Text preview for : control protocol Ver. 6.3.PDF part of DENON control protocol Ver. 6.3 DENON Home Theatre System Home Theatre System Denon - S-302 control protocol Ver. 6.3.PDF
Back to : control protocol Ver. 6.3 | Home
DENON AVR/AVC control protocol
Ver. 6.3
Application model : S-302
Application terminal : RS-232C
Connector specification
Connector type: DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format:
Synchronous system : Tone step synchronization
Communication system : A half duplex
Communication speed : 9600bps
Character length : 8 bits
Parity control : None
Start bit : 1 bit
Stop bit : 1 bit
Communication procedure : Non procedural
Communication data length : 135 bytes (maximum)
-1-
Protocol specification
The following three data forms are defined.
COMMAND : The message sent to a system(AVR/AVC) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE : The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
if the `request command' (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms of receiving the COMMAND.
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification : The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,
AND carriage return(0x0D)--- It is used only as a pause sign.
Command structure : COMMAND + PARAMETER + CR(0x0D)
COMMAND : ASCII CODE of 2 characters
ex. SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex. DVD : function name
CDR/TAPE : function name
THX SURROUND EX : surround mode name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
-2-
The example of a command * is the meaning of 0x0D.
SIDVD : Select Input source DVD
MSTHX SURROUND EX : surround Mode Set to THX SURROUND EX
MVUP : Master Volume UP
PWON : system Power ON
PWSTANDBY : system PoWer STANDBY
SI? : Request command for now playing input source >> Return RESPONSE `SI***'
-3-
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel
volume of all channels , It described in B) ) returns as EVENT.
E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines "99".
J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three
ASCII characters as bellows.
ex. MASTER VOLUME = +1.0dB : MV81
+0.5dB : MV805
0dB : MV80
-0.5dB : MV795
-1.0dB : MV79
| |
-79.5dB : MV005
-80.0dB : MV00
--- : MV99
* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.
K) Four seconds later, please transmit the next COMMAND after transmitting a power on COMMAND PWON .
-4-
COMMAND and PARAMETER list (AMP)
COMMAND PARAMETER function example
PW ON POWER ON/STANDBY change PWON
STANDBY PWSTANDBY
? Request PW Status PW?
MV UP MASTER VOLUME UP/DOWN, direct change to ***dB MVUP
DOWN MVDOWN
** **:00 to 99 by ASCII, 80=0dB, 99=---(MIN) MV80
? Request MV Status MV?
CV FL UP CHANNEL VOLUME UP/DOWN, direct change to ***dB CVFL UP
FL DOWN ---FRONT Lch CVFL DOWN
FL ** **:38 to 62 by ASCII, 50=0dB CVFL 50
FR UP CVFR UP
FR DOWN ---FRONT Rch CVFR DOWN
FR ** **:38 to 62 by ASCII, 50=0dB CVFR 50
SW UP CVSW UP
SW DOWN ---SUBWOOFERch CVSW DOWN
SW ** **:00,38 to 62 by ASCII, 50=0dB, 00=OFF CVSW 50
? Request CV Status CV?
MU ON OUTPUT MUTE ON/OFF change MUON
OFF MUOFF
? Request MU Status MU?
MV , CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 (J) section)
-5-
COMMAND PARAMETER function example
SI DVD Select INPUT source SIDVD
TUNER SITUNER
VCR-1 (AUX1) SIVCR-1
VCR-2 (AUX2) SIVCR-2
CDR/TAPE1 (AUX3) SICDR/TAPE1
V.AUX (FRONT IN) SIV.AUX
NET/USB SINET/USB
IPOD SIIPOD
OPTICAL SIOPTICAL
COAXIAL SICOAXIAL
? Request SI Status SI?
SD AUTO set DIGITAL INPUT AUTO mode SDAUTO
PCM set DIGITAL INPUT PCM mode SDPCM
DTS set DIGITAL INPUT DTS mode SDDTS
ANALOG set force ANALOG INPUT mode SDANALOG
MS STEREO SURROUND mode set MSSTEREO
ROCK ARENA MSROCK ARENA
JAZZ CLUB MSJAZZ CLUB
DOLBY H/P MSDOLBY H/P
DVS REF. MSDVS REF.
