Text preview for : CSDTD 51.PDF part of Aiwa CSD-TD51, CSD-TD52, CSD-TD53 Service Manual Cd Fm Tape Recorder - Tape mech. TN-21ZVC-2000, Cd mech. DA11T3C - (3.972Kb) 2 Part File - pag. 30
Back to : cd_fm_tape_rec.part1.rar | Home
CSD-TD51 U(S),K(S),EZ(S) CSD-TD52 U(W) CSD-TD53 U(L)
SERVICE MANUAL
COMPACT DISC RADIO CASSETTE RECORDER · BASIC TAPE MECHANISM : TN-21ZVC-2000 · BASIC CD MECHANISM : DA11T3C
This Service Manual is the "Revision Publishing" and replaces "Simple Manual" CSD-TD51 U(S)/TD52 U(W)/TD53 U(L)(S/M Code No. 09-003-343-3T1) CSD-TD51 EZ(S),K(S)(S/M Code No. 09-003-343-3T2).
RE
S/M Code No. 09-003-343-3R1
VI
DA TA
SIO
N
SPECIFICATIONS U MODEL EZ MODEL
·
Design and specifications are subject to change without notice .
·
Design and specifications are subject to change without notice .
K MODEL
·
Design and specifications are subject to change without notice .
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling. Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block (SF-P101NR)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure. PICK UP ASSY SF-P101NR
1 16
Solder
TO/FROM CD C.B
3
ELECTRICAL MAIN PARTS LIST
REF. NO IC
PART NO.
KANRI NO.
DESCRIPTION
REF. NO C317 C801 C805 C806 C807 C808 C809 C810 C811 C812 C816 C817 C821 C822 C823 C824 C829 C830 C833 C834 C835 C836 C843 C844 C845 C846 C851 C852 C853 CN201 CN801 CNA302 CNA801 L801 SW801 CD C.B
87-A21-550-010 87-A21-185-040 87-A21-064-010 87-A21-520-040 87-A20-446-010 87-A20-459-010 87-A21-093-010 8A-CH4-661-010 87-A21-431-010 TRANSISTOR 89-327-143-080 87-026-447-080 89-111-624-080 87-026-213-080 89-503-025-010 89-320-011-080 87-026-230-080 89-327-125-080 89-112-965-080 87-026-463-080 87-026-291-080 89-213-702-080 87-026-462-080 89-318-154-080 89-109-332-380 89-113-187-080 87-026-295-080 87-026-237-080 87-026-239-080 87-026-464-080 DIODE 87-070-345-080 87-A40-616-070 87-A40-128-080 87-017-072-080 87-027-399-080 87-027-607-080 87-A40-648-080 87-017-978-080 87-020-465-080 87-027-702-080 87-A40-465-010 MAIN C.B C211 C212 C215 C216 C231 C232 C233 C234 C235 C236 C237 C239 C240 C247 C248 C310 C316 87-A11-603-080 87-A11-603-080 87-016-460-080 87-016-460-080 87-010-213-080 87-010-213-080 87-A10-201-080 87-A10-201-080 87-016-669-080 87-016-669-080 87-010-371-080 87-010-197-080 87-010-197-080 87-010-401-080 87-010-401-080 87-010-248-080 87-010-263-080
IC,TA2149N C-IC,LC72121M IC,LA4227 C-IC,M61509FP C-IC,LA9241ML C-IC,LC78622ED IC,LA6541D C-IC,LC867132V-5P07 IC,BA4560N
KANRI DESCRIPTION NO. 87-010-197-080 CAP, CHIP 0.01 DM 87-010-248-080 CAP, ELECT 220-10V 87-012-365-080 C-CAP,S 0.027-25VBK 87-012-365-080 C-CAP,S 0.027-25VBK 87-010-405-080 CAP, ELECT 10-50V 87-010-405-080 87-010-401-080 87-010-401-080 87-010-178-080 87-010-178-080 87-010-180-080 87-010-180-080 87-010-401-080 87-010-401-080 87-010-178-080 87-010-178-080 87-010-178-080 87-010-178-080 87-018-195-080 87-010-248-080 87-010-322-080 87-010-322-080 87-010-197-080 87-018-124-080 87-010-178-080 87-010-263-080 87-010-186-080 87-010-178-080 87-018-211-080 87-099-018-010 87-A60-110-010 8A-CD9-629-010 8A-CD9-630-010 87-007-342-010 8Z-CD9-609-010 CAP, CAP, CAP, CHIP CHIP ELECT 10-50V ELECT 1-50V ELECT 1-50V CAP 1000P CAP 1000P
PART NO.
TR,2SC2714 (0.1W) TR,2SC1740S R TR,2SA1162Y CHIP-TR,DTC114YK C-FET,2SK302GR<51 K,51 EZ> TR,2SC2001 (15W)<51 K,51 EZ> CHIP-TR,DTA114YK<51 K,51 EZ> CHIP TR,2SC2712GR TR,2SA1296 (0.75W) TR,2SA933S (0.3W) TR,DTC124XS TR,2SB1370E TR,2SC1740 S(RS 0.3W) TR,2SC1815 (0.4W) TR,2SA933RS TR,2SA1318TU TR,DTC144TK CHIP-TR,DTC124XK TR,DTC114TK (0.2W) TR,DTC114TS (0.3W)
C-CER 1500P C-CER 1500P CAP, ELECT 1-50V CAP, ELECT 1-50V CHIP CAP 1000P CHIP CHIP CHIP CAP, CAP, CAP 1000P CAP 1000P CAP 1000P CER 1200P-16V ELECT 220-10V
C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH CAP, CHIP 0.01 DM CAP, CER 270P-50V CHIP CAP 1000P CAP, ELECT 100-10V CAP,CHIP 4700P CHIP CAP 1000P CAP, CER 0.01-50 CONN,16P CONN,4P V S2M-4W CONN ASSY,6P MA-TU CONN ASSY, 4P RPH COIL,OSC 85K BIAS SW,SL 1-6-2 PS62D01
DIODE,IN4148 VARI-CAP,SVC384(S/T) C-VARI-CAP,HVU202A ZENER,HZS3B1 ZENER,HZ7A3L (200MA)<51 U,53 U,52 U> ZENER,HZ7B3L<51 K,51 EZ> ZENER,MTZJ8.2A DIODE,1N4003 DIODE,1SS133 (110MA) DIODE,ZENER HZ6C2L (200MA) DIODE,FR202
