Text preview for : M39b Lighting Systems.pdf part of Daewoo Matiz Service Manual, Wiring Diagram - 16 Part File - 62 File



Back to : 796cc (My 2003).part01.ra | Home

SECTION 9B

LIGHTING SYSTEMS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise noted.

TABLE OF CONTENTS
Description and Operation . . . . . . . . . . . . . . . . . . Headlamps and Parking Lamps . . . . . . . . . . . . . Front Turn Signal Lamps . . . . . . . . . . . . . . . . . . . Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . Taillamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . License Plate Lamp . . . . . . . . . . . . . . . . . . . . . . . . Interior Courtesy Lamp . . . . . . . . . . . . . . . . . . . . . Backup Lamp(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . Daytime Running Lamps (DRL) (W/Europe Only) . . . . . . . . . . . . . . . . . . . . . . . . Diagnostic Information and Procedures . . . . . Headlamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turn Signal Lamps and Hazard Lamps . . . . . . . Stoplamps and Interior Courtesy Lamp . . . . . . . Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . Repair Instructions . . . . . . . . . . . . . . . . . . . . . . . . . Headlamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9B-2 9B-2 9B-2 9B-2 9B-2 9B-2 9B-2 9B-2 9B-2 9B-3 9B-3 9B-4 9B-5 9B-6 9B-7 9B-7 CHMSL Mounting Bracket . . . . . . . . . . . . . . . . . License Plate Lamps . . . . . . . . . . . . . . . . . . . . . . Door Jamb Switch . . . . . . . . . . . . . . . . . . . . . . . . Interior Courtesy Lamp . . . . . . . . . . . . . . . . . . . . Daytime Running Lamp Module (W/Europe Only) . . . . . . . . . . . . . . . . . . . . . . . Ashtray Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . Luggage Room Lamp . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bulb Usage Chart . . . . . . . . . . . . . . . . . . . . . . . . Schematic and Routing Diagrams . . . . . . . . . . Backup Lamp(s) Circuit . . . . . . . . . . . . . . . . . . . Headlamps Circuit . . . . . . . . . . . . . . . . . . . . . . . . Headlamp Leveling Circuit . . . . . . . . . . . . . . . . . Tail and Licence Plate Lamps Circuit . . . . . . . . Stoplamps Circuit . . . . . . . . . . . . . . . . . . . . . . . . Turn and Hazard Lamps Circuit . . . . . . . . . . . . 9B-12 9B-12 9B-13 9B-13 9B-14 9B-14 9B-15 9B-16 9B-16 9B-17 9B-17 9B-18 9B-19 9B-20 9B-21 9B-22

Turn Signal Lamps . . . . . . . . . . . . . . . . . . . . . . . . 9B-8 Side Turn Signal Lamps . . . . . . . . . . . . . . . . . . . . 9B-8 Taillamps Assembly . . . . . . . . . . . . . . . . . . . . . . . . 9B-9 Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 9B-9 Rear Fog/Backup Lamp(s) . . . . . . . . . . . . . . . . . 9B-10 Center High-Mounted Stoplamp . . . . . . . . . . . . 9B-11

Interior Courtesy Lamp Circuit . . . . . . . . . . . . . . 9B-23 Front Fog Lamp Circuit . . . . . . . . . . . . . . . . . . . . 9B-24 Rear Fog Lamp Circuit . . . . . . . . . . . . . . . . . . . . 9B-25 Dimmer Control Circuit (Except W/Europe) . . 9B-26 Daytime Running Lamps Circuit (W/Europe Only) . . . . . . . . . . . . . . . . . . . . . . . 9B-27

