Text preview for : MDV-30 Service Manual.pdf part of MYSTERY MDV-30 Service Manual . Rare and Ancient Equipment MYSTERY Car Audio Mystery MDV-30 MDV-30 Service Manual.pdf
Back to : MDV-30 Service Manual.pdf | Home
MYSTERY
MDV-30
Appearance 06
Specification 07
Harness Connection Diagram 08
Circuit Diagram 09
Circuit Operating 14
Block Diagram 16
Troubleshooting Guide 17
PCB Pattern 21
Assembly/Disassembly Drawing 24
Part List 25
APPEARANCE
FRONT
APPEARANCE
Power indicatior DVD disc holder
Power Eject
Earphone I.R Play/ Stop Skip A/V In
output jack Pause
REAR
Remote eye A/V Out Coaxial Power jack
in jack
6
SPECFICATION
INTRODUCTION
S P E C I F I C AT I O N
This DVD Player supports more 500 lines horizontal resolution, Dolby digital (AC-3) and outputs
digital DTS so that it provides the video and sound quality of the effect like a real theater. It can
also supports not only VIDEO CD but also CD, CD-R, CD-RW.
FEATURES
500 and more horizontal resolution
DVD, VCD, CD, CD-R, CD-RW
Dolby Digital Decoding
2CH Analogue signal output
DTS digital output
ZOOM
Special Play (Slow/Fast Play)
Composite output
SPECIFICATIONS
Basic Horizontal Resolution More than 500 lines
Specification Compatible Disc DVD, VCD, CD, CD-R, CD-RW
Dolby Digital Analogue 2Ch output & Digital output
Audio
DTS Digital output
ZOOM OK
Volume control OK
Convenience
Special play OK
MP3 Play OK
Video 1 Composite terminal
Output
Audio 2 2Ch RCA terminal (R/L, each) / 1 Coaxial terminal
Connection
Video 1 Composite terminal
Input
Audio 2 2Ch RCA terminal (R/L, 2 each)
Size 180 x 214 x 50 (W x D x H)
Weight About 1.5 Kg
7
HARNESS CONNECTION DIAGRAM
S P E C I F I C AT I O N
8
CIRCUIT DIAGRAM
FRONT
CIRCUIT DIAGRAM
9
MPEG
CIRCUIT DIAGRAM
10
CIRCUIT DIAGRAM
11
RF AMP
OUTPUT CONN
CIRCUIT DIAGRAM
12
CIRCUIT DIAGRAM
13
AUDIO
CIRCUIT OPERATING
C I R C U I T O P E R AT I N G
FRONT
VFD DRIVER : IC401 (V6313)
1. INTRODUCTION
With following functions, IC401 realizes the serial communication with MPEG (ES6629)
according to software.
CMOS Technology
Key Scanning (12 x 2 matrix)
8-step Dimming Circuit
Multi Display mode (10digit 16segment)
LED port supportable (5Ch, max 20mA)
I2C EPROM interface
POWER SW 1Port
2. INPUT/OUTPUT TERMINAL
INPUT : Receive VSTB, VCLK and VDAT from MPEG (ES6629) and scan key input at
voltage level.
OUTPUT : Output VDAT to MPEG (ES6629) and operate VFD.
With key value stored at EPROM by direct I2C communication, power control by
remote control signal is possible.
DESCRIPTION OF FRONT OPERATION
1. KEY SCAN & VFD DRIVER (V6313) INTERFACE
2. DESCRIPTION OF OPERATION
If a user presses a key while MPEG chip (ES6629) is scanning a key thru VFD Driver IC (V6313),
V6313 receives key input and if it inputs serially the received data to MPEG chip (ES6629), it
analyzes and proceed the command.
Operate the action according to an input command.
After EPROM reads and compares the remote control code received from IR remote control
sensor, power is controlled using PSW in case of KEY code.
14
C I R C U I T O P E R AT I N G
AUDIO
2CH AUDIO
1. INTRODUCTION
Receive FR and FL signals from MPEG Chip (ES6629), amplify (IC804) them to output
analogue signals to 2CH Jack (JK802).
