Text preview for : AN15VS Samtron 56V_56E Samsung 551V_S.pdf part of samsung 551v monitor samsung 551v
Back to : AN15VS Samtron 56V_56E Sa | Home
CONFIDENTIAL
COLOR MONITOR
Chassis AN15V* Model 551V, 551S 56V, 56E
SERVICE
COLOR MONITOR
Manual
CONTENTS
1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignment & Adjustments 5. Troubleshooting 6. Exploded View & Parts List 7. Electrical Parts List 8. Block Diagram 9. Wiring Diagram 10. Schematic Diagrams
CONFIDENTIAL
1 Precautions
1-1 Safety Precautions
WARNINGS 1. For continued safety, do not attempt to modify the circuit board. 2. 3. Disconnect the AC power before servicing. When the chassis is operating, semiconductor heatsinks are potential shock hazards. 3. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.
(READING SHOULD NOT BE ABOVE 0.5mA)
1-1-1
Servicing the High Voltage and CRT :
4.
WARNING:A high voltage adjusted to the wrong value may cause excessive X-ray emissions. 1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead. When troubleshooting a monitor with excessively HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage. High voltage should always be kept at the rated value, no higher. Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode. Do not lift the CRT by the neck.
2.
3.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES
LEAKAGE CURRENT TESTER
4.
2-WIRE CORD
5.
ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
EARTH GROUND
Figure 1-1. Leakage Current Test Circuit
6.
1-1-3 Product Safety Notices
Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment.
7.
1-1-2
Fire and Shock Hazard :
Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.
2.
AN15V*
1-1
1 Precautions
CONFIDENTIAL
1-2 Servicing Precautions
WARNING1: First read the "Safety Precautions" section of this manual. If unforeseen circumstances create conflict between the servicing precautions and safety precautions, always follow the safety precautions. WARNING2: A high voltage adjusted to the wrong value may cause excessive X-ray emissions. WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.
1. 2.
Servicing precautions are printed on the cabinet, and should be followed closely. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged.
5.
Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm.
6.
3.
7.
Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
4.
8.
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. Use only a grounded-tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficient to damage ESDs. 8. 6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD. Indicates ESDs on the Schematic Diagram in this manual.
7.
2.
3.
4. 5.
9.
1-2
AN15V*
CONFIDENTIAL
2 Product Specifications
2-1 Specifications
Item Picture Tube: Description 15-Inch (38 cm): 13.8-inch (35 cm) viewable, Full-square flat-face tube, 90° Deflection, Semi- tint, Non-glare, Invar shadow mask, Anti-static silica coating, 0.28 mm Dot pitch Horizontal 30 KHz ~ 55 KHz (Automatic) Vertical 50 Hz ~ 120 Hz (Automatic) Unlimited colors
Scanning Frequency Display Colors
Maximum Resolution Horizontal 1024 Dots Vertical 768 Lines Input Video Signal Input Sync Signal Maximum Pixel Clock rate Active Display Input Voltage Power Consumption Dimensions (W x D x H) With Base Weight (Net/Gross) Environmental Considerations Analog, 0.7 Vp-p positive at 75 , internally terminated Separate Sync : TTL level positive/negative 65 MHz Horizontal : 267 mm ± 4 mm, Vertical : 200 mm ± 4 mm AC 90 ~ 264 Volts, 60 Hz / 50 Hz ± 3 Hz 80 Watt (max) 14.01 x 14.92 x 14.54 Inches (356 x 379 x 369.5 mm) 11.5 kg (25.35 lbs) / Standard : 13.3 kg (29.32 lbs), Special : 13.4 kg (29.54 lbs) Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C) Humidity : 10 % ~ 80 % Storage Temperature : 4°F ~ 113°F (20°C ~ 45°C) Humidity : 5 % ~ 95 %
· Above models comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields. · Designs and specifications are subject to change without prior notice.
AN15V*
2-1
2 Product Specifications
CONFIDENTIAL
Sync Type
2-2 Pin Assignments
Separate Red Green Blue N-C GND (DDC Return) GND-R GND-G GND-B N-C GND-Sync./Self-Test N-C DDC Data H-Sync. V-Sync. DDC Clock
Macintosh GND-R Red H/V Sync. Sense 0 Green GND-G Sense 1 Reserved Blue Sense 2 GND V-Sync. GND-B GND H-Sync.
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
5
15
Figure 2-1. Male Type
Figure 2-2. Male Type
2-2
AN15V*
2 Product Specifications
CONFIDENTIAL
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1 Timing Chart Mode VGA3/60 Hz 640 x 480 31.469 31.778 3.813 1.907 25.422 0.636 59.940 16.683 0.064 1.048 15.253 0.318 25.175 IBM VGA2/70 Hz 720 x 400 31.469 31.778 3.813 1.907 25.422 0.636 70.087 14.268 0.064 1.080 12.711 0.413 28.322 640/75 Hz 640 x 480 37.500 26.667 2.032 3.810 20.317 0.508 75.000 13.333 0.080 0.427 12.800 0.027 31.500 VESA 640/85 Hz 640 x 480 43.269 23.111 1.556 2.222 17.778 1.556 85.008 11.764 0.671 0.578 11.093 0.023 36.000 800/85 Hz 800 x 600 53.674 18.631 1.138 2.702 14.222 0.569 85.061 11.756 0.056 0.503 11.179 0.019 56.250
Timing fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark
Negative Negative Separate
Negative Positive Separate
Negative Negative Separate
Negative Negative Separate
Positive Positive Separate
Separate Sync
Horizontal
Video Video
CC
Vertical
Video Video DD E
E Q
Q
RR
S S
Sync Sync B B AA
Sync Sync
PP
O O
A : Line time total C : Back porch E : Front porch AN15V*
B : Horizontal sync width D : Active time
O : Frame time total Q : Back porch S : Front porch
P : Vertical sync width R : Active time
2-3
2 Product Specifications
CONFIDENTIAL
Memo
2-4
AN15V*
CONFIDENTIAL
3 Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures for the AN15V* monitor. WARNING: This monitor contains electrostatically sensitive devices. Use with caution when handling these components.
3-1 Disassembly
Cautions:1. Disconnect the monitor from the power source before disassembly. 2. To remove the Rear Cover, you must use the special opening jig tool.
3-1-1 Before making Disassembly
1. Disconnect or power cord from the monitor. 2. With a pad beneath it, stand the monitor on its front with the screen facing downward and the base close to you.
4. Push the Opening jig each groove along the top of the monitor till it makes a "ttak" sound. (2 grooves : Left and Right, Make sure each snap is disengaged.)
3-1-2 Cabinet Disassembly
1. Remove the Stand from the monitor. (Refer to Stand manual) 2. Remove 2 screws on the Rear cover.
Figure 3 5. Pull the Rear Cover up off the monitor.
Figure 1 3. Incline the monitor by lifting the rear of the monitor.
Figure 4
Figure 2
AN15V*
3-1
3 Disassembly and Reassembly 6. Remove the Shield.(TCO 95)
CONFIDENTIAL
3-1-4 Removing the Main PCB
1. Complete all previous steps. 2. Disconnect the Degaussing Coil at CN603 on the Main PCB. 3. Disconnect all easily accessible ground wires on the PCB and Bottom Chassis. 4. Disconnect the DY connector at the CN404 connector on the Main . 5. Using the jig, release the snaps (2) connecting the Front Cover and the PCB then lift up the Bottom to separate the two Shield.
Figure 5 7. Using pinch-nose pliers or ling-nose pliers, acrefully disconnect the Anode Cap from the CRT. Warning: Do not touch the Anode contact on the CRT (High Voltage may remain).
