Text preview for : imagerunner_advance_715_series.pdf part of canon imageRUNNER 715 / 615 / 525 imageRUNNER ADV 715/615/525 Series
Service Manual
651 Pages
Back to : imagerunner_advance_715_s | Home
Revision 1.0
iR-ADV 715/615/525 Series
Service Manual
Important Notices
Important Notices
Application
This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair
of products.
This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does
not apply to your locality.
Corrections
This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products.
When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the
need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new
edition of this manual.
The following paragraph does not apply to any countries where such provisions are inconsistent with local law.
Trademarks
The product names and company names used in this manual are the registered trademarks of the individual companies.
Copyright
The copyright of this document belongs to Canon Inc. This document may not be copied, reproduced or translated into another
language, in whole or in part, without the prior consent of Canon Inc.
Copyright CANON INC. 2018
Caution
Use of this manual should be strictly supervised to avoid disclosure of confidential information.
Explanation of Symbols
The following symbols are used throughout this Service Manual.
Symbols Explanation Symbols Explanation
Check. Remove the claw.
1x
Check visually. Insert the claw.
1x
Important Notices
Symbols Explanation Symbols Explanation
Check a sound. Push the part.
Disconnect the connector. Connect the power cable.
1x
Connect the connector. Disconnect the power cable.
1x
Remove the cable/wire from the Turn on the power.
cable guide or wire saddle.
1x
Install the cable/wire to the cable Turn off the power.
guide or wire saddle.
1x
Remove the screw. Loosen the screw.
1x 1x
Install the screw. Tighten the screw.
1x 1x
Cleaning is needed. Measurement is needed.
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and
mechanical systems with reference to the timing of operation.
In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol, the arrow
indicates the direction of the electric signal.
The expression "turn on the power" means flipping on the power switch, closing the front door, and closing the delivery unit
door, which results in supplying the machine with power.
2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is "High", while '0' is used to indicate "Low".
(The voltage value, however, differs from circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field. Therefore, the operations
of the microprocessors used in the machines are not discussed: they are explained in terms of from sensors to the input of
the DC controller PCB and from the output of the DC controller PCB to the loads.
The descriptions in this Service Manual are subject to change without notice for product improvement or other purposes, and
major changes will be communicated in the form of Service Information bulletins.
All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant Service
Information bulletins and be able to identify and isolate faults in the machine.
Contents
Contents
Safety Precautions...............................................................................................1
Laser Safety........................................................................................................................................ 2
How to Handle the Laser Scanner Unit............................................................................................... 2
Power Supply...................................................................................................................................... 2
Toner Safety........................................................................................................................................3
About Toner..........................................................................................................................................3
Handling Adhered Toner........................................................................................................................3
Notes When Handling a Lithium Battery............................................................................................. 3
Notes Before it Works Serving............................................................................................................ 3
Points to Note at Cleaning...................................................................................................................4
Notes on Assembly/Disassembly........................................................................................................ 4
1. Product Overview.............................................................................................5
Product Lineup.................................................................................................................................... 6
Host Machine........................................................................................................................................6
Pickup/Delivery / Image Reading System Options................................................................................... 7
Function expansion system options........................................................................................................8
Specifications...................................................................................................................................... 9
Host machine........................................................................................................................................9
Weight and Size..................................................................................................................................10
Paper Type.........................................................................................................................................10
Available Paper Types.........................................................................................................................10
Parts Name....................................................................................................................................... 14
Cross Section View............................................................................................................................. 14
Control Panel......................................................................................................................................15
2. Technology..................................................................................................... 16
Functional Configuration................................................................................................................... 17
Original Exposure System.................................................................................................................18
Features.............................................................................................................................................18
Specifications..................................................................................................................................... 18
Basic Configuration............................................................................................................................. 19
Dust Detection Control.........................................................................................................................23
Image Processing............................................................................................................................... 24
Outline of Electric Circuits....................................................................................................................30
Scanner Unit.......................................................................................................................................30
Pickup Feed System........................................................................................................................... 32
ADF Scan Operation Sequence (Common to 2-sided/1-sided)............................................................... 36
Controller System..............................................................................................................................38
Overview............................................................................................................................................ 38
Startup Sequence............................................................................................................................... 39
Shutdown Sequence........................................................................................................................... 40
Motion Sensor.....................................................................................................................................40
Laser Exposure System.................................................................................................................... 42
i
Contents
Overview............................................................................................................................................ 42
Laser ON/OFF Control.........................................................................................................................42
Scanner Motor Control.........................................................................................................................43
