Text preview for : old_bass.pdf part of Ashdown ABM Complete schematics for Ashdown ABM Bass Amplifier
Back to : Ashdown ABM Schematics.zi | Home
Ashdo w n Bass
Magnifiers
AB M, MAG
& Electric B lue
O perating I nstructio ns
Specificatio ns
ABM, MAG & ELECTRIC BLUE PREAMPS
INPUTS
High Input Impedance 3.9M Ohms Input range 150mV to 20V p-p
Low Input Impedance 10K Ohms Input range 300mV to 40V p-p
Stereo Line Inputs (ABM only) Impedance 22K Ohms Input level 0dBu nominal
Effects Return Impedance 22K Ohms Input level 0dBu nominal
OUTPUTS
Tuner Output Impedance 22K Ohms Level 0dBu nominal
Sub Output (ABM only) Impedance 22K Ohms Level 0dBu nominal
Effects Send Impedance 22K Ohms Level 0dBu nominal
D.I. Output 600 Ohms balanced Level -20dBu nominal
Low Pass (except Electric Blue) Impedance 1K Ohms Level switched 0/+4dBU
High Pass (except Electric Blue) Impedance 1K Ohms Level switched 0/+4dBU
Full Range (except Electric Blue) Impedance 1K Ohms Level switched 0/+4dBU
Speaker Outputs Minimum impedance 4 Ohms (Electric Blue: 8 Ohms)
EQUALISATION (Electric Blue & MAG)
Bass +/-15dB @ 100Hz
Lo Mid +/-15dB @ 340Hz
Middle +/-15dB @ 660Hz
Hi Mid +/-15dB @ 1.6kHz
Treble +/-15dB @ 7kHz shelving
Deep +8dB @ 50Hz
Bright +10dB @ 10kHz
Signal to Noise Better than 80dB (EQ flat)
Distortion Less than 0.5% THD
GENERAL SPECIFICATION
Frequency Response -3dB at 17Hz and 30KHz (Electric Blue: -3dB at 22Hz and 25KHz)
Rack Preamp RPM1 Crossover Variable between 35 and 160Hz
Power Requirements 230 / 115V
Power Output (Electric Blue only) 120 Watts RMS into the internal speaker, 240 Watts peak
Howe Farm · Southend Road · Chelmsford · Essex · CM2 7TE
E-mail: [email protected]
Ashdo w n Bass
Magnifiers
AB M, MAG
& Electric B lue
O perating I nstructio ns
Important Safety Instructions
BASIC PRECAUTIONS
WARNING - When using electrical products, basic precautions should be followed, including the following:
1. Read all the instructions before using the product.
2. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, in a wet
basement or near a swimming pool, or the like.
3. This product may cause permanent hearing loss. Do not operate for long periods of time at high
volume level or at any level that is uncomfortable. If you experience any hearing loss or ringing in the
ears, you should consult an audiologist.
4. The product should be located so that its location or position does not interfere with its proper
ventilation.
5. The product should be located away from heat sources such as radiators, heat registers, or other
products that produce heat.
6. The product should be connected to a power supply of the type described in the operating
instructions or as marked on the product.
7. The power supply cord of the product should be unplugged from the outlet when left unused for a
long period of time.
8. Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through
openings.
9. The product should be serviced by qualified personnel when:
a. The power supply cord or the plug has been damaged; or
b. Objects have fallen, or liquid has been spilled into the product: or
c. The product has been exposed to rain or moisture: or
d. The product does not appear to operate normally or exhibits a marked change in performance: or
e. The product has been dropped, or the enclosure damaged.
10. Do not attempt to service the product. All servicing should be referred to qualified service personnel.
11. For continued protection against the risk of fire, replace fuses only with those of the same type and
rating as indicated on the back of the product.
12. Please keep the fans clean failure to do so could result in overheating and shutdown of your amplifier.
WARNINGS USED ON THE EQUIPMENT
The ABM Design Philosophy
This is a NO COMPROMISE design using the best parts available wherever possible.
Some examples of this are as follows:
· Gold plated jack sockets for reliability and long life.
· Full metal XLR sockets for strength and their positive latching facility.
· Powerful output stages for extra headroom (rated in English RMS real power and not MUSIC or
PEAK power as these can claim to be 2 or 3 times the actual real power of the amplifier).
· All MOSFET output devices for reliability and superior bass power and quality.
· Doubling up of the reservoir capacitors for the output stage providing double the available `punch'
or instantaneous transient power (very important for bass).
· Doubling up of the cooling fans for reliability and reduced fan noise (2 fans can run at half the speed
to provide the same cooling capacity and as a consequence generate only half the noise of one fan
running at twice the speed).
· Speed controlled fan drive circuit. Again this reduces the amount of fan noise as the fans run slow
when the unit is cool and increase in speed with output power demands.
