Text preview for : CW29Z68PSG_chassis K55A.pdf part of samsung CW29Z68PSG_chassis K55A chassis K55A
Back to : CW29Z68PSG_chassis K55A.p | Home
COLOR TELEVISION RECEIVER
Chassis : K55A(P) Model : CW29Z68PSGXXEC CW29Z68TSGXXEC
COLOR TELEVISION RECEIVER
CONTENTS
1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded Views and Parts List 7. Electrical Parts List 8. Block Diagrams 9. Schematic Diagrams
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the Xray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ! ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
Samsung Electronics
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
CAUTION
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
1-4
Samsung Electronics
Reference Information
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
Table 2-1 Abbreviations A Ah Å dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour
Samsung Electronics
2-1
Reference Information
Table 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor
2-2
Samsung Electronics
Reference Information
2-2 IC Line Up
Table 2 - 3 IC Line - Up NO BOARD LOC. NO IC901 HIC401 TU02S IC06 IC805 HC401 D801S HC801 IC602 IC801S 1 MAIN IC301 IC902 IC401 IC803 IC601 TU01S IC402 IC804 IC904 IC202 Q402 IC903 IC06 IC11 IC03 2 IC10 F-BOX IC05 IC02 IC01 IC04 PART NUMBER A09-00041A AA13-AAA94A A40-00084A 1203-002000 1203-001006 0502-001230 0402-001399 1230-001006 1201-001385 1203-002512 1204-000517 1103-001177 1202-000103 1203-001225 1204-001971 AA40-00083A 1203-000243 1203-001217 1203-001943 1203-001944 0505-001116 1203-001944 1203-002000 0801-000662 1001-001082 1001-001177 203-002186 1204-001814 1204-001938 1204-001989 IN NAME SDA555X-OTP DDRI001A TCPS300PC16B(S) DETECTOR;7027 78R05 FJL6920YDTU GSIB660 78R05 7269A KA5Q1565RF LA7845 24WC16 393, DIP, 8P 78R09 MSP3411G-B11 TCLS3101PD16A(S) 7812A 431 7025 78RM33 BUZ73A 78RM33 7027 74HC123 BA7657F TEA6425D 18, DPAK CXA2151Q VSP9407B-B11 CXA2165Q DESCRIPTION IC-MCU IC HYBRID TUNER-F/S IC-VOL IC-VOLTAGE REGULATOR TR-POWER DIODE-BREDGE IC-VOLTAGE REGULATOR IC-POWER AMP IC-PWM CONTROLLER IC-VERTICAL DEF IC-EEPROM IC-VOLTAGE COMP IC-POSLFIXED REG IC-SOUND PROCESSOR TUNER-F/S IC-POSLFIXED REG IC-POSLADJUST REG IC-VOL DETECTOR IC-POSLFIXED REG FET-SILICON IC-POSLFIXED REG IC-VOL DETECTOR IC-CMOS LIGIC IC-VIDEO SWITCH IC-VIDEO SWITCH IC-POSLFIXED REG IC-SELECTOR IC-ECODER IC-VIDEO PROCESS
Samsung Electronics
2-3
Reference Information
Table 2 - 3 IC Line - Up NO BOARD LOC. NO QF10 QF09 3 CRT IC501 IC502 IC503 IC504 MICOM 4 200PAGE -TTX (Europe) ICM02 ICM04 ICM04 ICM01 PART NAME 0502-000153 0502-000131 1201-001131 1201-001131 1201-001131 1201-000010 1102-001133 1203-001943 1106-001367 1204-001912 IC NAME SC2344-D 2SA1011-D 6111Q 6111Q 6111Q 2030 M27W201 7025 K6R4008CIC SDA555OM DESCRIPTION TR-POWER TR-POWER IC-VIDEO AMP IC-VIDEO AMP IC-VIDEO AMP IC-OP AMP IC-EPROM IC-VOL, DETECTOR IC-SRAM IC-DECODER
2-4
Samsung Electronics
Specifications
3. Specifications
Broadcasting System Tuning System
PAL/SECAM/NTSC Electronic Remote Control System VHF(CH2 ~ 12)
Receiving Channels
UHF(CH21 ~ 69) CATV(S1 ~ S41)
Antenna Input Resistance
VHF, UHF 75 unbalanced Video : 38.9MHz
Intermediate Frequency
Sound : 33.4MHz Chrominance Subcarrier : 34.47MHz
Power Supply
AC 160V ~ 300V or AC 100V ~ 240V, 50Hz
Samsung Electronics
3-1
MEMO
3-2
Samsung Electronics
Alignment and Adjustments
4. Alignment and Adjustments
4-1 Adjustments
4-1-1 General Alignment Instructions
Usually, a color TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as vertical size, horizontal size, and focus. Observe the picture and check for good black and white details. There must be no objectionable color shading: If color shading is present, demagnetize the receiver. If color shading persists, re-do purity and convergence adjustments. Note : 1. This `4. Alignment and Adjustments' applies to K55A chassis applications. 2. AC Power Supply: 160~300V or 100~240V, 50Hz 3. This service manual has been written on the basis of domestic remote-control model adopting K55A chassis. Depending on sales location and product specifications, some of specifications herein may be changed.
4-1-2 Focus Adjustment
K55A contains a dynamic focus circuit. When CRT PCB, FBT or CRT is replaced, be sure to adjust in the following sequence: Dynamic Focus Adjustment 1. Input a crosshatch pattern. 2. Select "Standard" from the menu, 3. Turn the Static Focus VR clockwise to set it to its maximum. 4. Turn the Dynamic Focus VR counterclockwise to set it to its maximum. 5. Turn the Static Focus VR counterclockwise slowly for the clearest center vertical line.
After Adjustment
6. Turn the Dynamic Focus VR clockwise slowly for the clearest third line.
1 2 3
7. Check for the FOCUS of entire screen. If necessary, re-do adjustments 3~6.
Samsung Electronics
4-1
Alignment and Adjustments
4-1-3 Screen Voltage Adjustment
1. Input a Toshiba pattern. 2. Use an oscilloscope to identify RK, BK, GK. And then adjust FBT Screen VR so that the voltage of pedestal level doesn't exceed 160V. If a Toshiba pattern is not available, cancel the blue screen and input "No Signal" to AV IN so the voltage of pedestal level doesn't exceed 175V. If an oscilloscope is not available, use a DC multi-meter in No Signal (black screen) to adjust RK, BK, GK so that the highest voltage becomes 160Vp-p.
4-1-4 White Balance Adjustment
1. Warm up the TV set for at least 30 minutes. 2. Enter the Service Mode by pressing the remote control keys in the following sequence: Power Off © Display © Menu © Mute © Power On 3. Initialize all set data. 4. Input a Toshiba pattern. 5. Using a probe(CA100), do the White Balance adjustments. (1) Adjust Low-Light. - Adjust Sub Brightness to set Y. - Adjust B Cutoff to set y. - Adjust R Cutoff to set x. (2) Adjust High-Light. - Adjust Sub Contrast to set Y. - Adjust B Drive to set y. - Adjust R Drive to set x. (3) Check the value of Low-Light. If necessary, readjust Low-Light. (4) Check the value of High-Light. If necessary, readjust High-Light.15
4-2
Samsung Electronics
Alignment and Adjustments
4-1-5 When adjusting Screen Voltage and White Balance
1. Screen Voltage and White Balance are related each other. Make sure both adjustments are correct. 2. Adjust Screen Voltage before White Balance Adjustments. Make sure Screen Voltage is correct. 3. If White Balance has been readjusted, re-check Screen Voltage. 4. After adjustments are complete, check the following. - If spots appear on the screen after pressing the Power On/Off key, readjust Screen Voltage. - If flyback lines appear on the screen, readjust Screen Voltage.