DVS WIDE MSDVS WIDE
? Return MS Status MS?
-6-
EVENT(or RESPONSE) and PARAMETER list (AMP)
EVENT PARAMETER function example
PW ON POWER ON/STANDBY change PWON
STANDBY PWSTANDBY
MV ** MASTER VOLUME change, **:00 to 99 by ASCII MV80
98 = +18dB(MAX)
80 = 0dB
10 = -70dB
00 = -80dB
99 = ---(MIN)
CV FL ** CHANNEL VOLUME change, **:00 to 62 by ASCII CVFL **
CVFR 50
CVSW 50
FR ** 62 = +12dB(MAX), 38 = -12dB(MIN) CVFL 50
CVFR **
CVSW 50
SW ** 50 = 0dB CVFL 50
CVFR 50
CVSW **
MU ON OUTPUT MUTE ON/OFF change MUON
OFF MUOFF
SI DVD INPUT source change SIDVD
TUNER SITUNER
VCR-1 SIVCR-1
VCR-2 SIVCR-2
CDR/TAPE1 SICDR/TAPE1
NET/USB SINET/USB
IPOD SIIPOD
V.AUX SIV.AUX
SD 1
AUTO DIGITAL INPUT mode change SDAUTO
PCM SDPCM
DTS SDDTS
ANALOG SDANALOG
MS STEREO SURROUND mode change MSSTEREO
-7-
ROCK ARENA MSROCK ARENA
JAZZ CLUB MSJAZZ CLUB
DOLBY H/P MSDOLBY H/P
DVS REF.+PL2 C MSDVS REF.+PL2 C
DVS WIDE+PL2 C MSDVS WIDE+PL2 C
The PARAMETER of MV , CV EVENT : Uses two ASCII characters. (see page 6 J) section)
1 SD COMMAND is no RESPONSE.
-8-
COMMAND and PARAMETER list (TUNER)
COMMAND PARAMETER function example
TF UP TUNER Frequency UP/DOWN TFUP
DOWN TFDOWN
****** --- ****.** kHz at AM band (>050000 is AM.) TF105000
(6 digits) ****.** MHz at FM band (<050000 is FM.) (1050.00kHz at AM)
? Return TF Status TF?
TP UP TUNER PRESET CH UP/DOWN , direct change to No.** TPUP
DOWN TPDOWN
**(PRESET No.) TP10
(PRESET No."10")
? Return TP Status TP?
TM TUNER BAND , MODE Select
AM ---Band set to AM TMAM
FM ---Band set to FM TMFM
? Return TM Status TM?
AUTO ---Tuning mode set to AUTO mode TMAUTO
MANUAL ---Tuning mode set to MANUAL mode TMMANUAL
TF COMMAND : '*' parameters can NOT operate when INPUT source isn't TUNER.
-9-
EVENT(or RESPONSE) and PARAMETER list (TUNER)
EVENT PARAMETER function example
TF AN****** TUNER Frequency change TFAN105000
(6 digits)
--- ****.** kHz at AM band (1050.00kHz at AM)
****.** MHz at FM band
TP AN**(PRESET No.) TUNER PRESET change to No.** TPANA1
(PRESET No."A1")
TM TUNER BAND , MODE change
ANAM ---Band set to AM TMANAM
ANFM ---Band set to FM TMANFM
ANAUTO ---Tuning mode set to AUTO mode TMANAUTO
ANMANUAL ---Tuning mode set to MANUAL mode TMANMANUAL
- 10 -
COMMAND and PARAMETER list (timer)
COMMAND PARAMETER Function example
TS ONCE @**##-@$$%% [F][N] ONCE TIMER TIME SET TSONCE A0730-A0830 DV00
@:A or P or 2(A:AM,P:PM,2:24hour by ASCII) TSONCE P0630-P1130 TU01
**## :start time(**=00~23hours,##=00~59minutes by ASCII) TSONCE 21930-22030 IP00
$$%% :stop time($$=00~23hours,%%=00~59minutes by ASCII)
[F]:Function (2bytes by ASCII)
DV DVD PLAY
TU TUNER PLAY
IP iPod PLAY
[N]:preset No.(2bytes by ASCII, except TU="00")
EVERY @**##-@$$%% [F] [N] EVERY TIMER TIME SET TSEVERY P0630-P0700 DV00
@:A or P or 2(A:AM,P:PM,2:24hour by ASCII) TSEVERY P0630-P1100 TU01
**## :start time(**=00~23hours,##=00~59minutes by ASCII) TSEVERY 21830-21900 IP00
$$%% :stop time($$=00~23hours,%%=00~59minutes by ASCII)
[F]:Function (2bytes by ASCII)
It is the same as that of ONCE TIMER TIME SET.