APC (Auto Power Control)................................................................................................................... 43
BD Detection Correction Control.......................................................................................................... 44
Image Formation System.................................................................................................................. 45
Overview............................................................................................................................................ 45
Cartridge............................................................................................................................................ 46
Transfer..............................................................................................................................................48
Image Stabilization Control.................................................................................................................. 49
Fixing System....................................................................................................................................51
Features.............................................................................................................................................51
Fixing temperature control................................................................................................................... 53
Standby Temperature Control.............................................................................................................. 54
Print Temperature Control....................................................................................................................54
Down Sequence Control...................................................................................................................... 55
Pre-fixing Arch Control.........................................................................................................................55
Fixing Film Unit engagement/disengagement control............................................................................. 56
Fixing Assembly detection................................................................................................................... 57
Fixing Assembly Life Detection............................................................................................................ 58
Protection Function............................................................................................................................. 58
Pickup Feed System......................................................................................................................... 60
Overview............................................................................................................................................ 60
Cassette Pickup Assembly...................................................................................................................66
Multi-purpose Tray Pickup Assembly.................................................................................................... 69
Registration Assembly.........................................................................................................................70
Process Tray Assembly (Model with Built-in Finisher Only).................................................................... 70
Stack Tray Assembly (Model with Built-in Finisher Only)........................................................................ 73
Delivery Assembly...............................................................................................................................75
Reverse/Duplex Assembly................................................................................................................... 75
Jam Detection.....................................................................................................................................76
External Auxiliary System..................................................................................................................78
Software Counter Control.................................................................................................................... 78
Location of Fans................................................................................................................................. 80
Power supply...................................................................................................................................... 81
Power-saving Function........................................................................................................................ 81
Quick Startup......................................................................................................................................83
3. Periodical Service.......................................................................................... 85
Periodically Replaced Parts.............................................................................................................. 86
Consumable Parts List...................................................................................................................... 87
Host Machine......................................................................................................................................87
Cassette Module-AG........................................................................................................................... 87
Envelope Cassette Module-A1............................................................................................................. 87
High Capacity Cassette Feeding Unit-D1.............................................................................................. 88
Cassette Feeding Unit-AR1................................................................................................................. 88
4. Parts Replacement and Cleaning................................................................. 89
Preface.............................................................................................................................................. 90
Outline............................................................................................................................................... 90
ii
Contents
Parts List........................................................................................................................................... 91
List of Cover (with Finisher)................................................................................................................. 91
List of Cover (without Finisher).............................................................................................................93
Main Unit............................................................................................................................................ 95
ADF................................................................................................................................................... 97
Reader............................................................................................................................................... 98
PCB................................................................................................................................................... 99
Switch.............................................................................................................................................. 101
Fan.................................................................................................................................................. 103
Motor................................................................................................................................................104
Sensor..............................................................................................................................................105
Motor (with Finisher)..........................................................................................................................106
Sensor (Finisher)...............................................................................................................................107
Others (Finisher)............................................................................................................................... 108
External Cover/Interior System....................................................................................................... 109
Removing the Rear Cover..................................................................................................................109
Removing the Left Rear Cover........................................................................................................... 109
Removing the Front Cover................................................................................................................. 110
Removing the Inlet Cover...................................................................................................................111
Removing the Right Lower Cover....................................................................................................... 111
Removing the Cartridge Door Unit...................................................................................................... 113