DAEWOO M-150 BL2

9B ­ 2 LIGHTING SYSTEMS

DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever located on the left side of the steering column. They will come on with the ignition switch in any position. Turning the headlamp switch to the first position turns on the parking lamps, the license plate lamps and the instrument panel illumination. Turning the switch to the second position turns on all of the previous lamps and the headlamps. Turning the switch to the off position turns off all the lamps. The parking lamps can be turned on by turning the lighting switch to the first position. The parking lamps can be turned off by turning the switch to the OFF position. Headlamp high beam and low beam are also controlled by this lever. When the headlamps are on, pushing the lever away from the driver until the switch clicks changes the lamp from low beam to high beam. An indicator lamp on the instrument cluster assembly will come on when the high beam headlamps are on. To return the headlamps to low beam, pull the lever toward the driver. The headlamps must be aimed for proper illumination of the road. Headlamp aim should be checked whenever a new headlamp assembly is installed or service repairs to the front end area may have disturbed the headlamp assembly or its mountings.

TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp (if equipped with) and turn signal lamps are one assembly. Turning on either the headlamps or the parking lamps will also turn on the taillamps. When the brake pedal is pushed, the taillamps will glow brighter to serve as stoplamps. The center high-mounted stoplamp is located in the rear window and will come on when the brake pedal is pressed.

LICENSE PLATE LAMPS
The license plate lamps will come on when the headlamps or the parking lamps are on. The license plate lamps are mounted on the rear bumper, above the license plate.

INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just before the front seats. The lamp switch has three positions. If the switch is in the center position, the lamp will go on whenever a door is opened and go off when it is closed. In the ON position, the lamp will stay on until it is turned off. In the OFF position, the lamp will not come on, even when a door is opened.

FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal lamps flash to signal a turn. The turn signal works only when the ignition switch is on. The turn signals are controlled by the light switch on the left side of the steering column. Moving the lever all the way up or down (past the detent) will turn on the turn signals. When the turn is completed, the lever will return to horizontal and the turn signals will stop flashing. For changing lanes or shallow turns where the steering wheel does not turn far enough to cancel the signal, move the signal only to the first detent and hold it there. When the lever is released, it will return to horizontal and the turn signal will cancel.

BACKUP LAMP(S)
The backup lamps are located in the rear combination lamps. They will come on when the transaxle is shifted into REVERSE. On a vehicle with a manual transaxle, they are activated by a reverse switch which is part of the transaxle.

DAYTIME RUNNING LAMPS (DRL) (W/Europe Only)
The daytime running lamps (DRL) work in conjunction with the exterior lamps system. When the ignition switch is turned to the "II" position with the light switch off, parking, tail, license plate and instrument panel lights illuminate. And, when the engine is started, the headlamps (low beam) also come on. They remain on until the ignition switch is turned off or the light switch is turned on. They revert to normal operation when the light switch is on. The daytime running lamps (DRL) is optional.

REAR FOG LAMP
The rear fog lamp is incorporated in the drive side taillamp assembly and are controlled by the rear fog lamp switch on the instrument panel. The rear fog lamp can be turned on only when headlamps are on.

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 3

DIAGNOSTIC INFORMATION AND PROCEDURES
HEADLAMPS
Condition Low Beam Headlamps Are Inoperative, High Beam Headlamps Are OK. Probable Cause D Faulty headlamp combination switch. D The open circuit or a short circuit between the fuse Ef10/Ef11 and the terminal 5 of the headlamp combination switch. D Fuse Ef10 or Ef11 is blown. D The open circuit or a short circuit between the fuse Ef10 or Ef11 and the terminal 2 of the headlamp connector. D Headlamp bulb is blown. D The open grounds (G101, G102) circuit. High Beam Headlamps Are Inoperative, Low Beam Headlamps Are OK. D Faulty headlamp combination switch. D The open circuit or a short circuit between the fuse Ef8/Ef9 and the terminal 4 of the headlamp combination switch. D Fuse Ef8 or Ef9 is blown. D The open circuit or a short circuit between the fuse Ef8 or Ef9 and the terminal 1 of the headlamp connector. D Headlamp bulb is blown. D The open grounds (G101, G102) circuit. High Beam and Low Beam Headlamps Are Inoperative On Both Left and Right Sides. D The open circuit or a short circuit in the power supply circuit to the fuse Ef18. D Fuse Ef18 is blown. D The open circuit or a short circuit between the fuse Ef18 and the terminal 86, 30 of the headlamp relay. D Faulty headlamp relay. D The open circuit or a short circuit between the terminal 87 of the headlamp relay and the terminal 6 of the headlamp combination switch. D Faulty headlamp combination switch. D The open ground (G201) circuit. Correction D Replace the headlamp combination switch. D Repair or Replace the wiring harness.

