Text preview for : AIWA 4ZG-1.pdf part of AIWA NSX-A222/AS222/S333223/ Service Manual, schematics and parts list for Aiwa compact disc/stereo cassette receiver.
Back to : AIWA CX-NA222.part1.rar | Home
4ZG-1
English
SERVICE MANUAL
CD MECHANISM KSM-2131FAM 3ZG-2 E1 BASIC CD MECHANISM : 3ZG-2 E3 3ZG-2 E4 TYPE Z3NDSH Z3RDLSHJ Z3RNDSHJ Z3RNDSH Z3RNSMDJ Z3RSHMDJ PZ3MD Z4RNDSH Z4RNSHMDJ BASIC CD MECHANISM 3ZG-2 E1 3ZG-2 E3 3ZG-2 E1 3ZG-2 E1 3ZG-2 E1 3ZG-2 E3 3ZG-2 E4 KSM-2131 FAM KSM-2131 FAM
S/M Code No. 09-992-325-4N2
A AT D
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserståling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for stråling.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que ceux spécifiés peut entraîner une dangereuse exposition aux radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude af funktion. Undgå udsættelse for stråling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i denna bruksanvising, kan användaren utsättas för osynling laserstrålning, som överskrider gränsen för laserklass 1.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1
LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT
2
Precaution to replace Optical block (KSS-213F)
Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure.
3
How to Adjust the Rotating Phase of the Gear, Main Cam
1) Push down the hooking catch of the CHAS. MECH, and remove the TRAY. 2) Align the arrow mark of the Gear, Main Cam with the black round mark of the CHAS, MECHA as shown below. 3) Confirm that the Slide, Mech Cam is located in the right position, then insert the TRAY gently. Caution: If the rotating phase of the Gear, Main Cam is incorrectly adjusted, the chucking operation and tray movement will have malfunction.
Align the arrow 2 mark with the black round · mark.
4
ELECTRICAL MAIN PARTS LIST
REF. NO IC
PART NO.
KANRI NO.
DESCRIPTION
REF. NO C102 C103 C104 C105 C109 C111 C112 C113 C115 C116 C117 C118 C119 C121 C122 C123 C124 C131 C191 C301 C302 C303 C501 C502 C504 C505 C506 C507 C509 C510 C603 C610 C611 C701 C705 C706 C707 C711 C712 C713 C901 C902 CON3 CON3 CON4 CON5 CON6 CON8 CON8 CON9 FC1 FC4 FC5 L11 L101 L102 L902 LED901 LED901 M601 R50 R51
87-A20-446-010 87-A20-459-010 87-A20-445-010 88-NF9-621-010
C-IC,LA9241ML C-IC,LC78622ED IC,BA5936 IC,BA5936S
KANRI NO. 87-016-081-080 C-CAP,S 87-010-321-020 C-CAP,S 87-012-154-020 C-CAP,S 87-010-196-020 C-CAP,S 87-010-197-020 C-CAP,S 87-010-312-020 87-010-154-020 87-010-322-020 87-010-404-080 87-010-196-020 87-010-263-040 87-010-178-020 87-010-154-020 87-010-403-080 87-010-403-080 87-012-157-020 87-012-157-020 87-010-382-080 87-010-263-040 87-010-196-020 87-010-382-080 87-010-260-040 87-A10-730-080 87-010-197-020 87-010-196-020 87-010-196-020 87-010-196-020 87-010-196-020 87-010-196-020 87-010-196-020 87-010-196-020 87-010-405-080 87-010-405-080 87-010-405-040 87-010-197-020 87-010-196-020 87-010-196-020 87-010-322-020 87-010-322-020 87-010-322-020 87-010-260-080 87-010-196-020 84-ZG1-648-010 87-099-199-010 87-099-212-010 87-099-199-010 87-099-030-010 87-A60-248-010 87-A60-429-010 87-009-345-010 85-NFT-611-110 84-ZG1-672-010 84-ZG1-630-010 87-005-602-080 87-005-614-080 87-005-602-080 87-A50-189-080 87-A40-558-010 87-A40-123-010 87-045-305-010 88-118-124-020 88-118-124-020
PART NO.