Removing the Control Panel...............................................................................................................115
External / Internal Cover System (Finisher).................................................................................... 119
Removing the Finisher Rear Cover.....................................................................................................119
Removing the Finisher Right Upper Cover.......................................................................................... 119
Removing the Finisher Left Rear Cover.............................................................................................. 121
Removing the Finisher Right Rear Cover............................................................................................ 121
Removing the Finisher Right Lower Cover.......................................................................................... 122
Removing the Staple Cover............................................................................................................... 122
Removing the Staple Inner Cover....................................................................................................... 123
Removing the Delivery Tray............................................................................................................... 124
Removing the Inner Delivery Rear Cover............................................................................................ 124
Removing the Finisher Inner Rear Cover............................................................................................ 125
Original Exposure/Feed System......................................................................................................127
Removing the ADF Unit..................................................................................................................... 127
Removing the ADF Pickup Unit.......................................................................................................... 135
Removing the ADF Separation Unit.................................................................................................... 136
Removing the Scanner Unit (Back).....................................................................................................137
Removing the Copyboard Glass Unit.................................................................................................. 144
Removing the Scanner Unit (Front).....................................................................................................145
Removing the Reader Motor.............................................................................................................. 149
Removing the ADF Feed Frame......................................................................................................... 149
Removing the CIS Holder.................................................................................................................. 181
Controller System............................................................................................................................192
Removing the Main Controller Sub Cover /Main Controller Cover......................................................... 192
Removing the HDD........................................................................................................................... 193
Removing the Main Controller PCB.................................................................................................... 193
Removing the Low-Voltage Power Supply PCB................................................................................... 195
Removing the Inlet Unit......................................................................................................................196
Removing the DC Controller PCB.......................................................................................................198
Removing the High-Voltage Power Supply PCB.................................................................................. 198
iii
Contents
Removing the FAX Unit..................................................................................................................... 199
Controller System (Finisher)............................................................................................................203
Removing the Finisher Controller PCB................................................................................................203
Laser Exposure System.................................................................................................................. 204
Removing the Laser Scanner Unit...................................................................................................... 204
Image Formation System................................................................................................................ 205
Removing the Transfer Unit............................................................................................................... 205
Removing the Developing Drive Unit.................................................................................................. 206
Removing the Lifter Drive Unit............................................................................................................209
Removing the Drum Motor Unit.......................................................................................................... 210
Fixing System..................................................................................................................................212
Removing the Fixing Assembly.......................................................................................................... 212
Removing the Fixing Drive Unit.......................................................................................................... 212
Pickup Feed System....................................................................................................................... 214
Removing the Paper Delivery Unit...................................................................................................... 214
Removing the Main Drive Unit............................................................................................................ 215
Removing the Paper Pickup Unit........................................................................................................ 219
Removing the Multi-purpose Tray Feed Roller.....................................................................................222
Removing the Multi-purpose Tray Separation Roller............................................................................ 223
Pickup Feed System (Finisher)....................................................................................................... 225
Removing the Jogger Unit..................................................................................................................225
Removing the Staple Unit.................................................................................................................. 225
Removing the Finisher Fan................................................................................................................ 226
Removing the Finisher Motor............................................................................................................. 227
Upper Paper Feed Unit...................................................................................................................... 227
Lower Paper Feed Unit...................................................................................................................... 229
5. Adjustment................................................................................................... 232
Pickup Feed System....................................................................................................................... 233
Image Position Adjustment.................................................................................................................233
Actions at Parts Replacement......................................................................................................... 235
Hard Disc..........................................................................................................................................235
Main Controller PCB..........................................................................................................................237
DC Controller PCB............................................................................................................................ 237
After Replacing the Copyboard Glass................................................................................................. 238
After Replacing the Scanner Unit (Front).............................................................................................238
After Replacing the Scanner Unit (Back)............................................................................................. 239
After Replacing Touch Panel/Control Panel CPU PCB/LCD Unit.......................................................... 240
6. Troubleshooting...........................................................................................241
Initial Check.....................................................................................................................................242
Initial check items list.........................................................................................................................242
