Text preview for : M31d Engine Cooling.pdf part of Daewoo Matiz Service Manual, Wiring Diagram - 16 Part File - 62 File



Back to : 796cc (My 2003).part01.ra | Home

SECTION 1D

ENGINE COOLING
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise noted.

TABLE OF CONTENTS
Description and Operation . . . . . . . . . . . . . . . . . . General Description . . . . . . . . . . . . . . . . . . . . . . . Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Surge Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Coolant Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric Cooling Fan . . . . . . . . . . . . . . . . . . . . . . . Engine Coolant Temperature Sensor . . . . . . . . . 1D-2 1D-2 1D-2 1D-2 1D-3 1D-3 1D-3 1D-4 Cooling System Diagnosis . . . . . . . . . . . . . . . . . . Repair Instructions . . . . . . . . . . . . . . . . . . . . . . . . . On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . . . . . Draining and Refilling the Cooling System . . . . Surge Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric Cooling Fan . . . . . . . . . . . . . . . . . . . . . . Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermostat (Typical) . . . . . . . . . . . . . . . . . . . . . . 1D-8 1D-9 1D-9 1D-9

1D-10 1D-11 1D-11 1D-12

Coolant Temperature Sensor . . . . . . . . . . . . . . . . 1D-4 Component Locator . . . . . . . . . . . . . . . . . . . . . . . . 1D-5 Coolant Hose and Components . . . . . . . . . . . . . 1D-5 Radiator/Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnostic Information and Procedure . . . . . . . Coolant Leaks Test . . . . . . . . . . . . . . . . . . . . . . . . Surge Tank Cap Test . . . . . . . . . . . . . . . . . . . . . . . 1D-6 1D-7 1D-7 1D-7

Thermostat (Euro III) . . . . . . . . . . . . . . . . . . . . . . 1D-13 Coolant Temperature Sensor . . . . . . . . . . . . . . . 1D-14 Engine Coolant Temperature Sensor . . . . . . . . 1D-15 Coolant Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Specifications . . . . . . . . . . . . . . . . . . . . Fastener Tightening Specifications . . . . . . . . . . 1D-15 1D-17 1D-17 1D-18

Thermostat Test . . . . . . . . . . . . . . . . . . . . . . . . . . . 1D-7

DAEWOO M-150 BL2

1D ­ 2 ENGINE COOLING

DESCRIPTION AND OPERATION
GENERAL DESCRIPTION
The cooling system maintains the engine temperature at an efficient level during all engine operating conditions. When the engine is cold the cooling system cools the engine slowly or not at all. This slow cooling of the engine allows the engine to warm up quickly. The cooling system includes a radiator(a) and cooling fan(b), a thermostat and housing(c), a coolant pump(d), a coolant pump drive belt and coolant hose. The timing belt drives the coolant pump. All components must function properly in order for the cooling system to operate. The coolant pump draws the coolant from the radiator. The coolant then circulates through water jackets in the engine block and the cylinder head, distributor case(e), throttle body(f). When the coolant reaches the operating temperature of the thermostat, the thermostat opens. The coolant then goes back to the radiator where it cools. This system directs some coolant through the hoses to the heater core(g). This provides for heating and defrosting. The surge tank(h) is connected to the radiator and throttle body to recover the coolant displaced by expansion from the high temperatures. The surge tank maintains the correct coolant level. The cooling system for this vehicle has no radiator cap and drain cock. The coolant is added to the cooling system through the surge tank. To drain the cooling system, disconnect the lower radiator hose and drain the coolant.

RADIATOR
This vehicle has a lightweight tube-and-fin aluminum radiator.

SURGE TANK
The surge tank is a transparent plastic reservoir, similar to the windshield washer reservoir. The surge tank is connected to the radiator and throttle body by a hose. As the vehicle is driven, the engine coolant heats and expands. The portion of the engine coolant displaced by this expansion flows from the radiator into the surge tank. The air trapped in the radiator is degassed into the surge tank. When the engine is stops, the engine coolant cools and contracts. The displaced engine coolant is then drawn back into the radiator. This keeps the radiator filled with the coolant to the desired level at all times and increases the cooling efficiency. Maintain the coolant level between the MIN and the MAX marks on the surge tank when the system is cold.

D102D001

DAEWOO M-150 BL2

ENGINE COOLING 1D ­ 3

COOLANT PUMP
The belt-driven centrifugal coolant pump consists of an impeller, a drive shaft, and a belt pulley. The impeller is supported by a completely sealed bearing. The coolant pump is serviced as an assembly and, therefore, cannot be disassembled.

