chassis 4bsc.pdf part of sharp 66AS05h chassis 4bsc.rar, chasis 4bsc of sharp tv text manual preview

Text preview for : chassis 4bsc.pdf part of sharp 66AS05h chasis 4bsc of sharp tv

Back to : chassis 4bsc.rar | Home

SHARP 66AS-05H
General Information 4BS-C Chassis Matrix
Item See Model Book
5 Remote Control Unit ......................................................................... Sharp 66AS-06H

1
Service Adjustments
Important Service Notes Maintenance and repair of this receiver should be done by qualified personnel only. Servicing of High Voltage System and Picture Tube When servicing the high voltage system, remove static charge from it by connecting a 10 k W Resistor in series with an insulated wire (such as a test probe) between picture tube ground tag and high voltage lead. (AC line cord should be disconnected from AC outlet.) 1: Picture tube in this receiver employs integral implosion protection. 2: Replace with tube of the same type number for continued safety. 3: Do not lift picture tube by the neck. 4: Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage completely. X-Ray This receiver is designed so that any X-Ray radiation is kept to an absolute minimum. Since certain malfunctions or servicing may produce potentially hazardous radiation with prolonged exposure at close range, the following precautions should be observed: 1: When repairing the circuit, be sure not to increase the high voltage to more than 30.0 kv, (at beam 1000µA) for the set. 2: To keep the set in a normal operation, be sure to make it function on 25.7 kv ± 1.5 kv (at beam 1300 µA) in the case of the set. The set has been factory -- Adjusted to the abovementioned high voltage. If there is a possibility that the high voltage fluctuates as a result of the repairs, never forget to check for such high voltage after the work. 3: Do not substitute a picture tube with unauthorised types and/or brands which may cause excess X-ray radiation. Before Returning The Receiver Before returning the receiver to the user, perform the following safety checks. 1: Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver. 2: Inspect all protective devices such as nonmetallic control knobs, insulating fish papers, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators etc. PIF/SIF/AGC/G2 Adjustment 1: Trap adjustment Adjusting Point T1201: Trap Coil (Adj.-P Trap) T1200:Trap Coil (Adj.-S Trap) 1: Connect sweep generator output to IF in (FA (1)). 2: Connect response cable with detector to collector line of Q1200 (See fig.1) Trap) so that traps are (41.5 MHz) and (32.0 MHz). (See fig. 2) -- ALTER NVM POS. -- ALTER NVM VAL. -- AUTO INSTALLATION To exit service mode, press main switch to off. Adjustment Note: The procedure for making adjustments to Vertical Corrections is as follows: -- Adjust S-CORRECTION -- Adjust VERT. SHIFT -- Adjust VERT. AMPLITUDE Fig. 2 Geometry Adjustment Procedure 2: VCO Adjustment Adjusting Point T1202: VCO Adjust Coil 1: Feed the following signal to pin (1) of connector (FA) in IF unit. Frequency: 39.5 MHz (CW) ± 5 kHz Level approx. 85 dB 2: Adjust T1202 so that voltage at pin (7) (AFT output) of connector (FA) in IF unit is 2.5 ± 0.2v. 3: RF AGC Adjustment Adjusting Point R1216: RF AGC Control 1: Receive "COLOUR BAR" signal. 2: Connect DC voltmeter to Test Point TP1200 (RF AGC). 3: Set AGC control (R1216) to maximum position (memory). 4: Adjust R1216 to obtain voltage of 0.1v below maximum voltage (step 3). 4: G2 Adjustment 1: Receive "MONOSCOPE PATTERN" signal. 2: Connect DC voltmeter with Test probe attenuator ( 1000) to HH1 Test point on PWB-C. 3: Adjust G2 to obtain 730v on HH1. Service Mode Function This mode function is provided to assist with the settings of those adjustments that may vary from one Picture Tube to another, or between models. In order to use the Service Mode 1: Connect Test Pattern signal to antenna terminal. 