Test Print......................................................................................................................................... 243
Overview.......................................................................................................................................... 243
How to use the test print.................................................................................................................... 244
Debug Log.......................................................................................................................................248
Function Overview.............................................................................................................................248
Saving and Collecting Debug Logs..................................................................................................... 252
Service Mode Relating to Debug Logs................................................................................................ 265
iv
Contents
7. Error/Jam/Alarm........................................................................................... 267
Overview......................................................................................................................................... 268
Location Code...................................................................................................................................268
Pickup Position Code.........................................................................................................................268
Pickup size....................................................................................................................................... 268
Points to Note When Clearing MN-CON .............................................................................................269
Points to Note When Clearing HDD.................................................................................................... 270
Error Code.......................................................................................................................................271
Error Code Details.............................................................................................................................271
Error Code (FAX)............................................................................................................................ 324
How to View Fax Error Codes............................................................................................................ 324
User error codes............................................................................................................................... 324
Service Error Code............................................................................................................................324
Alarm Code..................................................................................................................................... 327
Alarm Code Details........................................................................................................................... 327
Jam Code........................................................................................................................................ 336
Jam Type..........................................................................................................................................336
Jam screen display specification........................................................................................................ 337
Main Unit.......................................................................................................................................... 337
ADF / Reader....................................................................................................................................338
Option Cassette................................................................................................................................ 339
Inner Finisher....................................................................................................................................341
8. Service Mode................................................................................................ 342
Overview......................................................................................................................................... 343
Basic Operations...............................................................................................................................343
SITUATION Mode............................................................................................................................. 346
Security Support................................................................................................................................351
Service Mode Backup........................................................................................................................355
Output of Service Print Data...............................................................................................................355
COPIER (Service mode for printer).................................................................................................360
DISPLAY (State display mode)...........................................................................................................360
I/O....................................................................................................................................................376
ADJUST (Adjustment mode).............................................................................................................. 376
FUNCTION (Operation / inspection mode).......................................................................................... 427
OPTION (Specification setting mode)................................................................................................. 446
TEST (Print test mode)...................................................................................................................... 531
COUNTER (Counter mode)............................................................................................................... 535
FEEDER (ADF service mode).........................................................................................................548
DISPLAY (State display mode)...........................................................................................................548
ADJUST (Adjustment mode).............................................................................................................. 548
FUNCTION (Operation / inspection mode).......................................................................................... 550
OPTION (Specification setting mode)................................................................................................. 551
BOARD (Option board setting mode)..............................................................................................553
OPTION (Specification setting mode)................................................................................................. 553
FAX (Serivce Mode for FAX)...........................................................................................................554
Overview.......................................................................................................................................... 554
Setting of Bit Switch (SSSW)..............................................................................................................557
Setting of Menu Switch (MENU)......................................................................................................... 568
v
Contents
Setting of Numeric Parameter (NUMERIC Param.).............................................................................. 569
Setting of Destination (TYPE).............................................................................................................571
Setting of Printer Functions (PRINTER).............................................................................................. 572
IPFAX Setting................................................................................................................................... 574
Initialization of Set Value (CLEAR)..................................................................................................... 575
Test Mode (TEST).............................................................................................................................575
Service Report (REPORT)................................................................................................................. 579
9. Installation.................................................................................................... 583
How to Utilize This Installation Procedure.......................................................................................584
Symbols........................................................................................................................................... 584
Host Mashine Installation................................................................................................................ 585
Setting the Dehumidification Switch.................................................................................................... 585
