Text preview for : Sony KV-42DRC800 service manual.pdf part of Sony KV-42DRC800, KV-32HS500, KV-32HV600, KV-34DRC500 Service Manual Trinitron Colour Television - Remote Commander RM-Y187 (22.715Kb) 7 Part File - pag. 224
Back to : trinitron_color_tv.part01 | Home
Self Diagnosis
Supported model
SERVICE MANUAL
MODEL NAME REMOTE COMMANDER DESTINATION
DA-4
CHASSIS NO.
CHASSIS
KV-42DRC800
RM-Y187
LATIN NORTH
NOT RELEASED
RM-Y186
KV-32HS500
TRINITRON® COLOR TELEVISION
9-965-925-01
Data for Models: KV-32HS500 KV-32HV600 KV-34DRC500
Has been released and is included in this manual.
Preliminary Data is included for other models for your reference. This manual will be updated prior to these models being released.
Please check our web page at http://intranet.sdp.sel.sony.com/servicepromotion/ for the latest manuals as these models are released.
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
TABLE OF CONTENTS
SECTION TITLE PAGE SpeciÞcations ................................................................................. 5 Warnings and Cautions .................................................................. 7 Safety Check-Out ........................................................................... 8 Self-Diagnostic Function................................................................. 9 1. Disassembly 1-1. Rear Cover Removal............................................................ 12 1-2. Chassis Assembly Removal................................................. 12 1-3. Service Position ................................................................... 12 1-4. Picture Tube Removal.......................................................... 13 Anode Cap Removal Procedure .......................................... 13 2. Set-Up Adjustments 2-1. Beam Landing ...................................................................... 14 2-2. V-PIN and V-CEN Adjustment .............................................. 15 2-3. Convergence........................................................................ 15 2-3.1. Vertical and Horizontal Static Convergence............. 15 2-3.2. Operation of BMC (Hexapole) Magnet..................... 15 2-3.3. TLH Plate Adjustment .............................................. 15 2-3.4. Screen-Corner Convergence ................................... 16 2-3.5. Dynamic Convergence Adjustments ........................ 16 2-4. Focus ................................................................................. 17 2-4.1. Dynamic Focus/Dynamic Quadra-Pole Data ........... 17 2-5. Screen (G2).......................................................................... 18 2-6. Picture Quality Adjustments ................................................. 18 2-6.1. Video Input - Sub Contrast Adjustment .................... 18 2-6.2. Video Input - Sub Hue/Sub Color Adjustment .......... 18 2-6.3. RF Input - Two Picture Sub Contrast Adjustment..... 19 2-6.4. RF Input - Sub Hue/Sub Color Adjustment .............. 19 2-7. White Balance (CRT) and Sub Bright Adjustment................ 20 2-7.1. Color Offset Adjustment Procedure.......................... 20 2-8. H Raster Center Adjustment ................................................ 20 2-9. Picture Distortion Adjustments ............................................. 21 2-9.1. NTSC (DRC) Full Mode Adjustment......................... 21 2-9.2. 1080i HD Mode Adjustment ..................................... 21 2-9.3. Vertical Compressed Mode Check and ConÞrmation (For 4 x 3 CRT Only)........................... 22 2-9.4. Twin Mode/Favorite/Index/Normal Mode Geometry ConÞrmation ............................................ 22 3. Safety Related Adjustments 3-1. Preparation Before ConÞrmation ......................................... 23 3-1.1 Hold-Down Operation ConÞrmation ......................... 23 3-2. B+ Max ConÞrmation ........................................................... 23 3-3. HV Service Flowchart........................................................... 24 4. Circuit Adjustments 4-1. Setting Service Adjustment Mode ........................................ 25 4-1.1. Service Adjustment Mode In .................................... 25 4-1.2. Service Adjustment Mode Memory .......................... 25 SECTION TITLE PAGE 4-1.3. Reading the Memory................................................ 25 4-1.4. Adjusting the Picture ................................................ 25 4-1.5. Resetting the Data ................................................... 25 4-1.6. Resetting the MID NVM Data................................... 25 4-1.7. Resetting the System NVM Data ............................. 25 4-1.8. Copy Function .......................................................... 25 4-2. Memory Write ConÞrmation Method .................................... 26 4-3. Remote Adjustment Buttons and Indicators ......................... 26 4-4. Service Data Lists ................................................................ 27 4-4.1. KV-32HS500 Service Data Lists .............................. 27 4-4.2. KV-32HV600 Service Data Lists .............................. 66 4-5. ID Map Table ...................................................................... 101 5. Diagrams 5-1. Circuit Boards Location ...................................................... 102 5-2. Printed Wiring Board and Schematic Diagrams Information ....................................... 102 5-3. Block Diagram and Schematics ......................................... 103 Block Diagrams .................................................................. 103 D Board .............................................................................. 107 M Board............................................................................... 111 U Board ...............................................................................116 MS1 Board ..........................................................................118 HM Board ........................................................................... 122 UD Board ........................................................................... 124 A Board .............................................................................. 126 B Board .............................................................................. 130 DH Board ........................................................................... 138 HB Board............................................................................ 140 HC Board ........................................................................... 142 HA Board............................................................................ 144 CH Board ........................................................................... 146 CX Board............................................................................ 148 W Board ............................................................................. 150 5-4. Semiconductors ................................................................. 152 6. Exploded Views 6-1. Chassis (KV-32HS500/32HV600/34DRC500)..................... 154 6-2. Picture Tube (KV-32HS500/32HV600/34DRC500) ............. 155 6-3. Chassis (KV-34XBR800) ..................................................... 156 6-4. Picture Tube (KV-34XBR800).............................................. 157 6-5. Beznet (KV-34XBR800)....................................................... 158 6-6. Chassis (KV-36HS500/38DRC500)..................................... 159 6-7. Picture Tube (KV-36HS500/38DRC500) ............................ 160 6-8. Chassis (KV-36XBR800) ..................................................... 161 6-9. Picture Tube (KV-36XBR800).............................................. 162 6-10. Chassis (KV-40XBR800/42DRC800) ............................... 163 6-11. Picture Tube (KV-40XBR800/42DRC800) ......................... 164 7. Electrical Parts List ....................................................................... 165
--4--
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
SPECIFICATIONS
KV-32HS500 KV-32HV600 KV-34DRC500 Power Requirements Number of Inputs/Outputs Video 1) S Video 2) Y,PB, PR 3) Audio 4) Audio Out 5) Monitor Out Control-S (In/Out) Memory Stick DVI-HDTV 6) Speaker Output (W) Power Consumption (W) In Use (Max) In Standby Dimensions (W x H x D) mm in Mass kg lbs
KV-34XBR800
KV-36HS500
KV-36XBR800 120V, 60Hz 4 3 2 7 1 1 YES YES 1
KV-38DRC500
KV-40XBR800
KV-42DRC800
7.5W x 2 15W Subwoofer
15W x 2 15W Subwoofer
7.5W x 2 15W Subwoofer 280W 1W
7.5W x 2 15W Subwoofer
898 x 689 x 608 mm 35 3/8 x 27 1/8 x 24 in 80 kg 176.5 lbs
994 x 622 x 591.3 mm 39 3/16 x 24 1/2 x 23 5/16 in 93 kg 206 lbs
1017 x 760 x 643 mm 40 x 30 x 25 3/86 in 104.3 kg 230 lbs
1020 x 790 x 639 mm 40 1/8 x 31 1/8 x 25 1/8 in 109 kg 240 lbs
1093 x 836 x 655 mm 43 1/8 x 33 x 26 1/8 in 136 kg 300 lbs
1) 1 Vp-p 75 ohms unbalanced, sync negative 2) Y: 1 Vp-p 75 ohms unbalanced, sync negative C: 0.286 Vp-p (Burst signal), 75 ohms 3) Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative; PB: 0.7 Vp-p, 75 ohms PR: 0.7 Vp-p, 75 ohms 4) 500 mVrms (100% modulation), Impedance: 47 kilohms 5) More than 408 mVrms at the maximum volume setting (variable) More than 408 mVrms (Þx); Impedance (output): 2 kilohms 6) 3.3V T.M.D.S., 50 ohms
TruSurround is a trademark of SRS Labs, Inc. SRS and the SRS symbol are registered trademarks TM of SRS Labs, Inc. in the United ® States and in select foreign counby SRS tries. SRS and TruSurround are incorporated under license from SRS Labs, Inc. and are protected under United States Patent Nos. 4,748,669 and 4,841,572 with numerous additional issued and pending foreign patents. Purchase of this product does not convey the right to sell recordings made with the TruSurround technology.
SRS (SOUND RETRIEVAL SYSTEM)
The SRS (SOUND RETRIEVAL SYSTEM) is manufactured by Sony Corporation under license from SRS Labs, Inc. It is covered by U.S. Patent No. 4,748,669. Other U.S. and foreign patents pending. The word `SRS' and the SRS symbol are registered trademarks of SRS Labs, Inc. BBE and BBE symbol are trademarks of BBE Sound, Inc. and are licensed by BBE Sound, Inc. under U.S. Patent No. 4,638,258 and 4,482,866.