DESCRIPTION 0.1-16 RK 82P-50 CH 150P-50 J CH GRM 0.1-25 Z F GRM 0.01-25 B
TRANSISTOR 89-113-187-080 87-026-609-080 87-026-295-080 87-A30-076-080 89-406-554-580 87-A30-047-080 87-A30-073-080 87-A30-075-080 DIODE 87-A40-527-080 87-020-465-080 87-A40-470-080 3CD C.B C11 C12 C13 C14 C15 C16 C17 C18 C19 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C31 C32 C32 C33 C35 C37 C38 C39 C40 C41 C42 C43 C44 C46 C47 C48 C49 C50 C51 C52 C101 87-012-393-080 87-012-157-020 87-016-369-080 87-A10-201-080 87-010-213-020 87-016-083-080 87-010-184-020 87-016-083-080 87-010-198-020 87-016-369-080 87-010-178-020 87-012-393-080 87-016-083-080 87-010-197-020 87-010-186-020 87-010-400-040 87-010-322-020 87-010-382-040 87-010-545-040 87-010-184-020 87-010-186-020 87-010-315-020 87-010-312-080 87-016-081-080 87-010-196-020 87-010-405-080 87-010-263-080 87-010-596-020 87-010-401-080 87-010-805-080 87-010-263-080 87-010-197-020 87-010-263-080 87-010-196-020 87-010-260-080 87-010-196-020 87-010-404-080 87-010-197-020 87-010-263-040 87-012-156-080 87-016-369-020 C-CAP,S 0.22-16 R K C-CAP,S 330P-50 CH C-CAP,S 0.033-25 B K C-CAP,S0.33-16 KB C-CAP,S 0.015-25 B C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 0.15-16 RK 3300P-50 B 0.15-16 RK 0.022-25 B 0.033-25 B K 1000P-50 B 0.22-16 R K 0.15-16 RK 0.01-25 B 4700P-50 B DIODE,1SS133 T-91S DIODE,1SS133 (110MA) DIODE,1SS254 TR,2SA1318TU TR,KTA1266GR TR,DTC144TK C-TR,2SC3052F TR,2SD655DE TR,CSD655E C-TR,RT1N 141C C-TR,2SA1235F
C-CAP,S 15P-50 J CH C-CAP,S 10P-50 CH C-CAP,S 100P-50 CH CAP, ELECT 4.7-50V C-CAP,S 0.1-25 Z F GRM CAP,E 100-10 C-CAP,S 1000P-50 B C-CAP,S 10P-50 CH CAP, ELECT 3.3-50V CAP, ELECT 3.3-50V C-CAP,S 330P-50 CH C-CAP,S 330P-50 CH CAP, ELECT 22-25V CAP,E 100-10 C-CAP,S 0.1-25 Z F GRM CAP, ELECT 22-25V CAP,E 47-25 SME CAP,E 1000-16 SMG C-CAP,S 0.01-25 B C-CAP,S 0.1-25 Z F GRM C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 0.1-25 0.1-25 0.1-25 0.1-25 0.1-25 Z Z Z Z Z F F F F F GRM GRM GRM GRM GRM
C-CAP,S 0.1-25 Z F GRM CAP, ELECT 10-50V CAP, ELECT 10-50V CAP,E 10-50 C-CAP,S 0.01-25 B C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 0.1-25 Z F GRM 0.1-25 Z F GRM 100P-50 CH 100P-50 CH 100P-50 CH
CAP,E 0.47-50 C-CAP,S 100P-50 CH CAP,E 22-25 SME CAP,E 0.22-50 SME C-CAP,S 3300P-50 B C-CAP,S C-CAP,S C-CAP,S C-CAP,S C-CAP,S 4700P-50 B 27P-50 CH 15P-50 CH 0.1-16 RK 0.1-25 Z F GRM
CAP, ELECT 47-25V C-CAP,S 0.1-25 Z F GRM CONN ASSY,6P CONN,6P 6216 H CONN,5P 6216 V CONN,6P 6216 H CONN,13P 6216H CONN,16P H CFF1416 CONN,16P H TOC-A CONN,2P PH H FF-CABLE 16P-1.0 F-CABLE,5P 1.25 210MM WHITE N CABLE FFC 6P-1.25 COIL,10UH LAV35 J COIL 100UH LAV35 J COIL,10UH LAV35 J C-COIL,S BLM21B272S LED,SLZ-8128A-01-A LED,SLZ-8128A-01-B MOTOR, RF-500TB DC-5V (2MA) C-RES,S 120K-1/10W J C-RES,S 120K-1/10W J
CAP, ELECT 10-50V CAP, ELECT 100-10V C-CAP,S 0.047-16 RK CAP, ELECT 1-50V CAP, S 1-16 CAP, ELECT 100-10V C-CAP,S 0.01-25 B CAP, ELECT 100-10V C-CAP,S 0.1-25 Z F GRM CAP, ELECT 47-25V C-CAP,S 0.1-25 Z F GRM CAP, ELECT 4.7-50V C-CAP,S 0.01-25 B CAP,E 100-10 C-CAP,S 220P-50 CH C-CAP,S 0.033-25 B K