Operation when using uniFLOW Online.............................................................................................. 585
IC Card Reader Attachment-A1...................................................................................................... 586
Points to Note at Installation ..............................................................................................................586
Installation Outline Drawing ...............................................................................................................586
Checking the Contents...................................................................................................................... 586
Essential Items to Be Performed Before Installation.............................................................................586
Installation Procedure ....................................................................................................................... 587
NFC Kit-C1 ..................................................................................................................................... 591
Points to Note when Installing ........................................................................................................... 591
Installation Outline Drawing ...............................................................................................................591
Checking the Contents ......................................................................................................................591
Essential Items to Be Performed Before Installation.............................................................................591
Installation procedure ....................................................................................................................... 591
Setting after Installation..................................................................................................................... 600
Copy Card Reader-F1/Copy Card Reader Attachment-B5............................................................. 601
Points to Note when Installing ........................................................................................................... 601
Installation Outline Drawing ...............................................................................................................601
Checking the Contents ......................................................................................................................601
Essential Items to Be Performed Before Installation.............................................................................602
Installation ....................................................................................................................................... 602
Checking after Installation ................................................................................................................. 610
Copy Control Interface Kit-A1 .........................................................................................................612
Installation Outline Drawing ...............................................................................................................612
Checking the Contents ......................................................................................................................612
Essential Items to Be Performed Before Installation.............................................................................612
Installation Procedure........................................................................................................................ 613
Connection Kit-A1 for Bluetooth LE.................................................................................................616
Points to Note at Installation ..............................................................................................................616
Installation Outline Drawing................................................................................................................616
Essential Items to Be Performed Before Installation.............................................................................616
Checking the Contents...................................................................................................................... 616
Installation Procedure ....................................................................................................................... 616
Setting after Installation..................................................................................................................... 619
Super G3 FAX Board-AY1.............................................................................................................. 620
Checking before Installation............................................................................................................... 620
Installation Procedure........................................................................................................................ 621
Checking the Operation..................................................................................................................... 627
vi
Contents
APPENDICES....................................................................................................628
Service Tools...................................................................................................................................629
Special Tools.................................................................................................................................... 629
Solvents and Oils.............................................................................................................................. 629
General Circuit Diagram..................................................................................................................630
Host machine 1/5.............................................................................................................................. 630
Host machine 2/5.............................................................................................................................. 631
Host machine 3/5.............................................................................................................................. 632
Host machine 4/5.............................................................................................................................. 633
Host machine 5/5.............................................................................................................................. 634
Soft counter specifications.............................................................................................................. 635
Software Counter Specifications.........................................................................................................635
Removal.......................................................................................................................................... 639
Overview.......................................................................................................................................... 639
Work Procedure................................................................................................................................ 639
vii
Safety Precautions
Laser Safety.......................................... 2
How to Handle the Laser Scanner Unit
...........................................................2
Power Supply........................................ 2
Toner Safety..........................................3
Notes When Handling a Lithium
Battery............................................... 3
Notes Before it Works Serving.............. 3
Points to Note at Cleaning.................... 4
Notes on Assembly/Disassembly..........4
Safety Precautions
Laser Safety
Since radiation emitted inside this machine is completely confined with protective housings and external covers, the laser beam
cannot escape from the machine during any phase of normal use by users.
Therefore, this machine is classified as a Class 1 laser product under the international standard IEC60825-1 that is regarded as
safe during normal use.
How to Handle the Laser Scanner Unit
This machine is classified as a Class 1 laser product.
However, the laser scanner unit contains source of Class 3B laser beam and exposure to the beam may cause eye injuries.
Therefore, be sure not to disassemble the laser scanner unit. No adjustment can be made to the laser scanner unit in the machine
in the field.
The mark or the warning label shown in the following figure is affixed on the laser scanner unit.
Dieses Gerät ist der Klasse 1 der Laserprodukte zugeordnet.
Allerdings enthält die Laserscannereinheit eine Laserstrahlquelle der Klasse 3B, die Augenschäden verursachen kann, wenn
man in diesen Strahl blickt.
Deshalb darf die Laserscannereinheit nicht zerlegt werden. An der Laserscannereinheit kann keine Justage vor Ort vorgenommen
werden.
Das in dem folgenden Bild dargestellte Kennzeichen bzw. der Warnaufkleber ist auf der Laserscannereinheit angebracht.
Power Supply
· As a general rule, do not use extension cords.
If an extension cord must be used, however, use one for local rated voltage and over, untie the cord binding, and insert the
power plug completely into the extension cord outlet to ensure a firm connection between the power cord and the extension
cord.
CAUTION:
Do not plug multiple cords together to an extension cord. It may cause a fire or electrical shock.
