Text preview for : M31f1 Engine Controls 1-54.pdf part of Daewoo Matiz Service Manual, Wiring Diagram - 16 Part File - 62 File
Back to : 796cc (My 2003).part01.ra | Home
SECTION 1F
ENGINE CONTROLS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise noted.
TABLE OF CONTENTS
Description and Operation . . . . . . . . . . . . . . . . . . Ignition System Operation . . . . . . . . . . . . . . . . . . Electronic Ignition System Ignition Coil . . . . . . . Crankshaft Position Sensor . . . . . . . . . . . . . . . . . Camshaft Position Sensor . . . . . . . . . . . . . . . . . . Idle Air System Operation . . . . . . . . . . . . . . . . . . Fuel Control System Operation . . . . . . . . . . . . . . Evaporative Emission Control System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Controlled Charcoal Canister . . . . . . . . . . . . . . . . Positive Crankcase Ventilation Control System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine Coolant Temperature Sensor . . . . . . . . . Throttle Position Sensor . . . . . . . . . . . . . . . . . . . . Catalyst Monitor Oxygen Sensors . . . . . . . . . . . 1F-4 1F-4 1F-4 1F-4 1F-4 1F-4 1F-4 1F-5 1F-5 1F-5 1F-6 1F-6 1F-6 Diagnostic Information and Procedures . . . . System Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . Diagnostic Aids . . . . . . . . . . . . . . . . . . . . . . . . . . Idle Learn Procedure . . . . . . . . . . . . . . . . . . . . . Euro On-Board Diagnostic (EOBD) System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ECM Output Diagnosis . . . . . . . . . . . . . . . . . . . . Multiple ECM Information Sensor DTCs Set . . Engine Cranks But Will Not Run . . . . . . . . . . . . No Malfunction Indicator Lamp . . . . . . . . . . . . . Malfunction Indicator Lamp On Steady . . . . . . Fuel System Diagnosis . . . . . . . . . . . . . . . . . . . . Fuel Pump Relay Circuit Check . . . . . . . . . . . . Main Relay Circuit Check . . . . . . . . . . . . . . . . . . Manifold Absolute Pressure Check . . . . . . . . . . Idle Air Control System Check . . . . . . . . . . . . . Ignition System Check . . . . . . . . . . . . . . . . . . . . 1F-17 1F-17 1F-17 1F-17 1F-18 1F-20 1F-21 1F-25 1F-30 1F-32 1F-34 1F-36 1F-38 1F-40 1F-42 1F-45
Electric Exhaust Gas Recirculation Valve . . . . . 1F-6 Intake Air Temperature Sensor . . . . . . . . . . . . . . 1F-7 Idle Air Control Valve . . . . . . . . . . . . . . . . . . . . . . 1F-7 Manifold Absolute Pressure Sensor . . . . . . . . . . Engine Control Module . . . . . . . . . . . . . . . . . . . . . Fuel Injector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel Cutoff Switch (Inertia Switch) . . . . . . . . . . . Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Variable Reluctance (VR) Sensor . . . . . . . . . . . . Octane Number Connector . . . . . . . . . . . . . . . . . Strategy-Based Diagnostics . . . . . . . . . . . . . . . . 1F-7 1F-8 1F-8 1F-8 1F-8 1F-8 1F-8 1F-9
Engine Cooling Fan Circuit Check . . . . . . . . . . 1F-48 Data Link Connector Diagnosis . . . . . . . . . . . . . 1F-52 Fuel Injector Balance Test . . . . . . . . . . . . . . . . . 1F-54 Diagnostic Trouble Code Diagnosis . . . . . . . . 1F-55 Clearing Trouble Codes . . . . . . . . . . . . . . . . . . . 1F-55 Diagnostic Trouble Codes . . . . . . . . . . . . . . . . . 1F-55 DTC P0107 Manifold Absolute Pressure Sensor Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-58 DTC P0108 Manifold Pressure Sensor High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-62 DTC P0112 Intake Air Temperature Sensor Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-66 DTC P0113 Intake Air Temperature Sensor High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-68 DTC P0117 Engine Coolant Temperature Sensor Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-72 DTC P0118 Engine Coolant Temperature Sensor High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-74
EOBD Serviceability Issues . . . . . . . . . . . . . . . . . 1F-9 Serial Data Communications . . . . . . . . . . . . . . . 1F-10 Euro On-Board Diagnostic (EOBD) . . . . . . . . . 1F-10 Comprehensive Component Monitor Diagnostic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-11 Common EOBD Terms . . . . . . . . . . . . . . . . . . . . DTC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reading Diagnostic Trouble Codes . . . . . . . . . Primary System-Based Diagnostics . . . . . . . . 1F-11 1F-13 1F-13 1F-15
DAEWOO M-150 BL2
1F 2 ENGINE CONTROLS
DTC P0122 Throttle Position Sensor Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-76 DTC P0123 Throttle Position Sensor High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-80 DTC P0131 Oxygen Sensor Low Voltage . . . . 1F-84 DTC P0132 Oxygen Sensor High Voltage . . . . 1F-88 DTC P0133 Oxygen Sensor No Activity . . . . . 1F-90 DTC P0137 Heated Oxygen Sensor Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-94 DTC P0138 Heated Oxygen Sensor High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-98 DTC P0140 Heated Oxygen Sensor No Activity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-100 DTC P0141 Heated Oxygen Sensor Heater Malfunction . . . . . . . . . . . . . . . . . . . . 1F-104 DTC P0171 Fuel Trim System Too Lean . . . . 1F-106 DTC P0172 Fuel Trim System Too Rich . . . . 1F-109 DTC P1230 Fuel Pump Relay Low Voltage . 1F-114 DTC P1231 Fuel Pump Relay High Voltage . 1F-118 DTC P0261 Injector 1 Low Voltage . . . . . . . . 1F-122 DTC P0262 Injector 1 High Voltage . . . . . . . . 1F-124 DTC P0264 Injector 2 Low Voltage . . . . . . . . 1F-126 DTC P0265 Injector 2 High Voltage . . . . . . . . 1F-128 DTC P0267 Injector 3 Low Voltage . . . . . . . . 1F-130 DTC P0268 Injector 3 High Voltage . . . . . . . . 1F-132 DTC P0300 Multiple Cylinder Misfire . . . . . . . 1F-135 DTC P0300 Multiple Cylinder Misfire . . . . . . . 1F-139 DTC P1320 Crankshaft Segment Period Segment adaptation At Limit . . . . . . . . . . . . 1F-142 DTC P1321 Crankshaft Segment Period Tooth Error . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-144 DTC P0327 Knock Sensor Circuit Fault . . . . 1F-146 DTC P0335 Magnetic Crankshaft Position Sensor Electrical Error . . . . . . . . . . . . . . . . . 1F-150 DTC P0336 58X Crankshaft Position Sensor No Plausible Signal . . . . . . . . . . . . . . . . . . . . 1F-152 DTC P0337 58X Crankshaft Position Sensor No Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-154 DTC P0341 Camshaft Position Sensor Rationality . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-156 DTC P0342 Camshaft Position Sensor No Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-158 DTC P0351 Ignition Signal Coil A Fault . . . . . 1F-160 DTC P0352 Ignition Signal Coil B Fault . . . . . 1F-162 DTC P0353 Ignition Signal Coil C Fault . . . . . 1F-164 DTC P1382 Rough Road Data Invalid (Non ABS) . . . . . . . . . . . . . . . . . . . . . 1F-166 DTC P1382 Rough Road Data Invalid (ABS) 1F-170 DTC P1385 Rough Road Sensor Circuit Fault (Non ABS) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-174 DTC P1385 Rough Road Sensor Circuit Fault (ABS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-178 DTC P0400 Exhaust Gas Recirculation Out Of Limit . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-182 DTC P1402 Exhaust Gas Recirculation Blocked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-186 DTC P1403 Exhaust Gas Recirculation Valve Failure . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-188 DTC P0404 Exhaust Gas Recirculation Opened . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-192 DTC P1404 Exhaust Gas Recirculation Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-196 DTC P0405 EEGR Pintle Position Sensor Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-200 DTC P0406 EEGR Pintle Position Sensor High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-204 DTC P0420 Catalyst Low Efficiency . . . . . . . . 1F-208 DTC P0444 EVAP Purge Control Circuit No Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-210 DTC P0445 EVAP Purge Control Fault . . . . . 1F-214 DTC P0462 Fuel Level Sensor Low Voltage . 1F-218 DTC P0463 Fuel Level Sensor High Voltage 1F-222 DTC P0480 Low Speed Cooling Fan Relay Circuit Fauit (Without A/C) . . . . . . . . . . . . . . 1F-226 DTC P0480 Low Speed Cooling Fan Relay Circuit Fauit (With A/C) . . . . . . . . . . . . . . . . . 1F-230 DTC P0481 High Speed Cooling Fan Relay Circuit Fauit (Without A/C) . . . . . . . . . . . . . . 1F-234 DTC P0481 High Speed Cooling Fan Relay Circuit Fauit (With A/C) . . . . . . . . . . . . . . . . . 1F-238 DTC P0501 Vehicle Speed No Signal (M/T Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-242 DTC P1505 Idle Air Control Valve (IACV) Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-246 DTC P1535 Evaporator Temperature Sensor High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-250 DTC P1536 Evaporator Temperature Sensor Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-252 DTC P1537 A/C Compressor Relay High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-254 DTC P1538 A/C Compressor Relay Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-256 DTC P0562 System Voltage (Engine Side) Too Low . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-258 DTC P0563 System Voltage (Engine Side) Too High . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-260 DTC P0601 Engine Control Module Chechsum Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-262 DTC P0604 Engine Control Module Internal/ External RAM Error . . . . . . . . . . . . . . . . . . . . 1F-263 DTC P0605 Engin Control Module NMVY Write Error . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-264 DTC P1610 Main Relay High Voltage . . . . . . 1F-266 DTC P1611 Main Relay Low Voltage . . . . . . . 1F-268
DAEWOO M-150 BL2
ENGINE CONTROLS 1F 3
DTC P1628 Immobilizer No Successful Communication . . . . . . . . . . . . . . . . . . . . . . . 1F-270 DTC P1629 Immovilizer Wrong Computation 1F-272 DTC P0656 Fuel Level Gauge Circuit Fault . 1F-274 DTC P1660 Malfunction Indicator Lamp (MIL) High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-276 DTC P1661 Malfunction Indicator Lamp (MIL) Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-278 Symptom Diagnosis . . . . . . . . . . . . . . . . . . . . . . 1F-280 Important Preliminary Checks . . . . . . . . . . . . . 1F-280 Intermittent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-281 Hard Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-283 Surges or Chuggles . . . . . . . . . . . . . . . . . . . . . 1F-286 Lack of Power, Sluggishness or Sponginess 1F-288 Detonation/Spark Knock . . . . . . . . . . . . . . . . . . 1F-290 Hesitation, Sag, Stumble . . . . . . . . . . . . . . . . . 1F-292 Cuts Out, Misses . . . . . . . . . . . . . . . . . . . . . . . . 1F-294 Poor Fuel Economy . . . . . . . . . . . . . . . . . . . . . . 1F-296 Rough, Unstable, or Incorrect Idle, Stalling . . 1F-297 Excessive Exhaust Emissions or Odors . . . . 1F-300 Dieseling, Run-on . . . . . . . . . . . . . . . . . . . . . . . 1F-302 Backfire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-303 Maintenance and Repair . . . . . . . . . . . . . . . . . . 1F-304 On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . . 1F304 Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F304 Fuel Pressure Regulator . . . . . . . . . . . . . . . . . 1F-305 Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-306 Fuel Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1F-307 Fuel Rail and Injectors . . . . . . . . . . . . . . . . . . . 1F-308 Evaporator Emission Canister . . . . . . . . . . . . . 1F-309 Evaporator Emission Canister Purge Solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manifold Absolute Pressure (MAP) Sensor . . Throttle Body . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine Coolant Temperature (ECT) Sensor . Intake Air Temperature (ECT) Sensor . . . . . . Oxygen Sensor (O2S 1) . . . . . . . . . . . . . . . . . . Heated Oxygen Sensor (HO2S 2) . . . . . . . . . Electric Exhaust Gas Recirculation (EEGR) Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Knock Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic Ignition (EI) System Ignition Coil . Crankshaft Position (CKP) Sensor . . . . . . . . Camshaft Position (CMP) Sensor . . . . . . . . . . Engine Control Module (ECM) . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . Fastener Tightening Specification . . . . . . . . . . Special Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Tools Table . . . . . . . . . . . . . . . . . . . . . . Schematic and Routing Diagrams . . . . . . . . . ECM Wiring Diagram (Sirius D3 1 of 5) . . . . . . . . . . . . . . . . . . . . ECM Wiring Diagram (Sirius D3 2 of 5) . . . . . . . . . . . . . . . . . . . . ECM Wiring Diagram (Sirius D3 3 of 5) . . . . . . . . . . . . . . . . . . . . ECM Wiring Diagram (Sirius D3 4 of 5) . . . . . . . . . . . . . . . . . . . . ECM Wiring Diagram (Sirius D3 5 of 5) . . . . . . . . . . . . . . . . . . . . 1F-310 1F-310 1F-311 1F-312 1F-313 1F-314 1F-314 1F-315 1F-315 1F-316 1F-316 1F-317 1F-317 1F-319 1F-319 1F-319 1F-319 1F-320 1F-320 1F-321 1F-322 1F-323 1F-324
DAEWOO M-150 BL2
1F 4 ENGINE CONTROLS
DESCRIPTION AND OPERATION
IGNITION SYSTEM OPERATION
This ignition system does not use a conventional distributor and coil. It uses a crankshaft position sensor input to the Engine Control Module (ECM). The ECM then determines Electronic Spark Timing (EST) and triggers the electronic ignition system ignition coil. This type of distributorless ignition system uses a "waste spark'' method of spark distribution. Each cylinder is individural with coil per cylinder. These systems use the EST signal from the ECM to control the EST. The ECM uses the following information: D D D D Engine load (manifold pressure or vacuum). Atmospheric (barometric) pressure. Engine temperature. Intake air temperature. jection mode of operation. If the ECM detects an incorrect CMP signal while the engine is running, Diagnostic Trouble Code (DTC) P0341 will set. If the CMP signal is lost while the engine is running, the fuel injection system will shift to a calculated sequential fuel injection mode based on the last fuel injection pulse, and the engine will continue to run. As long as the fault is present, the engine can be restarted. It will run in the calculated sequential mode with a 1-in-6 chance of the injector sequence being correct.