D Replace the fuse Ef10 or Ef11 D Repair or Replace the wiring harness.

D Replace the headlamp bulb. D Repair or replace the open ground circuit. D Replace the headlamp combination switch. D Repair or Replace the wiring harness.

D Replace the fuse Ef10 or Ef11. D Repair or Replace the wiring harness.

D Replace the headlamp bulb. D Repair or Replace the open ground circuit. D Repair or Replace the wiring harness. D Replace the fuse Ef18 (20A). D Repair or Replace the wiring harness.

D Replace the headlamp relay. D Repair or Replace the wiring harness.

D Replace the headlamp combination switch. D Repair or Replace the open ground circuit.

DAEWOO M-150 BL2

9B ­ 4 LIGHTING SYSTEMS

TURN SIGNAL LAMPS AND HAZARD LAMPS
Condition Turn Signal Lamps and Hazard Lamps Do Not Work. Probable Cause D The open circuit or a short circuit between the power supply circuit and the fuse Ef2. D Fuse Ef2 is blown. D The open circuit or a short circuit between the fuse Ef2 and the fuse F12. D Fuse F12 is blown. D The open circuit or a short circuit between the fuse F12 and the terminal 8 of the hazard lamp switch connector. D Faulty hazard lamp switch. D The open circuit or a short circuit between the terminal 7 of the hazard lamp switch connector and the terminal 49 of the turn signal lamp relay. D The open circuit or a short circuit between the terminal 49a of the turn signal lamp relay and the terminal 9 of the hazard lamp switch connector. D Faulty turn signal lamp relay. D The open circuit or a short circuit between the terminal 49a of the turn signal lamp relay and the terminal 2 of the turn signal lamp switch connector. D Faulty turn signal lamp switch. D The open circuit or a short circuit between the terminal 1,3 of the turn signal switch connector and the terminal 2,5 of each turn signal lamp connectors. D Turn signal lamp bulb is blown. D The open grounds (G101, G102, G401, G402) circuits. Hazard Lamps Do Not Operate, Turn Signals Are OK. D The open circuit or a short circuit between the terminal 49a of the turn signal lamp relay and the terminal 9 of the hazard lamp switch connector. D The open circuit or a short circuit between the terminals 5,6 of the hazard lamp switch connector and the terminals 2,5 of the turn signal lamp connectors. D Replace the turn signal lamp switch. D Repair or Replace the wiring harness. Correction D Repair or Replace the wiring harness. D Replace the fuse Ef2. D Repair of Replace the wiring harness. D Replace the fuse F12. D Repair or Replace the wiring harness.

D Replace the hazard lamp switch. D Repair or Replace the wiring harness.

D Repair or Replace the wiring harness.

D Replace the turn signal lamp relay.

D Replace the turn signal lamp bulb. D Repair or Replace the open ground circuit. D Repair or Replace the open circuit.

D Repair or Replace the wiring harness.

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 5

STOPLAMPS AND INTERIOR COURTESY LAMP
Condition Stoplamps Do Not Work. Probable Cause D Fuse F5 is blown. D The open circuit or a short circuit between the fuse F11 and the terminal 2 of the stoplamps switch connector (For vehicle equipped with M/T). D Faulty stoplamp switch. D The open circuit or a short circuit between the terminal 1 of the stoplamp switch connector and the terminal 3 of the stoplamps connector (For vehicle equipped with M/T). D Stoplamp bulb is blown. D The open ground (G401, G402) circuits. Interior Courtesy Lamp Does Not Work. D The open circuit or a short circuit in the power supply circuit to the fuse Ef2. D Fuse Ef2 is blown. D The open circuit or a short circuit between the fuse Ef2 and the fuse F11. D Fuse F11 is blown. D The open circuit or a short circuit between the fuse F11 and the terminal 1 of the interior courtesy lamp connector. D Interior courtesy lamp bulb is blown. D Faulty interior courtesy lamp. Correction D Replace the fuse F5. D Repair or Replace the wiring harness.