5
REF. NO R52 R53 SFR101 SW701 SW702 X101
KANRI DESCRIPTION NO. 88-118-124-020 C-RES,S 120K-1/10W J 88-118-124-020 C-RES,S 120K-1/10W J 87-A90-787-080 SFR,100K H HOKU 87-036-109-010 PUSH SWITCH 87-036-109-010 PUSH SWITCH 87-A70-046-010 VIB,XTAL 16.934MHZ
PART NO.
KANRI NO. DRIVE C.B M1 M2 SW1 87-045-358-010 87-045-356-010 87-A90-042-010
REF. NO
PART NO.
DESCRIPTION
MOT,RF-310TA 43 MOT,RF-310TA 30 SW,MSW-17310MVPO
MOTOR C.B LED C.B LED701 LED702 LED702 LED703 LED704 T-T C.B C401 CON401 M401 PS401 PS401 87-A11-148-080 86-NFZ-675-010 87-045-364-010 87-026-573-010 88-NF9-627-010 CAP,TC U 0.1-50 Z F CONN,5P H 6216-11H MOTOR(BCH3B14) IC,GP1S53V SNSR,SG-240 87-A40-316-080 87-A40-316-080 87-A40-268-080 87-A40-268-080 87-A40-316-080 LED,SLR-56PCT31 LED,SLR-56PCT31 LED,SLH-56DCT31 LED,SLH-56DCT31 GRN GRN ORN ORN LED,SLR-56PCT31 GRN M2 PIN3 SW1 9X-262-513-210 91-564-722-110 91-572-085-110 SLED MOTOR CONNECTOR 6P LEAF SW
· Regarding connectors, they are not stocked as they are not the initial order items. The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Resistor Code Value of resistor Chip resistor
Dimensions (mm)
Figure
Wattage 1/16W 1/16W 1/10W 1/8W
Type 1005 1608 2125 3216
Tolerance 5% 5% 5% 5%
Symbol CJ CJ CJ CJ
Form
L W
L 1.0
t
W 0.5 0.8 1.25 1.6
t 0.35 0.45 0.45 0.55
:A Resistor Code : A
104 108 118 128
1.6 2 3.2
TRANSISTOR ILLUSTRATION C
B
E
ECB 2SD655 KTA1266
2SA1235 2SC3052 DTC144TK
6
BLOCK DIAGRAM
7
8
WIRING
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
B
C
D
E
F
G
H
I
J
K 9 10
SCHEMATIC DIAGRAM
11
12
WAVE FORM
1
IC11 Pin = (RFSM)
VOLT/DIV: 0.5V TIME/DIV: 1µS
4
IC11 Pin (SPD)
VOLT/DIV: 100mV TIME/DIV: 1mS
IC BLOCK DIAGRAM IC, BA5936
MAX 2.0±0.1 Vp-p 0V EYE PATTERN must be CLEAR and MAX VREF
2
IC11 Pin ^ (FD)
VOLT/DIV: 100mV TIME/DIV: 1mS
5
IC11 Pin ª (SLD)
VOLT/DIV: 200mV TIME/DIV: 2S
VREF VREF
3
IC11 Pin % (TO)
VOLT/DIV: 100mV TIME/DIV: 1mS
VREF
13
14
IC DESCRIPTION IC, LA9241M
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Pin Name FIN2 FIN1 E F TB TE TE TESI SCI TH TA TD TD JP TO FD FD I/O I I I I I I O I I I O I I I O O I Description Pin to which external pickup photo diode is connected. RF signal is created by adding with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal. Pin to which external pickup photo diode is connected. Pin to which external pickup photo diode is connected. TE signal is created by subtracting from the F pin signal. Pin to which external pickup photo diode is connected. DC component of the TE signal is input. Pin to which external resistor setting the TE signal gain is connected between the TE pin. TE signal output pin. TES "Track Error Sense" comparator input pin. TE signal is passed through a bandpass filter then input. Shock detection signal input pin. Tracking gain time constant setting pin. TA amplifier output pin. Pin to which external tracking phase compensation constants are connected between the TD and VR pins. Tracking phase compensation setting