THERMOSTAT
A wax pellet-type thermostat controls the flow of the engine coolant through the engine cooling system. The thermostat(i) is mounted in the thermostat housing. The thermostat stops the flow of the engine coolant from the engine to the radiator in order to provide faster warm-up, and to regulate the coolant temperature. The thermostat remains closed while the engine coolant is cold, preventing circulation of the engine coolant through the radiator. At this point, the engine coolant is allowed to circulate only throughout the heater core to warm it quickly and evenly. As the engine warms, the thermostat opens. This allows the engine coolant to flow through the radiator, where the heat is dissipated through the radiator. This opening and closing of the thermostat permits enough engine coolant to enter the radiator to keep the engine within proper engine temperature operating limits. The wax pellet in the thermostat is hermetically sealed in a metal case(j). The wax element of the thermostat expands when it is heated and contracts when it is cooled. As the vehicle is driven and the engine warms, the engine coolant temperature increases. When the engine coolant reaches a specified temperature, the wax pellet element in the thermostat expands and exerts pressure against the metal case, forcing the valve open. This allows the engine coolant to flow through the engine cooling system and cool the engine. As the wax pellet cools, the contraction allows a spring to close the valve. The thermostat begins to open at 82_C (180_F) and is fully open at 95_C (203_F). The thermostat closes at 80_C (176_F).

D102D002

ELECTRIC COOLING FAN
Caution: Keep hands, tools, and clothing away from the engine cooling fans to help prevent personal injury. This fan is electric and can turn ON whether or not the engine is running. Caution: If a fan blade is bent or damaged in any way, no attempt should be made to repair or reuse the damaged part. A bent or damaged fan assembly should always be replaced with a new one. The cooling fans are mounted behind the radiator in the engine compartment. The electric cooling fans increase the flow of air across the radiator fan and across the condenser on air conditioner (A/C)-equipped vehicles. This helps to speed cooling when the vehicle is at idle or moving at low speeds.

D102D003

DAEWOO M-150 BL2

1D ­ 4 ENGINE COOLING
The main fan size is 320 mm (12.6 in.) in diameter with seven blades(k) to aid the air flow through the radiator and the condenser. An electric motor(l) attached to the radiator support drives the fan. A/C OFF or Non-A/C Model D The cooling fan is actuated by the electronic control module (ECM) using a low speed cooling fan relay and a high speed cooling fan relay. On A/C equipped vehicles, a series/parallel cooling fan relay is also used. D The ECM will turn the cooling fan on at low speed when the coolant temperature reaches 93_C (199_F) and high speed at 100_C (212_F). D The ECM will change the cooling fan from high speed to low speed at 97_C (207_F) and turn the cooling fans off at 90_C (194_F). A/C ON D The ECM will only turn the cooling fan on at high speed when the A/C system is on regardless of any condition.
D102D004

COOLANT TEMPERATURE SENSOR
The coolant temperature sensor(m) controls the instrument panel temperature indicator. The coolant temperature sensor is located on the distributor case with the ECT sensor on an SOHC engine.

ENGINE COOLANT TEMPERATURE SENSOR
The engine coolant temperature (ECT) sensor (n) uses a thermistor to control the signal voltage to the engine control module (ECM).

DAEWOO M-150 BL2

ENGINE COOLING 1D ­ 5

COMPONENT LOCATOR
COOLANT HOSE AND COMPONENTS

D12D4011

1 2 3 4 5 6 7 8 9 10

Radiator Coolant Return Hose Upper Radiator Hose Not Used Radiator Assembly Lower Radiator Hose Throttle Body Assembly Surge Tank hose Surge Tank Coolant Temperature Sensor Engine Coolant Temperature Sensor

11 12 13 14 15 16 17 18 19 20

Surge Tank Return Hose Water Inlet Cap Heater Outlet Hose Heater Inlet Hose Distributor Case Thermostat Thermostat Housing Throttle Body Inlet Hose Throttle Body Outlet Hose Hose Bracket

DAEWOO M-150 BL2

1D ­ 6 ENGINE COOLING

RADIATOR/FAN

D12D4021

1 Radiator Assembly

2 Electric Cooling Fan Assembly

DAEWOO M-150 BL2

ENGINE COOLING 1D ­ 7

DIAGNOSTIC INFORMATION AND PROCEDURE
COOLANT LEAKS TEST
1. Remove the surge tank cap after the engine cools. 2. Check the coolant level. 3. Install a suitable cooling system pressure tester(b) to the surge tank filler neck using the adapter(a) and pressurize (110­120 kPa (16.0­17.4 psi)). 4. Check the coolant leaks on the hoses and connections during 2 minutes. 5. If the leak is checked, replace the parts or repair the connections.