IDLE AIR SYSTEM OPERATION
The idle air system operation is controlled by the base idle setting of the throttle body and the Idle Air Control (IAC) valve. The Engine Control Module (ECM) uses the IAC valve to set the idle speed dependent on conditions. The ECM uses information from various inputs, such as coolant temperature, manifold vacuum, etc., for the effective control of the idle speed.
D Crankshaft position. D Engine speed (rpm).
ELECTRONIC IGNITION SYSTEM IGNITION COIL
The Electronic Ignition (EI) system ignition coil is mounted near on the cylinder head. A terminals of the EI system ignition coil provides the spark for each spark plug. The EI system ignition coil is not serviceable and must be replaced as an assembly.
FUEL CONTROL SYSTEM OPERATION
The function of the fuel metering system is to deliver the correct amount of fuel to the engine under all operating conditions. The fuel is delivered to the engine by the individual fuel injectors mounted into the intake manifold near each cylinder. The main fuel control sensors are the Manifold Absolute Pressure (MAP) sensor, the oxygen sensor (O2S), and the heated oxygen sensor (HO2S). The MAP sensor measures or senses the intake manifold vacuum. Under high fuel demands, the MAP sensor reads a low vacuum condition, such as wide open throttle. The Engine Control Module (ECM) uses this information to enrich the mixture, thus increasing the fuel injector on-time, to provide the correct amount of fuel. When decelerating, the vacuum increases. This vacuum change is sensed by the MAP sensor and read by the ECM, which then decreases the fuel injector on-time due to the low fuel demand conditions. The O2S is located in the exhaust manifold. The HO2S is located in the exhaust pipe. The oxygen sensors indicate to the ECM the amount of oxygen in the exhaust gas, and the ECM changes the air/fuel ratio to the engine by controlling the fuel injectors. The best air/fuel ratio to minimize exhaust emissions is 14.7:1, which allows the catalytic converter to operate most efficiently. Because of the constant measuring and adjusting of the air/fuel ratio, the fuel injection system is called a "closed loop" system. The ECM uses voltage inputs from several sensors to determine how much fuel to provide to the engine. The
CRANKSHAFT POSITION SENSOR
This Electronic Ignition (EI) system uses a magnetic crankshaft position sensor. This sensor protrudes through its mount to within approximately 1.3 mm (0.05 inch) of the crankshaft reluctor. The reluctor is a special wheel attached to the crankshaft with 58 slots machined into it, 57 of which are equally spaced in 6-degree intervals. The last slot is wider and serves to generate a "sync pulse." As the crankshaft rotates, the slots in the reluctor change the magnetic field of the sensor, creating an induced voltage pulse. The longer pulse of the 58th slot identifies a specific orientation of the crankshaft and allows the Engine Control Module (ECM) to determine the crankshaft orientation at all times. The ECM uses this information to generate timed ignition and injection pulses that it sends to the ignition coils and to the fuel injectors.
CAMSHAFT POSITION SENSOR
The Camshaft Position (CMP) sensor sends a CMP signal to the Engine Control Module (ECM). The ECM uses this signal as a "sync pulse" to trigger the injectors in the proper sequence. The ECM uses the CMP signal to indicate the position of the #1 piston during its power stroke. This allows the ECM to calculate true sequential fuel in-
DAEWOO M-150 BL2
ENGINE CONTROLS 1F 5
fuel is delivered under one of several conditions, called "modes.''
Fuel Cut-Off Mode
No fuel is delivered by the fuel injectors when the ignition is off. This prevents dieseling or engine run-on. Also, the fuel is not delivered if there are no reference pulses received from the CKP sensor. This prevents flooding.
Starting Mode
When the ignition is turned ON, the ECM turns the fuel pump relay on for 2 seconds. The fuel pump then builds fuel pressure. The ECM also checks the Engine Coolant Temperature (ECT) sensor and the Throttle Position (TP) sensor and determines the proper air/fuel ratio for starting the engine. The ECM controls the amount of fuel delivered in the starting mode by changing how long the fuel injector is turned on and off. This is done by "pulsing'' the fuel injectors for very short times.
EVAPORATIVE EMISSION CONTROL SYSTEM OPERATION
The basic Evaporative Emission (EVAP) control system used is the charcoal canister storage method. This method transfers fuel vapor from the fuel tank to an activated carbon (charcoal) storage canister which holds the vapors when the vehicle is not operating. When the engine is running, the fuel vapor is purged from the carbon element by intake airflow and consumed in the normal combustion process. Gasoline vapors from the fuel tank flow into the tube labeled TANK. These vapors are absorbed into the carbon. The canister is purged by Engine Control Module (ECM) when the engine has been running for a specified amount of time. Air is drawn into the canister and mixed with the vapor. This mixture is then drawn into the intake manifold. The ECM supplies a ground to energize the controlled charcoal canister purge solenoid valve. This valve is Pulse Width Modulated (PWM) or turned on and off several times a second. The controlled charcoal canister purge PWM duty cycle varies according to operating conditions determined by mass airflow, fuel trim, and intake air temperature. Poor idle, stalling, and poor driveability can be caused by the following conditions: D An inoperative controlled canister purge valve. D A damaged canister. D Hoses that are split, cracked, or not connected to the proper tubes.
Run Mode
The run mode has two conditions called "open loop'' and "closed loop.''
Open Loop
When the engine is first started and it is above 400 rpm, the system goes into "open loop'' operation. In "open loop,'' the ECM ignores the signal from the O2S and calculates the air/fuel ratio based on inputs from the ECT sensor and the MAP sensor. The ECM stays in "open loop" until the following conditions are met: D The O2S has a varying voltage output, showing that it is hot enough to operate properly. D The ECT sensor is above a specified temperature. D A specific amount of time has elapsed after starting the engine.
Closed Loop
The specific values for the above conditions vary with different engines and are stored in the Electronically Erasable Programmable Read-Only Memory (EEPROM). When these conditions are met, the system goes into "closed loop" operation. In "closed loop," the ECM calculates the air/fuel ratio (fuel injector on-time) based on the signals from the oxygen sensors. This allows the air/fuel ratio to stay very close to 14.7 to 1.
Acceleration Mode
The ECM responds to rapid changes in throttle position and airflow and provides extra fuel.
CONTROLLED CHARCOAL CANISTER
The controlled charcoal canister is an emission control device containing activated charcoal granules. The controlled charcoal canister is used to store fuel vapors from the fuel tank. Once certain conditions are met, the Engine Control Module (ECM) activates the controlled charcoal canister purge solenoid, allowing the fuel vapors to be drawn into the engine cylinders and burned.
Deceleration Mode
The ECM responds to changes in throttle position and airflow and reduces the amount of fuel. When deceleration is very fast, the ECM can cut off fuel completely for short periods of time.
Battery Voltage Correction Mode
When battery voltage is low, the ECM can compensate for a weak spark delivered by the ignition module by using the following methods: D Increasing the fuel injector pulse width. D Increasing the idle speed rpm. D Increasing the ignition dwell time.