pin. Tracking jump signal (kick pulse) amplitude setting pin. Tracking control signal output pin. Focusing control signal output pin. Pin to which external focusing phase compensation constants are connected between the FD and FA pins. 18 FA I Pin to which external focusing phase compensation constants are connected between the FD and FA pins. 19 20 21 22 23 24 25 26 27 28 29 30, 31 32, 33 34 35 FA FE FE AGND NC SP SPG SP SPD SLEQ SLD SL, SL+ JP, JP+ TGL TOFF I O I -- -- O I I O I O I I I I Pin to which external focusing phase compensation constants are connected between the FA and FE pins. FE signal output pin. Pin to which external FE signal gain setting resistor is connected between the FE pin. Analog signal GND. No connection. Single ended output of the CV+ and CV pin input signal. Pin to which external spindle gain setting resistor in 12 cm mode is connected. Pin to which external spindle phase compensation constants are connected together with SPD pin. Spindle control signal output pin. Pin to which external sled phase compensation constants are connected. Sled control signal output pin. Sled advance signal input pin from microprocessor. Tracking jump signal input pin from DSP. Tracking gain control signal input from DSP. Low gain when TGL = H. Tracking off control signal input pin from DSP. Off when TOFF = H.
15
Pin No. 36 37 38 39, 40 41 42
Pin Name TES HFL SLOF CV, CV+ RFSM RFS
I/O O O I I O I
Description Pin from which TES signal is output to DSP. "High Frequency Level" is used to judge whether the main beam position is on top of bit or on top of mirror. Sled servo off control input pin. CLV error signal input pin from DSP. RF output pin. RF gain setting and EFM signal 3T compensation constant setting pin together with RFSM pin.
43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
SLC SLI DGND FSC TBC NC DEF CLK CL DAT CE DRF FSS VCC2 REFI VR LF2 PH1 BH1 LDD LDS VCC1
O I -- O I -- O I I I I O I -- -- O I I I O I --
"Slice Level Control" is the output pin which controls the RF signal data slice level by DSP. Input pin which control the data slice level by the DSP. Digital system GND. Output pin to which external focus search smoothing capacitor is connected. "Tracking Balance Control" EF balance variable range setting pin. No connection. Disc defect detector output pin. Reference clock input pin. 4.23 MHz of the DSP is input. Microprocessor command clock input pin. Microprocessor command data input pin. Microprocessor command chip enable input pin. "Detect RF" RF level detector output. "Focus Search Select" focus search mode (± search/+ search) select pin. Servo system and digital system Vcc pin. Pin to which external bypass capacitor for reference voltage is connected. Reference voltage output pin. Disc defect detector time constant setting pin. Pin to which external capacitor for RF signal peak holding is connected. Pin to which external capacitor for RF signal bottom holding is connected. APC circuit output pin. APC circuit input pin. RF system Vcc pin.