3-1-3 Removing the CRT Socket PCB
1. Complete all previous steps. 2. Lift up the Video Spring and remove the CRT Socket PCB from the CRT.
Figure 7 6. Disconnect the Sub PCB connector at the CN201 connector on the Main PCB. 7. Remove the screws on the back and along each side of the Bottom Chassis. 8. Carefully lift the Main PCB Ass'y and remove the remaining ground wires. 9. Place the Main PCB Ass'y on a flat, level surface that is protected from static electricity.
3-1-5 CRT Ass'y Disassembly
Figure 6 3. Disconnect all connectors on the CRT Socket PCB. 4. Using a solder iron, disconnect Ground (GND) on the back of the Video Shield and remove the Shield Cap. 5. Remove the screw on the front of the Shield Socket. 6. Desolder the 4 tabs on the CRT Socket PCB and remove Shield. 7. Place the Video PCB on a flat, level surface that is protected from static electricity. 1. Complete all previous steps. 2. Straighten the Degaussing Coil Assembly coated metal ties and lift the Coil Ass'y from the CRT. 3. Remove the four corner screws and lift the CRT up and away from the Front Cover Assembly and place it on a padded surface. Caution: Do not lift the CRT by the neck. If you will be returning this CRT to the monitor, be sure to place the CRT face downward on a protective pad.
3-2 Reassembly
Reassembly procedures are in the reverse order of Disassembly procedures. 3-2 AN15V*
CONFIDENTIAL
4 Alignment and Adjustments
This section of the service manual explains how to make permanent adjustments to the monitor. Directions are given for adjustments using the monitor Interface Board Ver. 1.1 and software (Softjig).
4-1 Adjustment Conditions
Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the settings are not permanently stored and may be inadvertently deleted by the user.
4-1-1 Before Making Adjustments
4-1-1 (a) ORIENTATION When servicing, always face the monitor to the east. 4-1-1 (b) WARM-UP TIME The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments. 4-1-1 (c) SIGNAL Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: TTL level, negative/positive 4-1-1 (d) SCANNING FREQUENCY Horizontal: 30 KHz ~ 55 KHz (Automatic) Vertical: 50 Hz ~ 120 Hz (Automatic) Unless otherwise specified, adjust at the 800 x 600 mode (54 KHz/85 Hz).
4-1-2 Required Equipment
The following equipment may be necessary for adjustment procedures: 4-1-2 (a) DISPLAY CONTROL ADJUSTMENT 1. Non-metallic () screwdriver: 1.5, 2.5, 3 mm 2. Non-metallic (+) screwdriver: 1.5, 2.5, 3 mm 3. Digital Multimeter (DMM), or Digital Voltmeter 4. Signal generator, or DM200 software 5. Personal computer 4-1-2 (b) COLOR ADJUSTMENTS 1. All equipment listed in 4-1-2 (a), above 2. Color analyzer, or any luminance measurement equipment
AN15V*
4-1
4 Alignment and Adjustments
CONFIDENTIAL
4-2-3 (a-2) HORIZONTAL SIZE ADJUSTMENT Use control bar after selecting "H-SIZE" in left menu to adjust the horizontal size of the display pattern to 267 mm . (Tolerance: ± 4 mm.) 4-2-3 (b) VERTICAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 54 KHz/85 Hz Crosshatch pattern Maximum Maximum
4-2 Display Control Adjustments
4-2-1 HIGH VOLTAGE
Signal: 800 x 600 (54 KHz/85 Hz) Display image: Full White Pattern Contrast: Maximum Brightness: Maximum Limit: 25.0 kV ± 0.2 kV Measure the hight voltage level at the anode cap. High voltage should be within the limit as above.
4-2-2 CENTER RASTER
Adjust VR401 so that the back raster comes to the center when you apply each basic mode. SCREEN VOLTAGE ADJUSTMENT This can only SDI CRT conditions. Signal: 800 x 600 (54 KHz/85 Hz) Display image: Don't care Contrast: Minimum Brightness: Minimum Limit: 480 ± 10V Adjust screen VR of T501.
Use control bar after selecting "V-SIZE" in left menu to adjust the vertical size of the display pattern to 200 mm. (Tolerance: ± 4 mm.) 4-2-3 (c) HORIZONTAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 54 KHz/85 Hz Crosshatch pattern
4-2-3 Centering
Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display. Adjust the horizontal size and vertical size to their optimal settings: 267 mm (H) x 200 mm. Adjust the horizontal position and vertical position to 5.0 mm of the center point of the screen. |A B| 5.0 mm.
C DISPLAY AREA A B EDGE OF BEZEL D
Use control bar after selecting "H-POSITION" in left menu to center the horizontal image on the raster. 4-2-3 (d) VERTICAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 54 KHz/85 Hz Crosshatch pattern
Use control bar after selecting "V-POSITION" in left menu to center the vertical image on the raster.
|C D| 5.0 mm.
4-2-4 Linearity
Linearity affects the symmetry of images as they appear on the screen. Unless each row or column of blocks in a crosshatch pattern is of equal size, or within the tolerances shown in Table 4-1 an image appears distorted, elongated or squashed. X max-X min x100 X max+X min Y max-Y min Vertical Linearity = 2x x100 Y max+Y min Horizontal Linearity = 2x Table 4-1
Adjacent Linearity Entire Linearity Preset mode Pre-load mode (48kHz~)
Figure 4-3. Centering 4-2-3 (a-1) HORIZONTAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 54 KHz/85 Hz Crosshatch pattern Maximum Maximum
4% 5%
8% 14%
Use control bar after selecting "SIZE B+" in left menu to adjust the horizontal size of the display pattern to 255 mm . (Tolerance: ± 4 mm.)
Preset Mode : 54KHz / 85Hz Pre-load Mode : Refer to Timing Chart
4-2
AN15V*
4 Alignment and Adjustments 4-2-4 (a) HORIZONTAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 54 KHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Horizontal Linearity, refer to Table 4-1 for the tolerance range. Increase or decrease H_LIN to optimize the image. 4-2-4 (b) VERTICAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 54 KHz/85 Hz Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Vertical Linearity, refer to Table 4-1 for the tolerance range. Use control bar after selecting "V-LINEARITY BAL" in left menu to optimize the image.
CONFIDENTIAL
Use control bar after selecting "PINBALANCE" in left menu to optimize the image.
4-2-7 Parallelogram Adjustment
CONDITIONS Scanning Frequency: Display image: Brightness: Contrast: 54 KHz/85 Hz Crosshatch pattern Maximum Maximum
Use control bar after selecting "PARALLEL" in left menu to make the image area rectangular.
4 mm
Figure 4-6. Parallelogram
4-2-8 Side Pincushion Adjustment
CONDITIONS Scanning frequency: Display image: 54 KHz/85 Hz Crosshatch pattern
4-2-5 Trapezoid Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 54 KHz/85 Hz Crosshatch pattern Maximum Maximum
Use control bar after selecting "PINCUSHION" in left menu to straighten the sides of the image area.
| C1 |, | C2 | 2.0 mm, | D1 |, | D2 | 2.0 mm. C2
Use control bar after selecting "TRAPEZOID" in left menu to make the image area rectangular.
| A B | < 4 mm A A D1 D2
C1 B B
Figure 4-7. Pincushion
Figure 4-4. Trapezoid
4-2-9 Degauss
No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once per 30 minutes.
4-2-6 Pinbalance Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 54 KHz/85 Hz Crosshatch pattern Maximum Maximum
4-2-10 To Delete the User Mode Data
To delete the adjustment data from the user modes, click "@4: USER DELETE" in right ment.
| D1 |, | D2 | 2.0 mm
4-2-11 Save the Data
D1 D2 D1
To save the adjustment data for a mode, press "@3: ALL MODE SAVE" in right ment.
