX SU BR ST RS
HA SC EL IDX
BT-29
LUGGAGE ROOM TRIM
Removal and Installation
Removal and Installation
NLBT0016
NBT181
BT-30
DOOR TRIM
Removal and Installation
Removal and Installation
NLBT0014
Front door finisher 1. Open the window. 2. Remove inside handle escutcheon. 3. Remove screw securing pull handle. 4. Remove screw securing door finisher. 5. Remove clips securing front door finisher. 6. Lift out front door finisher. 7. Remove power window switch by pushing from backside, then disconnect the connectors. Rear door finisher 8. Remove inside handle escutcheon. 9. Remove screw securing power window switch finisher, then disconnect the connector. (Power window model) 10. Remove screw securing pull handle. (Manual window model) 11. Remove window regulator handle. (Manual window model) 12. Remove clips securing rear door finisher. 13. Lift out rear door finisher.
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
BT-31
DOOR TRIM
Removal and Installation (Cont'd)
NBT173
BT-32
DOOR TRIM
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT174
BT-33
ROOF TRIM
Removal and Installation
Removal and Installation
NLBT0015
1. Remove rear seat. 2. Remove shoulder anchor bolts. Refer to RS-5, "Front Seat Belt" for details. 3. Remove front pillar garnishes, center pillar upper garnishes, center pillar lower garnishes and rear pillar garnishes. Refer to "SIDE AND FLOOR TRIM" for details, BT-27. 4. Push back the front seat back. 5. Remove sunroof switch, then disconnect connectors. (Model with sunroof) 6. Remove front personal light then disconnect connector (Model without sunroof) 7. Remove sunroof welt. (Model with sunroof) 8. Remove interior lamp assembly, then disconnect connectors. 9. Remove sun visors. 10. Remove assist grips. 11. Remove clips securing headliner, then remove headliner from vehicle through back door side.
NBT113
BT-34
ROOF TRIM
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT114
BT-35
BACK DOOR TRIM
Removal and Installation
Removal and Installation
1. 2. 3. 4. Remove Remove Remove Remove back door upper finisher. high-mounted stop lamp. back door side finisher. back door finisher.
NLBT0035
NBT115
BT-36
EXTERIOR
Removal and Installation
Removal and Installation
NLBT0017
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT175
BT-37
EXTERIOR
Removal and Installation (Cont'd)
NBT176
BT-38
EXTERIOR
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT119
BT-39
EXTERIOR
Removal and Installation (Cont'd)
NBT120
BT-40
EXTERIOR
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT121
BT-41
EXTERIOR
Removal and Installation (Cont'd)
NBT122
BT-42
EXTERIOR
Removal and Installation (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT123
BT-43
EXTERIOR
Removal and Installation (Cont'd)
NBT125
BT-44
FRONT SEAT
Removal and Installation
Removal and Installation
¼ When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage. CAUTION: ¼ Before removing the front seat, turn the ignition switch off, disconnect both battery cables and wait at least 3 minutes (models with side airbag). ¼ Do not drop, tilt, or bump the side air bag module installed in the seat. Always handle it with care. ¼ Disconnect the side air bag harness connector and heated seat harness connector from under the seat before removing the seat. ¼ Disconnect the side air bag harness connector before removing the seat back. Refer to RS-26, "Front Side Air Bag Module" for details.
NLBT0018
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
BT-45
FRONT SEAT
Removal and Installation (Cont'd)
MANUAL SEAT
NLBT0018S07
NBT177
BT-46
FRONT SEAT
Heated Seat
Heated Seat
5 For Wiring Diagram, refer to EL-250, "HEATED SEAT" for details.
NLBT0036
GI MA EM LC
Active Head Restraint
NLBT0032
The active head restraint system is designed so that the headrest instantaneously moves towards the front upper direction by utilizing the force at the seatback during a rear-end collision. As a result, the occupant's head is protected from being overextended, reducing the chance for neck injury as much as possible. Seat with active head restraint have the labels shown in figures at left.