· Powerful TOROIDAL mains transformer. This is more expensive than a laminated stack transformer
but has better regulation, i.e., provides more power on demand without sagging out and also has a
minimal external magnetic field which means that single coil pick up basses are less likely to pick up
mains hum from the amplifier.
· FET input circuit to the preamp for `warmth' even when using the CLEAN input mix setting.
· D.C. heaters for the TUBE section for low noise operation.
· Switch on delay for silent power up.
· Thermal trip for output protection.
· Relay switched speaker output lines for silent power down.
· Sub Bass output and Sub Harmonics facility for really serious bottom end.
Everything possible has been done to make this a reliable, top of the range, minimum service, high quality,
long lasting powerful bass amplifier.
We know you will appreciate the effort that has been put into the design and manufacture of this unit
and you will be rewarded in your choice of bass amplifier by long life and reliability.
Fro nt Panel Facilities
ABM, MAG & ELECTRIC BLUE
ABM
MAG
Electric Blue
INPUTS
There are two choices of instrument input, these are marked HIGH and LOW.The HIGH input is high
sensitivity and also high impedance to suit the output from PASSIVE basses.The LOW input is low
sensitivity and lower impedance to suit the output from ACTIVE basses.
INPUT CONTROL
The INPUT control sets the signal level through the preamp in conjunction with the INPUT LEVEL VU
Meter (Electric Blue uses a LED display).This is adjusted to give a reading of 0VU on the meter (yellow
LED on Electric Blue) for average playing dynamics with occasional peaks into the red (red LED on Electric
Blue) region.
INPUT MIX CONTROL (ABM only)
This routes the signal either through a clean Solid State amplification section or through a Dual Triode
Valve / Tube amplification section to add either tonal character, i.e., warmth, or depending on how far the
control is advanced, a degree of Tube distortion. A Mix of these two amplification sections can be achieved
with this control.
N.B.The degree of tube distortion with this control turned fully clock wise will also depend on the setting
of the INPUT control.
PUSH FLAT / SHAPE (ABM only)
With this button in its OUT position a fixed E.Q. is superimposed on the preamp to give a bright but
punchy character to the sound. Pushing this button IN returns the preamp to a Flat frequency response.
This facility is also footswitchable on the ABM range via a socket on the rear panel.
DEEP (Electric Blue & MAG)
With this button IN, a fixed E.Q. is superimposed on the preamp to give a BASS boost to the sound.This
gives +8dB at 50Hz.
BRIGHT (Electric Blue & MAG)
With this button IN, a fixed E.Q. is superimposed on the preamp to give a TREBLE boost to the sound.
This gives +10dB at 10kHz.
E.Q. IN / OUT
This button switches the Equalisation section IN or OUT, i.e., the Bass, Middle and Treble controls and the
two sets of sliders (rotary controls on Electric Blue) placed between these.This facility is footswitchable on
the ABM range via a socket on the rear panel.
EQUALISATION
This consists of BASS, MIDDLE and TREBLE controls with two sliders (rotary controls on Electric Blue &
MAG) placed in between.This can be used in a number of ways:
· Firstly as a very simple Bass, Middle and Treble tone control section as found on older traditional
amplifiers.This is done by leaving the two sets of sliders (rotary controls on Electric Blue & MAG) set in
their centre positions and using only the BASS, MIDDLE and TREBLE controls to alter the overall tone.
· Secondly, if more control is required, then the sliders (rotary controls on Electric Blue & MAG) can also
be used to tailor the E.Q. in the regions between the main tone controls.
This provides a very versatile Equalisation section that is simple to understand and operate, yet provides a
wide degree of variation. It retains the simplicity of a three-control tone section but provides the flexibility
of a graphic equaliser.
SUB HARMONICS (ABM & MAG only)
This section consists of an IN / OUT switch and a LEVEL control.When switched IN, Sub Harmonics an
octave below the notes being played are produced.The level of these Sub Harmonics relative to the
straight bass sound can be adjusted using the LEVEL control.This is very effective in thickening the sound
and you will find in use that only a small degree of this lower octave is required to really fill out the sound
and provide a character to the sound that is not possible by any other means.The degree of Sub
Harmonics is also dependant on the setting of the BASS control.
DIRECT INJECT (D.I.)
A balanced D.I. is provided on the front panel XLR socket. ABMs and MAGs feature a push button placed
below the input that allows the user to choose either a Pre E.Q. / Pre Sub signal or a Post E.Q. Post Sub
and effects signal EBs feature a Post E.Q. Post effects signal.The output signal from this XLR socket is set
to a level and impedance suitable for connecting directly into the Microphone input of a mixing desk for
either Direct Injection into the PA system or for recording.
