Text preview for : BFT080F-TE.pdf part of MAKITA BFT080F-TE MAKITA BFT080F-TE.pdf
Back to : BFT080F-TE.pdf | Home
T ECHNICAL INFORMATION
Models No.
BFT040F, BFT080F, BFT122F,
BFT123F BFT040F, BFT080F,
PRODUCT
P 1 / 21
L
Description Cordless Screwdrivers 9.6V BFT122F
12V
CONCEPTION AND MAIN APPLICATIONS
Specially developed for fastening works in assembling line.
Their common feature and benefits are as follows. L
* New charging system
* Higher accuracy in fastening torque H
* Superior handling
BHT123F (12V) is applicable to tightening at
high turning angle. W
And their fastening torque range is as listed below.
Torque range in Identification Voltage BFT123F H
Model No. hard joint : (N.m) plate (V)
BFT040F 1-4 Yellow
BFT080F 3-8 Blue W
9.6
BFT122F 5 - 12
Red
BFT123F 5 - 12 12
Dimensions : mm ( " )
Model No. BFT040F, BFT080F, BFT122F BFT123F
Length ( L ) 200 (7-7/8)
Width ( W ) 65 (2-9/16) 71 (2-13/16)
Height w/2.0Ah battery 251 (9-7/8) 260 (10-1/4)
Specification (H) w/3.3Ah battery 274 (10-3/4) 283 (11-1/8)
Model No.
Specifications BFT040F BFT080F BFT122F BFT123F
Type of cell Ni-MH Ni-MH
Battery Voltage : V 9.6 12
Capacity : Ah 2.0 / 3.3 2.0 / 3.3
Energy : Wh 19.2 / 31.7 24.0 / 39.6
Torque range Hard joint 1 - 4 (8.85 - 35.4) 3 - 8 (26.6 - 70.8) 5 - 12 (44.3 - 106) 5 - 12 (44.3 - 106)
: N.m (in.lbs) Soft joint 1 - 3.5 (8.85 - 31.0) 3 - 6.5 (26.6 - 57.5) 5 - 10 (44.3 - 88.5) 5 - 12 (44.3 - 106)
No load speed : rpm.= min-1 950 540 320 390
Driving shank : mm ( " ) Hex 6.35 (1/4) Hex 6.35 (1/4)
Soft start Yes Yes
LED Job Light Yes Yes
Externally accessible brush Yes Yes
Net weight w/ 2.0Ah battery 1.3 (2.9) 1.6 (3.5)
: kg(lbs) w/ 3.3Ah battery 1.5 (3.3) 1.8 (4.0)
Standard equipment
* Adjust grip for torque adjusting ......... 1 pc. (exclusively for Italy, USA, Canada)
* Protector ............................................. 1 pc. (exclusively for Germany)
< Note > The standard equipment for the tool shown may differ from country to country.
Optional accessories
For BFT040F, BFT080F and BFT122F For BFT123F * Charger DC14SA
* Battery BH9020 * Battery BH1220 * Charger DC24SA
* Battery BH9020A * Battery BH1233 * Auto refresh adapter ADP03
* Battery BH9033 * Grip base set * Protectors ( red, blue, yellow and clear )
* Battery BH9033A * Grip 37 * Adjust grip for torque adjusting
Features and benefits
Lighter than Competitor A 12V series models
P 2 / 21
by approx. 90g.
*Higher Torque Accuracy
Light Tool Weight
Adjust grip (optional accessory) Lighter than BOSCH 12V series models
by approx. 90g.
Without this adjust grip,
The measured weight of BFT123F : 1.64 Kg
it is impossible to adjust the
The measured weight of Model A-J : 1.73 Kg
fastening torque for these models.
See the comparison in page 6
9 1
1 9
2 8
2
8 3
7 5 7
3 BFT123F
5
4
BFT040F 4
BFT080F 6A
BFT122F
6
Protector (optional accessory)
Light Tool Weight By mounting this protector to these
4 models, the materials
Lighter than 6796FD series models by approx. 70g.
(such as automobile's body on the
See the comparison in page 6.
assembling line) can be protected
from the scratch, etc.
For Model BFT123F
Side grip for the fastening at high turning angle
1. Bit sleeve, coated with rubber for protection 7. D28 type motor with the following features.
the materials from scratch, etc. * Externally accessible brushes.
2. LED Job Light * Replaceable armature
3. ON-OFF switch with the following features. * Uses compact and light, yet
* Delayed re-starter for powerful rare earth magnet
reducing deviation by 8. Indication lamp and beeper inform
unintentional over tightening. operator of the following matters
* Starts 0.2 sec. after pulling * Sufficient fastening : Green on
switch trigger. * Insufficient fastening : Red on
* Soft start for suppressing the and beeping
starting shock. * Warning that remaining battery
4. Anti-slip dimpled grip power is little. : Red on and beeping
5. Conveniently located push button type reverse switch * Too little battery power to rotate
the machine. : Motor stops with
6. Operated with the batteries of Red on and beeping
new charging system. See the further information in the
page 3.