SBT014A
EC FE CL MT
OPERATION OUTLINE
NLBT0032S01
When the seatback receives a sharp backward force during a rearend collision, the input plate moves with the link rotating center as a pivot. The headrest will then move towards the front upper direction with the center of the sliding roller as a pivot. As the backward force on the seat back is eliminated, spring tension returns the headrest to its original position.
AT AX SU BR
SBT888
ST RS
HA SC EL IDX
BT-47
REAR SEAT
Removal and Installation
Removal and Installation
REAR OUTSIDE SEAT
NLBT0019 NLBT0019S02
NBT178
BT-48
REAR SEAT
Removal and Installation (Cont'd)
REAR CENTER SEAT
NLBT0019S03
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
YBT110
BT-49
SUNROOF
Adjustment
Adjustment
NLBT0020
Install motor & limit SW assembly and sunroof rail assembly in the following sequence: 1. Arrange equal lengths of link and wire assemblies on both sides of sunroof opening. 2. Connect sunroof connector to sunroof switch and positive (+) power supply. 3. Set lid assembly to fully closed position by operating OPEN switch and TILT switch. 4. Fit outer side of lid assembly to the surface of roof on body outer panel. 5. Remove motor, and keep OPEN switch pressed until motor pinion gear reaches the end of its rotating range. 6. Install motor. 7. Check that motor drive gear fits properly in wires. 8. Press TILT-UP switch to check lid assembly for normal tilting. 9. Check sunroof lid assembly for normal operations (tilt-up, tilt-down, open, and close).
SBF920F
Removal
¼
NLBT0021
After any adjustment, check sunroof operation and lid alignment. ¼ Handle finisher plate and glass lid with care so not to cause damage. ¼ It is desirable for easy installation to mark each point before removal. CAUTION: Always work with a helper.
BT-50
SUNROOF
Removal (Cont'd)
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC
YBT115
EL IDX
*1
BT-34
*2
EL-252
BT-51
SUNROOF
Removal (Cont'd)
NBT180
BT-52
SUNROOF
Removal (Cont'd)
Record the number of shims placed between glass lid assembly and link and wire assembly. Remove securing screws and glass lid assembly.
GI MA EM
NBT145
LC
Remove shade stoppers (2 points) from rear end of sunroof frame assembly. Remove sun shade from rear end of sunroof frame assembly.
EC FE CL
NBT146
MT
Remove screws from left and right sides of each wind deflector holder. Then remove left and right sides of wind deflector holder. Remove screws from front end of sunroof unit. Then remove wind deflector from frame assembly. (If wind deflector is equipped).
AT AX SU BR
NBT147
CAUTION: ¼ Before removing sunroof motor, make sure that sunroof is fully closed. ¼ After removing sunroof motor, never attempt to rotate sunroof motor as a single unit.
ST RS
HA
NBT148
SC EL IDX
BT-53
SUNROOF
Trouble Diagnoses
Trouble Diagnoses
DIAGNOSTIC TABLE
=NLBT0022 NLBT0022S01
NOTE: For diagnosing electric malfunction, refer to "ELECTRIC SUNROOF" in EL section.
Check items (Components) Wind deflector (where fitted) Reference page Excessive wind noise Water leaks Symptom Sunroof rattles Excessive operation noise The numbers in this table mean checking order. 1 1 4 2 2 3 3 BT-54 1 Adjustment BT-55 2 1 2 Drain hoses BT-56 Weatherstrip BT-56 3 3 Link and wire assembly BT-57
WIND DEFLECTOR (WHERE FITTED)
1. 2. 3.
NLBT0022S02
Open lid. Check visually for proper installation. Check to ensure a proper amount of petroleum jelly has been applied to wind deflector connection points; apply if necessary.
SBT331
4.
Check that wind deflector is properly retracted by hand. If it is not, remove and visually check condition. (Refer to removal procedures, BT-50.) If wind deflector is damaged, replace with new one. If wind deflector is not damaged, re-install properly.