[N]:preset No.(2bytes by ASCII, except TU="00")
SLEEP *** SPLEEP TIMER SET TSSLEEP 060
***:120,090,060,050,040,030,020,010,000(minutes)
(000=sleep timer off)
TO OFF OFF TIMER ON/OFF OFF OFF :once=off, every=off TOOFF OFF
OFF ON OFF ON :once=off, every= on TOOFF ON
ON OFF ON OFF :once= on, every=off TOON OFF
ON ON ON ON :once= on, every= on TOON ON
TI @**## TIME SET TIA0730
@:A or P or 2(A:AM,P:PM,2:24hour by ASCII) TIP1130
**## :now time(**=00~23hours,##=00~59minutes by ASCII) TI21930
- 11 -
EVENT(or RESPONSE) and PARAMETER list (timer)
EVENT PARAMETER function example
TS ONCE @**##-@$$%% [F][N] ONCE TIMER TIME SET TSONCE A0730-A0830 DV00
@:A or P or 2(A:AM,P:PM,2:24hour by ASCII) TSONCE P0630-P1130 TU01
**## :start time(**=00~23hours,##=00~59minutes by ASCII) TSONCE 21930-22030 IP00
$$%% :stop time($$=00~23hours,%%=00~59minutes by ASCII)
[F]:Function (2bytes by ASCII)
DV DVD PLAY
TU TUNER PLAY
IP iPod PLAY
[N]:preset No.(2bytes by ASCII, except TU="00")
EVERY @**##-@$$%% [F][N] EVERY TIMER TIME SET TSEVERY P0630-P0700 DV00
@:A or P or 2(A:AM,P:PM,2:24hour by ASCII) TSEVERY P0630-P1100 TU01
**## :start time(**=00~23hours,##=00~59minutes by ASCII) TSEVERY 21830-21900 IP00
$$%% :stop time($$=00~23hours,%%=00~59minutes by ASCII)
[F]:Function (2bytes by ASCII)
It is the same as that of ONCE TIMER TIME SET.
[N]:preset No.(2bytes by ASCII, except TU="00")
SLEEP *** SPLEEP TIMER SET TSSLEEP 060
***:120,090,060,050,040,030,020,010,000(minutes)
(000=sleep timer off)
TO OFF OFF TIMER ON/OFF OFF OFF :once=off, every=off TOOFF OFF
OFF ON OFF ON :once=off, every= on TOOFF ON
ON OFF ON OFF :once= on, every=off TOON OFF
ON ON ON ON :once= on, every= on TOON ON
TI @**## TIME SET TIA0730
@:A or P or 2(A:AM,P:PM,2:24hour by ASCII) TIP1130
**## :now time(**=00~23hours,##=00~59minutes by ASCII) TI21930
When time is not set, the **## equal "----" TI2----
- 12 -
COMMAND and PARAMETER list DVD
COMMAND PARAMETER function example
D@ start disk playback (PLAY) D@
DA stop disk playback (STOP) DA
DB pause to play disc (PAUSE) DB
DC + skip to the next track or chapter(SKIP >>|) DC+
- skip to the previous track or chapter (SKIP |<<) DC-
DD + change the playback speed (slow/search >>) DD+
- change the playback speed (slow/search <<) DD-
? get the playback speed information DD?