Samsung Electronics
4-3
Alignment and Adjustments
4-2 MICOM PORT
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 33 34 35 4-4 FUNCTION W-PORT ROM SDA ROM SCL BUS-STOP MAIN SDA MAIN SCL S-RESET V-RESET VDD 2.5V GND VDD3.3V CVBS IN VDD2.5V GND AFT SC1-ID SC2-ID KEY-1 H-SYNC V-SYNC KEY-3 KEY-2 X-RAY IR-IN STD-LED TIM-LED RELAY SW1 GND VDD 3.3V RESET X-IN X-OUT HIGH LOW Reset active : HIGH Crystal oscillation input jack Samsung Electronics HIGH HIGH LOW HIGH POSITIVE POSITIVE HIGH HIGH HIGH RANGE 16 : 9 MODE 0 ~ 2V Main AFT Control jack(0 ~ 3.3V) TV MODE 0 ~ 2V MEMU 0~0.1V VOL0.1~0.7V AV MODE 16 : 9 MODE 4.5 ~ 7V VOL+ 07~13V 4 : 3 MODE 9.5 ~ 12V HIGH IV p-p HIGH TTX and USA Caption Input source line(1V p-p) FIRST STATE HIGH SERIAL H SERIAL H HIGH SERIAL H SERIAL H HIGH HIGH HIGH Analog GND ASSIGNMENT RESET Control jack during E2PROM latch UP(Function:Low)SERIAL H E2PROM only SDA LINE E2PROM only SDA LINE Automation and after-sales service related BUS STOP(STOP : LOW) CXA2165 /CXA2151Q/VSP940X/BA7654F/MSP34XX/TUNER Control jack CXA2165 /CXA2151Q/VSP940X/BA7654F/MSP34XX/TUNER Control jack Reset when MSP34XX IC(SOUND PROCESS IC)has an error(Active : LOW) Reset when VSP940X IC(1-chip IC)has an error
CHCH+ 1.3~1.9V 0.9~2.4V
MICOM "H-SYNC" Input, POSITIVE Input(3.3V p-p) MICOM "V-SYNC" Input, POSITIVE Input(3.3V p-p) OPEN TV/VIDEO switching control jack Function : LOW Remote Control Input Jack STAND BY : Hight, OFF : LOW TIME ON : H TIME OFF : L
DEGAUSSIGN COIL CONTROL:Based on standard specifications H : IN1, L : IN2(BA7657F) PIN(#16) Control jack
Alignment and Adjustments
PIN 36 37 38 39 40 41 42 43 44 45 46 47
FUNCTION GND VDD 2.5V OSD-R OSD-G OSD-B CPRE VDD 2.5V GND VDD 3.3V PX, Y PX, Y SW3
FIRST STATE
ASSIGNMENT
HIGH 1.2V p-p 1.2V p-p 1.2V p-p 0.9V p-p HIGH OSD R-OUT Output jack (0.38V p-p), half tone : 0.9V p-p OSD G-OUT Output jack (0.38V p-p), half tone : 0.9V p-p OSD B-OUT Output jack (0.38V p-p), half tone : 0.9V p-p OSD F/B-OUT Output jack (Clamped at STAND PULSE, Half Tone : LOW)
HIGH HIGH HIGH H F1 L M F0 M L fH 1.75KHz (480i/480P) 33.75KHz (1080i)
48
SW2
L
LOW : GNDHIGH : OPEN STATUS Initially, these pins select an input source at LOW state
49 50 51 52
S-MUTE POWER H,P-ID TILT HIGH
System (NTSC/PAL) MUST be separated Active "LOW" 1080i control jack : 1080i (LOW), RF (Hight) Magnetic field control
Samsung Electronics
4-5
Alignment and Adjustments
4-3 Factory Adjustment
4-3-1 Factory Adjustment values SERVICE Deflection 480P Offset 1080i Offset Video Adjust1 Video Adjust2 Video Adjust3 Option YC Delay EEPROM Reset
4-3-2 EUROPE & CIS Factory Data
DEFLECTION : PAL
50 2.5 ITEMS V-AMP V-SHIFT H-EW H-SHIFT V-LIN(Fix) UP-LIN(Fix) LOW-LIN(Fix) V-SC(Fix) H-PAR UP-COR LOW-COR H-TRA BOW ANGLE V-POSI(Fix) 4-6 29" CIS SDI CRT 33 28 26 0 9 9 4 3 38 25 31 18 33 28 35 -> 40 45 2 32" CIS SDI CRT 33 28 32 0 9 9 3 1 38 25 31 18 33 28 40 50 2.5 34" CIS TOS CRT 26 24 17 26 9 9 2 3 51 35 36 42 31 30 40 37 1.8 29" EUR SDI CRT 33 28 26 0 9 9 4 3 38 25 31 18 33 28 35 -> 40 37 1.5 32" EUR PHI CRT 41 26 36 21 11 9 1 0 19 33 33 43 33 28 40 Vertical AMP adj(Gain Control) Vertical Position adj(DC bias adj) Horizontal AMP adj(Gain Control) Horizontal Position adj(DC bias adj) Vertical Linearity adj(Top/Bottom adj) Vertical Linearity adj(Top adj) Vertical Linearity adj(Bottom adj) Vertical S correction adj Horizontal pin distortion adj Horizontal pin distortion up adj Horizontal pin distortion low adj Horizontal Tapezium distortion adj Vertical line slope adj(parabola) Vertical Linearity adj(sawtooth) V-Position adj as to CRT inch Samsung Electronics
H/L : 285/285 29" CIS, EU W/B COORDINATE L/L : 285/285
REMARK
Alignment and Adjustments
DEFLECTION : NTSC
29" CIS SDI CRT -7 -4 5 30 -4 -1 3 0 8 7 3 7 -1 -1 0 32" CIS SDI CRT -7 -4 5 30 -4 -1 3 0 8 7 3 7 -1 -1 0 34" CIS TOS CRT -7 -4 5 30 -4 -1 3 0 8 7 3 7 -1 -1 0 29" EUR SDI CRT -7 -4 5 30 -4 -1 3 0 8 7 3 7 -1 -1 0 32" EUR PHI CRT 0 -1 1 3 -4 -1 3 0 1 2 -1 0 0 0 0
ITEMS V-AMP V-SHIFT H-EW H-SHIFT V-LIN UP-LIN LOW-LIN V-SC H-PAR UP-COR LOW-COR H-TRA BOW ANGLE V-POSI
REMARK Vertical AMP adj(Gain Control) Vertical Position adj(DC bias adj) Horizontal AMP adj(Gain Control) Horizontal Position adj(DC bias adj) Vertical Linearity adj(Top/Bottom adj) Vertical Linearity adj(Top adj) Vertical Linearity adj(Bottom adj) Vertical S correction adj Horizontal pin distortion adj Horizontal pin distortion up adj Horizontal pin distortion low adj Horizontal Tapezium distortion adj Vertical line slope adj(parabola) Vertical Linearity adj(sawtooth) V-Position adj as to CRT inch
Samsung Electronics
4-7
Alignment and Adjustments
Video Adjust 1
29" CIS SDI CRT 41 25 28 1 32 32 37 32 32 32 7 15 28 1 1 1 2 7 32" CIS SDI CRT 41 25 28 1 32 32 37 32 32 32 7 15 28 1 1 1 2 7 34" CIS TOS CRT 46 32 18 1 32 32 46 32 26 40 7 10 28 1 1 1 2 7 29" EUR SDI CRT 41 32 28 1 32 32 37 32 32 32 7 15 28 1 1 1 2 7 32" EUR PHI CRT 41 32 38 1 32 32 40 32 38 47 7 15 28 1 1 1 2 7
ITEMS R-Cutoff G-Cutoff(Fix) B-Cutoff Color on/off CR offset CB offset R-Drive G-Drive(Fix) B-Drive Sub-Bright Sub-Contrast Sub-Color(Fix) Sub-TInt(Fix) CTI-Level(Fix) COL AXIS(Fix) LTI-Level(Fix) VSU(Fix) Merody Volume(Fix)
REMARK R-cutoff control adj G-cutoff control adj B-cutoff control adj initial : "0" -> 1 DC-offset canceling adjust DC-offset canceling adjust R-Drive control adj G-Drive control adj B-Drive control adj Sub-Bright control Sub-Contrast control color gain control(PAL SETTING AGAIN) HUE control Chrominance Transient Improvement color detection axis setting(NTSC/USA) Luminance Transient Improvement vertical osd position Volume gain control