2: Press main switch to off. 3: Press w and CHv buttons and main switch to on simultaneously. 4. Service mode is now entered. The required adjustments can then be made from the Remote Control Unit. The only buttons required are the following: v CH w for movement in adjustment options menu; v w are used to carry out an adjustment in said menu; ON/OFF is used to memorise a new adjustment. Adjustment menu is as follows: -- SERVICE SOFTWARE -- CROMA-LUNA DELAY -- VERT. SHIFT -- HOR. SHIFT -- E-W WIDTH -- E-W PALABOLA -- E-W CORNER -- E-W TRAPEZOID -- VERT. SLOPE -- VERT. AMPLITUDE -- S-CORRECTION -- RED REFERENCE -- GREEN REFERENCE -- BLUE REFERENCE Chroma-Luma Delay a: Receive Philips pattern signal. b: When volume-up button is pressed, luma phase delays. c: When volume-down button is pressed, chroma phase delays. d: Adjust the Chroma-Luma delay. Vert. Shift a: Receive Philips pattern signal. b: When volume-down button is pressed, picture moves up. c: When volume-up button is pressed, picture moves down. d: Adjust the Vertical location to obtain picture centring (fig. 3). Hor. Shift a: Receive Philips pattern signal. b: When volume-up button is pressed, picture moves to the left. c: When volume-down button is pressed, picture moves to the right. d: Adjust the horizontal location to obtain picture centring (fig. 4). E-W Width a: Receive Philips pattern signal. b: When volume-up button is pressed, horizontal scanning increases. c: When volume-down button is pressed, horizontal scanning decreases. d: Adjust the horizontal amplitude to obtain 9% overscan (fig. 5). E-W Parabola a: Receive Philips pattern signal. b: When volume-up button is pressed, slide pincushion changes from pincushion to barrel shape. c: When volume-down button is pressed, slide pincushion changes from barrel to pincushion shape. d: Adjust the E-W PARABOLA to obtain condition as in fig. 6. E-W Corner a: Receive Philips pattern signal. b: When volume-down button is pressed, slide pincushion changes from pincushion to barrel shape. c: When volume-up button is pressed, slide pincushion changes from barrel to pincushion shape. d: Adjust the E-W CORNER to obtain condition as in fig. 7. E-W Trapezoid a: Receive Philips pattern signal. b: When volume-up button is pressed, slide pincushion changes. c: When volume-down button is pressed, slide pincushion changes. d: Adjust the E-W TRAPEZOID to obtain condition as in fig. 8. Vert. Amplitude a: Receive Philips pattern signal. b: When volume-up button is pressed, vertical size of picture increases. c: When volume-down button is pressed, vertical size of picture decreases. d: Adjust the vertical size to obtain overscan as in fig. 9. S-Correction a: Receive Philips pattern signal. b: When volume-up button is pressed, upper and lower scanning decreases, and centre scanning increases. c: When volume-down button is pressed, upper and lower scanning increases and centre scanning decreases. d: Adjust the S-correction to obtain a balance between upper, lower and centre (fig. 10). The following adjustments are only required when the Picture Tube is changed. Red Reference/Green Reference/Blue Reference a: Adjust G2. b: Tune in white card. c: Adjust colour to minimum. d: Position colourmeter in centre of screen. e: Using brightness and contrast buttons, select a luminance of 120 NITS. f: Operate again in Service Mode and select location RED REFERENCE/GREEN REFERENCE/BLUE REFERENCE to obtain colour co-ordinates: X = 0.290 ± 0.0015 Y= 0.284 ± 0.015 g: Exit Service Mode and check colour coordinates `X' and `Y' at 20 and 120-NITS. It may be necessary to repeat procedure. Note: Locations: RED REFERENCE alter `X' co-ordinate; GREEN REFERENCE alter the `Y' co-ordinates; BLUE REFERENCE alter the `X' and `Y' co-ordinates. Alter NVM POS XX---> Storage location XX---> Assigned value When w Location. v buttons are pressed, alter Storage

Recommended Safety Parts
Item
V1 L1702

Part No.

