Text preview for : 2LW-003.pdf part of Kyocera 2LW-003 Kyocera Printer FS-3040-3140MFP SERVICEBULLETIN 2LW-003.pdf
Back to : 2LW-003.pdf | Home
Service Bulletin
SB Number: SB 2LW-003 Creation Date: 15/09/2010
Subject: Firmware upgrade
Model: FS-3040MFP/3140MFP
Item Contents
1 Adjusting the scanner command. The setup parameter to adjust the scanner command has been added.
2 Clearing the click charge/machine Maintenance mode U927 has been added to clear the click charge and the
life count. machine life count.
3 Error code F145. Error code F145 may occur, when receiving information 100 times or more
via URDS.
Firmware
Type Program No. Check SUM Version Status Date Applicable models
ENGINE 2LW_1000.002.001 c43f 002.001 04/06/2010 FS-3040MFP/3140MFP
MAIN 2LW_2F00.004.003 ---- 004.003 ---------- FS-3040MFP
MAIN 2LX_2F00.004.003 ---- 004.003 ---------- FS-3140MFP
FAX 2H9_54000003003 ---- ------- ---------- FS-3140MFP
Classification Entire stock rework In-field modification at next visit In-field modification by case No modification necessary
Field measure Please upgrade the firmware to the latest version to implement the above mentioned changes.
Serial numbers of affected machines
Type Serial number
FS-3040MFP/3140MFP August 2010 production.
The above mentioned changes have been applied to machines produced after the above mentioned production date.
Item 1: Adjusting the scanner command. (Command and parameter)
KCFG "SCAN", #1[ ,#2, #3]
Adjusting the DP scanning timing
#1 Set item 2 DP scanning timing
#2 Set target Value Refer to set target below
#3 Input value
Adjusting the DP center line
#1 Set item 3 DP center line
#2 Set target Value Refer to set target below
#3 Input value
Adjusting the DP magnification
#1 Set item 4 DP magnification
#2 Set target Value Refer to set target below
#3 Input value
KMIS Service Department, Kyocera Mita Europe Page of 2 A288 / SB 2LW-003
Service Bulletin
Adjusting the scanner leading edge
#1 Set item 5 Scanner leading edge
#2 Set target Value Refer to set target below
#3 Input value
Adjusting the scanner center line
#1 Set item 6 Scanner center line
#2 Set target Value Refer to set target below
#3 Input value
Adjusting the scanner magnification
#1 Set item 8 Scanner magnification
#2 Set target Value Refer to set target below
#3 Input value
Adjusting the scanner center line DP
#1 Set item 9 DP scanning position
#2 Set target Value Refer to set target below
#3 Input value
Item 1: Corresponding maintenance mode number and set target.
#1 Number Item #2 Name Min Max
2 U071 Adjusting the DP scanning timing 1 Front head -32 32
2 Front tail -32 32
3 Back head -45 45
4 Back tail -45 45
5 180 degree rotated -128 127
3 U072 Adjusting the DP center line 1 DP center line (Data1) -39 39
2 DP center line (Data1) -39 39
3 DP center line (Data1) -39 39
4 U070 Adjusting the DP magnification 2 DP magnification -25 25
5 U066 Adjusting the scanner leading edge 1 Table leading edge (Data1) -45 45
registration 2 Table leading edge (Data1) -45 45
6 U067 Adjusting the scanner center line 1 Table center line (Data1) -70 70
2 Table center line (Data1) -40 40
8 U065 Adjusting the scanner center line 1 Y scan zoom (Main) -32 127
2 X scan zoom (Sub) -25 25
9 U068 Adjusting the scanning position originals 1 DP read (Dat1) -33 33
from the DP read/DP back 2 DP back line (Test pos) 0 3
KMIS Service Department, Kyocera Mita Europe Page 2 of 2 A288 / SB 2LW-003