Text preview for : CSDTD 24 Rev.pdf part of Aiwa CSD-TD24, CSD-TD26, CSD-TD27, CSD-TD28 Service Manual Cd Fm Tape Recorder (Revision) - Tape mech. ZZM-1 AR5NC, Cd mech. DA11T3C - pag. 39
Back to : cd_radio_tape_rec_.part1. | Home
CSD-TD24 CSD-TD26 CSD-TD27 CSD-TD28
EZ,K U U U
SERVICE MANUAL
COMPACT DISC STEREO RADIO CASSETTE RECORDER BASIC TAPE MECHANISM: ZZM-1 AR5NC BASIC CD MECHANISM: DA11T3C
· This Service Manual is the "Revision Publishing" and replaces "Simple Manual" CSD-TD26/TD27/TD28 , (S/M Code No. 09-011-443-0T1) and CSD-TD24 , (S/M Code No. 09-012-443-0T2).
S/M Code No. 09-013-443-0R1
RE VI SIO DA N TA
SPECIFICATIONS
Frequency range FM AM 87.5 - 108.0 MHz Antenna: Rod antenna 530/531 - 1,710/1,602 kHz, (10/9 kHz step) Antenna: Ferrite bar antenna 531/530 - 1,602/1710 kHz, (9/10 kHz step) Antenna: Ferrite bar antenna 153 - 288 kHz Antenna: Ferrite bar antenna
Speaker Output Power output 100 mm cone type (2) Headphones jack(stereo mini-jack) U: 2.5 W + 2.5 W (EIAJ 7 ohms, T.H.D. 10 % DC) EZ: 2.9 W + 2.9 W (DIN MUSIC POWER) 2.5 W + 2.5 W (EIAJ 7 ohms, T.H.D. 10 % DC) 1.9 W + 1.9 W (DIN 1 %, Rated Power) K: 2.5 W + 2.5 W (EIAJ 7 ohms, T.H.D. 10 % DC) 1.9 W + 1.9 W (DIN 1 %, Rated Power) DC 12 V using eight size C (R14) batteries U: AC 120 V, 60 Hz EZ,K: AC 230 V, 50 Hz 15 W 414 x 183 x 235 mm (163/8 x 71/4 x 93/8 in.) 3.2 kg (7 lbs.1 oz.) (excluding batteries)
MW
LW
Track format Frequency range Recording system Erasing system Heads 4 tracks, 2 channels Normal tape: 50 - 12,500 Hz (EIAJ) AC bias Magnet erase Recording/playback head (1) Erasure head (1) Power requirements
Disc Scanning method Compact disc Non-contact optical scanner (semiconductor laser)
Power consumption Dimensions (W x H x D) Weight
· Design and specifications are subject to change without notice.
ACCESSORIES / PACKAGE LIST
REF. NO. PART NO. 1 1 1 2 2 8B-CHA-903-010 8B-CHA-906-010 8B-CHA-905-010 87-A80-109-010 87-A80-081-010
! !
KANRI DESCRIPTION NO. IB,U(ESF)FM IB,EZ(9L)FM IB,K(E)FM AC CORD,HK7281 BLK U AC CORD SET ASSY,EZ BLK
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in hazardous radiation exposure.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
s Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel: Usynlig laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
ATTENTION
L'utillisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
s
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saataa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. VARNING! Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
Precaution to replace Optical block (SF-P101NR)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
PICK-UP Assy PWB
Solder
3
ELETRICAL MAIN PARTS LIST
REF. NO. IC
PART NO.
KANRI NO.
DESCRIPTION
REF. NO. C805 C806 C807 C808 C809 C810 C811 C812 C816 C817 C821 C822 C823 C824 C829 C830 C834 C843 C844 C845 C846 C851 C852 C853 CN201 CN801 CNA302 CNA801 L108 L801 SW801 CD C.B
PART NO.
87-A21-928-010 87-A21-193-010 87-A21-520-040 87-A21-443-040 87-A20-446-010 87-A21-319-010 87-A21-891-010 8B-CHA-600-010 87-A21-550-010 87-A21-607-010 TRANSISTOR 87-026-447-080 87-026-463-080 89-318-154-080 89-112-965-080 87-026-291-080 87-026-464-080 87-A30-476-010 87-026-462-080 89-109-332-380 87-A30-515-080 89-320-011-080 87-A30-288-040 87-A30-287-040 87-A30-455-040 87-026-239-080 87-026-237-080 87-A30-283-040 89-111-624-080 89-503-025-010 DIODE 87-A40-650-080 87-A40-509-080 87-070-345-080 87-A40-648-080 87-A40-234-080 87-017-978-080 87-017-932-080 87-020-465-080 87-A40-465-010 87-017-090-080 MAIN C.B C211 C212 C215 C216 C231 C232 C233 C234 C235 C236 C237 C239 C239 C240 C240 C247 C248 C310 C316 C317 C801 87-A11-603-080 87-A11-603-080 87-016-460-080 87-016-460-080 87-010-213-080 87-010-213-080 87-A10-201-080 87-A10-201-080 87-016-669-080 87-016-669-080 87-010-371-080 87-010-197-080 87-010-805-080 87-010-197-080 87-010-805-080 87-010-401-080 87-010-401-080 87-010-248-080 87-010-263-080 87-010-197-080 87-010-248-080
IC,LC72131D-N IC,TA8227P C-IC,M61509FP C-IC,M62495AFP C-IC,LA9241ML C-IC,LC78622NE C-IC,MM1469XH C-IC,LC867132V-5T67 IC,TA2149N IC,NJM14558LD
KANRI NO. 87-012-365-080 87-012-365-080 87-010-406-080 87-010-405-080 87-010-401-080 87-010-401-080 87-010-178-080 87-010-178-080 87-010-180-080 87-010-180-080 87-010-401-080 87-010-401-080 87-010-178-080 87-010-178-080 87-010-178-080 87-010-178-080 87-010-248-080 87-A11-132-080 87-018-124-080 87-010-178-080 87-010-263-080 87-010-186-080 87-018-131-080 87-A11-132-080 87-099-018-010 87-A60-110-010 8B-CDA-629-010 8B-CDA-630-010 87-003-097-080 87-007-342-010 8Z-CD9-609-010