C30 C251 C261 C262 C263 C264 C265 C266 C267 C268 C271 C272 C278 C279 C301 C306 C307 C308 C311 C312 C321 C322 C325 C401 C402 C403 C404 C405 C406 C407 C408 C409
87-010-260-080 87-010-404-080 87-010-402-080 87-010-402-080 87-010-178-080 87-010-178-080 87-010-263-080 87-010-263-080 87-010-112-080 87-010-112-080 87-010-237-080 87-010-237-080 87-010-405-080 87-010-385-080 87-016-495-000 87-010-404-080 87-010-401-080 87-010-221-080 87-010-263-080 87-010-385-080 87-010-197-080 87-010-263-080 87-010-405-080 87-010-403-080 87-010-197-080 87-010-263-080 87-010-248-080 87-010-197-080 87-010-374-080 87-010-178-080 87-010-198-080 87-010-248-080
CAP, CAP, CAP, CAP, CHIP CHIP CAP, CAP, CAP, CAP,
ELECT 47-25V ELECT 4.7-50V ELECT 2.2-50V ELECT 2.2-50V CAP 1000P CAP 1000P ELECT 100-10V ELECT 100-10V ELECT 100-16V ELECT 100-16V
CAP, ELECT 1000-16V CAP, ELECT 1000-16V CAP, ELECT 10-50V CAP, ELECT 220-25V CAP,E 3300-25 M SMG CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CHIP ELECT ELECT ELECT ELECT ELECT 4.7-50V 1-50V 470-10V 10-10V 220-25V
CAP, S 0.05-16 CAP, S 0.15-16 C-CAP,S 0.22-16 B C-CAP,S 0.22-16 B C-CAP,S 0.015-50 B C-CAP,S 0.015-50 B C-CAP,S0.33-16 KB C-CAP,S0.33-16 KB C-CAP,S 0.1-25 K B C-CAP,S 0.1-25 K B CAP, CAP, CAP, CAP, CAP, ELECT 470-50V CHIP 0.01 DM CHIP 0.01 DM ELECT 1-50V ELECT 1-50V
CHIP 0.01 DM ELECT 100-10V ELECT 10-50V ELECT 3.3-50V CHIP 0.01 DM ELECT 100-10V ELECT 220-10V CHIP 0.01 DM ELECT 47-10V CAP 1000P
CAP, ELECT 220-10V CAP,E 100-10
CAP, CHIP 0.022 CAP, ELECT 220-10V
4
REF. NO C410 C411 C412 C413 C414 C416 C417 C418 C419 C420 C421 C422 C423 C424 C425 C426 C428 C429 C430 C431 C432 C433 C434 C435 C436 C437 C438 C439 C440 C441 C442 C445 C446 C447 C448 C450 C451 C455 C457 C458 C459 C460 C461 C462 C463 C465 C466 C467 C469 C470 C471 C472 C473 C474 C475 C476 C477 C478 C479 C480 C481 C482 C489 C490 C491 C492 C494 C495 C501 C502
KANRI DESCRIPTION NO. 87-010-263-080 CAP, ELECT 100-10V 87-A11-177-080 C-CAP,S 0.15-16 K B 87-010-401-080 CAP, ELECT 1-50V 87-016-369-080 C-CAP,S 0.033-25 B K 87-010-405-080 CAP, ELECT 10-50V 87-010-545-080 87-012-157-080 87-010-213-080 87-A11-608-080 87-016-369-080 87-A11-177-080 87-010-183-080 87-010-956-080 87-010-993-080 87-010-176-080 87-A11-608-080 87-010-197-080 87-010-186-080 87-012-156-080 87-010-545-080 87-010-374-080 87-010-401-080 87-010-184-080 87-010-197-080 87-010-374-080 87-010-404-080 87-016-669-080 87-010-178-080 87-010-145-080 87-010-197-080 87-010-312-080 87-012-368-080 87-012-368-080 87-012-368-080 87-010-315-080 87-012-140-080 87-012-156-080 87-010-247-080 87-010-312-080 87-010-312-080 87-010-263-080 87-015-819-080 87-010-197-080 87-010-248-080 87-010-197-080 87-010-404-080 87-012-368-080 87-010-263-080 87-012-154-080 87-010-544-080 87-015-785-080 87-015-785-080 87-015-785-080 87-015-785-080 87-010-197-080 87-010-236-080 87-010-197-080 87-010-263-080 87-010-197-080 87-010-221-080 87-010-405-080 87-010-405-080 87-012-368-080 87-012-368-080 87-010-197-080 87-010-221-080 87-010-197-080 87-016-669-080 87-012-368-080 87-010-322-080 CAP, ELECT 0.22-50V C-CAP,S 330P-50 CH C-CAP,S 0.015-50 B C-CAP,S 0.33-25 K B C-CAP,S 0.033-25 B K C-CAP,S 0.15-16 K B C-CAP,S 2700P-50 B CHIP-CAP,S 0.068-25B C-CAP,S 0.056-25 B C-CAP,S 680P-50 SL C-CAP,S 0.33-25 K B CAP, CHIP 0.01 DM CAP,CHIP 4700P C-CAP,S 220P-50 CH CAP, ELECT 0.22-50V CAP, CAP, CHIP CAP, CAP, ELECT 47-10V ELECT 1-50V CAPACITOR 3300P(K) CHIP 0.01 DM ELECT 47-10V
PART NO.
REF. NO C503 C504 C505 C506 C510 C831 CN202 CN205 CN301 CN401 CN403 CN802 CNA205 CNA402 CNA802 L401 L404 SFR430 SW205 X401 FRONT C.B C601 C602 C603 C604 C605 C607 C608 C610 C611 C612 C613 C614 C615 C616 C620 C625 C627 C629 C630 C631 C632 C633 C635 C636 C637 C638 C639 C640 C641 C642 C643 C644 C645 C646 C647 C648 C649 C650 C651 C652 C653 C654 C655 C656 C657 C658 CN601
KANRI NO. 87-010-322-080 C-CAP,S 87-010-322-080 C-CAP,S 87-010-322-080 C-CAP,S 87-010-322-080 C-CAP,S 87-016-669-080 C-CAP,S 87-010-198-080 8A-CH4-689-010 87-A60-109-010 8A-CH4-689-010 87-A60-424-010 87-099-201-010 8A-CH4-687-010 8A-CD9-631-010 8A-CD9-625-010 8A-CD9-631-010 87-003-102-080 87-003-152-080 87-024-437-080 87-036-389-010 8Z-CD5-633-010
PART NO.