TruSurround
Design and speciÞcations are subject to change without notice.
--5--
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
Television system
American TV standard, NTSC
Channel coverage
VHF: 2-13/ UHF: 14-69/ CATV: 1-125
Picture tube
Flat Trinitron tube
®
Visible screen size
32-inch picture measured diagonally (KV-32HS500/32HV600/34DRC500/Only) 34-inch picture measured diagonally (KV-34XBR800 Only) 36-inch picture measured diagonally (KV-36HS500/36XBR800/38DRC500 Only) 40-inch picture measured diagonally (KV-40XBR800/42DRC500 Only)
Actual screen size
34-inch measured diagonally (KV-32HS500/32HV600/34DRC500/Only) 36-inch measured diagonally (KV-34XBR800 Only) 38-inch measured diagonally (KV-36HS500/36XBR800/38DRC500 Only) 42-inch measured diagonally (KV-40XBR800/42DRC500 Only)
Antenna
75 ohm external terminal for VHF/UHF
Supplied Accessories
Remote Commander RM-RM-Y186 (KV-32HS500/34DRC500/36HS500/38DRC500 Only) Remote Commander RM-RM-Y187 (KV-32HV600/36XBR800/40XBR800/42DRC800 Only) Remote Commander RM-RM-Y188 (KV-34XBR800 Only) Two Size AA (R6) Batteries
Optional Accessories
Connecting cables: RK-74A, VMC-810S/820/830HGS, VMC-720M,VMC-810S/820S, YC-15V/30V, YC-15/30HG, RKG69HG, RKC-515HG (KV-32HS500/32HV600/34DRC500/34XBR800/36HS500/36XBR800/38DRC500 Only) Connecting cables: VMC-10/30HG, VMC-810S/820/830HGS, VMC-810S/820S, RKG69HG, RKC-515HG (KV-40XBR800/42DRC500 Only) AV Cable: VMC-810/820/830 HG (KV-34XBR800 Only) Audio Cable: RKC-515HG (KV-34XBR800 Only) S-LINK Cable: RK-G69HG Component Video Cable: VMC-10/30 HG U/V mixer: EAC-66 (KV-32HS500/32HV600/34DRC500/34XBR800/36HS500/36XBR800/38DRC500 Only) TV Stand: TV Stand: TV Stand: TV Stand: TV Stand: SU-32HS2 (KV-32HS500/32HV600 Only) SU-34HD2 (KV-34XBR800 Only) SU-36HS2 (KV-36HS500 Only) SU-36XBR45 (KV-36XBR800/38DRC500 Only) SV-40XBR7 (KV-40XBR800/42DRC500 Only)
--6--
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
WARNINGS AND CAUTIONS
CAUTION
Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield, or carbon painted on the CRT, after removing the anode.
WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis. The chassis of this receiver is directly connected to the ac power line.
! SAFETY-RELATED COMPONENT WARNING!!
Components identiÞed by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identiÞed in this manual. Follow these procedures whenever critical components are replaced or improper operation is suspected.
ATTENTION!!
Apres avoir deconnecte le cap de l'anode, court-circuiter l'anode du tube cathodique et celui de l'anode du cap au chassis metallique de l'appareil, ou la couche de carbone peinte sur le tube cathodique ou au blindage du tube cathodique.
AÞn d'eviter tout risque d'electrocution provenant d'un chássis sous tension, un transformateur d'isolement doit etre utilisé lors de tout dépannage. Le chássis de ce récepteur est directement raccordé à l'alimentation du secteur.
! ATTENTION AUX COMPOSANTS RELATIFS A LA SECURITE!!
Les composants identiÞes par une trame et par une marque ! sur les schemas de principe, les vues explosees et les listes de pieces sont d'une importance critique pour la securite du fonctionnement. Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l'importance est critique pour la securite du fonctionnement sont identiÞes dans le present manuel. Suivre ces procedures lors de chaque remplacement de composants critiques, ou lorsqu'un mauvais fonctionnement suspecte.
--7--
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or touching high-wattage resistors. 3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators. 4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 7. Check the B+ and HV to see if they are speciÞed values. Make sure your instruments are accurate; be suspicious of your HV meter if sets always have low HV. 8. Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. Leakage Test The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instructions. 2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low voltage scale. The Simpson's 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).
How to Find a Good Earth Ground A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also at earth ground. If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms. If a cold-water pipe is not accessible, connect a 60- to 100-watt troublelight (not a neon lamp) between the hot side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the lamp should light at normal brilliance if the screw is at ground potential (see Figure B).
To Exposed Metal Parts on Set
g AC Outlet Box
AC Voltmeter (0.75 V)
Ohmmeter
0.15 µF
1.5 k
Cold-water Pipe
Earth Ground
Figure A. Using an AC voltmeter to check AC leakage.
Figure B. Checking for earth ground.
--8--
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
SELF-DIAGNOSTIC FUNCTION
Self Diagnosis
Supported model
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER LED will automatically begin to ßash. The number of times the LED ßashes translates to a probable source of the problem. A deÞnition of the STANDBY/TIMER LED ßash indicators is listed in the instruction manual for the user's knowledge and reference. If an error symptom cannot be reproduced, the Remote Commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur. Diagnostic Test Indicators When an error occurs, the STANDBY/TIMER LED will ßash a set number of times to indicate the possible cause of the problem. If there is more than one error, the LED will identify the Þrst of the problem areas. Results for all of the following diagnostic items are displayed on screen. If the screen displays a "0", an error has occurred.
Diagnostic Item Power does not turn on No. of times STANDBY / TIMER lamp flashes Does not light Display Result _______ Probable Cause Location · Power cord is not plugged in. · Fuse is burned out (F501). (A Board) · H.OUT (Q5030) is shorted. (D Board) · +B PWM (Q5003) is shorted. (D Board) · IC6505 is faulty. (D Board) · 15V is not supplied. (D Board) · IC5004 is faulty. (D Board) · · · · · Detected Symptoms Power does not come on. No power is supplied to the TV. AC Power supply is faulty. Power does not come on. Load on power line shorted.
+B Overcurrent (OCP)*
2 times
2:0 or 2:1
Low +B Overvoltage (OVP) Vertical Deflection Stopped
3 times 4 times
3:0 or 3:1 4:0 or 4:1
White Balance Failure (not balanced)
5 times
5:0 or 5:1
LOW +B OCP/OVP (overcurrent/overvoltage)*** Horizontal Deflection Stopped
6 times
6:0 or 6:1
· Video OUT (IC9001-IC9003) is faulty. (CH, CX Board) · CRT drive (IC2801) is faulty. (B Board) · G2 is improperly adjusted.** · +5 line is overloaded. (A, B, M Boards) · +5 line is shorted. (A, B, M Boards) · IC504 is faulty. (A Board)
· Has entered standby mode. · Has entered standby mode after Horizontal raster. · Vertical deflection pulse is stopped. · Power line is shorted or power supply is stopped. · No raster is generated. · CRT cathode current detection reference pulse output is small. · No picture
7 times
7:0 or 7:1
· No picture
* If a +B overcurrent is detected, stoppage of the vertical deflection is detected simultaneously. The symptom that is diagnosed first by the microcontroller is displayed on the screen. ** Refer to Screen (G2) in Section 2-5 of this manual. *** If STANDBY/STEREO LED flashes six (6) times, unplug the unit and wait 10 seconds before performing the adjustment.
Display of Standby/Timer LED Flash Count
Diagnostic items +B Overcurrent Low +B Overvoltage Vert. Deflection Stopped White Balance Failure Low +B OCP/OVP Horiz. Deflection Stopped Flash count 2 times 3 times 4 times 5 times 6 times 7 times
Standby/Timer LED
Lamp OFF 3 sec.
Lamp ON 0.3 sec. Lamp OFF 0.3 sec.
* One ßash count is not used for self-diagnostic.
Stopping the Standby/Timer LED Flash Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER LAMP from ßashing.
--9--
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
Self-Diagnostic Screen Display For errors with symptoms such as "power sometimes shuts off" or "screen sometimes goes out" that cannot be conÞrmed, it is possible to bring up past occurrences of failure on the screen for conÞrmation. To Bring Up Screen Test In standby mode, press buttons on the Remote Commander sequentially, in rapid succession, as shown below: DISPLAY Channel 5 Sound volume Power ON. SELF DIAGNOSIS 2: +B OCP 3: +B OVP 4: VSTOP 5: AKB 6: LOWB 7: H-STOP 101: WDT
0 0 0 1 0 0 24
Numeral "0" means that no fault was detected. Numeral "1" means a fault was detected one time only.
