Text preview for : MVT2135BSM.pdf part of Memorex MVT2135B Series D Service Manual Color Monitor - (5.493Kb) pag. 132
Back to : combi_tv_vcr.part1.rar | Home
MVT2135B SERIES D
SERVICE MANUAL
COLOR TELEVISION/VIDEO CASSETTE RECORDER
ORIGINAL MFR'S VERSION A
Design and specifications are subject to change without notice.
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an electric shock while the electric current is flowing.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.
7. PERFORM A SAFETY CHECK AFTER SERVICING
Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal Earphone jack
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in youCr SERVICE MANUAL.
A1-1
CONTENTS
SERVICING NOTICES ON CHECKING .................................................................................. HOW TO ORDER PARTS ....................................................................................................... CONTENTS ................................................................................................................................. GENERAL SPECIFICATIONS .................................................................................................... DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS ............................................ 2. REMOVAL OF DECK PARTS ............................................................................................ 3. REMOVAL OF ANODE CAP .............................................................................................. 4. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ................................................. KEY TO ABBREVIATIONS ..................................................................................................... SERVICE MODE LIST ............................................................................................................ PREVENTIVE CHECKS AND SERVICE INTERVALS ............................................................ WHEN REPLACING EEPROM (MEMORY) IC ..................................................................... SERVICING FIXTURES AND TOOLS ..................................................................................... PREPARATION FOR SERVICING ......................................................................................... MECHANICAL ADJUSTMENTS ............................................................................................. ELECTRICAL ADJUSTMENTS ............................................................................................... BLOCK DIAGRAMS TV ............................................................................................................................................ Y/C/AUDIO/CCD/HEAD AMP/IN/OUT .................................................................................... MICON/OPERATION............................................................................................................... PRINTED CIRCUIT BOARDS OPERATION ............................................................................................................................ SYSCON/CRT ......................................................................................................................... SCHEMATIC DIAGRAMS Y/C/AUDIO/CCD/HEAD AMP ................................................................................................. MICON ..................................................................................................................................... IN/OUT ..................................................................................................................................... CHROMA/IF ............................................................................................................................. SOUND AMP ........................................................................................................................... POWER ................................................................................................................................... DEFLECTION .......................................................................................................................... CRT .......................................................................................................................................... OPERATION ........................................................................................................................... INTERCONNECTION DIAGRAM ............................................................................................ WAVEFORMS ............................................................................................................................. MECHANICAL EXPLODED VIEWS ........................................................................................... CHASSIS EXPLODED VIEWS ................................................................................................... MECHANICAL REPLACEMENT PARTS LIST ......................................................................... CHASSIS REPLACEMENT PARTS LIST .................................................................................. ELECTRICAL REPLACEMENT PARTS LIST ........................................................................
A1-1 A1-1 A2-1 A3-1~A3-4 B1-1 B2-1~B2-5 B3-1 B4-1, B4-2 C1-1, C1-2 C2-1 C3-1, C3-2 C4-1 C5-1 C5-1 D1-1~D1-4 D2-1~D2-5 E-1, E-2 E-3, E-4 E-5, E-6 F-1, F-2 F-3~F-6 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 G-9, G-10 G-11, G-12 G-13, G-14 G-15, G-16 G-17, G-18 G-19, G-20 H-1, H-2 I-1, I-2 I-3, I-4 J1-1 J2-1 J3-1, J3-2
A2-1
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 13 inch / 335.4 mmV Normal 90 degree +0.45G / +0.18G NTSC 1Speaker Front 1.5 x 2.5 Inch 8 ohm 1.5 W 1.0 W VHS Player / Recorder NTSC No OVD-7 Front 3 2Head No Mono /Yes Yes SP/SLP SP/LP/SLP FF:4'50"/REW:2'30" T-120 SP/LP/SLP=3x,5x/7x,9x/9x,15x US System M 1Tuner US(w/CATV) F-Synth VHF/UHF 75 ohm 2~69, 4A,A-5~A-1, A~I, J~W,W+1~W+84 45.75 MHz 41.25 MHz 4.5 MHz No No Yes 1 V p-p/75 ohm 50dB 220Lines -8dBm/50Kohm 38dB 1.5 % 100Hz - 10kHz 100Hz - 6kHz 100Hz - 4kHz dB %Wrms dB % 120V,60Hz 65 W at 120V 60Hz 5 W at 120V 60Hz Yes No UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less then 80% RH Yes
Color System Speaker Position Size Impedance MAX 10%(Typical)
Sound Output G-2 VCR System System Video System Hi-Fi STEREO NTSC PB Deck
DECK Loading System Motor Video Head FM Audio Head
Heads
Audio /Control Erase(Full Track Erase) Tape Rec PAL Speed NTSC Play PAL NTSC Fast Forward / Rewind Time (Approx.) with Cassette Forward/Reverse Picture Search Frame Advance Slow Speed Broadcasting System Tuner and Receive CH NTSC or PAL-M
G-3
Tuning System
System Destination Tuning System Input Impedance CH Coverage
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Video Signal
Picture(FP) Sound(FS) FP-FS
G-4
Signal
Audio Signal
Input Level Output Level S/N Ratio (Weighted) Horizontal Resolution at SP Mode Input Level Output Level S/N Ratio at SP (Weighted) Harmonic Distortion at SP (1KHz) Frequency Response
Typical at SP at LP at SLP
Hi-Fi Audio Signal
