Text preview for : HM1130C-TE.pdf part of MAKITA HM1130C-TE MAKITA HM1130C-TE.pdf
Back to : HM1130C-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. HM1130C
New Tool
Description 98mm(3-7/8")
Demolition Hammers
7/8")
CONCEPTION AND MAIN APPLICATIONS
m(8-
These demolition hammer models are newly added as a
224m
Makita Hex. Shank model (l7mm hex.) and their basic
specifications are the same as Makita current models
HM1100/HM1l00C (SDS-Max Shank).
HM1130C has an el ectronical speed control feature.
/4")
m( 20-1
515m
Specifications
Continuous Rating (W)
Voltage (V) Current (A) Cycle (Hz) Max. Output(W)
Input Output
100 11.0 50/60 1050 450 1050
115 9.6 50/60 1050 450 1050
200 5.5 50/60 1050 450 1050
220 5.0 50/60 1050 450 1050
230 4.8 50/60 1050 450 1050
240 4.6 50/60 1050 450 1050
Bit-type Hex. Shank
Blows per minute HM1130C 1300-2650 (bpm)
HM1130 2650 (bpm)
Net Weight 6.1kg (13.4 lbs)
Cord Length 5m (16.4 ft)
Standard equipment
Bit Grease
Bull-Point 17-280
Optional accessories
Bull Point 17-280 Cold Chisel 19-280
Bull Point 17-450 Cold Chisel 19-450
Scaling Chisel 50-280 Clay Spade 105-400
Rammer 140 Bushing Tool
Grooving Chisel 22-280 Blow-out bulb
Grooving Chisel 26-280 Hammer Grease (30g)
Features and benefits
See the attached sheets for more information.
The standard equipment for the tools shown may differ form country to country.
New chuck for simple chisel locking and easy-changing.
A chisel can be locked only by pushed-in chuck
and easier changed by sliding a sleeve.
Speed Adjusting Dial (HM1130C only)
360
Constant speed and Soft start (HM1130C only)
Dust-proot Cap helps protect the machine against dust.
Repair
Since the repairing methods are the same as HM1100C other than descried below, see the new products technical
information(BL-2403) of HM1100C.
Disassembling/assembling of tool holder
(1) Disassembling
1. Pull out the tool holder cover by the one hand(order (1)) and
remove the tool holder cap by the other hand(order (2))Once
the tool holder cap has been removed, the tool holder cover
and compression spring 46 can be removed.
2
Tool holder cap
1
Tool holder cover
2. Use the circle clip plyer to disconnect the circle
clip(shaft)round S-40, and then remove the washer 40,
compression spring 47 and spring guide.
Circle clip(shaft)round S-40
Washer 40
Compression spring 47
Spring guide
3. Manually expand the gap on the leaf spring 37 to
remove it from the tool holder and then pull out the pin 8
with step. Use the circle clip plyer to remove the ring
spring 27, and the chuck ring can be disconnected
upward.
Ring spring 27
Chuck ring
Pin with step Leaf spring 37
Gap
Tool holder
4. Disconnect the side handle support upward in the same
way as HM1100C and loosen the hexagon holed bolt
M6x30 using the Hex. wrench to remove the tool
holder.
Tool holder
Side handle support
Hex. socket head bolt
M6x30
(2) Assembling
1. To assemble the cylinder liner 34 with Make fit
the sleeve 39, make fit the positions of 3
holes on the cylinder liner to the
elongation hole on the sleeve 39.
Cylinder liner 34
Sleeve 39
2. Make fit the dent portion on the leaf
spring 37 to the groove on the chuck
ring to assemble them. Make fit
Chuck ring
Leaf spring 37
3. Make fit the two grooves on the tool holder
Marks on the tool
to the two marks on the tool holder cap to
holder cap
assemble them.
(The protrusion on the back of mark can be
housed in the groove on the tool holder.)
Make fit
Groove on the tool holder
Greasing points( )(only the points which are different from the ones for HM1100C)
MAKITA GREASE N NO.2
Steel ball 7, 9
Pin 8 with step
MAKITA GREASE R NO. 00
MAKITA GREASE R NO. 00
X ring 28 inside the tool holder and
all the circumference on the O ring 27
All the circumference on the O ring 22 inside the sleeve guide
Circuit drawing
HM1130
The condenser is not used depending on the destinations.
Connector at closed end
Capasitor
Switch C
6 4 Black
Cab tire cord
3 1 CH
choke coil Orange color
The lead wire instead of chalk coil
may be used depending on the destinations. Mechanically wound field
(support mounted)
HM1130C
Controller
Connector at closed end
Switch
Red Black Black
6 4
Cab tire cord White or Light brown
3 1
Orange color
Mechanically wound field
(support mounted)
HM1130C
Capasitor
C Controller
Connector at closed end
Switch
6 4 Red Black Black
Cab tire cord White or
3 1 Light brown
CH
choke coil Orange color
The lead wire instead of chalk coil
may be used depending on the destinations.
Mechanically wound field
(support mounted)