Receive the output digital signal from MPEG Chip (ES6629) and output digital signal by
coaxial Jack.
OP-AMP : IC804 (LM4558)
1. INTRODUCTION
Dual Operating Amplifier
2. FUNCTIONS
Amplify the analogue voice signal from D/A converter IC.
Taking right/left channels each, amplify and output these two channels to AV OUTPUT.
3. INTERNAL BLOCK DIAGRAM
IC804
LM4558
4. TRUTH TABLE
INH A B C ON SWITCH
L L L L X0 YD Z0
L H L L X1 YD Z0
L L H L X0 YD Z0
L H H L X1 Y1 Z0
L L L H X0 YD Z1
L H L H X1 YD Z1
L L H H XD Y 1 Z 1
L H H H X1 Y 1 Z 1
L X X X NONE
15
BLOCK DIAGRAM
BLOCK DIAGRAM
16
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
POWER CIRCUIT
Power error
No
Impress power? Must impress power. Impress power.
Yes
No IC902 KA7805 is not 1. +12V must be running for the voltage of No.1
+5V power is running? working. pin and No.2 pin in IC902.
2. +5V must be running for the voltage of No.3
pin and No.2 pin in IC902.
3. Check the surrounding circuit of IC902 KA7805.
Yes 4. If 1. is working and 2. is not working, replace
IC.
No IC903 KA7809 is not 1. +12V must be running for the voltage of No.1
+9V power is running?
working. pin and No.2 pin in IC903.
2. +9V must be running for the voltage of No.3
pin and No.2 pin in IC903.
3. Check the surrounding circuit of IC903 KA7809.
Yes 4. If 1. is working and 2. is not working, replace
IC.
No Q3, QQ4 ASM1117 is 1. +5V must be running for the voltage of No.3
+3.3V power is running?
not working. pin and No.1 pin in Q3, QQ4.
2. +3.3V must be running for the voltage of No.2
pin and No.4 pin in Q3, QQ4.
3. Check the surrounding circuit of IC903 KA7809.
Yes 4. If 1. is working and 2. is not working, replace
IC.
No Q4, ASM1117 is not 1. +3.3V must be running for the voltage of No.3
+2V power is running? working. pin and No.1 pin in Q4.
2. +2V must be running for the voltage of No.2, 4
pin and No.1 pin in Q4.
3. Check the surrounding circuit of Q4 ASM1117.
4. If 1. is working and 2. is not working, replace
Yes IC.
OK
17
FRONT CIRCUIT
TROUBLESHOOTING GUIDE
Front key operation defect
Properly update No Other software is not P80 SOFTWEAR UPDATE.
the loader software? working as the key (If the power can not be on with power button
port is different. after other firmware update, impress +5V to PSW
by compulsion and power on.)
Yes
+5V is impressed No
to No.10 and 40 pin of As IC401 controls the 1. +5V must be running for No.42 pin of IC401.
IC401(V6313)? overall functions of (In case of SET OFF status)
FRONT, power should 2. Should check the cold soldering of No.10 and
be impressed. 40 pin in IC401.
Yes
All key is working?
No The pulse of IC 401 1. Of D401~D406 DIODE, check the defective
(V6313) No.11~16 pin switch part.
is not impressed to 2. Check the disconnected line 6point at IC 401
switch. No.11 ~16 pin and D401~D406.
Yes
OK
18
AUDIO CIRCUIT
TROUBLESHOOTING GUIDE
1. ANALOG OUT
CAUTION :
Before checking audio circuit, check configurations on SET UP MENU with the remote control first.
Audio output defect
Is RCA cable
properly connected to
No RCA cables should be 1. Yellow - Video output / Gray - Video input.
signal input edge? connected to 2. Red / White - Audio output or Audio input.
equipment fitting three 3. Black - DIGITAL OUT.
colors.
Yes
Is AUDIO No
waveform of IC804B LM4558 The signal is not 1. The analogue signal must be running at IC804B
IC 7pin yielded? impressed at Loader No.6 and 5 pin.
or amplification is not 2. If analogue signal is running at IC804B, check
made at U13B. the parts mounting status of signal line.