POSITIVE CRANKCASE VENTILATION CONTROL SYSTEM OPERATION
A Positive Crankcase Ventilation (PCV) control system is used to provide complete use of the crankcase va-
DAEWOO M-150 BL2
1F 6 ENGINE CONTROLS
pors. Fresh air from the air cleaner is supplied to the crankcase. The fresh air is mixed with blowby gases which then pass through a vacuum hose into the intake manifold. Periodically inspect the hoses and the clamps. Replace any crankcase ventilation components as required. A restricted or plugged PCV hose may cause the following conditions: D Rough idle D Stalling or low idle speed D Oil leaks D Oil in the air cleaner D Sludge in the engine A leaking PCV hose may cause the following conditions: D Rough idle D Stalling D High idle speed The ECM can determine fuel delivery based on throttle valve angle (driver demand). A broken or loose TP sensor can cause intermittent bursts of fuel from the injector and an unstable idle, because the ECM thinks the throttle is moving. A problem in any of the TP sensor circuits should set a Diagnostic Trouble Code (DTC) P0122 or P0123. Once the DTC is set, the ECM will substitute a default value for the TP sensor and some vehicle performance will return.
CATALYST MONITOR OXYGEN SENSORS
Three-way catalytic converters are used to control emissions of hydrocarbons (HC), carbon monoxide (CO), and oxides of nitrogen (NOx). The catalyst within the converters promotes a chemical reaction. This reaction oxidizes the HC and CO present in the exhaust gas and converts them into harmless water vapor and carbon dioxide. The catalyst also reduces NOx by converting it to nitrogen. The ECM can monitor this process using the oxygen sensor (O2S) and heated oxygen sensor (HO2S). These sensors produce an output signal which indicates the amount of oxygen present in the exhaust gas entering and leaving the three-way converter. This indicates the catalyst's ability to efficiently convert exhaust gasses. If the catalyst is operating efficiently, the O2S signals will be more active than the signals produced by the HO2S. The catalyst monitor sensors operate the same way as the fuel control sensors. The sensors' main function is catalyst monitoring, but they also have a limited role in fuel control. If a sensor output indicates a voltage either above or below the 450 mV bias voltage for an extended period of time, the Engine Control Module (ECM) will make a slight adjustment to fuel trim to ensure that fuel delivery is correct for catalyst monitoring. A problem with the O2S circuit will set DTC P0131, P0132, P0133 or P0134 depending on the special condition. A problem with the HO2S signal will set DTC P0137, P0138, P0140 or P0141 depending on the special condition. A fault in the heated oxygen sensor (HO2S) heater element or its ignition feed or ground will result in lower oxygen sensor response. This may cause incorrect catalyst monitor diagnostic results.
ENGINE COOLANT TEMPERATURE SENSOR
The Engine Coolant Temperature (ECT) sensor is a thermistor (a resistor which changes value based on temperature) mounted in the engine coolant stream. Low coolant temperature produces a high resistance (100,000 ohms at 40_C [40_F]) while high temperature causes low resistance (70 ohms at 130_C [266_F]). The Engine Control Module (ECM) supplies 5 volts to the ECT sensor through a resistor in the ECM and measures the change in voltage. The voltage will be high when the engine is cold and low when the engine is hot. By measuring the change in voltage, the ECM can determine the coolant temperature. The engine coolant temperature affects most of the systems that the ECM controls. A failure in the ECT sensor circuit should set a Diagnostic Trouble Code (DTC) P0117 or P0118. Remember, these DTC indicate a failure in the ECT circuit, so proper use of the chart will lead either to repairing a wiring problem or to replacing the sensor to repair a problem properly.
THROTTLE POSITION SENSOR
The Throttle Position (TP) sensor is a potentiometer connected to the throttle shaft of the throttle body. The TP sensor electrical circuit consists of a 5-volt supply line and a ground line, both provided by the Engine Control Module (ECM). The ECM calculates the throttle position by monitoring the voltage on this signal line. The TP sensor output changes as the accelerator pedal is moved, changing the throttle valve angle. At a closed throttle position, the output of the TP sensor is low, about 0.40.8 volt. As the throttle valve opens, the output increases so that, at Wide Open Throttle (WOT), the output voltage will be about 4.55 volts.
ELECTRIC EXHAUST GAS RECIRCULATION VALVE
The Electric Exhaust Gas Recirculation (EEGR) system is used on engines equipped with an automatic transaxle to lower oxides of nitrogen (NOx) emission levels caused by high combustion temperature. The main element of the system is the EEGR valve, controlled electrically by the Engine Control Module (ECM). The EEGR valve feeds small amounts of exhaust gas into the intake
DAEWOO M-150 BL2
ENGINE CONTROLS 1F 7
manifold to decrease combustion temperature. The amount of exhaust gas recirculated is controlled by variations in vacuum and exhaust back pressure. If too much exhaust gas enters, combustion will not take place. For this reason, very little exhaust gas is allowed to pass through the valve, especially at idle. The EEGR valve is usually open under the following conditions: D Warm engine operation. D Above idle speed. The IAC valve is mounted on the throttle body where it controls the engine idle speed under the command of the Engine Control Module (ECM). The ECM sends voltage pulses to the IAC valve motor windings, causing the IAC valve pintle to move in or out a given distance (a step or count) for each pulse. The pintle movement controls the airflow around the throttle valves which, in turn, control the engine idle speed. The desired idle speeds for all engine operating conditions are programmed into the calibration of the ECM. These programmed engine speeds are based on the coolant temperature, the park/neutral position switch status, the vehicle speed, the battery voltage, and the A/C system pressure, if equipped. The ECM "learns" the proper IAC valve positions to achieve warm, stabilized idle speeds (rpm) desired for the various conditions (park/neutral or drive, A/C on or off, if equipped). This information is stored in ECM "keep alive" memories (information is retained after the ignition is turned off). All other IAC valve positioning is calculated based on these memory values. As a result, engine variations due to wear and variations in the minimum throttle valve position (within limits) do not affect engine idle speeds. This system provides correct idle control under all conditions. This also means that disconnecting power to the ECM can result in incorrect idle control or the necessity to partially press the accelerator when starting until the ECM relearns idle control. Engine idle speed is a function of total airflow into the engine based on the IAC valve pintle position, the throttle valve opening, and the calibrated vacuum loss through accessories. The minimum throttle valve position is set at the factory with a stop screw. This setting allows enough airflow by the throttle valve to cause the IAC valve pintle to be positioned a calibrated number of steps (counts) from the seat during "controlled" idle operation. The minimum throttle valve position setting on this engine should not be considered the "minimum idle speed," as on other fuel injected engines. The throttle stop screw is covered with a plug at the factory following adjustment. If the IAC valve is suspected as being the cause of improper idle speed, refer to "Idle Air Control System Check" in this section.