DE change the default settings(SETUP) DE
DF display the top menu stored on the disc (TOP MENU) DF
DG display the DVD menu stored on the disc (MENU) DG
DH return to the previous menu screen (RETURN) DH
DI + switch forward the audio stream (AUDIO) DI+
- switch backward the audio stream (AUDIO) DI-
? get the audio information DI?
DJ + switch forward the subtitle language (SUBTITLE) DJ+
- switch backward the subtitle language (SUBTITLE) DJ-
? get the subtitle information DJ?
DK + switch forward the angle (ANGLE) DK+
- switch backward the angle (ANGLE) DK-
? get the angle information DK?
DL 1 *** select directly group or title number DL1 002
***:group or title number(001 to 999 by ASCII)
2 *** select directly track or chapter number DL2 005
***:track or chapter number(001 to 999 by ASCII)
? get group/title and track/chapter information DL?
DM 1 move the highlight area ( ) DM1
2 move the highlight area ( ) DM2
3 move the highlight area ( ) DM3
4 move the highlight area ( ) DM4
DN select the item selected with the cursor buttons(ENTER) DN
- 13 -
DP 1 select the HDMI/DVI format of 480/576P DP1
2 select the HDMI/DVI format of 720P DP2
3 select the HDMI/DVI format of 1080I DP3
4 select the HDMI/DVI format of 1080P DP4
5 select the HDMI/DVI format of AUTO DP5
? get the HDMI/DVI format information DP?
DQ 1 select the HDMI/DVI Video Setup of Y Cb Cr DQ1
2 select the HDMI/DVI Video Setup of RGB DQ2
? get the HDMI/DVI Video Setup information DQ?
D0 ? Acquire system status D0?
D1 ? Acquire software Version D1?
D2 ? Acquire DVD error status D2?
- 14 -
EVENT(or RESPONSE) and PARAMETER (DVD)
EVENT PARAMETER function example
D@ disk playback starts (PLAY) D@
DA disk playback stops (STOP) DA
DB pause to play disc (PAUSE) DB
DC ** ### Change the playback track or chapter DC01 015
**:current group or title number(01-99 by ASCII)
###:current track or chapter number(001-999 by ASCII)
DD 1 change the playback speed [1] slow FWD x 1/8 DD1
2 [2] slow FWD x 1/6 DD2
3 [3] slow FWD x 1/4 DD3
4 [4] slow FWD x 1/2 DD4
5 [5] slow RVS x 1/8 DD5
6 [6] slow RVS x 1/6 DD6
7 [7] slow RVS x 1/4 DD7
8 [8] slow RVS x 1/2 DD8
9 [9] FF1 DD9
: [:] FF2 DD:
; [;] FF3 DD;
< [<] FF4 DD<
= [=] FF5 DD=
> [>] FF6 DD>
? [?] FF7 DD?