D Replace the stoplamp switch. D Repair or Replace the wiring harness.

D Replace the stoplamp bulb. D Repair or Replace the open ground circuit. D Repair or Replace the wring harness. D Replace the fuse Ef2. D Repair or Replace the wiring harness. D Replace the fuse F11. D Repair or Replace the wiring connector.

D Replace the bulb. D Replace the interior courtesy lamp.

DAEWOO M-150 BL2

9B ­ 6 LIGHTING SYSTEMS

REAR FOG LAMP
Diagnostic Aids: The rear fog lamp will not operate unless the headlamps are ON. If the headlamps are not operating, repair that problem before attempting to diagnose the rear fog lamp. Condition Rear Fog Lamp Does Not Work. Probable Cause D The open circuit or a short circuit between the terminal 87 of the headlamp relay and terminal 15,30 of the rear fog lamp relay. D Faulty rear fog lamp relay. D The open circuit or a short circuit between the terminal 87 of the rear fog lamp relay and terminal 6 of the rear fog lamp connector. D The open circuit or a short circuit between the terminal E of the rear fog lamp relay and terminal 6 of the rear fog lamp switch. D Faulty rear fog lamp switch. D The open grounds (G201, G401) circuits. D Rear fog lamp bulb is blown. Correction D Repair or Replace the wiring harness.

D Replace the rear fog lamp relay. D Repair or Replace the wiring harness.

D Repair or Replace the wiring harness.

D Replace the rear fog lamp switch. D Repair or Replace the open ground circuit. D Replace the rear fog lamp bulb.

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 7

REPAIR INSTRUCTIONS ON­VEHICLE SERVICE
HEADLAMPS
Removal Procedure
1. Support the hood suitably. 2. Disconnect the negative battery cable. 3. Remove the front bumper spacer. D Remove the bolts (1). D Remove the front bumper spacer from the bumper fasia (2).

D209B109

4. Remove the headlamp. D Remove the bolts and washer (1). D Disconnect the electrical connectors. D Remove the headlamp (2) .

D19D502A

Installation Procedure
1. Install the headlamp with the bolts. 2. Connect the headlamp connector and parking lamp connector. 3. Install the front bumper spacer with the bolts. 4. Connect the negative battery cable.

D19D503A

DAEWOO M-150 BL2

9B ­ 8 LIGHTING SYSTEMS

TURN SIGNAL LAMPS
Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the front bumper spacer. Refer to Section 9M, Exterior Trim. 3. Remove the turn signal lamps from the front bumper spacer. D Disconnect the electrical connector (1). D Remove the screw (2). D Remove the turn signal lamp assembly (3).
D19D505A

Installation Procedure
1. Connect the electrical connector. 2. Install the turn signal lamp assembly with the screw. 3. Install the front bumper spacer. Refer to Section 9M, Exterior Trim. 4. Connect the negative battery cable.

D19D506A

SIDE TURN SIGNAL LAMPS
Removal Procedure
1. Disconnect the negative battery cable. 2. Slide the side turn signal lamp rearward. 3. Remove the lamp. 4. Disconnect the electrical connector.

D29B001

Installation Procedure
1. Connect the electrical connector. 2. Install the side turn signal lamp. 3. Connect the negative battery cable.

D29B002

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 9

TAILLAMPS ASSEMBLY
Removal Procedure
1. Disconnect the negative battery cable. 2. Open the tailgate. 3. Remove the luggage compartment wheelhouse trim. Refer to Section 9G, Interior Trim. 4. Disconnect the electrical connector.