Handling of Self-Diagnostic Screen Display Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen during repairs. When you have completed the repairs, clear the result display to "0". Unless the result display is cleared to "0", the self-diagnostic function will not be able to detect subsequent faults after completion of the repairs. Clearing the Result Display To clear the result display to "0", press buttons on the Remote Commander sequentially when the diagnostic screen is displayed, as shown below: Channel 8 ENTER
Quitting the Self-Diagnostic Screen To quit the entire self-diagnostic screen, turn off the power switch on the Remote Commander or the main unit. Self-Diagnostic Circuit
M
IC2300 MAIN MICRO STBY-LED 48 44 45 43 STR STBY-LED OCP OVP LOW B ERR AC RLY 69 1 4 CLKO DATO 29 30 26 25
IC2801 Y/C JUNGLE AKB SCL VPROT SDA HPROT 58 35 34
M
CRT VDY-
R5104
R5105
B
R5125
5V
RY6501
P_SW(-) 2 3
Q5018
2 IC5007 14
D
IC6505
2
Q6530
Q6527
D
Q6532
D6537
Q6522
1K-PROT2 +B OVP UNREG 11V
4
PH6501
1
+B
1 3
A
IC504 5V O O I UNREG 7V
3
2
D6505
R5013
HV PROT
D5007
+B
+B
D
Q5004 D5005
+B OCP
-- 10 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
+B overcurrent (OCP) Occurs when excessive current ßows through R5013. The increase in voltage across R5013 causes the output of Q5004 to go high, and this high signal goes to the micro. +B overvoltage (OVP) IC6505 detects +B OVP condition and turns on Q6522. This sends a high signal to the micro and also shuts down the AC relay. V-STOP Occurs when an absence of the vertical deßection pulse is detected by pin 24 of IC2801 (B Board). Power supply will shut down when waveform interval exceeds 2 seconds. White Balance Failure If the RGB levels* do not balance within 2 seconds after the power is turned on, this error will be detected by IC2801. TV will stay on, but there will be no picture. *(Refers to the RGB levels of the AKB detection Ref pulse that detects 1K). Low B OCP/OVP Occurs when set 5V is out. Horizontal Deßection Stopped Occurs when either: 1) a +B overcurrent is detected (IC5007), or 2) overheating is detected (Thermistor TH5002).
-- 11 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
SECTION 1: DISASSEMBLY 1-1. REAR COVER REMOVAL
4 Screws +BVTP 4 x 16
Rear Cover 4 Screws +BVTP 4 x 16
6 Screws +BVTP 4 x 16
1-2. CHASSIS ASSEMBLY REMOVAL
1-3. SERVICE POSITION
1 1
Lift lever up on the right and left sides of the chassis bracket and gently pull the chassis assembly away from the bezel. Pull up and rotate both the A and D Boards in order to service the unit.
CAUTION! - Heat sink on IC5004 is -15V. Care must be taken not to allow heat sink to touch any other components. Lift lever up on the right and left sides of the chassis bracket and gently pull the chassis assembly away from the bezel. Pull up and rotate both the A and D Boards in order to service the unit. When plugging in connector from MS Board to B Board at CN3603 insure two brown wires are facing upward towards neck assembly.
2 3
2
4
-- 12 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
1-4. PICTURE TUBE REMOVAL
WARNING: BEFORE REMOVING THE ANODE CAP High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. Short between anode and CRT coated earth ground strap. 1 8
Coated Earth Ground Strap
11 9
7 3 6 4
2
10
1. Discharge the anode of the CRT and remove the anode cap. 2. Unplug all interconnecting leads from the deflection yoke, neck assembly, degaussing coils and CRT grounding strap. 3. Remove the Sub-Woofer Assemblies. 4. Remove the CH or CX Board from the CRT. 5. Remove the chassis assembly. 6. Loosen the neck assembly fixing screw and remove. 7. Loosen the deflection yoke fixing screw and remove. 8. Place the set with the CRT face down on a cushion and remove the degaussing coil holders. 9. Remove the degaussing coils. 10. Remove the CRT grounding strap and spring tension devices. 11. Unscrew the four CRT fixing screws [located on each CRT corner] and remove the CRT [Take care not to handle the CRT by the neck].
5
ANODE CAP REMOVAL PROCEDURE
WARNING: High voltage remains in the CRT even after the power is disconnected. To avoid electric shock, discharge CRT before attempting to remove the anode cap. After removing the anode cap, short circuit to either the metal chassis, CRT shield, or carbon painted on the CRT. NOTE: After removing the anode cap, short circuit the anode of the picture tube and the anode cap to either the metal chassis, CRT shield or carbon painted on the CRT.
REMOVAL PROCEDURES
c
a
b
Anode Button
Turn up one side of the rubber cap in the direction indicated by arrow a .
Use your thumb to pull the rubber cap firmly in the direction indicated by arrow b .
HOW TO HANDLE AN ANODE CAP
1. Do not use sharp objects which may cause damage to the surface of the anode cap. 2. To avoid damaging the anode cap, do not squeeze the rubber covering too hard. A material fitting called a shatter-hook terminal is built into the rubber. 3. Do not force turn the foot of the rubber cover. This may cause the shatter-hook terminal to protrude and damage the rubber.
When one side of the rubber cap separates from the anode button, the anode cap can be removed by turning the rubber cap and pulling it in the direction of arrow c .
-- 13 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
SECTION 2: SET-UP ADJUSTMENTS
The following adjustments should be made when a complete realignment is required or a new picture tube is installed. These adjustments should be performed with rated power supply voltage unless otherwise noted. The controls and switch should be set as follows unless otherwise noted:
Perform the adjustments in order as follows: 1. Beam Landing 2. Convergence 3. Focus 4. Screen (G2) 5. White Balance Test Equipment Required: 1. Color Bar Pattern Generator 2. Degausser 3. DC Power Supply 4. Digital Multimeter 5. Move the deflection yoke forward, and adjust so that the entire screen becomes green.
VIDEO MODE:
STANDARD (RESET)
2-1. BEAM LANDING
Preparation: · Use cross hatch signal to rough adjust focus, G2 and then input a white pattern signal. · Face the picture tube in an East or West direction to reduce the influence of geomagnetism. · Confirm data in service mode to match with CRT screen size. · CXA2170D-4 · CXA8070 (Should be set to default) · VCEN, VPIN, HTPZ, PPHA, VANG, LANG, VBOW, LBOW (Should be set to default value). NOTE: Do not use the hand degausser; it magnetizes the CRT . 1. Input white pattern from pattern generator. Set the PICTURE control to maximum, and the BRIGHTNESS control to standard. 2. Loosen the deflection yoke mounting screw, and set the purity control to the center as shown below:
Purity Control
Figure 1 6. Switch over the raster signal to red and blue and confirm the condition. 7. When the position of the deflection yoke is determined, tighten it with the deflection yoke mounting screw. 8. If landing at the corner is not right, adjust it by using the disk magnets.
Purity control corrects this area
Disk magnets or rotatable disk magnets correct these areas (a-d)
a c
b d
Deflection yoke positioning corrects these areas
b
3. Input a green pattern from the pattern generator. 4. Move the deflection yoke backwards, (See Figure 1) and adjust with the purity control so that green is in the center and red and blue are even on both sides.
d a
c
Blue
Red
Green
-- 14 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
2-2. V-PIN AND V-CEN ADJUSTMENT
Preparation: · Input a cross hatch pattern signal. · Set Video Mode to: Standard (Reset) · For all 4X3 CRT, VPIN data has separate register for full and V-compress. Adjust both modes if needed. 1. Adjust service mode CXA2170D-1 05 V-CEN so that the top pin and bottom pin are symmetrical from top to bottom. 2. Adjust service mode CXA2170D-1 06 V-PIN so that the top pin and bottom pin are symmetrical from top to bottom. 3. Horizontal lines should be straight from left to right. Check landing for side effect.
2-3.2. OPERATION OF BMC (HEXAPOLE) MAGNET
The respective dot positions result from moving each magnet interact. Perform the following adjustments while tracking. 1. Use the BMC tabs to adjust the red, green and blue dots so that they line up at the center of the screen (move the dots in a horizontal direction).
HMC Correction AB GB R A B
R G B
R G B
2-3. CONVERGENGE
Preparation: · Set the CONTRAST and BRIGHTNESS control to standard (reset). · Input a cross hatch pattern signal.
2-3.1. VERTICAL AND HORIZONTAL STATIC CONVERGENCE
1. Disconnect the dynamic convergence before adjusting static convergence (CN903), except for minor touch-up. 2. Adjust H.STAT convergence, RV9001, to converge red, green, and blue dots in the center of the screen. 3. Connect dynamic convergence back. 4. Adjust V. STAT magnet to converge red, green and blue dots in the center of the screen.
C
2-3.3. TLH PLATE ADJUSTMENT
Preparation: · Input a cross hatch pattern signal. · Adjust unbalanced horizontal convergence of red and blue dots by adjusting the TLH Plate on the deflection yoke.
TLV
Center dot
R G B
R G B
RV9001 H-STAT
C Board TLH Plate
RV9001
V.STAT magnet
5. Tilt the V.STAT magnet and adjust static convergence to open or close the V.STAT magnet.
W Board
XCV
1
B G R
B G R
BR (R)(B)
RB (B)(R)
TLH+ TLH-
1. Adjust XCV core to balance X axis. 2. Adjust the vertical red and blue convergence with V.TILT (TLV VR). Note: Perform adjustments while tracking Item 1.