Figure 4-5. Pinbalance
AN15V*
4-3
4 Alignment and Adjustments
CONFIDENTIAL
4-3-2 (b) WHITE BALANCE ADJUSTMENT CONDITIONS Scanning frequency: 54 KHz/85 Hz Display image: White box pattern Brightness: 0.06ft-L at Back Raster Pattern Display Contrast: Maximum 1. Use control bar after selecting "RED GAIN", "GREEN GAIN" and "BLUE GAIN" to adjust the luminance to 50 ft-L with the color coordinates ranged for 9300K to x = 0.283 ± 0.015, y = 0.298 ± 0.015.
4-3 Color Adjustments
CAUTION : Check below condition before color adjustment Video signal : Analog 0.7 Vp-p (at 75 ) Sync : TTL level (H, V seperate signal) * Select "Color" in Softjig menu for color adjustment.
4-3-1 Color Coordinates (Temperature)
Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum. CONDITIONS Measurement instrument: Color analyzer Scanning frequency: 54 KHz/85 Hz Display image: White flat field at center of display area Luminance: Maximum PROCEDURE Use the directions in sections 4-3-2 through 4-3-3 to adjust the color coordinates for: 9300K to x = 0.283 ± 0.015, y = 0.298 ± 0.015 6500K to x = 0.313 ± 0.015, y = 0.329 ± 0.015
1/3H-1/2H FRONT BEZEL OPENING 1/3V-1/2V BACK RASTER WHITE WINDOW
Figure 4-8. White Box Pattern 4-3-2 (c) ABL ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 54 KHz/85 Hz Full white pattern Maximum Maximum
4-3-2 Color Adjustments for 9300K
4-3-2 (a) BACK RASTER COLOR ADJUSTMENT
FRONT BEZEL OPENING
CONDITIONS Scanning frequency: Display image: Brightness: Contrast:
BACK RASTER
54 KHz/85 Hz Back raster pattern Maximum Maximum
WHITE WINDOW
1. Select "@1: CHANNEL 1" in right menu to control the color for 9300K. 2. Adjust the luminance of the back raster to between 0.5 to 0.7 ft-L using contron bar after selecting "GREEN CUTOFF" in the menu. 3. Use control bar after selecting "BLUE CUTOFF" in left menu to set the "y" coordinate to 0.298 ± 0.015 4. Use control bar after selecting "RED CUTOFF" in left menu to 0.283 ± 0.015 * If color values would not be matched desirable values, repeat sequence 3 and 4 after readjusting "GREEN CUTOFF" control a little different. 4-4
Figure 4-9. Full White Pattern 1. Check the ABL. If it is not within the specifications, use the ABL controls to adjust it. (38 ± 1 ft-L ) 2. Select "@4: COLOR SAVE" to save the data. 3. Select "@6: ALL COLOR SAVE" to save the CH2. 4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION CONDITIONS Scanning frequency:
54 KHz/85 Hz
AN15V*
4 Alignment and Adjustments Display image: X-Y Coordinates: ABL Luminance Brightness: Contrast: Back raster pattern Full White Pattern x = 0.283 ± 0.015, y = 0.298 ± 0.015 Refer to 4-3-2(c) Maximum 5 ft-L, 24 ft-L
CONFIDENTIAL
4-3-4 Focus Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 54 KHz/85 Hz (800 x 600) "H" character pattern Cut off point Maximum
1. Check whether the color coordinates of the back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. 2. Display a full white pattern. 3. Select "Geometry" in softjig menu. 4. Select "@7: 5-ft " in right menu. 5. Check whether the white coordinates of the video meet the above coordinates spec. 6. Select "@8: 24-ft " in right menu. 7. Check whether the white coordinates of the video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. Select "Color" and click "@2: CHANNEL 2" for color ajdustment for 6500K Repeat the sequence of 9300K adjustment. The luminance values the same as 9300K, but the color coordinated of back raster and white box are : x = 0.313 ± 0.015 y = 0.329 ± 0.015
PROCEDURE 1. Adjust the Focus VR on the FBT to display the sharpest image possible. 2. Use Locktite to seal the Focus VR in position.
4-3-5 Color Purity Adjustment
Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface. CONDITIONS Orientation: Scanning frequency: Display image: Luminance:
Monitor facing east 54 KHz/85 Hz White flat field Cut off point at the center of the display area
Note: Color purity adjustments should only be attempted by qualified personnel. PROCEDURE For trained and experienced service technicians only. Use the following procedure to correct minor color purity problems: 1. Make sure the display is not affected by external magnetic fields. 2. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm ± 1 mm. 3. Display a green pattern over the entire display area. 4. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. (Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015)
Red: Green: Blue: x = 0.640 ± 0.015 x = 0.295 ± 0.015 x = 0.142 ± 0.015 y = 0.323 ± 0.015 y = 0.594 ± 0.015 y = 0.066 ± 0.015
4-3-3 Luminance Uniformity Check
Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10. CONDITIONS Scanning frequency: Display image: Brightness: Contrast:
54 KHz/85 Hz (800 x 600) White flat field Cut off point at 24 ft-L Maximum
PROCEDURE Measure luminance at nine points on the display screen (see figure below).
Table 4-2. Color Purity Tolerances
(For 9300K color adjustment: x = 0.283 ± 0.015, y = 0.298 ± 0.015)
Figure 4-10. Luminance Uniformity Check Locations AN15V*
5. When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping. 4-5
4 Alignment and Adjustments
CONFIDENTIAL
Memo
4-6
AN15V*
CONFIDENTIAL
5 Troubleshooting
5-1 Parts Level Troubleshooting
Notes: Check the following circuits. · No raster appears: Power circuit, Horizontal output circuit. · High voltage develops but no raster appears: Video output circuits. · High voltage does not develop: Horizontal output circuits.
5-1-1 No Power Supply
Check and replace D601 and FH_1.
WAVEFORMS
1 100 V (IC601, #1)
Chirping noise exists?
Yes
Check and replace IC601.
No Repeating start? Yes Check and replace D606.
CH1 P-P = 100 V CH1 RMS = 350.2 V
No
1
IC601 Pin 1 waveform is right?
No
Check and replace Q602, IC605, OP202 and IC602.
Yes C622 Voltage is 13 V ± 0.5V? No Check and replace IC201, IC301, IC401, IC605, Q402, Q404, Q613,and Q614.
Yes Operate normally? No Replace Main board.
Yes Verify voltages.
Done.
AN15V*
5-1
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
2 100 V (IC601, #1)
5-1-2 DPMS Failure
Check signal source H/V Sync. video level.
Make No H/V Sync. (power off mode)
LED blinks?
No
Check IC201 Pin 40.
CH1 P-P = 100 V
CH1 RMS = 325.8 V
Yes +12 V line off? No Check IC201 Pin 5, Pin 6 and Q610, Q602 operation condition.
Yes Q602 Base voltage exists? Yes Done No Refer to 5-1-1 No Power Supply.
2
IC601 Pin 1 Output voltage exists?
No
Check IC201 Pin 5. Check and replace Q602 and IC201.
5-2
AN15V*
5 Troubleshooting
CONFIDENTIAL
No Does DC 12V appear at Pin 29 of IC605? Yes Check IC605. No Check 12 V line.
5-1-3 H_Deflection Failure
Does PWM output signal appear at Pin 28 (B_drv) of IC605? Yes
3
WAVEFORMS
3 5.00 V (IC605, #28)
4
Does Horizontal pluse signal appear at at Pin 26 of IC605? Yes
No
Check IC605.
5
Does 20 Vp-p signal appear at Collector of Q400? Yes Check D406, Q404 and T401.
No
Check Q400.