4-8
Samsung Electronics
Alignment and Adjustments
Video Adjust 2
29" CIS SDI CRT 3 2 3 3 14 1 2 2 2 3 1 0 8 13 17h 23h 32" CIS SDI CRT 3 2 3 3 15 1 2 2 2 3 1 0 8 13 17h 23h 34" CIS TOS CRT 3 2 3 3 14 1 2 2 2 3 1 0 8 13 17h 23h 29" EUR SDI CRT 3 2 3 3 14 1 2 2 2 3 1 0 8 13 17h 23h 32" EUR PHI CRT 3 2 3 3 14 1 2 2 2 3 1 0 8 13 17h 23h
ITEMS ABL Mode Gamma DPIC Level DC Trans ABL-TH VM-Level VM-Coring VM-f0 VM-Limit VM-Delay SHP CD SHP f0 SHP f1&p/o AKB Time Bandpass Highpass
REMARK Rpicture/bright ABL gain control RGB output correction control Dynamic picture black expansion control Y-System DC transmission ratio Threshold voltage adj ABL-IN VM-OUT Level control VM-OUT coring control VM-f0 control VM-Limit level control VM-OUT phase control(reference to R-OUT) Sharpness gain control(color satuation) Sharpness f0 control (3Mhz) Sharpness gain control(PAL SETTING AGAIN) AKB Bch reference pulse time control VSP9407B Band pass filter VSP9407B High pass filter
Video Adjust 3
29" CIS SDI CRT 7 4 2 0 0 6 32" CIS 34" CIS 29" EUR 32" EUR PHI CRT 6 4 2 0 0 6
ITEMS H comp V comp PIN comp AFC comp sync phase NR Value
SDI CRT TOS CRT SDI CRT 8 5 2 0 0 6 4 4 7 0 0 6 7 4 7 0 0 6
REMARK H-EHT compensation setting(PAL SETTING AGAIN) V-EHT compensation setting(PAL SETTING AGAIN) PIN-EHT compensation setting(PAL SETTING AGAIN) AFC-EHT compensation WHEN USED 74HC123 PAL SETTING AGAIN
Samsung Electronics
4-9
Alignment and Adjustments
Option Byte(CIS Model)
29" CIS 32" CIS 34" CIS 29" EUR SDI CRT NON 32" EUR PHI CRT NON CIS/ARAB
ITEMS Language SOUND CRT AV JACK AUTO FM PIP TXT LANGUAGE LNA HIGH DEVIATION AV BY CH KEY DTV VGA AGC WOOFER SPEAKER TTX TOP HELP TTX ON/OFF TTX LIST PRIARITY
SDI CRT SDI CRT TOS CRT CIS CIS CIS
REMARK
V-DOLBY V-DOLBY V-DOLBY V-DOLBY 4:3 SCART ON ON ON ON OFF OFF OFF OFF OFF OFF NON NON NON NON NON WIDE SCART ON ON ON ON OFF OFF OFF OFF OFF OFF NON NON NON NON NON 4:3 SCART ON ON ON OFF OFF OFF OFF OFF OFF NON NON NON NON NON NON WIDE SCART ON ON
V-DOLBY V-DOLBY/A2-NICAM WIDE SCART ON ON SCART(CIS,EUROPE)/RCA(ASIA,AUSTRAILIA) ON/OFF ON/OFF(W/O PIP MODEL) OPTION ON/OFF(1 TUNER) OFF/ON(INDIA) OFF/ON OFF/ON OFF/OFF OFF/ON OFF/ON
WESTERN WESTERN EUROPE ON OFF OFF OFF OFF OFF OFF EUROPE ON OFF OFF OFF OFF OFF OFF
DOME SPK DOME SPK EQ CURVE(DOME/NON DOME SPK) OFF OFF ON NON OFF OFF ON NON OFF/ON OFF/ON OFF/ON OFF/ON
4-10
Samsung Electronics
Alignment and Adjustments
YC Delay
29" CIS SDI CRT 1 -5 2 0 -2 -1 0 0 -6 -9 -9 0 0 32" CIS SDI CRT 1 -5 2 0 -2 -1 0 0 -6 -9 -9 0 0 34" CIS TOS CRT 1 -5 2 0 -2 -1 0 0 -6 -9 -9 0 0 29" EUR SDI CRT 2 -5 4 4 2 1 0 0 -2 -7 -9 -5 0 32" EUR PHI CRT 2 -5 4 4 2 1 0 0 -2 -7 -9 -5 0
ITEMS P.YC(AV) DELAY S.YC(AV) DELAY N.YC(AV) DELAY P.BG.YC DELAY P.DK.YC DELAY P.I.YC DELAY P.M.YC DELAY P.L.YC DELAY S.BG.YC DELAY S.DK.YC DELAY S.I.YC DELAY S.L.YC DELAY N.M.YC DELAY
REMARK
Samsung Electronics
4-11
Alignment and Adjustments
EUROPE & CIS EEPROM Data
29" CIS 32" CIS 34" CIS 29" EUR 32" EUR SDI CRT SDI CRT TOS CRT SDI CRT PHI CRT 1 1 2 1 6 7 70 40 60 60 50 50 40 40 50 50 50 50 30 40 50 45 50 50 76 186 255 255 255 255 0 124 125 0 0 2 1 5 7 70 40 60 70 50 50 50 40 50 60 50 50 35 40 50 55 50 50 78 187 255 255 255 255 0 124 125 0 0 2 1 13 11 100 40 60 60 50 50 60 42 50 50 50 50 40 40 50 45 50 50 76 184 255 255 255 255 0 124 125 0 0 1 2 6 7 70 50 40 60 50 50 50 45 40 50 50 50 40 45 40 45 50 50 76 186 255 255 255 255 0 124 125 0 0 1 2 5 7 100 50 40 60 50 50 80 50 40 50 50 50 60 50 40 45 50 50 76 190 255 255 255 255 0 124 125
F-No 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Factory Control Name UP-UCG(up corner semi control) LO-UCG(low corner semi control) LTI Mode System 50 Hz Progressive Trapezium 60 Hz Progressive Trapezium Dynamic Contrast Dynamic Brightness Dynamic Sharpness Dynamic Color Dynamic ColorTone Dynamic Tint Standard Contrast Standard Brightness Standard Sharpness Standard Color Standard ColorTone Standard Tint Movie Contrast Movie Brightness Movie Sharpness Movie Color Movie ColorTone Movie Tint PROGRESSIVE TTX V-POSITION PROGRESSIVE TTX H-POSITION
Range 0~3 0~3 0~3 0~3 0~255 0~255 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~255 0~255 0~100 0~100 0~100 0~100
REMARK
Brightness(RGB/DVD) Contrast(RGB/DVD) U Saturation(RGB/DVD)
0~255 0~255 0~255
4-12
Samsung Electronics
Alignment and Adjustments
F-No 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
Factory Control Name V saturation(RGB/DVD) 9407 Y Gain 9407 U Gain Luminance Delay(Fixed Value) 9407 V Gain Start Value of Lum LUT(Main)-NR_ON Noise Reduction(Main)-NR_ON Start Value of Lum LUT(PIP)-NR_ON Noise Reduction(PIP)-NR_ON Vertical End of Clamping Pulse SECAM Color Sensitivity(Main) Vertical End of Clamping Pulse SECAM Color Sensitivity(PIP) Left Blanking Right Blanking S-ABL P-ABL Start Value of Lum LUT(Main)-NR_OFF Noise Reduction(Main)-NR_OFF Start Value of Lum LUT(PIP)-NR_OFF Noise Reduction(PIP)-NR_OFF Picture Limit Level OSD LEVEL(LRGB2_LEV) TTX LEVEL(LRGB2_LEV) Left Blanking (480p) Right Blanking (480p) Left Blanking (1080i) Right Blanking (1080i) System (480p) System (1080i) CrCb Gain (480p) CrCb Gain (1080i) LTI Mode (480p)
Range 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~3 0~15 0~15 0~255 0~255 0~255 0~255 0~3 0~3 0~255 0~255 0~3