DESCRIPTION C-CAP,S 0.027-25VBK C-CAP,S 0.027-25VBK CAP, ELECT 22-50V CAP, ELECT 22-50V CAP, ELECT 1-50V CAP, ELECT 1-50V CHIP CAP 1000P CHIP CAP 1000P C-CER 1500P C-CER 1500P CAP, CAP, CHIP CHIP CHIP CHIP CAP, CAP, CAP, CHIP ELECT 1-50V ELECT 1-50V CAP 1000P CAP 1000P CAP 1000P CAP 1000P ELECT 220-10V TC U 0.01-50 KB CER 270P-50V CAP 1000P
TR,2SC1740SR TR,2SA933SRS TR,2SC1815Y TR,2SA1296GR TR,DTC124XS TR,DTC114TS TR,KTA1046Y TR,2SC1740SRS TR,2SA933RS TR,2SA1979O/Y TR,2SC2001K C-TR,DTC114YKA C-TR,DTC114TKA C-TR,DTA144EKA C-TR,DTC114TK C-TR,DTC124XK C-TR,DTA114YKA C-TR,2SA1162Y C-FET,2SK302GR
CAP, ELECT 100-10V CAP,CHIP 4700P CAP, TC U 1000P CAP,TC U 0.01-50 K B CONN,16P CONN,4P V S2M-4W CONN ASSY,6P MA-TU CONN ASSY,4P RPH COIL,1.0UH K LAL02 COIL,OSC 85K BIAS SW,SL 1-6-2 PS62D01
ZENER,MTZJ6.8A ZENER,MTZJ6.8C DIODE,IN4148 ZENER,MTZJ8.2A ZENER,MTZJ5.6A DIODE,1N4003 ZENER,MTZJ6.2B DIODE,1SS133 DIODE,FR202 ZENER,HZS5B3
C30 C251 C263 C264 C265 C266 C267 C268 C271 C272 C278 C279 C301 C306 C307 C308 C311 C312 C321 C322 C324 C325 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413
87-010-260-080 87-010-405-080 87-010-178-080 87-010-178-080 87-010-263-080 87-010-263-080 87-010-385-080 87-010-385-080 87-010-221-080 87-010-221-080 87-010-385-080 87-010-235-080 87-016-495-000 87-010-404-080 87-010-401-080 87-010-221-080 87-010-265-080 87-010-385-080 87-010-197-080 87-010-263-080 87-010-260-080 87-010-405-080 87-010-403-080 87-010-197-080 87-010-263-080 87-010-248-080 87-010-197-080 87-010-374-080 87-010-178-080 87-010-198-080 87-010-248-080 87-010-263-080 87-A11-177-080 87-010-401-080 87-016-369-080
CAP, CAP, CHIP CHIP CAP, CAP, CAP, CAP, CAP, CAP,
ELECT 47-25V ELECT 10-50V CAP 1000P CAP 1000P ELECT 100-10V ELECT ELECT ELECT ELECT ELECT 100-10V 220-25V 220-25V 470-10V 470-10V
CAP, ELECT 220-25V CAP, ELECT 470-16V CAP,E 3300-25 M SMG CAP, ELECT 4.7-50V CAP, ELECT 1-50V CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CAP, CHIP CAP, ELECT 470-10V ELECT 33-16V ELECT 220-25V CHIP 0.01 DM ELECT 100-10V ELECT 47-25V ELECT 10-50V ELECT 3.3-50V CHIP 0.01 DM ELECT 100-10V ELECT 220-10V CHIP 0.01 DM ELECT 47-10V CAP 1000P CHIP 0.022
C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S
0.15-16 K B 0.15-16 K B 0.22-16 B 0.22-16 B 0.015-50 B
C-CAP,S 0.015-50 B C-CAP,S0.33-16 KB C-CAP,S0.33-16 KB C-CAP,S 0.1-25 K B C-CAP,S 0.1-25 K B CAP, ELECT 470-6.3V CAP, CHIP 0.01 DM C-CAP,S 1-16 Z F CAP, CHIP 0.01 DM C-CAP,S 1-16 Z F CAP, ELECT 1-50V CAP, ELECT 1-50V CAP, ELECT 220-10V CAP, ELECT 100-10V CAP,CHIP 0.01 DM CAP, ELECT 220-10V
CAP, ELECT 220-10V CAP, ELECT 100-10V C-CAP,S 0.15-16 K B CAP, ELECT 1-50V C-CAP,S 0.033-25 B K
4
REF. NO. C414 C416 C417 C418 C419 C420 C421 C422 C423 C424 C425 C426 C428 C429 C430 C431 C432 C433 C434 C435 C436 C437 C438 C439 C440 C441 C442 C445 C446 C447 C448 C451 C455 C457 C458 C459 C460 C461 C462 C463 C465 C466 C467 C469 C470 C471 C472 C473 C474 C475 C476 C477 C478 C479 C480 C481 C482 C489 C490 C491 C492 C493 C501 C502 C503 C504 C505 C506 C510 C831
PART NO.
KANRI NO. 87-010-405-080 87-010-545-080 87-012-157-080 87-010-213-080 87-A11-608-080 87-016-369-080 87-A11-177-080 87-010-184-080 87-010-992-080 87-A11-606-080 87-018-129-080 87-A11-608-080 87-010-197-080 87-010-186-080 87-012-156-080 87-010-545-080 87-010-374-080 87-010-401-080 87-010-184-080 87-010-197-080 87-010-374-080 87-010-404-080 87-016-669-080 87-010-178-080 87-018-139-080 87-010-197-080 87-018-109-080 87-012-368-080 87-012-368-080 87-012-368-080 87-010-315-080 87-012-156-080 87-010-247-080 87-010-312-080 87-010-312-080 87-010-263-080 87-015-819-080 87-010-197-080 87-010-248-080 87-A11-132-080 87-010-404-080 87-012-368-080 87-010-263-080 87-012-154-080 87-018-131-080 87-018-209-080 87-015-785-080 87-015-785-080 87-015-785-080 87-A11-132-080 87-010-236-080 87-010-197-080 87-010-263-080 87-010-197-080 87-010-221-080 87-010-405-080 87-010-405-080 87-012-368-080 87-012-368-080 87-A11-132-080 87-010-221-080 87-010-180-080 87-012-368-080 87-010-322-080 87-018-119-080 87-010-322-080 87-010-322-080 87-010-322-080 87-016-669-080 87-010-198-080
DESCRIPTION CAP, ELECT 10-50V CAP, ELECT 0.22-50V C-CAP,S 330P-50 CH C-CAP,S 0.015-50 B C-CAP,S 0.33-25 K B C-CAP,S 0.033-25 B K C-CAP,S 0.15-16 K B CHIP CAPACITOR 3300P(K) C-CAP,S 0.047-25 B C-CAP,S 0.22-25 K B CAP,TC U 680P-50 K B C-CAP,S 0.33-25 K B CAP, CHIP 0.01 DM CAP,CHIP 4700P C-CAP,S 220P-50 CH CAP, CAP, CAP, CHIP CAP, ELECT 0.22-50V ELECT 47-10V ELECT 1-50V CAPACITOR 3300P(K) CHIP 0.01 DM
REF. NO. CN202 CN205 CN301 CN401 CN403 CN802 CNA202 CNA205 CNA402 CNA802 FFC401 FFC403 J201 JW429 JW442 L401 L402 L404 R840 SFR430 X401 FRONT C.B C601 C602 C603 C604 C605 C606 C607 C608 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C625 C626 C627 CN601 CN602 CNA603 FFC601 L601 L602 LCD601 LED601 LED602 LED603 S601 S602 S603 S604 S605 S606 S607 S608 S609 S611 S612 S613 S614
PART NO.
