Text preview for : ACR-224MMU.pdf part of Akai ACR-224MMU Akai ACR ACR-224MMU ACR-224MMU.pdf
Back to : ACR-224MMU.pdf | Home
Downloaded from www.Manualslib.com manuals search engine
DISASSEMBLY INSTRUCTIONS
1. Using the unlock key that came with the unit or a similar tool, unlock the Mounting Box and remove toward
the rear of the unit.
2. Remove two screws (A) located on the rear of the top cabinet then remove the Top Cabinet.
3. Remove two screws (B) located on the rear of the bottom cabinet then remove the Bottom Cabinet.
4. Take out the Front Panel and the Ring.
Remove the screws(C) from on the front side of the Base.
5. Remove two screws (D) from on the right side of the Rear-right Cabinet.
Remove the screw (E) from on the left side of the Rear-right Cabinet and the screw (F) on the right side of
the heat sink.
6. Remove two screws (G) from on the back of the Rear-right bracket then remove the ISO Antenna
Socket/Short W/Holder.
7. Remove two screws (H) from under the deck front bracket then remove the Deck Front Bracket.
Remove two screws (I) from under the deck rear bracket then remove the Deck Rear Bracket and the Deck.
8. Remove two screws (J) from on the left side of the heat sink.
9. Remove two screws (K) from on the left side of the heat sink then remove the IC Bracket.
10. Remove two screws (L) from on the rear side of Rear-right Cabinet then remove the Power IC Bracket.
11. Remove two screws (M) from each side of the base then remove the Base.
12. Remove the screw (N) from right side of the Rear-right bracket then remove the Hexagon Nut..
13. Remove the screw (O) from on the back of the Rear-right then remove ISO 36PIN Socket.
14. Remove three screws (P) from under the main board then remove the Heat Sink, Rear-right Bracket and the
Main Board.
Downloaded from www.Manualslib.com manuals search engine
DISASSEMBLY DIAGRAM
Downloaded from www.Manualslib.com manuals search engine
OPERATION CHECK
GENERAL SPECIFICATIONS OF SIGNAL
Standard frequency FM 98.1 MHz (65.0, 74.0MHz) (87.5, 108.0 MHz)
MW 1000 kHz (522, 1620 kHz)
Signal output FM 1mV
MW 5 mV
Modulation MW 400 Hz 30% MOD.
FM Stereo 1 kHz 75kHz DEV.
46% for L only or
R only pilot level 8%
AF output level FM/MW
Power source voltage DC 14.0V (Backup voltage is the same as this)
AF load impedance 4 ohm pure resistance
Balance Center position of level
Tone Center position
The signal strength read in this section is voltage on the antenna.
Test Diagram
ACC (DV14.4V)
2-SPEAKER 4-SPEAKER 4-SPEAKER 2-SPEAKER
RR.
RL. SPK.
SPR. BACK UP (14.4V)
FRONT FRONT
SPK. SPK.
FL. FR.
SPK. SPE. GROUND
POWER ANTANNA
MAIN UNIT
ANT
MPX
DUMMY STEREOS
DISTORTION ANTANNA MODULATOR
METER VTVM VTVM
AM SG FM SG
Downloaded from www.Manualslib.com manuals search engine
BLOCK DIAGRAM
Downloaded from www.Manualslib.com manuals search engine
ALIGNMENT LOCATIONS
MITSUMI BOARD
Downloaded from www.Manualslib.com manuals search engine
ALIGNMENT PROCEDURES
FM ADJUSTMENT
Equipment Required
AM IF/RF signal generator
Solid-state voltmeter (SSVM)
Regulated DC power supply
2-CH voltmeter
Distortion meter
FM Alignment Using FM Signal Generator
Note: Press the radio power switch to on the radio. Signal generator output must be kept as low as possible
to avoid overload and clipping.
Step Generator Generator Display Adjustment Remarks
Coupling Setting
Stereo Signal 98.1 MHz Adjust AF
Separation Generator Int. 1 kHz 98.1 MHz VR1 output power
to antenna Dev. 75 kHz at maximum
receptacle L+R = 90 % separating
Pilot = 10 % more than 30 dB
FM SNC 98.1 MHz
Adjustment Dev. 75 kHz 98.1 MHz 98.1 MHz VR2 Stereo Separation
L+R=90 % @ 40 dB 25 dB (