M34a Hydraulic Brakes.pdf part of Daewoo Matiz 796cc (My 2003).part01.rar, Service Manual, Wiring Diagram - 16 Part File

Text preview for : M34a Hydraulic Brakes.pdf part of Daewoo Matiz Service Manual, Wiring Diagram - 16 Part File - 62 File

Back to : 796cc (My 2003).part01.ra | Home

SECTION 4A

HYDRAULIC BRAKES
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise noted.

TABLE OF CONTENTS
Description and Operation . . . . . . . . . . . . . . . . . . Warning Lamp Operation . . . . . . . . . . . . . . . . . . . Component Locator . . . . . . . . . . . . . . . . . . . . . . . . Brake System (Non-ABS) . . . . . . . . . . . . . . . . . . Diagnostic Information and Procedures . . . . . Brake System Testing . . . . . . . . . . . . . . . . . . . . . . Brake Hose Inspection . . . . . . . . . . . . . . . . . . . . . Warning Lamp Operation . . . . . . . . . . . . . . . . . . . 4A-2 4A-2 4A-3 4A-3 4A-4 4A-4 4A-4 4A-5 Repair Instructions . . . . . . . . . . . . . . . . . . . . . . . . . On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . . . . . Brake Hose (Front) . . . . . . . . . . . . . . . . . . . . . . . . Brake Hose (Rear) . . . . . . . . . . . . . . . . . . . . . . . . 4A-8 4A-8 4A-8 4A-9

Stoplamp Switch . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-9 Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-10 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-13 General Specifications . . . . . . . . . . . . . . . . . . . . 4A-13 Fastener Tightening Specifications . . . . . . . . . . 4A-13 Schematic and Routing Diagrams . . . . . . . . . . 4A-14 Brake Lamp Warning Circuit . . . . . . . . . . . . . . . 4A-14 Stoplamp Switch Circuit . . . . . . . . . . . . . . . . . . . 4A-14

Brake System Fault . . . . . . . . . . . . . . . . . . . . . . . . 4A-5 Manual Bleeding the Brakes . . . . . . . . . . . . . . . . 4A-6 Pedal Travel Check . . . . . . . . . . . . . . . . . . . . . . . . 4A-6 Brake Pedal Free Play Inspection . . . . . . . . . . . 4A-7

DAEWOO M-150 BL2

4A 2 HYDRAULIC BRAKES

DESCRIPTION AND OPERATION
WARNING LAMP OPERATION
This brake system uses a BRAKE warning lamp located in the instrument panel cluster. When the ignition switch is in the III position, the BRAKE warning lamp should illuminate. It should go off when the ignition switch return to II position. The following conditions will activate the BRAKE warning lamp. D The lamp should be on whenever the parking brake applied and the ignition switch is in the II position. D A low fluid level in the master cylinder will turn the BRAKE warning lamp on.

D17A007A

DAEWOO M-150 BL2

HYDRAULIC BRAKES 4A 3

COMPONENT LOCATOR
BRAKE SYSTEM (NONABS)
(LeftHand Drive Shown, RightHand Drive Similar)

MAB4A001

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.

Power Booster Power Booster Boot Cotter Pin Clevis Clevis Pin Packing Spacer Master Cylinder Assembly Fluid Reservoir Assembly Reservoir Cap Reservoir Grommet Seal Master Cylinder Proportioning Valve Stoplamp Switch Brake Pedal Assembly Clutch Pedal Spring

18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34.

Pedal Bracket Assembly Clutch Pedal Pad Clutch Pedal Cushion Bushing Retaining Ring Spring Brake Pedal Pad Brake Pedal Brake Pedal Spring Accelator Pedal Pad Accelator Pedal Rear Drum Brake Hose E Ring Front Disc Brake Hose Brake Hose Coupling Bolt Plain Washer