4 1.00 V (IC605, #26)
5 5.00 V (Q400, Collector)
5-1-4 S Correction Failure
Check S1 ~ S2 signal.
S1~S2 signals are right at each frequency block? Yes Check and replace Q404, Q410, Q411, Q415, and Q416.
No
Check and replace IC201.
AN15V*
5-3
5 Troubleshooting
CONFIDENTIAL
Check and replace T402
5-1-5 H_Lin. Failure 5-1-6 Invariable H_Size
IC605 Pin 28 voltage varies with different B_Drv DAC values? Yes
No
Check and replace IC605.
Q402 Gate output duty varies with different B_Drv DAC values?
No
Check some parts around Q402, IC605 Pin 4 ~ 6.
5-1-7 Abnormal H_Size
IC605 Pin 24 output duty varies with different B+ offset DAC values? Yes
6
No
WAVEFORMS
Check and replace IC201. 6 5.00 V (Q408, Collector)
Q408 Collector waveform is right? Yes Check some parts around D409 and L401.
No
Check and replace Q405, Q406, Q407, and Q408.
5-4
AN15V*
5 Troubleshooting
CONFIDENTIAL
No Check and replace IC605.
5-1-8 Side Pin or Trap Failure WAVEFORMS
7 1.00 V (IC605, #24) Yes Refer to 5-1-7 Abnormal H_Size.
7
IC605 Pin 24 output exists?
5-1-9 Para. or Pin Balance Failure
IC605 Pin 24 output varies with different DAC values? No Replace IC605. Yes
Refer to 5-1-7 Abnormal H_Size.
AN15V*
5-5
5 Troubleshooting
CONFIDENTIAL
No Refer to 5-1-1 No Power Supply
5-1-10 V Deflection Failure WAVEFORMS
8 1.00 V (IC605, #23) Yes
8
13V and 10V lines are on?
IC605 Pin 23 output exists?
No
Check and replace IC605.
Yes
9
IC300 Pin 6 output exists?
No
Check and replace some parts around IC300.
9 10.0 V (IC300, #6)
Yes Check DY connector connection.
5-1-11 V Size or Position Variation Failure
IC605 Pin 23 output varies with different DAC values? Yes Check and replace IC300. No
Check and replace IC201 and IC605.
5-6
AN15V*
5 Troubleshooting
CONFIDENTIAL
No Check and replace IC605 and +12 V line.
5-1-12 High Voltage Failure WAVEFORMS
3 5.00 V (IC605, #28) Yes
10
3
IC605 Pin 28 OSC pulse exists?
Q402 Gate driving pulse exists?
No
Check and replace Q401, Q417.
Yes
11
Q402 Drain pulse exists?
No
Check and replace Q402, D401 Check 50V line and L402.
CH1 P-P = 2.00 V CH1 RMS = 5.868 V
10 5.00 V (Q402, Gate)
Yes Done
CH1 P-P = 2.00 V CH1 RMS = 7.692V
5-1-13 ABL Failure
11 50.0 V (Q402, Drain)
Input full white pattern to monitor.
IC101 Pin 8 input exists and varies with different patterns? Yes Check CN102.
No
Check and replace IC101.
CH1 P-P = 50.0 V
CH1 RMS = 73.7V
T501 Pin 8 output exists?
No
Check and replace T501.
Yes IC201 Pin 26 output exists and varies with different patterns? Yes Done No Check and replace IC201.
AN15V*
5-7
5 Troubleshooting
CONFIDENTIAL
No Replace the C432.
5-1-14 Dynamic Focus Failure (This comonly TSB CRT)
T502 Pin 6 output is right?
12
WAVEFORMS
12 50.0 V (T502, #6)
Yes
13
T502 Pin 1 input is right?
No
Check and replace T502.
Yes Check the connection between FBT Focus pin and CRT Socket PCB.
CH1 P-P = 50.0 V CH1 RMS = 75.6 V
13 100 V (T502, #1)
CH1 P-P = 100V CH1 RMS = 124.0 V
5-8
AN15V*
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
14 1.00 V (IC101 #12,14,16)
5-1-15 No Video
Check signal cable and connection.
14
IC101 Pin 12, 14 and 16 inputs are right? Yes
No
Check the signal cable connection.
15
IC101 Pin 18, 21 and 24 outputs are right? Yes
No
Check I2C bus and +12V line. 15 0.5 V (IC101 #18,21,24)
16
IC102 Pin 9, 10 and 11 outputs are right? Yes Cathode DC levels are right?
No
Check +12V, +80V line. Check and replace IC102.
No
Check +80V line. Check and replace IC104.
16 20.0 V (IC102, #9,10,11)
Yes G2 voltage is right? No Check G2 wire, CRT Socket board and FBT.
Yes Change CRT.
Done.
AN15V*
5-9
5 Troubleshooting
CONFIDENTIAL
No Check Q608.
5-1-16 Micom Failure WAVEFORMS
17 2.00 V (IC201, #13, 14) Yes
17
IC201 Pin 11 input voltage is 5V?
IC201 Pin 13 and 14 inputs are right? Yes IC201 Pin 18 input is right?
No
Check C202, C203 and X201.
No
Check and replace IC201 and R206.
Yes All in/output values are right? No Replace IC201.
Yes Done
5-10
AN15V*
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
18 2.00 V (IC101, #32) No Check CN102 Pin 14. Check and replace R117, C117 and IC101.
5-1-17 OSD Failure
Check CN102 and connector Assy.
18
IC101 Pin 32 input is right?
Yes
19
IC101 Pin 1 input is right?
No
Check CN102 Pin 8. 19 2.00 V (IC101, #1)
Yes IC101 Pin 29 and 30 inputs are right? Yes
20
No
Check IC201 Pin 41 and 42.
IC101 Pin 18, 21 and 24 outputs are right? Yes Check and replace IC102.
No
Check and replace IC101.
20 1.00 V (IC101, #18,21,24)
Done
AN15V*
5-11
5 Troubleshooting
CONFIDENTIAL
No Check the button. (SW201 ~ SW204)
5-1-18 User Control Failure
Does the DC level change at Pin 38 of IC201 when you push the button S/W? Yes Check IC201.
5-1-19 Degaussing Failure
Check degaussing connector.
RL601 operation is right?
No
Check D-coil and TH601.
Yes Q601 base input is right? No Check and replace Q601.
Yes IC201 Pin 4 output is right? No Check and replace IC201.
Yes Done
5-12
AN15V*
5 Troubleshooting
CONFIDENTIAL
5-2 General Troubleshooting
5-2-1 No Picture
No
LED blinks?
Refer to 5-2-2 Shut down.
Yes LED is green color? No Check Micom.
Yes Check G2 voltage, high voltage and R, G, B cathode voltage.
5-2-2 Shut Down
Blinking LED's?
No
Check power supply.
Yes Scan failure? Yes Check horizontal, vertical deflection system and check power supply secondary voltages.
No Video failure? Yes Check Video board.
No Check and replace IC201.
Done
AN15V*
5-13
5 Troubleshooting
CONFIDENTIAL
No Check signal generator.
5-2-3 Missing Color
Proper Video levels are on CN101 (D-Sub) Pin 1, 3 and 5? Yes
21
WAVEFORMS
21 10.0 V (R,G,B, Video)
Proper Video signal is on all cathodes? Yes Proper DC voltage is on all cathodes? Yes G2 voltage is right? Yes Heater voltage is right?
No
Refer to 5-1-15 No Video.
No
Check IC101 Pin 17, 20 and 23. Check IC104.
CH1 P-P = 10.0V
CH1 RMS = 17.02V
No
Check T501.
No
Check D608, Q604 and T601.
Yes G1 voltage is right? Yes Replace CRT. No Check D504, Q502 and T501.
