Text preview for : ML122-TE.pdf part of MAKITA ML122-TE MAKITA ML122-TE.pdf
Back to : ML122-TE.pdf | Home
T ECHNICAL INFORMATION
Models No. ML122
PRODUCT
P1/5
Description Rechargeable Job Site Light
CONCEPTION AND MAIN APPLICATIONS L
This product has been developed for workshop,
automotive service center where the pinpoint irradiation
is often required, when repairing of narrow and complex H
section, for example, engine room of automobile, etc.
Its brief benefits and features are,
* Both 9.6V and 12V batteries can be attached to this W
product.
* The continuous illumination time is 230 minutes (almost Dimensions : mm ( " )
4 hours), if the full charged Ni-MH battery 1235, 12V / 3.0Ah is Length ( L ) w/o battery 347 (13-5/8)
attached to this product. Height ( H ) 94 (3-11/16)
Width ( W ) 97 (3-13/16)
Specification
Battery voltage ( V ) 12 9.6
Battery capacity (Ah) 3.0 2.0 1.3 3.0 2.0 1.3
*Continuous illumination time: approx.min. 230 150 90 230 150 80
**Illumination (lx) 380 330
Net weight w/o battery :Kg (lbs ) 0.35 (0.77)
< Note > * Continuous illumination time: The figures shown in the above list can differ from condition to condition
of batteries or room temperature.
**Illumination (lx) : The figures shown in the above list were measured on the following conditions.
* With attaching reflector to the product
* Measured at the point of 50 cm distant from light source
Standard equipment
* Set plate for the batteries without push button ............................. 1 pc.
* Strap ............................................................................................. 1 pc.
* Hook ............................................................................................. 1 pc.
* Reflector set.................................................................................. 1 pc.
< Note > The standard equipment for the tool shown may differ from country to country.
Optional accessories
* Fluorescent tube 12 V batteries 9.6 V batteries
* Charger DC1411 * Ni-Cd battery 1222 * Ni-Cd battery 9122
* Charger DC1801 * Ni-Cd battery 1202 * Ni-Cd battery 9102
* Charger DC9700 * Ni-Cd battery 1202A * Ni-Cd battery 9102A
* Charger DC9710 * Ni-Cd battery 1200 * Ni-Cd battery 9100
* Charger DC9711 * Ni-Cd battery 1200A * Ni-Cd battery 9120
* Charger DC1290 * Ni-Cd battery 1220 * Ni-MH battery 9133
* Charger DC1470 * Ni-MH battery 1233 * Ni-MH battery 9134
* Charger DC1201 * Ni-MH battery 1234 * Ni-MH battery 9135
* Charger DC1422 * Ni-MH battery 1235 * Ni-MH battery 9135A
* Fast charger DC1439 * Ni-MH battery 1235A
* Fast charger DC1809
Features and benefits P2/5
Removable reflector set
By turning this reflector set around
the lamp, your desired position can be irradiated.
Supports for stabilizing
when it is put on something
Absorber
To protect the body
from shock
Both 12V and 9.6V battery can be
Transparent lamp cover attached.
being able to irradiate wide With set plate (standard equipment),
all of our cluster type 9.6 V and 12 V batteries
can be used.
Removable hook and strap
Comparison of products
MAKITA MAKITA
Model No.
Specifications ML122 ML701
Voltage ( V ) 9.6 / 12 7.2
*Continuous illumination 12V/ 2.0Ah 150 120
time: approx.min. 9.6V/ 2.0Ah 150 with battery 7.2V 1.3Ah
12V 380
**Illumination (lx)
9.6V 330
Type of tube Compact fluorescent tube 13W x 2 Fluorescent tube 4W x 1
Fluorescent tube Service life : h 2,600 1,000
Starter No No
Removable strap Yes Yes
Dimensions : mm ( " ) Length 347 (13-5/8) 210 (8-1/4)
w/o battery Width 97 (3-13/16) 44 (1-3/4)
Height 94 (3-11/16) 91 (3-5/8)
Net weight w/o battery :Kg (lbs ) 0.35 (0.77) 0.23 (0.51)
Weight w/ battery 1222 :Kg (lbs ) 1.0 (2.2)
Weight w/ battery 9122 :Kg (lbs ) 0.9 (1.98) 0.57 (1.26) w/ battery 7000
< Note > * Continuous illumination time: The figures shown in the above list can differ from condition to condition
of batteries or room temperature.
**Illumination (lx) : The figures shown in the above list were measured on the following conditions.
* With attaching reflector to the product
* Measured at the point of 50 cm distant from light source
Repair P3/5
< 1 > Replacing battery holder, switch and circuit complete
(1) Connecting lead wires
The lead wires have to be connected as illustrated in Fig. 1. And then, solder them.
Correct connection Wrong connection
Fig. 1 Fig. 1A
Fluorescent Battery holder
tube holder Circuit complete
(B) (C) (A)
(A) Connecting circuit complete's lead wire with battery holder
Lead wire (black) covered with
yellow tube
Yellow tube Solder here.
Lead wire (red) covered with
yellow tube
(B) (C) Connecting circuit complete's lead wire with switch
Lead wire (black) covered with
Circuit complete side
yellow tube
Yellow tube
Switch
Yellow tube
Lead wire (black) covered with
yellow tube
Repair P4/5
(D-1)Removing circuit complete's lead wire from fluorescent tube holder
Insert small screwdriver deep into rib 1 and 2 and pull out the lead wires pressing
with the screwdriver in the direction of the arrow as illustrated in Fig. 2A.
Lead wires (red) Tube installing side
Fig. 2
Fluorescent tube holder
View from tube installing side
Rib 1
Rib 2
Fluorescent tube holder
Fig. 2A
(D-2)Connecting circuit complete's lead wire with fluorescent tube holder
Insert receptacles into the holes of fluorescent tube holder with facing the receptacles' spikes to the outside
as illustrated in Fig. 3.
Fluorescent tube holder
Lead wire (black) covered
with yellow tube
The receptacles' spikes have to be
Circuit complete faced to out side.
Lead wire (red) covered
with yellow tube
Fig. 3
< Note > The spikes of pulled (used) receptacles are deformed as illustrated in Fig. 3A.
The used ones have to be corrected as illustrated in Fig. 3B.
Deformed spike Corrected spike
Fig. 3A Fig. 3B
Circuit diagram P5/5
A
Terminal +
Switch
Circuit
Battery holder Fluorescent tube
complete
Terminal B
Wiring diagram
Place lead wire, so that it can not be pinched
by housing, circuit complete and battery holder.
Battery holder
Fluorescent
tube holder Circuit complete
Place lead wire, so that it can not be pinched
by housing, circuit complete and fluorescent tube holder.