DAEWOO M-150 BL2

4A 4 HYDRAULIC BRAKES

DIAGNOSITIC INFORMATION AND PROCEDURES
BRAKE SYSTEM TESTING
(LeftHand Drive Shown, RightHand Drive Similar)
Brakes should be tested on a dry, clean, reasonably smooth and level roadway. A true test of brake performance cannot be made if the roadway is wet, greasy, or covered with loose dirt whereby all tires do not grip the road equally. Testing will also be adversely affected if the roadway is crowned so as to throw the weight so roughly that the wheels tend to bounce. Test the brakes at different vehicle speeds with both light and heavy pedal pressure; however, avoid locking the brakes and sliding the tires. Locked brakes and sliding tires do not indicate brake efficiency since heavily braked, but turning, wheels will stop the vehicle in less distance than locked brakes. More tire-to-road friction is present with a heavily braked, turning tire than with a sliding tire. Because of the high deceleration capability, a firmer pedal may be felt at higher deceleration levels. There are three major external conditions that affect brake performance: D Tires having unequal contact and grip of the road will cause unequal braking. Tires must be equally inflated, and the tread pattern of the right and the left tires must be approximately equal. D Unequal loading of the vehicle can affect the brake performance since the most heavily loaded wheels require more braking power, and thus more braking effort, than the others. D Misalignment of the wheels, particularly conditions of excessive camber and caster, will cause the brakes to pull to one side. To check for brake fluid leaks, hold constant foot pressure on the pedal with the engine running at idle and the shift lever in NEUTRAL. If the pedal gradually falls away with the constant pressure, the hydraulic system may be leaking. Perform a visual check to confirm any suspected leaks. Check the master cylinder fluid level. While a slight drop in the reservoir level results from normal lining wear, an abnormally low level indicates a leak in the system. The hydraulic system may be leaking either internally or externally. Refer to the procedure below to check the master cylinder. Also, the system may appear to pass this test while still having a slight leak. If the fluid level is normal, check the vacuum booster pushrod length. If an incorrect pushrod length is found, adjust or replace the rod. Check the master cylinder using the following procedure: D Check for a cracked master cylinder casting or brake fluid leaking around the master cylinder. Leaks are indicated only if there is at least one drop of fluid. A damp condition is not abnormal. D Check for a binding pedal linkage and for an incorrect pushrod length. If both of these parts are in satisfactory condition, disassemble the master cylinder and check for an elongated or swollen primary cylinder or piston seals. If swollen seals are found, substandard or contaminated brake fluid should be suspected. If contaminated brake fluid is found, all the components should be disassembled and cleaned, and all the rubber components should be replaced. All of the pipes must also be flushed. Improper brake fluid, or mineral oil or water in the fluid, may cause the brake fluid to boil or cause deterioration of the rubber components. If the primary piston cups in the master cylinder are swollen, then the rubber parts have deteriorated. This deterioration may also be evidenced by swollen wheel cylinder piston seals on the drum brake wheels. If rubber deterioration is evident, disassemble all the hydraulic parts and wash the parts with alcohol. Dry these parts with compressed air before reassembly to keep alcohol out of the system. Replace all the rubber parts in the system, including the hoses. Also, when working on the brake mechanisms, check for fluid on the linings. If excessive fluid is found, replace the linings. If the master cylinder piston seals are in satisfactory condition, check for leaks or excessive heat conditions. If these conditions are not found, drain the fluid, flush the master cylinder with brake fluid, refill the master cylinder, and bleed the system. Refer to "Manual Bleeding the Brakes" in this section.

BRAKE HOSE INSPECTION
The hydraulic brake hoses should be inspected at least twice a year. The brake hose assembly should be checked for road hazard damage, cracks, chafing of the outer cover, and for leaks or blisters. Inspect the hoses for proper routing and mounting. A brake hose that rubs on a suspension component will wear and eventually fail. A light and a mirror may be needed for an adequate inspection. If any of the above conditions are observed on the brake hose, adjust or replace the hose as necessary.

DAEWOO M-150 BL2

HYDRAULIC BRAKES 4A 5

WARNING LAMP OPERATION
This brake system uses a BRAKE warning lamp located in the instrument panel cluster. When the ignition switch is in the III position, the BRAKE warning lamp should glow and then go OFF when the ignition switch returns to the II position.

The following conditions will activate the BRAKE lamp: D Parking brake applied. The light should be on whenever the parking brake is applied and the ignition switch is II. D Low fluid level. A low fluid level in the master cylinder will turn the BRAKE lamp ON.

BRAKE SYSTEM FAULT

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á
Condition Probable cause Correction Brake Warning Lamp ON D Brake fluid leaks. D Repair the leaks or add th fluid. D Repair the short ground. D Replace the sensor. D Replace the stoplamp switch. D Adjust the push rod length of the power booster. D Repair or Replace the wiring harness. D Repair the leaks or add the fluid. D Replace the fluid. D Bleed the brake system. D Replace the brake lines. D Replace the vacuum hose or check value. D Adjust the free play. D Replace the return spring. D Replace the master cylinder. D Bleed the brake system. D Repair the leaks or add the fluid. D Adjust the push rod length of the power booster. D Parking brake switch shorted to ground. D Faulty the fluid level sensor. Stoplamp ON D Faulty the stoplamp switch. D Push rod length is short. D Stoplamp switch circuit shorted to battery. Poor Braking D Brake fluid lacks or leaks. D Brake fluid contamination. D Air in the brake system. D Damaged brake lines. D Damaged vacuum hose or faulty check valve. Dragging Brake D No free play at the brake pedal. D Weakened the brake pedal return spring. D Faulty master cylinder. D Air in the brake system. Pedal Over Stroke D Brake fluid lacks or leaks. D Poor adjustment of the brake pedal free play.
DAEWOO M-150 BL2

4A 6 HYDRAULIC BRAKES

MANUAL BLEEDING THE BRAKES
Important: The bleeding sequence is as follows; right rear, left rear, right front, and left front. Important: Check the fluid level and add the fluid during the bleeding operation. 1. Raise the vehicle. 2. Remove the bleeder screw and cap.