G-5
Power
Power Source Power Consumption
Dynamic Range : More than Wow And Flutter : Less than Channel Separation : More than Harmonic Distortion : Less than AC DC at AC at DC Stand by (at AC) Per Year Power Fuse Dew Sensor Safety Radiation X-Radiation Operation Storage
Protector G-6 Regulation
G-7 G-8 G-9
Temperature Operating Humidity On Screen Menu
A3-1
GENERAL SPECIFICATIONS
Display Menu Type Timer Rec Set Channel Setup TV/CATV Auto CH Memory Add/ Delete Guide CH Set TV Setup V-chip Set On/Off Timer Set Picture Audio Sap On/Off Auto Repeat On/Off System Setup Clock Set Language Auto Clock On/Off Standard Time Daylight Saving Time Commercial Advance Marking On/Off Blueback On/Off Playback Auto/Manual Unmarked Tape Movie Advance Go To Movie Go To Preview G-CODE(or SHOWVIEW or PLUSCODE)No. Entry Clock / Date CH/AV Tape Counter(Linear Counter) Tape Speed Sleep Time Stereo/Audio Output Bilingal SAP Control Volume Level Bright / Contrast / Sharpness / Color Tint Bass/Treble/Balance Manual Tracking Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In Auto Tracking/Manual Tracking Caption / Text Index Muting Hi-Fi Repeat Zero Return DEW Charactor Yes Yes Yes Yes Yes No Yes Yes Yes Yes No No Yes Yes Yes Yes Yes Yes Yes No No No No No No No No No Yes Yes Yes Yes Yes No No No Yes Yes Yes No (Symbol Mark) Yes Yes Yes Yes No Yes No Yes No No English French Spanish English 1990/1/1 ~ 2081/12/31 8 Program/ 1 Month 5 Hours No 120 Min 10 Min 1 Program 15 Min 5 Sec RC-CG Yes 3V UM-4 x 2 pcs 41 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes
G-10 G-11
OSD Language Clock,Timer and Timer Back-up OSD Language Setting Calendar Timer Events One Touch Recording Max Time OTPB Valid Time Sleep Timer Max Time Step On/Off Timer Program(On Timer / Off Timer) Auto Shut Off No Signal No Operation Timer Back-up (at Power Off Mode) Unit Glow in Dark Remocon Power Source Voltage(D.C) UM size x pcs Total Keys Keys Power 1 2 3 4 5 6 7 8
G-12
Remote Control
A3-2
GENERAL SPECIFICATIONS
9 0 CH Up CH Down Volume Up Volume Down Input Select Play F.Fwd Rew Pause/Still Stop Rec/OTR Eject Counter Reset Speed Timer Rec TV Monitor Quick View Program Slow Auto Tracking Set/Tracking+ Set/Tracking Menu Enter Cancel Call TV/Caption/Text Sleep Timer Muting Zero Return CM Skip Audio Select G-13 Features Auto Head Cleaning Auto Tracking HQ (VHS Standard High Quality) Auto Power On, Auto Play, Auto Rewind, Auto Eject VIDEO PLUS+(SHOWVIEW,G-CODE) Auto Clock Forward / Reverse Picture Search Reverse Slow One Touch Playback Auto CH Memory Closed Caption TV Auto Shut off Function End Call Index Search SQPB CATV CM Skip(30sec x 6 Times) Comb Filter TV Monitor Program Extend Choke Coil Energy Star Protect of FBT Leak Curcuit Dirty Head V-chip USA V-chip CANADA V-chip Zero Return CM Advance Movie Advance Owner's Manual Language w/Guarantee Card Remote Control Unit Battery UM size x pcs Rod Antenna Poles Terminal w/300 ohm to 75 ohm Antenna Adapter Loop Antenna Terminal U/V Mixer 300 ohm to 75 ohm Antenna Adapter No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes No Yes Yes No No Yes Yes Yes No No No Yes Yes No Yes No No Yes No No Yes No Yes No No English/Spanish No Yes No Yes 2 pole F type Yes No
G-14
Accessories
A3-3
GENERAL SPECIFICATIONS
Antenna Change Plug DC Car Cord (Center+) AC Plug Adapter AC Cord AV Cord (2Pin-1Pin) Guarantee Card Registration Card ESP Card Warning Sheet Dew/AHC Caution Sheet Quick Set-up Sheet Circuit Diagram Service Facility List Important Safeguard Informatin Sheet Switch No No No No No Yes No No No No No No No No No Power Play Pause/Still System Select One Touch Playback Channel Up Channel Down F.FWD/Cue Eject/Stop Main Power SW Volume Up Volume Down Rew/Rev Rec/OTR Input Select Power Rec/OTR T-Rec On Timer CS Rec/OTR One Touch Playback Play Video Input Audio Input Other Terminal Video Input Audio Input Video Output Audio Output Euro Scart Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Inlet Approx. Net (Approx.) Gross (Approx.) Yes Yes No No No Yes Yes Yes Yes No Yes Yes Yes Yes No No Red Red No No No No No RCA x 1 RCA x 1 Head Phone(Stereo & Mono, 3.5mm) No No No No No No W Im No No F Type No 362 x 370.5 x 382 11.0 (24.3 lbs) 12.5 (27.6 lbs) No Yes Double/White 423 x 447 x 443 As per Buyer's Yes 1 Corner / 3 Edges / 6 Surfaces 62 700 Sets PS 94V0/DECABROM PS 94V0/DECABROM
G-15
Interface
Indicator
Key Light up
Terminals
Front
Rear
G-16 G-17 G-18
Set Size Weight Carton Master Carton
W x D x H (mm)
Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test Natural Dropping At Height (cm) Container Stuffing(40' container) Cabinet Front Cabinet Rear
G-19
Cabinet Material
A3-4
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS
1-1: BACK CABINET (Refer to Fig. 1-1) 1. Remove the 4 screws 1. 2. Remove the screw 2. 3. Remove the AC cord from the AC cord hook 3. 4. Remove the Back Cabinet in the direction of arrow.
Front Cabinet
1-3: TV/VCR BLOCK (Refer to Fig. 1-3) 1. Remove the 2 screws 1. 2. Disconnect the following connectors: (CP757, CP353, CP401 and CP502). 3. Unlock the support 2. 4. Remove the TV/VCR Block in the direction of arrow.
Front Cabinet
1 1
1 1 2
UP TO RELEASE TV/VCR Block
2 1 3 1
Fig. 1-3
Back Cabinet
1-4: DECK CHASSIS AND SYSCON PCB (Refer to Fig. 1-4) Fig. 1-1 1. Remove the screw 1. 2. Remove the screw 2. 3. Remove the screw 3. 4. Remove the 3 screws 4. 5. Disconnect the following connectors: (CP1004, CP1005, CP1006, CP4001, CP4002 and CP4003). 6. Remove the Deck Chassis and Deck Shield Plate in the direction of arrow (A). 7. Remove the screw 5. 8. Remove the Syscon PCB in the direction of arrow (B).
1 3
1-2: CRT PCB (Refer to Fig. 1-2) CAUTION: BEFORE REMOVING THE ANODE CAP, DISCHARGE ELECTRICITY BECAUSE IT CONTAINS HIGH VOLTAGE. BEFORE ATTEMPTING TO REMOVE OR REPAIR ANY PCB, UNPLUG THE POWER CORD FROM THE AC SOURCE. 1. Remove the Anode Cap. (Refer to REMOVAL OF ANODE CAP) 2. Disconnect the following connectors: (CP801 and CP851). 3. Remove the CRT PCB in the direction of arrow.
CRT PCB Front Cabinet
2 4 4 4
Deck Shield Plate
Deck Chassis
(A) Syscon PCB
5
Fig. 1-2
(B)
Deck Holder
Fig. 1-4 B1-1
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF DECK PARTS
2-1: TOP BRACKET (Refer to Fig. 2-1) 1. Extend the 2 supports 1. 2. Slide the 2 supports 2 and remove the Top Bracket. NOTE 1. After the installation of the Top Bracket, bend the support 1 so that the Top Bracket is fixed.
Locker R Top Bracket Cassette Side R Check if these positions are locked.
NOTE 1. In case of the Locker R installation, check if the two positions of Fig.2-3-B are correctly locked. 2. When you install the Cassette Side R, be sure to move the Locker R after installing.
1
1
Top Bracket
2
Fig. 2-3-B
2
Main Chassis
2-4: LINK UNIT (Refer to Fig. 2-4)
Main Chassis
Fig. 2-1 2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2) 1. Move the Cassette Holder Ass'y to the front side. 2. Push the Locker R to remove the Cassette Side R. 3. Remove the Cassette Side L.
Cassette Side R Main Chassis Locker R
1. Set the Link Unit to the Eject position. 2. Unlock the support 1. 3. Remove the (A) side of the Link Unit first, then remove the (B) side.