DESCRIPTION 100P-50 CH 100P-50 CH 100P-50 CH 100P-50 CH 0.1-25 K B
CAP, CHIP 0.022 CONN,3P V 2.5 CONN,2P V S2M-2W CONN,3P V 2.5 CONN,16P V TOC-B CONN,8P 6216 H CONN,4P V 2.5 CONN ASSY, 2P DOOR CONN ASSY,6P CD-ME CONN ASSY, 4P TP-ME COIL, 10UH COIL, 100UH SFR100K,RH063EC SW, PUSH 1-1-1 R8120125 VIB, CER16.93MHZ FCR16.93M2
CAP, ELECT 4.7-50V C-CAP,S 0.1-25 K B CHIP CAP 1000P C-CAP, S 1P-50 C CH CAP, CHIP 0.01 DM C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 15P-50 0.1-50 0.1-50 0.1-50 27P-50 CH F F F CH
87-010-313-080 87-010-315-080 87-010-319-080 87-010-312-080 87-010-317-080 87-010-196-080 87-010-196-080 87-010-555-040 87-010-196-080 87-A10-189-040 87-010-495-040 87-010-196-080 87-010-493-040 87-010-494-040 87-015-785-080 87-A12-317-080 87-010-196-080 87-A12-317-080 87-A12-317-080 87-A12-317-080 87-A12-317-080 87-A12-317-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-012-195-080 87-A12-317-080 87-099-033-010
CAP, CHIP 18P C-CAP,S 27P-50 C-CAP,S 56P-50 C-CAP,S 15P-50 C-CAP,S 39P-50
CH CH CH CH
CHIP CAPACITOR,0.1-25 CHIP CAPACITOR,0.1-25 CAP,E 100-10 GAS CHIP CAPACITOR,0.1-25 CAP,E 220-10 CAP,E 2.2-50 GAS CHIP CAPACITOR,0.1-25 CAP,E 0.47-50 GAS CAP,E 1-50 GAS CHIP CAPACITOR, 0.1FZ-25Z C-CAP,U 0.1-50 Z F CHIP CAPACITOR,0.1-25 C-CAP,U 0.1-50 Z F C-CAP,U 0.1-50 Z F C-CAP,U 0.1-50 Z F C-CAP,U C-CAP,U C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 0.1-50 Z F 0.1-50 Z F 100P-50 J CH 100P-50 J CH 100P-50 J CH 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 100P-50 J J J J J J J J J J J J J J J J J J J J CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH
CAP 470P C-CAP,S 220P-50 CH CAP, ELECT 100-50V C-CAP,S 15P-50 CH C-CAP,S 15P-50 CH CAP, ELECT 100-10V CAPACITOR,0.01 CAP, CHIP 0.01 DM CAP, ELECT 220-10V CAP, CHIP 0.01 DM CAP, ELECT 4.7-50V C-CAP,S 0.1-50 F CAP, ELECT 100-10V C-CAP,S 150P-50 CH CAP, ELECT 0.1-50V CHIP CHIP CHIP CHIP CAP, CAPACITOR, 0.1FZ-25Z CAPACITOR, 0.1FZ-25Z CAPACITOR, 0.1FZ-25Z CAPACITOR, 0.1FZ-25Z CHIP 0.01 DM
CAP,E 1000-10 SME CAP, CHIP 0.01 DM CAP, ELECT 100-10V CAP, CHIP 0.01 DM CAP, ELECT 470-10V CAP, ELECT 10-50V CAP, ELECT 10-50V C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F CAP, CHIP 0.01 DM CAP, ELECT 470-10V CAP, CHIP 0.01 DM C-CAP,S 0.1-25 K B C-CAP,S 0.1-50 F C-CAP,S 100P-50 CH
C-CAP,U 0.1-50 Z F CONN,16P 6216 H
5
REF. NO CN602 CNA603 CNA604 L601 LCD601 LED602 LED603 LED604 LED606 LED607 LED608 LED610 S601 S604 S605 S606 S607 S611 S613 S614 S615 X601 X602 TUNER C.B C1 C2 C3 C5 C6 C7 C8 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C27 C28 C29 C30 C30 C31 C31 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42
KANRI DESCRIPTION NO. 87-099-201-010 CONN,8P 6216 H 8A-CD9-624-010 CONN ASSY,4P TU-FR 8A-CD9-623-010 CONN ASSY,4P KEY 87-003-102-080 COIL, 10UH 8Z-CH4-635-010 LCD,HLC7365 ZCH-4 88-CD6-630-010 88-CD6-630-010 88-CD6-630-010 88-CD6-630-010 88-CD6-630-010 88-CD6-630-010 88-CD6-631-010 87-A90-164-080 87-A90-164-080 87-A90-164-080 87-A91-704-080 87-A91-704-080 87-A90-164-080 87-A90-164-080 87-A91-704-080 87-A91-704-080 87-030-273-010 87-030-376-080 LED,934ID LED,934ID LED,934ID LED,934ID LED,934ID RED RED RED RED RED
PART NO.
REF. NO C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C71 C72 C73 C75 C91 C92 C93 CF1 CF2 CF3 CN2 CN3 CN605 HD1 HD2 L2 L3 L3 L4 L5 L6 L7 L8 L51 LED601 LED609 TC1 TC51 X1 H.P. CB CN101 CN102 HP1 BATT1 C.B C901 C902 C903 C904 CNA901 !PR901 SP901 SP902 BATT2 C.B SP903 SP904
KANRI DESCRIPTION NO. 87-012-349-080 C-CAP,S 1000P-50 CH 87-010-311-080 CAP 12P 87-010-312-080 C-CAP,S 15P-50 CH 87-010-197-080 CAP, CHIP 0.01 DM 87-010-197-080 CAP, CHIP 0.01 DM 87-010-197-080 87-012-140-080 87-010-197-080 87-010-316-080 87-010-197-080 87-010-197-080 87-014-055-080 87-010-197-080 87-010-197-080 87-010-263-080 87-010-197-080 87-010-197-080 87-012-140-080 87-010-197-080 87-010-197-080 87-A91-094-010 87-008-261-010 87-008-261-010 87-099-854-010 87-A60-110-010 87-A60-113-010 88-CD6-661-010 88-CD6-661-010 87-A50-560-010 8A-CH4-670-010 8A-CH4-671-010 87-A50-420-010 87-A50-566-010 87-A50-567-010 87-A91-308-010 87-005-849-080 87-A50-421-010 88-CD6-630-010 88-CD6-630-010 87-011-254-080 87-A91-659-010 87-A70-061-010 CAP, CHIP 0.01 CAP 470P CAP, CHIP 0.01 C-CAP,S 33P-50 CAP, CHIP 0.01 DM DM CH DM
PART NO.