D102D302

THERMOSTAT TEST
1. Remove the thermostat(f) from the vehicle. Refer to"Thermostat" in this section. 2. Make sure the valve spring is tight when the thermostat is fully closed. If the spring is not tight, replace the thermostat. 3. Suspend the thermostat and a thermometer in a pan of 50/50mixture of ethylene glycol and water. Do not let the thermostat or the thermometer rest on the bottom of the pan because the uneven concentration of heat on the bottom could result in inaccurate temperature measurements. 4. Heat the pan on a burner. 5. Use the thermometer to measure the temperature of the heated solution. 6. The thermostat should begin to open at 82°C (180°F) and it should be fully open at 95°C (203.4°F) and it should be fully close at 80°C (176.4°F). If it does not open or close at these temperature, replace the thermostat. Also, the thermostat rod's stroke from the initially open to the fully open should be 8mm (0.31 in.).

D102D301

SURGE TANK CAP TEST
The surge tank cap(c) is equipped with the pressure valve(d) and the vacuum valve(e). Therefore, the surge tank cap maintains proper pressure. And The surge tank cap protects the system from high-pressure by opening a pressure valve, and protects the coolant hoses from collapsing because of a vacuum. 1. Wash any sludge from the surge tank cap and the valve seat of the vacuum pressure valve for the surge tank cap. 2. Check for any damage or deformity to the vacuum pressure valve for the surge tank cap. If any damage or deformity is found, replace the cap. 3. Install a suitable cooling system pressure tester(b) to the cap using the Adapter(a). 4. Pull the vacuum pressure valve to the open position. If the surge tank cap does not seal properly, replace the surge tank cap. 5. Pressurize the cap to 90 to 120kPa (13 to 17psi). 6. Wait 10 seconds and check the pressure held by the tank cap tester. 7. If the pressure held by the cooling system pressure tester falls below 80kPa (11.6psi) replace the surge tank cap.

D102D303

DAEWOO M-150 BL2

1D ­ 8 ENGINE COOLING

COOLING SYSTEM DIAGNOSIS

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á
Condition Probable Cause Correction Engine Overheats D A loss of the coolant. D Add the coolant. D A weak coolant solution. D Confirm that the coolant solution is a 50/50 mixture of ethylene glycol and water. D Clean the front of the radiator. D Replace any damaged components. D Any dirt, any leaves, or any insects on the front of the radiator. D The leakage from the hoses, the coolant pump, the heater, the thermostat housing, the radiator, the heater core, or the head gasket. D A faulty thermostat. D Retarded ignition timing. D Replace a damaged thermostat. D Perform an ECM code diagnosis. D Confirm the integrity of the timing belt. D Replace the electric cooling fan. D Replace any damaged radiator hoses. D Replace a faulty water pump. D Replace a faulty surge tank cap. D Repair the damaged cylinder head or the damaged engine block. D Replace a faulty radiator. D Replace a damaged radiator. D Replace the surge tank or the hose. D Reseat the hoses. D Replace the hoses or the clamps. D Replace the coolant pump seal. D Replace the coolant pump gasket. D Tighten the cylinder head bolts to specifications. D Replace the cylinder head gasket, if needed. D Repair or replace any components, as needed to correct the leak. D Install a new thermostat of the correct type and heat range. D Add sufficient coolant to raise the fluid to the specified mark on the surge tank. D An improperly operating electric cooling fan. D Plugged or rotted radiator hoses. D A faulty water pump. D A faulty surge tank cap. D A cracked or plugged cylinder head or engine block. D A faulty radiator. Loss of Coolant D A leak in the radiator. D A leak in the surge tank or the hose. D Looseness or damage of radiator hoses, heater hoses, or connections. D Leaks in the coolant pump seal. D Leaks in the coolant pump gasket. D An improper cylinder head torque. D Leaks in the intake manifold, cylinder head gasket, heater core. Engine Fails to Reach Normal Operating Temperature or Cool Air from the Heater D Thermostat to be stuck open or to be wrong type. D The coolant level below the MIN mark on the surge tank.
DAEWOO M-150 BL2

ENGINE COOLING 1D ­ 9

REPAIR INSTRUCTIONS ON­VEHICLE SERVICE
DRAINING AND REFILLING THE COOLING SYSTEM
Caution: Do not remove the surge tank cap while the engine and the radiator are hot. Scalding fluid and steam may be blown out under pressure. 1. Place a pan below the vehicle to catch the draining coolant. 2. Drain the coolant. D Remove the surge tank cap (1). D Disconnect the lower radiator hose (2).
D12D5011

Caution: Dispose of the used coolant to a used coolant holding tank to be picked up with the used oil for disposal. Never pour the used coolant down the drain. Ethylene glycol antifreeze is an extremely toxic chemical. Disposing of it into the sewer system or the ground water can contaminate the local environment.