Main Chassis
Link Unit
(A)
(B) Link Unit
1
Main Chassis
Fig. 2-4
Link Ass'y Cassette Side L Main Chassis
2-5: LINK LEVER/FLAP LEVER (Refer to Fig. 2-5) 1. Remove the Link Lever. 2. Remove the Flap Lever.
Fig. 2-2 2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A) 1. Remove the Locker Spring. 2. Unlock the 4 supports 1 and then remove the Cassette Side L/R. 3. Unlock the support 2 and then remove the Locker R.
Locker Spring
Flap Lever
1 1 2
Cassette Holder
Link Lever
Fig. 2-5
Locker R
1 1
Cassette Side R
Cassette Side L
Fig. 2-3-A B2-1
DISASSEMBLY INSTRUCTIONS
2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A) 1. Remove the screw 1. 2. Remove the Loading Motor. 3. Remove the Worm.
Tension Connect
1
Tension Band
1 3
Tension Spring Loading Motor Tension Holder
Tension Arm Ass'y
2 4
Worm Main Chassis
Fig. 2-7-B
· Screw Torque: 3 ± 0.5kgf·cm
1
Fig. 2-6-A
NOTE 1. In case of the Tension Band installation, note the direction of the installation. (Refer to Fig. 2-7-C) 2. In case of the Tension Band installation, install correctly as Fig. 2-7-D. 3. In case of the Tension Connect installation, install as the circled section of Fig. 2-7-E.
NOTE 1. In case of the Worm installation, check if the value of the Fig. 2-6-B is correct.
19.2 ± 0.1mm
Tension Band Tension Connect
Fig. 2-7-C
Safety surface for pressing of the insert.
Fig. 2-6-B [OK]
Tension Connect Tension Band Tension Connect Tension Band
2-7: TENSION ASS'Y (Refer to Fig. 2-7-B) 1. Turn the Pinch Roller Cam clockwise so that the Tension Holder hook is set to the position of Fig. 2-7-A to move the Tension Arm Ass'y. 2. Remove the Tension Spring. 3. Unlock the 2 supports 1 and remove the Tension Band. 4. Unlock the support 2 and remove the Tension Arm Ass'y. 5. Unlock the support 3 and remove the Tension Connect. 6. Float the hook 4 and turn it clockwise then remove the Tension Holder.
Tension Arm Ass'y
[NG]
Fig. 2-7-D
Tension Connect
Main Chassis
Fig. 2-7-E
Fig. 2-7-A
B2-2
DISASSEMBLY INSTRUCTIONS
2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A) 1. Remove the T Brake Spring. 2. Turn the T Brake Arm clockwise and bend the hook section to remove it. 3. Unlock the 2 supports 1 and remove the T Brake Band.
T Brake Band Idler Gear Idler Arm Ass'y S Reel
(A)
T Reel
Hook section
1
T Brake Arm T Brake Spring (A)
1 1
1
Fig. 2-8-A NOTE 1. In case of the T Brake Band installation, install correctly as Fig. 2-8-B. [OK]
T Brake Band T Brake Arm
Fig. 2-9-A NOTE 1. In case of the S Reel and T Reel installation, check if the correct parts are installed. (Refer to Fig. 2-9-B) 2. In case of the Idler Arm Ass'y installation, install correctly as Fig. 2-9-C.
[NG]
T Brake Band
T Brake Arm
Fig. 2-8-B 2-9: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR (Refer to Fig. 2-9-A) 1. Remove the S Reel and T Reel. 2. Remove the 2 Polyslider Washers 1. 3. Remove the Idler Arm Ass'y and Idler Gear. NOTE 1. Take care not to damage the gears of the S Reel and T Reel. 2. The Polyslider Washer may be remained on the back of the reel. 3. Take care not to damage the shaft. 4. Do not touch the section "A" of S Reel and T Reel. (Use gloves.) (Refer to Fig. 2-9-A) Do not adhere the stains on it. 5. When you install the reel, clean the shaft and grease it (MG-33). (If you do not grease, noise may be heard in FF/REW mode.) 6. After installing the reel, adjust the height of the reel. (Refer to MECHANICAL ADJUSTMENT) [NG]
Idler Arm Ass'y Clutch Gear Big Hole (S Reel) Small Hole (T Reel)
Fig. 2-9-B
[OK]
Clutch Gear Idler Arm Ass'y
Fig. 2-9-C
B2-3
DISASSEMBLY INSTRUCTIONS
2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/ P5 ARM ASS'Y (Refer to Fig. 2-10-A) 1. Unlock the support 1 and remove the Cassette Opener. 2. Remove the Pinch Roller Block and P5 Arm Ass'y.
Cassette Opener (1) (3)
2 2
(2)
2
A/C Head
1
A/C Head Spring
Pinch Roller Block
1
A/C Head Base P5 Arm Ass'y · Screw Torque: 5 ± 0.5kgf·cm (Screw 1) Main Chassis
Fig. 2-11-A
Fig. 2-10-A NOTE
Spring Position
1. Do not touch the Pinch Roller. (Use gloves.) 2. In case of the Pinch Roller Block and the Pinch Roller Cam installation, install correctly as Fig. 2-10-B.
Fig. 2-11-B
2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12) 1. Remove the screw 1. 2. Remove the FE Head.
Pinch Roller Block
Can be seen the hole of the Pinch Roller Cam. FE Head
1
P5 Arm Ass'y
Can be seen the hole of the Main Cam.
Fig. 2-10-B
2-11: A/C HEAD (Refer to Fig. 2-11-A) 1. 2. 3. 4. Remove the screw 1. Remove the A/C Head Base. Remove the 3 screws 2. Remove the A/C Head and A/C Head Spring.
· Screw Torque: 5 ± 0.5kgf·cm · The FE Head is not installed on the Video Cassette Player.
Fig. 2-12
NOTE 1. Do not touch the A/C Head. (Use gloves.) 2. When you install the A/C Head Spring, install as shown in Fig. 2-11-B. 3. When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3).
B2-4
DISASSEMBLY INSTRUCTIONS
2-13: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-13) 1. Unlock the support 1 and remove the AHC Ass'y. 2. Disconnect the following connector: (CD2001) 3. Remove the 3 screws 2. 4. Remove the Cylinder Unit Ass'y. NOTE 1. When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction.
2
Pinch Roller Cam
2-15: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR (Refer to Fig. 2-15-A) 1. Remove the E-Ring 1, then remove the Main Cam. 2. Remove the E-Ring 2, then remove the Pinch Roller Cam and Joint Gear.
1
Main Cam
Joint Gear
Cylinder Unit Ass'y
AHC Ass'y
1
Fig. 2-15-A NOTE 1. In case of the Pinch Roller Cam and Main Cam installation, install them as the circled section of Fig. 215-B so that the each markers are met. (Refer to Fig. 2-15-B) Fig. 2-13
Pinch Roller Cam
(3) (2) (1)
2 2
2
· Screw Torque: 3 ± 0.5kgf·cm
2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14)
Marker
1. Remove the Capstan Belt. 2. Remove the 3 screws 1. 3. Remove the Capstan DD Unit.
Main Cam
Capstan Belt Capstan DD Unit
Fig. 2-15-B 2-16: LOADING GEAR S/T ASS'Y (Refer to Fig. 2-16-A) 1. Remove the E-Ring 1 and remove the Main Loading Gear. 2. Remove the Main Rod, Tension Lever, Loading Arm S Ass'y and Loading Arm T Ass'y.