5. Tighten the bleeder screw after loosening the bleeder screw and draining the fluid. Caution: Hold the brake pedal until tightening the bleeder screw. 6. Repeat the step 5, 6 until all the air is removed. 7. Check the leaks for the bleeder screw.

PEDAL TRAVEL CHECK
1. Start the engine. 2. Push the pedal three times. 3. With brake pedal depressed with a about 30Kg (66.15 lb) load, measure the clearance between the pedal pad and the lower dash panel. Unit : mm (in.) Specification 60 (2.36)

D17B703B

3. Attach a transparent tube over the valve. Allow the tube to hang submerged in brake fluid in a transparent container.

D107A303

4. Slowly push the brake pedal several times and hold the brake pedal.

ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ
D107A304

4. If clearance is less than 60mm (2.36 in.), the most possible cause is either rear drum brake shoes are worn out beyond the specification value or air is in lines. Clearance still remains less than 60mm (2.36 in.) even after replacement of brake shoes and bleeding of the brake system, other possible but infrequent cause is malfunction of rear drum brake shoe adjusters or booster push rod length out of adjustment. 5. Automatic clearance adjuster check is performed after removing brake drums. If the faulty is found, repair or replace it.

DAEWOO M-150 BL2

HYDRAULIC BRAKES 4A 7

BRAKE PEDAL FREE PLAY INSPECTION
1. Push the brake pedal several times to discharge the vacuum of the power booster. 2. Measure the pedal movement until the hardness is felt when pushing the brake pedal by hand.

3. Brake pedal free play can not be adjusted.

Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁ
Specification 610 (0.240.31)
D107A305
DAEWOO M-150 BL2

Unit : mm (in.)

4A 8 HYDRAULIC BRAKES

REPAIR INSTRUCTIONS ONVEHICLE SERVICE
BRAKE HOSE (FRONT)
Removal Procedure
1. Remove the wheels. Refer to Section 2E, Tires and Wheels. 2. Remove the brake hose. D Remove the fitting (1). D Remove the Ering retainer (2). D Disconnect the brake hose mounting from the strut (3). D Remove the coupling bolt (4). D Plug the opening in the brake pipe and caliper to prevent fluid loss or contamination.

D107A528

Installation Procedure
1. Connect the brake lines to the brake hose (1).

Tighten
Tighten the brake pipetohose fitting to 16 NSm (12 lb-ft). 2. Install the brake hose coupling bolt (2).

Tighten
Tighten the bolt to 25.5 NSm (19.1 lb-ft). Important: Use only Daewoo recommended brake fluid.
D17A529B

3. Bleed the brake system. Refer to "Manual Bleeding the Brakes" in this section. 4. Check the brake system for leaks. 5. Install the wheels. Refer to Section 2E, Tires and Wheels.

DAEWOO M-150 BL2

HYDRAULIC BRAKES 4A 9

BRAKE HOSE (REAR)
Removal Procedure
1. Remove the wheels. Refer to Section 2E, Tires and Wheels. 2. Remove the brake hose. D Remove the fittings (1). D Remove the Erings (2). D Plug the opening in the brake pipe to prevent fluid loss or contamination.

D107A530

Installation Procedure
1. Connect the brake lines to the brake hose. 2. Install the fitting and Erings.

Tighten
Tighten the fitting to 16 NSm (12 lb-ft). Important: Use only Daewoo recommended brake fluid. 3. Bleed the brake system. Refer to "Manual Bleeding the Brakes" in this section. 4. Check the brake system for leaks. 5. Install the wheels. Refer to Section 2E, Tires and Wheels.

D17A531A

STOPLAMP SWITCH
(LeftHand Drive Shown, RightHand Drive Similar) Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the stoplamp switch. D Disconnect the connector (1). D Turn the stoplamp switch (2).

D107A523

Installation Procedure
1. Install the stoplamp switch. 2. Connect the electrical connector. 3. Connect the negative battery cable. Important: After installing the stoplamp switch, pull the lever completely.