29" CIS 32" CIS 34" CIS 29" EUR 32" EUR SDI CRT SDI CRT TOS CRT SDI CRT PHI CRT 248 93 83 8 82 255 102 255 102 28 28 28 28 147 153 0 48 255 255 255 255 3 7 0 0 0 0 0 0 0 0 0 0 248 93 83 8 82 255 102 255 102 28 28 28 28 147 153 0 64 255 255 255 255 3 7 0 0 0 0 0 0 0 0 0 0 248 93 83 8 82 255 102 255 102 28 28 28 28 147 153 0 48 255 255 255 255 3 10 0 0 0 0 0 0 0 0 0 0 248 80 71 8 70 255 102 255 102 28 28 28 28 147 153 0 48 255 255 255 255 3 7 5 0 0 0 0 0 0 0 0 0 248 80 71 8 70 255 102 255 102 28 28 28 28 147 153 0 48 255 255 255 255 3 7 5 0 0 0 0 0 0 0 0 0
REMARK
Samsung Electronics
4-13
Alignment and Adjustments
F-No 66 67 68 69 70 71
Factory Control Name LTI Mode (1080i) TTX V Position TTX H Position 16 PIP UPPER CORNER OFF SET 16 PIP LOWER CORNER OFF SET 4:3 Normal Parabola
Range 0~3 0~255 0~255 0~255 0~255 0~255
29" CIS 32" CIS 34" CIS 29" EUR 32" EUR SDI CRT SDI CRT TOS CRT SDI CRT PHI CRT 0 37 186 2 1 0 0 37 188 4 0 0 0 37 185 3 3 0 0 37 186 2 1 0 0 38 190 4 0 0
REMARK
4-14
Samsung Electronics
Alignment and Adjustments
4-3-3 AISA Factory Data
DEFLECTION : PAL
29" AISA SDI CRT 35 22 40 22 7 9 4 1 33 18 27 24 33 31 40 32" Australia LG CRT 24 27 34 21 9 9 3 1 20 32 35 32 32 30 40 29" Australia SDI CRT 39 27 31 17 9 9 4 3 39 31 32 36 35 26 40
ITEMS V-AMP V-SHIFT H- EW H-SHIFT V-LIN UP-LIN LOW-LIN V-SC H-PAR UP-COR LOW-COR H-TRA BOW ANGLE V-POSI
REMARK Vertical AMP adj(Gain Control) Vertical Position adj(DC bias adj) Horizontal AMP adj(Gain Control) Horizontal Position adj(DC bias adj) Vertical Linearity adj(Top/Bottom adj) Vertical Linearity adj(Top adj) Vertical Linearity adj(Bottom adj) Vertical S correction adj Horizontal pin distortion adj Horizontal pin distortion up adj Horizontal pin distortion low adj Horizontal Tapezium distortion adj Vertical line slope adj(parabola) Vertical Linearity adj(sawtooth) V-Position adj as to CRT inch
Samsung Electronics
4-15
Alignment and Adjustments
DEFLECTION : NTSC
ITEMS V-AMP V-SHIFT H- EW H-SHIFT V-LIN UP-LIN LOW-LIN V-SC H-PAR UP-COR LOW-COR H-TRA BOW ANGLE V-POSI 29" AISA SDI CRT 1 0 -2 10 -4 -1 2 0 1 4 -3 4 0 0 0 32" Australia LG CRT 2 -2 0 8 -4 -1 3 0 0 1 -3 0 0 0 0 29" Australia SDI CRT 1 -2 -1 9 -4 -1 2 0 2 2 -3 4 1 -1 0 REMARK Vertical AMP adj( Gain Control) Vertical Position adj (DC bias adj) Horizontal AMP adj(Gain Control) Horizontal Position adj (DC bias adj) Vertical Linearity adj(TOP/Bottom adj) Vertical Linearity adj(TOP adj) Vertical Linearity adj(Bottom adj) Vertical S correction adj Horizontal pin distortion adj Horizontal pin distortion up adj Horizontal pin distortion low adj Horizontal Trapezium distortion adj Vertical line slope adj(parabola) Vertical Linearity adj(sawtooth) V-POSITION ADJ as to CRT INCH
480p Offset
ITEMS V-AMP V-SHIFT H- EW H-SHIFT V-LIN UP-LIN LOW-LIN V-SC H-PAR UP-COR LOW-COR H-TRA BOW ANGLE V-POSI 4-16 29" AISA SDI CRT -1 1 8 -9 0 0 0 0 0 0 0 -7 0 0 0 32" Australia LG CRT 2 -3 4 -7 -4 -1 3 0 -4 3 -3 4 0 1 0 29" Australia SDI CRT -8 2 3 -9 0 -1 -3 2 1 -1 -1 3 2 0 0 REMARK Vertical AMP adj( Gain Control) Vertical Position adj (DC bias adj) Horizontal AMP adj(Gain Control) Horizontal Position adj (DC bias adj) Vertical Linearity adj(TOP/Bottom adj) Vertical Linearity adj(TOP adj) Vertical Linearity adj(Bottom adj) Vertical S correction adj Horizontal pin distortion adj Horizontal pin distortion up adj Horizontal pin distortion low adj Horizontal Trapezium distortion adj Vertical line slope adj(parabola) Vertical Linearity adj(sawtooth) V-POSITION ADJ as to CRT INCH Samsung Electronics
Alignment and Adjustments
1080i Offset
ITEMS V-AMP V-SHIFT H- EW H-SHIFT V-LIN UP-LIN LOW-LIN V-SC H-PAR UP-COR LOW-COR H-TRA BOW ANGLE V-POSI 29" AISA SDI CRT -14 2 6 4 0 0 0 0 0 0 0 0 0 0 0 32" Australia LG CRT -1 -2 -10 11 0 0 0 0 3 5 3 2 -1 1 0 29" Australia SDI CRT -4 -1 2 10 -1 0 -1 0 -1 0 1 -3 1 2 0 REMARK Vertical AMP adj( Gain Control) Vertical Position adj (DC bias adj) Horizontal AMP adj(Gain Control) Horizontal Position adj (DC bias adj) Vertical Linearity adj(TOP/Bottom adj) Vertical Linearity adj(TOP adj) Vertical Linearity adj(Bottom adj) Vertical S correction adj Horizontal pin distortion adj Horizontal pin distortion up adj Horizontal pin distortion low adj Horizontal Trapezium distortion adj Vertical line slope adj(parabola) Vertical Linearity adj(sawtooth) V-POSITION ADJ as to CRT INCH
Samsung Electronics
4-17
Alignment and Adjustments
Video Adjust 1
29" AISA SDI CRT 41 32 28 1 32 32 37 32 32 32 7 15 28 1 1 1 2 4 32" Australia LG CRT 31 32 43 1 32 32 37 32 43 33 7 15 28 1 1 1 2 4 29" Australia SDI CRT 41 32 28 1 32 32 37 32 32 32 7 15 28 1 1 1 2 4
ITEMS R-Cutoff G-Cutoff B-Cutoff Color on/off CR offset CB offset R-Drive G-Drive B-Drive Sub-Bright Sub-Contrast Sub-Color Sub-Tint CTI-Level COL AXIS LTI-Level VSU Merody Volume
REMARK R-cutoff control adj G-cutoff control adj B-cutoff control adj Fixed :"0"--> 1 DC-offset canceling adjust DC-offset canceling adjust R-Drive control adj G-Drive control adj B-Drive control adj Sub-Bright control Sub-Contrast control color gain control(PAL SETTING AGAIN) HUE control Chrominance Transient Improvement color detection axis setting(NTSC/USA) Luminance Transient Improvement vertical osd position Volume gain control
4-18
Samsung Electronics
Alignment and Adjustments
Video Adjust 2
29" AISA SDI CRT 3 2 3 3 14 1 2 2 2 3 1 0 8 13 17 23 32" Australia LG CRT 3 2 3 3 15 1 2 2 2 3 1 0 8 13 17 23 29" Australia SDI CRT 3 2 3 3 14 1 2 2 2 3 1 0 8 13 17 23
ITEMS ABL Mode Gamma DPIC Level DC Trans ABL-TH VM-Level VM-Coring VM-f0 VM-Limit VM-Delay SHP CD SHP f0 SHP f1&p/o AKB Time Bandpass Highpass