1
1
· Screw Torque: 4 ± 0.5kgf·cm
1 1
Main Rod
Main Loading Gear
Fig. 2-14
Loading Arm T Ass'y Tension Lever
Loading Arm S Ass'y
Fig. 2-16-A B2-5
DISASSEMBLY INSTRUCTIONS
NOTE 1. When you install the Loading Arm S Ass'y, Loading Arm T Ass'y and Main Loading Gear, align each marker. (Refer to Fig. 2-16-B)
Marker
2-18: CASSETTE GUIDE POST/INCLINED BASE S/T UNIT/P4 CAP (Refer to Fig. 2-18-A) 1. Remove the P4 Cap. 2. Unlock the support 1 and remove the Cassette Guide Post. 3. Remove the Inclined Base S Unit and Inclined Base T Unit.
Cassette Guide Post
Main Loading Gear Marker
1
Inclined Base S Unit
Inclined Base T Unit
Loading Arm T Ass'y
Loading Arm S Ass'y
P4 Cap
Fig. 2-16-B 2-17: CLUTCH ASS'Y/RING SPRING/CLUTCH LEVER/ CLUTCH GEAR (Refer to Fig. 2-17-A) 1. 2. 3. 4. Remove the Polyslider Washer 1. Remove the Clutch Ass'y and Ring Spring. Remove the Clutch Lever. Remove the Coupling Gear, Coupling Spring and Clutch Gear.
1
Fig. 2-18-A NOTE 1. Do not touch the roller of Guide Roller. 2. In case of the P4 Cap installation, install it with parallel for "A" and "B" of Fig. 2-18-B. 3. In case of the Cassette Guide Post installation, install correctly as the circled section of Fig. 2-18-C.
"A" "B"
Clutch Ass'y
Ring Spring Coupling Gear Coupling Spring Clutch Gear
Clutch Lever
P4 Cap
Cassette Opener
Fig. 2-17-A NOTE 1. In case of the Clutch Ass'y installation, install it with inserting the spring of the Clutch Ass'y into the dent of the Coupling Gear. (Refer to Fig. 2-17-B) [OK]
Cassette Guide Post
Fig. 2-18-B
Clutch Ass'y
[NG]
Cassette Guide Post
Coupling Gear
Fig. 2-17-B B2-6
Fig. 2-18-C
DISASSEMBLY INSTRUCTIONS
3. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 3-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 3-3.)
Fig. 3-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 3-4.)
Screwdriver
CRT Support Alligator Clip
GND on the CRT
Fig. 3-1
Fig. 3-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 3-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 3-2.) Rubber Cap
CRT Support Fig. 3-2
CRT
Support Fig. 3-5
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
B3-1
DISASSEMBLY INSTRUCTIONS
4. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 4-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 4-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
Masking Tape (Cotton Tape)
IC
Tweezers
Fig. 4-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 4-2.) NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. 4. Peel off the Masking Tape.
Fig. 4-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 4-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Blower type IC desoldering machine
Braided Shield Wire
Soldering Iron
IC
Fig. 4-2
IC pattern
Fig. 4-4
B4-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 4-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 4-8.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 4-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 4-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 4-6.)
Solder
Soldering Iron
IC
Supply soldering from upper position to lower position
Fig. 4-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 4-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Braided Shield Wire
Fig. 4-7
B4-2
KEY TO ABBREVIATIONS
A A/C ACC AE AFC AFT AFT DET AGC AMP ANT A.PB APC ASS'Y AT AUTO A/V B BGP BOT BPF BRAKE SOL BUFF B/W C C CASE CAP CARR CH CLK CLOCK (SY-SE) COMB CONV CPM CTL CYL CYL-M CYL SENS D DATA (SY-CE) dB DC DD Unit DEMOD DET DEV E E EF EMPH ENC ENV EOT EQ EXT F F FBC FE FF FG FL SW FM FSC FWD G GEN GND H H.P.F : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Audio/Control Automatic Color Control Audio Erase Automatic Frequency Control Automatic Fine Tuning Automatic Fine Tuning Detect Automatic Gain Control Amplifier Antenna Audio Playback Automatic Phase Control Assembly All Time Automatic Audio/Video Burst Gate Pulse Beginning of Tape Bandpass Filter Brake Solenoid Buffer Black and White Capacitance, Collector Cassette Capstan Carrier Channel Clock Clock (Syscon to Servo) Combination, Comb Filter Converter Capstan Motor Control Cylinder Cylinder-Motor Cylinder-Sensor Data (Syscon to Servo) Decibel Direct Current Direct Drive Motor Unit Demodulator Detector Deviation Emitter Emitter Follower Emphasis Encoder Envelope End of Tape Equalizer External Fuse Feed Back Clamp Full Erase Fast Forward, Flipflop Frequency Generator Front Loading Switch Frequency Modulation Frequency Sub Carrier Forward Generator Ground High Pass Filter I H.SW Hz IC IF IND INV KIL L LED LIMIT AMP LM, LDM LP L.P.F LUMI. M MAX MINI MIX MM MOD MPX MS SW NC NR OSC OPE PB PB CTL PB-C PB-Y PCB P. CON PD PG P-P R REC REC-C REC-Y REEL BRK REEL S REF REG REW REV, RVS RF RMC RY S. CLK S. COM S. DATA SEG SEL SENS SER SI SIF SO SOL SP STB SW : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Head Switch Hertz Integrated Circuit Intermediate Frequency Indicator Inverter Killer Left Light Emitting Diode Limiter Amplifier Loading Motor Long Play Low Pass Filter Luminance Motor Maximum Minimum Mixer, mixing Monostable Multivibrator Modulator, Modulation Multiplexer, Multiplex Mecha State Switch Non Connection Noise Reduction Oscillator Operation Playback Playback Control Playback-Chrominance Playback-Luminance Printed Circuit Board Power Control Phase Detector Pulse Generator Peak-to Peak Right Recording Recording-Chrominance Recording-Luminance Reel Brake Reel Sensor Reference Regulated, Regulator Rewind Reverse Radio Frequency Remote Control Relay Serial Clock Sensor Common Serial Data Segment Select, Selector Sensor Search Mode Serial Input Sound Intermediate Frequency Serial Output Solenoid Standard Play Serial Strobe Switch
K L
M
N O P
R
S
C1-1
KEY TO ABBREVIATIONS
S SYNC SYNC SEP T TR TRAC TRICK PB TP U UNREG V V VCO VIF VP V.PB VR V.REC VSF VSR VSS V-SYNC VT X X'TAL Y Y/C : : : : : : : : : : : : : : : : : : : : : Synchronization Sync Separator, Separation Transistor Tracking Trick Playback Test Point Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display Video Playback Variable Resistor Video Recording Visual Search Fast Forward Visual Search Rewind Voltage Super Source Vertical-Synchronization Voltage Tuning Crystal Luminance/Chrominance
C1-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remocon key simultaneously. The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 5 seconds before Power On. Set Key VOL. (-) MIN Remocon Key 0 Releasing of V-CHIP PASSWORD. Initialization of the factory. NOTE: Do not use this for the normal servicing. Horizontal position adjustment of OSD. NOTE: Also can be adjusted by using the Adjustment MENU. Refer to the "ELECTRICAL ADJUSTMENT" (OSD HORIZONTAL). Adjust the PG SHIFTER automatically. Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER). Adjust the PG SHIFTER manually. Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER). Adjusting of the Tracking to the center position. NOTE: Also can be adjusted by pressing the ATR button for more than 2 seconds during PLAY. POWER ON total hours and PLAY/REC total hours are displayed on the screen. Refer to the "PREVENTIVE CHECKS AND SERVICE INTERVALS" (CONFIRMATION OF HOURS USED). Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". VOL. (-) MIN 8 Writing of EEPROM initial data. NOTE: Do not use this for the normal servicing. Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). Operations
VOL. (-) MIN
1
VOL. (-) MIN
2
VOL. (-) MIN
3
VOL. (-) MIN
4
VOL. (-) MIN
5
VOL. (-) MIN
6
VOL. (-) MIN
9
Method Press the ATR button on the remote control for more than 2 seconds during PLAY. Make the short circuit between the test point of SERVICE and the GND.