3. Connect the lower radiator hose. 4. Clean the cooling system. D Remove all sludge and dirt from inside the surge tank. And install the surge tank. Refer to "Surge Tank" in this section (1).

D102D502

DAEWOO M-150 BL2

1D ­ 10 ENGINE COOLING
D Add the clean water to the surge tank (2). 5. Run the engine until the thermostat opens. You can tell the thermostat is open when both radiator hoses are hot to the touch. 6. Stop the engine and disconnect the lower radiator hose to drain the coolant. 7. Repeat steps 3 through 6 until the drained water is clear and free of coolant and rust. Notice: Never use an antifreeze mixture more concentrated than 60 percent antifreeze to 40 percent water. The solution freezing point increases above this concentration.
D102D503

8. Fill the cooling system through the surge tank with a mixture of ethylene glycol antifreeze and water. The mixture must be at least 50 percent antifreeze, but not more than 60 percent antifreeze for cold weather operation. 9. Fill the surge tank to the specified MAX fill mark on the outside of the tank. 10. Install the surge tank cap.

SURGE TANK
Removal Procedure
Caution: To prevent personal injury, do not remove the surge tank cap while the engine and the radiator are hot, because the heat causes the system to remain under pressure scalding fluid and steam may be blown out under pressure. 1. Drain the engine coolant to below the level of the surge tank. 2. Remove the surge tank. D Loosen the overflow hose clamps and disconnect the overflow hoses from the surge tank (1). D Remove the surge tank (2). 3. Clean the inside and the outside of the surge tank and the surge tank cap with soap and water. 4. Rinse the surge tank and the cap thoroughly. 5. Check the surge tank and the cap for crack or other damage.

D102D504

DAEWOO M-150 BL2

ENGINE COOLING 1D ­ 11 Installation Procedure
1. Install the surge tank to the vehicle. D Install the surge tank with pressing down (1). D Connect the overflow hoses to the surge tank (2). 2. Secure the overflow hoses to the surge tank with the hose clamps. 3. Fill the surge tank with coolant to the MAX mark.

D102D505

ELECTRIC COOLING FAN
Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the electric cooling fan assembly. D Disconnect the cooling fan electrical connector (1). D Remove the bolts (2). D Remove the electric cooling fan assembly (3).

D102D506

Installation Procedure
3.5­4.5 NSm 1. Install the electric cooling fan assembly with the bolts.

Tighten
Tighten the bolts to 3.5­4.5 NSm (31­40 lb-in). 2. Connect the cooling fan electrical connector. 3. Connect the negative battery cable.

D12D507A

RADIATOR
Removal Procedure
1. Disconnect the negative battery cable. 2. Disconnect the lower radiator hose and drain the engine cooling system. Refer to "Draining and Refilling the Cooling System" in this section. 3. Disconnect the upper radiator hose and the surge tank hose. D Loosen the upper radiator hose clamp and disconnect the upper radiator hose (1). D Loosen the surge tank hose clamp and disconnect the surge tank hose (2).

D12D5081

DAEWOO M-150 BL2

1D ­ 12 ENGINE COOLING
4. Remove the electric cooling fan. Refer to "Electric Cooling Fan" in this section. 5. Remove the radiator. D Remove the bolts (1). D Remove the radiator support brackets (2). D Remove the radiator (3). 6. Check the radiator for breaking, clog or other damage. Important: The radiator still contains a substantial amount of coolant. Drain the remainder of the coolant from the radiator into a drain pan.
D12D5091

Installation Procedure
1. Install the radiator with the mounting bolts (1) and the support brackets (2).

Tighten
Tighten the support bracket bolts to 3.5­4.5 NSm (31­40 lb-in). 2. Install the electric cooling fan. Refer to "Electric Cooling Fan" in this section.

D12D5101

3. 4. 5. 6.

