Text preview for : 07_Alignment & Adjustment.pdf part of Samsung 07 Alignment & Adjustment Samsung LCD TV LA32R71W 07_Alignment & Adjustment.pdf
Back to : 07_Alignment & Adjustment | Home
3 Alignments and Adjustments
3 Alignments and Adjustments
3-1 Service Instruction
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.
2. Use the specified test equipment or its equivalent.
3. Correct impedance matching is essential.
4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers, do not allow the marker generator to distort
test result.
5. Connect the TV only to an AC power source with voltage and frequency as specified on
the backcover nameplate.
6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.
7. To protect aganist shock hazard, use an isolation transform.
3-1
3 Alignments and Adjustments
3-2 How to Access Service Mode
3-2-1 Entering Factory Mode
" "
- If you have Factory remote - control
- The buttons are active in the service mode.
1. Remote - Control Key : Power, Arrow Up, Arrow Down, Arrow Left
Arrow Right, Menu, Enter, Number Key(0~9)
2. Function - Control Key : Power, CH +, CH -, VOL +, VOL -,
Menu, TV/VIDEO(Enter)
3-2-2 Panel Check
Specially for LA26,32R7**, You have to check Panel Maker Because of different adjustments as follows.
First of all, Check the label rating!
1) Label Rating File
Panel check
If Panel Mark is "A", Set the factory mode Panel BOM(Bill of material) : BN07-00247A
indicating as follows. Connector between Panel and Power Unit
: BN39-00603M (300mm)
Panel BOM(Bill of material) : BN07-00289A
Connector between Panel and Power Unit * Option Byte
: BN39-00603A (250mm) 1. Gamma "OFF"
2. Panel Option "AMLCD_INT"
* Option Byte
1. Gamma "AUO"
2. Panel Option "AUO_AMVA" Others are same shown below.
If Panel Mark is "S" or not printed.
Set the factory mode indicating as follows.
3-2
3 Alignments and Adjustments
3-3 Factory Data
1. Calibration
2. Option Table XXXX XXXX
3. White Balance
4. SVP-PX
5. Option Block
6. STV8257/STA323W
7. YC Delay
8. Adjust
9. I2C Check
10. W/B MOVIE
11. Checksum
12. Reset
13. Spread Spectrum
T-BRDMPEA-0161 (Main Micom Ver)
T-BRDMPEUS-1000 (Sub Micom Ver)
Month / Day / Year / Hour / Min. / Sec.
1. Calibration
1) AV Calibration
2) COMP Calibration
3) PC Calibration
4) HDMI Calibration
2. Option Table XXXX XXXX
Inch Option 32" Carrier Mute ON TTX Group Auto
Gamma OFF Language English Auto Power ON
Panel Option AMLCD_INT Auto FM ON Magazine LNA OFF
2HDMI OFF High Deviation OFF ---- G
Brt.Sensor OFF TTX ON ---- OFF
EnergySave ON TTX List Flof Debug OFF
LBE/FBE OFF ACR OFF Ch.Table SUWON
FRC(Micronas) OFF Dynamic CE ON iDTV_Cntry UK
FRC(Samsung) OFF Dynamic Dimming ON Dynamic Contrast OFF
LNA OFF Tuner TOP 8
3-3
3 Alignments and Adjustments
1. Calibration AV Calibration EXE
COMP Calibration EXE
PC Calibration EXE
HDMI Calibration EXE
2. Option Table
Inch Option 23"/32"/37"/40"/46"/57"
Gamma OFF/AUO/CMO/AMLCD
Panel Option AUO / CMO/AMLCD_INT/Panel3 / Panel4 / Panel5 / Panel6
2Hdmi OFF
Brt. Sensor FF
EnergySave ON
LBE/FBE OFF
FRC(Micronas) OFF
FRC2X OFF
LNA OFF
Carrier Mute ON
Language English
Auto FM ON
High Deviation OFF
TTX ON
TTX List Flof
ACR OFF
Dynamic CE ON
Dynamic Dimming ON
Tuner TOP 8
TTX Group Auto
Auto Power ON
Magazine LNA OFF
Debug OFF
Ch. Table SUWON
iDTV_Cntry UK
Dynamic Contrast OFF
BORDEAUX INCH OPTION
Panel Maker Gamma Panel Option
26 AUO AUO AUO
32 AUO AUO AUO
32 AMLCD OFF AMLCD_INT
37 AUO AUO AUO
40 AMLCD AMLCD AMLCD_INT
3-4
3 Alignments and Adjustments
3. White Balance Sub Brightness ADJ
R-Offset ADJ
G-Offset 128
B-Offset ADJ
Sub Contrast 100
R-Gain ADJ
G-Gain 128
B-Gain ADJ
4. SVP-PX ComB Filter Y-Filter 80H
Sharpness H2Gain 05H
H4Gain 02H
V2Gain 0CH
V4Gain 04H
Sr2Gain 02H
Sr4Gain 00H
Sl2Gain 02H
Sl4Gain 08H
Peakth1 04H
Peakth2 2F H
Peakth3 3F H
NR Y_NR_OFF 80H
C_NR_OFF 80H
Y_NR_ON 80H
C_NR_ON 80H
RGB Calibration R-Offset 48H
G-Offset 48H
B-Offset 48H
R-Gain 55H
G-Gain 55H
B-Gain 55H
ADC Calibration TCD3 Contrast 78H
TCD3 Brightness 20H
TCD3 CR 80H
TCD3 CB 80H
TCD3 Delay 00H
Analog Y Offset 41H
Analog PB Offset 80H
Analog PR Offset 80H
Analog Y Gain CBH
Analog PB Gain 9AH
Analog PR Gain 9AH