Description
CRT 71 cm (28 inch) with Deflection Yoke Purity Magnet and Wedges Degaussing (ADG) Coil CRT Spring Tuner, UHF Regulating Pulse Width Modulator Photo Coupler 2SD1546 2SC2412 2SA1037 BY228 Tel: ++385-31-856-637 Zener Diode, 4.7V Zener Diode, 20V Tel/fax: ++385-31-856-139 1N4148 Mob: 098-788-319 1N4935 1N4148 Zener Diode 1N4148 1N4005 DAN202K Coil, 3.3µH Coil, 1µH FlybackTrans. (F.B.T) Switching ModeTrans. 330 385V Electrolytic 330 25V Electrolytic 0.01 63V Mylar 2200p 63V Mylar 330p 2kV Ceramic 0.1 63V Mylar 1000p 63V Mylar 1000p 500V Ceramic 0.1 63V Mylar 4700p 1.6kV Polypro Film 100 50V Electrolytic 4.7 50V Electrolytic 100 6.3V Electrolytic 3300p 4kV Ceramic 10 1/2W Fuse Resistor 4.7 1/2W Fuse Resistor 10 1/3W Fuse Resistor 10 1/2W Fuse Resistor 10 1/3W Fuse Resistor 1 1/2W Fuse Resistor 2.2 1/2W Fuse Resistor 1 1/2W Fuse Resistor 39 1/2W Fuse Resistor 1 1/2W Fuse Resistor 12k 1/10W Metal Oxide 5.6k 1/8W Carbon 470k 1/4W Carbon 3.9k 1/10W Metal Oxide 270 1/2W Carbon 1k 1/2W Carbon 100k 2W Metal Oxide 47k 2W Metal Oxide 12 2W Metal Oxide 1k 1/8W Carbon 0.56 2W Metal Film 100 1/10W Metal Oxide 4.7k 1/10W Metal Oxide 22k 1/10W Metal Oxide 27k 1/2W Carbon 10k 1/10W Metal Oxide 1k 1/10W Metal Oxide 100 1/2W Carbon 0.56 2W Metal Film 8.2M 1/2W Solid 4.7 1/3W Fuse Resistor 10 1/3W Fuse Resistor IC Protector IC Protector Ferrite Bead Plug, 3-pin (B) 220 1/2W Fuse Resistor 10 1/2W Fuse Resistor CRT Socket DX0240CE Varistor Positive Coefficient Themistor Line Filter 0.1 AC300V Mylar 0.01 AC250V Ceramic 0.01 AC250V Ceramic 4.7 15W Cement Fuse,T2AH Plug, 3-pin (A) Plug, 2-pin (G) Plug, 3-pin (B) Main Power 22 1/3W Fuse Resistor AC Cord Assy