@ [@] FR1 DD@
A [A] FR2 DDA
B [B] FR3 DDB
C [C] FR4 DDC
D [D] FR5 DDD
E [E] FR6 DDE
F [F] FR7 DDF
G [G] NORMAL DDG
- 15 -
EVENT PARAMETER function example
DE enter the setup menu (SETUP) DE
DF display the top menu stored on the disc (TOP MENU) DF
DG display the DVD menu stored on the disc (MENU) DG
DH return to the previous menu screen (RETURN) DH
DI [1][2][3][4][5] change the audio stream channel (AUDIO) DI13182
(5 characters) [1] current audio stream channel(1-8 by ASCII) (1/3 Dolby 5.1ch English)
[2] total audio stream channel (1-8 by ASCII) DI11421
[3] audio format (1/1 LPCM 2ch Japanese)
1 Dolby Digital 2 DTS
3 MPEG 4 LPCM
5 PPCM 6 OTHER
7 DSD
[4] audio channel
1 1ch 2 2ch
3 2.1ch 4 3ch
5 3.1ch 6 4ch
7 4.1ch 8 5ch
9 5.1ch : 6ch
; L/R(CD/VDC/MP3) < R(CD/VDC/MP3)
= L(CD/VDC/MP3) > UNKNOWN
[5] Dialog code
1 JPN 2 ENG
3 FRA 4 DEU
5 ITA 6 ESP
7 NLD 8 CHI
9 RUS : KOR
; UNKNOWN
- 16 -
EVENT PARAMETER function example
DJ ** ## @ change the subtitle language (SUBTITLE) DJ01 03 1
**:current subtitle stream channel(01-32 by ASCII)
##:total subtitle stream channel(01-32 by ASCII)
@:LANGUAGE CODE(by ASCCI)
1 JPN 2 ENG
3 FRA 4 DEU
5 ITA 6 ESP
7 NLD 8 CHI
9 RUS : KOR
; UNKNOWN
DK * # change forward the angle (ANGLE) DK1 3
*:current angle stream channel(1-9 by ASCII)
#:total angle stream channel(1-9 by ASCII)
DL ** ### select directly group or title number DL1 002
**:current group or title number(01 to 99 by ASCII)
###:current track or chapter number(001 to 999 by ASCII) DL2 005
DM move the highlight area DM
DN select the item selected with the cursor buttons DN
DP 1 select the HDMI/DVI format of 480/576P DP1
2 select the HDMI/DVI format of 720P DP2
3 select the HDMI/DVI format of 1080I DP3
4 select the HDMI/DVI format of 1080P DP4
5 select the HDMI/DVI format of AUTO DP5
DQ 1 select the HDMI/DVI Video Setup of HDMI Y Cb Cr DQ1
2 select the HDMI/DVI Video Setup of HDMI RGB DQ2
- 17 -
EVENT PARAMETER function example
D0 [1]~[22] DVD player's status information D01191118101010700503011
(22 characters) [1] Disc type code (DVD VUDEO, Dolby DIGITAL 5.1ch
1 DVD VIDEO 2 DVD AUDIO Dialog=JPN, Subtitle=JPN
3 VCD 4 CD-DA Angle=1, Playing, Normal play
5 MP3 6 UNKNOWN Title=01, Chapter=010
7 SACD Title Elapsed 00:50:30,
[2] Audio format code HDMI Format=480/576P,
1 DOLBY DIGITAL 2 DTS HDMI/DVI Video Setup=HDMI Y Cb
Cr)
3 MPEG 4 LPCM
5 PPCM 6 UNKNOWN
7 DSD
[3] Audio Channel code
1 1ch 2 2ch
3 2.1ch 4 3ch
5 3.1ch 6 4ch
7 4.1ch 8 5ch
9 5.1ch : 6ch
; L/R(CD/VDC/MP3) < R(CD/VDC/MP3)
= L(CD/VDC/MP3) > UNKNOWN
[4] Dialog code
1 JPN 2 ENG
3 FRA 4 DEU
5 ITA 6 ESP
7 NLD 8 CHI
9 RUS : KOR
; UNKNOWN
[5] Subtitle code
1 JPN 2 ENG
3 FRA 4 DEU
5 ITA 6 ESP
7 NLD 8 CHI
9 RUS : KOR
; UNKNOWN
- 18 -
EVENT PARAMETER function example
[6] Angle code
1 1 2 2
3 3 4 4
5 5 6 6
7 7 8 8
9 9
[7] Status code
0 Stand-by
1 Disc Loading
2 Disc Loading Complete
3 Tray Open
4 Tray Close
A No Disc
B Stop
C Play
D Pause
E Scan Play
F Slow Scan Play
G Setup
H Play Back Control
I DVD Resume Stop
J DVD Menu
[8] Play mode code
1 NORMAL 2 PROGRAM
3 RANDOM 0