LED,934ID RED LED,934GD GRN SW,TACT SKQAB(N) SW,TACT SKQAB(N) SW,TACT SKQAB(N) SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT EVQ 214 05R EVQ 214 05R SKQAB(N) SKQAB(N) EVQ 214 05R
CAP, CHIP 0.01 DM CAP,PP 820P-100 J<51 K,51 EZ> CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, ELECT 100-10V CAP, CHIP CAP, CHIP CAP 470P CAP, CHIP CAP, CHIP 0.01 DM 0.01 DM 0.01 DM 0.01 DM
SW,TACT EVQ 214 05R VIB,XTAL 32.768K5PPM VIB,CER CSA5.76MG200
FLTR,CDA10.7 MG80A FILTER, SFE10.7MA5-A FILTER, SFE10.7MA5-A CONN,6P S2M-6W CONN,4P V S2M-4W CONN,2P H S2M-2WR HLDR,BAR ANT. HLDR,BAR ANT. COIL,FM BPF(ACD) BAR-ANT,MW 2B-ACH(COI)<51 U,53 U,52 U> BAR-ANT,MW/LW 3B-ACH(COI)<51 K,51 EZ> COIL,MW OSC(SYN) COIL,FM RF EX(ACH) COIL,FM OSC(ACH) FLTR,PCFAZH- 450T (TOK) COIL,10UH(CECS) COIL,LW OSC(SYN)<51 K,51 EZ> LED,934ID RED LED,934ID RED TRIMER,20P LAR TRIMMER,50P 4.0X4.5 ECRL<51 K,51 EZ> VIB,XTAL 4.500MHZ CSA-309
87-010-314-080 87-010-316-080 87-010-314-080 87-A11-067-080 87-010-313-080 87-014-049-080 87-012-349-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-150-080 87-010-303-080 87-012-349-080 87-010-374-080 87-010-198-080 87-015-835-080 87-010-263-080 87-010-404-080 87-010-197-080 87-010-197-080 87-010-197-080 87-015-770-080 87-016-460-080 87-A11-067-080 87-016-669-080 87-016-669-080 87-010-213-080 87-010-198-080 87-010-213-080 87-010-198-080 87-012-358-080 87-012-358-080 87-015-819-080 87-010-263-080 87-010-197-080 87-010-374-080 87-010-404-080 87-010-197-080 87-012-349-080 87-012-349-080
C-CAP,S 22P-50V C-CAP,S 33P-50 CH C-CAP,S 22P-50V C-CAP,S 1-10 K B CAP, CHIP 18P<51 U,53 U,52 U> CAP,PP 470P-100 J C-CAP,S 1000P-50 CH CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CAP,S 6P-50 CH C-CAP,S 330P-50CH C-CAP,S 1000P-50 CH CAP, ELECT 47-10V CAP, CHIP 0.022 C-CAP,0.047 D CAP, ELECT 100-10V CAP, ELECT 4.7-50V CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CHIP,330P(SL)K C-CAP,S 0.22-16 B C-CAP,S 1-10 K B C-CAP,S 0.1-25 K B C-CAP,S 0.1-25 K B C-CAP,S 0.015-50 B<51 K,51 EZ> CAP, CHIP 0.022<51 U,53 U,52 U> C-CAP,S 0.015-50 B<51 K,51 EZ> CAP, CHIP 0.022<51 U,53 U,52 U> C-CAP,S 0.47-10 F Z C-CAP,S 0.47-10 F Z CAPACITOR,0.01 CAP, ELECT 100-10V CAP, CHIP 0.01 DM CAP, ELECT 47-10V CAP, ELECT 4.7-50V CAP, CHIP 0.01 DM C-CAP,S 1000P-50 CH C-CAP,S 1000P-50 CH
8A-CD9-628-010 87-A60-685-010 87-A60-569-010
CONN ASSY,3P MA-HP CONN,4P H WHT EH JACK,HTJ-035-18
87-010-192-080 87-010-192-080 87-010-192-080 87-010-192-080 8A-CD9-627-010 87-A90-092-080 87-CD6-213-010 87-CD6-213-010
C-CAP,S 0.022-50 C-CAP,S 0.022-50 C-CAP,S 0.022-50 C-CAP,S 0.022-50 CONN ASSY,3P PWR
F F F F
PROTECTOR,2.5A 491<51 K,51 EZ> SPR-C,BATT (-) SPR-C,BATT (-)
87-CD6-213-010 87-CD6-213-010
SPR-C,BATT (-) SPR-C,BATT (-)
6
LCD DISPLAY
REF. NO MOTOR C.B M2 PIN3 SW1 KEY C.B S608 S609 S610
PART NO.
KANRI NO.
DESCRIPTION
9X-262-576-910 91-564-722-110 91-572-085-120
MOTOR GEAR ASSY CONNECTOR 6P LEAF SW
87-A91-704-080 87-A90-164-080 87-A90-164-080
SW,TACT EVQ 214 05R SW,TACT SKQAB(N) SW,TACT SKQAB(N)
· Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Resistor Code Value of resistor Chip resistor
Dimensions (mm)
Figure
Wattage 1/16W 1/16W 1/10W 1/8W
Type 1005 1608 2125 3216
Tolerance 5% 5% 5% 5%
Symbol CJ CJ CJ CJ
Form
L W
L 1.0
t
W 0.5 0.8 1.25 1.6
t 0.35 0.45 0.45 0.55
:A Resistor Code : A
104 108 118 128
1.6 2 3.2
TRANSISTOR ILLUSTRATION
ECB
ECB
ECB
ECB
2SA1296
2SC1815 2SC2001
2SA1318 2SA933 2SC1740 DTC114TS DTC124XS
C B E D G
S
BCE
2SA1162 2SC2712 2SC2714 DTA114YK DTC114TK DTC114YK DTC124XK DTC144TK
2SK302
2SB1370
7
8
WIRING-1 (MAIN/CD)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
J
K 9 10
SCHEMATIC DIAGRAM-1 (MAIN)
NM : NO MOUNTED
11
12
SCHEMATIC DIAGRAM-2 (CD)
13
14
WIRING-2 (MOTOR)
1 2 3 4 5 6 7
IC BLOCK DIAGRAM IC, LC7212M
IC, LA6541D
A
B
H MOTOR C.B
C
M2
IC, TA2149N
+
D
M2 (SLED MOTOR) SW1 (INSIDE LIMIT SW) M3 (SPINDLE MOTOR)
IC, M61509FP
_
E
TO B CD C.B CNA402
mono. SW
F
PIN3
SW1 _ +
G
M3
H
Control logic
IC, BA4560N
I
J
K 15 16
WIRING-3 (FRONT/HP/BATT1/BATT2/KEY)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
F BATT1 C.B E HP C.B
(INSERTED PARTS)
B
SPEAKER L R
(INSERTED PARTS)
B A
G BATT2 C.B
4
1
EZ,K MODEL
U MODEL SP902 SP901 SP904 SP903
C
HP1 PHONES
DRY BATTERY R14x8 DC 12V
3
1 TO B CD C.B CN301
D
TO B CD C.B CN202
J1 AC PT901 B
A
TO A MAIN C.B CN201 TO B CD C.B (2/2) CN403
AC DC U:AC 120V 60Hz EZ,K:AC 230V 50Hz
E
C FRONT C.B
15 16 1 7 2 8 1 2
C FRONT C.B
(CHIP PARTS)
(INSERTED PARTS)
I KEY C.B
(INSERTED PARTS)
F
S613 3 MODE EQUALIZER
TO D TUNER C.B CN003
I KEY C.B
(CHIP PARTS)
S609 BAND RADIO S608 CD S610 POWER STANDBY TAPE
G
CNA603
S611 QSOUND
1
4
1 3
P2
NOTE
123
H
S615 EZ,K MODEL U MODEL VOLUME S614 PLAY/PAUSE S601 FM MODE /OSC LED608 STANDBY OPE/BATT LED610 QSOUND P1 1
3
Rxxx
E C B
E C B
1 2 3
I
EXCEPT U LC
S606
S605 SKIP/SEARCH TUNING ROCK POP JAZZ RADIO CD
S607 PLAY/PAUSE/PRESET S604 STOP/MEMORY
J
K 17 18
SCHEMATIC DIAGRAM-3 (FRONT/KEY)
C FRONT C.B
HLC7365 ZCH-4 (DISPLAY)
C657-635 100P
TO B CD C.B (2/2) CN403
S23
S22
S21
S20
L-934ND R637 100K
COM3
R636 1K C631 0.1
C630 0.1 R635 1K C629 0.1
L-934ND
R R
#
R657 1K
# #
O-H.DUBB
L-934ND
R
#
-5907 SYSTEM CONTROL
# # #
L-934ID R638 1K RADIO
R653 100 C632 0.1
TO A MAIN C.B CN201
L604 1µH C634 0.1 50
0.1
O-DUBB LED
R
R639 1K
C633 0.1
L-934ID
R
L605 1µH
L602 4.7µH
R
R654 10
L-934GD
R655 100
Q605-610 LED DRIVER C625 0.1 C627 0.1 R656 10 P1 3 P2 3
STANDBY OPE/BATT
L-934ID
O-QSOUND AC 12V
I KEY C.B
32.768 MHz 5.76 MHz
P2 1
P1 1
TO D TUNER C.B CN003
P1 2
P2 2
L603 1µH
RESET SW
R
R
HOLD
#
FM MODE/OSC
3 MODE EQUALIZER VOLUME VOLUME
1SS133 1SS133
1SS133
1SS133
19
20
SCHEMATIC DIAGRAM-4 (TUNER U)
21
22
WIRING-4 (TUNER: U)
1 2 3 4 5 6 7
A
B
C
D
E
F
G
H
I
J
K 23
WIRING-5 (TUNER: EZ, K)
1 2 3 4 5 6 7
A
B
C
D
E
F
G
H
I
J
K 24
SCHEMATIC DIAGRAM-5 (TUNER EZ/K)
25
26
ELECTRICAL ADJUSTMENT
D TUNER C.B 567
TC001
< TUNER SECTION >