Done
5-14
AN15V*
5 Troubleshooting
CONFIDENTIAL
WAVEFORMS
22 5.00 V (Q502, Collector) No
5-2-4 Visible Retrace
Check white balance adjustment.
G2 voltage is right?
Check T501.
Yes Blank pulse is on Pin 3 of IC605? No Check IC605. 23 50.00 V (CRT Socket, G1) Yes
22
V_FLB pulse is on Collector of Q502? Yes
No
Check Q502.
23
Does approve the Vertical pulse on the CRT Socket G1? Yes Done
No
Check CN102 and CN201.
AN15V*
5-15
5 Troubleshooting
CONFIDENTIAL
5-2-5 Unsynchronized Image
Check input signals Pin 2 and 3 of CN202.
Signals are right?
No
Check Video Cable.
Yes Signals at Pin 28 and 29 of IC201 are right? Yes Signals at Pin 1 and 2 of IC605 are right? Yes Check circuits on Main board. No Check IC605. No Check IC201.
Done
5-16
AN15V*
5 Troubleshooting
CONFIDENTIAL
5-2-6 Misconvergence
Try readjusting convergence.
The convergence is now within spec.? No Readjust convergence.
Yes
Done
The convergence is now within spec.? No Change CRT and readjust convergence.
Yes
Done
Done
AN15V*
5-17
5 Troubleshooting
CONFIDENTIAL
5-2-7 Poor Focus
Adjust focus VR of FBT.
Improved focus?
Yes
Aging monitor and check for focus change.
No Check focus leads from FBT to CRT Socket.
Check the CRT Socket.
(Toshiba CRT)
Dynamic focus circuit is right?
No
Refer to 5-1-14 Dynamic Focus Failure.
(SDI CRT)
Yes
Replace the CRT and verify focus.
5-2-8 Purity Failure
Degaussing
Purity is right?
Yes
Done
No Degaussing circuit is right? No Refer to 5-1-19 Degaussing Failure.
Yes Replace CRT and verify purity.
5-18
AN15V*
CONFIDENTIAL
6 Exploded View and Parts List 6-1 AN15VS
AN15V*
6-1
6 Exploded View & Parts List
CONFIDENTIAL
6-2 AN15VT
6-2
AN15V*
CONFIDENTIAL
7 Electrical Parts List
7-1 Main PCB Parts
Loc. No. AN_LABEL C409 C419 C601 C602 C608 CIS CIS1 CIS11 CIS12 CIS13 CIS14 CIS15 CIS16 CIS2 CIS21 CIS22 CIS3 CIS31 CIS4 CIS5 CN201 CN202 CN404 CN502_WIRE CN601 CN604 D406 D409 D601 D608 D609 FBT_CORE FBT+H/S FUSE IC_SOCKET IC605 L401 L402 L403 L601 OP201 OP202 Q410 Q411 RL601 SH/B+AC/SK SH/B+GND SH/B+PCB SH/B+SH/LM SW601 T401 T402 T501 T601 T602 TH601 Code No. BH94-00827C BH68-00446D 2306-000248 2301-001206 2301-001195 2301-001195 2401-003392 BH39-00405A 0201-001096 BH71-00110A BH68-00001A BH72-00025A BH72-00026A BH72-00261A BH73-60304C 0202-001044 6502-000001 6502-000001 0202-001046 BH39-00323D 0202-001222 0204-001095 3711-003895 3711-003873 3711-003989 BH39-00401A 3721-001053 BH39-00288A 0402-001025 0402-001295 0402-000103 0402-000016 0402-001295 3301-000233 6003-000122 3601-001302 3704-001071 1204-002013 BH27-00131A BH27-00131A BH27-20342U BH29-00002A 0601-001147 0604-001018 0505-001676 0505-001675 3501-001111 6003-000010 6003-000010 6003-000010 6003-000010 3403-001132 BH26-00027A BH27-00137A BH26-00140A BH26-00145A BH26-00141A 1404-001264 Description ASSY PCB MAIN LABEL C-FILM,MPPF C-FILM,PPF C-FILM,MPPF C-FILM,MPPF C-AL CBF SIGNAL ADHESIVE-HM SHIELD BOTTOM LABEL-MARK CDT GUIDE-POWER SHAFT-POWER SHEET ABS-LMF RUBBER-SUPPORT SOLDER-WIRE. CABLE CLAMP CABLE CLAMP SOLDER-WIRE FLUX LEAD CONNECTOR-ASSY SOLDER-WIRE FLUX THINNER CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER LEAD CONNECTOR-ASSY PLUG-AC POWER CBF HARNESS DIODE-RECTIFIER DIODE-RECTIFIER DIODE-BRIDGE DIODE-RECTIFIER DIODE-RECTIFIER CORE-FERRITE SCREW-TAPTITE FUSE-AXIAL LEAD SOCKET-IC IC-DEF. PROCESSOR COIL CHOKE COIL CHOKE COIL-CHOKE FILTER LINE NOISE LED PHOTO-COUPLER FET-SILICON FET-SILICON RELAY-POWER SCREW-TAPTITE SCREW-TAPTITE SCREW-TAPTITE SCREW-TAPTITE SWITCH-PUSH TRANS-HOR.DRIVE COIL LINEARITY TRANS FBT TRANS SWITCHING TRANS-SYNC THERMISTOR-PTC Specification AN15VS AN-STICKER,ART-PAPER 100G,15,15,BLACK,YELLOW 680nF,5%,250V,BK,26.5x16.5mm,2 4.4nF,5%,2.5KV,BK,29x21x13,20 150nF,10%,275VAC,BK,26x16.5x7, 150nF,10%,275VAC,BK,26x16.5x7, 180uF,20%,450V,GP,BK,25x45,10 AN15/17**,15P/06P,07P,20276-N,1500MM,UL20276,IVORY,D-SUB/MALE,ATT. TYPE #3748,YEL,8500CPS,PN15VT,SECC ,T1.0 ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT CDA4507,ABS,V0,IV16 CDA4507,ABS,V0,IV16 IB10LO,AL+PET,-,-,-,-,-,DP15LT,CR V0,GRAY,-,14*7*10,-,S63S-W3.0,S63S,D3,63Sn/37Pb,DAWH-5NB,D15,L35,NYLON66,NTR DAWH-5NB,D15,L35,NYLON66,NTR CF-110VH-2A,-,-,-,OT17LO,8.0*0.16TA*16,35068-9822,35750-1010,BK,150MM,8.0*0.16TA*16 RS-107,RS60-1.2AA,D1.2,SN60/PB40,#4520,-,-,BOX,13P,1R,2mm,STRAIGHT,SN BOX,7P,1R,2mm,STRAIGHT,SN NOWALL,4P,1R,8mm,STRAIGHT,SN DT15LT,UL1007#22,UL/CSA,3(2)P,BLK,#22,YBNH250-03,BK,170MM,1007#22 3P,-,-,NI PN17LO,UL1007,UL/CSA,2P/2P,130MM,BLU/WHT,AWG26,YBNH200,SMP250,-,-,-,-,-,-,CBF-CO ERD07-15,1.5KV,1.5A,-,TP GUR460L-5700,600V,4A,DO-201AD,BK D2SBA60,600V,1.5A,SIP-4,ST UF5404,400V,3A,DO-201AD,TP GUR460L-5700,600V,4A,DO-201AD,BK ZZ,18x9.5x28mm,-,BH,+,B,M4,L12,ZPC(YEL),SWRCH18 250V,3.15A,SLOW-BLOW,CERAMIC,5X20MM 42P,DIP,SN,1.778mm STV6888,DIP,32P,400MIL,PLASTIC,13.2V,-,0TO+70C,ST,100KHZ 150UH,AN17K,150UH,10%,0.35OHM,2.5A,AR8X25,72.5TS,18X39MM,11MM,BK 150UH,AN17K,150UH,10%,0.35OHM,2.5A,AR8X25,72.5TS,18X39MM,11MM,BK -,8.2MH(250KHz),10%,DR8*11,-,-,-,-,10.5OHM,-,-,-,BULK AN15VS,20MH,0.42OHM,1.5KV,20MH,22X17X34MM,220V,TR,20MH,100MOHM,-10CTO+85C ROUND,GRN,4.75mm,565nm DAR-TR,63-125%,200mW,DIP-4,ST IRFU230B,N,200V,7.5A,0.4OHM,2.5W,I-PAK IRF630B,N,200V,9A,0.4OHM,72W,TO-220 12Vdc,250mW,5A,1FormA,15mS,5mS BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 30VDC,0.3A,DPST,SELF LOCK,-,-,-,-,-,-,-,-,-,-,-,PL-3,EI 1916,310uH,-,-,7.5UH,7.5UH,DR12X15,7MM,15X15X37MM,12X9T,27TS,TR,12%,0.03OHM,USTC0.12X30 FQM15A009,AN15VS,1.95MH,SM19C,FUR3757SU,0.65 OHM,162.0,12P,-10 ~60,BK,26.0KV EER3638,AN15V,90~264V,PL-3,DMR30,EER3638,350UH AR0615(L-81),AN17L,5P,200UH,200UH,1.30 OHM,L-81,AR0630, BAR,18*13*18.5,BK 4.5OHM,+30/-20%,220V,290VAC,21A,-,TR Remarks SNA
!
SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA
SNA SNA SNA
SNA SNA
SNA SNA SNA SNA
!
!
AN15V*
7-1
7 Electrical Parts List
CONFIDENTIAL
Description THERMISTOR-NTC ASSY MICOM IC-MICROCONTROLLER S/W MICOM ASSY AUTO-MAIN CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD CORE-FERRITE BEAD C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,MLC-AXIAL C-AL C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-AL C-FILM,PEF C-FILM,MPEF C-FILM,MPEF C-AL C-FILM,MPEF C-AL C-AL C-AL C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-CERAMIC,MLC-AXIAL C-AL C-FILM,MPEF C-CERAMIC,MLC-RADIAL C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-AL C-FILM,PEF C-FILM,PEF C-AL C-AL C-AL C-FILM,PEF C-FILM,PPF C-AL 8ohm,15%,-,17mW/C,BK AN15VS 3P863,8Bit,SDIP,42P,600MIL,12MHz,ST,CMOS,PLASTIC,5V,-,-40to+85C,1040BYTE,48KBYTE AN15VS AN15VS AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),220uF,20%,16V,GP,-,6.3x11mm,2. 0.022nF,5%,50V,NP0,TP,5x3,5 0.022nF,5%,50V,NP0,TP,5x3,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 1uF,20%,50V,GP,TP,5x11,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 1uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 1uF,20%,50V,GP,TP,5x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 1nF,10%,50V,Y5P,TP,5x3.5,5 100nF,5%,100V,TP,11.5x12.5mm,5 100uF,20%,16V,GP,TP,6.3x11,5 0.1nF,5%,50V,SL,TP,5x3.5,5 4.7uF,20%,50V,GP,TP,5x11,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 150nF,5%,100V,TP,10.5x5x14.5,5 470nF,5%,63V,TP,-,5mm 47uF,20%,16V,GP,TP,5x11,5 220nF,10%,100V,TP,12.7x16,5mm 470uF,20%,16V,GP,TP,8x11.5,5 470uF,20%,16V,GP,TP,8x11.5,5 220uF,20%,35V,GP,TP,10x12.5,5 6.8nF,5%,100V,TP,5.8x12.5mm,5m 1nF,10%,50V,Y5P,TP,5x3.5,5 3.3nF,5%,100V,TP,5.8x3x12.5,5m 100nF,+80-20%,50V,Y5V,TP,2.3X3 47uF,20%,16V,GP,TP,5x11,5 100nF,5%,63V,TP,7.5x4.0x5.0mm, 820pF,5%,50V,NPO,TP,5.1x3.2x5. 10nF,5%,100V,TP,7x3.2x7mm,5mm 0.33nF,10%,50V,Y5P,TP,4x3.5,5 2.7nF,5%,100V,TP,7x3.0x6.5mm,5 150uF,20%,63V,LZ,TP,10x25,5 0.33nF,10%,500V,Y5P,TP,5.5x3,5 100uF,20%,16V,GP,TP,6.3x11,5 33nF,5%,100V,TP,5.8x12.5x3,5 22nF,5%,100V,TP,7.2x4.5x9.0mm, 3.3UF,20%,50V,BP,TP,16X25,7.5 470nF,20%,50V,GP,TP,5x11,2.5 4.7UF,20%,160V,WT,TP,8X11.5MM,5 100nF,5%,100V,TP,11.5x12.5mm,5 5.2nF,5%,630V,TP,19x7x13,7.5 1uF,20%,50V,GP,TP,5x11,5 Specification Remarks
Loc. No. TH602 CIS9 IC201 CIS BD401 BD402 BD403 BD406 BD410 BD411 BD601 BD602 BD603 BD605 C201 C202 C203 C204 C205 C206 C207 C209 C210 C211 C212 C213 C214 C215 C216 C300 C301 C302 C303 C304 C305 C306 C307 C308 C310 C315 C316 C401 C402 C403 C404 C405 C406 C407 C408 C410 C411 C412 C413 C414 C415 C416 C421 C426
Code No. 1404-001020 BH97-00330G 0903-001194 BH46-00005V BH97-00351A 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 3301-001450 2401-000010 2201-000389 2201-000389 2301-000148 2401-000603 2202-002009 2401-000603 2401-002075 2401-000603 2201-000146 2201-000017 2301-000010 2401-000025 2201-000146 2401-002075 2301-000148 2301-001049 2305-000412 2401-000031 2305-000004 2401-000037 2401-000037 2401-000849 2301-000014 2201-000017 2301-000519 2202-002009 2401-000031 2305-000665 2202-000573 2301-000148 2201-000471 2301-000203 2401-000540 2201-000469 2401-000025 2301-000005 2301-000016 2401-001012 2401-001334 2401-001222 2301-000010 2303-001029 2401-000603
SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA
7-2
AN15V*
7 Electrical Parts List
CONFIDENTIAL
Description C-FILM,MPPF C-AL C-AL C-FILM,MPPF C-FILM,MPPF C-FILM,MPEF C-FILM,MPEF C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-AL C-FILM,PEF C-AL C-FILM,PEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-FILM,PEF C-CERAMIC,MLC-AXIAL C-AL C-AL C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-AL C-AL C-AL C-AL C-FILM,PEF C-FILM,PEF C-AL C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-AL C-AL C-CERAMIC,DISC C-AL C-AL C-CERAMIC,DISC TAPE-KRAFT TAPE-PAPER TAPE-PAPER EYELET CONNECTOR-HEADER DIODE-SWITCHING Specification 150nF,5%,250V,TP,19x16x7.5,7.5 10uF,20%,50V,GP,TP,5x11,5 1uF,20%,50V,GP,TP,5x11,5 370nF,5%,250V,TP,19x18.5x12.5, 300nF,5%,250V,TP,20x18.5x10.5, 22nF,5%,250V,TP,14.5x8.8mm,7.5 10nF,5%,250V,TP,13x4.5x9mm,7.5 0.1nF,10%,500V,Y5P,TP,6.5x3,5 0.15nF,10%,2kV,Y5P,TP,6.3x5,7.5 0.82nF,10%,500V,Y5P,TP,6.5x3,5 1uF,20%,50V,BP,TP,5x11,5 10uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 10nF,5%,100V,TP,7x3.2x7mm,5mm 1uF,20%,50V,GP,TP,4x7mm,1.5mm 22nF,5%,100V,TP,7.2x4.5x9.0mm, 10uF,20%,16V,GP,TP,5x11,2.5 100nF,+80-20%,50V,Y5V,TP,8x3,5 1nF,10%,50V,Y5P,TP,5x3.5,5 220nF,20%,50V,GP,-,5x11,5 2.2uF,20%,250V,GP,TP,8x11.5,5 56nF,5%,100V,TP,9.5x12.5mm,5mm 1nF,10%,500V,Y5P,TP,7.5x3.5,5 2.2nF,5%,100V,TP,5.5X10X2.9,5m 4.7nF,20%,250VAC,Y5U,TP,16x7,7 4.7nF,20%,250VAC,Y5U,TP,16x7,7 22nF,5%,100V,TP,7.2x4.5x9.0mm, 10nF,5%,100V,TP,7x3.2x7mm,5mm 100nF,+80-20%,50V,Y5V,TP,2.3X3 33uF,20%,50V,WT,-,6.3x11mm,2.5 100uF,20%,16V,GP,TP,6.3x11,5 1uF,20%,50V,WT,TP,5x11,5 1uF,20%,50V,WT,TP,5x11,5 0.22nF,10%,1kV,Y5P,TP,6.3x5,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 1nF,10%,500V,Y5P,TP,7.5x3.5,5 2.2nF,20%,125V,Y5U,TP,11x7,5 2.2nF,20%,125V,Y5U,TP,11x7,5 1000uF,20%,16V,GP,TP,10x16,5 47uF,20%,50V,WT,TP,8x11.5,5 220uF,20%,63V,GP,TP,10x20,5 47uF,20%,50V,WT,TP,8x11.5,5 1000uF,20%,16V,GP,TP,10x16,5 1000uF,20%,16V,GP,TP,10x16,5 2.2nF,5%,100V,TP,5.5X10X2.9,5m 15nF,5%,100V,TP,7.2x4.0x7.5mm, 100uF,20%,16V,GP,TP,6.3x11,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 100nF,+80-20%,50V,Y5V,TP,2.3X3 470uF,20%,16V,GP,TP,8x11.5,5 100uF,20%,16V,WT,TP,8x11.5mm,5 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5 1uF,20%,50V,GP,TP,5x11,5 10uF,20%,50V,GP,TP,5x11,5 1nF,10%,50V,Y5P,TP,5x3.5,5 #53110,T0.1,W6,L2000M,BRN #53128,T0.15,W5.5,L2000M,BEIGE #FB-300,T0.16,W6,L2000M,R/BLU ID2.2,OD2.7,L3.1,SN,BSS3-E/EH 1WALL,3P,1R,3.96mm,STRAIGHT,SN 1N4148,100V,200mA,DO-35,TP Remarks