VB66EAK7111*N CCiLG0304WEV1 MSPRT0001CEFJ TU200 VTUATEKB7-022 IC700 RH-iX1487BMZZ IC701,702 RH-FX0101BMZZ Q700 VS2SD1546//2E Q701 VS2SC2412KQ-1 Q702 VS2SA1037KQ-1 D701 RH-DX0299BMZZ D703 RH-EX0478BMZZ D704 RH-EX0423BMZZ D705 RH-DX0045BMZZ D706 RH-DX0511BMZZ D707 RH-DX0045BMZZ D708 RH-EX0477BMZZ D709 RH-DX0045BMZZ D712 RH-DX0502BMZZ D713 VHDDAN202K/-1 L700 VP-CF3R3K0000 L701 VP-CF1R0M0000 T600 RTRNF2021 BMZZ T700 RTRNZ0519BMZZ C702 RC-EZ0109BMZZ C703 VCEAGA1EW337M C704 RC-FZ9103BMNJ C705 RC-FZ9222BMNJ C706 RC-KZ0036CEZZ C707 RC-FZ9104BMNJ C708 RC-FZ9102BMNJ C709 VCKYPA2HB102K C710 RC-FZ9104BMNJ C711 VCFPPD3CA472H C712 VCEAGA1HW107M C714 VCEAGA1HW475M C715 VCEAGA0JW107M C749 RC-KZ0156CEZZ R200,R202 RR-XZ0212BMZZ R310,R311 RR-XZ0208BMZZ R363 RR-XZ0112BMZZ R413 RR-XZ0212BMZZ R475 RR-XZ0112BMZZ R503 RR-XZ0200BMZZ R611 RR-XZ0204BMZZ R615 RR-XZ0200BMZZ R620 RR-XZ0219BMZZ R626,R631 RR-XZ0200BMZZ R701 VRS-TV1JD123J R702 VRD-RA2BE562J R705 VRD-RA2EE474J R706 VRS-TV1JD392J R707 VRD-RA2HD271J R708 VRD-RA2HD102J R710 VRS-VV3DB104J R711 VRS-VV3DB473J R712 VRS-VV3DB120J R714 VRD-RA2BE102J R715 VRN-VV3DBR56J R716 VRS-TV1JD101J R718,R719 VRS-TV1JD472J R720 VRS-TV1JD223J R721 VRD-RA2HD273J R722 VRS-TV1JD103J R723 VRS-TV1JD102J R724 VRD-RA2HD101J R725 VRN-VV3DBR56J R729,R730 VRC-UA2HG825K R801 RR-XZ0108BMZZ R806,R839,R844 RR-XZ0112BMZZ F751 QFS-J2521GEZZ F753 QFS-J4021GEZZ FB700,FB751,FB752 RBLN-0037CEZZ P700 QPLGN0304CEZZ R1872 VRG-RL2HB221J R1873 RR-XZ0017CEZZ Z1801 QSOCV0919CEZZ D1700,D1701,D1702,D1703 RH-DX0240CEZZ VA1700 RH-VX0033CEZZ PR1700 RMPTP0028CEZZ L1700 RCiLF0108BMZZ C1700 RC-FZ0145BMZZ C1701,C1703,C1704 RC-KZ0029CEZZ C1705,C1706 RC-KZ0029CEZZ R1700 VRW-KQ41C4R7K F1700 QFS-C2050BMZZ P1700 QPLGN0304CEZZ P1701 QPLGN0207CEZZ P1702 QPLGN0304CEZZ S1700 QSW-P0566CEZZ R3439,R3461 RR-XZ0116BMZZ ACC701 CACCB5002BMV0

RTV servis Horvat
www.rtv-horvat-dj.hr

Alter NVM VAL XX---> Storage location XX---> Assigned value When w v buttons are pressed, alter Assigned Value.

Fig. 3

Fig. 7

Fig. 4

Fig 8

Fig. 5

Fig. 9

Fig. 1 3: Adjust T1200 (Adj.-S Trap) and T1201 (Adj.-P

Fig. 6

Fig.10

Safety Parts / Service Adjustments / Nicam Diagram / Scart Diagram / Text Diagram / IF Diagram / CRT Control Diagram / CRT Socket Diagram / Main Diagram

SHARP 66AS-05H
NICAM Diagram

2
Scart Diagram

Safety Parts / Service Adjustments / Nicam Diagram / Scart Diagram / Text Diagram / IF Diagram / CRT Control Diagram / CRT Socket Diagram / Main Diagram

SHARP 66AS-05H
IF Diagram

3
CRT Control Diagram

CRT Socket Diagram

Text Diagram
Safety Parts / Service Adjustments / Nicam Diagram / Scart Diagram / Text Diagram / IF Diagram / CRT Control Diagram / CRT Socket Diagram / Main Diagram

SHARP 66AS-05H
Main Diagram

4

RTV servis Horvat
Tel: ++385-31-856-637 Tel/fax: ++385-31-856-139 Mob: 098-788-319

www.rtv-horvat-dj.hr

Safety Parts / Service Adjustments / Nicam Diagram / Scart Diagram / Text Diagram / IF Diagram / CRT Control Diagram / CRT Socket Diagram / Main Diagram