L003 (MW BAR ANT) 1. FM VT Adjustment Settings : · Test point : TP2 (VT) · Adjustment location : L006 Method : Set to FM 108.0MHz and adjust L006 so that the test point voltage becomes 6.0V ± 0.05V. 2. MW VT Adjustment Settings : · Test point : TP2 (VT) · Adjustment location : L004 Method : Set to MW 1000kHz (U), MW 999kHz (EZ,K) and adjust L004 so that the test point voltage becomes 3.75V ± 0.05V. 3. LW VT Adjustment Settings : · Test point : TP2 (VT) · Adjustment location : L051 Method : Set to LW 288kHz and adjust L051 so that the test point voltage becomes 4.5V ± 0.05V. 4. FM Tracking Adjustment L005.........................................................................98.0MHz 5. MW Tracking Adjustment L003...........................................................................600kHz TC001.......................................................................1400kHz 6. MW Tracking Adjustment L003...........................................................................603kHz TC001.......................................................................1404kHz 12. Bias frequncy Adjustment L801..................................................................85kHz±0.5kHz
< CD SECTION >
13. FE Balance Adjustment Settings : · Test point : IC401 PIN58 (VR), IC401 PIN 20 (FE) · Adjustment location : SFR430 Method : Playback the disc and adjust SFR430 so that the test point voltage becomes 0V.
2 1
L006
L004
L051
3
123
TP2(VT)
+
TC051 L005
C039 TP1(DET)
4
16
IC001
1
IC002
21 1
PRACTICAL SERVICE FIGURE
< TUNER SECTION >
< FM SECTION >
Sensitivity: (THD 3%) Signal to Noise Ratio: (Input 60dB) Less than 18dB (87.5MHz) Less than 18dB (98.0MHz) Less than 18dB (108.0MHz) More than 66dB (at 98.0MHz) (EXCEPT U) More than 58dB (at 98.0MHz) (U) Less than 3% (at 98.0MHz) 10.7MHz More than 20dB
L007
89 B CD C.B
Distortion: (Input 60dB) Intermediate frequency: Stereo separation:
IC404 SFR430
#
CN401
7. LW Tracking Adjustment L003...........................................................................153kHz TC051.........................................................................288kHz 8. AM IF Adjustment Settings : · Test point : TP1(DET) · Adjustment location : L007 Method : Adjust L007 so that the output level at 1400kHz becomes maximum. 9. AM IF Adjustment Settings : · Test point : TP1 (DET) · Adjustment location : L007 Method : Adjust L007 so that the output level at 1404kHz becomes maximum.
< AM SECTION >
Sensitivity: (S/N 10dB) Distortion: (Input 74dB) Intermediate frequency: Less than 48dB (at 600kHz) Less than 46dB (at 1000kHz) Less than 44dB (at 1400kHz) Less than 3% 450kHz
< LW SECTION >
Sensitivity: (S/N 10dB) Distortion: (Input 80dB) Intermediate frequency: Less than 60dB (at 153kHz) Less than 56dB (at 198kHz) Less than 52dB (at 288kHz) Less than 3% 450kHz
A MAIN C.B
CN201
IC801 CN801 L801
< DECK SECTION >
10. Tape Speed Adjustment Settings : · Test tape : TTA100 · Test point : J251 (PHONES jack) · Adjustment location : SFR of deck motor Method : Play back the test tape and adjust SFR so that the frequency counter reads 3000Hz ± 30Hz. 11. Head Azimuth Adjustment Settings : · Test tape : TTA320 · Test point : J251 (PHONES jack) · Adjustment location : Azimuth adjustment screw Method : Play back the 8kHz signal of the test tape and adjust screw so that the output becomes maximum.
< CASSETTE SECTION >
Tape speed: Wow & flutter: Take-up torque: FF torque: Rew torque: S/N ratio: Distortion: Noise (PB): Erasing Ratio (W/FILTER): 3000Hz±60Hz Less than 0.3% (JIS RMS) 30-60g-cm (FWD) 55-140g-cm 55-140g-cm More than 35dB Less than 3.0% (PB) Less than 1mV (AC/DC, MIN) More than 45dB
@
CASSETTE DECK MOTOR CASSETTE DECK HEAD
E H.P. C.B
J251 PHONES
0
!
27
0!
28
IC DESCRIPTION IC, LA9241ML
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Pin Name FIN2 FIN1 E F TB TETE TESI SCI TH TA TDTD JP TO FD FDI/O I I I I I I O I I I O I I I O O I Description Pin to which external pickup photo diode is connected. RF signal is created by adding with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal. Pin to which external pickup photo diode is connected. Pin to which external pickup photo diode is connected. TE signal is created by subtracting from the F pin signal. Pin to which external pickup photo diode is connected. DC component of the TE signal is input. Pin to which external resistor setting the TE signal gain is connected between the TE pin. TE signal output pin. TES "Track Error Sense" comparator input pin. TE signal is passed through a bandpass filter then input. Shock detection signal input pin. Tracking gain time constant setting pin. TA amplifier output pin. Pin to which external tracking phase compensation constants are connected between the TD and VR pins. Tracking phase compensation setting pin. Tracking jump signal (kick pulse) amplitude setting pin. Tracking control signal output pin. Focusing control signal output pin. Pin to which external focusing phase compensation constants are connected between the FD and FA pins. 18 FA I Pin to which external focusing phase compensation constants are connected between the FD and FA pins. 19 20 21 22 23 24 25 26 27 28 29 30, 31 32, 33 34 35 FAFE FEAGND SP SPI SPG SPSPD SLEQ SLD SL-, SL+ JP-, JP+ TGL TOFF I O I -- O I I I O I O I I I I Pin to which external focusing phase compensation constants are connected between the FA and FE pins. FE signal output pin. Pin to which external FE signal gain setting resistor is connected between the FE pin. Analog signal GND. Signal ended output of the CV+and CV- pin input signal. Spndle amp input. Pin to which external spindle gain setting resistor in 12 cm mode is connected. Pin to which external spindle phase compensation constants are connected together with SPD pin. Spindle control signal output pin. Pin to which external sled phase compensation constants are connected. Sled control signal output pin. Sled advance signal input pin from microprocessor. Tracking jump signal input pin from DSP. Tracking gain control signal input from DSP. Low gain when TGL = H. Tracking off control signal input pin from DSP. Off when TOFF = H.