D109D507

5. Remove the taillamp assembly. D Remove the screws (1). D Remove the taillamp (2).

D19D508B

Installation Procedure
1. Install the taillamp assembly with the screws. 2. Connect the electrical connector. 3. Install the luggage compartment wheelhouse trim. Refer to Section 9G, Interior Trim. 4. Connect the negative battery cable.

D19D509A

FRONT FOG LAMP
Removal Procedure
1. Disconnect the negative battery cable. 2. Raise and suitably support the vehicle. 3. Remove the front wheels. 4. Remove the front wheel house splash shield. D Remove the clip and bolts. a. Bolt and clips. D Remove the wheel house splash shield. b. Splash shield.
D19C501A

DAEWOO M-150 BL2

9B ­ 10 LIGHTING SYSTEMS
5. Remove the front fog lamp. D Remove the screws (1). D Disconnect the electrical connector (2). D Remove the front fog lamp (3).

D209B100

Installation Procedure
1. Install the front fog lamp with the screws. 2. Connect the front fog lamp connector. 3. Install the front wheelhouse splash shields with the clips and the bolts. 4. Install the front wheels. 5. Lower the vehicle. 6. Connect the negative battery cable.

D209B101

REAR FOG/BACKUP LAMP(S)
Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the taillamp assembly. Refer to "Taillamps Assembly" in this section. 3. Remove the bulb(s).

D19D508C

Installation Procedure
1. Install the bulb(s). 2. Install the taillamp assembly. Refer to "Taillamps Assembly" in this section. 3. Connect the negative battery cable.

D19D509A

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 11

CENTER HIGH-MOUNTED STOPLAMP (CHMSL)
Removal Procedure
1. Disconnect the negative battery cable. 2. Open the tailgate. 3. Pry off the tailgate trim panel. Refer to Section 9G Interior Trim. 4. Remove the CHMSL cover. D Remove the screws (1). D Remove the CHMSL cover (2).
D29B003B

5. Remove the CHMSL and bulb. D Remove the screws (1).

D29B004A

D Remove the screw from bulb socket (2). D Remove the CHMSL (3). D Remove the bulb (4).

D29B005B

Installation Procedure
1. Install the CHMSL bulb. 2. Install the CHMSL with the screws. 3. Install the CHMSL cover with the screws. 4. Install the tailgate trim panel. Refer to Section 9G, Interior Trim. 5. Connect the negative battery cable.

D19E554A

DAEWOO M-150 BL2

9B ­ 12 LIGHTING SYSTEMS

CHMSL MOUNTING BRACKET
Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the center high­mounted stoplamp (CHMSL). Refer to "Center High­Mounted Stoplamp" in this section. 3. Remove the rear window wiper motor assembly. Refer to Section 9D, Wipers/Washer Systems. 4. Remove the CHMSL mounting bracket. D Remove the bolts (1). D Remove the CHMSL mounting bracket (2).

D209B102

Installation Procedure
1. Install the CHMSL mounting bracket with the bolts. 2. Install the rear window wiper motor assembly. Refer to Section 9D, Wipers/Washer Systems. 3 .Install the CHMSL. Refer to "Center High­Mounted Stoplamp" in this section. 4. Connect the negative battery cable.

D209B103

LICENSE PLATE LAMPS
Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the license plate lamp from the tailgate handle. D Remove the screws (1). D Draw out the license plate lamp (2). D Remove the license plate lamp bulb (3).

D19D510A

3. Remove the rear window wiper motor assembly. Refer to Section 9D, Wipers/Washer Systems. 4. Disconnect the electrical connector in the tailgate. 5. Remove the tailgate handle. Refer to Section 9M, Exterior Trim. 6. Remove the license plate lamp socket. D Remove the socket (1).