KANRI NO. 8A-CH4-687-010 87-A60-109-010 8A-CH4-689-010 87-A60-424-010 87-099-201-010 8A-CH4-687-010 8B-CDA-633-010 8B-CDA-626-010 8B-CDA-625-010 8B-CDA-631-010 8B-CDA-621-010 8B-CDA-622-010 87-A60-420-010 87-003-283-080 87-003-098-080 87-003-102-080 87-003-098-080 87-003-152-080 87-029-124-010 87-024-437-080 8Z-CD5-633-010
DESCRIPTION CONN,4P V 2.5 CONN,2P V S2M-2W CONN,3P V 2.5 CONN,16P V TOC-B CONN,8P 6216 H CONN,4P V 2.5 CONN ASSY,4P SP CONN ASSY,2P DOOR CONN ASSY,6P CD-ME CONN ASSY,4P TA-ME FF-CABLE,16P CD-RF FF-CABLE,8P CD-FR JACK,3.5 ST (MSC) COIL,18UH J LAL02 COIL,2.2UH K LAL02 COIL, 10UH COIL,2.2UH K LAL02 COIL, 100UH RES,FUSE 2.2-1/4 SFR,100K RH063MC VIB, CER16.93MHZ FCR16.93M2
CAP, ELECT 47-10V CAP, ELECT 4.7-50V C-CAP,S 0.1-25 K B CHIP CAP 1000P CAP,TC U 1P-50 CH CAP, CHIP 0.01 DM CAP, TC U 22P-50 SL C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F C-CAP,S 27P-50 CH C-CAP,S 220P-50 CH CAP, ELECT 100-50V C-CAP,S 15P-50 CH C-CAP,S 15P-50 CH CAP, ELECT 100-10V CAPACITOR,0.01 CAP, CHIP 0.01 DM CAP, ELECT 220-10V CAP, TC U 0.01-50 KB CAP, ELECT 4.7-50V C-CAP,S 0.1-50 F CAP, ELECT 100-10V C-CAP,S 150P-50 CH CAP,TC U 1000P-50 KB UP050 CAP, CHIP CHIP CHIP CAP, TC U 0.1-50 ZF CAPACITOR, 0.1FZ-25Z CAPACITOR, 0.1FZ-25Z CAPACITOR, 0.1FZ-25Z TC U 0.01-50 K B
87-010-196-080 87-010-555-040 87-A10-189-040 87-010-196-080 87-018-150-080 87-018-111-080 87-018-116-080 87-018-114-080 87-018-149-080 87-015-785-080 87-010-197-010 87-018-131-080 87-A10-826-080 87-010-494-040 87-010-493-040 87-010-196-080 87-010-495-040 87-010-197-010 87-010-197-010 87-010-197-010 87-010-197-010 87-010-197-010 87-099-757-010 87-A60-079-010 8B-CHA-610-010 8B-CDA-620-010 87-003-102-080 87-003-102-080 8B-CHA-620-010 8A-CDA-646-010 8A-CDA-645-010 8A-CDA-645-010 87-A92-170-080 87-A92-170-080 87-A92-170-080 87-A92-170-080 87-A92-170-080 87-A92-170-080 87-A92-170-080 87-A92-170-080 87-A91-704-080 87-A92-170-080 87-A92-170-080 87-A92-170-080 87-A92-170-080
C-CAP,S 0.1-25 Z F C2012 CAP,E 100-10 M 5L SRE CAP,E 220-10 M 5L C-CAP,S 0.1-25 Z F C2012 CAP,TC U 18P-50 J CH UP050 CAP,TC U 27P-50 J SL UP050 CAP,TC U 56P-50 J SL UP050 CAP,TC U 39P-50 J SL UP050 CAP,TC U 15P-50 J CH UP050 C-CAP,0.1-25 Z F C3216 CAP,CHIP 0.01 DM CAP,TC U 1000P-50 K B UP050 C-CAP,S 1-10 K B CAP,E 1-50 M 5L SRE CAP,E 0.47-50 M 5L SRE C-CAP,S 0.1-25 Z F C2012 CAP E 2.2-50 M 5L SRE CAP, S 0.01-25 CAP, S 0.01-25 CAP,CHIP 0.01 DM CAP,CHIP 0.01 DM CAP,CHIP 0.01 DM CONN,16P H 9604 CONN,08P H 9604S-08F CONN ASSY,4P TU-FR FF-CABLE,16P FR-MAIN COIL,10UH J LAL02 COIL,10UH J LAL02 LCD,AIW4239-32PIN LED,6224-10GD GRN LED,6224-10ID RED LED,6224-10ID RED SW,TACT EVQPAD05R SW,TACT EVQPAD05R SW,TACT EVQPAD05R SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT SW,TACT EVQPAD05R EVQPAD05R EVQPAD05R EVQPAD05R EVQPAD05R EVQ 214 05R EVQPAD05R EVQPAD05R EVQPAD05R EVQPAD05R
CAP,E 1000-10 SME CAP, CHIP 0.01 DM CAP, ELECT 100-10V CAP, CHIP 0.01 DM CAP, ELECT 470-10V CAP, ELECT 10-50V CAP, ELECT 10-50V C-CAP,S 0.1-50 F C-CAP,S 0.1-50 F CAP, TC U 0.01-50KB CAP, ELECT 470-10V C-CER 1500P C-CAP,S 0.1-50 F C-CAP,S 100P-50 CH CAP,TC U 100P-50 KB C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 100P-50 CH C-CAP,S 0.1-25 K B CAP, CHIP 0.022
5
REF. NO. S615 X601 X602 TUNER C.B C1 C2 C3 C5 C6 C7 C7 C8 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C23 C24 C25 C27 C28 C29 C30 C30 C31 C31 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C56 C71 C72 C73 C75 C80 C92 C93 CF1 CF2 CN2 CN3
PART NO.
KANRI DESCRIPTION NO. 87-A92-170-080 SW,TACT EVQPAD05R 87-030-273-010 VIB,XTAL 32.768KHZ DT-38 5P 87-030-376-080 VIB,CER 5.760MHZ CSA MG200
REF. NO. D3 D4 D5 L2 L3 L3 L4 L5 L6 L7 L8 L51 TC1 TC51 X1 BATT C.B C901 C902 C903 C904 CNA901
! ! ! ! !
PART NO.
KANRI NO. 87-A40-616-070 87-A40-916-040 87-A40-916-040 87-A50-560-010 8A-CH4-670-010 8A-CH4-671-010 87-A50-420-010 87-A50-566-010 87-A50-567-010 87-A91-308-010 87-005-849-080 87-A50-421-010 87-011-254-080 87-A91-659-010 87-A70-061-010
DESCRIPTION VARI-CAP,SVC384(S/T) C-VARI-CAP,HVC202A C-VARI-CAP,HVC202A COIL,FM BPF(ACD) BAR-ANT,MW 2B-ACH(COI) BAR-ANT,MW/LW 3B-ACH(COI) COIL,MW OSC(SYN) COIL,FM RF EX(ACH) COIL,FM OSC(ACH) FLTR,PCFAZH- 450T (TOK) COIL,10UH K CECS COIL,LW OSC(SYN) TRIMMER,CER 20P 4.0X4.5 ECR TRIMMER,50P 4.0X4.5 ECRL VIB,XTAL 4.500MHZ CSA-309
87-010-312-080 87-010-316-080 87-010-312-080 87-012-360-080 87-010-313-080 87-012-140-080 87-014-049-080 87-012-349-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-150-080 87-010-303-080 87-010-178-080 87-010-374-080 87-010-198-080 87-015-835-080 87-010-263-080 87-010-404-080 87-010-197-080 87-010-303-080 87-016-460-080 87-A11-067-080 87-016-669-080 87-016-669-080 87-012-365-080 87-010-220-080 87-012-365-080 87-010-220-080 87-012-358-080 87-012-358-080 87-010-197-080 87-010-263-080 87-010-197-080 87-010-263-080 87-010-404-080 87-010-197-080 87-010-178-080 87-010-178-080 87-010-178-080 87-010-311-080 87-010-312-080 87-010-197-080 87-010-197-080 87-010-197-080 87-012-140-080 87-010-197-080 87-010-316-080 87-010-197-080 87-010-197-080 87-010-177-080 87-010-197-080 87-010-312-080 87-010-197-080 87-010-263-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-197-080 87-010-197-080 87-A91-094-010 87-008-261-010 87-099-854-010 87-A60-110-010
C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S
15P-50 33P-50 15P-50 1-10 Z 18P-50
J CH GRM CH J CH GRM F CM/CB J CH GRM
C-CAP,S 470P-50 J CH CAP,PP 470P-100 J PL C-CAP,S 1000P-50 J CH GRM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CAP,S 6P-50 D CH C-CAP,330P-50 J CH C-CAP,S 1000P-50 K B C2012 CAP,E 47-10 M 11L SME C-CAP,S 0.022-25 K B C2012 C-CAP,0.047-50 K B CAP,E 100-10 M 11L SME CAP,E 4.7-50V CAP, CHIP 0.01 DM C-CAP,330P-50 J CH C-CAP,S 0.22-16 K B C-CAP,S 1-10 K B C-CAP,S 0.1-25 K B C-CAP,S 0.1-25 K B C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 0.027-25 K B 0.018-25 K B 0.027-25 K B 0.018-25 K B 0.47-10 Z F CM/CB
87-010-192-080 87-010-192-080 87-010-192-080 87-010-192-080 8B-CDA-627-010 87-A60-178-010 87-A60-177-010 87-A91-940-080 8A-CDA-612-010 8A-CDA-611-010 8A-CDA-214-010 8A-CDA-214-010
C-CAP,S 0.022-50 C-CAP,S 0.022-50 C-CAP,S 0.022-50 C-CAP,S 0.022-50 CONN ASSY,3P PWR
F F F F
J901 J901 PR901 PT901 PT901 SP901 SP902
JACK,AC E W/SW JACK,AC U W/SW PROTECTOR,2.5A 20P 60V PT,E 2.5W PT,U 2.5W SPR-C,BATT SPR-C,BATT