29
Pin No. 36 37 38 39, 40 41 42
Pin Name TES HFL SLOF CV, CV+ RFSM RFS-
I/O O O I I O I
Description Pin from which TES signal is output to DSP. "High Frequency Level" is used to judge whether the main beam position is on top of bit or on top of mirror. Sled servo off control input pin. CLV error signal input pin from DSP. RF output pin. RF gain setting and EFM signal 3T compensation constant setting pin together with RFSM pin.
43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
SLC SLI DGND FSC TBC NC DEF CLK CL DAT CE DRF FSS VCC2 REFI VR LF2 PH1 BH1 LDD LDS VCC1
O I -- O I -- O I I I I O I -- -- O I I I O I --
"Slice Level Control" is the output pin which controls the RF signal data slice level by DSP. Input pin which control the data slice level by the DSP. Digital system GND. Output pin to which external focus search smoothing capacitor is connected. "Tracking Balance Control" EF balance variable range setting pin. No connection. Disc defect detector output pin. Reference clock input pin. 4.23 MHz of the DSP is input. Microprocessor command clock input pin. Microprocessor command data input pin. Microprocessor command chip enable input pin. "Detect RF" RF level detector output. "Focus Search Select" focus search mode (± search/+ search) select pin. Servo system and digital system Vcc pin. Pin to which external bypass capacitor for reference voltage is connected. Reference voltage output pin. Disc defect detector time constant setting pin. Pin to which external capacitor for RF signal peak holding is connected. Pin to which external capacitor for RF signal bottom holding is connected. APC circuit output pin. APC circuit input pin. RF system Vcc pin.
30
IC, LC78622ED
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12, 13 14 15 16 17 18 19, 20 21 22 23 24 25 26 27 28 29 30 31 32, 33 34 35 36 37 38 39 40 41 42 Pin Name DEFI TAI PDO VVSS ISET VVDD FR VSS EFMO EFMIN T2 CLV+, CLK___
I/O I I O -- I -- I -- O I I O O I I O O O O O -- O O -- I O O O O I -- O -- O -- -- O -- O R-channel 1-bit DAC. L-channel 1-bit DAC. For PLL.
Description Defect sense signal (DEF) input pin. (Connect to 0V when not used). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. GND pin for built-in VCO. Be sure to connect to 0V. Pin to which external resistor adjusting the PD0 output current. Power supply pin for built-in VCO. Pin for VCO frequency range adjustment. Digital system GND. Be sure to connect to 0V. For slice level control. EFM signal output pin. EFM signal input pin. Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Disc motor control output. Three level output is possible using command. Rough servo or phase control automatic selection monitoring output pin. Rough servo at H. Phase servo at L.
V/P HFL TES TOFF TGL JP+, JPPCK FSEQ VDD SL+ SLCONT3 (NC) PUIN
_______
Track detect signal input pin. Schmidt input. Tracking error signal input pin. Schmidt input. Tracking OFF output pin. Tracking gain selection output pin. Gain boost at L. Track jump control signal output pin. Three level output is possible using command. EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in. Sync signal detection output pin. H when the sync signal which is detected from EFM signal and thesync signal which is internally generated agree. Digital system power supply pin. Moves the sled to outer circumference. Moves the sled to inner circumference. Not connected. CD pickup inner switch detection. Read, wright signal. De-emphasis monitor output pin. De-emphasis disc is being played back at H. C2 flag output pin. DIGITAL OUT output pin. (EIAJ format). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Not used. Set the pin to open. L-channel mute output pin. L-channel power supply pin. L-channel output pin. L-channel GND. Be sure to connect to 0V. R-channel GND. Be sure to connect to 0V. R-channel output pin. R-channel power supply pin. R-channel mute output pin.
RW EMPH C2F DOUT T3, T4 N.C. MUTEL LVDD LCHO LVSS RVSS RCHO RVDD MUTER
31
Pin No. 43 44 45 46 47 48 49 50 51
Pin Name XVDD XOUT XIN XVSS SBSY EFLG PW SFSY SBCK
I/O -- O I -- O O O O I Crystal oscillator power supply pin.
Description
Pin to which external 16.9344 MHz crystal oscillator is connected. Crystal oscillator GND pin. Be sure to connect to 0V. Subcode block sync signal output pin. C1, C2, single and dual correction monitoring pin. Subcode P, Q, R, S, T, U and W output pin. Subcode frame sync signal output pin. Falls down when subcode enters standby. Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not in use.)
52 53 54 55 56 57 58 59 60 61 62 63 64
FSX WRQ RWC SQOUT COIN
___________
O O I O I I I O O O I I I
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of crystal oscillator. Subcode Q output standby output pin. Read/write control input pin. Schmidt input. Subcode Q output pin. Command input pin from microprocessor. Command input read clock or subcode read input clock from SQOUT pin LC78622 reset input pin. Set this pin to L once when the main power is turned on. Test signal output pin. Use this pin as open (normally L output). 16.9344 MHz output pin. 4.2336 MHz output pin. Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V while it is not controlling.
CQCK RES T11 16M 4.2M T5
______
CS T1
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
32
IC, LC867132V-5P07
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37-40 41 42 43, 44 45-50 Pin Name O-RMC/CE O-DATA O-CLK -- O-CLK SFT I-HOLD RST XT1 (IN) XT2 (OUT) VSS1 CF1 (IN) CF2 (OUT) VDD1 I-ST IND I-KEYO I-CD SW I-KEY1 I-MOTOR I-REC I-FM/AM I-TU DO O-BASS LED O-QS LED O-DUBB LED O-INT I-DRF I-WRQ I-REMO S0/PA0 S1/PA1 S2/PA2 S3/PA3 S4/PA4 S5/PA5 S6/PA6 S7/PA7 S8~S11 VDD3 VSS3 S12, S13 S14- S19 I/O O O O -- O I I I O -- I O -- I I I I I I I I O O O O I I I O O O O O O O O O -- -- O O Power supply for microcomputer (+5V). GND. LCD segment output. LCD segment output. Power supply for microcomputer (+5V). FM STEREO status input. KEY AD input. CD DOOR SW status detection input. KEY AD input. DECK MECHA MOTOR status input. REC status input. FM, AM status input. (Not connected) Data input from tuner PLL.(Not connected) BASS LED ON/OFF control output. Q-Sound LED ON/OFF control output. LED control output used for high-speed dubbing. INT DIODE MATRIX detection output.(Not connected) CD RF level detection input. CD sub-code Q standby input. Remote control input. LCD segment output. LCD segment output. LCD segment output. LCD segment output. LCD segment output. LCD segment output. LCD segment output. LCD segment output. GND. Connected to 6MHZ Ceramic Filter. Description CD read/write control output and TU CE. Data output to M62495FP. Output CLK to tuner PLL.(Not connected) Not Connected. Clock shift output of the microcomputer. Hold status detection. Microcomputer reset. Connected to 32.768KHZ crystal oscillator. Pin No. 51-54 55 56 57 58 59 60 61 62 63 64-66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 Pin Name S20- S23 O-CD LED O-TU LED O-TA LED O-ROCK LED O-POP LED O-JAZZ LED -- I-CD TEST I-TU TEST COM0-COM2 -- VSS2 VDD2 O-CD ON O-TU ON O-P.CONT
___________________
I/O -- O O O O O O -- -- -- O -- -- -- O O O O O O O O O I O Not connected.