D19D511A

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 13 Installation Procedure
1. Install the license plate lamp socket. 2. Install the tailgate handle. Refer to Section 9M, Exterior Trim. 3. Connect the electrical connector. 4. Remove the rear window wiper motor assembly. Refer to Section 9D, Wipers/Washer Systems. 5. Install the license plate lamp bulb. 6. Install the license plate lamp with the screws. 7. Connect the negative battery cable.
D19D512A

DOOR JAMB SWITCH
Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the door jamb switch. D Remove the screw (1). D Disconnect the electrical connector (2). D Remove the door jamb switch (3).

D109D513

Installation Procedure
1. Install the door jamb switch with the screw. 2. Connect the electrical connector. 3. Connect the negative battery cable.

D109D514

INTERIOR COURTESY LAMP
Removal Procedure
1. Disconnect the negative battery cable. 2. Remove the interior courtesy lamp. D D D D Pry off the interior courtesy lamp lens (1). Remove the screws (2). Disconnect the electrical connector (3). Remove the interior courtesy lamp (4).

D19D515A

DAEWOO M-150 BL2

9B ­ 14 LIGHTING SYSTEMS Installation Procedure
1. Connect the electrical connector. 2. Install the interior courtesy lamp with the screws. 3. Install the interior courtesy lamp lens. 4. Connect the negative battery cable.

D109D516

DAYTIME RUNNING LAMP MODULE (W/Europe Only)
Removal Procedure
1. Disconnect the negative battery cable. 2. Disconnect the electrical connector (1). 3. Remove the screws (2) and the daytime running lamp module.

D29B007

Installation Procedure
1. Install the daytime running lamp module with the bolts. 2. Connect the electrical connector. 3. Connect the negative battery cable.

D29B008

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 15

LUGGAGE ROOM LAMP
Removal Procedure
1. Disconnect the negative battery cable. 2. Open the tailgate. 3. Remove the luggage room lamp. D Remove the luggage room lamp (1). D Disconnect the electrical connector (2).

D209B104

Installation Procedure
1. Connect the electrical connector. 2. Install the luggage room lamp. 3. Connect the negative battery cable.

D209B105

DAEWOO M-150 BL2

9B ­ 16 LIGHTING SYSTEMS

SPECIFICATIONS
BULB USAGE CHART
Bulb Backup Lamp(s) Center High Mounted Stoplamp Headlamps Interior Courtesy Lamp License Plate Lamp Front Turn Signal Lamps Rear Fog Lamp Rear Turn Signal Lamps Side Marker Turn Signal Lamps Tail and Stoplamp Parking Lamp Replacement Bulb Number 21W 21W Double 60/55W 10W 5W 21W 21W 21W 5W Double 5/21W, 5W 5W

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 17

SCHEMATIC AND ROUTING DIAGRAMS
BACKUP LAMP(S) CIRCUIT

D19D201B

DAEWOO M-150 BL2

9B ­ 18 LIGHTING SYSTEMS

HEADLAMPS CIRCUIT

D19D202B

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 19

HEADLAMP LEVELING CIRCUIT

D19B723B

DAEWOO M-150 BL2

9B ­ 20 LIGHTING SYSTEMS

TAIL AND LICENSE PLATE LAMPS CIRCUIT

D19D203B

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 21

STOPLAMPS CIRCUIT

D19D204B

DAEWOO M-150 BL2

9B ­ 22 LIGHTING SYSTEMS

TURN AND HAZARD LAMPS CIRCUIT

D19D205B

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 23

INTERIOR COURTESY LAMP CIRCUIT

D19D206B

DAEWOO M-150 BL2

9B ­ 24 LIGHTING SYSTEMS

FRONT FOG LAMP CIRCUIT

D19B724A1

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 25

REAR FOG LAMP CIRCUIT

D19B724B

DAEWOO M-150 BL2

9B ­ 26 LIGHTING SYSTEMS

DIMMER CONTROL CIRCUIT (EXCEPT W/EUROPE)

D29B009A

DAEWOO M-150 BL2

LIGHTING SYSTEMS 9B ­ 27

DAYTIME RUNNING LAMPS CIRCUIT (W/EUROPE ONLY)

D29B010A

DAEWOO M-150 BL2