3. If there is no problem at 1. and 2. replace IC.
Yes
Is AUDIO
waveform of IC804A LM4558
No The signal is not 1. The analogue signal must be running at IC804A
IC 1 pin yielded? impressed at Loader No.2 and 3 pin.
or amplification is not 2. If analogue signal is running at IC804A, check
made at U13A. the parts mounting status of signal line.
3. If there is no problem at 1. and 2. replace IC.
Yes
Is AUDIO
waveform of IC803 3 and
No Switching port of IC is 1. At DVD MODE, IC803 No.9 pin must be high
13 pin yielded? not controlled when and No.10 pin must be low.
input status is normal. 2. At AUX MODE, IC803 No.9 and 10 pin must be
low status.
3. If 1. 2. is working normally and +9V is
Yes impressed to IC803 No.16 pin, replace IC.
OK
19
2. DIGITAL OUT
CAUTION : Before checking coaxial circuit, check its connection with Receiver first.
TROUBLESHOOTING GUIDE
Digital out output defect
In Audio SET UP No
of SET UP MENU, SPDIF If SPDIF OUTPUT is Move to SETUP MENU/AUDIO SETUP/
OUTPUT is ON? OFF in SET UP MENU, SPDIF OUTPUT/ ON mode.
Digital out is not
supported at software.
Yes
OK
VIDEO CIRCUIT
CAUTION :
Before checking video circuit, check configurations on SETUP MENU with the remote control first.
Video signal output defect
When video signal No
is running, TV screen is It doesn't match either 1. Move to SETUP MENU/PREFERENCE/TV
properly shown? NTSC/PAL method TYPE MODE.
with TV setting. 2. Match MULTI/NTSC/PAL with TV setting.
Yes
VIDEO signal is No
running at IC802 (NJM2246) Switching port of IC is 1. VIDEO signal must be running at IC802 No.7 pin.
No.7 pin? not controlled when 2. At DVD model, IC802 No.2 pin must be low and
input status is normal. No.4 pin must be high status.
3. If 1. and 2. is normal and +9V is impressed to
No.16 pin, replace IC802.
Yes
OK
20
PCB PATTERN
FRONT PCB
P C B PAT T E R N
21
BOTTOM PCB
P C B PAT T E R N
22
P C B PAT T E R N
23
TOP PCB
PART LIST
bf bm1 bh lm mc dh
EU-AP80P80T-01 AV Input P80/P80T A 01 5PIN pedestal 2.5mm 1
A 02 1*3 three colored output (horizontal) 1
A 03 AVInput board P80/P80T 1
PA RT L IS T
A 04 Fibre cardboard 1
EU-DP80T112-01 Mainboard B 01 Mainboard P80 2004-04-15 1
P80 18- B 02 0603 0.1uF 25V M Y5V 58
P80T112-01 B 03 0603 1000PF K 25V COG 8
B 04 0603 4700PF K 25V COG 4
B 05 0603 1uF M 25V X7R 5
B 06 0603 0.047uF M 25V Y5V 2
B 07 0603 6800PF K 25V COG 1
B 08 0603 560PF 25V J COG 3
B 09 0603 47PF 25V J COG 1
B 10 0603 0.015uF 25V M Y5V 3
B 11 0603 33PF 25V J COG 5
B 12 0603 470PF 25V J COG 7
B 13 0603 0.01uF K 25V COG 3
B 14 0603 820PF 25V J COG 1
B 15 0603 680PF 25V J COG 4