-- 15 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
2-3.4. SCREEN-CORNER CONVERGENCE
Preparation: · Input a cross hatch pattern signal. 1. Affix a permalloy assembly corresponding to the misconverged areas.
b a
2. RSAP (Right H AMP)
RB
3. RUBW (Right Upper BOW)
BR
a
b
a-d: screen-corner misconvergence c c d
4. RUMB (Right Upper Middle BOW)
BR
d
2-3.5. DYNAMIC CONVERGENCE ADJUSTMENTS
· Set dynamic convergence using the following service mode adjustment data. · Only H-component can be corrected, for vertical component use permalloy to compensate. · After adjusting the following parameter, write data into NVM MUTING + ENTER then copy for 1080i CPY2 (D Conv Item 13 - Change data to 1 then write.)
5. RLBW (Right Lower BOW)
R B
6. RLMB (Right Lower Middle BOW)
BR
7. LSAP (Left H AMP)
BR
8. LUBW (Left Upper BOW)
B R
0. YBWU (Upper Y-BOW)
B R B R
9. LUMB (Left Upper Middle BOW)
BR
1. YBWL (Lower Y BOW) 10. LLBW (Left Lower BOW)
B R
B R
BR
-- 16 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
11. LLMB (Left Lower Middle BOW)
2-4.1. DYNAMIC FOCUS/DYNAMIC QUADRAPOLE DATA
Normally, no adjustments are necessary for these systems. If for some reason the data is lost, use the following data:
BR
12. CADJ Fix 29
2-4. FOCUS ADJUSTMENT
Confirm neck assembly Z axis position. (See Figure 1) 1. Input a dot signal. 2. Set Video Mode to STANDARD. 3. Adjust focus VR clockwise (DE-Focus) to confirm that the dot's shape is centered. (Figure 2 & 3) Confirm neck assembly rotation by W Board position. W Board should be level ±1º. Adjust as necessary to balance dot shape along center horizontal line, then refocus. 4. Input a HD monoscope signal. 5. Confirm center focus with focus VR.
Write the data from any non-vertically compressed mode, then use the CPY1 function (CXA2170D-4 Item 6) to copy the data to the vertical compressed modes. V-compressed data is identical to non-v-compressed data. Service personnel with a trained eye can adjust the DF or DQP registers to adjust DF phase (Item 7) or DQP phase (Item 8), respectively, to balance left and right focus. Refrain from adjusting more than 5 steps from table data below. Further adjustment indicates a circuit problem -- troubleshoot to cause. Be sure that Neck Assembly is in the proper location (See Section 2-4 Figure 1) before changing DF/DQP data or troubleshooting circuit when DF/DQP is suspect.
Figure 1
FOCUS Screen (G2)
Figure 2
DOT SHAPE:
Figure 3 NOTE: Changing neck assembly position will affect corner convergence.
-- 17 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
2-5. SCREEN (G2)
1. Input composite white field into Video 1. 2. Set to service mode and adjust as follows:
2-6. PICTURE QUALITY ADJUSTMENTS
Preparation: · Set PRO MODE (Reset). 1. Input signal (480i Composite): · Color Bar Video 75 IRE (White) 75% modulation 7.5% Set-up. · Color Bar RF 75 IRE (White) 75% modulation 7.5% Set-up.
white VR1 black VR2 GND
VR (32HS) = 1.92 ± 0.05 Vpp (36HS) = 2.00 ± 0.05 Vpp (32HV) = 1.67 ± 0.05 Vpp (34XBR) = 1.67 ± 0.05 Vpp (36XBR) = 1.74 ± 0.05 Vpp (40XBR) = 1.81 ± 0.05 Vpp 4. Write data from Step 3 above, into memory.
2-6.1. VIDEO INPUT - SUB CONTRAST ADJUSTMENT
Preparation: · Input a Color Bar signal to VIDEO 1 (75 IRE 75%). · Set picture mode: Single (PRO MODE Reset). · Picture: Max 1. Set to Service Mode and adjust as follows: 2150P-2 NO. Name 01 RGBS Control Function R ON Avg. Data 4
2-6.2. VIDEO INPUT - SUB HUE/SUB COLOR ADJUSTMENT
Preparation: · Input a Color Bar signal to VIDEO 1 (75 IRE 75%). · Set picture mode: Single (PRO MODE Reset). · Picture: Max 1. Set to Service Mode and adjust as follows: 2150P-2 NO. Name 01 RGBS Control Function R ON Avg. Data 7
2. Connect oscilloscope to Pin 1 of CN9001 (R.DRV) on the C Board. 3. Adjust contrast according to the service mode item: SPIO. 2103-2 NO. Name 02 SCON Control Function SUB-CONT
2. Connect an oscilloscope to Pin 5 of CN9001 (B. DRV) on the C Board.
-- 18 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
3. Adjust color according to Service Mode for SCLO. 4. Adjust color according to Service Mode for SHUO. 2103-1 NO. Name 03 SCOL 04 SHUE Control Function SUB-COL SUB-HUE
white VR1 black VR2 GND
VB4 VB1 VB2 VB3
COLOR: VB1 < VB4 (=20 ± 40 mV) HUE: VB2 < VB3 (=20 ± 40 mV) 7. Write data into memory.
VR (32HS) = 1.92 ± 0.05 Vpp (36HS) = 2.00 ± 0.05 Vpp (32HV) = 1.67 ± 0.05 Vpp (34XBR) = 1.67 ± 0.05 Vpp (36XBR) = 1.74 ± 0.05 Vpp (40XBR) = 1.81 ± 0.05 Vpp 5. Write data from Steps 3 - 4 above, into memory. 6. Set Service Mode 2170P-4 NO. Name 28 SPOF Control Function Avg. Data SMALL PICTURE OFFSET 13
2-6.3. RF INPUT - TWO PICTURE SUB CONTRAST ADJUSTMENT
Preparation: · Input a Color Bar signal to RF (75 IRE 75%). · Set picture mode: P&P (PRO MODE). · Picture: Max 1. Set to Service Mode and adjust as follows: 2170P-4 NO. Name 28 SPOF 2170P-2 NO. Name 01 RGBS Control Function R ON Avg. Data 4 Control Function Avg. Data SMALL PICTURE OFFSET 0
2-6.4. RF INPUT - SUB HUE/SUB COLOR ADJUSTMENT
Preparation: · Input a Color Bar signal to RF (75 IRE 75%). · Set picture mode: P&P (PRO MODE Reset). · Picture: Max 1. Set to Service Mode and adjust as follows: 2150P-4 NO. Name 01 RGBS Control Function R ON Avg. Data 7
2. Connect an oscilloscope to Pin 1 of CN9001 (R. DRV) on the C Board. 3. Adjust MAIN (left) side contrast according to service mode for SCON. 2103-1 NO. Name 02 SCON Control Function SUB-CONT
2. Connect an oscilloscope to pin 5 of CN9001 (B. DRV) on the C Board. 3. Adjust MAIN (left) side color according to Service Mode for SCOL. 4. Adjust MAIN (left) side color according to Service Mode for SHUE. 2103-1 NO. Name 03 SCOL 04 SHUE Control Function SUB COLOR SUB HUE
4. Adjust SUB (right) side contrast according to Service Mode for SCON. 2103-2 NO. Name 02 SCON Control Function SUB-CONT
5. Adjust SUB (right) side color according to Service Mode for SCOL.
-- 19 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
6. Adjust SUB (right) side color according to Service Mode for SHUE. 2103-2 NO. Name 03 SCOL 04 SHUE Control Function SUB COLOR SUB HUE
2-7.1. COLOR OFFSET ADJUSTMENT PROCEDURE
Preparation: · Input an all white (30 IRE) signal to the specified input. · Adjust the white balance using the specified registers.
VB4 VB1 VB2 VB3
VIDEO 1 CXA2103-M NO. Name 20 CBO1 21 CRO1 VIDEO 5 CXA2103-M NO. Name 20 CBO1 21 CRO1 VIDEO 7 - DVI CXA2103-M NO. Name 22 CBO2 23 CRO2
Control Function CB OFFSET CR OFFSET
COLOR: VB1 < VB4 (=20 ± 40 mV) HUE: VB2 < VB3 (=20 ± 40 mV) 7. Write data into memory.
Control Function CB OFFSET CR OFFSET
2-7. WHITE BALANCE (CRT) AND SUB BRIGHT ADJUSTMENT
Preparation · Input an all white 480I (15.734 KHz) signal into the VIDEO 1 input terminal to perform the White Balance (highlight, cut-off) adjustments. The parameters to adjust are in the CXA2170P in Service Mode.
Control Function CB01 (FROM VIDEO 5) - 5 CR01 (FROM VIDEO 5) -4
2-8. H RASTER CENTER ADJUSTMENT
Preparation: · Input a monoscope signal. · Set to NTSC (DRC) mode. 1. Set to Service Mode and adjust as follows:
CXA2170P-2 NO. Name 05 AGNG CXA2170D-2 NO. Name 01 HPOS 02 HSIZ CXA2170D-3 NO. Name 00 HBLK Control Function Blanking Enable Avg. Data 0 Control Function Horiz Position Horiz Size Avg. Data 34 34 Control Function AGING 1, AGING 2 Data 2
2. 3. 4. 5.
