Text preview for : ALPINE INA-N333RR.rar part of ALPINE INA-N333RR ALPINE ALPINE INA-N333RR.rar
Back to : ALPINE INA-N333RR.rar | Home
SERVICE MANUAL
GPS Car Navigation / CD Receiver
- Confidential -
"Schematic Diagram (ECU P.W.Board / ASSY,FPC SHEET SW) cannot use a reference function"
TO ALPINE Home Page
10 /03-A
68E36039S01
INA-N333RR
The following cautions will prevent accidents in the workplace and will ensure safe products.
*The symbols indicate caution is needed to prevent injuries and damage to property.
The symbols and their meanings follow.
If you ignore this symbol and handle the product incorrectly or unsafely,
Warning serious injury or death may result.
If you ignore this symbol and handle the product incorrectly or unsafely,
Caution injury or only material damage may result.
*The following symbols indicate two levels of cautions.
When you see this symbol, you have to be very careful.
When you see this symbol, you have to follow the instructions there.
Warning
Do not look squarely into the laser light Fuse Caution
coming from the pickup. Always use a designated fuse.
You may loose you sight. Use of an incorrect fuse may result in a fire.
Caution
Do not allow wiring to be caught in the Battery Caution
screw/chassis. Use the designated battery.
If wiring is caught in the screw/chassis, it may Confirm the correct polarity and seat of the battery.
cause a short circuit, resulting in a fire. An incorrect battery or an improperly connected or
seated battery may result in a fire.
High Temperature Caution Designated Parts Caution
Touching the heat sink may cause severe burns. Look up the part list and ensure that only
designated parts are used to prevent problems or
accidents.
Reverse Power Supply Connections or Wiring Caution
Misconnections Caution Ensure that the wiring is correct when rewiring to
Reverse power supply connections or prevent problems with ignition/breakdown.
misconnections may cause ignition problems and
smoke may result.
Soldering Caution Wear Gloves
Hot solder from solder splash may cause severe Wear gloves to prevent electrical shocks or injury
burns. from the end face of the metal.
For the FDA laser standard, the following CAUTION label is stuck on each product.
Please be careful for repair.
CAUTION-Laser radiation when open, DO NOT STARE INTO BEAM
-2-
INA-N333RR
Contents
Packing Assembly Parts List 4
Packing Method View 4
System Connection 5 to 7
Specifications 8,9
I/O Interface 10 to 16
Extension Cable 17
Adjustment Procedures 18 , 19
Block Diagram 20, 21
Parts Layout on P.W.Boards and Wiring Diagram 22 to 26
Schematic Diagram 27 to 40
Terminal Voltage of IC/ TR 41 to 48
Description of IC Terminal 49 to 55
Exploded View (Cabinet) 56 , 57
Exploded View (DVD Deck Mechanism) (DV33M010) 58
NOTE : Due to continuing product improvement, specifications and designs are subject to
change without notice.
-3-
INA-N333RR
Packing Assembly Parts List
Symbol Part No. Description Symbol Part No. Description
No. No.
101-1 03S60820Y16 SCR,MCH 5X8 ZN A
101-2 03S60824Y01 SCR,WAV 1.7X4 ZN A
101-3 36A11113W01 CAP,RUBBER(A)
101-4 03A60836Y01 SCR,CUS 5X7 ZN A
102 01T15359Y14 ASSY,ISO CONN N033RS
103 01T85385W04 GPS ANT,GPA-CG2C1
104 15D50063Y01 CARRYING,CASE
105 15D50406W02 CASE,INNER
106 68P50520Y74 O/M AOEU
Packing Method V iew
104
101 -2
101 -1
X4 X1
101 -3
103
X1
101 -4
106 105
X1
102
101
102
AMP
0.85
0.5
AMP
0.85
0.5
X1
105
103
104
X1
X1 X3 X1
X1
TO CONTENTS
-4-
INA-N333RR
System Connection
ISO Antenna Converter Plug Antenna
ISO Antenna Plug
1 2
(Yellow/Blue) PARKING BRAKE
To the parking brake signal line
3
(Pink/Black) AUDIO INTERRUPT IN
To vehicle phone
(Blue/White) REMOTE TURN-ON
4
To amplifier or equalizer
(Orange) DIMMER To the instrument cluster
illumination lead
5
6 To power antenna
(Red) IGNITION
(Black) GND 7
Ignition Key
(Blue) POWER ANT 8
choke 10
coil 9
Battery
BATTERY (Yellow)
12 To the vehicle speed pulse line
SPEED SENSOR
(Green/White)
*
speed sensor CD Changer
auxiliary lead (Ai-NET)
To remote control (Sold Separately)
interface Box
13
To RDS-TMC Box (TMC-001P)
Speakers
15 14
19 Amplifier Front
22 23
20 Amplifier Rear
17 22
18
Ai-NET -
21 Amplifier Subwoofer
16
NORM EQ/DIV 22
(Green) 25
Rear Left
(Green/Black) 26
(White) 27
Front Left
(White/Black) 28
Speakers
(Gray/Black) 29
Front Right
(Gray) 30
(Violet/Black) 31
24
Rear Right
(Violet) 32
TO CONTENTS
-5-
INA-N333RR
1 Antenna Receptacle 13 Remote Control Interface Connector
Connect to the supplied ISO antenna converter plug. To remote control interface box.
2 Parking Brake Lead (Yellow/Blue) 14 To RDS-TMC Receiver (Optional)
Connect this lead to the power supply side of the parking
NOTE
brake switch to transmit the parking brake status signals to To connect an Alpine RDS-TMC Receiver, consult your Alpine
the INA-N333RR. dealer.
3 Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular 15 GPS Antenna (Included)
phone which provides ground shorting when a call is 16 Power Supply Connector
received. Ai-NET Connector
17
4 Remote Turn-On Lead (Blue/White) Connect this to the output or input connector of other
Connect this lead to the remote turn-on lead of your product (CD changer, Equalizer, etc .) equipped with
amplifier or signal processor. Ai- NET.
5 Dimmer Lead (Orange) 18 System Switch
This lead may be connected to the vehicle's instrument When connecting a processor using Ai-NET, place this
cluster illumination lead. This will enable the vehicle's switch in the EQ/DIV position. When no device is
dimmer control to dim the backlighting of the unit. connected, leave the switch in the NORM position.
6 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle's fuse NOTE
Be sure to turn the power of f to the unit before changing the
box or another unused power source which provides (+) 12V
switch position.
only when the ignition is turned on or in the accessory
position.
7 Ground Lead (Black) 19 Front Output RCA Connectors
Connect this lead to a good chassis ground on the vehicle. RED is right and WHITE is left.
Make sure the connection is made to bare metal and is 20 Rear Output RCA Connectors
securely fastened using the sheet metal screw provided. RED is right and WHITE is left.
-
8 Power Antenna Lead (Blue) 21 Subwoofer Output RCA Connectors
Connect this lead to the +B terminal of your power antenna, RED is right and WHITE is left.
if applicable. 22 RCA Extension Cable (Sold Separately)
NOTE 23 Ai-NET Cable (Included with CD Changer)
This lead should be used only for controlling the vehicle's power 24 ISO Connector (Speaker Output)
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
25 Left Rear (+) Speaker Output Lead (Green)
26 Left Rear (