Connect the upper radiator hose to the radiator (1). Connect the surge tank hose to the radiator (2). Secure each hose with hose clamps. Refill the engine cooling system. Refer to "Draining and Refilling the Cooling System" in this section.

7. Connect the negative battery cable.

D12D5111

THERMOSTAT (TYPICAL)
Removal Procedure
Caution: To prevent personal injury, do not remove the surge tank cap while the engine and the radiator are hot because the heat causes the system to remain under pressure. Scalding fluid and steam may be blown out under pressure. 1. Remove air filter assembly. Refer to Section 1B, SOHC Engine Mechanical. 2. Disconnect the lower radiator hose and drain the coolant. Refer to "Drain and Refilling the Cooling System" 3. Disconnect the upper radiator hose.
DAEWOO M-150 BL2

D102D512

ENGINE COOLING 1D ­ 13
D Loosen the hose clamp (1). D Disconnect the upper radiator hose (2).

4. Remove the thermostat. D Remove the bolts (1). D Remove the thermostat housing (2). D Remove the thermostat with the gasket (3). 5. Check the gasket for crack or other damage. 6. Inspect the valve seat for foreign matter that could prevent the valve from seating properly. 7. Inspect the thermostat for proper operation. Refer to "Thermostat Test" in this section.

D102D513

Installation Procedure
1. Install the thermostat with the bolts and the thermostat housing. 8­15 NSm

Tighten
Tighten the mounting bolts to 8­15 NSm (71­130 lb-in). 2. Secure the upper radiator hose to the thermostat housing with a hose clamp. 3. Refill the engine cooling system. Refer to "Draining and Refilling the Cooling System" in this section.

D12D514A

THERMOSTAT (EURO III)
Removal Procedure
Caution: To prevent personal injury, do not remove the surge tank cap while the engine and the radiator are hot because the heat causes the system to remain under pressure. Scalding fluid and steam may be blown out under pressure. 1. Remove air filter assembly. Refer to Section 1B, SOHC Engine Mechanical. 2. Disconnect the lower radiator hose and drain the coolant. Refer to "Drain and Refilling the Cooling System" 3. Disconnect the upper radiator hose.

MAA1D010

DAEWOO M-150 BL2

1D ­ 14 ENGINE COOLING
4. Remove the thermostat. D Remove the bolts. D Remove the thermostat housing. D Remove the thermostat with the gasket. 5. Check the gasket for crack or other damage. 6. Inspect the valve seat for foreign matter that could prevent the valve from seating properly. 7. Inspect the thermostat for proper operation. Refer to "Thermostat Test" in this section.

MAA1D020

Installation Procedure
1. Install the thermostat with the bolts and the thermostat housing.

Tighten
Tighten the mounting bolts to 8­15 NSm (71­130 lb-in). 2. Secure the upper radiator hose to the thermostat housing with a hose clamp. 3. Refill the engine cooling system. Refer to "Draining and Refilling the Cooling System" in this section. 4. Install the air filter assembly. Refer to Section 1B, SOHC Engine Mechanical.

MAA1D011

COOLANT TEMPERATURE SENSOR
Removal Procedure
1. Disconnect the negative battery cable. 2. Disconnect the lower radiator hose and drain the coolant. Refer to "Draining and Refilling the Cooling System" in this section. 3. Remove the coolant temperature sensor. D Disconnect the electrical connector (1). D Remove the coolant temperature sensor (2).

D102D515

Installation Procedure
10 NSm 1. Install the coolant temperature sensor into the threaded hole in the intake manifold.

Tighten
Tighten the coolant temperature sensor to 10 NSm (89 lb-in). D Connect the electrical connector to the coolant temperature sensor (1). 2. Connect the lower radiator hose and refill the coolant. Refer to "Draining and refilling the cooling system" in this section. 3. Connect the negative battery cable.
DAEWOO M-150 BL2

D12D516A

ENGINE COOLING 1D ­ 15

ENGINE COOLANT TEMPERATURE SENSOR
Removal Procedure
1. Disconnect the negative battery cable. 2. Disconnect the lower radiator hose and drain the coolant "Draining and Refilling the Cooling System" in this section. 3. Remove the engine coolant temperature (ECT) sensor. D Disconnect the electrical connector (1). D Remove the ECT sensor (2).