D107A524

DAEWOO M-150 BL2

4A 10 HYDRAULIC BRAKES

BRAKE PEDAL (LEFTHAND DRIVE)
Removal Procedure
1. Remove the stoplamp switch. Refer to "Stoplamp Switch" in this section. 2. Disconnect the brake pedal from the power booster. Refer to Section 4C, Power Booster. 3. Remove the brake pedal. D Remove the bolt (1).

D107A525

D D D D

Remove the brake pedal spring (2). Remove the bushing (3). Remove the cushion (4). Remove the brake pedal pad (5).

D107A526

Installation Procedure
1. Install the pad to the brake pedal. 2. Install the brake pedal with spring, bushing, and cushion. 3. Connect the brake pedal to the power booster.

Tighten
Tighten the brake pedaltopedal bracket bolt to 18 NSm (13 lb-ft). 4. Install the stoplamp switch. Refer to "Stoplamp Switch" in this section.
D17A527A

BRAKE PEDAL (RIGHTHAND DRIVE)
Removal Procedure
1. Remove the instrument panel assembly. Refer to Section 9E, Instrument/Driver Information. 2. Disconnect the brake pedal rod from the power booster. Refer to Section 4C, Power Booster.

D24C001A

DAEWOO M-150 BL2

HYDRAULIC BRAKES 4A 11
3. Remove the stoplamp switch. D Remove the stoplamp switch (1). D Remove the bolts (2). D Remove the stoplamp switch bracket (3).

D24D001

4. Remove the bolts mounting brake pedal bracket (1). 5. Remove the nuts mounting brake pedal bracket (2).

D24D002

6. Remove the canister. Refer to Section 1F, Engine Controls. 7. Remove the bolt mounting brake pedal bracket in the engine compartment (1).

D24D003

8. Remove the brake pedal. D Remove the snap rings (1). D Remove the bushings (2). D Remove the brake pedal spring (3). D Remove the cushion (4). D Remove the brake pedal pad (5).

D24D004

DAEWOO M-150 BL2

4A 12 HYDRAULIC BRAKES Installation Procedure
1. Install the brake pedal with pad, spring, bushings, and cushion. 2. Install the bolt mounting brake pedal bracket in the engine compartment.

Tighten
Tighten the bolt to 1826 NSm (1320 lb-ft). 3. Install the canister. Refer to Section 1F, Engine Controls.

D24D005

4. Install the brake pedal with the snap rings. 5. Install the bolts and nuts mounting brake pedal bracket.

Tighten
D Tighten the bolts mounting brake pedal bracket to 1826 NSm (1320 lb-ft). D Tighten the nuts mounting brake pedal bracket to 1826 NSm (1320 lb-ft).

D24D006

6. Install the stoplamp switch with the bracket and the bolts.

Tighten
Tighten the mounting bolts to 912 NSm (80106 lbin.) 7. Connect the brake pedal rod to the power booster. Refer to Section 4C, Power Booster. 8. Install the instrument panel assembly. Refer to Section 9E, Instrument/Driver Information.

D24D007

DAEWOO M-150 BL2

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á Á Á Á Á Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁ Á Á Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Stoplamp Switch Mounting Bracket Bolts Brake Pedal Bracket Mounting Nuts Brake Pedal Bracket Mounting Bolts Brake PedaltoPedal Bracket Hex Bolt Front Brake Hose-to-Caliper Bolt Brake Pipe Fittings Brake Fluid Brake Pedal: Free Play Height Stroke Application

Á Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁ Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁ Á Á Á Á Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Á
Wheel Cylinder Diameter: Caliper: Piston Diameter Master Cylinder: Bore Diameter Brake Rotors: Discard Thickness Lateral Runout (Installed) Rotor Diameter Rotor Thickness (New) Brake Drums: Inside Diameter Maximum Rebore Diameter Out-of-Round Application

DAEWOO M-150 BL2

FASTENER TIGHTENING SPECIFICATIONS

GENERAL SPECIFICATIONS

Capacity

Type

SPECIFICATIONS

18 26 18 26 NSm 25.5 18 16

9 12

Millimeters

6 10 200 30

17.46

20.64

10 0.05 236 12.7

180 182 0.04

48

HYDRAULIC BRAKES 4A 13

0.8 SOHC Engine

DOT3 or DOT4

0.45 L (0.48 qt.)

13 20 13 20 Lb-Ft 19.1 13 12

0.24 0.31 7.87 1.18

Inches

7.09 7.17 0.0016

0.4 0.002 9.3 0.5

0.69

1.89

0.81

80 106 Lb-In

4A 14 HYDRAULIC BRAKES

SCHEMATIC AND ROUTING DIAGRAMS
BRAKE LAMP WARNING CIRCUIT

D17A201B

STOPLAMP SWITCH CIRCUIT

D17A202B

DAEWOO M-150 BL2