6A. High turning angle in soft joint,
with Battery BH1233 12V, 3.3Ah of 9. Identification plate
new charging system. See the further information in the
page 4.
Features and benefits P 3 / 21
Indication lamp, buzzer and auto stop system
In case of no trouble on the result of work and on the machine itself, the lamp and beeper inform
of the following matters.
Lamp Beeper Auto stop What the lamp, beeper and auto stop system inform of.
Lights up in the A series of Under testing the function of indication
order of green, short beeps lamp and beeper, when installing battery.
red and white.
Finish of single fastening process with reaching
the pre-set fastening torque.
Lights up At this time, clutch works and delayed restarter
No beep ON
in green. keeps the motor still for one second after finishing
sufficient fastening process, to avoid the unintentional
over-tightening which will occur by mis-operation
of switch trigger.
In case of trouble on the result of work, or on the machine itself, the lamp and buzzer inform of the following matters.
What the lamp, beeper and
Lamp Beeper Auto stop auto stop system inform of. Action to be taken
Insufficiently finished single Try again to fasten the screw
fastening process, without or bolt.
Lights up A long
reaching the pre-set fastening It is important to pull the switch
in red. beep
torque. trigger on, until clutch works.
Remaining battery Motor rotates on, however, it is
A series power is little. recommended to replace with
Flickers in red of long the fully charged battery in the
slowly. beeps appropriate time.
Impossible to fasten screws Immediately replace the
A series
or bolts with the pre-set old battery with the fully
Lights up of long ON
fastening torque any more. charged battery.
in red. beeps
Lights up in A series Warning of abnormal drop of Motor does not rotate in spite of
red and green of long battery voltage for some pulling switch trigger.
ON
alternately. beeps reason. The warning by lamp and beeper
stops with removing battery.
A series Warning of over heat on Remove the battery immediately
Flickers controller. and cool the machine down.
of long ON
in red
beeps
quickly.
Lights up in A series The battery has been installed Release the switch trigger.
red and green of long with keeping switch trigger
alternately. beeps ON pulled.
Features and benefits P 4 / 21
Identification Plate for BFT040F Series Models
BFT040F Series Models (BFT040F, BFT080F, BFT122F and BFT123F) are equipped with
Identification Plates for easy control in your factory.
Even if the name plates would fall off the machines, or even if it is too difficult to read the indications from the worn
name plates, BFT080F Series Models can be easily identified from the identification plates.
***** Identification number with 5 digits;
Identification plate
With this 5 digits, it can be
5 - 12N.m identified, (for example) in which
manufacturing section the relative
machine is employed.
The identification number is put
by MAKITA, independent of the
Torque range; serial numbers.
Model No. can be identified with
this indication as mentioned below.
***** ***** *****
1 - 4N.m 3 - 8N.m 5 - 12N.m
BFT040F BFT080F BFT122F
Yellow plate Blue plate BFT123F Red plate
How to control the BFT040F series models with the identification plate
BFL080F series models are employed in some factory, for example , as listed below.
Employed Indications on the identification plate Employed
Manufacturing model Torque range Identification No. quantity
section A BFT040F 1 - 4N.m 00001 - 00250 250
BFT080F 3 - 8N.m 00123 - 00275 153
Employed Indications on the identification plate Employed
Manufacturing model Torque range Identification No. quantity
section B BFT040F 1 - 4N.m 00251 - 00300 50
BFT122F 5 - 12N.m 10300 - 10449, 00899, 15689, 152
Employed Indications on the identification plate Employed
Manufacturing model Torque range Identification No. quantity
section C BFT123F 5 - 12N.m 00030 - 00119, 00830 - 00836, 97
BFT080F 3 - 8N.m 50025 - 50099, 00830 - 00836, 15689, 83
You can identify the model No. and to which manufacturing section the relative machine belongs, from the
indications on the plates.
00237 00899 00117
1 - 4N.m 5 - 12N.m 5 - 12N.m
BFT040F employed in BFL122F employed in BFL123F employed in
manufacturing section A manufacturing section B manufacturing section C
00129 00296 50057
3 - 8N.m 1 - 4N.m 3 - 8N.m
BFL080F employed in BFT040F employed in BFT080F employed in
manufacturing section A manufacturing section B manufacturing section C
Features and benefits P 5 / 21
Limit Capacity Table
[BFT040F] with 9.6V 2.0 Ah battery
Turning angle (