REMARK picture/bright ABL gain control RGB output correction control Dynamic picture black expansion control Y-System DC transmission ratio Threshold voltage adj ABL-IN VM-OUT Level control VM-OUT coring control VM-f0 control VM-Limit level control VM-OUT phase control(reference to R-OUT) Sharpness gain control(color satuation) Sharpness f0 control (3Mhz) Sharpness gain control(PAL SETTING AGAIN) AKB Bch reference pulse time control VSP9407B Band pass filter VSP9407B High pass filter
Video Adjust 3
29" AISA SDI CRT 7 4 2 0 0 6 1 0 32" Australia LG CRT 6 4 2 0 0 6 1 0 29" Australia SDI CRT 7 4 2 0 0 6 1 0
ITEMS H comp V comp PIN comp AFC comp sync phase NR Value sync phase(480p) sync phase(1080i)
REMARK H-EHT compensation setting(PAL SETTING AGAIN) V-EHT compensation setting(PAL SETTING AGAIN) PIN-EHT compensation setting(PAL SETTING AGAIN) AFC-EHT compensation WHEN USED 74HC123 PAL SETTING AGAIN WHEN USED 74HC123 WHEN USED 74HC123
Samsung Electronics
4-19
Alignment and Adjustments
DTV Adjust (480p/1080i)
29" AISA SDI CRT 19 7 15 28 1 2 1 2 2 2 3 1 0 8 32" Australia LG CRT 38 7 15 28 1 2 1 2 2 2 3 1 0 8 29" Australia SDI CRT 19 7 15 28 1 1 1 2 2 2 3 1 0 8
ITEMS Sub-Bright Sub-Contrast Sub-Color Sub-Tint COL AXIS LTI-Level VM-Level VM-Coring VM-f0 VM-Limit VM-Delay SHP CD SHP f0 SHP f1 & p/o
REMARK
Option Byte(ASIA Model)
29" AISA SDI CRT Asia V-DOLBY 4:3 RCA ON ON ON ON OFF OFF ON OFF OFF OFF 32" Australia LG CRT ASIA V-DOLBY WIDE RCA ON ON ON ON OFF OFF ON OFF OFF OFF 29" Australia SDI CRT ASIA V-DOLBY 4:3 RCA ON ON ON ON OFF OFF ON OFF OFF OFF SCART(CIS,EUROPE)/RCA(ASIA,AUSTRAILIA) ON/OFF ON/OFF(W/O PIP MODEL) RUSSIA/GREEK-TURKEY/ARABIC/FARSI/ ARAB-HEBREW/WEST EUROPE/EAST EUROPE ON/OFF(1 TUNER) OFF/ON(INDIA) OFF/ON OFF/ON OFF/OFF OFF/ON OFF/ON (Z7PART : ON, OTHERS : OFF) Samsung Electronics CIS/ARAB V-DOLBY/A2-NICAM
ITEMS Language SOUND CRT AV JACK AUTO FM PIP TXT LANGUAGE LNA HIGH DEVIATION AV BY CH KEY DTV VGA AGC WOOFER 4-20
REMARK
Alignment and Adjustments
YC Delay
29" AISA SDI CRT 1 -5 2 0 -2 -1 0 0 -6 -9 -9 0 0 0 32" Australia LG CRT 1 -5 2 0 -2 -1 0 0 -6 -9 -9 0 0 0 29" Australia SDI CRT 1 -5 2 0 -2 -1 0 0 -6 -9 -9 0 0 0
ITEMS P.YC(AV) DELAY S.YC(AV) DELAY N.YC(AV) DELAY P.BG.YC DELAY P.DK.YC DELAY P.I.YC DELAY P.M.YC DELAY P.L.YC DELAY S.BG.YC DELAY S.DK.YC DELAY S.I.YC DELAY S.M.YC DELAY S.L.YC DELAY N.M.YC DELAY
REMARK
High Voltage(kV) Beam Current(mA)
30.64kV 33.8kV 1.833mA
31.62kV 33.97kV 1.82mA
Lion-head(Dynamic mode)
Samsung Electronics
4-21
Alignment and Adjustments
ASIA EEPROM Data
29" AISA 32" Australia 29" Australia SDI CRT 1 1 2 1 6 7 90 50 50 60 50 50 70 50 50 50 50 50 50 50 50 45 50 50 76 186 32 255 32 184 0 124 125 LG CRT 0 0 2 1 7 7 100 50 50 60 50 50 80 50 40 50 50 50 60 50 40 50 50 50 78 187 32 255 32 184 0 124 125 SDI CRT 1 1 2 1 6 7 90 50 50 60 50 50 70 50 50 50 50 50 50 50 50 45 50 50 76 186 32 255 32 184 0 124 125
F-No 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Factory Control Name UP-UCG(up corner semi control) LO-UCG(low corner semi control) LTI Mode System 50 Hz Progressive Trapezium 60 Hz Progressive Trapezium Dynamic Contrast Dynamic Brightness Dynamic Sharpness Dynamic Color Dynamic ColorTone Dynamic Tint Standard Contrast Standard Brightness Standard Sharpness Standard Color Standard ColorTone Standard Tint Movie Contrast Movie Brightness Movie Sharpness Movie Color Movie ColorTone Movie Tint PROGRESSIVE TTX V-POSITION PROGRESSIVE TTX H-POSITION 1080i 50Hz OSD V-POSITION 1080i 50Hz OSD H-POSITION 1080i 60Hz OSD V-POSITION 1080i 60Hz OSD H-POSITION Brightness(RGB/DVD) Contrast(RGB/DVD) U Saturation(RGB/DVD)
Range 0~3 0~3 0~3 0~3 0~63 0~63 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~100 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255
REMARK
4-22
Samsung Electronics
Alignment and Adjustments
F-No 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65
Factory Control Name V saturation(RGB/DVD) 9407 Y Gain 9407 U Gain Luminance Delay(FIX) 9407 V Gain Start Value of Lum LUT(Main)-NR_ON Noise Reduction(Main)-NR_ON Start Value of Lum LUT(PIP)-NR_ON Noise Reduction(PIP)-NR_ON Vertical End of Clamping Pulse SECAM Color Sensitivity(Main) Vertical End of Clamping Pulse SECAM Color Sensitivity(PIP) Left Blanking Right Blanking S-ABL P-ABL Start Value of Lum LUT(Main)-NR_OFF Noise Reduction(Main)-NR_OFF Start Value of Lum LUT(PIP)-NR_OFF Noise Reduction(PIP)-NR_OFF Picture Limit Level OSD LEVEL(LRGB2_LEV) TTX LEVEL(LRGB2_LEV) Left Blanking (480p) Right Blanking (480p) Left Blanking (1080i) Right Blanking (1080i) System (480p) System (1080i) CrCb Gain (480p) CrCb Gain (1080i) LTI Mode (480p)
Range 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~255 0~3 0~15 0~15 0~255 0~255 0~255 0~255 0~3 0~3 0~255 0~255 0~3
29" AISA 32" Australia 29" Australia SDI CRT 248 93 83 8 82 255 102 255 102 28 28 28 28 147 153 0 48 255 255 255 255 3 12 5 195 165 167 125 1 1 119 119 1 LG CRT 248 93 83 8 82 255 102 255 102 28 28 28 28 147 153 0 48 255 255 255 255 3 12 5 195 165 167 125 1 1 119 119 1 SDI CRT 248 93 83 8 82 255 102 255 102 28 28 28 28 147 153 0 48 255 255 255 255 3 12 5 195 165 167 125 1 1 119 119 1
REMARK
Samsung Electronics
4-23
Alignment and Adjustments
F-No 66 67 68 69 70 71
Factory Control Name LTI Mode (1080i) TTX V Position TTX H Position 16PIP UPPER CORNER OFF SET 16 PIP LOWER CORNER OFF SET 4:3 Normal Parabola
Range 0~3 0~255 0~255 0~255 0~255 0~255