SBT332
BT-54
SUNROOF
Trouble Diagnoses (Cont'd)
ADJUSTMENT
NLBT0022S03
GI MA EM LC EC FE CL MT AT
NBT150
AX SU BR ST RS
If any height difference between glass lid and roof is found, check glass lid fit and adjust as follows:
Height Difference Adjustment
1. 2. 3. ¼ ¼
NLBT0022S0302
Tilt glass lid up and down. Check height difference between roof panel and glass lid to see if it is as "A-A" as shown in the figure above. If necessary, adjust it by using one of following procedures. Adjust by adding or removing adjustment shim(s) between glass lid and link assembly. If glass lid protrudes above roof panel, add shim(s) or plain washer(s) at sunroof mounting bracket or stud bolt locations to adjust sunroof installation as required.
HA SC EL IDX
BT-55
SUNROOF
Trouble Diagnoses (Cont'd)
DRAIN HOSES
NLBT0022S04
SBT005A
1. 2.
Remove headliner to access drain hose connections. (Refer to "ROOF TRIM", BT-34, for detail.) Check visually for proper connections, damage or deterioration. (The figure shows only the front side.)
NBT151
3.
4. 5. ¼
If leakage occurs around luggage room, remove luggage room side trim and check connecting area. Check for proper connection, damage or tear. Remove drain hoses and check visually for any damage, cracks, or deterioration. Pour water into drain hoses and find damaged portion. If any damaged portion is found at each step, replace the damaged part.
NBT152
WEATHERSTRIP
¼ 1. 2.
NLBT0022S05
In the case of leakage around glass lid, close glass lid and pour water over glass lid to find damaged or gap portion. Remove glass lid assembly. (Refer to removal procedures, BT-50, for details.) Visually check weatherstrip for proper installation. If a gap exists between glass lid and weatherstrip, check for sufficient amount of butyl seal. If required, remove weatherstrip and apply butyl seal. Refer to "EXTERIOR", BT-37, for details.
BT-56
SUNROOF
Trouble Diagnoses (Cont'd)
Check weatherstrip visually for any damage, deterioration, or flattening. ¼ If any damage is found, replace weatherstrip. CAUTION: Do not remove weatherstrip except when replacing, or filling up butyl seal.
3.
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
LINK AND WIRE ASSEMBLY
NLBT0022S06
NOTE: Before replacing a suspect part, carefully ensure it is the source of noise being experienced. 1. Check link to determine if coating film has peeled off to such an extent that substrate is visible. Check also to determine if link is the source of noise. If it is, replace it. 2. Visually check to determine if a sufficient amount of petroleum jelly has been applied to wire or rail groove. If not, add petroleum jelly as required. 3. Check wire for any damage or deterioration. If any damage is found, remove rear guide (refer to removal procedures, BT-50, for details), then replace wire.
HA SC EL IDX
BT-57
WINDSHIELD AND WINDOWS
Removal and Installation
Removal and Installation
REMOVAL
NLBT0023 NLBT0023S01
SBF034BA
After removing moldings, remove glass using piano wire or power cutting tool and an inflatable pump bag. WARNING: When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent glass splinters from entering your eyes or cutting your hands. CAUTION: ¼ Be careful not to scratch the glass when removing. ¼ Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
¼
NLBT0023S02
SBT472
SBT473
Use a genuine Nissan Urethane Adhesive Kit or equivalent and follow the instructions furnished with it. ¼ While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out by passenger compartment air pressure when a door is closed. ¼ The molding must be installed securely so that it is in position and leaves no gap. ¼ Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely cured (preferably 24 hours). Curing time varies with temperature and humidity. WARNING: ¼ Keep heat and open flames away as primers and adhesive are flammable. ¼ The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid contact with the skin and eyes. ¼ Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled. If affected by vapor inhalation, immediately move to an area with fresh air. ¼ Driving the vehicle before the urethane adhesive has completely cured may affect the performance of the windshield in case of an accident. CAUTION: ¼ Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box. ¼ Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
BT-58
WINDSHIELD AND WINDOWS
Removal and Installation (Cont'd)
¼ ¼
Do not leave primers or adhesive cartridge unattended with their caps open or off. The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely cured. Curing time varies depending on temperature and humidities. The curing time will increase under higher temperatures and lower humidities.