· The socket-outlet shall be installed near the equipment and shall be easily accessible.
2
Safety Precautions
Toner Safety
About Toner
Toner is a nontoxic matter composed of plastic, iron and a trace of pigments.
CAUTION:
Never throw toner in flames to avoid explosion.
Handling Adhered Toner
· Use dry tissue paper to wipe off toner adhered to skin or clothes and wash in water.
· Never use warm water for cleaning up toner to prevent toner particles from being gelated to soak into fibers permanently.
· Toner particles are reactive with vinyl polymers. Avoid contacting these materials.
Notes When Handling a Lithium Battery
Dispose of used batteries according to the instructions.
CAUTION:
Risk of explosion if battery is replaced by an incorrect type.
The following warnings are given to comply with Safety Principles (EN60950-1).
CAUTION:
Wenn mit dem falschen Typ ausgewechselt, besteht Explosionsgefahr.
Gebrauchte Batterien gemäß der Anleitung beseitigen.
Notes Before it Works Serving
· At servicing, be sure to turn OFF the power source according to the specified steps and disconnect the power plug.
· Be sure to disconnect the power plug on a regular basis and remove dust and dirt accumulated around the outlet with dry
cloth.
CAUTION:
Leaving the power plug connected for a long time in an environment having a lot of dust, moisture, or oily smoke will
cause a fire. (Because dust accumulated in the surrounding area will absorb moisture and cause an insulation failure)
3
Safety Precautions
Points to Note at Cleaning
When performing cleaning using organic solvent such as alcohol, be sure to check that the component of solvent is vaporized
completely before assembling.
Notes on Assembly/Disassembly
Follow the items below to assemble/disassemble the device.
1. Disconnect the power plug to avoid any potential dangers during assembling/disassembling works.
2. If not specially instructed, reverse the order of disassembly to reinstall.
3. Ensure to use the right screw type (length, diameter, etc.) at the right position when assembling.
4. To keep electric conduction, binding screws with washers are used to attach the grounding wire and the varistor. Ensure to
use the right screw type when assembling.
5. Unless it is specially needed, do not operate the device with some parts removed.
6. Never remove the paint-locked screws when disassembling.
CAUTION:
English
CAUTION
The fuse may be in the neutral, and that the mains shall be disconnected to de-energize the phase conductors.
German
VORSICHT
Die Sicherung kann sich im Nullleiter befinden und das Hauptnetz muss abgetrennt werden, um die Phasenleiter
stromlos zu machen.
4
1 Product Overview
Product Lineup...................................... 6
Specifications........................................ 9
Parts Name......................................... 14
1. Product Overview
Product Lineup
Host Machine
Product name
imageRUNNER ADVANCE 715 / 615 / 525
The underlined numerical value indicates the print speed (ppm: page per minute).
Model 715I / 615I / 525I 715IF / 615IF / 525IF 715IFZ / 615IFZ / 715IZ / 615IZ / 525IZ
525IFZ
Print speed 71 ppm , 61 ppm , 52 ppm
Reader Equipped as standard
ADF Equipped as standard
Inner Finisher - Equipped as standard
Cassette Equipped as standard (Cassette 1), Optional (Cassette 2/3/4)
HDD Equipped as standard
1-line FAX - Equipped as standard -
F : with FAX model
Z : with Inner Finisher model
6
1. Product Overview
Pickup/Delivery / Image Reading System Options
[1]
[2]
[3]
[4]
[5]
No. Product name
1 ADF Access Handle-A1
2 Cassette Module-AG1
3 Envelope Cassette Module-A1
4 High Capacity Cassette Feeding Unit-D1