BATT INF C.B SP903 SP904 8A-CDA-214-010 8A-CDA-214-010 SPR-C,BATT SPR-C,BATT
C-CAP,S 0.47-10 Z F CM/CB CAP, CHIP 0.01 DM CAP, ELECT 100-10V CAP, CHIP 0.01 DM CAP,E 100-10 M 11L SME CAP,E 4.7-50 M 11L CAP, CHIP 0.01 DM C-CAP,S 1000P-50 K C-CAP,S 1000P-50 K C-CAP,S 1000P-50 K C-CAP,S 12P-50 C-CAP,S 15P-50 CAP, CHIP 0.01 CAP, CHIP 0.01 CAP, CHIP 0.01 SME B C2012 B C2012 B C2012
CD MOTOR C.B M2 PIN3 SW1 S0-M10-A09-700 S2-369-750-000 S4-S13-A01-600 MOTOR SLED ASSY PLUG,6P SW,LEAF
J CH GRM J CH GRM DM DM DM
C-CAP,S 470P-50 J CH CAP, CHIP 0.01 DM C-CAP,S 33P-50 J CH GRM CAP, CHIP 0.01 DM CAP, CHIP 0.01 DM C-CAP,S 820P-50 J SL CAP, CHIP 0.01 DM C-CAP,S 15P-50 J CH GRM CAP, CHIP 0.01 DM CAP, ELECT 100-10V CAP, CAP, CAP, CAP, CAP, CHIP CHIP CHIP CHIP CHIP 0.01 0.01 0.01 0.01 0.01 DM DM DM DM DM
FLTR,CDA10.7 MG80A FILTER, SFE10.7MA5-A CONN,6P V S2M-6W CONN,4P V S2M-4W
6
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Resistor Code Value of resistor Chip resistor
Dimensions (mm)
Figure
Wattage 1/16W 1/16W 1/10W 1/8W
Type 1005 1608 2125 3216
Tolerance 5% 5% 5% 5%
Symbol CJ CJ CJ CJ
Form
L W
L 1.0
t
W 0.5 0.8 1.25 1.6
t 0.35 0.45 0.45 0.55
:A Resistor Code : A
104 108 118 128
1.6 2 3.2
TRANSISTOR ILLUSTRATION
C
B E C B E C B E C B E
2SA1979O/Y 2SC2001K
2SA1296GR 2SC1815Y
2SA933RS 2SA933SRS 2SC1740SR 2SC1740SRS DTC114TS DTC124XS
S
2SA1162Y DTA114EKA DTA114YKA DTC114TK DTC114TKA DTC114YKA DTC124XK
D G B C E
2SK302GR
KTA1046Y
7
LCD DISPLAY (AIW4239-32PIN)
8
WIRING 1 (MAIN / CD)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U
9
SCHEMATIC DIAGRAM 1 (MAIN / CD : 1 / 2)
10
SCHEMATIC DIAGRAM 2 (CD : 2 / 2 / CD MOTOR)
11
WIRING 2 (FRONT / BATT / BATT INF)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H I J K L M N O P Q R S T U
12
SCHEMATIC DIAGRAM 3 (FRONT)
13
SCHEMATIC DIAGRAM 4 (BATT / BATT INF)
14
WIRING 3 (TUNER)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A B C D
,
E F
,
G H I J K L M N O P Q R S T U
TP (VT)
15
SCHEMATIC DIAGRAM 5 (TUNER)
16
SCHEMATIC DIAGRAM 6 (TUNER)
17
WIRING 4 (CD MOTOR)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A
G CD MOTOR C.B
M2 _ M2 (SLED MOTOR) SW1 (INSIDE LIMIT SW) M1
B C D E F
TO MAIN C.B CNA402
+
PIN3
6 5 3 1
SW1 _ +
G H I J
M1 (SPINDLE MOTOR) PICK UP ASSY SF-P101NR
K L M N O P Q
CN1
1 16
R S
FFC401
T U
TO MAIN C.B CN401
18
IC BLOCK DIAGRAM
19
20
IC DESCRIPTION
IC, LC78622NE Pin No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
Pin Name
DEFI TAI PDO VVSS ISET VVDD FR VSS EFMO EFMIN T2 CLV+
I/O
I I O I I O I I O Defect detection signal (DEF) input.
Description
Test input. A pull-down resistor is incorporated. (For PLL) (Connected to 0V) Phase comparison output to control the external VCO. (For PLL) Ground of the built-in VCO. Normally, 0V. (For PLL) For the connection of a resistor which adjusts the PDO output current. (For PLL) Power supply of the built-in VCO. (For PLL) Adjusts the VCO frequency range. (For PLL) Ground of digital circuits. Normally, 0V. Slice level control EFM signal output. Slice level control EFM signal input. Test input. A pull-down resistor is incorporated. (Connected to 0V) Disc motor control tri-state output. Output to monitor the automatic switching between the rough servo control and phase servo
CLVV/P HFL TES TOFF TGL JP+ O JPPCK FSEQ VDD SL+ O SL NC PU IN RW EMPH C2F DOUT T3 I T4 NC MUTEL O Not connected. Left channel 1-bit D/A converter muting output. (Not used) Test input. (Connected to 0V). I O O O O Not connected. CD pickup inside limit switch. Read / Write signal. De-emphasis monitor. "H": when playing a de-emphasis disc. (Not used) C2 flag output. (Not used) Output a digital OUT signal. (EIAJ format) (Not used) Serial data command sled signal output terminal from microprocessor. O O signal matches the sync signal generated internally. (Not used) Power supply of digital circuits. Monitors clock signal for EFM data playback. 4.3218MHz when the phase is locked. (Not used) Sync signal detection output. Goes "H" when the sync signal detected from the EFM Track jump control tri-state output. O control. "H": Rough servo, "L": Phase servo. I I O O Track detection signal input. Schmitt trigger input. Track error signal input. Schmitt trigger input. Tracking OFF output. Tracking gain switching output. "L" raises the gain.
21
Pin No.
36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Pin Name
LVDD LCHO LVSS RVSS RCHO RVDD MUTER XVDD XOUT XIN XVSS SBSY EFLG PW SFSY SBCK FSX WRQ RWC SQOUT COIN CQCK RES T11 16M 4.2M T5 CS T1
I/O
O O O O
Description
Left channel 1-bit D/A converter power supply. Left channel 1-bit D/A converter output. Left channel 1-bit D/A converter ground. Normally, 0V. Right channel 1-bit D/A converter ground. Normally, 0V. Right channel 1-bit D/A converter output. Right channel 1-bit D/A converter power supply. Right channel 1-bit D/A converter muting output. (Not used) Power supply of crystal oscillator. For the connection of a 16.93MHz crystal oscillator.
I O O O O I O O I O I I input. I O O O I I I LC78622NE reset input. Test output. Set to open (normally, "L" output.) (Not used) 16.9344MHz output. (Not used) 4.2336MHz output. Test input. A pull-down resistor is incorporated. (Connected to 0V) Chip select input. (Connected to 0V) Test input with no pull-down resistor. (Connected to 0V) Ground of crystal oscillator. Normally, 0V. Subcode block sync signal output. (Not used) C1, C2, single, duplex correction monitor. (Not used) Output of subcodes P, Q, R, S, T, U and W. (Not used) Subcode frame sync signal output. Falls when the subcode is set to the standby state. (Not used) Subcode read-out clock input. Schmitt trigger input. ("L" is applied when not used.) (Connected to 0V) 7.35kHz sync signal output obtained by dividing the oscillator frequency. (Not used) Subcode Q standby output. Read/write control input. Schmitt trigger input. Subcode Q output. Command input from the microprocessor. Command input retrieval clock or subcode retrieval clock input from SQOUT. Schmitt trigger
22
IC, LA9241ML Pin No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Pin Name
FIN2 FIN1 E F TB TETE TESI SCI TH TA TDTD JP TO FD FDFA FAFE FEA-GND SP SPI SPG 26 27
I/O
O
Description
For the connection of the pickup photodiode. Addition to the FIN1 pin creates an RF signal and subtraction from it create an EF signal.