Results of Incorrect Operation
Too much EEGR flow tends to weaken combustion, causing the engine to run roughly or to stop. With too much EEGR flow at idle, cruise, or cold operation, any of the following conditions may occur: D The engine stops after a cold start. D The engine stops at idle after deceleration. D The vehicle surges during cruise. D Rough idle. If the EEGR valve stays open all the time, the engine may not idle. Too little or no EEGR flow allows combustion temperatures to get too high during acceleration and load conditions. This could cause the following conditions: D Spark knock (detonation) D Engine overheating D Emission test failure
INTAKE AIR TEMPERATURE SENSOR
The Intake Air Temperature (IAT) sensor is a thermistor, a resistor which changes value based on the temperature of the air entering the engine. Low temperature produces a high resistance (100 kohms at 40_C [40_F]), while high temperature causes a low resistance (70 ohms at 130_C [266_F]). The Engine Control Module (ECM) provides 5 volts to the IAT sensor through a resistor in the ECM and measures the change in voltage to determine the IAT. The voltage will be high when the manifold air is cold and low when the air is hot. The ECM knows the intake IAT by measuring the voltage. The IAT sensor is also used to control spark timing when the manifold air is cold. A failure in the IAT sensor circuit sets a diagnostic trouble code P0112 or P0113.
MANIFOLD ABSOLUTE PRESSURE SENSOR
The Manifold Absolute Pressure (MAP) sensor measures the changes in the intake manifold pressure which result from engine load and speed changes and converts these to a voltage output. A closed throttle on engine coast down produces a relatively low MAP output. MAP is the opposite of vacuum. When manifold pressure is high, vacuum is low. The MAP sensor is also used to measure barometric pressure. This is performed as part of MAP sensor calcula-
IDLE AIR CONTROL VALVE
Notice: Do not attempt to remove the protective cap and readjust the stop screw. Misadjustment may result in damage to the Idle Air Control (IAC) valve or to the throttle body.
DAEWOO M-150 BL2
1F 8 ENGINE CONTROLS
tions. With the ignition ON and the engine not running, the Engine Control Module (ECM) will read the manifold pressure as barometric pressure and adjust the air/fuel ratio accordingly. This compensation for altitude allows the system to maintain driving performance while holding emissions low. The barometric function will update periodically during steady driving or under a wide open throttle condition. In the case of a fault in the barometric portion of the MAP sensor, the ECM will set to the default value. A failure in the MAP sensor circuit sets a diagnostic trouble codes P0107, P0108 or P0106. cause some fuel could be delivered to the engine after the ignition is turned off.
FUEL CUT-OFF SWITCH
The fuel cutoff switch is a safety device. In the event of a collision or a sudden impact, it automatically cuts off the fuel supply and activates the door lock relay. After the switch has been activated, it must be reset in order to restart the engine. Reset the fuel cutoff switch by pressing the rubber top of the switch. The switch is located near the right side of the passenger's seat.
ENGINE CONTROL MODULE
The Engine Control Module (ECM), is the control center of the fuel injection system. It constantly looks at the information from various sensors and controls the systems that affect the vehicle's performance. The ECM also performs the diagnostic functions of the system. It can recognize operational problems, alert the driver through the Malfunction Indicator Lamp (MIL), and store diagnostic trouble code(s) which identify the problem areas to aid the technician in making repairs. There are no serviceable parts in the ECM. The calibrations are stored in the ECM in the Programmable Read Only Memory (PROM). The ECM supplies either 5 or 12 volts to power the sensors or switches. This is done through resistance in the ECM which are so high in value that a test light will not come on when connected to the circuit. In some cases, even an ordinary shop voltmeter will not give an accurate reading because its resistance is too low. You must use a digital voltmeter with a 10 megohm input impedance to get accurate voltage readings. The ECM controls output circuits such as the fuel injectors, the Idle Air Control (IAC) valve, the A/C clutch relay, etc., by controlling the ground circuit through transistors or a device called a "quad-driver."
KNOCK SENSOR
The knock sensor detects abnormal knocking in the engine. The sensor is mounted in the engine block near the cylinders. The sensor produces an AC output voltage which increases with the severity of the knock. This signal is sent to the Engine Control Module (ECM). The ECM then adjusts the ignition timing to reduce the spark knock.
VARIABLE RELUCTANCE (VR) SENSOR
The variable reluctance sensor is commonly refered to as an "inductive" sensor. The VR wheel speed sensor consists of a sensing unit fixed to the left side front macpherson strut, for non-ABS vehicle. The ECM uses the rough road information to enable or disable the misfire diagnostic. The misfire diagnostic can be greatly affected by crankshaft speed variations caused by driving on rough road surfaces. The VR sensor generates rough road information by producing a signal which is proportional to the movement of a small metal bar inside the sensor. If a fault occurs which causes the ECM to not receive rough road information between 30 and 70 km/h (1.8 and 43.5 mph), Diagnostic Trouble Code (DTC) P1391 will set.
FUEL INJECTOR
The Multi-port Fuel Injection (MFI) assembly is a solenoid-operated device controlled by the Engine Control Module (ECM) that meters pressurized fuel to a single engine cylinder. The ECM energizes the fuel injector or solenoid to a normally closed ball or pintle valve. This allows fuel to flow into the top of the injector, past the ball or pintle valve, and through a recessed flow director plate at the injector outlet. The director plate has six machined holes that control the fuel flow, generating a conical spray pattern of finely atomized fuel at the injector tip. Fuel from the tip is directed at the intake valve, causing it to become further atomized and vaporized before entering the combustion chamber. A fuel injector which is stuck partially open would cause a loss of fuel pressure after the engine is shut down. Also, an extended crank time would be noticed on some engines. Dieseling could also occur be-
OCTANE NUMBER CONNECTOR
The octane number connector is a jumper harness that signal to the engine control module (ECM) the octane rating of the fuel. The connector is located on the next to the ECM. There are two different octane number connector settings available. The vehicle is shipped from the factory with a label attached to the jumper harness to indicate the octane rating setting of the ECM. The ECM will alter fuel delivery and spark timing based on the octane number setting. The following table shows which terminal to jump on the octane number connector in order to achieve the correct fuel octane rating. Terminal 2 is ground on the octane number connector. The find the
DAEWOO M-150 BL2
ENGINE CONTROLS 1F 9
appropriate wiring diagram. Refer to "ECM Wiring Diagrams" in this Section. 95 Terminal 49 Ground 91 Open
Verifying Vehicle Repair
Verification of the vehicle repair will be more comprehensive for vehicles with Euro On-Board Diagnostic (EOBD) system diagnostics. Following a repair, the technician should perform the following steps: Important: Follow the steps below when you verify repairs on EOBD systems. Failure to follow these steps could result in unnecessary repairs. D Review and record the Failure Records and the Freeze Frame data for the DTC which has been diagnosed (Freeze Fame data will only be stored for an A, B and E type diagnostic and only if the Malfunction Indicator Lamp has been requested). D Clear the DTC(s). D Operate the vehicle within conditions noted in the Failure Records and Freeze Frame data. D Monitor the DTC status information for the specific DTC which has been diagnosed until the diagnostic test associated with that DTC runs.
STRATEGY-BASED DIAGNOSTICS
Strategy-Based Diagnostics
The strategy-based diagnostic is a uniform approach to repair all Electrical/Electronic (E/E) systems. The diagnostic flow can always be used to resolve an E/E system problem and is a starting point when repairs are necessary. The following steps will instruct the technician on how to proceed with a diagnosis: Verify the customer complaint. To verify the customer complaint, the technician should know the normal operation of the system. D Perform preliminary checks as follows: D Conduct a thorough visual inspection. D Review the service history. D Detect unusual sounds or odors. D Gather Diagnostic Trouble Code (DTC) information to achieve an effective repair. D Check bulletins and other service information. This includes videos, newsletters, etc. D Refer to service information (manual) system check(s). D Refer to service diagnostics.
