Text preview for : HP2033-TE.pdf part of MAKITA HP2033-TE MAKITA HP2033-TE.pdf
Back to : HP2033-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. HP2033
New Tool
Description 20mm 2-speed motor drill
CONCEPTION AND MAIN APPLICATIONS HP2032 370m
m (14-1/2")
m (14-1/2")
Model HP2032/HP2033 are sister versions of the existing model HP2033 368m
195mm (7-5/8")
HP2030/HP2031.
And they are designed for more professional use than
HP2030/HP2031. Their brief benefit is: 31mm
(1-1/4")
*More strong housing than HP2030/HP2031 by aluminum Gear
housing and Cam housing.
HP2032 ------- With key drill chuck
HP2033 ------- Keyless drill chuck
Width 75mm (2-15/16")
Specifications
Continuous Rating (W) Max.
Voltage (V) Current (A) Cycle (Hz) Output(W)
Input Output
100 7.6 50/60 720 330 620
115 6.6 50/60 720 330 620
200 3.8 50/60 720 330 620
220 3.4 50/60 720 330 620
230 3.3 50/60 720 330 620
240 3.2 50/60 720 330 620
No load speed Rotations Low speed 0-850 rpm
per minute High speed 0-2900 rpm
Blows Low speed 0-9400 rpm
per minute High speed 0-3200 rpm
Drill chuck capacity 1.5-13mm
Max. drilling capacities Concrete L:N/A H:20mm
(L/H) Steel L:13mm H:8mm
Wood L:40mm H:25mm
Net weight 2.5kg
Cord length 2.5m
Standard equipment
Chuck key S13------------------------1 pc. (HP2032 only)
Key holder 12-------------------------1 pc.(HP2032 only)
Depth gauge---------------------------1 pc.
Plastic carrying case------------------1 pc.
[Note] The standard equipment may differ from country to country.
Optional accessories
T.C.T. Hammer Bit 5.0-70 ~19.0-220
Hole Saw Ass'y 79mm, 95mm
Blow out bulb 64
Features and benefits
Strong aluminum Gear housing and cam housing
Features and benefits
Strong aluminum Gear housing
and Cam housing
Repair
Procedures other than listed below are the same as for HP2030
*Removal of cam B
To take cam apart from cam housing for the sake of recycle, etc., remove the cam with a
slotted driver as shown in the figure. Use repair tool "IR-020" to remove cam A.
Slotted driver
Com housing
Wiring diagram
Black
Black Field
White
Power supply coad Switch
2 Purple
C2
3 2
M2
M1
1
C1 1 4
Black Black Orange
Black
Transparent
Noise suppressor
Ground to the field steel plate.
*Noise suppressor or suppressor without earth wire will not be used for certain countries.
Noise suppressor may differ from country to country.
Putting lead wires into motor housing
Pass 'capacitor grounding
wire' inside the rib.
Rib
Rib
Brush holder lead wire Pass black lead wire
(Orange) inside the rib.
Pass field lead wire (white) as shown in the Pass field lead wire (black) as shown in the
figure. Contain 'grounding wire' of noise figure. Contain 'black lead wire' and 'brush
suppressor and 'brush holder lead wire holder lead wire (purple)' in the lead holder.
(purple)' in the lead holder. Brush holder lead wire (purple) should be
('Grounding wire' of noise suppressor should under the black lead wire.
be under the 'brush holder lead wire'.)
Field lead wire
(white) Field lead wire
(black)
Grounding wire of
noise suppressor
Rib Lead wire Brush holder lead wire
(black) (purple)
Pass black lead
wire inside the rib.
[Note] Connect wires as same as this description even if the noise suppressor is not used.
Putting away lead wires into handle
Pass 'black lead wire' and
'grounding wire of noise
suppressor' between boss
and bearing box.
Contain lead wires
in thr lead holder
Noise suppressor
[Note] Contain wires as same as this description even if the noise suppressor is not used.