5 Cassette Feeding Unit-AR1
7
1. Product Overview
Function expansion system options
[6]
[1]
[3]
[8]
[2]
[9]
[4]
[10]
[7]
No. Product name
1 NFC Kit-C1
2 Copy Card Reader Attachment-B5
3 Copy Card Reader-F1
4 Copy Control Interface Kit-A1
5 IC Card Reader Box-D1
6 IC Card Reader Attachment-A1
7 Super G3 FAX Board-AY1
8 Connection Kit-A1 for Bluetooth LE
9 Power Supply Cable-V1
10 Remote Fax Kit-A1
IP FAX Expansion Kit-B1
PCL International Font Set-A1
Picture Login-A1
Barcode Printing Kit-D1
Universal Send Trace & Smooth PDF Kit-A1
Universal Send Advanced Feature Set-H1
Universal Send Digital User Signature Kit-C1
8
1. Product Overview
Specifications
Host machine
Item Specifications
Machine installation Desk-top
method
Photosensitive medium 30mm, OPC
Exposure method Semiconductor 4Beam Laser
Charging method DC Roller Charging
Developing method Dry, 1-component toner projection development
Transfer method Roller Transfer
Separation method Retard separation method without driving source
Pickup method Stack bypass : Retard separation method
Cassette : Retard separation method
Fixing method On demand fixing
Drum cleaning method Cleaning Blade
Toner type 1-component
oner supplying method ALL in one Cartridege
Toner level detection Yes
function
Leading edge image 5.0mm +/-2.0mm
margin
Left image margin Left Side : 2.5 +/- 1.5 ( duplex : 2.5 +/- 2.0 )
Image gradations 256 Gradation Levels
Print resolution 9600 dpi ( equivalent ) x 600 dpi ( at 600dpi mode ) T.B.D.
1200 dpi x 1200 dpi ( equivalent ) ( at 1200dpi mode ) T.B.D.
Maximum image guar- 205.9 x 345.6 mm T.B.D.
antee area
Maximum printable area 209.4 x 348.1 mm T.B.D.
Warm-up time After Powering ON :
( Time from device pow- [Quick Startup Settings for Main Power] OFF: 30 sec. or less
er on, until copy ready ) [Quick Startup Settings for Main Power] ON: 4 sec. or less (This may vary depending on the usage envi-
ronment and usage conditions.)
Returning from the Sleep mode :
[Sleep Mode Eco Exit] OFF (default): 10 sec. or less
[Sleep Mode Eco Exit] ON: 15 sec. or less (reference value)
First copy time 5.0 sec ( 20 deg C to 30 deg C Environment )
Paper type / Paper Size Refer to "Available Paper Types" on page 10
Pickup capacity Stack bypass :
100 sheets(75/80 g/m 2)
10 sheets(Envelope)
Cassette :
550 sheets (75/80 g/m 2)
Memory capacity RAM : 3GB
Main CPU Side : 2GB
Image Processing CPU Side : 1GB
Hard disk capacity HDD : more than 250GB ( Avairable disk space 250GB. A different hard disc drive may be used. )
Rated power supply 120 to 127V 60Hz T.B.D. A
110 to 127V 60Hz T.B.D. A
220 to 240V 50/60Hz T.B.D. A
9
1. Product Overview
Item Specifications
Power consumption Max. power consumption :1500W or less
(reference value) Average power consumption while copying/printing ( measusred only one machine ( Reference ) while ADF
copying ): T.B.D. Wh
Average power consumption at sandby mode ( measusred only one machine ( Reference )) : T.B.D. Wh
Power consumptgion at sleep mode :
· Low energy consumption during sleep mode : TBD Wh
· High energy consumption during sleep mode : TBD Wh
Low energy consumption during sleep mode + Network connection is considered (measusred only one ma-
chine (reference value))
120V: TBD W
230V: TBD W
Dimensions / Weight Refer to "Weight and Size" on page 10
Weight and Size
Product name Width (mm) Depth (mm) Height (mm) Weight: Ap-
prox. (kg)
imageRUNNER ADVANCE 715 I / 615 I / 525 I 513 601 (with Control 617 33.5 *1
imageRUNNER ADVANCE 715 IF / 615 IF / 525 IF Panel) 34.0 *1
imageRUNNER ADVANCE 715 IFZ / 615IFZ / 525IFZ 515 (with Finish- 814 43.0 *1
imageRUNNER ADVANCE 715 IZ / 615I