Operations Adjusting of the Tracking to the center position. Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL ADJUSTMENT" (PG SHIFTER). The EOT/BOT/Reel sensor do not work at this moment. Refer to the "PREPARATION FOR SERVICING"
C2-1
PREVENTIVE CHECKS AND SERVICE INTERVALS
The following standard table depends on environmental conditions and usage. Unless maintenance is properly carried out, the following service intervals may be quite shortened as harmful effects may be had on other parts. Also, long term storage or misuse may cause transformation and aging of rubber parts. Time Parts Name Audio Control Head Full Erase Head (Recorder only) Capstan Belt Pinch Roller Capstan DD Unit Loading Motor Tension Band Capstan Shaft Tape Running Guide Post Cylinder Unit : Clean : Replace Replace when rolling becomes abnormal. Clean the Head Clean those parts in contact with the tape.
Clean the rubber, and parts which the rubber touches.
500 hours
1,000 hours
1,500 hours
2,000 hours
3,000 hours
Notes
CONFIRMATION OF HOURS USED
POWER ON total hours and PLAY/REC total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: The confirmation of using hours will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 5 seconds before Power On. 1. Set the VOLUME to minimum. 2. While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously. 3. After the confirmation of using hours, turn off the power.
INIT
00
83
Initial setting content of MEMORY IC. POWER ON total hours. PLAY/REC total hours.
POWER ON 0010 PLAY/REC 0003
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
C3-1
PREVENTIVE CHECKS AND SERVICE INTERVALS
CLEANING
NOTE After cleaning the heads with isopropyl alcohol, do not run a tape until the heads dry completely. If the heads are not completely dry and alcohol gets on the tape, damage may occur. 1. AUDIO CONTROL HEAD Clean the Audio Control Head with the cotton stick soaked by alcohol. Clean the full erase head in the same manner. (Refer to the figure below.) 2. TAPE RUNNING SYSTEM When cleaning the tape transport system, use the gauze moistened with isopropyl alcohol. 3. CYLINDER Wrap a piece of chamois around your finger. Dip it in isopropyl alcohol. Hold it to the cylinder head softly. Turn the cylinder head counterclockwise to clean it (in the direction of the arrow). (Refer to the figure below.) NOTE Do not exert force against the cylinder head. Do not move the chamois upward or downward on the head. Use the chamois one by one.
Audio Control Head Cylinder Head
C3-2
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: Initial Data setting will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 5 seconds before Power On. INI 00 10 20 30 40 50 60 +0 88 B2 06 28 43 53 63 +1 0A 9A 29 29 44 54 64 +2 62 92 01 2A 45 55 66 +3 63 93 17 2C 46 56 69 +4 43 00 10 2E 47 57 6D +5 14 00 60 30 48 58 74 +6 34 00 32 32 49 59 79 +7 09 15 3A 34 4A 5A 7C +8 51 08 DA 36 4B 5B 7E +9 38 00 D7 38 4C 5C 7F +A 30 A9 10 3A 4D 5D --+B 66 0F 15 3C 4E 5E --+C 00 94 20 3E 4F 5F --+D 40 3E 25 40 50 60 --+E 00 06 26 41 51 61 --+F 10 04 27 42 52 62 ---
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously. ADDRESS and DATA should appear as FIG 1.
ADDRESS DATA
INIT
00
83
POWER ON 0010 PLAY/REC 0003
Fig. 1 3. ADDRESS is now selected and should "blink". Using the PLAY or STOP button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using PLAY or STOP until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. The unit will now have the correct DATA for the new MEMORY IC.
C4-1
SERVICING FIXTURES AND TOOLS
(For 2 heads model) VHS Alignment Tape JG001 (VN 2 S-LI6 3 ) JG001A (VN 2 S-CO13 ) JG001Q (VN 2 S-LI6 3 H) JG001T (VN 2 S-X6 3 ) (For 4 heads model) VHS Alignment Tape JG001B (VN 1 S-LI6 3 ) JG001I (VN 1 S-CO13 ) JG001P (VN 1 S-LI6 3 H) JG001S (VN 1 S-X6 3 )
JG002B Adapter JG002E Dial Torque Gauge (10~90gf·cm) JG002F (60~600gf·cm)
JG005 Post Adjustment Screwdriver Part No. SV-TG0-030-000 (small)
JG153 X Value Adjustment Screwdriver
JG022 Master Plane
JG024A Reel Disk Height Adjustment Jig
JG100A Torque Tape (VHT-063)
JG154 Cable
Tentelometer
Ref. No. JG001 JG001A JG001Q JG001T JG001B JG001I JG001P JG001S JG002B JG002E JG002F JG005 JG153 JG022 JG024A JG100A JG154
Part No. APJG001000 APJG001A00 APJG001Q00 APJG001T00 APJG001B00 APJG001I00 APJG001P00 APJG001S00 APJG002B00 APJG002E00 APJG002F00 APJG005000 APJG153000 APJG022000 APJG024A00 APJG100A00 APJG154000
Parts Name VHS Alignment Tape (For 2 heads model) VHS Alignment Tape (For 2 heads model) VHS Alignment Tape (For 2 heads model) VHS Alignment Tape (For 2 heads model) VHS Alignment Tape (For 4 heads model) VHS Alignment Tape (For 4 heads model) VHS Alignment Tape (For 4 heads model) VHS Alignment Tape (For 4 heads model) Adapter Dial Torque Gauge (10~90gf·cm) Dial Torque Gauge (60~600gf·cm) Post Adjustment Screwdriver X Value Adjustment Screwdriver Master Plane Reel Disk Height Adjustment Jig Torque Tape (VHT-063) Cable Monoscope, 6KHz Color Bar, 1KHz Hi-Fi Audio X Value Adjustment Monoscope, 6KHz Color Bar, 1KHz Hi-Fi Audio X Value Adjustment
Remarks
VSR Torque, Brake Torque (S Reel/T Reel Ass'y) Brake Torque (T Reel Ass'y) VSR Torque, Brake Torque (S Reel) Guide Roller Adjustment X Value Adjustment Reel Disk Height Adjustment Reel Disk Height Adjustment Playback Torque, Back Tension Torque During Playback Used to connect the test point of SERVICE and GROUND
PREPARATION FOR SERVICING
How to use the Servicing Fixture 1. Unplug the connector CP757 and CP353, then remove the TV/VCR Block from the set. 2. Remove the Operation PCB from the set, then connect it with the Syscon PCB. If necessary, connect CP353. (Front A/V Jack Input Terminal) 3. Short circuit between TP1001 and Ground with the cable JG154. (Refer to MAJOR COMPONENTS LOCATION GUIDE) 4. The EOT, BOT and Reel Sensor do not work at this moment. At that time, the STOP/EJECT button is available to insert and eject the Cassette Tape. C5-1
MECHANICAL ADJUSTMENTS
1. CONFIRMATION AND ADJUSTMENT
Read the following NOTES before starting work. · Place an object which weighs between 450g~500g on the Cassette Tape to keep it steady when you want to make the tape run without the Cassette Holder. (Do not place an object which weighs over 500g.) · When you activate the deck without the Cassette Holder, short circuit between TP1001 and GND. (Refer to ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE) In this condition the BOT/EOT/Reel Sensor will not function. 1-1: CONFIRMATION AND ADJUSTMENT OF REEL DISK HEIGHT 1. Turn on the power and set to the STOP mode. 2. Set the master plane (JG022) and reel disk height adjustment jig (JG024A) on the mechanism framework, taking care not to scratch the drum, as shown in Fig. 11-A. 3. While turning the reel and confirm the following points. Check if the surface "A" of reel disk is lower than the surface "B" of reel disk height adjustment jig (JG024A) and is higher than the surface "C". If it is not passed, place the height adjustment washers and adjust to 10(+2, -0)mm. 4. Adjust the other reel in the same way.