[9][10] Group or Title number (01-99 by ASCII)
[11][12][13] Track or Chapter number (001-999 by ASCII)
- 19 -
EVENT PARAMETER function example
[14] Time mode
1 SINGLE ELAPSED 2 SINGLE REMAIN
3 TOTAL ELAPSED 4 TOTAL REMAIN
5 CHAPTER ELAPSED 6 CHAPTER REMAIN
7 TITLE ELAPSED 8 TITLE REMAIN
9 TRACK ELAPSED : TRACK REMAIN
; GROUP ELAPSED < GROUP REMAIN
[15][16] Elapsed Time(hours,00-99 by ASCII)
[17][18] Elapsed Time(minutes,00-59 by ASCII)
[19][20] Elapsed Time(seconds,00-59 by ASCII)
[21] HDMI Format
1 480/576P 2 720P
3 1080I 4 1080P
5 AUTO
[22] DVI/HDMI Video Setup
1 HDMI Y Cb Cr 2 HDMI R G B
3 DVI 4 OFF
D1 [1]~[24] software version information D1000000111111222222333333
(24 characters) [1]~[6] SYSTEM uCOM version (6 figure) (SYSTEM:0000-00,
[7]~[12] DSP version (6 figure) DSP:1111-11,
[13]~[18] DVD F/E version (6 figure) F/E:2222-22,
[19]~[24] DVD B/E version (6 figure) B/E:3333-33, )
- 20 -
EVENT PARAMETER function example
D2 [1][2] [1] 1st error code (0x20 to 0x2D by binary) D1[0x20][0x00]
[2] 2nd error code (0x00 by binary)
Error code
No. 1st 2nd detail
1 0x20 0x00 Loading error
2 0x21 0x00 Loading switch error
3 0x22 0x00 Focus servo error
4 0x23 0x00 Tracking servo error
5 0x24 0x00 Cannot adjust offset value
for servo circuit
6 0x25 0x00 Cannot adjust gain value
for servo circuit
7 0x26 0x00 Focusing fail
during playing or searching or pausing
8 0x27 0x00 During spinup, data of disc does not read
9 0x28 0x00 During play, data of disc does not read
10 0x29 0x00 Cannot read within a present time period
in TOC reading
11 0x2A 0x00 Subcode data does not read
12 0x2C 0x00 Command error occurs
13 0x2D 0x00 Focusing fail in scanning
- 21 -
COMMAND and PARAMETER list (EX)
COMMAND PARAMETER function example
EX PLAYPAUSE For iPod, USB function EXPLAYPAUSE
PLAY For iPod, USB function EXPLAY
PAUSE For iPod, USB function EXPAUSE
STOP For USB function EXSTOP
AUTOFWD For iPod, USB function EXAUTOFWD
AUTORVS For iPod, USB function EXAUTORVS
MANUFWD For iPod function EXMANUFWD
MANURVS For iPod function EXMANURVS
UP For iPod, USB function EXUP
DOWN For iPod, USB function EXDOWN
LEFT For iPod, USB function EXLEFT
RIGHT For iPod, USB function EXRIGHT
ENTER For iPod, USB function EXENTER
MENU For iPod function EXMENU
RANDOM For iPod, USB function EXRANDOM
REPEAT For iPod, USB function EXREPEAT
RETURN For iPod, USB function EXRETURN
DISPLAY For iPod, USB function EXDISPLAY
NSE0 Request Onscreen Display Information List EXNSE0
(UTF-8 CODE Character)
For iPod, USB function
- 22 -
EVENT(or RESPONSE) and PARAMETER (EX)
EVENT PARAMETER function
EX RCV EXRCV
Onscreen Display Information(mserver/iRadio) is
Answered By the NSE Command.
NSE0 Display Folder Information EXNSE0************
NSE1 Display Line1 Information EXNSE1************
NSE2 Display Line2 Information EXNSE2************
NSE3 Display Line3 Information EXNSE3************
NSE4 Display Line4 Information EXNSE4************
NSE5 Display Line5 Information EXNSE5************
NSE6 Display Line6 Information EXNSE6************
NSE7 Display Line7 Information EXNSE7************