Black Level 00H
Svp Brightness 00H
3-5
3 Alignments and Adjustments
low high delta
Calibration Target AV ADC 17H D5H 02H
COMP ADC 0F H EBH 02H
PC ADC 17H D5H 04H
ALL RGB 00H DDH 08H
Color Management Skin Direction Reddish
Skin Enhane 40H
Green Stretch 00H
Blue Stretch 00H
5. Option block FRC(Micronas)
FRC2X
LBE/FBE Test Pattern 00H
BLACK_TILT 000
BlackGain_MAX 000
LOWER_FUNC 000
UPPER_FUNC 000
SKIN_EN 000
SKIN_T_X 000
SKIN_T_Y 000
ColorGain 000
6. STV8257/STA323W Ch1 Volume 40H
Ch2 Volume 40H
AGC Gain 06H
AV-Prescale 00H
AV Delay 41H
Comb Delay 41H
HDMI Delay 41H
PC Delay 41H
L1 Att/Rel Thres 7FH
3-6
3 Alignments and Adjustments
7. YC Delay RF PAL-B/G AAH
RF PAL-D/K 99H
RF PAL- I 99H
RF SECAM-B/G 88H
RF SECAM-D/K 44H
RF SECAM-L/L' 88H
RF NTSC3.58 66H
RF NTSC4.43 CCH
AV PAL AAH
AV SECAM 88H
AV NTSC 3.58 BBH
AV NTSC4.43 AAH
AV PAL60 77H
8. Adjust Video Mute Time 10
Melody Volume 9
Ana_Dimm_Max FEH
LNA PLUS RFDB-1 Level 2
RFDB-2 Level 5
RFDB-3 Level 9
RFDB-4 Level 24
Hotel Option Hotel Mode OFF
Power On Channel 1
Power On Volume 10
Max Volume 100
Local Key Lock OFF
Power On Source RF
3-7
3 Alignments and Adjustments
9. I2C Check EXE
10. W/B MOVIE WB Movie OFF
Color Mode Movie
W1 R Gain 161
W1 B Gain 74
W1 R Offset 119
W1 B Offset 140
W2 R Gain 162
W2 B Gain 47
W2 R Offset 113
W2 B Offset 146
Movie Contrast 70
Movie Brightness 50
Movie Color 45
Movie Sharpness 25
Movie Color Tone Warm2
11. Checksum EXE
12. Reset EXE
13. Spread Spectrum Spectrum ON
Delta 3
Positive 8
Negative 2
3-8
3 Alignments and Adjustments
3-4 Service Adjustment
3-4-1 White Balance - Calibration
If picture color is wrong, do calibration first.
Equipment : CA210, Patten : chess pattern
Execute calibration in Factory Mode
Source AV : PAL composite, Component : 1280*720/60Hz
PC : 1024*768/60Hz
( chess patten )
3-4-2 White Balance - Adjustment
If picture color is wrong, check White Balance condition.
Equipment : CA210, Patten : Toshiba
Adjust W/B in Factory Mode
Sub brightness and R/G/B Offset controls low light region
Sub contrast and R/G/B Gain controls high light region
Source AV : PAL composite, Component : 1280*720/60Hz
HDMI[DVI] : 1280*720/60Hz
[ Test Pattern : MSPG-945 Series Pattern #16 ]
*Color temperature
1500K +/-500, -6 ~-20 MPCD
*Color coordinate
H/L : 267/263 +/- 2 35.0 Ft +/- 2.0Ft
L/L : 270/260 +/- 3 1.5 Ft +/- 0.2Ft
Toshiba Patten
3-9
3 Alignments and Adjustments
3-4-3 Conditions for Measurement
1. On the basis of toshiba ABL pattern : High Light level (57 IRE)
- INPUT SIGNAL GENERATOR : MSPG-925LTH
* Mode NO 2 : 744X484@60 Hz
NO 6 : 1280X720@60 Hz
NO 21 : 1024X768@60 Hz
* Pattern NO 36 : 16 Color Pattern
NO 16 : Toshiba ABL Pattern
2. Optical measuring device : CA210 (FL)
Please use the MSPG-925 LTH generator for model LE26M51B/LE32M51B/LE40M51B/LE46M51B.
3-4-4 Method of Adjustment
1. Adjust the white balance of AV, Component and DVI Modes.
(AV Component)
a) Set the input to the mode in which the adjustment will be made
(RF DTV PC DVI).
* Input signal - VIDEO Mode : Model #2 (744*484 Mode), Pattern #16
- DTV,DVI Mode : Model #6 (1280*720 Mode), Pattern #16
- HDMI Mode: Model #6(1280*720 Mode), Pattern #16
b) Enter factory color control, confirm the data.
c) Adjust the low light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust sub - Brightness to set the 'Y' value.
- Adjust red offset ('x') and blue offset ('y') to the color coordinates.
Picture 4-2 Toshiba ABL Pattern
Low light
Measurement point
* Do not adjust green offset data.
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
3-10
3 Alignments and Adjustments
d) Adjust the high light. (Refer to table 1, 2 in adjustment position by mode)
- Adjust red gain ('x') and blue gain ('y') to the color coordinates.
* Do not adjust the green gain and sub-contrast (Y) data.
Picture 4-3 Toshiba ABL Pattern
High light
Measurement point
3-11
3 Alignments and Adjustments
3-5 Software Upgrade
3-5-1 How to Update Flash ROM
1. Installthe Flash Downloader
ConnectSet(Service Jack)and Jig Cable to execute Program Update.
2. Flash Downloader program update
-Before Turning on the set,Click "connect"which is under of OSD Screen!
-Turn on the Set.
3-12