16
IC, LC78622ED
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12, 13 14 15 16 17 18 19, 20 21 22 23 Pin Name DEFI TAI PDO VVSS ISET VVDD FR VSS EFMO EFMIN TEST2 CLV+, CLV
___
I/O I I O -- I -- I -- O I I O O I I O O O O O -- For PLL.
Description Defect sense signal (DEF) input pin. (Connect to 0V when not used). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Phase comparator output pin to control external VCO. GND pin for built-in VCO. Be sure to connect to 0V. Pin to which external resistor adjusting the PD0 output current. Power supply pin for built-in VCO. Pin for VCO frequency range adjustment. Digital system GND. Be sure to connect to 0V. For slice level control. EFM signal output pin. EFM signal input pin. Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Disc motor control output. Three level output is possible using command. Rough servo or phase control automatic selection monitoring output pin. Rough servo at H. Phase servo at L.
V/P HFL TES TOFF TGL JP+, JP PCK FSEQ VDD
Track detect signal input pin. Schmidt input. Tracking error signal input pin. Schmidt input. Tracking OFF output pin. Tracking gain selection output pin. Gain boost at L. Track jump control signal output pin. Three level output is possible using command. EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in. Sync signal detection output pin. H when the sync signal which is detected from EFM signal and thesync signal which is internally generated agree. Digital system power supply pin. The pin is controlled by the serial data command from microprocessor. When
24-28
SL+ - PUIN
I/O
General purpose input/output pin 1 to 5.
the pin is not used, set the pin to the input terminal and connect to 0V, or alternately set the pin to output terminal and leave the pin open.
29 30 31 32, 33 34 35 36 37 38 39 40 41 42
EMPH C2F DOUT TEST3, TEST4 N.C. MUTEL LVDD LCHO LVSS RVSS RCHO RVDD MUTER
O O O I -- O -- O -- -- O -- O
De-emphasis monitor output pin. De-emphasis disc is being played back at H. C2 flag output pin. DIGITAL OUT output pin. (EIAJ format). Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Not used. Set the pin to open. L-channel mute output pin. L-channel 1-bit DAC. L-channel power supply pin. L-channel output pin. L-channel GND. Be sure to connect to 0V. R-channel GND. Be sure to connect to 0V. R-channel 1-bit DAC. R-channel output pin. R-channel power supply pin. R-channel mute output pin.
17
Pin No. 43 44 45 46 47 48 49 50 51
Pin Name XVDD XOUT XIN XVSS SBSY EFLG PW SFSY SBCK
I/O -- O I -- O O O O I Crystal oscillator power supply pin.
Description
Pin to which external 16.9344 MHz crystal oscillator is connected. Crystal oscillator GND pin. Be sure to connect to 0V. Subcode block sync signal output pin. C1, C2, single and dual correction monitoring pin. Subcode P, Q, R, S, T, U and W output pin. Subcode frame sync signal output pin. Falls down when subcode enters standby. Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not in use.)
52 53 54 55 56 57 58 59 60 61 62 63 64
FSX WRQ RWC SQOUT COIN
___________
O O I O I I I O O O I I I
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of crystal oscillator. Subcode Q output standby output pin. Read/write control input pin. Schmidt input. Subcode Q output pin. Command input pin from microprocessor. Command input read clock or subcode read input clock from SQOUT pin LC78622 reset input pin. Set this pin to L once when the main power is turned on. Test signal output pin. Use this pin as open (normally L output). 16.9344 MHz output pin. 4.2336 MHz output pin. Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V while it is not controlling.