Reduce HSIZ to see sides of raster. Adjust H-Center with CXA2170D-2. Adjust to the best screen position with H-CENT and write data. Restore aging, HSIZ and HBLK to original condition.
-- 20 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
Raster Edge Equal: RASTER EDGES Item 5. PIN (PIN AMP) RASTER Item 2. HSIZ (H-SIZE)
2-9. PICTURE DISTORTION ADJUSTMENTS 2-9.1. NTSC (DRC) FULL MODE ADJUSTMENT
1. Face the picture tube in an east-west direction. (For best condition.) 2. Complete V-PIN and V-CEN adjustments first (A2170-D1 06 V-PIN, A2170-D1 05 V-CEN). 3. Input a monoscope and crosshatch signal. Adjust the picture distortion with the following service parameters to balance the best condition for these two signals. NOTE: Make sure that the picture size is within specs. Vertical size is 11.8 ± 0.1 sq. and horizontal size is 15.8 ± 0.1 sq. 4. Write data into memory before changing modes.
Item 7. UCP (UP COR PIN COR)
Item 8. LCP (LOW CO PIN COR)
Item 14. PPHA (PIN PHASE)
Item 15. VANG (AFC-ANGLE)
CXA2170D-1
Item 0. VPOS (V-POSITION)
Item 16. LANG (L-ANGLE)
Item 17. VBOW (AFC-BOW) Item 1. VSIZ (V-SIZE)
Item 18. LBOW (L-BOW) Item 3. VLIN (V-LINE)
Item 4. VSCO (VS-COR)
2-9.2. 1080i HD MODE ADJUSTMENT
1. Input a 1080i cross-hatch signal and an HD monoscope signal that contains overscan markers. 2. Adjust the raster position per Section 2-8., only if this procedure was not performed for full mode. 3. Adjust the geometry similar to Full DRC mode. Vertical size is 11.7 ± 0.1 sq. and horizontal size is 15.6 ± 0.1 sq., if monoscope signal is available. Otherwise, set the Vertical size to 91.0 ± 0.6% scan and Horizontal size as 91.0 ± 0.6% scan. 4. Use the following register to adjust the horizontal parameter: A2150-D2 NOTE: 01 HPOS
Item 9. HTPZ (H-TRAPEZOID)
CXA2170D-2
Item 1. HPOS (H-POSITION)
If necessary, touch up the geometry using the data register listed above for Full mode. Check NTSC full mode for side effect and balance. 5. Write the data into memory before changing modes.
-- 21 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
2-9.3. VERTICAL COMPRESSED MODE CHECK AND CONFIRMATION (FOR 4X3 CRT ONLY)
1. Input a monoscope and crosshatch signal. 2. Check vertical compressed mode. 3. Adjust VPIN if needed.
2-9.4. TWIN MODE/FAVORITE/ INDEX/NORMAL MODE GEOMETRY CONFIRMATION
TWIN mode and FAVORITE mode use the FULL mode adjustment data. The key point for TWIN mode adjustment is the blue border appearance. The left border on the left picture should not be visible when the left picture is selected. Similarly, the right border on the right picture should not be visible when the right picture is selected. Balance the HPOS or HSIZ data for FULL and TWIN mode. For INDEX mode, however, (XBR sets only), no clipping of the picture edge should be visible for the small sampled pictures on the right side. Adjust HSIZ/HPOS to balance FULL and INDEX mode for this. Avoid displaying the edge of the raster in FULL or FAVORITE mode.
-- 22 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
SECTION 3: SAFETY RELATED ADJUSTMENTS 3-1. PREPARATION BEFORE CONFIRMATION
Standard............................................................................. 135.3 ± 1 VAC Check Condition: AC input voltage: 120 (± 2) VAC Note: If using a stabilized power supply, make sure that the distortion factor is 3% or less. Setting Mode:........................................................................... Full mode Signal Input:...........................................................Cross-hatch of NTSC Initial Setting:...................................................Standard Reset condition ConÞrm Point:..........................Across CN5509 PIN 9 for B+ of D Board
3-2. B+ MAX CONFIRMATION
Standard............................................................................. 135.3 ± 1 VAC Check Condition: AC input voltage: 120 (± 2) VAC Note: If using a stabilized power supply, make sure that the distortion factor is 3% or less. Setting Mode:........................................................................... Full mode Signal Input:...........................................................Cross-hatch of NTSC Initial Setting:...................................................Standard Reset condition ConÞrm Point:..........................Across CN5509 PIN 9 for B+ of D Board
3-1.1 HOLD-DOWN OPERATION CONFIRMATION
1. Using an external DC power supply, apply 5.3 ± 0.5 Vdc between Pin 2 of CN507 (jig connector) and ground (Pin 8); confirm set goes to hold-down (main power relay click). 2. Remove the external DC power supply.
-- 23 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
3-3. HV SERVICE FLOWCHART
-- 24 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
SECTION 4: CIRCUIT ADJUSTMENTS ELECTRICAL ADJUSTMENTS BY REMOTE COMMANDER
Use the Remote Commander (RM-Y170, RM-Y171) to perform the circuit adjustments in this section. Test Equipment Required: 1. Pattern generator 2. Frequency counter 3. Digital multimeter 4. Audio oscillator
4-1. SETTING SERVICE ADJUSTMENT MODE
1. Standby mode (Power off). 2. Press the following buttons on the remote commander within a second of each other: Channel 5 Sound Volume + Power DISPLAY
4-1.3. READING THE MEMORY
1. Enter into Service Mode. 2. Press 0 on the Remote Commander. 3. Press ENTER to read memory.
4-1.4. ADJUSTING THE PICTURE
1. 2. 3. 4. 5. Enter into Service Mode Press 2 or 5 on the remote to select the device item. Press 1 or 4 on the remote to select an item. Press 3 or 6 on the remote to change the data. Press MUTING then ENTER to write into memory.
4-1.1. SERVICE ADJUSTMENT MODE IN
Disp. (Item) Item order Item data
VP HSIZ
0
7 TV
SERVICE
Mode
4-1.5. RESETTING THE DATA
Note: Be careful when using the remote! It will clear and re-initialize ALL NVM data including deflection adjustment data if not reset properly as follows:
3. 4. 5. 6.
The CRT displays the item being adjusted. Press 1 or 2 on the Remote Commander to select the item. Press 3 or 6 on the Remote Commander to change the data. Press MUTING then ENTER to write into memory.
4-1.6. RESETTING THE MID NVM DATA
1. Enter into Service Mode. 2. Press 7 , then JUMP , and then press ENTER on the remote.
4-1.2. SERVICE ADJUSTMENT MODE MEMORY
Disp. (Item) Item order Item data
4-1.7. RESETTING THE SYSTEM NVM DATA
1. Enter into Service Mode. 2. Press 7 , then 9 , and then press ENTER on the remote.
4-1.8. COPY FUNCTION
MUTING Green How to use copy function for DA4 Chassis: · After writing your adjusted data into NVM MUTING then ENTER , copy can be made by changing copy data from 0 to 1 then MUTING , ENTER again. WARNING: DO NOT copy data before writing your corrected data in NVM. If data is copied before writing corrected data, old data will be copied. · CPY1: DF/DQP DATA (CXA2170D-4 Item 6) · CPY2: CONVERGENCE DATA (D-CONV Item 13)
VP HSIZ
0
7 TV
SERVICE
ENTER Red 7. Press then on the Remote Commander to initialize.
Disp. (Item) Item order Item data
VP HSIZ
0
7 TV
WRITE
8. DO NOT turn off set until SERVICE appears.
-- 25 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
4-2. MEMORY WRITE CONFIRMATION METHOD
1. After adjustment, pull out the plug from the AC outlet, then replace the plug in the AC outlet again. 2. Turn the power switch ON and set to Service Mode. 3. Call the adjusted items again to confirm they were adjusted.