O O
For the connection of the pickup photodiode. For the connection of the pickup photodiode. Subtraction from the F pin creates a TE signal.
O I O
For the connection of the pickup photodiode. Inputs the DC components in the TE signal. For the connection of a resistor which sets the gain of the TE signal between this pin and the TE pin.
O I I I O I O I O O I O I O I
TE signal output. TES (track error sense) comparator input. The TE signal is passed through a BPF. Shock detection input. Sets the time constant for the tracking gain. TA amp output. Composes the tracking phase compensation constant between the TD and VR pins. Sets the tracking phase compensation. Sets the amplitude of the tracking jump signal (kick pulses). Tracking control signal output. Focusing control signal output. Composes the focusing phase compensation constant between the FD and FA pins. Composes the focusing phase compensation constant between the FD- and FA- pins. Composes the focusing phase compensation constant between the FA and FE pins. FE signal output. For the connection of a resistor whichs sets the gain of the FE signal between this pin and the TE pin.
O O I I SPSPD I O I
Ground of analog signals. Single-ended output of the signals input to the CV+ and CV- pins. Spindle amp input. For the connection of a resistor which sets the gain in the spindle 12cm mode. (Not used) I For the connection of the spindle phase compensation constant with the SPD pin.
O Spindle control signal output. For the connection of sled phase compensation constant. Sled control signal output. Sled feed signal input from the microprocessor.
28 29 30 31 32 33 34 35 36
SLEQ SLD SLSL+ JP-
I JP+ TGL TOFF TES I I O
Tracking signal input from the DSP. Tracking gain control signal input from the DSP. Low gain when TGL is "H". Tracking off control signal input from the DSP. Off when TOFF is "H". Outputs the TES signal to the DSP.
23
Pin No.
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Pin Name
HFL SLOF CV-
I/O
O the pit or on the mirror. I I Sled servo off control input. CLV error signal input from the DSP. RF output.
Description
The HFL (high frequency level) signal is used to judge whether the main beam is positioned on
CV+ RFSM RFSSLC SLI DGND FSC TBC NC DEF CLK CL DAT CE DRF FSS VCC2 REFI VR LF2 PHI BHI LDD LDS VCC1 O O O waveform. I O I O I I I I O I respect to the reference voltage). (Not used) O I I I O I VCC of servo and digital circuits. For the connection of bypass capacitor for the reference voltage. Reference voltage output. Sets the time constant for disc defect detection. For the connection of a capacitor to hold the RF signal peak. For the connection of a capacitor to hold the RF signal bottom. APC circuit output. APC circuit input. VCC of RF signal circuits. Input to control the DSP's data slice level. Ground of digital signals. Output for the focus search smoothing capacitor. The TBC (tracking balance control) signal sets the EF balance variation range. Not connected. Disc defect detection output. Reference clock input. 4.23MHz is input from the DSP. Microprocessor command clock input. Microprocessor command data input. Microprocessor chip enable input. DRF (detect RF) is an output to detect the RF level. The FSS (focus search select) signal switches the focus search modes (+/-search / +search with
Sets the RF gain and the EFM signal's 3T compensation constant together with the RFSM pin. The SLC (slice level control) signal is output to control the DSP's data slice level of the RF
24
IC, LC867132V-5T67
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 ~ 40 41 42 43 ~ 51 52 ~ 63 64 ~ 66 67 68 69 70 Pin Name O-RWC/CE O-DATA O-CLK O-DI O-CLK.SFT I-HOLD I-RST XT1 (IN) XT2 (OUT) VSS1 CF1 (IN) CF2 (OUT) VDD1 I-FM.ST I-KEY0 I-CD SW I-KEY1 I-MOTOR I-REC NC I-DO O-BASS.LED O-QS.LED NC O-INT I-DRF I-WRSQ I-RMC SEG1 SEG2/LW SEG3/AM 10K SEG4 ~ SEG12 VDD3 VSS3 SEG13 ~ SEG21 NC COM1 ~ COM3 NC VSS2 VDD2 O-CD I/O O O O O O I I I O I O I I I I I I I O O O I I I O O O O O O O Description CD read/write control output and TU CE. Data output to sound processor IC M62495AFP, IC M61509FP. Clock output to sound processor IC M62495AFP, IC M61509FP. Data input to tuner PLL. Clock shift output for microprocessor. Hold status detection. Microcomputer reset. Connected to an external 32.768kHz crystal oscillator. Connected to an external 32.768kHz crystal oscillator. GND. Connected to an external 5.76MHz ceramic filter. Connected to an external 5.76MHz ceramic filter. Microprocessor power supply (+5V). FM STEREO status input. KEY AD input. CD door switch status detection input. KEY AD input. DECK MECHA MOTOR status input. REC status input. (Connected to GND through a resistor). Not connected. Data input from tuner PLL. BASS LED ON/OFF control output. (Not used) Q-Sound LED ON/OFF control output. Not connected. INT DIODE MATRIX detection output. CD RF level detection input. CD sub-code Q standby input. Remote control input. LCD segment output. LCD segment output / Intial settings output (LW) . LCD segment output / Intial settings output (AM 10K) . LCD segment output. Power supply for microcomputer (+5V). GND. LCD segment output. Not connected. LCD common output. Not connected. GND. Power supply for microcomputer (+5V). CD power control output.
25
Pin No. 71 72 73 74 75, 76 77 78 79 80
Pin Name O-TU O-P.CONT NC O-MUTE NC O-BEAT CONT O-COIN I-SQOUT O-SQCK
I/O O O O O O I O TUNER power control output. Power supply control output. Not connected. Main mute output. Not connected. BEAT switch over output. CD command output. CD sub-code Q input. CLK for CD commands/sub-codes.
