Text preview for : HR5001C-TE.pdf part of MAKITA HR5001C-TE MAKITA HR5001C-TE.pdf
Back to : HR5001C-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. HR5001C
New Tool
118 (4-5/8")
Description 50mm Rotary Hammer
CONCEPTION AND MAIN APPLICATIONS
Model HR5001C is 50 mm rotary hammer for the SSDS-max bit
(11")
280
designed as the sister version the existing Model HR4000C.
Its brief benefits are;
*Can achive the highest efficiency in this class.
*Electrical speed control feature
Variable speed
Soft start
Steady speed 610
(24")
Specifications
Voltage(V) Current(A) Cycle(Hz) Continuous Rating(W) Max.Output(W)
Input Output
100 15 50/60 1450 460 1400
110 15 50/60 1500 600 1900
120 15 50/60 1500 600 1900
220 7.7 50/60 1500 600 1900
230 7.4 50/60 1500 600 1900
240 7.1 50/60 1500 600 1900
No load speed Rotations per minute 120 ~ 240rpm
Blows per minute 1100 ~ 2150bpm
Bit type SDS-max. shank
Diameter of shank : 18 mm(11/16'')
Max.capacities (Work : Concrete) T.C.T.Bit:50mm(2")
Core bit : 160 mm(6-5/16")
Net weight 10Kg(22bs)
Cord length 5m(16.4ft)
Standard equipment
Grease Vessel ------------------1 pc.
Plastic Carrying Case --------1 pc.
Bar-type handle ---------------1 pc.
D-type handle -----------------1 pc.
Optional accessories
T.C.T.Bit : 19(3/4"), 20(15/16"), 21.5(7/8"), 22(7/8"), 25(1"), 28(1-1/8"), 32(1-3/8"), 35(1-3/8"), 38(1-1/2")
Bull point 280, 400 Cold chisel 25~280,25~400 Scaling chisel 50 Tile chisel 50
Clay Spade Core bit adapteer D-type side handle
Core bit : 20(15/16"), 30(1-3/16"), 35(1-3/8"), 40(1-9/16"), 45(1-3/4"), 54(2-1/8"), 65(2-9/16"),
79(1-1/8"), 105(4-1/8") , 118(4-5/8")
Grease Vessel(Bit grease,Hammer grease) Depth Gauge Safety Goggle
Features and benefits
1. Double insulated
2. See the sheets attached for more information
HR5001C *:#Same features as HR4000C
Efficiency
The highest efficiency in this class.
All enclosure is made of resin. *
Even if the bit touches the electric wire
inside the wall,an electrical shock may
hardly hit on the operator.
Push-to-strike system
Bit does not jump arround.
Efficiency and endurance New torque limitter system
are improved. Roller clutch system
* Large change lever (#HR4000C:Ball clutch system)
Easy to change opeation mode
for coping with the higher power,
between "Hammering only"
and for improvement of endurance.
and "Rotation with hammerig"
* For pointing job, you can use
this toolholding barrel * Large trigger
No fatigue at finger after
without feeling heat from barrel long operation.
by resin cover
* One touch chuck
By just inserting,
the bit can be installed.
Lamp will light off,when *
switch or power supply
cord becomes defective.
* D-type handle ( Standard accessory) Lit during no defective.
Bar-handle ( Standard accessorry)
Lamp will light up for *
Both handles can be fixed at any angle and
indicating time for
at any positions back/forth on the barrel. replacement of
The D-type handle for hammering can be carbon brushes
swiveled at 8 positions back/forth. It will light up about 8-hr
Automatic cut-off before the carbon brush are
carbon brush worn out.
Carbon brushes can be Power supply cord or *
replaced without switch can be easily
replaced.
remove the rear cover.
by removing two screws
of handle cover.
270mm 200mm
Holding power required when torque limiter operating
Approx. 20 kgf Approx. 29 kgf Speed adjustable dial
Makita #HR5001C Bosch #GBH10DC Light hammering or drilling
Longer life motor is easily performed
* Large model plastic case
(standard accessory) The thicness of the commutator is by setting lower speed.
600 mm(23-5/8") bit. can be 2 times of HR5000 .
carried. The varnish is coated on the armature
against dust.
Repair
(1) Removing Change lever ------------------------------ ------(Page 6 of 14)
(2) Install Change lever ------------------------------- ----------(Page 6 of 14)
(3) Replace the Armature ------------------------------- --------(Page 7 of 14)
(4) Disassembling the chuck --------------------------- -------(Page 8 of 14)
(5) Assembling the chuck ------------------------------- -------(Page 8 of 14)
(6) Removing Tool holderers --------------------------- ------(Page 8 of 14)
(7) Disassembling tool holders ------------------------- -------(Page 9 of 14)
(8) Assembling the tool holder A and B ----------------- -----(Page 9 of 14)
(9) Taking out Cylinder 40 ----------------------------- --------(Page 9 of 14)
(10) Assembling Piston, Rod and Crank shaft -------------- -(Page 10 of 14)
(11) Assembling Fluoride ring 28 on Impact bolt ---------- (Page 10 of 14)
(12) Assembling several parts in Crank housing ----------- (Page 11 of 14)
(13) Inserting T ool holders -------------------------------------(Page 11 of 14)
(14) Assembling Torque limiter complete -------------------(Page 12 of 14)
(15) Lublication ----------------------------------------- --------(Page 13 of 14)