B 16 0603 100PF 25V J COG 3
B 17 0603 0.22uF 10% 50V X7R 2
B 18 0603 160PF 25V J COG 1
B 19 0603 0.033uF 25V K Y5V 1
B 20 0603 150PF 25V J COG 4
B 25 CD110 220u/35V footstool lengh7mm 2
B 26 CD110 10u/25V Dia.5mm 2.0mm footstool lengh7mm 3
B 29 CD110 100u 16V 2.0MM footstool lengh7mm 5X11 17
B 30 CD110 4.7uF/25V H5R4 2.5mm footstool lengh7mm 1
B 31 CD110 220u 16V 2.0mm footstool lengh 7mm 2
B 32 CD110 470uF/16V footstool lengh7mm 2
B 33 CD110 10u/25V Dia.4mm height 5mm footstool lengh 7mm 12
B 34 CD26C 100u 16V Dia.6mmheight 5mm footstool lengh7mm 4
B 35 SRN10 3
B 36 SRN4.7K 1
B 37 0603 10K 5% 1/16W 20
B 38 0603 3.3K 5% 1/16W 10
B 39 0603 4.7K 5% 1/16W 12
B 40 0603 68K 5% 1/16W 1
B 41 0603 20K 5% 1/16W 1
B 42 0603 33K 5% 1/16W 3
B 43 0603 1.2K 5% 1/16W 1
B 44 0603 5.1K 5% 1/16W 2
B 45 0603 6.8K 5% 1/16W 4
B 46 0603 33 5% 1/16W 21
B 47 0603 12K 1% 1/16W 1
25
bf bm1 bh lm mc dh
B 48 0603 12K 5% 1/16W 1
B 49 0603 100K 5% 1/16W 2
PA RT L IS T
B 50 0603 18K 5% 1/16W 3
B 51 0603 0 5% 1/16W 14
B 52 0603 10 5% 1/16W 3
B 53 0603 47K 5% 1/16W 2
B 54 0603 1K 5% 1/16W 17
B 55 0805 1 5% 1/10W 4
B 56 0603 1.5K 5% 1/16W 3
B 57 0603 1M 5% 1/16W 1
B 58 0603 3.3 5% 1/16W 1
B 59 0603 390 5% 1/16W 1
B 60 0603 75 5% 1/16W 7
B 61 0603 100 5% 1/16W 1
B 62 0603 2.2K 5% 1/16W 2
B 63 0603 3K 5% 1/16W 1
B 64 0603 22K 5% 1/16W 2
B 65 0603 180 5% 1/16W 1
B 66 0603 470 5% 1/16W 1
B 67 0603 120 5% 1/16W 2
B 68 0603 200 5% 1/16W 2
B 69 0603 330 5% 1/16W 2
B 70 spool 0805 101 8
B 71 spool 0805 3.3uH 1
B 72 spool 0805 2.4uH 2
B 74 Inductance 10uH/0.5A P80 1
B 75 Inductance winding1mH/1A P80 1
B 76 Inductance winding150uH 6mm 800mA 1
B 77 diode 1N4148 6
B 78 diode SB560 1
B 79 diode SB240 1
B 80 1N5819 1
B 81 diode 1N4007 brede 1
B 82 manostant Z3.6V 1/2W brede 1
B 83 audion A733SOT-223 2
B 84 audion C945 SOT-223 6
B 85 audion 3904 2
B 86 FHK3018 2
B 87 2SB1132QR (SOT89EBC) ROMN SMD 2
B 88 B772 1
B 89 AMS1117 outside 3
B 90 ST7805 TO-220 ST 1
B 91 PQ1CY1032Z 1
B 92 7809 TO220 ST 1
B 93 VT6313 1
26
bf bm1 bh lm mc dh
B 95 NJM2246 1
B 96 CD4052BC SOP16 2 groups 1 in 4 1
PA RT L IS T
B 97 4558 SOP8 ST 1
B 98 ES6629F 1
B 99 BA5954FP ROMN 1
B A1 TL3472 1
B A2 ES6603S 1
B A3 29F800B TSOP -70 1
B A4 24C02 1
B A5 4M*16 SDRAM StarRam 1
B A6 WM8761 1
B A7 455E 1
B A8 27M diode 70 degree (low) 1
B B1 5PIN pedestal 2.0MM 2
B B2 6PIN pedestal 2.0 right angle 1
B B3 4PIN pedestal 2.0MM 90 degree 1
B B4 12Pin pedestal 2.0mm FFC (2.0/2) angle 90 degree 1
B B6 HOP-1200 JP24-0.5mm 1
B B7 single output (black) 1
B B8 1*3three colored output (horizontal) 1