CQCK
________
RES TST11 16M 4.2M TEST5
______
CS TEST1
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
Note: The same potential must be applied to the respective power supply terminals. (VDD, VVDD, LVDD, RVDD, XVDD)
18
TEST MODE
1. How to Activate CD Test Mode Insert the AC plug while pressing the function CD button. All FL display tubes will light up, and the test mode will be activated. 2. How to Cancel CD Test Mode Either one of the following operations will cancel the CD test mode. · Press the function button. · Press the power switch button. (except CD function button) · Disconnect the AC plug
3. CD Test Mode Functions When test mode is activated, the following mode functions from No.1 to No.5 can be used by pressing the operation keys. Mode/No. Start mode No.1 Search mode Operation Activation 9 key FL display All lamps light Operation Test mode is activated. CD block power is ON. Laser diode turns always ON. Continual focus search (The pickup lens repeats the fullswing up-down motion.) * Avoid continual searches that last for more than 10 minutes. · · · · Contents · FL display check (All displays light.)
No.2 Play mode No.3 Traverse mode
1 2 key
;
key
No.4 Sled mode
fi key fl
All lamps light
No.5
· APC circuit check · Laser current measurement (Laser current control. Across a resistor connected between emitter and GND.) FOCUS SERVO · Check focus search waveform · Check focus error waveform (FOK/FZC are not monitored in the search mode) * NOTE 1 · Normal playback FOCUS SERVO/TRACKING SERVO · Focus search is continued if TOC CLV SERVO/SLED SERVO cannot be read. * NOTE 1 Check DRF · During normal disc playback TRACKING SERVO ON/OFF Press once; tracking servo OFF Tracking balance (traverse) check Press twice; tracking servo ON * NOTE 2 · Pickup moves to the outermost track SLED SERVO · Pickup moves to the innermost track Check SLED mechanism operation * NOTE 3 (During playback, machine operates normally.)
* NOTE 1: There are cases when the tracking servo cannot be locked owing to the protection circuit being operated when heat builds up in the driver IC if the focus search is operated continually for more than 10 minutes. In these cases the power supply should be switched off for 10 minutes until heat has been reduced and then re-started. * NOTE 2: Do not press the fi or fl keys when the machine is in the ; status is active. If they are pressed, playback will not be possible after the ; status has been canceled. If the fi or fl keys are pressed in the ; status, press the 9 key and return to the start mode (No.1). * NOTE 3: When pressing the fi or fl keys, take care to avoid damage to the gears. Because the sled motor is activated when the fi or fl keys are pressed, even when the pick-up is at the outermost or innermost track. 4. Operation Outline The operation of each mode is carried out in the direction of the arrows from the start mode as indicated in the following illustration. No. 2 Search mode
1 2
No. 3 Play mode
9 9
No. 1 Start mode (All FLs light up.)
1 2
2
9
fi fl
; ;
9
No. 5 Sled mode
No. 4 Traverse mode
;
If the DISC DIRECT PLAY button is pressed, the machine performs the same operation as the PLAY button is pressed as shown. If the tray is opened by pressing OPEN/CLOSE button during Play mode or Traverse mode, the machine returns to the Start mode. 19
ELECTRICAL ADJUSTMENT
3CD C.B (PATTERN SIDE)
R46
TP3 (VREF)
58
IC11 TP1 (TE) R16
41
1
SFR101
TP2 (RF)
20
Note: · Connect a probe (10: 1) of the oscilloscope test point for adjustment. · Connect ground (-) terminal of oscilloscope probe to TP3 (VREF) for all adjustment. 1. Focus Bias Adjustment Make the focus bias adjustment when replacing and repairing the optical block. Oscilloscope (DC range)
2. Tracking Balance Check Oscilloscope (DC range)
TP1 (TE) TP3 (VREF)
+
TP2 (RF) TP3 (VREF)
+
1) Connect an oscilloscope to test points TP1 (TE) and TP3 (VREF). 2) Start up the CD test mode. 3) Insert the test disc TCD-782 (YEDS-18) and enter the traverse mode of the CD test mode. 4) Confirm that the traverse waveform on an oscilloscope is vertically symmetrical as shown in the figure below. 5) After confirming the waveform, release the CD test mode.
1) Connect an oscilloscope to test points TP2 (RF) and TP3 (VREF). 2) Turn on the power switch. 3) Insert test disc TCD-782 (YEDS-18) and play back the second program. 4) Adjust SFR101 so that RF signal of the test point TP2 (RF) is MAX and CLEARREST.