Loc. No. C427 C428 C429 C430 C431 C432 C433 C434 C435 C436 C440 C445 C461 C462 C463 C501 C502 C503 C504 C505 C509 C510 C513 C541 C603 C604 C605 C606 C607 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 C623 C624 C625 C626 C628 C629 C630 C631 C632 C633 C634 C643 CIS6 CIS7 CIS8 CN501 CN603 D201
Code No. 2306-000131 2401-000480 2401-000603 2301-001162 2306-000179 2305-000310 2305-001003 2201-000132 2201-000229 2201-000672 2401-001914 2401-000480 2401-002075 2301-000148 2401-000597 2301-000016 2401-000050 2201-000119 2201-000017 2401-000059 2401-002267 2301-000294 2201-000291 2301-000004 2201-000024 2201-000024 2301-000016 2301-000148 2202-002009 2401-000015 2401-000025 2401-000613 2401-000613 2201-000012 2201-000019 2201-000291 2201-000023 2201-000023 2401-000039 2401-001585 2401-000887 2401-001585 2401-000039 2401-000039 2301-000004 2301-000174 2401-000025 2201-000019 2202-002009 2401-000037 2401-000292 2201-000019 2401-000603 2401-000480 2201-000017 0203-001199 0203-001200 0203-001201 6042-000001 3711-000217 0401-000005
SNA SNA SNA SNA SNA
AN15V*
7-3
7 Electrical Parts List
CONFIDENTIAL
Description DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-ZENER DIODE-ZENER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET Specification 1N4148,100V,200mA,DO-35,TP 1N4002GP,100V,1A,DO-41,TP UF4004,400V,1A,DO-41,TP UF4004,400V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41,TP EK-04,40V,1.5A,DO-41 UF4004,400V,1A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP TVR10G,400V,1.0A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1SS244,250V,625mA,DO-34,TP 1N4148,100V,200mA,DO-35,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP UF4007,1KV,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,TP 1N4148,100V,200mA,DO-35,TP UF4007,1KV,1A,DO-41,TP UF1G,400V,1.2A,DO-204AL,TP TVR10G,400V,1.0A,DO-41,TP UZ6.2BSB,6.2V,5.99-6.24V,500mW UZ6.2BSB,6.2V,5.99-6.24V,500mW 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP 1N4148,100V,200mA,DO-35,TP ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH Remarks
Loc. No. D302 D303 D401 D402 D403 D404 D405 D407 D410 D411 D412 D413 D414 D415 D416 D420 D421 D501 D504 D505 D506 D508 D509 D510 D511 D513 D600 D602 D604 D605 D606 D607 D610 D611 D612 D615 D616 D625 D626 D627 D628 D629 D630 EY301 EY302 EY401 EY444 EY445 EY500 EY501 EY502 EY503 EY504 EY505 EY506 EY507 EY508 EY509 EY510 EY511 EY512
Code No. 0401-000005 0402-000128 0402-000274 0402-000274 0402-000006 0402-000006 0402-000208 0402-000274 0401-000005 0401-000005 0402-000546 0402-000546 0401-000005 0401-000005 0401-000005 0401-000005 0401-000004 0401-000005 0402-000546 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000012 0402-000012 0402-000546 0401-000005 0402-000012 0402-001118 0402-000546 0403-000361 0403-000361 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000001 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002 6042-000002
SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA
7-4
AN15V*
7 Electrical Parts List
CONFIDENTIAL
Description EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET EYELET PIN HINGE PIN HINGE IC-EEPROM IC-POSI.ADJUST REG. IC-POSI.FIXED REG. CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS R-METAL CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS Specification ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID2.2,OD2.7,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH ID1.5,OD2,L3.1,SN,BSS3-E/EH BRASS,D2.36!,HEAT/SINK,SN BRASS,D2.36!,HEAT/SINK,SN 524C80D41,4KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,ST 431,TO-92,3P,-,PLASTIC,2.44/2. 78DL05,TO-92,3P,4.5X4.5MM,PLASTIC,4.8/5.2V,625MW,-40TO+85C,150MA,-,TP 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 7.5Kohm,1%,1/4W,AA,TP,2.4x6.4m 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. Remarks SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA SNA
Loc. No. EY601 EY602 EY603 EY604 EY605 EY606 EY607 EY608 EY609 EY610 GT603 GT604 IC202 IC602 IC604 JP_DHHS JP101 JP102 JP11 JP110 JP113 JP118 JP119 JP129 JP130 JP135 JP137 JP142 JP143 JP144 JP146 JP147 JP148 JP158 JP160 JP162 JP163 JP171 JP175 JP176 JP179 JP180 JP183 JP184 JP186 JP187 JP193 JP194 JP195 JP196 JP197 JP198 JP199 JP2 JP20 JP200 JP201 JP202 JP204 JP205 JP206
Code No. 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000001 6042-000002 6042-000002 6042-000002 6042-000002 BH71-40300A BH71-40300A 1103-001149 1203-000002 1203-002653 BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U 2004-001211 BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U
AN15V*
7-5
7 Electrical Parts List
CONFIDENTIAL
Description CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS CBF HARNESS PCB MAIN TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL TR-SMALL SIGNAL R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON Specification 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. 52MM,AWG22(0.6PI),-,-,AWG22(0. AN15V*,FR1,1,1.6T,247*247,MAIN KSC945,NPN,250mW,TO-92,TP,120-240 KSC2383-Y,NPN,900000mW,TO-92L,TP,160-320 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSA733,PNP,250mW,TO-92,TP,120-240 KSA733,PNP,250mW,TO-92,TP,120-240 2N5551,NPN,625mW,TO-92,TP,80-250 KSP42,NPN,625mW,TO-92,-,40 KSP42,NPN,625mW,TO-92,-,40 KSA733,PNP,250mW,TO-92,TP,120-240 KSA733,PNP,250mW,TO-92,TP,120-240 2N6520,PNP,625mW,TO-92,TP,30-200 KSC945,NPN,250mW,TO-92,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KSD1616-Y,NPN,750mW,TO-92,TP,135-270 KTA1281,PNP,1000mW,TO-92L,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 KTA1281,PNP,1000mW,TO-92L,TP,120-240 KSC945,NPN,250mW,TO-92,TP,120-240 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM Remarks