Master Plane (JG022)
1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 1. Set to the PLAY mode. 2. Adjust the adjusting parts for the Tension Arm position so that the Tension Arm top is within the standard line of Main Chassis. 3. While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above.
Standard line of Main Chassis
Tension Arm
0.5mm (Adjusting range)
Fig. 1-2-A
Adjusting parts for the Tension Arm position
Tension Band
Reel Disk Height Adjustment Jig (JG024A)
The Tension Arm top will move to the inside direction of the Main Chassis. Bend
The Tension Arm top will move to the outside direction of the Main Chassis.
Fig. 1-2-B
1-3: CONFIRMATION OF PLAYBACK TORQUE AND BACK TENSION TORQUE DURING PLAYBACK 1. Load a video tape (T-120) recorded in standard speed mode. Set the unit to the PLAY mode. 2. Install the tentelometer as shown in Fig. 1-3. Confirm that the meter indicates 20 ± 2gf in the beginning of playback. Fig. 1-1-A
Reel Disk Height Adjustment Jig (JG024A)
· USING A CASSETTE TYPE TORQUE TAPE (JG100A) 1. After confirmation and adjustment of Tension Post position (Refer to item 1-2), load the cassette type torque tape (JG100A) and set to the PLAY mode. 2. Confirm that the right meter of the torque tape indicates 50~90gf·cm during playback in SP mode. 3. Confirm that the left meter of the torque tape indicates 25~40gf·cm during playback in SP mode.
Tentelometer
Reel Disk
Master Plane (JG022)
(B)
10(+0.2, -0)mm (C)
Video Tape (A) Height Adjustment Washer 2.6x4.7xT0.13 2.6X4.7xT0.25
Fig. 1-1-B
P1 Post
Guide Roller
Fig. 1-3
D1-1
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE 1. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Picture Search (Rewind) mode. (Refer to Fig.1-4-B) 2. Then, confirm that it indicates 120~180gf·cm. NOTE Install the Torque Gauge on the reel disk firmly. Press the REW button to turn the reel disk. 1-5: CONFIRMATION OF REEL BRAKE TORQUE (S Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Ass'y from the S Reel. 3. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Turn the Torque Gauge (JG002F) clockwise. 4. Then, confirm that it indicates 60~100gf·cm. (T Reel Brake) (Refer to Fig. 1-4-B) 1. Once set to the Fast Forward mode then set to the Stop mode. While, unplug the AC cord when the Pinch Roller Block is on the position of Fig. 1-4-A. 2. Move the Idler Ass'y from the T Reel. 3. Install the Torque Gauge (JG002E) and Adapter (JG002B) on the T reel. Turn the Torque Gauge (JG002E) counterclockwise. 4. Then, confirm that it indicates 30~50gf·cm.
The position at FF mode. Pinch Roller Block Stop at this position.
NOTE If the torque is out of the range, replace the following parts. Check item 1-4 1-5 Replacement Part Idler Ass'y/Clutch Ass'y S Reel side: S Reel/Tension Band/Tension Connect/Tension Arm Ass'y T Reel side: T Reel/T Brake Band//T Brake Spring/T Brake Arm
2. CONFIRMATION AND ADJUSTMENT OF TAPE RUNNING MECHANISM
Tape Running Mechanism is adjusted precisely at the factory. Adjustment is not necessary as usual. When you replace the parts of the tape running mechanism because of long term usage or failure, the confirmation and adjustment are necessary. 2-1: GUIDE ROLLER 1. Playback the VHS Alignment Tape (JG001 or JG001B). (Refer to SERVICING FIXTURE AND TOOLS) 2. Connect CH-1 of the oscilloscope to TP4001 (Envelope) and CH-2 to TP1002 (SW Pulse). 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Trigger with SW Pulse and observe the envelope. (Refer to Fig. 2-1-A) 5. When observing the envelope, adjust the Adjusting Driver (JG005) slightly until the envelope will be flat. Even if you press the Tracking Button, adjust so that flatness is not moved so much. 6. Adjust so that the A : B ratio is better than 3 : 2 as shown in Fig. 2-1-B, even if you press the Tracking Button to move the envelope (The envelope waveform will begin to decrease when you press the Tracking Button). 7. Adjust the PG shifter during playback. (Refer to the ELECTRICAL ADJUSTMENTS) NOTE
The position at STOP mode. Capstan DD Unit
Cassette Opener
Cassette Holder Ass'y
Fig. 1-4-A
Torque Gauge/Adapter (JG002F/JG002B)
After adjustment, confirm and adjust A/C head. (Refer to item 2-2)
CH-1 Envelope (TP4001)
Torque Gauge/Adapter (JG002E/JG002B) CH-2 SW Pulse (TP1002)
CH-1 Track
CH-2 Track
Fig. 2-1-A
Entrance S Reel Max Max Exit
A
B
T Reel
Fig. 1-4-B
A:B3:2
Fig. 2-1-B
D1-2
MECHANICAL ADJUSTMENTS
2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ CONTROL HEAD When the Tape Running Mechanism does not work well, adjust the following items. 1. Playback the VHS Alignment Tape (JG001 or JG001B) . (Refer to SERVICING FIXTURE AND TOOLS) 2. Confirm that the reflected picture of stamp mark is appeared on the tape prior to P4 Post as shown in Fig. 2-2-A. a) When the reflected picture is distorted, turn the screw 1 clockwise until the distortion is disappeared. b) When the reflected picture is not distorted, turn the screw 1 counterclockwise until little distortion is appeared, then adjust the a). 3. Turn the screw 2 to set the audio level to maximum. 4. Confirm that the bottom of the Audio/ Control Head and the bottom of the tape is shown in Fig. 2-2-C. c) When the height is not correct, turn the screw 3 to adjust the height. Then, adjust the 1~3 again.