A VREF B A=B VOLT/DIV: 20mV TIME/DIV: 1mS
MAX 1.4±0.1 Vp-p 0V EYE PATTERN must be CLEAR and MAX. VOLT/DIV: 0.5V TIME/DIV: 0.5µS Note: The current of the laser signal can be checked with the voltages on both sides of R46 (voltage across 10). The difference for the specified value shown on the label must be within ± 6.0mA.
KSS-213B 15165 SG442
44.2mA
Laser current Iop =
Voltage across R46 10
21
MECHANICAL EXPLODED VIEW 1/1
15
A
17
A
12 3 11 21 20 18 B
4 19
7 26 P.C.B
14 B 24 CHAS,MECHA 22 C 1 28 13 A 16 8
23 9
A
6 29 30
2 27
P.C.B
10 2 25 P.C.B C C HLDR,MECHA
3ZG-2 E1 3ZG-2 E3 3ZG-2 E4 KSM-2131FAM
CUSH CD A 5
22
MECHANICAL PARTS LIST 1/1
REF. NO 1 2 2 3 4
KANRI DESCRIPTION NO. 84-ZG1-239-210 PULLY,WORM N 84-ZG1-267-010 PULLEY,LOAD MO 8 81-ZG1-212-010 PULLY,LOAD MO 81-ZG1-239-010 S-SCREW,TT 81-ZG1-291-110 GEAR,TRAY RELAY NO3 S-SCREW MECH REAR HLDR,MAGNET J NAT HLDR,MAGNET JV HLDR,MAGNET NAT PLATE,MAGNET PLATE,MAGNET MK2 LVR,SW TRAY,NO2-B TRAY,NO3 MOTOR(BCH3B14) TURNTABLE,NO1(*) REFLECTOR,CD SPR-C,WORM LEVER,CAM LEVER,CAN 8 BELT,SQ1.8-117.7 SPR-E CAM S GEAR,MAIN CAM GEAR,MAIN CAM BLU SLIDE,MECHA CAM YEL SLIDER,MECHA CAM GEAR,TRAY (*) GEAR,RELAY GEAR,RELAY 8 PULLEY,RELAY
PART NO.
REF. NO 22 22 23 24 24
KANRI DESCRIPTION NO. 84-ZG1-221-010 GEAR,MAIN TT 84-ZG1-269-010 GEAR,MAIN TT 4 84-ZG1-238-010 GEAR,WORM N 84-ZG1-224-010 LEVER,TT 84-ZG1-288-010 LEVER,TT NAT BELT,SQ1.0-63.3 MAGNET,CLAMPER 4P MAGNET,CLAMPER 93ZZ MAGNET,CLAMPER 97 MOTOR, RF-500TB DC-5V (2MA) SPR-P,WORM CABI,OPTICAL CABI,OPTICAL C LID,OPTICAL HLDR,MECHA NAT CHAS,MECHA NAT TAPPING SCREW, BVT2+3-10 BVT2+3-6 BLK
PART NO.
5 81-ZG1-271-010 6 84-ZG1-290-010 6 84-ZG1-295-010 6 84-ZG1-289-010 7 81-ZG1-229-110 7 81-ZG1-255-110 8 9 9 10 11 12 13 14 14 83-ZG3-213-010 84-ZG1-003-310 84-ZG1-008-210 87-045-364-010 84-ZG1-005-210 84-ZG1-011-010 84-ZG1-248-010 84-ZG1-208-210 84-ZG1-266-010
25 84-ZG1-225-010 26 84-ZG1-300-010 26 84-ZG1-296-010 26 84-ZG1-268-010 27 87-045-305-010 28 84-ZG1-259-010 29 84-ZG1-244-310 29 84-ZG1-276-010 30 84-ZG1-261-010 31 84-ZG1-287-010 32 84-ZG1-286-010 A 87-067-703-010 C 87-067-981-010
15 84-ZG1-209-010 16 84-ZG1-211-010 17 84-ZG1-203-410 17 84-ZG1-215-410 18 84-ZG1-216-310 18 84-ZG1-204-310 19 20 20 21 84-ZG1-205-210 84-ZG1-206-110 84-ZG1-274-010 84-ZG1-207-010
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color B Black C Cream D Orange G Green H Gray L Blue LT Transparent Blue N Gold P Pink R Red S Silver ST Titan Silver T Brown V Violet W White WT Transparent White Y Yellow YT Transparent Yellow LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange
23
CD MECHANISM EXPLODED VIEW 1/1 (3ZG-2 E1)
11 12
8 2
6
A A
A A 1
5 3
SW1 M1
4 M2
DRIVE C.B
CD MECHANISM PARTS LIST 1/1 (3ZG-2 E1)
REF. NO 1 2 3 4 5 6 8 11 12 A
PART NO.