29" AISA 32" Australia 29" Australia SDI CRT 1 38 186 4 1 0 LG CRT 1 38 188 0 0 0 SDI CRT 1 38 186 4 1 0
REMARK
4-24
Samsung Electronics
Alignment and Adjustments
4-4 Screen Change(I2C Bus Geometric Adjustment)
0 V - Amp
8
H-Parabola
1
V-Shift
9
Upper Coner
2
H-EW
10 Low Coner
3 H-Shift
11
H- Trapezuim
4
V-Linearity
12
Bow
5
Upper Linearity
13
Angle
6
Low Linearity
14
V Position
7
V SC
Samsung Electronics
4-25
MEMO
4-26
Samsung Electronics
Troubleshooting
5. Troubleshooting
5-1 No Raster
Abnormal
Check ST-BY
Normal
Abnormal
Check ST5V Q804 "E"
Normal
Check VIN(DC) TS801S PIN 13
Normal
Abnormal
Check ON/OFF IC903 ; 3.3V
Normal
Abnormal
Check ST5V HC801"D809"
Normal
Check MICOM
Check MICOM
Check FA803S
Check FA801S
Normal GND SHORT
Abnormal
Check B+(135V)
Normal
Check F-BOX 5V, 9V
Abnormal
Check9V:R829, IC803 5V:R827, FA802S
Check HC401 J6920 Normal Normal Check Vin(dc)T801S Abnormal Abnormal Check DZ801,DZ802, DZ803,IC804 Check FP801S Check F-BOX I C Check HIC401 Q402 Check H-BLK V-BLK Check F-BOX HD,VD
Check CRT ASSY R529
REPLACE F-BOX
Samsung Electronics
5-1
Troubleshooting
5-2 No Sound
NO SOUND
Normal
Check the signal of CN601 Abnormal
Abnormal
Check SPEAKER and WIRE
Check the input signal of IC602 pins 7,11
Normal
Abnormal
Check the input signal of IC601
Check IC602 B+
Normal Check TUNER B+ and SIF Normal Replace IC602
Abnormal
Check FA803S
Check IC601 B+ Normal Check the signals of pins 47,44,are input Normal Check the signals of pins 25,24 are input Normal Repace IC601
Abnormal
CheckB+(BV) LINE R815, IC805, FA802S
5-2
Samsung Electronics
Troubleshooting
5-3 No Power
Plug in the Power Cord
Check Power LED
ST-BY : LED Nomal
Check the oscillation of X-Tal of IC901 pins 34, 35 Check Reset of IC901 pin 33
Abnomal
Check X901, IC904
Abnomal Nomal
Check IC901 B+ (3.3VDD) Abnomal
Check/Replace IC901 Check I2C Nomal
Check Q804
Abnomal HC801S FA801S FA802S Abnomal Check CN901, CN902
Check IC905 E2PROM
Nomal
Abnomal Check 135V Line
Nomal Check T444S FBT B+ Abnomal Check F-BOX (5V) Nomal Check IC801S, DZ801,DZ802, PC801S,IC804
Abnomal
Check TRANS(12V)
Check IC803, IC802,R827,R829
Nomal
Check the Horizontal TR of HC401 "J6920"
Check F-BOX HD/VD Abnomal
Check F-BOX I C
2
Check HIC401,Q402 Nomal
Check H-BLK, V-BLK Line
Replace F-BOX
Samsung Electronics
5-3
Troubleshooting
5-4 Horizontal Lines Appear
Horizontal lines appear
Nomal
Check IC301 B+ (16V, -13.5V)
Abnomal
Check B+ line and fusible resistance Nomal Check F-BOX B+ VD+, VDAbnomal Check / Replace IC301 Check IC802,IC803, HC801,FA801S,FA803S Abnomal
Replace R424, R425
5-4
Samsung Electronics
Exploded View & Parts List
6. Exploded View & Parts List
6-1 CW29Z68PSGXXEC
No 1 1* 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 2 2-1 2-2 2-3 3 3-1 3-2
Code No AA96-01182A AA64-02744H AA64-70117B AA63-00571A AA63-00569B 6003-001268 6003-001268 AA64-02752A AA64-02751A AA61-60003J AA64-02753A AA64-02750A 6003-001019 AA94-11730A 6003-000333 AA64-02662A 6003-001019 AA41-00651A AA96-01269A 6003-001268 AA91-00507B 6003-001024 AA91-06005A HA60-00142A AA65-30113A AA60-10050V AA64-02745D 6002-000515 AA96-01127C
Description;Specification ASSY COVER P-C/FRONT;29Z6,HIPS HB CABINET-FRONT;29Z6,K55A,SEH BADGE-BRAND;-,AL,-,-,L65,R2000,SILVER,SS COVER-A/V;29Z6,HIPS,HB,G4309,DGN-1189 COVER-CONTROL;29Z6,HIPS,HB,G4309,DGN-118 SCREW-TAPTITE;TH,+,B,M4.0,L12.0,ZPC(YEL) SCREW-TAPTITE;TH,+,B,M4.0,L12.0,ZPC(YEL) WINDOW-RMC;29Z6,PC,VO,VIOLET KNOB POWER;29Z6,PC,VO,VIOLET SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-, INDICATOR LED;29Z6,ACRYL,HB,CLEAR DECORATION-POWER;29Z6,ABS,HB,GRAY,AL SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR ASSY PCB MISC-MASTER;Z6,Z7Z9,K55A,S57A,P SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW KNOB-CONTROL;Z7,ABS,HB,G3676,S104M+W971 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR PCB-CONTROL;CS29Z7HF,FR-1,1L,A,1.6T,330X ASSY COVER P-AV;29Z6 SCREW-TAPTITE;TH,+,B,M4.0,L12.0,ZPC(YEL) ASSY HOLDER SPK;DP,-,8OHM/15W,-,29K1 CKD SCREW-TAPTITE;RWH,+,B,M4,L12,ZPC(YEL),SW ASSY CPT;4:3,FLAT,100HZ,29,A68QCP891X0 SPACER-GUM;,RUBBER,RED,T2.5,M5 CLAMPER CORE-D,COIL;-,NYLON 66,V2,-,BLK, SCREW-ASSY;-,SWRCH18A,M6,L30,HH,+,WC,-,Z CABINET-BACK;29Z6,K55A,SEH SCREW-TAPPING;RH,+,2,M4,L15,ZPC(WHT),SWR ASSY POWER CORD;DP,AA39-10001M,CP2,H/C50
Q'ty 1 1 1 1 1 2 2 1 1 1 1 1 2 1 2 1 2 1 1 3 1 8 1 4 4 4 1 7 1
Remark
S.N.A
ACAV+C ACC+CF
DP+CF HP+PCB Cover PCB AV+CV SPK+CF
CRT+CF
CB+CF
Samsung Electronics
6-1
Electrical Parts List
7. Electrical Parts List
7-1 CW29Z68PSGXXEC
Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark
ASSY CHASSIS
1 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 2 3 3 3 3 4 4 4 4 4 4 4 4 4 4 4 2 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 WP+HC MP+HC C-BLOC TBA+HC PCB AA91-05852A ASSY CHASSIS;CW29Z68PSGXXEC,K55A,EU,SEB 6003-000333 6003-000333 6003-000333 6006-001095 AA61-00706B AA61-01235A AA65-30105A AA94-11730A 0202-000008 0202-000187 0204-001095 0202-001046 SW811S 3403-001107 MPP+LP 6003-000333 HP+PCB 6003-000333 GTAY01 AA39-20179C AA61-00719B AA97-05539A PCB AA41-00521A EY01 AA60-40011A EY02 AA60-40011A EY03 AA60-40011A EY04 AA60-40011A GTY05 AA60-40014A GTY06 AA60-40014A GTY07 AA60-40014A GTY08 AA60-40014A GTY09 AA60-40014A GTY10 AA60-40014A AA94-11731A LD01 0601-001381 RM01 AA32-00012A CN01 AA39-20069A AA97-12478A DC02 0401-000005 DC01 0401-000005 RY01 2001-000020 RY04 3812-000219 RY03 3812-000219 JC05 3812-000219 JC01 3812-000219 JC03 3812-000219 JC04 3812-000219 PCB AA41-00702A CY01 2401-002291 AA94-12461A