Description
26
VOLTAGE CHART
IC001, TA2149N
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 FM 0 0.79 0 4.65 4.84 4.3 4.84 0 0.21 4.06 1.19 1.21 3.93 4.16 0.7 0.94 0.9 4.79 3.1 4.84 4.64 4.84 4.64 4.83 AM 0 0 1.01 4.79 4.83 4.16 4.83 0 0.18 4.34 1.19 1.22 0 0.02 0.7 1.09 1.3 4.74 3.22 4.83 4.76 4.83 4.76 4.83 PIN NO. 15 16 17 18 19 20 21 22 FM 0 2.4 4.8 0.8 0.8 5 0 2.4 AM 0 2.4 4.8 0.8 0.8 5 0 2.4
IC203, M61509FP / M62495AFP
PIN NO. 1 2,3 4 5 6 7 8 9 10 CD 2.54 2.55 0.7 2.54 2.56 2.55 2.55 2.55 2.55 2.56 5.08 2.82 0 2.55 2.55 2.55 2.57 2.54 0.7 2.54 2.55 2.54 TAPE 2.55 2.55 0.8 2.55 2.56 2.55 2.56 2.55 2.55 2.56 5.09 2.83 0 2.55 2.56 2.55 2.57 2.55 0.58 2.06 2.56 2.55 TUNER 2.56 2.56 2.56 2.57 2.57 2.57 2.57 2.56 2.57 2.57 5.11 2.83 0 2.56 2.57 2.56 2.58 2.57 0.69 2.56 2.56 2.56
IC202, TA8227P
PIN NO. 1 2 3 4 5 6,7 8 9 10 11 12 ACTIVE 12.31 6.57 12 0 0.56 0 0.56 6.65 12 6.46 13.1 STATIC 11.5 6.1 1.5 0 0.56 0 0.56 6.41 1.42 6.2 12.5
11 12 13 14 15,16 17 18 19 20 21 22 23 24
IC002, LC72131D-N
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 FM 2.4 0 0 0 0 4.8 0 1.3 4.7 4.0 4.8 0 0.9 0 AM 2.4 0 0 0 0 4.8 0 1.3 0 0 0 0 0.9 0
27
IC401, LA9241ML
PIN NO. 1 2 3 4 5 6 7,8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32,33 34 35 36 37 38 39 40 41 42 43 44 ACTIVE 2.67 2.65 2.67 2.67 2.67 2.66 2.67 2.65 2.66 2.67 2.7 2.67 2.7 2.72 2.69 2.67 2.69 2.73 2.69 0 2.67 2.67 2.65 2.69 2.75 2.75 2.68 2.75 2.45 2.45 0 5.22 0 1.4 0 0 0 0.25 2.45 2.54 2.54 2.63 STATIC 2.53 2.53 2.53 2.56 2.53 2.55 2.55 2.54 2.52 2.55 2.54 2.55 2.54 2.54 2.54 2.55 2.55 2.54 2.54 2.54 0 2.53 2.54 2.56 2.56 2.5 2.55 2.55 2.33 2.34 0 5.01 5.01 0.04 0.01 5 0 0 1.61 2.45 2.41 2.53 PIN NO. 45 46 47 48,49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 ACTIVE 0 2.64 2.65 0 2.54 4.77 4.86 0 5.11 0.16 5.2 2.64 2.64 2.59 2.57 2.3 3.86 0.19 5.18 STATIC 0 2.54 2.55 0 2.44 4.71 4.71 0.07 0.03 0.14 5.01 2.54 2.56 0.98 0.99 2.24 4.35 0 5.02 PIN NO. 21 22 23 24,25 26 27 28,29 30 31 32~34 35 36 37 38,39 40 41 42 43 44 45 ACTIVE 2.7 5.6 5.6 0 0 5.6 0 0 2.8 0 0 5.3 2.15 0 2.15 5.3 0 5.5 2.3 2.3 2.3 0.1 0 0.1 2.77 0 2.77 0.9 0 0 5.16 5 5.5 0 2.25 2.66 0 STATIC 2.48 0 5.02 0 5 5 0 4.95 2.48 0 5.02 4.77 1.94 0 1.95 4.77 5 5.02 2.08 2.06 0 0.08 2.27 0 2.5 0 2.5 0 0.07 0 4.71 4.71 5 0 2.02 2.41 0
IC402, LC78622NE
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19,20 ACTIVE 0 0 1.8 0 2.1 5.6 0.4 0 2.8 2.7 0 0.3 0 0 0 1.5 0 5.6 0 STATIC 0 0 0.01 0 1.85 4.98 0.07 0 2.52 2.41 0 0 0 5 0.01 0.04 5.01 5.01 0
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62~64
28
IC404, MM1469XH
PIN NO. 1 2 3,4 5 6,7 8 9 10 11 12 13 14 15 16 17 18 19 20 21,22 23,24 25 26 27 28 ACTIVE 4.2 4.2 2.95 8.2 5.8 0 2.95 3 4.27 4.01 0 8.4 1.45 1.45 4.1 4.1 2.9 2.9 8.9 2.9 2.9 4.5 3.71 0 STATIC 3.61 3.62 2.54 7.24 5.02 0 2.55 2.55 3.61 3.63 0 7.39 0.78 0.8 3.63 3.62 2.54 2.55 7.96 2.55 2.54 3.61 3.62 0
IC601, LC867132V-5T67
PIN NO. 1 2 3,4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19,20 21 22~24 25 26,27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 TAPE 0.01 0.02 0.01 0.01 0.03 4.01 1.7 2.47 0.01 2.08 2.19 4.74 0 4.93 4.6 4.93 0.73 0.61 0 0.01 4.74 0.02 5.17 0 0.38 2.43 2.43 2.40 0.6 2.40 2.43 0.6 2.43 2.43 2.43 4.75 0.01 2.43 2.43 2.43 2.43 2.43 TUNER 0.01 0.01 0.01 0.01 0.03 4.70 1.74 2.52 0.01 4.41 4.84 4.85 4.79 4.95 4.73 4.95 0.73 0.01 4.82 0.01 4.85 0.03 5.27 2.45 2.45 2.41 0.85 2047 2.47 2.46 2.48 2.48 2.48 2.48 2.41 4.85 0.01 2.46 2.48 2.47 2.45 2.42 CD 0.01 0.02 0.01 0.03 0.03 4.61 1.69 2.46 0.01 2.08 2.19 4.74 0.02 4.93 4.71 4.93 0.73 0.04 0.01 0.01 4.74 0.37 5.17 2.37 2.37 2.37 2.43 2041 2.41 2.41 2.41 2.43 2.43 2.39 2.38 4.75 0.01 2.43 2.43 2.41 2.43 2.44 PIN NO. 48 49 50 51 52 53,54 55 56 57 58~60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75~77 78 79 80 TAPE 2.43 2.43 2.43 2.41 2.43 0.01 0.01 0.01 4.75 0.01 0.05 0.04 0.03 2.41 2.42 2.41 0.01 0.01 4.74 0.01 0.01 4.73 4.75 0.01 0.01 0.01 1.15 0.01 TUNER 2.45 2.42 2.47 2.47 2.47 0 0 0 4.78 0 0.15 0.1 0.61 2.47 2.44 2.48 1.25 0 4.84 0 4.85 4.83 0.15 0.01 0.01 0.01 0.01 0.45 CD 2.43 2.43 2.43 2.42 2.43 0.01 4.68 0.01 0.01 0.01 0.42 0.45 0.34 2.41 2.41 2.41 0.04 0.01 4.74 4.74 0.01 4.74 4.74 4.67 0.01 4.74 0 4.74
IC801, NJM14558LD
PIN NO. 1 2 3 4 5 6 7 8 TAPE 3.37 3.37 3.34 0 3.34 3.37 3.37 6.83 REC 3.38 3.39 3.35 0 3.35 3.39 3.38 6.82
29
Q002
PIN E C B FM 4.82 8 5.52 AM 4.9 8 5.58
Q244
PIN E C B ACTIVE 0 0 0.12 STATIC 0 0 0.64
Q310
PIN E C B ACTIVE 5.55 10.45 6.25 STATIC 5.56 10.83 6.26
Q003
PIN E C B FM 5.53 5.52 4.85 AM 5.59 5.59 4.9
Q301
PIN E C B ACTIVE 12.2 11.4 11.5 STATIC 12.66 12 11.99
Q321
PIN E C B ACTIVE 0 0.01 0.6 STATIC 0 0.02 0.7
Q004
PIN E C B FM 0 4.06 2.98 AM 0 4.12 3.03
Q302
PIN E C B ACTIVE 11.5 11.4 10.9 STATIC 11.99 12 11.32
Q401
PIN E C B ACTIVE 4.46 2.11 3.76 STATIC 4.99 1.56 4.35
Q052
PIN E C B FM 0.01 0.61 4.82 AM 0.01 0.62 0
Q303
PIN E C B ACTIVE 0 0 4.57 STATIC 0 0 4.57
Q402
PIN E C B ACTIVE 7.87 5.3 7.17 STATIC 7.97 5.15 7.28
Q054
PIN E C B FM 4.82 0 4.79 AM 4.81 4.75 0.03
Q304
PIN E C B ACTIVE 11.38 7.94 10.75 STATIC 11.97 7.98 11.34
Q403
PIN E C B ACTIVE 2.56 2.56 0 STATIC 2.56 2.56 0
Q071
PIN E C B FM 0 0.02 4.42 AM 0 0.01 4.42
Q305
PIN E C B ACTIVE 7.23 10.56 7.85 STATIC 7.26 11.23 7.87
Q406
PIN E C B ACTIVE 0 4.6 0 STATIC 0 4.6 0
Q243
PIN E C B ACTIVE 0 0 0.12 STATIC 0 0 0.64
Q306
PIN E C B ACTIVE 5.08 7.94 10.75 STATIC 5.09 7.98 5.81
Q407
PIN E C B ACTIVE 4.6 2.57 2.56 STATIC 4.58 2.55 2.55
30
Q408
PIN E C B ACTIVE 4.6 2.57 2.56 STATIC 4.58 0.55 2.55
Q492
PIN E C B ACTIVE 0 0.14 4.41 STATIC 0 0.14 4.41
Q810
PIN E C B TAPE 3.36 0.05 0.13 REC 3.38 13.85 0.13
Q491
PIN E C B ACTIVE 7.91 7.88 7.15 STATIC 7.98 7.97 7.23
Q801
PIN E C B TAPE 0 0 0 REC 1.64 5.9 2.31
Q841
PIN E C B TAPE 0 0.72 0 REC 0 0.01 5.73
31
ADJUSTMENT
< TUNER SECTION > 1. AM IF Adjustment
L007 ................................................ 450kHz 2. AM(MW) VT Adjustment Settings : · Test Point : C39 ) (VT) · Adjustment location : L004 Method : Set to AM 1000kHz(U), MW 999kHz(EZ, K) and adjust L004 so that the test point becomes 3.75V±0.1V(U), 3.8V±0.1V(EZ, K). 3. AM(MW) Tracking Adjustment L003 (1/2) ................................. 600kHz(U) L003 (1/2) .......................... 603kHz(EZ, K) TC001 ..................................... 1400kHz(U) TC001 .............................. 1404kHz(EZ, K) 4. FM VT Adjustment Settings : · Test point : C39 ) (VT) · Adjustment location : L006 Method : Set to FM 108.0MHz and adjust L006 so that the test point becomes 6.0V± 0.1V. 5. FM Tracking Adjustment L005 ................................................ 98MHz 6. LW VT Adjustment Settings : · Test point : C39 ) (VT) · Adjustment location : L051 Method : Set to LW 288kHz and adjust L051 so that the test point becomes 4.5V± 0.1V. 7. LW Tracking Adjustment L003 (2/2) ....................................... 153kHz TC051 ............................................. 288kHz
< DECK SECTION >
8. Bias Frequency Adjustment Settings : · Test tape : TTA-602 · Test point : L801 pin 1 · Adjustment location : L801 Method : L801 ..................................... 85kHz ± 2kHz 9. Tape Speed Adjustment Settings : · Test tape : TTA-100 · Test point : PHONES JACK (J201) · Adjustment location : SFR of deck motor Method : Play back the test tape and adjust SFR so that the output frequency is 3000Hz + 90Hz/-60Hz. 10. Azimuth Adjustment Settings : · Test tape : TTA-320 · Test point : PHONES JACK (J201) · Adjustment location : Azimuth adjustment screw Method : Play back the test tape and adjust the screw so that the output is maximum.