PUSH TO MUTE (ABM only)
When pushed IN this button mutes the output from the preamp to the power amp, mutes the output from
the D.I. socket and mutes the output from the Sub Out socket as well.This leaves the output from the TUNER
/ LINE socket still available to allow muted tuning. A blue LED is provided next to this switch to indicate when
the amplifier is Muted.This operates only from the front panel MUTE switch and not from the external foot
switch MUTE facility, i.e., pressing this button mutes all sound from the amplifier and allows a tuner connected
to the TUNER / LINE socket to operate for silent tuning. Release the button and you are back in action again.
A red LED lights on the front panel when the amp is muted.
TUNER / LINE OUT
This output socket provides a line level signal that can be used either for a permanent connection to a
tuner or a line output to slave up to other power amplifiers. (ABM & MAG - Please note that if this socket
is used as a slave output to other power amplifiers that the MUTE button will not mute the signal to the
external power amplifiers.)
SUB OUT (ABM only)
This output socket provides a Low Pass filtered output for connection to the ASHDOWN 400 Watt
1 x 15" powered sub unit for additional extra low bottom end.This may also be used to drive other power
amplifiers to provide additional low bottom end to the system.The Low Pass filter is fixed at 160Hz.
N.B.The ASHDOWN 400 Watt powered sub unit can also be used with other systems as it has its own
active Low Pass Filter already built in.
OUTPUT LEVEL
The OUTPUT control adjusts the overall level of the amplifier. Adjust this for your preferred overall stage
playing volume.
Rear Panel Facilities
ABM, MAG & ELECTRIC BLUE
300 / 500 WATT ABM HEAD / COMBO
900 WATT ABM HEAD / COMBO
LINE INPUT (ABM only)
The rear panel has a Line Input socket for connection of other signal sources into the system. This can be
used for plugging a CD, Tape or MiniDisc player into the amplifier for practising or rehearsing or for
connection of a second preamp into the system.
EFFECTS SEND / RETURN (rear panel on ABM & front panel on MAG & Electric Blue)
A serial effects loop is provided at a level of 0dB. The Effects Send and Return sockets for this are on the
rear panel of the ABM and front panel of the MAG and Electric Blue below the D.I. socket. The EFFECTS
SEND socket can also be used as a Line Out socket if required. The signal path through the preamp is only
broken when a jack plug is inserted into the EFFECTS RETURN socket.The EFFECTS SEND is situated
after the EQ,Valve section and Sub Bass Processor (after the EQ on the Electric Blue).
MUTE FOOTSWITCH SOCKETS (ABM only)
Two jack sockets, marked OUTPUT and SUB, are provided for connection of foot switches to operate the
Output Muting and the Sub Harmonics facility these operate as follows. The OUTPUT foot switch
operates in the same way as the PUSH TO MUTE button on the front panel (see relevant section) and
mutes the output when closed. The SUB foot switch mutes the SUB HARMONICS when closed. For this
to operate, the SUB HARMONICS must already be activated with the front panel push switch.
EQ / SHAPE FOOTSWITCH SOCKETS (ABM only)
A single stereo jack socket is used for connection of a dual foot switch for remote switching of the EQ
(Graphic) and SHAPE (Push Flat) facilities. The TIP connection of this socket operates the EQ and the
RING connection the SHAPE. For this footswitch to operate, the front panel push switches for PUSH FLAT
and GRAPHIC must be in their OUT position.
CROSSOVER AND OUTPUTS (Rack Preamp RPM1 only)
The BASS MAGNIFIER RACK PREAMP RPM1 has a built in high precision CROSSOVER with separate jack
socket outputs for the HIGH PASS and LOW PASS signals. Crossover frequency is adjustable from 35Hz to
160Hz with a level control for the LOW PASS output to adjust the balance between LOW and HIGH
outputs signals. There is also a FULL RANGE jack line output provided. This section is provided with
switched output levels for simplified connection to power amplifiers that require either a 0dB or +4dB
signal level. This switches the levels of all three outputs.
SPEAKER OUTPUT (except Rack Preamp RPM1)
The Speaker Output sockets are also situated on the rear panel of the unit.
The lightning flash with the arrow head symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated `dangerous voltage' within this product's
enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying this product.
GROUNDING INSTRUCTIONS
This product must be grounded (earthed). If it should malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce the risk of electric shock. This
product is equipped with a supply cord having an equipment grounding conductor and a
grounding plug. The plug must be plugged into an appropriate outlet that is properly installed
and grounded in accordance with the local codes and ordinances.
DANGER - Improper connection of the equipment grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or serviceman if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the product
if it will not fit the outlet, have a proper outlet fitted.
The wires in this mains cord are coloured in accordance with the following code:
Green & Yellow - Earth Blue - Neutral Brown - Live
CE MARK FOR EUROPEAN HARMONISED STANDARDS
The CE mark which is attached to these products means it conforms to EMC Directive
(89/69/EEC), CE mark Directive (93/68/EEC) and Low Voltage Directive (72/23/EEC).