NLBT0023S03
GI MA EM LC EC FE CL MT AT AX SU BR ST
WINDSHIELD
NBT129
RS
Repairing Water Leaks for Windshield
NLBT0023S0301
Leaks can be repaired without removing and reinstalling glass. If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage. This can be done by applying water to the windshield area while pushing glass outward. To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
HA SC EL IDX
BT-59
WINDSHIELD AND WINDOWS
Removal and Installation (Cont'd)
SIDE WINDOW
NLBT0023S04
NBT130
BT-60
WINDSHIELD AND WINDOWS
Removal and Installation (Cont'd)
BACK DOOR WINDOW
¼
NLBT0023S05
Structure and removal/reinstallation method of back door window are basically the same as for the windshield.
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT132
BT-61
DOOR MIRROR
Removal and Installation
Removal and Installation
CAUTION: Be careful not to scratch door rearview mirror body. 5 For Wiring Diagram, refer to EL-254, "DOOR MIRROR" for details. 1. Remove front corner of door inner cover. 2. Disconnect door mirror harness connector. 3. Remove bolts securing door mirror assembly. 4. Remove the mirror glass. Do not insert flat-bladed screwdriver too far.
NLBT0024
NBT131
BT-62
REAR VIEW MIRROR
Removal and Installation
Removal and Installation
REMOVAL
NLBT0025 NLBT0025S01
GI MA EM LC EC FE CL MT AT AX
NBT059
SU BR
INSTALLATION
1. a.
NLBT0025S02
b. c. d.
NBT157
e. f. g. h. 2.
Install mirror base as follows: Determine mirror base position on windshield by measuring from top of windshield to top of mirror base as shown in the figure. Mark location on outside of windshield with wax pencil or equivalent. Clean attaching point on inside of windshield with an alcoholsaturated panel towel. Sand bonding surface of mirror base with sandpaper (No. 320 or No. 360). Clean bonding surface of mirror base with an alcohol-saturated paper towel. Apply Loctite Adhesive 11067-2 or equivalent to bonding surface of mirror base. Install mirror base at premarked position and press mirror base against glass for 30 to 60 seconds. After five minutes, wipe off excess adhesive with an alcoholmoistened paper towel. Install rearview mirror.
ST RS
HA SC EL IDX
BT-63
BODY (ALIGNMENT)
Alignment
Alignment
¼ ¼ ¼ ¼ ¼ ¼
NLBT0026
All dimensions indicated in figures are actual ones. When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself to make sure there is no free play. When a measuring tape is used, check to be sure there is no elongation, twisting or bending. Measurements should be taken at the center of the mounting holes. An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side is symmetrically the same value. The coordinates of the measurement points are the distances measured from the standard line of "X", "Y" and "Z".
SBF874GB
BT-64
BODY (ALIGNMENT)
Alignment (Cont'd)
ENGINE COMPARTMENT Measurement
NLBT0026S01 NLBT0026S0101
GI MA EM LC EC FE CL MT AT AX SU
NBT153
BR ST RS
HA SC EL IDX
BT-65
BODY (ALIGNMENT)
Alignment (Cont'd)
Measurement Points
NLBT0026S0102
NBT154
BT-66
BODY (ALIGNMENT)
Alignment (Cont'd)
UNDERBODY Measurement
NLBT0026S02 NLBT0026S0201
GI MA EM LC EC FE CL MT AT AX SU BR ST RS
HA SC EL IDX
NBT155
BT-67
BODY (ALIGNMENT)
Alignment (Cont'd)
Measurement Points
NLBT0026S0202
NBT156
BT-68