< CD SECTION >
11. Focus Bias Adjustment Settings : · Test point : IC401 PIN58 (VREF), IC401 PIN20 (FE) · Adjustment location : SFR430 · Test disc : TCD-782 (YEDS-18) second track Method : Play back the disc and adjust SFR430 so that the voltage between the test point becomes 0~-10mV.
32
MECHANICAL EXPLODED VIEW 1 / 1
22 20 23 33 34
21 B 19 H 35 37 38 PWB 31 C 30 E PWB 39 I 36 B
32 18 47 25
11
J
D
17 16 DA11T3C G 6 A A 15 A 14 C A PWB 8 12 LCD601 9 48 4 A 2 A A 3 6 A ZZM-1 AR5NC K 46 40 A PWB 13 10 7 27 C 28 24 A A 29 A PLATE,ANT PLATE,PT A 26
45 44
42 41
PWB PWB
5
11
43
F PWB
PWB
1
33
MECHANICAL PARTS LIST 1 / 1
REF. NO. 1 1 1 1 2 2 3 4 4 4 4 4 5 5 5 5 5 5 6 7 7 7 7 8 8 8 9 10 10 10 10 11 12 13 14 15 15 15 15 16 17 18 19 20 20 20 20 21 21 22 23 24 24 24 24 25 26 27 28 29 30 31 32 32 33 33 34 34 35 36
PART NO.
KANRI NO. 8B-CDA-113-010 8B-CDA-009-010 8B-CDA-093-010 8B-CDA-073-010 8B-CDA-003-010 8B-CDA-132-010 8A-CDA-212-010 8B-CHA-025-010 8B-CHA-012-010 8B-CHA-026-010 8B-CHA-015-010 8B-CDA-138-010 8B-CHA-023-010 8B-CHA-005-010 8B-CHA-024-010 8B-CHA-014-010 8B-CHA-019-010 8B-CHA-016-010 8B-CDA-615-010 8B-CDA-020-010
DESCRIPTION WINDOW,CASS (R)<[R]24EZ> WINDOW,CASS<[S]24EZ,[S]24K,[S]26U,[W]27U> WINDOW,CASS (G)<[G]24EZ> WINDOW,CASS (L)<[L]28U> LID,CASS LID,CASS U (W)<[W]27U> SPR-T,CASS WINDOW,DISP EZ G<[G]24EZ> WINDOW,DISP EZ K<[S]24EZ,[S]24K> WINDOW,DISP EZ R<[R]24EZ> WINDOW,DISP U<[S]26U,[W]27U> WINDOW,DISP U (L)<[L]28U> CABI ASSY,FRONT EZ G<[G]24EZ> CABI ASSY,FRONT EZ K<[S]24EZ,[S]24K> CABI ASSY,FRONT EZ R<[R]24EZ> CABI ASSY,FRONT U<[S]26U> CABI ASSY,FRONT U L<[L]28U> CABI ASSY,FRONT U W<[W]27U> SPKR,10 7OHM KEY,STOP<[S]24EZ,[S]24K,[S]26U,[W]27U> KEY,STOP KEY,STOP KEY,STOP KEY,FUNC KEY,FUNC (G)<[G]24EZ> (L)<[L]28U> (R)<[R]24EZ> A<[S]26U,[W]27U,[L]28U> C<[S]24EZ,[S]24K>
8B-CDA-096-010 8B-CDA-077-010 8B-CDA-116-010 8B-CDA-015-010 8B-CDA-017-010 8B-CHA-030-010 8B-CDA-014-010 8B-CDA-019-010 8B-CDA-095-010 8B-CDA-076-010 8B-CDA-115-010 87-063-165-010 8B-CHA-201-010 8B-CDA-622-010 8B-CDA-620-010 8B-CDL-008-010 8B-CDA-106-010 8B-CDA-107-010 8B-CDA-136-010 8Z-CT6-213-110 8Z-CT6-214-110 87-036-368-010 86-CT9-217-110 8B-CDA-006-010 8B-CDA-104-010 8B-CDA-105-010 8B-CDA-135-010 8B-CDA-005-010 8B-CDA-063-010 87-036-389-010 8A-CDA-211-010 8B-CDA-021-010 8B-CDA-097-010 8B-CDA-078-010 8B-CDA-117-010 8Z-CDB-169-010 8B-CDA-621-010 88-CH6-220-010 8B-CDA-630-010 8B-CDA-631-010 8B-CDA-633-010 8B-CDA-626-010 8B-CDA-010-010 8B-CHA-022-010 8B-CDA-007-010 8B-CHA-021-010 8B-CDA-004-010 8B-CHA-020-010 87-A91-857-010 8B-CHA-003-010
KEY,FUNC F<[G]24EZ,[R]24EZ> KEY,CD KEY,PAUSE<[S]24EZ,[S]24K,[S]26U,[W]27U> KEY,PAUSE (G)<[G]24EZ> KEY,PAUSE (L)<[L]28U> KEY,PAUSE (R)<[R]24EZ> OIL-DMPR 150 HLDR,LCD FF-CABLE,8P CD-FR FF-CABLE,16P FR-MAIN PANEL,TOP<[S]24EZ,[S]24K,[S]26U,[W]27U> PANEL,TOP G<[G]24EZ> PANEL,TOP R<[R]24EZ> PANEL,TOP U (L)<[L]28U> BASE,CHUCK RING,CHUCK MAGNET HLDR,CHUCK A(S) LID,CD<[S]24EZ,[S]24K,[S]26U,[W]27U> LID,CD G<[G]24EZ> LID,CD R<[R]24EZ> LID,CD U (L)<[L]28U> CHAS,CD CHAS,CD (W)<[W]27U> SW,PUSH LOCK SPR-T,CD KEY,FF<[S]24EZ,[S]24K,[S]26U,[W]27U> KEY,FF (G)<[G]24EZ> KEY,FF (L)<[L]28U> KEY,FF (R)<[R]24EZ> PANEL,CD SANYO FF-CABLE,16P CD-RF CUSHION,CD A CONN ASSY,4P RPH CONN ASSY,4P TA-ME CONN ASSY,4P SP CONN ASSY,2P DOOR LID,HANDL LID,HANDL W<[W]27U> HANDL,ARM HANDL,ARM W<[W]27U> LID,BATT LID,BATT W<[W]27U> ANT,ROD 5SEC709 CABI,REAR
34
REF. NO. 36 37 37 38 39 39 40 41 42 43 43 43 43 44 44 44 44 45 45 45 45 46 47 48 A B C D E F G H I J K
PART NO.