Audio/Control Head Reflected picture of Stamp Mark P4 Post (1) CH-3 Audio (2) Envelope
2-3: TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) 1. Confirm and adjust the height of the Reel Disk. (Refer to item 1-1) 2. Confirm and adjust the position of the Tension Post. (Refer to item 1-2) 3. Adjust the Guide Roller. (Refer to item 2-1) 4. Confirm and adjust the Audio/Control Head. (Refer to item 2-2) 5. Connect CH-1 of the oscilloscope to TP4001, CH-2 to TP1002 and CH-3 to HOT side of Audio Out Jack. 6. Playback the VHS Alignment Tape (JG001S or JG001T). (Refer to SERVICING FIXTURE AND TOOLS) 7. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 8. Set the X Value adjustment driver (JG153) to the 4 of Fig. 2-2-B. Adjust X value so that the envelope waveform output becomes maximum. Check if the relation between Audio and Envelope waveform becomes (1) or (2) of Fig. 2-3.
Fig. 2-3
Stamp Mark
Fig. 2-2-A
2-4: CONFIRM HI-FI AUDIO (Hi-Fi model only) 1. Connect CH-1 of the oscilloscope to TP1002 and CH-2 to the Hi-Fi Audio Out Jack. 2. Playback the VHS Alignment Tape (JG001P or JG001Q). (Refer to SERVICING FIXTURE AND TOOLS) 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Press the Tracking Up button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 5. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 6. Press the Tracking Down button and count number of steps which the audio output is changed from Hi-Fi (10KHz) to MONO (6KHz). 7. If the difference are more than 3 steps, set the X Value adjustment driver (JG153) to 4 of Fig. 2-2-B. Change the X Value and adjust it so that the value becomes within 2 steps.
Audio/Control Head
3
1
2 4
Fig. 2-2-B
Audio/Control Head Tape
0.25±0.05mm
Fig. 2-2-C
D1-3
MECHANICAL ADJUSTMENTS
3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
4 5
6 3
2
7
1
10
9
8
1. Tension Connect 2. Tension Arm 3. Guide Roller 4. Audio/Control Head 5. X value adjustment driver hole
6. 7. 8. 9. 10.
P4 Post T Brake Spring T Reel S Reel Adjusting parts for the Tension Arm position
D1-4
ELECTRICAL ADJUSTMENTS
1. BEFORE MAKING ELECTRICAL ADJUSTMENTS
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION · Use an isolation transformer when performing any service on this chassis. · Before removing the anode cap, discharge electricity because it contains high voltage. · When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. Inferior silicon grease can damage IC's and transistors. · When replacing IC's and transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon. On-Screen Display Adjustment 1. Unplug the AC plug for more than 5 seconds to set the clock to the non-setting state. Then, set the volume level to minimum. 2. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control simultaneously to appear the adjustment mode on the screen as shown in Fig. 1-1.
2. BASIC ADJUSTMENTS (VCR SECTION)
2-1: PG SHIFTER 1. Connect CH-1 on the oscilloscope to TP1002 and CH-2 to pin 4 of CP1003. 2. Playback the alignment tape. (JG001A) 3. Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center. 4. Press the VOL. DOWN button on the set and the channel button (3) on the remote control simultaneously until the indicator REC disappears. If the indicator REC disappears, adjustment is completed. (If the above adjustments doesn't work well:) 5. Press the VOL. DOWN button on the set and the channel button (3) on the remote control simultaneously until the indicator REC disappears. 6. When the REC indicator is blinking, press both VOL. DOWN button on the set and the channel button (4) on the remote control simultaneously and adjust the Tracking +/- button until the arising to the down of Head Switching Pulse becomes 6.5 ± 0.5H. (Refer to Fig. 2-1-A, B) 7. Press the Tracking Auto button.
CH-2
TV
6.5H CH-1
00 OSD
15 Fig. 1-1
Fig. 2-1-A
3. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 4. Press the MENU button on the remote control to end the adjustments.
6.5H
CH-2
CH-1
NO. 00 01 02 03 04 05 06 07 08 09 10 11 12
FUNCTION OSD H CUT OFF RF AGC DELAY VIF VCO H VCO H PHASE V SIZE V SHIFT R DRIVE B DRIVE R CUT OFF G CUT OFF B CUT OFF
NO. 13 14 15 16 17 18 19 20 21 22 23 24
FUNCTION BRIGHTNESS CONTRAST COLOR TINT SHARPNESS FM LEVEL LEVEL SEPARATION 1 SEPARATION 2 TEST MONO TEST STEREO X-RAY TEST Fig. 1-2
Fig. 2-1-B 2-2: VCO FREERUN 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the VHF HIGH. 3. Disconnect the Antenna while receiving the VHF HIGH and set to the Noise screen. 4. Once turn off the Power and turn on the Power again. 5. Approxi. 3 seconds later, input the Antenna again. 6. Connect the digital voltmeter between the pin 5 of CP351 and the pin 1 (GND) of CP351. 7. Activate the adjustment mode display of Fig. 1-1 and press the channel button (03) on the remote control to select "VIF VCO". 8. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.5V. 9. After the 2.5V adjustment, countdown the VIF VCO step No. by 1 step with the VOL. DOWN button.
D2-1
ELECTRICAL ADJUSTMENTS
2-3: RF AGC DELAY 1. Receive the VHF HIGH (63dB). 2. Connect the digital voltmeter between the pin 5 of CP351 and the pin 1 (GND) of CP351. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (02) on the remote control to select "RF AGC DELAY". 4. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.9V ± 0.15V. 2-8: HORIZONTAL PHASE 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (05) on the remote control to select "H PHASE". 4. Press the VOL. UP/DOWN button on the remote control until the right and left screen size of the vertical line becomes the same. 2-9: VERTICAL SHIFT 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V SHIFT". 4. Press the VOL. UP/DOWN button on the remote control until the horizontal line becomes fit to the notch of the shadow mask. 2-10: VERTICAL SIZE 1. Receive the cross hatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V SIZE". 4. Press the VOL. UP/DOWN button on the remote control until the rectangle on the center of the screen becomes square. 5. Receive a broadcast and check if the picture is normal. 2-11: SUB BRIGHTNESS 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select "BRIGHTNESS". 4. Press the VOL. UP/DOWN button on the remote control until the white 10% is starting to be visible 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 2-11: SUB CONTRAST MANUAL 2-7: FOCUS 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Turn the Focus Volume fully counterclockwise once. 4. Adjust the Focus Volume until picture is distinct. 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (14) on the remote control to select "CONTRAST". 4. Press the VOL. UP/DOWN button on the remote control until the contrast STEP No. becomes "100". Receive the color bar pattern. (Audio Video Input) 5. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. D2-2
(TV SECTION)
2-4: CONSTANT VOLTAGE 1. Connect the digital voltmeter to the TP601. 2. Set condition is AV MODE without signal. 3. Using the remote control, set the brightness and contrast to normal position. 4. Adjust the VR502 until the digital voltmeter is 135 ± 0.5V. 2-5: CUT OFF 1. Adjust the unit to the following settings. R CUT OFF=128, G CUT OFF=128, B CUT OFF=128, BRIGHTNESS=128, CONTRAST=100 2. Place the set with Aging Test for more than 15 minutes. 3. Set condition is AV MODE without signal. 4. Using the remote control, set the brightness and contrast to normal position. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 6. Adjust the Screen Volume until a dim raster is obtained. 2-6: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the color bar pattern. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (10) on the remote control to select "R CUT OFF". 5. Using the VOL. UP/DOWN button on the remote control, adjust the R CUT OFF. 6. Press the CH. UP/DOWN button on the remote control to select the "R DRIVE", "B DRIVE", "G CUT OFF" or "B CUT OFF". 7. Using the VOL. UP/DOWN button on the remote control, adjust the R DRIVE, B DRIVE, G CUT OFF or B CUT OFF. 8. Perform the above adjustments 6 and 7 until the white color is looked like a white.