KANRI NO.
DESCRIPTION
83-ZG2-243-110 83-ZG2-235-010 83-ZG2-205-210 83-ZG2-236-010 83-ZG2-240-010 87-A90-836-010 83-ZG2-233-010 83-ZG2-245-110 83-ZG2-250-010 87-261-032-210
CHAS ASSY,SHT GEAR,A3 GEAR,B GEAR MOTOR 3 SHAFT,SLIDE 3 PICKUP,KSS-213F TURN TABLE,A5 LEVER,SHUTTER SPR-E,SHT 2 SCREW V+2-3
24
CD MECHANISM EXPLODED VIEW 1/1 (3ZG-2 E3)
11 12
8 2
6
A A
A A 1
5 3
4
P.C.B
CD MECHANISM PARTS LIST 1/1 (3ZG-2 E3)
REF. NO 1 2 3 4 5 6 8 11 12 A
PART NO. 83-ZG2-243-210 83-ZG2-235-010 83-ZG2-205-210 83-ZG2-236-010 83-ZG2-253-010 87-A90-836-010 83-ZG2-227-210 83-ZG2-245-410 83-ZG2-250-110 87-261-032-210
KANRI NO.
DESCRIPTION
CHAS ASSY,SHT GEAR,A3 GEAR,B GEAR MOTOR 3 SHAFT,SLIDE 5 PICKUP,KSS-213F TURN TABLE,C1 LEVER,SHUTTER SPR-E,SHT 2 SCREW V+2-3
25
CD MECHANISM EXPLODED VIEW 1/1 (3ZG-2 E4)
11 12
8 2
6
A A
A A 1
5 3
4
P.C.B
CD MECHANISM PARTS LIST 1/1 (3ZG-2 E4)
REF. NO 1 2 3 4 5 6 8 11 12 A
PART NO.
KANRI NO.
DESCRIPTION
83-ZG2-251-010 83-ZG2-235-010 83-ZG2-205-210 83-ZG2-236-010 83-ZG2-253-010 87-A90-836-010 83-ZG2-227-210 83-ZG2-245-410 83-ZG2-250-110 87-261-032-210
CHAS ASSY,SHT GEAR,A3 GEAR,B GEAR MOTOR 3 SHAFT,SLIDE 5 PICKUP,KSS-213F TURN TABLE,C1 LEVER,SHUTTER SPR-E,SHT 2 SCREW V+2-3
26
CD MECHANISM EXPLODED VIEW 1/1 (KSM-2131 FAM)
2
COVER 11 12 8
6
A
SPINDLE MOTOR (M3)
1
7
MOTOR C.B
CD MECHANISM PARTS LIST 1/1 (KSM-2131 FAM)
REF. NO 1 2 6 7 8
KANRI DESCRIPTION NO. 9X-262-629-220 MOTOR CHASSIS ASSY(MB)(FR) 92-626-907-010 GEAR(A)(S) 87-A90-836-010 OPTICAL PICK UP KSS-213F 92-626-908-020 SHAFT SLED 92-627-003-010 GEAR(B) LENS SHUTTER(F) SPRIG EXTENSION SCREW+P2-3
PART NO.
11 92-646-697-020 12 92-646-702-010 A 97-621-255-150
27
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
931261 Printed in Singapore