! !
! !
KANRI NO. 8B-CHA-018-010 87-A60-178-010 87-A60-177-010 8Z-CD5-634-010 8A-CDA-612-010
DESCRIPTION CABI,REAR U W<[W]27U> JACK,AC E W/SW JACK,AC U W/SW COVER,AC SOCKET PT,E 2.5W PT,U 2.5W HLDR,TU PLATE,REC SPR-P,REC KEY,REC<[S]24EZ,[S]24K,[S]26U,[W]27U> KEY,REC (G)<[G]24EZ> KEY,REC (L)<[L]28U> KEY,REC (R)<[R]24EZ> KEY,PLAY<[S]24EZ,[S]24K,[S]26U,[W]27U> KEY,PLAY (G)<[G]24EZ> KEY,PLAY (L)<[L]28U> KEY,PLAY (R)<[R]24EZ> KEY,REW<[S]24EZ,[S]24K,[S]26U,[W]27U> KEY,REW (G)<[G]24EZ> KEY,REW (L)<[L]28U> KEY,REW (R)<[R]24EZ> HLDR,WIRE PLATE,MAGNET KEY,FUNC B QT2+3-10 GLD VT2+3-30 SCREW 2.6-12 U+3-12 CR S-SCREW,CD S-SCREW,CASS+2.6-4 VT2+3-10 GLD VT2+3-12 W/O SLOT VF+3-4 QT2+2.6-8 W/O SLOT VT2+3-10 W/O SLOT
8A-CDA-611-010 8B-CDA-202-010 8A-CDA-220-010 8A-CDA-221-010 8B-CDA-024-010 8B-CDA-100-010 8B-CDA-081-010 8B-CDA-120-010 8B-CDA-023-010 8B-CDA-099-010 8B-CDA-080-010 8B-CDA-119-010 8B-CDA-022-010 8B-CDA-098-010 8B-CDA-079-010 8B-CDA-118-010 87-064-185-010 86-CT9-222-010 8B-CDA-016-010 87-721-096-410 87-751-104-410 87-751-076-410 87-254-097-410 8A-CK4-223-010 8A-CDA-222-010 87-751-096-410 87-751-097-410 87-501-092-410 87-721-074-410 87-751-096-410
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green YM Metallic Yellow DM Metallic Orange PT Transparent Pink LA Aqua Blue GL Light Green HT Transparent Gray
35
TAPE MECHANISM EXPLODED VIEW 1 / 1
12
11 A TERMINAL,LB1 10 9 21 4 8 14 7 55 3 42 6 2 1 5 13 17 27 28 30 18 54 19 15 31 20 23 22
26 16 24 53 C B 52 51 1 35 47 46 45 50 44 49 48 43 41 39 40 38 36 37 32 34 33 25 29
36
TAPE MECHANISM PARTS LIST 1 / 1
REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
PART NO.
KANRI NO. 8Z-ZM1-254-310 8Z-ZM1-225-110 8Z-ZM1-253-210 8Z-ZM1-217-110 8Z-ZM1-212-110
DESCRIPTION SPR-C,REEL R GEAR,REEL R SPR-C,AUTO SENSOR LEVER,AUTO SENSOR LEVER,T-UP SPR-T,AUTO CLR,SLIP FF/REW SPR-C,FF/REW GEAR,SLIP FF/REW A FELT,FF/REW 2 GEAR,SLIP FF/REW B 2 LEVER,FF/REW 2 LEVER,PAUSE 2 LEVER,E-LOCK M LEVER,E-OPEN SPR-T,T-UP SPR-T,PINCH ROLLER ASSY,PINCH LEVER,PINCH LEVER,PLAY SPR-T,BRG HEAD,AP-4211T4 SPR-C,AZIMUTH LEVER,AUTO SPR-T,AUTO 2 GEAR,IDL REW LEVER,STOP LEVER,FF LEVER,REW LEVER,REC 2
REF. NO. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 A B C
PART NO.
KANRI NO. 87-A91-819-010 8Z-ZM1-215-010 87-A91-492-010 8Z-ZM1-226-010 8Z-ZM1-241-210
DESCRIPTION HEAD,EH 2NSS-2200 LEVER,REC LOCK SW,LEAF MSW18560 GEAR,REEL L SPR-T,PLAY LEVER,REC SENSOR SPR-T,FR SPR-T,FF/REW GEAR,CAM TD20 GEAR,IDL FF/REW FLY-WHL ASSY,ZZM1 W-L,1.47-4-0.25 GEAR,SLIP T-UP B FELT,T-UP GEAR,SLIP T-UP A SPR-C,T-UP SLIP SPR-T,STOP/PAUSE MOT,M09Y/Z PULLEY,MOT ZZM-1 BELT,MAIN S SPR-P,CASETTE CHAS ASSY,ZZM-1 SPR-T,E-LOCK LEVER,LOCK SPR-C,F/R S-SCREW,AZ1-2-6.4 V+2.6 ZZM-1 W-L,1.63-3.2-0.5 SLIT
8Z-ZM1-245-310 8Z-ZM1-236-010 8Z-ZM1-252-110 8Z-ZM1-230-010 8Z-ZM1-269-010 8Z-ZM1-238-110 8Z-ZM1-237-110 8Z-ZM1-283-010 8Z-ZM1-222-010 8Z-ZM1-219-010 8Z-ZM1-244-110 8Z-ZM1-247-310 8Z-ZM1-261-110 8Z-ZM1-221-210 8Z-ZM1-205-310 8Z-ZM1-248-210 87-A92-207-010 84-ZM2-227-310 8Z-ZM1-216-110 8Z-ZM1-246-110 8Z-ZM1-233-110 8Z-ZM1-208-010 8Z-ZM1-207-010 8Z-ZM1-206-010 8Z-ZM1-211-210
8Z-ZM1-220-110 8Z-ZM1-249-210 8Z-ZM1-242-310 8Z-ZM3-244-010 8Z-ZM1-232-010 82-ZM1-290-010 8Z-ZM1-275-010 8Z-ZM1-228-010 8Z-ZM1-265-010 8Z-ZM1-227-010 8Z-ZM1-251-210 8Z-ZM1-243-310 87-A91-825-010 8Z-ZM1-271-010 8Z-ZM1-264-010 8Z-ZM1-260-010 8Z-ZM1-201-910 8Z-ZM1-255-310 8Z-ZM1-214-210 8Z-ZM1-257-110 84-ZM2-242-010 8Z-ZM1-270-110 87-B10-301-010
37
CD MECHANISM EXPLODED VIEW 1 / 1
1
A
2
3
4
SW1
CD MOTOR C.B
PIN 3
M2 (SLED MOTOR)
CD MECHANISM PARTS LIST 1 / 1
REF. NO. PART NO. 1 2 3 4 A M8-ZZK-E90-070 S2-121-A28-400 S2-511-A21-000 S2-511-A21-100 S1-PN2-03R-OSE
KANRI DESCRIPTION NO. DA11T3C COVER GEAR GEAR MIDDLE GEAR DRIVE SCR PAN PCS 2-3
38
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9820543 2000045 0251431 Printed in Singapore