4-3. REMOTE ADJUSTMENT BUTTONS AND INDICATORS
MUTING
(Enter into memory)
POWER
(Service Mode)
DISPLAY
(Service Mode) 3 Item (Data Up) 6 Item (Data Down) 5 (Device Item Down)
1 Disp. (Item up) 2 (Device Item Up) Disp. 4 (Item Down)
ENTER
(Enter into Memory) 0 (Remove from Memory)
8 (Initialize)
VOLUME (+)
(Service Mode)
RM-Y186
-- 26 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
4-4. SERVICE DATA LISTS 4-4.1. KV-32HS500 SERVICE DATA LISTS
Category Name VERSION No. 0 1 0 1 2 3 4 5 6 7 Item Name VER DMY1 NRMD CLKS NSDS MSS KILS FRZE EXCS CDL
Range 0,1 0-255 0-3 0-3 0-3 0-3 0-3 0, 1 0-3 0-7 0-15 0-15 0-15 0-15 0-2 0, 1 0-7 0-31 0, 1
Initial Data 0 0 0 1 0 0 1 0 1 4 NRMD(0) 2 10 5 5 1 0 Vivid 4 4 0 Vivid RF 3 7 0 1 1 0 0 0 Standard RF 3 7 Movie CV/YC 3 6 Pro CV/YC 3 5 TWIN Any 3 6 Standard 2 4 Movie 2 4 Pro 0 0 NRMD(1) 2 10 5 5 NRMD(2) 2 10 5 5 NRMD(3) 2 10 5 5
8 9 10 11 12 13 3D_COMB 14 15 16
DYCO DYGA DCCO DCGA WSC WSS
VAPG VAPI TEST
17 18 19 20 21 22 23 24
YPFT YPFG SEDC SEDY YHCO YHCG SYSP TES2
0-3 0-15 0, 1 0, 1 0-3 0, 1 0-3 0-7
CV/YC 3 5
CV/YC 3 5
RF 3 5
RF 3 5
-- 27 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 1 Item Name YLEV CLEV
Range 0-62 0-63 0-15 0-15 0-15 0-3 0-15 0-3 0-3 0-3 0-3 0, 1 0, 1 0, 1 0, 1 0-3 0-3 0, 1 0, 1 0-15 0-63 0-63 0-63 0-63 0-3 0-3 480i 34 40 RF 9 2 11 0 RF 6 0 3 3 0 RF 1 0 1 RF 1 3 0 RF 0 0 RF 7 RF 34 32 32 32 Single 0 0 BLK(0) 1 2 CV/YC 7 V5/V6 36 38 CV/YC 0 3 0 CV/YC 1 CV/YC 0 Others 20 17 CV/YC 9 2 5 0 CV 8 0 3
Initial Data
2 3 4 5
SCON SCOL SHUE YDLY
6 7 8 9 10
SHAP SHF0 PREO BPF0 BPFQ
V5 4 3 3
YC 8 0 3
11 12 13
BPSW TRAP LPF
2103_1
14 15 16
AFCG CDMD SSMD
Others 0 3 0 V5/V6 1 DVI 0
17 18
HMSK HALI
19
PPHA
V5/V6 7
DVI 0
20 21 22 23
CBO1 CRO1 CBO2 CRO2
24 25
ATPD DCTR
BLK(1) 1 1
BLK(2) 2 3
BLK(3) 1 2
-- 28 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 1 Item Name YLEV CLEV
Range 0-63 0-63
Initial Data VDO DRC 41 35 31 42 RF 9 2 11 0 6 0 3 3 0 RF 1 0 DRC 1 RF 1 3 0 0 0 RF 7 34 32 CV/YC 7 VDO 0 CV/YC 0 3 0 1 CV/YC 0 CV/YC 9 2 5 0 8 0 3
2 3 4 5 6 7 8 9 10
SCON SCOL SHUE YDLY SHAP SHF0 PREO BPF0 BPFQ
0-15 0-15 0-15 0-3 0-15 0-3 0-3 0-3 0-3
11 2103_2 12
BPSW TRAP
0, 1 0, 1
13
LPF
0, 1
14 15 16 17 18
AFCG CDMD SSMD HMSK HALI
0, 1 0-3 0-3 0, 1 0, 1
19 20 21
PPHA CBO1 CRO1
0-15 0-63 0-63
-- 29 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range CV/YC 1 0 480i 0 VDO 0 MS 0
Initial Data PT 0
0 1
YOSW TCOF
0, 1 0, 1
2 3 4 5 6 7 8 9 10 11
YOF CBOF CROF SBRT RDRV GDRV BDRV RCUT GCUT BCUT
0-15 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63
DRC CV/YC 0 31 31 31 45 35 34 41 35 18 WARM 1 7 31 34 45 31 37 63 1
DRC 480i 15 31 31
V5/V6 480p 7 31 31
V5/V6 720p 7 31 31
V5/V6 1080i 7 31 31
DVI 480p VGA 7 31 31
DVI 720p 1080i 7 31 31
PT 1080i 7 31 31
MS 7 31 31
2170P_1
COOL 7 31 31 34 31 31 34
12 13 14 15 16 17 18 19 20
WBSW SBOF RDOF GDOF BDOF RCOF GCOF BCOF DCOL
0, 1 0-15 0-63 0-63 0-63 0-63 0-63 0-63 0-3
-- 30 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 1 2 3 4 5 6 Item Name PICO RGBS BLKB RGBL YLMT AGNG AKBO
Range 0, 1 0-7 0-3 0-3 0-3 0-3 0, 1 0-3 0, 1 0, 1 0-7 0, 1 0, 1
Initial Data 1 7 3 2 3 0 0 Other 3 0 0 3 0 0 PT 3 0 0 3 0
2170P_2 7 8 9 10 11 12 CLPP CLPG CLPS PPAD SYNP HVBT
-- 31 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range RF 1 1 3 1 5 2 1 0 0 2 1 0 1 2 0 7 RF 1 1 3 1 5 0 1 3 0 2 1 0 2 2 0 5
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2170P_3
SYSM VMLV VMCR VMLM VMF0 VMDL SHOF SHF0 PROV F1LV LTLV LTMD CTLV UBOF UCOF UHOF MIDE
0-3 0-15 0-3 0-3 0-3 0-15 0-3 0, 1 0-3 0-3 0-3 0, 1 0-3 0-7 0-7 0-3 0-63
Initial Data Comp Comp Comp Comp DVI DVI DVI DVI DVI MS MS CV/YC 480i 480p 1080i 720p 480i 480p VGA 1080i 720p Menu Single Twin 1 1 1 3 3 1 1 1 3 3 3 3 2 0 3 1 5 2 1 3 0 3 1 0 1 2 0 11 CV/YC 1 0 3 1 5 3 1 3 0 2 1 0 2 1 0 10 0 3 1 5 2 1 3 0 3 1 0 1 2 0 15 0 3 1 5 1 1 1 0 3 0 0 1 2 0 19 0 3 0 10 3 1 3 0 3 0 3 1 2 0 23 0 3 0 10 3 1 3 0 3 0 3 1 2 0 27 0 3 1 5 2 1 3 0 3 1 0 1 2 0 31 0 3 1 5 1 1 1 0 3 0 0 1 2 0 35 0 3 1 5 1 1 1 0 2 1 0 0 0 0 44 0 3 0 10 3 1 3 0 3 0 3 1 2 0 39 0 3 0 10 3 1 3 0 3 0 3 1 2 0 43 0 3 0 10 3 1 3 0 3 0 3 1 2 0 48 0 3 0 10 3 1 3 0 3 0 3 1 2 0 52 3 3 0 5 1 1 2 0 3 1 0 1 2 0 56
ViVid Mode
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SYSM VMLV VMCR VMLM VMF0 VMDL SHOF SHF0 PROV F1LV LTLV LTMD CTLV UBOF UCOF UHOF MIDE
0-3 0-15 0-3 0-3 0-3 0-15 0-3 0, 1 0-3 0-3 0-3 0, 1 0-3 0-7 0-7 0-3 0-63
Comp Comp Comp Comp DVI DVI DVI DVI DVI MS MS 480i 480p 1080i 720p 480i 480p VGA 1080i 720p Menu Single Twin 1 1 3 3 1 1 1 3 3 3 3 2 0 3 1 5 3 1 3 0 2 1 0 2 2 0 14 0 3 1 5 1 1 1 0 3 0 0 0 2 0 18 0 3 0 10 3 1 3 0 3 1 3 2 1 0 22 0 3 0 10 3 1 3 0 3 1 3 2 2 0 26 0 3 1 5 3 1 3 0 2 1 0 2 2 0 30 0 3 1 5 1 1 1 0 3 0 0 0 2 0 34 0 3 1 5 1 1 1 0 2 1 0 0 0 0 44 0 3 0 10 3 1 3 0 3 1 3 2 1 0 38 0 3 0 10 3 1 3 0 3 1 3 2 2 0 42 0 3 0 10 3 1 3 0 3 1 3 2 1 0 47 0 3 0 10 3 1 3 0 3 1 3 2 1 0 51 3 3 0 5 1 1 2 0 3 1 0 1 0 0 55
Standard Mode
-- 32 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range RF 1 1 3 1 5 1 1 0 0 1 1 0 0 0 0 3 RF 1 1 3 1 5 1 1 0 0 0 1 0 2 0 0 0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2170P_3
SYSM VMLV VMCR VMLM VMF0 VMDL SHOF SHF0 PROV F1LV LTLV LTMD CTLV UBOF UCOF UHOF MIDE
0-3 0-15 0-3 0-3 0-3 0-15 0-3 0, 1 0-3 0-3 0-3 0, 1 0-3 0-7 0-7 0-3 0-63
Initial Data Comp Comp Comp Comp DVI DVI DVI DVI DVI MS MS CV/YC 480i 480p 1080i 720p 480i 480p VGA 1080i 720p Menu Single Twin 1 1 1 3 3 1 1 1 3 3 3 3 2 0 3 1 5 1 1 3 0 1 1 0 2 0 0 9 CV/YC 1 0 3 1 5 2 1 2 0 0 1 0 2 0 0 8 0 3 1 5 0 1 3 0 1 1 0 0 0 0 13 0 3 1 5 1 1 1 0 2 1 0 0 0 0 17 0 3 0 10 1 1 3 0 2 1 2 0 0 0 21 0 3 0 10 1 1 3 0 2 1 2 0 0 0 25 0 3 1 5 0 1 3 0 1 1 0 0 0 0 29 0 3 1 5 1 1 1 0 2 1 0 0 0 0 33 0 3 1 5 1 1 1 0 2 1 0 0 0 0 44 0 3 0 10 1 1 3 0 2 1 2 0 0 0 37 0 3 0 10 1 1 3 0 2 1 2 0 0 0 41 0 3 0 10 1 1 3 0 2 1 2 0 0 0 46 0 3 0 10 1 1 3 0 2 1 2 0 0 0 50 3 3 0 5 1 1 2 0 1 1 0 0 0 0 54