JK04 3722-000544 JKH701 3722-001061 JA701 3722-001164 AV+CV 6003-001268 CN704 AA39-00070B CN701 AA39-00317B CN703 AA39-20069A AA63-10002A AA97-12697A DZ701 0403-000720 R702 2001-000028 R701 2001-000028 C701 2202-000121 C702 2202-000121 C708 2202-000231 C707 2202-000231 L701 2701-000114 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW SCREW-ASS'Y TAPT;WP,BH,+,M4,L12,ZPC(YEL) HOLDER-COVER;ALL MODEL,NYLON-66 T1.0 V2, HOLDER-CHASSIS;DP Z7,AA61-01190A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V2, ASSY PCB MISC-MASTER;Z6,Z7Z9,K55A,S57A,P SOLDER-WIRE;S63S-W3.0,S63S,D3,63Sn/37Pb, SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb THINNER;#4520,-,-,FLUX;CF-110VH-2A,-,-,-,SWITCH-PUSH;250V,5A,DPST,-,KDC-A04 SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW LEAD CONNECTOR-ASSY;,3(2)P,YFH800-150,S, HOLDER-MASTER;T6,W3,HIPS V0,BLK,J52A ASSY AUTO-MASTER;WS36Z48D,KS4A,PAL PCB-MASTER S/W;CS32Z4,FR-1,1L,A,1.6T,245 K EYELET;ID2.0,OD2.8,BST K EYELET;ID2.0,OD2.8,BST K EYELET;ID2.0,OD2.8,BST K EYELET;ID2.0,OD2.8,BST PIN-GT,ASSY;AUTO PIN-GT,ASSY;AUTO PIN-GT,ASSY;AUTO PIN-GT,ASSY;AUTO PIN-GT,ASSY;AUTO PIN-GT,ASSY;AUTO ASSY PCB MISC-LED;CS29Z6HPJX/BWT,K55A LED;ROUND,RED/GRN,5.0MM,650/563NM MODULE REMOCON;ORC-50HF2,38KHZ,940NM,MES LEAD CONNECTOR-ASSY;,5P,YBNH025-05,67096 ASSY AUTO-LED;CS29Z6,K55A DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, R-CARBON(S);22OHM,5%,1/2W,AA,TP,2.4X6.4M WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) PCB-LED;WS32Z6HF,FR-1,1L,A,1.6T,245X245, C-AL;47uF,20%,16V,GP,TP,6.3x5,5 ASSY PCB MISC-A/V;29Z6,K55A,ALL,SEH,0062 JACK-VHS;4P,11.5mm,AG,BLK,N JACK-PHONE;1P,3.6PI,AG,BLK,N JACK-PIN;3P,3.4mm,SN,WH:YE:RE,#16-22 SCREW-TAPTITE;TH,+,B,M4.0,L12.0,ZPC(YEL) LEAD CONNECTOR-ASSY;,4P,YBNH250-04,35184 LEAD CONNECTOR ASSY;K55A/WT-32Z4HD,UL100 LEAD CONNECTOR-ASSY;,5P,YBNH025-05,67096 BAND-TIE;NYLON66 V2,L100,NTR ASSY AUTO--A/V SIDE;,K55A,PAL,29Z6 DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 R-CARBON(S);100OHM,5%,1/2W,AA,TP,2.4X6.4 R-CARBON(S);100OHM,5%,1/2W,AA,TP,2.4X6.4 C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm
4 4 4 4 4 4 4 4 3 4 5 5 5 4 2 3 3 3 3 3 3 3 3 3 ! 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 4 5 5 5 5 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6
L702 L706 L705 L708 L707 J701 J703 PCB
2701-000114 2701-000168 2701-000168 3301-000287 3301-000287 3812-000219 3812-000219 AA41-00620B AA96-01269A AA63-00571A HA83-00006A HA83-00012A AA81-00105A AA64-02667B AA94-12341A Q402 0505-001116 C806 2306-000112 C820 2401-003419 RL801S 3501-001053 CN702 3711-003974 JA702 3722-001767 JA701 3722-001884 HIC401 AA13-00094A C-BLOC AA26-00069A T801S AA26-00178A T444S AA26-00170A T401 AA26-50001S LR404S AA27-40001S PFC01S AA27-00269A LR402S AA27-10004F LR403S AA27-00070A CN702A AA39-00114C GT804S AA39-20010C BOT AA39-20536G CABLE AA39-30007B TU02S AA40-00051A AA61-00707B AA95-03091A BOT1 0403-000508 EX01 2801-004019 DX01 2802-001177 CN02 3711-003495 CN01 3711-003495 CN03 3711-003601 BR02 AA61-10068A BR01 AA61-10068A AA97-13360A IC06 1203-002000 DC51 2301-000224 DC41 2309-000138 EC48 2401-002463 EC49 2401-002463 AA97-12148A DD16 0401-000133 DD15 0401-000133 DD14 0401-000133 DD17 0401-000133 DD18 0401-000133 DD19 0401-000133 DD01 0401-000133 DD02 0401-000133 DD08 0401-000133 DD09 0401-000133 DD10 0401-000133 DD13 0401-000133 DD20 0403-000620 DD11 0403-000746
INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) WIRE-NO SHEATH CU;TCWA,300V,52mm(TAPING) PCB-A/V SIDE(Z7);CT-29Z7HR,FR-1,1L,B,1.6 ASSY COVER P-AV;29Z6 COVER-A/V;29Z6,HIPS,HB,G4309,DGN-1189 LP-RESIN HIPS;,BASF495F,NTR,HB LP-RESIN;,M BATCH,WILSON 6053-GY-60,GRY A/S-MARKING PAINT;,DGN-118G,WARM GREY,SO INLAY-AV;Z7,PS SHEET,T0.3,DGN-K189,K55A ASSY PCB MAIN;CW29Z68P,29,SEB,707B FET-SILICON;BUZ73A,N,200V,22A,0.6ohm,40W C-FILM,MPPF;100nF,20%,250V,BK,-,15mm C-AL;2200uF,20%,50V,WT,TP,16X35.5mm RELAY-POWER;5Vdc,530mW,10A,1FormA,15mS,5 CONNECTOR-HEADER;BOX,12P,1R,2.5mm,STRAIG JACK-PIN;2P(9P),-,NI,WHI/RED,JACK-SCART;42P,-,SNPB,BLK,IC HYBRID;-,DDRI001A,SIP,5P,-,TP TRANS FBT;FUJ-29C002C(S),DREAM3,4,-,-,-, TRANS SWITCHING;EER5345,K55A,PAL,CIS,160 TRANS FBT;FUJ-29H002F,29F,1.95MH,FERRIT TRANS-HORIZ.DRIVE;-,-,-,6.0mH,-,-,44uH,COIL HORIZ. WIDTH;-,110uH,SB-5S8202.6,PI COIL CHOKE-PFC;35MH,CPTTV,35MH,10%,2.0OH COIL CHOKE;-,56uH,K,-,2.5A,BK,-,DR12x15, COIL LINEARITY;-,7uH,YL81 DR1518,11mm,17 LEAD CONNECTOR-ASSY;,-,-,12P,-,-,-,35155 LEAD CONNECTOR-ASSY;,1P,YFH800-01,S,600, LEAD CONNECTOR ASSY;,1P,F,F,60MM,1617#22 IF-CABLE;-,T,150mm,1365#26 TUNER;TCPW3001PC18B(S),TCPW3001PC18B(S), HOLDER-COVER;ALL MODEL,NYLON-66 T1.0 V2, ASSY SUB-PCB,FEATURE BOX;,K55A, ,PAL DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 CRYSTAL-UNIT;20.25MHz,30ppm,28-AAM,13pF, RESONATOR-CERAMIC;2.696MHZ,0.4%,BK,10X4. CONNECTOR-HEADER;NOWALL,34P,2R,2.54MM,AN CONNECTOR-HEADER;NOWALL,34P,2R,2.54MM,AN CONNECTOR-HEADER;BOX,12P,1R,2.5mm,ANGLE, BRACKET-PCB;M2160,SPTE,T0.3,-,-,-,BRACKET-PCB;M2160,SPTE,T0.3,-,-,-,ASSY AUTO-F,BOX;WS32Z6HPGX/BWT,K55A,RUSS IC-VOL. DETECTOR;7027,TO-92,3P,-,PLASTIC C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5 C-FILM,PE-PPF;100nF,5%,50V,TP,20x16x8.5, C-AL;470uF,20%,16V,GP,TP,8x11.5,5 C-AL;470uF,20%,16V,GP,TP,8x11.5,5 ASSY SMD;,K55A PAL DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-SWITCHING;RLS4148,100V,200MA,SOD-8 DIODE-ZENER;RLZ5.6B,5.6,500mW,LL-34,TP DIODE-ZENER;RLZ3.9B,3.9V,3.89-4.16V,400m
Samsung Electronics
7-1
Electrical Parts List
Level Loc. No. Code No.