D102D517

Installation Procedure
1. Install the ECT sensor. 20 NSm

Tighten
Tighten the ECT sensor to 20 NSm (15 lb-ft). D Connect the electrical connector to the ECT sensor (1). 2. Connect the lower radiator hose and refill the coolant. Refer to "Draining and Refilling the Cooling System" in this section. 3. Connect the negative battery cable.
D12D518A

COOLANT PUMP
Removal Procedure
1. Disconnect the negative battery cable. 2. Disconnect the lower radiator hose and drain the coolant. Refer to "Draining and Refilling the Cooling System" in this section. 3. Remove the timing belt. Refer to Section 1B, Engine Mechanical. 4. Remove the rear timing belt cover. D Remove the bolts (1). D Remove the rear timing belt cover (2). 5. Remove the coolant pump. D Remove the nuts (1). D Remove the bolts (2). D Remove the coolant pump (3). D Remove the gasket. Notice: Remove the coolant pump as shown figure (a).

D102B533

D102D519

DAEWOO M-150 BL2

1D ­ 16 ENGINE COOLING Installation Procedure
9­12 NSm 1. Install the coolant pump with the new gasket.

Tighten
Tighten the bolts and the nuts to 9­12 NSm (80­106 lb-in) (a).

D12D520A

2. Install the rear timing belt cover. 9­12 NSm

Tighten
Tighten the bolts to 9­12 NSm (80­106 lb-in) (b). 3. Install the timing belt. Refer to Section 1B, Engine Mechanical. 4. Connect the lower radiator hose and drain the coolant. Refer to "Draining and Refilling the Cooling System" in this section. 5. Connect the negative battery cable.

D12D521A

DAEWOO M-150 BL2

ENGINE COOLING 1D ­ 17

SPECIFICATIONS
GENERAL SPECIFICATIONS
Application Cooling System Coolant Cooling Type Coolant Capacity Thermostat Type Temperature(opened initially) Thermostat Temperature(perfectly opened) Temperature(perfectly closed) Stroke(perfectly opened) Cooling Fan Type Blade Number Cooling Fan Diameter Electric Cooling Fan Temperature At Low Speed ON Temperature At Low Speed OFF Temperature At High Speed ON Temperature At High Speed OFF Surge Tank Open Pressure of The Pressure Valve Open Pressure of The Vacuum Valve Water Pump Type Coolant Pump Impeller Diameter Impeller Blade Number Radiator Type Radiator Core Width Core Height Core Depth (Standard/Heavy Duty) Resistance (Coolant Temperature 50°C(122.4°F)) Coolant Temperature Sensor Resistance (Coolant Temperature 85°C(185.4°F)) Resistance (Coolant Temperature 105°C(221.4°F)) Engine Coolant Temperature Sensor Resistance (Coolant Temperature 20°C(68.4°F)) Resistance (Coolant Temperature 80°C(176.4°F)) Description Unit ­ L/qt ­ °C(°F) °C(°F) °C(°F) mm(in.) ­ EA mm(inch) °C(°F) °C(°F) °C(°F) °C(°F) kPa (psi) kPa (psi) ­ mm(in.) EA ­ mm(in.) mm(in.) mm(in.) Standard Forced Water Circulation 3.8/4.00 Pellet Type 82(180) 95(203.4) 80(176.4) 8 (0.32) Electric 6 300(11.8) 93(199.8) 90(194.4) 100(212.4) 97(207) 120­150 (17.4­21.8) 10 (1.5) Centrifugal 60(2.36) 7 Cross­Flow 458(18.03) 295(11.61) 16/27(0.63/1.06) 185.2 49.2 27.5 3,520 332 Limit

DAEWOO M-150 BL2

1D ­ 18 ENGINE COOLING

FASTENER TIGHTENING SPECIFICATIONS
Application Engine Coolant Temperature Sensor Coolant Temperature Sensor Coolant Pipe Bolt Electric Cooling Fan Motor Nut Electric Cooling Fan Assembly Bolt Distributor Case Bolt/Nut Radiator Mounting Bracket Bolt Thermostat Housing Bolt Water Inlet Cap Bolt Coolant Pump Bolt/Nut Coolant Pump Stud Bolt NSm 10 20 8 ­ 15 3.0 ­ 3.2 3.5 ­ 4.5 8 ­ 12 3.5 ­ 4.5 8 ­ 15 8 ­ 12 9­12 9­12 Lb-Ft ­ 15 ­ ­ ­ ­ ­ ­ ­ ­ ­ Lb-In 89 ­ 71 ­ 130 27 ­ 28 31 ­ 40 71 ­ 106 31 ­ 40 71 ­ 130 71 ­ 106 80 ­ 106 80 ­ 106

DAEWOO M-150 BL2