EOBD SERVICEABILITY ISSUES
Based on the knowledge gained from Euro On-Board Diagnostic (OBD) experience in the 1994 and 1995 model years in United Status, this list of non-vehicle faults that could affect the performance of the Euro OnBoard Diagnostic (EOBD) system has been compiled. These non-vehicle faults vary from environmental conditions to the quality of fuel used. With the introduction of EOBD across the entire passenger car, illumination of the Malfunction Indicator Lamp (MIL) due to a non-vehicle fault could lead to misdiagnosis of the vehicle, increased warranty expense and customer dissatisfaction. The following list of non-vehicle faults does not include every possible fault and may not apply equally to all product lines.
No Trouble Found
This condition exists when the vehicle is found to operate normally. The condition described by the customer may be normal. Verify the customer complaint against another vehicle that is operating normally. The condition may be intermittent. Verify the complaint under the conditions described by the customer before releasing the vehicle. Re-examine the complaints. When the complaints cannot be successfully found or isolated, a re-evaluation is necessary. The complaint should be re-verified and could be intermittent as defined in "intermittents," or could be normal. After isolating the cause, the repairs should be made. Validate for proper operation and verify that the symptom has been corrected. This may involve road testing or other methods to verify that the complaint has resolved under following conditions: D Conditions noted by the customer. D If a DTC was diagnosed, verify the repair be duplicating conditions present when the DTC was set as noted in Failure Records or Freeze Frame data.
Fuel Quality
Fuel quality is not a new issue for the automotive industry, but its potential for turning on the MIL with EOBD systems is new. Fuel additives such as "dry gas" and "octane enhancers" may affect the performance of the fuel. If this results in an incomplete combustion or a partial burn, it will set Diagnostic Trouble Code (DTC) P0300. The Reed Vapor Pressure of the fuel can also create problems in the fuel system, especially during the spring and fall months when severe ambient temperature swings occur. A high Reed Vapor Pressure could show up as a Fuel Trim DTC due to excessive canister loading. Using fuel with the wrong octane rating for your vehicle may cause driveability problems. Many of the major fuel companies advertise that using "premium" gasoline will improve the performance of your vehicle. Most premium
DAEWOO M-150 BL2
1F 10 ENGINE CONTROLS
fuels use alcohol to increase the octane rating of the fuel. Although alcohol-enhanced fuels may raise the octane rating, the fuel's ability to turn into vapor in cold temperatures deteriorates. This may affect the starting ability and cold driveability of the engine. Low fuel levels can lead to fuel starvation, lean engine operation, and eventually engine misfire. if the ECM detected a Misfire fault, the diagnostics on the catalytic converter would be suspended until the Misfire fault was repaired. If the Misfire fault is severe enough, the catalytic converter can be damaged due to overheating and will never set a Catalyst DTC until the Misfire fault is repaired and the Catalyst diagnostic is allowed to run to completion. If this happens, the customer may have to make two trips to the dealership in order to repair the vehicle.
Non-OEM Parts
The EOBD system has been calibrated to run with Original Equipment Manufacturer (OEM) parts. Something as simple as a high performance-exhaust system that affects exhaust system back pressure could potentially interfere with the operation of the Electric Exhaust Gas Recirculation (EEGR) valve and thereby turn on the MIL. Small leaks in the exhaust system near the heated oxygen sensor (HO2S) can also cause the MIL to turn on. Aftermarket electronics, such as cellular phones, stereos, and anti-theft devices, may radiate Electromagnetic Interference (EMI) into the control system if they are improperly installed. This may cause a false sensor reading and turn on the MIL.
SERIAL DATA COMMUNICATIONS
Keyword 2000 Serial Data Communications
Government regulations require that all vehicle manufacturers establish a common communication system. This vehicle utilizes the "Keyword 2000" communication system. Each bit of information can have one of two lengths: long or short. This allows vehicle wiring to be reduced by transmitting and receiving multiple signals over a single wire. The messages carried on Keyword 2000 data streams are also prioritized. If two messages attempt to establish communications on the data line at the same time, only the message with higher priority will continue. The device with the lower priority message must wait. The most significant result of this regulation is that it provides scan tool manufacturers with the capability to access data from any make or model vehicle that is sold. The data displayed on the other scan tool will appear the same, with some exceptions. Some scan tools will only be able to display certain vehicle parameters as values that are a coded representation of the true or actual value. On this vehicle, the scan tool displays the actual values for vehicle parameters. It will not be necessary to perform any conversions from coded values to actual values.
Environment
Temporary environmental conditions, such as localized flooding, will have an effect on the vehicle ignition system. If the ignition system is rain-soaked, it can temporarily cause engine misfire and turn on the MIL.
Vehicle Marshaling
The transportation of new vehicles from the assembly plant to the dealership can involve as many as 60 key cycles within 2 to 3 miles of driving. This type of operation contributes to the fuel fouling of the spark plugs and will turn on the MIL with a set DTC P0300.
Poor Vehicle Maintenance
The sensitivity of the EOBD will cause the MIL to turn on if the vehicle is not maintained properly. Restricted air filters, fuel filters, and crankcase deposits due to lack of oil changes or improper oil viscosity can trigger actual vehicle faults that were not previously monitored prior to EOBD. Poor vehicle maintenance can not be classified as a "non-vehicle fault," but with the sensitivity of the EOBD, vehicle maintenance schedules must be more closely followed.
EURO ON-BOARD DIAGNOSTIC (EOBD)
Euro On-Board Diagnostic Tests
A diagnostic test is a series of steps, the result of which is a pass or fail reported to the diagnostic executive. When a diagnostic test reports a pass result, the diagnostic executive records the following data: D The diagnostic test has been completed since the last ignition cycle. D The diagnostic test has passed during the current ignition cycle. D The fault identified by the diagnostic test is not currently active. When a diagnostic test reports a fail result, the diagnostic executive records the following data: D The diagnostic test has been completed since the last ignition cycle.
Severe Vibration
The Misfire diagnostic measures small changes in the rotational speed of the crankshaft. Severe driveline vibrations in the vehicle, such as caused by an excessive amount of mud on the wheels, can have the same effect on crankshaft speed as misfire and, therefore, may set DTC P0300.
Related System Faults
Many of the EOBD system diagnostics will not run if the Engine Control Module (ECM) detects a fault on a related system or component. One example would be that
DAEWOO M-150 BL2
ENGINE CONTROLS 1F 11
D The fault identified by the diagnostic test is currently active. D The fault has been active during this ignition cycle. D The operating conditions at the time of the failure. Remember, a fuel trim Diagnostic Trouble Code (DTC) may be triggered by a list of vehicle faults. Make use of all information available (other DTCs stored, rich or lean condition, etc.) when diagnosing a fuel trim fault. test, actually takes some sort of action when performing diagnostic functions, often in response to a failed passive test. For example, the Electric Exhaust Gas Recirculation (EEGR) diagnostic active test will force the EEGR valve open during closed throttle deceleration and/or force the EEGR valve closed during a steady state. Either action should result in a change in manifold pressure.