Movie Mode
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SYSM VMLV VMCR VMLM VMF0 VMDL SHOF SHF0 PROV F1LV LTLV LTMD CTLV UBOF UCOF UHOF MIDE
0-3 0-15 0-3 0-3 0-3 0-15 0-3 0, 1 0-3 0-3 0-3 0, 1 0-3 0-7 0-7 0-3 0-63
Comp Comp Comp Comp DVI DVI DVI DVI DVI MS MS 480i 480p 1080i 720p 480i 480p VGA 1080i 720p Menu Single Twin 2 1 3 3 2 1 1 3 3 3 3 2 0 3 0 5 0 1 3 0 0 1 0 2 0 0 12 0 3 0 5 0 1 1 0 0 1 0 1 0 0 16 0 3 0 10 2 1 3 0 0 1 0 1 0 0 20 0 3 0 10 2 1 3 0 0 1 0 1 0 0 24 0 3 0 5 0 1 3 0 0 1 0 2 0 0 28 0 3 0 5 0 1 1 0 0 1 0 1 0 0 32 0 3 1 5 1 1 1 0 2 1 0 0 0 0 44 0 3 0 10 2 1 3 0 0 1 0 1 0 0 36 0 3 0 10 2 1 3 0 0 1 0 1 0 0 40 0 3 0 10 2 1 3 0 0 1 0 1 0 0 45 0 3 0 10 2 1 3 0 0 1 0 1 0 0 49 3 3 0 5 2 1 2 0 0 1 0 2 0 0 53
Pro Mode
-- 33 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 17 18 19 20 2170P_3 21 22 23 24 25 VGAP VGAS VGAB VGAC VGAV Item Name VM VMH VMM VML
Range 0-3 0-15 0-15 0-15 0-15 0-15 0-15 0-15 0-15 Vivid Standard Movie 3 3 1 15 15 12 10 10 8 6 6 4 5 0 0 0 5 Pro 0 12 8 4
Initial Data
-- 34 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range 0, 1 MS 0 DRC 7 31 31 7 7 7 Vivid 63 31 35 31 24 2 8 9 9 6 RF 2 1 0 0 GAMM (1) 8 4 4 4 CV/YC 2 1 0 0 GAMM (2) 8 8 8 8 Comp 480i 2 1 0 0 GAMM (3) 8 12 12 12 Standard 48 31 31 31 29 1 Movie 39 31 31 31 31 0 Pro 31 31 31 31 31 1 Other 1 VDO (V5/V6) 7 31 31 VDO (DVI) 7 31 31 MS 0 31 31
Initial Data
0
YCON
1 2 3 4 5 6
SPIC SCOL SHUE SPIO SCLO SHUO
0-15 0-63 0-63 0-15 0-15 0-15 0-63 0-63 0-63 0-63 0-63 0-3 0-15 0-15 0-15 0-15
PT 7 31 31
2170P_4
7 8 9 10 11 12 13 14 15 16
UPIC UBRT UCOL UHUE USHP UTMP RYR RYB GYR GYB
17
GAMM
0-3
Vivid Standard Movie Pro GAMM (0) 0 0 0 0
Comp Comp Comp DVI DVI DVI DVI DVI MS MS 480p 1080i 720p 480i 480p VGA 1080i 720p Menu Single Twin 3 3 3 2 3 0 3 3 3 3 3 1 1 1 1 1 0 1 1 1 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
18 19 20 21
GAMS GAMR GAMG GAMB
0-15 0-15 0-15 0-15
-- 35 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range RF 3 2 0 0 BLK (1) 3 0 7 1 CV/YC 3 2 0 0 BLK (2) 7 1 7 0 Comp 480i 3 2 1 0 BLK (3) 12 2 7 1
22
BLK
0-3
Vivid Standard Movie Pro BLK (0) 0 0 7 0 0 BLK (0) 0 Others 0 13 BLK (0) 1 3
Initial Data Comp Comp Comp DVI DVI DVI DVI DVI MS MS 480p 1080i 720p 480i 480p VGA 1080i 720p Menu Single Twin 3 3 3 3 3 0 3 3 3 3 3 2 2 2 2 2 0 2 2 2 2 2 0 1 0 1 0 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0
23 24 25
DCTR APED DSBO
0-15 0-3 0-15
2170P_4
26
IDSW
0-7
27
ABLM
0-3
BLK (1) 1 Small Pic 0
BLK (2) 0
BLK (3) 1
28 29
ABLT SPOF
0-15 0-31
30 31
DPSQ LRGB
0, 1 0-15
BLK (1) 1
BLK (2) 1
BLK (3) 1
-- 36 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 1 Item Name VPOS VSIZ
Range 0-63 0-63 0-63 0-15 0-15 0-63
Initial Data 25 27 1080iFULL 0 WideZoom 8 10 15 1080Vcomp 480Vcomp 15 0 31 15 0 WideZoom 1 WideZoom 1 24 31 WideZoom 4 4 Zoom 1 Zoom 1 47 31 Others 0 0 Others 0 480FULL 1 47 31 1080FULL 0 47 31 1080Vcomp 0 47 31 480Vcomp 1 47 31 Others 13 Others 0 Others 7 9
2
VSZO
3 4 5
VLIN VSCO VCEN
6 2170D_1 7 8 9 10
VPIN MVPN NSCO HTPZ MHTZ
0-63 0-3 0-63 0-31 0-3 0, 1 0, 1 0-63 0-63 0-15 0-15
11
ZOOM
12 13 14
APSW ASPT SCRL
15 16
UVLN LVLN
-- 37 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 Item Name HCNT
Range 0-63 29 1080FULL 1080Vcomp 34 WideZoom 49 10 10 40 WideZoom 7 WideZoom 31 31 1 1 2 2 0 WideZoom 20 34 33 25 32 Others 23 Others 34 Others 34 1 8 21 Zoom 7 Others 38 38
Initial Data
1
HPOS
0-63 0-63 0-15 0-15 0-63
2 3 4 5
HSIZ SLIN MPIN PIN
6 2170D_2 7 8 9 10 11 12 13
PINO
0-15 0-63 0-63 0-3 0-3 0-3 0-3 0, 1 0-63 0-63 0-63 0-63 0-63
480FULL 7
1080FULL 7
1080Vcomp 480Vcomp 7
UCP LCP UXCG LXCG UXCP LXCP XCPP
14 15 16 17 18
PPHA VANG LANG VBOW LBOW
-- 38 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 Item Name HBLK
Range 0, 1
Initial Data 1 1080FULL 1080Vcomp 50 31 WideZoom 0 WideZoom 7 7 1080FULL 1080Vcomp 2 1080Vcomp 480Vcomp 1 WideZoom 1 1080Vcomp 1080FULL 0 WideZoom 15 Others 51 27 Zoom 0 Zoom 7 7 Others 3 Others 0 Zoom 1 Others 0 Zoom 15 480FULL 1080FULL 480Vcomp 1080Vcomp 22 16 480Vcomp 1080Vcomp 480FULL 1080FULL 0 1 480FULL 480Vcomp 1080FULL 1080Vcomp 1 1 480FULL 4 8 1080FULL 1080Vcomp 480Vcomp 4 10 8 6 14 13
1 2
LBLK RBLK
0-63 0-63
3
VBLK
0, 1 0-15 0-15
4 5
TBLK BBLK
2170D_3
6
AFCM
0-3
7
JUMP
0, 1
8
VDJP
0, 1
9
VDST
0, 1
10
AKBT
0-31
-- 39 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range
Initial Data 1080Vcomp 480Vcomp 25 40 7 17 47 7 0 37 37 0 1 1 0 0 80 25 0 0 0 0 0
2170D_4
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 10
QPAM QPAV QPAP QPDC QPDV QPDP CPY1 DF DQP DHMT VFRQ VON EWDC MS15 HFRQ HFRX VMPS INTR VLNL VLNH AGCS
0-63 0-63 0-15 0-63 0-63 0-15 0, 1 0-63 0-63 0, 1 0-3 0, 1 0, 1 0, 1 0-255 0-63 0, 1 0, 1 0-3 0-255 0, 1
Others 25 40 7 17 47 7
2170D_5
-- 40 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range 1080Vcomp 480Vcomp 26 31 47 62 63 12 63 25 63 35 2 12 29 0
Initial Data
D_CONV
0 1 2 3 4 5 6 7 8 9 10 11 12 13 0
YBWU YBWL RSAP RUBW RUMB RLBW RLMB LSAP LUBW LUMB LLBW LLMB CADJ CPY2 MTRX
0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0-63 0, 1 0-3 0-3 0-3 0-15 0-15 0-15 0-3 0, 1 0-3 0, 1 0, 1 0, 1
Others 26 31 47 62 63 12 63 25 63 35 2 12
1
GAIN
PT 7 V5/V6 0 PT 7 8 8 0 1 1 V5/V6 0
Others 7 DVI 0 Others 7 8 8 Others 0
2
FIXS
CXA2151
3 4 5 6 7 8 9 10
CBGN CRGN YGN VTC HTC HWID HSEP HMSK
11
FRGB
DVI 0
Others 0
-- 41 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 1 2 3 4 5 Item Name DHPH DVPH DHAR DVAR DHPW DVPW