B C1 4Pin power jack 5559-4AW 1
B C2 earphone faucet CKX-3.5-07 five stilts 1
B C3 6287 1
B D1 G686 SOT23 1
EU-EP80P80T-02 Earphone C 01 0805 10K 5% 1/10W 6
P80/P80T W/O 4PIN C 02 CD110 10u/25V dia.4mm high 5mm length 7mm 2
C 03 CD110 47u/16V 5(W)*5(H)mm P80 2
C 04 CD26C 100u 16V dia.6mm high 5mm length 7mm 2
C 05 earphone faucet CKX-3.5-07 five stilts 1
C 06 4PIN wiring2.0mm 60mm P80 1
C 07 LM4808M SOP8 1
C 08 earphone boardP80/P80T 1
EU-FP801-03 Front control panel D 01 RT13 100 J brede 1
P80/P80T 18- D 03 RT13 10K J brede 1
P80T114-01 D 04 Diode1N4148 brede 6
D 05 color light (blue) 3004UB 1
D 06 CD110 47u/16V 5(W)*5(H)mm P80 1
D 07 horizontal touch power6*6*5 6
D 08 5.5MM wire 1
D 09 receiverPIC-331LM 1
D 10 front panel P80/P80T 2004-04-15 1
D 11 12Pin spool FCC 1.0mm 110mm P80 1
EU-FP80F004-01 Front unit E 01 front panel P80 (silver) AKI 1
P80/P80T(silver) AKI E 02 window P80 (silver) 1
E 03 power button P80 1
27
bf bm1 bh lm mc dh
E 04 tray buttonP80 1
E 05 4 keys P80 1
PA RT L IS T
E 06 IR window P80 1
E 07 light pole P80 1
E 08 earphone underlay P80 1
E 09 screwPTPW3*8-HO-9 1
P80 F 02 front control panel P80/P80T 18-P80T114-01 8
F 03 Earphone P80/P80T without 4PIN pedestal 1
F 04 AV input unit P80/P80T 1
F 05 Mainboard P80 18-P80T112-01 2004-04-15 1
F 06 front panel P80/P80T(silver) AKI 1
F 10 loader(DV34) sanyo 1
F 11 P80/P80T KZG-D03 39mm loader bracket SANYO DV34 1
F 12 power cable P80/P80T(1.5m) with DC 1
F 13 P80/P80T IR SENSOR AND CABLE (1.2M) 1
F 14 P80/P80T AV cable (1.2m) 1
F 15 rear P80 AKI (without RF) (electrolytical board) 1
F 16 cover(silk)P80 RIFA 1
F 17 base P80 (electrolytical board) 1
F 18 bracket hook P80 RIFA (silk) 1
F 19 remote controller P80/P80T B004-24 AKI 2
F 21 24Pin wiring FCC 0.5mm 60mm P80 1
F 22 5PIN linker 2.0mm 200mm P80 1
F 23 5PINlinker 2.0mm 250mm P80 1
F 25 footstool P80/P80T 1
F 26 foam top P80/P80T 4
F 27 foam bottom P80/P80T 1
F 30 carton box P80/P80T with 5 sets AKI B004-24 1
F 31 giftbox P80/P80T (neutral) 1
F 33 screw BT3*7BB-HO round3*7(with higher-rigidity) black 1
F 35 screwBT3*6BB-HNi round3*6(with higher-rigidity)nickel-plate 0.200
F 36 screw (TA4*10-HNi) P80/P80T 1
F 37 screwBT3*6FB-HNi 3*6(with higher-rigidity)nickel-plate 4
F 38 6PIN wiring2.0mm 70mm P80 16
F 39 plustic bag (90*60open) 4
F 40 plastic bag (250*95 open) 2
F 41 all paster (15mm) 1
F 42 (80MM) 2
F 45 product serial paster AP001-AP500 1
F 46 Instruction manual P80/P80T neutral 1
F 50 Av wire 1.3M 1
F 51 rear label E4 P80 B004-24 1
F 52 warranty seal :round 1
28
MEMO
29
MEMO
30