Text preview for : 08-rh-9-disass.pdf part of Nokia 3510i, 3530 Service Manual, Part, Variant, Tools, Troubleshooting, Schematic, ecc. - File 11
Back to : gsm_RH-9_.part1.rar | Home
Customer Care Solutions RH-9 Series Transceivers
Disassembly Instructions
Issue 1 11/02
ăNokia Corporation.
RH-9 Disassembly Instructions Table of Contents
Company confidential CCS Technical Documentation
Page No Disassembly Procedure .................................................................................................. 3 Remove Shielding Lids .................................................................................................. 6 Reassembly procedure ................................................................................................... 7
Page 2
ăNokia Corporation.
Issue 1 11/02
CCS Technical Documentation
Company confidential RH-9 Disassembly Instructions
Disassembly Procedure
Table 1:
1. Release the A-cover from the bottom side of the unit.
2. Take away the A-cover.
3.Also protect the inner part of the window
4. Open the six screws in the predefined order-
with a foil. The keymat is loose inside the A- with a Torx 6 driver. When re-assembling the reverse order has to be taken with a torque cover. of 28Ncm.
5. When releasing the side clips of the D-cover you can use the SRT 6.
6. This
is the second clip.
7. Take away the Display Assembly (UI module)
8. There are two snaps on each side of the metal
and avoid touching the pads.
frame.
Issue 1 11/02
ăNokia Corporation.
Page 3
RH-9 Disassembly Instructions
Company confidential CCS Technical Documentation
Table 2:
9. Remove the metal frame.
10. If you hold the UI module upside down,
the speaker drops out of its hollow.
11. The next step is to take out the RadioModule EY1A. Take care of LEDs.1
12. Lift up the Battery Connector with your
fingers. You can use the SRT-6 opening tool.
13. Remove the power key.
14. To loosen the System Connector you can
use the SRT-6 opening tool. Take care not to scratch D-cover or connector housing.
15. The Microphone can be changed sepa-
16. When re-assembling the Microphone
rately. To remove it from connector housing , you have to push it with for example Torx Driver.
remember the right direction. The hole of the Microphone has to point to the hole of the connector housing.
Page 4
ăNokia Corporation.
Issue 1 11/02
CCS Technical Documentation
Company confidential RH-9 Disassembly Instructions
Table 2:
17. The SALT speaker is taped to the D-cover and can be removed with a straight bladedscrewdriver.
18. If you need to change the VIBRA motorstrong tweezers or pliers can be taken.
19. Remove the SIM card support this way.
20. The Release Spring is locked on two sides. Use a screwdriver to unlock the two snaps
21. After releasing the two hooks, you can remove the Release Springs easily.
Issue 1 11/02
ăNokia Corporation.
Page 5
RH-9 Disassembly Instructions
Company confidential CCS Technical Documentation
Remove Shielding Lids
Table 3:
23. When working with PWB, always use repair Jig.
22. Remove Shielding Lids. Do not reuse shielding lid once it is removed.
Page 6
ăNokia Corporation.
Issue 1 11/02
CCS Technical Documentation
Company confidential RH-9 Disassembly Instructions
Reassembly procedure
Reassembly takes place in reversed order compared with disassembly.
Issue 1 11/02
ăNokia Corporation.
Page 7
RH-9 Disassembly Instructions
Company confidential CCS Technical Documentation
[This page left intentionally blank]
Page 8
ăNokia Corporation.
Issue 1 11/02