Intrusive Diagnostic Tests
This is any Euro On-Board test run by the Diagnostic Management System which may have an effect on vehicle performance or emission levels.
COMPREHENSIVE COMPONENT MONITOR DIAGNOSTIC OPERATION
Comprehensive component monitoring diagnostics are required to monitor emissions-related input and output powertrain components.
Warm-Up Cycle
A warm-up cycle means that engine at temperature must reach a minimum of 70_C (160_F) and rise at least 22_C (40_F) over the course of a trip.
Input Components
Input components are monitored for circuit continuity and out-of-range values. This includes rationality checking. Rationality checking refers to indicating a fault when the signal from a sensor does not seem reasonable, i.e. Throttle Position (TP) sensor that indicates high throttle position at low engine loads or Manifold Absolute Pressure (MAP) voltage. Input components may include, but are not limited to, the following sensors: D Vehicle Speed Sensor (VSS). D Crankshaft Position (CKP) sensor. D D D D Throttle Position (TP) sensor. Engine Coolant Temperature (ECT) sensor. Camshaft Position (CMP) sensor. MAP sensor.
Freeze Frame
Freeze Frame is an element of the Diagnostic Management System which stores various vehicle information at the moment an emissions-related fault is stored in memory and when the MIL is commanded on. These data can help to identify the cause of a fault.
Failure Records
Failure Records data is an enhancement of the EOBD Freeze Frame feature. Failure Records store the same vehicle information as does Freeze Frame, but it will store that information for any fault which is stored in Euro On-Board memory, while Freeze Frame stores information only for emission-related faults that command the MIL on.
In addition to the circuit continuity and rationality check, the ECT sensor is monitored for its ability to achieve a steady state temperature to enable closed loop fuel control.
COMMON EOBD TERMS
Diagnostic
When used as a noun, the word diagnostic refers to any Euro On-Board test run by the vehicle's Diagnostic Management System. A diagnostic is simply a test run on a system or component to determine if the system or component is operating according to specification. There are many diagnostics, shown in the following list: D Misfire. D Oxygen sensors (O2S) D Heated oxygen sensor (HO2S) D Electric Exhaust Gas Recirculation (EEGR) D Catalyst monitoring
Output Components
Output components are diagnosed for proper response to control module commands. Components where functional monitoring is not feasible will be monitored for circuit continuity and out-of-range values if applicable. Output components to be monitored include, but are not limited to the following circuit: D D D D Idle Air Control (IAC) Motor. Controlled Canister Purge Valve. A/C relays. Cooling fan relay.
D VSS output. D Malfunction Indicator Lamp (MIL) control. Refer to "Engine Control Module" and the sections on Sensors in General Descriptions.
Enable Criteria
The term "enable criteria" is engineering language for the conditions necessary for a given diagnostic test to run. Each diagnostic has a specific list of conditions which must be met before the diagnostic will run. "Enable criteria" is another way of saying "conditions required."
Passive and Active Diagnostic Tests
A passive test is a diagnostic test which simply monitors a vehicle system or component. Conversely, an active
DAEWOO M-150 BL2
1F 12 ENGINE CONTROLS
The enable criteria for each diagnostic is listed on the first page of the Diagnostic Trouble Code (DTC) description under the heading "Conditions for Setting the DTC." Enable criteria varies with each diagnostic and typically includes, but is not limited to the following items: D Engine speed. D Vehicle speed D D D D Engine Coolant Temperature (ECT) Manifold Absolute Pressure (MAP) Barometric Pressure (BARO) Intake Air Temperature (IAT)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) is required by Euro On-Board Diagnostics (EOBD) to illuminate under a strict set of guidelines. Basically, the MIL is turned on when the Engine Control Module (ECM) detects a DTC that will impact the vehicle emissions. The MIL is under the control of the Diagnostic Executive. The MIL will be turned on if an emissions-related diagnostic test indicates a malfunction has occurred. It will stay on until the system or component passes the same test for three consecutive trips with no emissions related faults.
D Throttle Position (TP) D High canister purge D Fuel trim D A/C on
Extinguishing the MIL
When the MIL is on, the Diagnostic Executive will turn off the MIL after three consecutive trips that a "test passed" has been reported for the diagnostic test that originally caused the MIL to illuminate. Although the MIL has been turned off, the DTC will remain in the ECM memory (both Freeze Frame and Failure Records) until forty (40) warm-up cycles after no faults have been completed. If the MIL was set by either a fuel trim or misfire-related DTC, additional requirements must be met. In addition to the requirements stated in the previous paragraph, these requirements are as follows: D The diagnostic tests that are passed must occur with 375 rpm of the rpm data stored at the time the last test failed. D Plus or minus ten percent of the engine load that was stored at the time the last test failed. Similar engine temperature conditions (warmed up or warming up) as those stored at the time the last test failed. Meeting these requirements ensures that the fault which turned on the MIL has been corrected. The MIL is on the instrument panel and has the following functions: D It informs the driver that a fault affecting the vehicle's emission levels has occurred and that the vehicle should be taken for service as soon as possible. D As a system check, the MIL will come on with the key ON and the engine not running. When the engine is started, the MIL will turn OFF. D When the MIL remains ON while the engine is running, or when a malfunction is suspected due to a driveability or emissions problem, an EOBD System Check must be performed. The procedures for these checks are given in EOBD System Check. These checks will expose faults which may not be detected if other diagnostics are performed first.
Trip
Technically, a trip is a key-on run key-off cycle in which all the enable criteria for a given diagnostic are met, allowing the diagnostic to run. Unfortunately, this concept is not quite that simple. A trip is official when all the enable criteria for a given diagnostic are met. But because the enable criteria vary from one diagnostic to another, the definition of trip varies as well. Some diagnostics are run when the vehicle is at operating temperature, some when the vehicle first starts up; some require that the vehicle cruise at a steady highway speed, some run only when the vehicle is at idle. Some run only immediately following a cold engine start-up. A trip then, is defined as a key-on run-key off cycle in which the vehicle is operated in such a way as to satisfy the enable criteria for a given diagnostic, and this diagnostic will consider this cycle to be one trip. However, another diagnostic with a different set of enable criteria (which were not met) during this driving event, would not consider it a trip. No trip will occur for that particular diagnostic until the vehicle is driven in such a way as to meet all the enable criteria.
Diagnostic Information
The diagnostic charts and functional checks are designed to locate a faulty circuit or component through a process of logical decisions. The charts are prepared with the requirement that the vehicle functioned correctly at the time of assembly and that there are not multiple faults present. There is a continuous self-diagnosis on certain control functions. This diagnostic capability is complimented by the diagnostic procedures contained in this manual. The language of communicating the source of the malfunction is a system of diagnostic trouble codes. When a malfunction is detected by the control module, a DTC is set, and the Malfunction Indicator Lamp (MIL) is illuminated.