Loc. No. JP207 JP208 JP209 JP21 JP210 JP211 JP212 JP213 JP214 JP215 JP216 JP217 JP219 JP220 JP221 JP25 JP3 JP30 JP32 JP33 JP34 JP35 JP36 JP37 JP4 JP43 JP56 JP57 JP58 JP60 JP62 JP64 JP8 JP9 JP91 JP94 MP1.0 Q303 Q400 Q401 Q403 Q405 Q406 Q407 Q415 Q416 Q420 Q499 Q502 Q601 Q602 Q604 Q609 Q610 Q613 Q614 R200 R201 R202 R203 R204
Code No. BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH39-40305U BH41-00217A 0501-000586 0501-000372 0501-000586 0501-000586 0501-000303 0501-000303 0501-000140 0501-000412 0501-000412 0501-000303 0501-000303 0501-000143 0501-000586 0501-000586 0501-000404 0501-002228 0501-000586 0501-002228 0501-000586 2001-000869 2001-000290 2001-000290 2001-000008 2001-000008
7-6
AN15V*
7 Electrical Parts List
CONFIDENTIAL
Description R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-CARBON(S) R-METAL R-METAL OXIDE(S) R-METAL R-METAL R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-METAL R-CARBON R-CARBON R-CARBON(S) R-METAL OXIDE(S) R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-METAL OXIDE(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-METAL R-CARBON(S) R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON(S) Specification 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 270OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 68ohm,1%,1/4W,AA,TP,2.4x6.4mm 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.5OHM,5%,1/2W,AA,TP,2.4X6.4MM 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m 1.2ohm,5%,2W,AA,TP,4x12mm 390ohm,1%,1/4W,AA,TP,2.4x6.4mm 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4m 9.1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 24KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 390KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47Kohm,1%,1/4W,AA,TP,2.4x6.4mm 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/2W,AA,TP,2.4X6.4MM 100ohm,5%,2W,AA,TP,4x12mm 12OHM,5%,1/4W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MM 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MM 1.5Kohm,5%,2W,AA,TP,4x12mm 150KOHM,5%,1/2W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM 180KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM 3.3Kohm,1%,1/4W,AA,TP,2.4x6.4m 18Kohm,1%,1/4W,AA,TP,2.4x6.4mm 680OHM,5%,1/2W,AA,TP,2.4X6.4MM 10OHM,5%,1/4W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 560ohm,5%,3W,AA,TP,6x16mm 470KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/2W,AA,TP,2.4X6.4MM Remarks
Loc. No. R205 R206 R207 R208 R209 R212 R213 R214 R215 R216 R217 R218 R219 R220 R221 R222 R223 R224 R225 R229 R235 R236 R300 R301 R302 R307 R308 R309 R310 R311 R312 R313 R314 R316 R317 R327 R328 R401 R404 R405 R406 R407 R408 R411 R412 R413 R414 R415 R416 R417 R418 R419 R420 R423 R424 R425 R426 R427 R428 R429 R430
Code No. 2001-000290 2001-000435 2001-000869 2001-000869 2001-000290 2001-000591 2001-000290 2001-000429 2001-000281 2001-000281 2001-000281 2001-000281 2001-000290 2001-000281 2001-000734 2001-000734 2001-000554 2001-000869 2001-000869 2001-000281 2001-000290 2001-000290 2004-001202 2001-000734 2001-000281 2001-000908 2001-001053 2004-001022 2003-000422 2004-000853 2004-000498 2001-001015 2001-000539 2001-000812 2001-000786 2001-000689 2001-000356 2004-000979 2004-001022 2001-000449 2001-000522 2001-001099 2003-000455 2001-000333 2001-000429 2001-001048 2001-001048 2003-000429 2001-000107 2001-000290 2001-000613 2001-000397 2001-000354 2004-000698 2004-000412 2001-001178 2001-000110 2001-000429 2003-000736 2001-000773 2001-001078
! !
AN15V*
7-7
7 Electrical Parts List
CONFIDENTIAL
Description R-METAL OXIDE(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON(S) R-CARBON(S) R-METAL R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-METAL R-METAL R-METAL R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-METAL R-CARBON R-METAL R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL OXIDE(S) R-CARBON R-COMPOSITION R-COMPOSITION R-CARBON R-METAL OXIDE(S) R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-METAL R-METAL R-CARBON Specification 1.5ohm,5%,3W,AA,TP,6x16mm 22OHM,5%,1/2W,AA,TP,2.4X6.4MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 68OHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12mm 10OHM,5%,1/2W,AA,TP,2.4X6.4MM 68OHM,5%,1/2W,AA,TP,2.4X6.4MM 120Kohm,1%,1/4W,AA,TP,2.4x6.4m 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12mm 68KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 39Kohm,1%,1/4W,AA,TP,2.4x6.4mm 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2Kohm,1%,1/4W,AA,TP,2.4x6.4m 12Kohm,1%,1/4W,AA,TP,2.4x6.4mm 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7OHM,5%,1/4W,AA,TP,2.4X6.4MM 12KOHM,5%,1/2W,AA,TP,2.4X6.4MM 22KOHM,5%,1/2W,AA,TP,2.4X6.4MM 27KOHM,5%,1/2W,AA,TP,2.4X6.4MM 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 130KOHM,5%,1/8W,AA,TP,1.8X3.2MM 36Kohm,1%,1/4W,AB,TP,2.4x6.4mm 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100Kohm,1%,1/4W,AA,TP,2.4x6.4m 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,2.4X6.4MM 47OHM,5%,1/4W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10Kohm,5%,3W,AA,TP,6x16mm 220OHM,5%,1/4W,AA,TP,2.4X6.4MM 180Kohm,5%,1/2W,AA,TP,3.9x9mm 180Kohm,5%,1/2W,AA,TP,3.9x9mm 6.8OHM,5%,1/4W,AA,TP,2.4X6.4MM 56Kohm,5%,2W,AA,TP,4x12mm 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220ohm,5%,1/2W,AA,TP,2.4x6.4mm 1KOHM,5%,1/2W,AA,TP,2.4X6.4MM 2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1OHM,5%,1/4W,AA,TP,2.4X6.4MM 91Kohm,1%,1/4W,AA,TP,2.4x6.4mm 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.4Kohm,1%,1/4W,AA