Range 0-255 0-63 0-255 0-255 0-63 0-7 111 20 240 135 55 5 Single
Initial Data
Twin Others 0 table-1 4 2 table-2 2
Freeze 2 table-3 1
Favorite 2
Index 2
6
DYCD
0-63
480i 3 table-0 7
7
DYSD
0-7
MID1
8
MDHP
0-255
Single VGA Others Normal Others Normal Others 72 0 Single VGA 66 Favorite VGA 34
Favorite VGA 40 Index VGA 86 Favorite VGA 155 Index VGA 77
Index VGA 38
9
MDVP
0-255
480i/480p 30
Others 0
10
MDHS
0-255
Single Others VGA Normal Others Normal Others 204 240 Single VGA 102 Favorite 31 30 Favorite VGA 103
Index VGA 116
11
MDVS
0-255
480i/480p 120 Twin/Freeze 36 8
Others 135 Index 31 41
12 13
MLHP MLVP
0-255 0-255
-- 42 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 14 15 16 17 18 19 20 21 Item Name SDHP SDVP SDHS SDVS PDHP PDVP PDHS PDVS
Range 0-255 0-255 0-255 0-255 0-255 0-255 0-255 0-255 1080i Single 0 6 Single Others 1 Others 0 Favorite 167 5 115 79
Initial Data
MID1
22 23
DPSW MDLO
0, 1 0-63
Normal
24 25 BCOL DYSS
0-15 0-3 1 Index 32 16
MS 0
Others 1
26 27
OSDH OSDV
0-63 0-63
-- 43 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range
Initial Data 480i Normal YC Others 120 180 37 120 YC 148 164 57 110 Normal Others 117 180 37 120
0 1 2 3
DRHP DRHS DRVP DRVS
0-255 0-255 0-63 0-255
Single
0 1 2 3
DRHP DRHS DRVP DRVS
0-255 0-255 0-63 0-255
Twin-Left
480i 146 164 57 110 YC 153 164 57 110 480i 153 162 57 110 480i Full 140 165 37 120 YC 153 171 28 118
MID2
0 1 2 3
DRHP DRHS DRVP DRVS
0-255 0-255 0-63 0-255
Twin-Right
0 1 2 3
DRHP DRHS DRVP DRVS
0-255 0-255 0-63 0-255
Freeze
YC 153 162 57 110 YC Vcomp 140 165 57 110 Full 140 165 37 120 Vcomp 140 165 57 110
0 1 2 3
DRHP DRHS DRVP DRVS
0-255 0-255 0-63 0-255
0 1 2 3
DRHP DRHS DRVP DRVS
0-255 0-255 0-63 0-255
Favorite-Sub
Favorite-Main
-- 44 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range Full
Initial Data 480i Vcomp
YC Full Vcomp
MID2
0 1 2 3
DRHP DRHS DRVP DRVS
0-255 0-255 0-63 0-255 0-255 0-255 0-63 0-255
Index-Main
YC
0 1 2 3 DRHP DRHS DRVP DRVS
Index-Sub
-- 45 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range 1080i 720p
Initial Data 480p 480i VGA Normal Others Normal Others Normal Others 106 208 119 167 213 159 37 17 34 120 60 120 480p 134 152 57 110 480i 208 213 27 55 VGA 148 145 45 110
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
Single
74 161 19 135
94 108 24 180
MID3
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
1080i 720p 95 111 Twin-Left 149 99 43 54 123 165 YC 200 Twin-Right 213 27 55 1080i 720p 102 114 147 98 43 54 123 165
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
Freeze
480p 139 150 57 110
480i 208 213 27 55
VGA 148 144 45 110
-- 46 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. Item Name
Range 1080i FULL Vcomp 94 94 149 149 43 43 123 123 YC 205 223 13 59 1080i FULL Vcomp 720p 720p 105 100 55 165 Favorite-Main
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
Initial Data 480i VGA 480p FULL Vcomp FULL Vcomp FULL Vcomp 128 128 208 208 118 137 153 153 213 213 159 159 37 57 17 27 34 34 120 110 60 55 120 120
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
Favorite-Sub
MID3
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
Index-Main
480p 480i VGA FULL Vcomp FULL Vcomp FULL Vcomp
0 1 2 3
VDHP VDHS VDVE VDVS
0-255 0-255 0-63 0-255
4 5 6 7 8 9 10 11
VDVO VCPO VCWD VYCD VSTP VSTT VHSC VFRV
0-3 0-255 0-7 0-63 0-255 0-15 0-255 0, 1
YC 0 95 3 0 62 0 130 0
Index-Sub
YC
480i 1080i 0 0 90 40 3 3 0 0 62 144 0 0 130 130 0 0
720p 0 40 3 0 132 0 130 0
480p 0 70 3 0 110 0 130 0
VGA 0 70 3 0 119 0 130 0
-- 47 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Item Name POP MHLY MHLC MVLY MVLC MHYR MHYL MHYE MHYO MHCR MHCL MHCE MHCO MVYR MVYL MVYE MVCR MVCL MVCE POP MHLY MHLC MVLY MVLC MHYR MHYL MHYE MHYO MHCR MHCL MHCE MHCO MVYR MVYL MVYE MVCR MVCL MVCE
Range 0-63 0-3 0-3 0-3 0-3 0-3 0-3 0-7 0, 1 0-3 0-3 0-7 0-1 0-3 0-3 0-7 0-3 0-3 0-7 0-63 0-3 0-3 0-3 0-3 0-3 0-3 0-7 0, 1 0-3 0-3 0-7 0-1 0-3 0-3 0-7 0-3 0-3 0-7 0 1 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 16 1 3 0 0 1 1 4 1 0 0 0 0 0 0 0 0 0 0 1 1 3 0 0 1 1 2 1 0 0 0 0 0 0 0 0 0 0 17 1 3 0 0 1 1 2 1 0 0 0 0 0 1 1 0 0 0 2 1 3 0 0 1 1 2 1 0 0 0 0 0 0 0 0 0 0 18 1 3 0 0 1 1 2 1 0 0 0 0 1 1 3 0 0 0
Initial Data 3 1 3 0 0 1 1 5 1 0 0 0 0 0 0 0 0 0 0 19 1 3 0 0 0 1 3 0 0 0 0 0 1 1 1 0 0 0 4 1 3 0 0 2 1 6 1 0 0 0 0 1 1 1 0 0 0 20 0 0 0 0 0 1 2 0 0 0 0 0 0 0 0 0 0 0 5 1 3 0 0 3 2 7 1 0 0 0 0 2 1 3 0 0 0 6 1 3 0 0 3 2 7 1 0 0 0 0 2 1 3 0 0 0 7 1 3 0 0 3 2 7 1 0 0 0 0 2 1 3 0 0 0 8 1 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 9 1 3 0 0 0 1 2 1 0 0 0 0 1 1 3 0 0 0 10 1 3 0 0 2 2 4 1 0 0 0 0 1 1 3 0 0 0 11 1 3 0 0 1 1 7 1 0 0 0 0 1 1 3 0 0 0 12 1 3 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 13 1 3 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 14 1 3 0 0 1 2 2 1 0 0 0 0 1 1 3 0 0 0 15 1 3 0 0 1 2 7 1 0 0 0 0 2 1 5 0 0 0
MID5
21 22 23 24 25 26 27 28 29 30 31 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 3 3 3 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 2 2 4 5 7 2 4 7 7 0 0 2 7 0 0 0 0 0 0 0 1 1 1 1 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 4 4 0 0 4 4 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 1 2 0 1 1 0 0 1 1 0 0 1 1 0 4 4 0 0 4 4 0 0 3 5 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 4 4 0 0 4 4 0 0 0 0
-- 48 --
KV-32HS500/32HV600/34DRC500/34XBR800/ 36HS500/ 36XBR800/38DRC500/40XBR800/42DRC800
KV-32HS500 SERVICE DATA LISTS
Category Name No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Item Name POP MHLY MHLC MVLY MVLC MHYR MHYL MHYE MHYO MHCR MHCL MHCE MHCO MVYR MVYL MVYE MVCR MVCL MVCE POP MHLY MHLC MVLY MVLC MHYR MHYL MHYE MHYO MHCR MHCL MHCE MHCO MVYR MVYL MVYE MVCR MVCL MVCE
Range 0-63 0-3 0-3 0-3