DAEWOO M-150 BL2
ENGINE CONTROLS 1F 13 Data Link Connector (DLC)
The provision for communicating with the control module is the Data Link Connector (DLC). The DLC is used to connect to a scan tool. Some common uses of the scan tool are listed below: D Identifying stored DTCs. D Clearing DTCs. D Performing output control tests. D Reading serial data. D Requests illumination of the MIL on the third consecutive trip with a fail. D Stores a History DTC on the third consecutive trip with a fail (The DTC will be armed after the second fail). D Stores a Freeze Frame on the third consecutive trip with a fail (if empty). Important: For 0.8 SOHC engine eight fail records can be stored. Each Fail Record is for a different DTC. It is possible that there will not be Fail Records for every DTC if multiple DTCs are set.
DTC TYPES
Each Diagnostic Trouble Code (DTC) is directly related to a diagnostic test. The Diagnostic Management System sets DTCs based on the failure of the tests during a trip or trips. Certain tests must fail two consecutive trips before the DTC is set. The following are the three types of DTCs and the characteristics of those codes:
Special Cases of Type B Diagnostic Tests
Unique to the misfire diagnostic, the Diagnostic Executive has the capability of alerting the vehicle operator to potentially damaging levels of misfire. If a misfire condition exists that could potentially damage the catalytic converter as a result of high misfire levels, the Diagnostic Executive will command the MIL to "flash" as a rate of once per seconds during those the time that the catalyst damaging misfire condition is present. Fuel trim and misfire are special cases of Type B diagnostics. Each time a fuel trim or misfire malfunction is detected, engine load, engine speed, and Engine Coolant Temperature (ECT) are recorded. When the ignition is turned OFF, the last reported set of conditions remain stored. During subsequent ignition cycles, the stored conditions are used as a reference for similar conditions. If a malfunction occurs during two consecutive trips, the Diagnostic Executive treats the failure as a normal Type B diagnostic, and does not use the stored conditions. However, if a malfunction occurs on two non-consecutive trips, the stored conditions are compared with the current conditions. The MIL will then illuminate under the following conditions: D When the engine load conditions are within 10% of the previous test that failed. D Engine speed is within 375 rpm, of the previous test that failed. D ECT is in the same range as the previous test that failed.
Type A
D Emissions related. D Requests illumination of the Malfunction Indicator. Lamp (MIL) of the first trip with a fail. D D D D Stores a History DTC on the first trip with a fail. Stores a Freeze Frame (if empty). Stores a Fail Record. Updates the Fail Record each time the diagnostic test fails.
Type B
D Emissions related. D "Armed" after one trip with a fail. D "Disarmed" after one trip with a pass. D Requests illumination of the MIL on the second consecutive trip with a fail. D Stores a History DTC on the second consecutive trip with a fail (The DTC will be armed after the first fail). D Stores a Freeze Frame on the second consecutive trip with a fail (if empty).
Type Cnl
D Non-Emissions related. D Does not request illumination of any lamp. D Stores a History DTC on the first trip with a fail . D Does not store a Freeze Frame. D Stores Fail Record when test fails. D Updates the Fail Record each time the diagnostic test fails.
READING DIAGNOSTIC TROUBLE CODES
The procedure for reading Diagnostic Trouble Code(s) (DTC) is to use a diagnostic scan tool. When reading DTC(s), follow instructions supplied by tool manufacturer.
Clearing Diagnostic Trouble Codes
Important: Do not clear DTCs unless directed to do so by the service information provided for each diagnostic procedure. When DTCs are cleared, the Freeze Frame and Failure Record data which may help diagnose an in-
Type E
D Emissions related. D "Armed" after two consecutive trip with a fail. D "Disarmed" after one trip with a pass.
DAEWOO M-150 BL2
1F 14 ENGINE CONTROLS
termittent fault will also be erased from memory. If the fault that caused the DTC to be stored into memory has been corrected, the Diagnostic Executive will begin to count the ``warm-up" cycles with no further faults detected, the DTC will automatically be cleared from the Engine Control Module (ECM) memory. To clear DTCs, use the diagnostic scan tool. It can't cleared DTCs without the diagnostic scan tool. So you must use the diagnostic scan tool. Notice: To prevent system damage, the ignition key must be OFF when disconnecting or reconnecting battery power. D The power source to the control module. Examples: fuse, pigtail at battery ECM connectors, etc. D The negative battery cable. (Disconnecting the negative battery cable will result in the loss of other Euro On-Board memory data, such as preset radio tuning.)
Fail This Ign. (Fail This Ignition)
This selection will display all DTCs that have failed during the present ignition cycle.
History
This selection will display only DTCs that are stored in the ECM's history memory. It will not display Type B DTCs that have not requested the Malfunction Indicator Lamp (MIL). It will display all type A, B and E DTCs that have requested the MIL and have failed within the last 40 warm-up cycles. In addition, it will display all type C and type D DTCs that have failed within the last 40 warm-up cycles.
Last Test Fail
This selection will display only DTCs that have failed the last time the test ran. The last test may have run during a previous ignition cycle if a type A or type B DTC is displayed. For type C and type D DTCs, the last failure must have occurred during the current ignition cycle to appear as Last Test Fail.
DTC Modes
On Euro On-Board Diagnostic (EOBD) passenger cars there are five options available in the scan tool DTC mode to display the enhanced information available. A description of the new modes, DTC Info and Specific DTC, follows. After selecting DTC, the following menu appears: D D D D DTC Info. Specific DTC. Freeze Frame. Fail Records (not all applications).
MIL Request
This selection will display only DTCs that are requesting the MIL. Type C and type D DTCs cannot be displayed using this option. This selection will report type B and E DTCs only after the MIL has been requested.
Not Run SCC (Not Run Since Code Clear)
This option will display up to 33 DTCs that have not run since the DTCs were last cleared. Since the displayed DTCs have not run, their condition (passing or failing) is unknown.
D Clear Info. The following is a brief description of each of the sub menus in DTC Info and Specific DTC. The order in which they appear here is alphabetical and not necessarily the way they will appear on the scan tool.
Test Fail SCC (Test Failed Since Code Clear)
This selection will display all active and history DTCs that have reported a test failure since the last time DTCs were cleared. DTCs that last failed more than 40 warmup cycles before this option is selected will not be displayed.
DTC Information Mode
Use the DTC info mode to search for a specific type of stored DTC information. There are seven choices. The service manual may instruct the technician to test for DTCs in a certain manner. Always follow published service procedures. To get a complete description of any status, press the ``Enter" key before pressing the desired F-key. For example, pressing ``Enter" then an F-key will display a definition of the abbreviated scan tool status.
Specific DTC Mode
This mode is used to check the status of individual diagnostic tests by DTC number. This selection can be accessed if a DTC has passed, failed or both. Many EOBD DTC mode descriptions are possible because of the extensive amount of information that the diagnostic executive monitors regarding each test. Some of the many possible descriptions follow with a brief explanation. The "F2" key is used, in this mode, to display a description of the DTC. The "Yes" and "No" keys may also be used to display more DTC status information. This selection will only allow entry of DTC numbers that are supported by the vehicle being tested. If an attempt is,
DTC Status
This selection will display any DTCs that have not run during the current ignition cycle or have reported a test failure during this ignition up to a maximum of 33 DTCs. DTC tests which run and pass will cause that DTC number to be removed from the scan tool screen.
DAEWOO M-150 BL2
ENGINE CONTROLS 1F 15
made to enter DTC numbers for tests which the diagnostic e