Description
LED ON/OFF control output for CD functions. LED ON/OFF control output for TU functions. LED ON/OFF control output for TAPE functions. (Not Connected) LED ON/OFF control output for ROCK. LED ON/OFF control output for POP. LED ON/OFF control output for JAZZ. Not connected. Not connected. Not connected. LCD common output. Not connected. GND. Power supply for microcomputer (+5V). CD PWR control output. TU PWR control output. Power supply control output. Dubbing speed control output. Main mute output. FM mono/stereo output. BEAT switch over output. Q-Sound ON/OFF output. CD command output. CD sub-code Q input. CLK for CD commands/sub-codes.
O-H.DUBB O-MUTE O-MO/ST O-BEAT CONT O-QSOUND O-COIN I-SQOUT O-CQCK
33
34
MECHANICAL EXPLODED VIEW 1/1
32 34 35 36 18 31 B LCD 17 30 29 28 H e 19 P.C.B 20 F D D a GRILLE, SPKR L D 16 8 6 12 D e 7 9 A 10 10 11 b WIRE, FASTON ASSY ANT c 8 d 4 15 2 GRILLE, SPKR R CABI, FR U 9 B 49 D B 45 D A B P.C.B K BAR, ANT 40 B P.C.B D TN-21ZVC-2000 P.C.B CUSHION, CD A 22 H E 25 c d 21 SHIELD PLATE P.C.B 14 24 43 G 43 F B 46 P.C.B CHAS,TU A D P.C.B D RUBBER FOOT CHAS,TU B F CUSHION, CD A 27 H E 23 26 b 11 38 37 J 5 39 41 42 44 A P.C.B D I B C A 33 13 47 48
HT-SINK
a 3
1
35
36
MECHANICAL PARTS LIST 1/1
REF. NO
KANRI DESCRIPTION NO. 1 8Z-CL7-107-010 BADGE,AIWA SILVER 2 8A-CD8-007-010 WINDOW,CASS,52 U> 2 8A-CH8-040-010 WINDOW,CASS (L)<53 U> 2 8A-CH8-021-010 WINDOW,CASS (W)<52 U> 3 8A-CD8-006-010 BOX,CASS,52 U> 3 3 4 5 6 6 6 7 7 8A-CH8-039-010 8A-CH8-020-010 8A-CD8-207-010 8A-CD8-209-010 8A-CD8-018-010 8A-CH8-048-010 8A-CH8-029-010 8A-CH8-014-010 8A-CH8-003-010 BOX,CASS (L)<53 U> BOX,CASS (W)<52 U> SPR-T,CASS HLDR,TRANS PANEL,FR L,52 U> PANEL,FR L PANEL,FR L WINDOW,LCD WINDOW,LCD (L)<53 U> (W)<52 U> EX<51 K,51 EZ> U<51 U,53 U,52 U> SPKR,F 77 7OHM 3W HLDR,SPKR A HLDR,SPKR B GEAR CHAS,CASS,52 U> CHAS,CASS (L)<53 U> CHAS,CASS (W)<52 U> CONN ASSY,4P SP CONN ASSY,2P DOOR PANEL,FR R,52 U> PANEL,FR R (L)<53 U> PANEL,FR R (W)<52 U> KEY,CONTROL CD,52 U> KEY,CONTROL CD (L)<53 U> KEY,CONTROL CD (W)<52 U> KEY,VOL,52 U> KEY,VOL (L)<53 U> KEY,VOL (W)<52 U> KEY,QSOUND HLDR,LCD KEY,FUNC,52 U> KEY,FUNC KEY,FUNC KEY,CASS KEY,CASS KEY,CASS (L)<53 U> (W)<52 U> (L)<53 U> (W)<52 U> SET,52 U>
PART NO.
REF. NO 32 32 32 33 33
KANRI NO. 8A-CH8-037-010 8A-CH8-018-010 8A-CD8-027-010 8A-CH8-038-010 8A-CH8-019-010
PART NO.
DESCRIPTION BOX,CD (L)<53 U> BOX,CD (W)<52 U> BOX,CD EX,52 U> CHAS,CD (L)<53 U> CHAS,CD (W)<52 U> CHAS,CD EX,52 U> HANDL,FR,52 U> HANDL,FR (L)<53 U> HANDL,FR (W)<52 U> SW,PUSH LOCK HANDL,REAR,52 U> HANDL,REAR (W)<52 U> SPR-T,CD BRACKET PT,E 2.5W<51 K,51 EZ> PT,U 2.5W<51 U,53 U,52 U> CONN ASSY,4P RPH JACK,AC E W/SW<51 K,51 EZ> JACK,AC U W/SW<51 U,53 U,52 U> COVER,AC-SOCKET SPR-C,BATT HLDR,ANT FF-CABLE, 16P FR-MAIN LID,BATT,52 U> LID,BATT (L)<53 U> LID,BATT (W)<52 U> CABI,REAR,52 U> CABI,REAR (L)<53 U> CABI,REAR U (W)<52 U> ANT,ROD CONN ASSY,4P TP-ME UT2+3-30 W/O CR UT1+3-10 GLD U+3-12 CR UT2+3-8 GLD UT2+2.6-8 VT2+2.6-12 VIT+2-3 W,3.3-10-0.8 VT2+3-6 W10SL0T TAPPING SCREW, VFT1+3-12 TAPPING SCREW, VFTT+3-6
33 8A-CD8-028-010 34 34 34 35 8A-CD8-008-010 8A-CH8-041-010 8A-CH8-022-010 87-036-389-010
36 8A-CD8-009-010 36 37 38 39 8A-CH8-023-010 8A-CD8-208-010 84-CD5-216-010 8A-CD8-603-010
! !