Description ; Specification
Remark
Level Loc. No. Code No.
Description ; Specification
Remark
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
TD01 DD07 DD06 DD03 DD04 DD05 DQ10 DQ05 DQ04 DQ03 DQ02 DQ11 EQ06 TQ01 TQ02 DQ08 DQ07 DQ06 DQ01 DQ09 EQ04 EQ05 IC11 IC10 IC05 IC01 IC04 DR23 SC29 SC31 SC33 SR30 SR31 SR32 SR33 SR34 DR07 DR68 DR69 DR70 ER31 ER30 ER29 EC07 DR41 DR40 DR51 DR58 DR59 DR60 DR50 DR49 DR42 DR36 DR65 TR11 TR04 TR02 SR35 ER21 ER20 ER04 DR88 DR11 DR10 DR09 DR06 DR05 DR04 DR03 DR02 DR16 DR35 DR30 DR26 DR21
0403-001117 0403-001117 0403-001117 0403-001117 0403-001117 0403-001117 0501-000280 0501-000280 0501-000280 0501-000280 0501-000280 0501-000344 0501-000344 0501-000344 0501-000344 0501-000344 0501-000344 0501-000344 0501-000344 0501-000727 0505-000110 0505-000110 0801-000662 1001-001177 1203-002186 1204-001938 1204-001989 2007-000052 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000070 2007-000072 2007-000072 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074 2007-000074
DIODE-ZENER;RLZ12B,5%,500mW,LL-34,TP DIODE-ZENER;RLZ12B,5%,500mW,LL-34,TP DIODE-ZENER;RLZ12B,5%,500mW,LL-34,TP DIODE-ZENER;RLZ12B,5%,500mW,LL-34,TP DIODE-ZENER;RLZ12B,5%,500mW,LL-34,TP DIODE-ZENER;RLZ12B,5%,500mW,LL-34,TP TR-SMALL SIGNAL;KSA1182,PNP,-35V,-30V,-5 TR-SMALL SIGNAL;KSA1182,PNP,-35V,-30V,-5 TR-SMALL SIGNAL;KSA1182,PNP,-35V,-30V,-5 TR-SMALL SIGNAL;KSA1182,PNP,-35V,-30V,-5 TR-SMALL SIGNAL;KSA1182,PNP,-35V,-30V,-5 TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;KSC1623,NPN,60V,50V,100m TR-SMALL SIGNAL;BC848C,NPN,310mW,SOT-23, FET-SILICON;2N7002,N,60V,115mA,7.5ohm,2 FET-SILICON;2N7002,N,60V,115mA,7.5ohm,2 IC-CMOS LOGIC;74HC123,MULTIVIBATOR,SOP,1 IC-VIDEO SWITCH;TEA6425D,VIDEO SWITCH ,S IC-POSI.FIXED REG.;18,DPAK,3P,240MIL,PLA IC-DECODER;VSP9407B-B11,MQFP,80P,14X14MM IC-VIDEO PROCESS;CXA2165Q,QFP,64P,20X14M R-CHIP;10Kohm,1%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;0ohm,5%,1/16W,DA,TP,1608 R-CHIP;47ohm,5%,1/16W,DA,TP,1608 R-CHIP;47ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
DR17 DR18 DR19 DR20 SR37 DR25 TR09 TR07 DR46 DR45 DR44 DR43 DR87 DR86 DR32 ER07 ER06 DR33 DR63 DR37 DR34 DR13 DR14 DR66 ER09 DR80 DR64 DR62 DR61 DR47 DR24 DR82 DR81 DR27 DR28 DR29 DR39 DR38 DR31 DR57 DR56 DR55 DR52 DR53 DR54 SR36 ER36 ER35 ER34 ER33 ER32 DR08 DR15 ER26 ER28 SR09 SR10 TR01 TR03 TR05 TR08 TR10 ER25 EC28 EC58 ER01 ER02 ER13 ER24 ER22 ER19 ER16 EC37 EC38 EC39 EC40
2007-000074 2007-000074 2007-000074 2007-000074 2007-000077 2007-000077 2007-000078 2007-000078 2007-000078 2007-000078 2007-000078 2007-000078 2007-000080 2007-000080 2007-000081 2007-000082 2007-000082 2007-000082 2007-000084 2007-000084 2007-000084 2007-000086 2007-000086 2007-000088 2007-000090 2007-000090 2007-000090 2007-000090 2007-000090 2007-000090 2007-000092 2007-000094 2007-000097 2007-000107 2007-000107 2007-000118 2007-000124 2007-000124 2007-000124 2007-000211 2007-000211 2007-000211 2007-000211 2007-000211 2007-000211 2007-000259 2007-000293 2007-000293 2007-000293 2007-000293 2007-000293 2007-000691 2007-000869 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2007-001167 2203-000181 2203-000181 2203-000181 2203-000181
R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/16W,DA,TP,1608 R-CHIP;470ohm,5%,1/16W,DA,TP,1608 R-CHIP;470ohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;3.3Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,5%,1/16W,DA,TP,1608 R-CHIP;5.6Kohm,5%,1/16W,DA,TP,1608 R-CHIP;5.6Kohm,5%,1/16W,DA,TP,1608 R-CHIP;7.5Kohm,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;10KOHM,5%,1/16W,DA,TP,1608 R-CHIP;15Kohm,5%,1/16W,DA,TP,1608 R-CHIP;22Kohm,5%,1/16W,DA,TP,1608 R-CHIP;47Kohm,5%,1/16W,DA,TP,1608 R-CHIP;470Kohm,5%,1/16W,DA,TP,1608 R-CHIP;470Kohm,5%,1/16W,DA,TP,1608 R-CHIP;390ohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;2.2Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.1Kohm,5%,1/16W,DA,TP,1608 R-CHIP;1.6Kohm,5%,1/16W,DA,TP,1608 R-CHIP;100ohm,5%,1/8W,DA,TP,3216 R-CHIP;100ohm,5%,1/8W,DA,TP,3216 R-CHIP;100ohm,5%,1/8W,DA,TP,3216 R-CHIP;100ohm,5%,1/8W,DA,TP,3216 R-CHIP;100ohm,5%,1/8W,DA,TP,3216 R-CHIP;3.3Mohm,5%,1/16W,DA,TP,1608 R-CHIP;4.7Kohm,1%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 R-CHIP;75ohm,5%,1/16W,DA,TP,1608 C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP,
7-2
Samsung Electronics
Electrical Parts List
Level Loc. No. Code No.
Description ; Specification
Remark
Level Loc. No. Code No.
Description ; Specification
Remark
6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6
EC41 EC36 EC12 EC16 EC24 EC32 EC33 EC43 EC56 EC60 SC44 SC49 TC08 EC55 EC45 EC46 EC52 EC53 EC54 EC11 DC16 DC17 DC18 DC19 DC21 DC15 DC03 DC05 DC10 DC11 DC14 DC25 DC44 EC01 EC02 EC03 EC04 DC38 DC26 DC27 DC28 DC29 DC37 DC36 DC40 DC02 DC01 SC48 SC47 DC07 EC10 EC13 EC14 EC15 DC32 DC45 EC08 EC09 EC35 EC34 EC65 EC64 EC63 EC62 EC31 EC30 EC29 DC34 EC23 EC22 EC21 EC20 DC35 EC17 EC18 EC19 TC02
2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000181 2203-000257 2203-000440 2203-000440 2203-000440 2203-000491 2203-000491 2203-000491 2203-000575 2203-000575 2203-000575 2203-000575 2203-000575 2203-000575 2203-000575 2203-000575 2203-000626 2203-000626 2203-000681 2203-000681 2203-000681 2203-000681 2203-000681 2203-000681 2203-000681 2203-000896 2203-000975 2203-000975 2203-000975 2203-000975 2203-000975 2203-000975 2203-000975 2203-000975 2203-002494
C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100nF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;100