ELECTRICAL ADJUSTMENTS
2-13: SUB TINT 1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to TP801. 3. Using the remote control, set the brightness, contrast, color and tint to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "TINT". 5. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes a straight line. (Refer to Fig. 2-2) 6. Receive the color bar pattern. (Audio Video Input) 7. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. 2-15: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-4)
TV
00 OSD A 2-16: SUB SHARPNESS
15 B
Fig. 2-4
"A"
1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "SHARPNESS". 2. Check if the step No. of SHARPNESS is "40". 3. Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 1, 2. Fig. 2-2 2-17: H VCO
2-14: SUB COLOR 1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to TP803. 3. Using the remote control, set the brightness, contrast, color and tint to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (15) on the remote control to select "COLOR". 5. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 6. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 110% of the white level. (Refer to Fig. 2-3) 7. Receive the color bar pattern. (Audio Video Input) 8. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~6. White 0%
1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (04) on the remote control to select "H VCO". 2. Check if the step No. of H VCO is "4".
100%
Red Level White 100%
Fig. 2-3
D2-3
ELECTRICAL ADJUSTMENTS
3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE
CP1003
TP1001
TP4001 TP1002
TP601 VR502
TU601
FB401 CP351
FOCUS VOLUME SCREEN VOLUME
SYSCON PCB
TP801 J801 TP803
CRT PCB
D2-4
ELECTRICAL ADJUSTMENTS
4. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 4-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 4-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 4-2: PURITY NOTE Adjust after performing adjustments in section 4-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue colors. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 4-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 4-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 4-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 4-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 4-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 4-2-b) RGB RGB
R G B
R G B RIGHT/LEFT SLANT
UPWARD/DOWNWARD SLANT
Fig. 4-2-a
WEDGE
WEDGE
WEDGE WEDGE POSITION Fig. 4-2-b
6 POLE MAGNETS 4 POLE MAGNETS PURITY MAGNETS Fig. 4-1
D2-5
TV BLOCK DIAGRAM
MICON/ OPERATION/ DECK
V. OUTPUT IC IC401 AN5522 SCL SDA Q602, Q603 REG. Q601 BUFFER CHROMA IC IC601 M61206FP 63 48 IF AGC FILTER IF AGC NC 42 MCU RESET Q606 REG. Q604, Q605 REG. AT+5V 1 AT+12V AMP PUMP UP 5 7 Q405 33 39 46 SW REG CONT 8.7V REG OUT 5V REG 13 POWER ON CONT 53 FM DIRECT OUT 50 FB401 10 5 27 14 15 16 1 COL 2 +B 6 E180 7 ABL 9 AFC 10 HEA E180V V OUT 31 ACL/ABCL V PLUSE OUT V RAMP FEED BACK CHROMA APC FILTER 17 29 21 F S 3 HV J801 F 8 3 7 9 V801 CRT H-DRIVE Q406 H. OUTPUT DY AUDIO OUT SDA SCL FAST BLK R OUT G OUT B OUT THERMAL PROTECTION
AT+5V_BACK UP AT+12V
Y/C/AUDIO/ CCD/ HEAD AMP/ IN/OUT
TU_AUDIO TU_VIDEO Y/C_AUDIO
VCC 2 3
Q407 H-CONTROL SW
H_CTL
MICON/ OPERATION/ DECK
52 EXT AUDIO IN
56 57 VIF APC FILTER VIF VIDEO OUT
55 VREG VCC
41 5.7V REG OUT (FOR CPU)
TU601 1 4 5 11 SAW FILTER CF601 1 4 5
62 1 64 60
RF AGC OUT VIF IN VIF IN AFT OUT
Q804
BLUE AMP Q608
Q806
RED AMP H. PLUSE OUT Q805 GREEN AMP FBP IN H OUT
CUT OFF SW
P. CON+8V
Q404 X-RAY MICON/ OPERATION/ DECK X-RAY_TEST Q403 SW. SW.
35
32
X' TAL
12
6
7
Q609 POWER ON SW.
TV_POWER-H VD HD OSD_BLK OSD_B OSD_R MICON/ OPERATION/ DECK
X602 3.579545MHz
L503 DEGAUSS COIL
TH501 2 2 1 1 POWER_FAIL F501 D501 RECTIFIER Q511 Q507 FEED BACK SW. +B ADJ VR502 FEED BACK Q501 TLP621(GR) Q510 SWITCHING
5
OSD_G Q611 POWER FAIL SW. AFT_M SOUND AMP IC IC351 AN7511 2 T501 8 SWITCHING
11 13
6 8
J351 HEAD JACK CD352 SP+ SP SP351 SPEAKER
AC IN
5 AT+12V UNREG+8V POWER_FAIL 1 4
14
16 3
F502
5V REG IC 501 KIA7805P1
P. CON+5V VCR_POWER-H TV_POWER-H TV_A_MUTE MICON/ OPERATION/ DECK
E-1
E-2
Y/C/AUDIO/CCD/HEAD AMP/IN/OUT BLOCK DIAGRAM
X4001 3.579545MHz
Q4012 Y/C/AUDIO/CCD/HEAD AMP IC IC4001 LA71200M-MPB 50 49 BUFFER
Q4010 BUFFER
41
43
38 VSS
37
VX01 NC 67 P L H
PLL REC APC 3.58M BPF2 R Main CONV P CLAMP CCD B-UP AMP AGC AUTO-BIAS 53 Y/C_CLK Y/C_DATA Y/C_CS REC APC
NC 66 62 HA GND CP4001 1 CYL 2 SP-CH2 (L) 3 SP_COM 4 SP-CH1 (R) 73 74 65 72
R
P P H L C-LPF
SERAIL DECODER
54 55
MICON/ OPERATION/ DECK
R P
UOT VCA 36 ACC DET 3.58M BPF1 39 SYNC C-ROT SEP RF-SW IN 57