8 88-CD8-622-010 9 10 11 12 12 12 13 14 15 8A-CD8-210-010 8A-CD8-211-010 84-CD5-215-010 8A-CD8-021-010 8A-CH8-047-010 8A-CH8-031-010 8A-CD9-633-010 8A-CD9-626-010 8A-CD8-022-010
39 8A-CD8-602-010 40 8A-CD9-630-010 41 87-A60-178-010 41 87-A60-177-010 42 87-A90-086-010 43 44 45 46 46 46 47 47 47 48 49 A B C D E F G H I 88-CD8-209-010 8A-CD8-212-010 8A-CD9-620-010 8A-CD8-003-010 8A-CH8-036-010 8A-CH8-017-010 8A-CH8-002-010 8A-CH8-035-010 8A-CH8-016-010 8Z-CH4-640-010 8A-CD9-631-010 87-B10-242-010 87-641-096-410 87-254-097-410 87-741-095-410 87-342-074-010 87-353-076-210 87-571-032-410 87-WA5-253-010 87-751-094-410
15 8A-CH8-049-010 15 8A-CH8-030-010 16 8A-CH8-005-010 16 8A-CH8-046-010 16 8A-CH8-027-010 17 8A-CD8-014-010 17 17 18 19 20 20 20 21 21 21 22 23 24 25 26 27 28 29 30 31 8A-CH8-044-010 8A-CH8-025-010 8A-CD8-017-010 8A-CH8-201-010 8A-CH8-004-010 8A-CH8-045-010 8A-CH8-026-010 8A-CH8-043-010 8A-CH8-024-010 8A-CD8-011-010 8A-CD8-213-010 M8-ZZK-E90-070 8A-CD9-622-010 8A-CD9-621-010 8Z-CDB-169-010 88-CD9-211-210 8Z-CDB-170-010 87-036-368-010 84-CT5-209-010 8Z-CH4-225-110
J 87-661-097-410 k 87-067-566-010
SPR-P,REC DA11T3C FF-CABLE, 8P CD-FR FF-CABLE, 16P CD-RF PANEL,CD SANYO RING,CHUCK BASE,CHUCK MAGNET PLATE,MAGNET HLDR,CHUCK A(S)
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange
37
TAPE MECHANISM EXPLODED VIEW 1/1
F G 52 46 1 E 2 3 47 4 5 LUG PLATE
25
8 a 9 10 J L 12 11
21 20 22 18 23 24 36 c 51 26 27 28 A 6 29 7 C 48 37 38 39 D D K 42 41 I 50 43 H B B 40 C a 34 35 c b 33 A 19 b 14 15 16 17 49 30 13 31 32
44
45
38
TAPE MECHANISM PARTS LIST 1/1
REF. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
KANRI DESCRIPTION NO. S1-921-030-4A0 HEAD BASE S1-821-030-070 AZIMUTH SPRING S1-921-030-090 PANEL P SPRING S1-921-260-050 GEAR PLATE SPRING S1-921-265-020 GEAR PLATE ASSY S1-510-020-020 S1-921-015-010 S1-921-030-110 S1-921-143-160 S1-921-141-8A0 S1-921-260-4A0 S1-921-043-100 S1-921-130-010 S1-921-141-3A0 S1-921-140-550 S1-921-140-120 S1-921-140-110 S1-921-140-150 S1-821-011-590 S1-921-141-070 S6-401-011-490 S1-921-140-090 S1-921-140-080 S1-921-140-190 S1-921-030-100 S1-921-140-040 S1-921-140-050 S1-921-140-060 S1-921-140-600 S1-821-100-700 S1-921-050-060 S1-921-053-100 S1-829-100-010 S1-921-050-150 S1-921-050-220 REC SPRING PLATE CHASSIS ASSY HEAD PANEL BASE ASSY M CONTROL SPRING SENSING LEVER PINCH ROLLER ARM ASSY EJECT SLIDE LEVER P CONTROL SPRING PAUSE LEVER(E) PAUSE LEVER SPRING PAUSE STOPPER BUTTON LEVER SPRING(B) E KICK LEVER BUTTON LEVER SPRING(A) LEAF SW MSW-1541T SWITCH ACTUATOR PUSH BUTTON ACTUATOR PLAY BUTTON LEVER MG ARM SPRING REW BUTTON LEVER FF,BUTTON REVER STOP BUTTON LEVER PAUSE BUTTON LEVER FF GEAR SENSER TAKE UP REEL ASSY PACK SPRING S REEL HUB BACK TENSION SPRING
PART NO.
36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 A B C D E F G H I J K L
S1-921-140-030 S1-921-140-170 S1-921-073-040 S1-921-070-030 S1-921-260-020 S1-921-140-160 S1-921-093-210 S1-921-090-380 S1-921-120-590 S6-002-030-220 S6-209-100-100 S1-921-030-050 S1-921-140-210 S1-821-100-690 S1-821-128-9A0 S1-821-010-500 S6-201-011-110 S9-P04-200-310 S1-921-120-020 S9-B10-200-510 S9-C07-204-510 S9-P01-200-610 S9-B01-200-310 S9-F08-200-710 S1-921-120-030 S9-W02-300-100 S9-W02-500-100 S9-W01-400-100 S9-W01-130-200
REC BUTTON LEVER P.S.LEVER SPRING RF CLUTCH ASSY RF BELT CAM GEAR E ACTUATOR SPRING FLYWHEEL ASSY MAIN BELT MOTOR PULLEY MOTOR EG530AD-2B E HEAD PH-K380-MS1 MG ARM REC BUTTON LEVER SPRING RECORD SAFETY LEVER MOTOR BRACKET PLAY BUTTON LEVER SPRING HEAD,RP7442ES-0951 C TAPPING SCREW 2-3 MOTOR COLLER SCREW P TAPPING BIND SCREW M2-5 SCREW,TAPPING(CAMERA)M2-4.5 SCREW,M2-6 (+)BIND SCREW M2-3 AZIMUTH SCREW M2-7 MB SCREW P P P P WASHER WASHER WASHER WASHER CUT 1.2-3.8-0.3 CUT 1.45-3.8-0.5 2-3.5-0.4 2.1-4-0.13
39
CD MECHANISM EXPLODED VIEW 1/1
B SHAFT,SLIDE
SF-P101NR
B 1
2 A
A CHASSIS 3
SPINDLE MOTOR(M3)
MOTOR C,B
40
CD MECHANISM PARTS LIST 1/1
REF. NO 1 2 3 A B
KANRI DESCRIPTION NO. S2-121-A28-400 COVER GEAR S2-511-A21-000 GEAR MIDDLE S2-511-A21-100 GEAR,DRIVE S1-PN2-03R-OSE SCR PAN PCS 2-3 87-261-073-410 SCR S-TPG FLT 2.6-6 DA11T3C
PART NO.
ALL M8-ZZK-E90-070
ACCESSORIES/PACKAGE LIST
REF. NO
! ! !
KANRI DESCRIPTION NO. 1 8A-CH8-906-010 IB,EZ(9L)B<51 EZ> 1 8A-CH8-905-010 IB,K(E)B<51 K> 1 8A-CH8-903-010 IB,U(ESF)B<51 U,53 U,52 U > 2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL<51 EZ> 2 87-A80-034-010 AC CORD SET ASSY,K W/F MAY-BG<51 K> 2 87-A80-109-010 AC CORD,HK7281 BLK U<51 U,53 U,52 U>
PART NO.
41
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
931196 Printed in Singapore