Text preview for : SATELLITE PRO TE2000.pdf part of Toshiba Satellite TE2000 Field Replaceable Unit Documentation, General Information - (5.072Kb) Part 1/3 - pag. 11
Back to : laptop_©_.part1.rar | Home
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
TM
GENERAL INFORMATION
Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 0&1) 2. Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mat 7. Tweezers
Before attempting any of the following procedures, make sure that the main battery and AC adaptor is not connected to the unit and the environment in which you are working on is protected from Electro-Static Discharge(ESD).
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
TM
TABLE OF CONTENTS:
1. BATTERY PACK REMOVAL 2. OPTIONAL PC CARD REMOVAL 3. SELECT BAY REMOVAL 4. CD-R/DVD-ROM DRIVE DISASSEMBLY 5. MEMORY MODULE REMOVAL 6. MODEM BOARD REMOVAL 7. HDD REMOVAL 8. KEYBOARD REMOVAL 9. WIRELESS LAN CARD REMOVAL 10. TOP COVER REMOVAL 11. COOLING MODULE REMOVAL 12. CPU REMOVAL 13. RTC BATTERY REMOVAL 14. POWER SUPPLY BOARD REMOVAL 15. SOUND BOARD REMOVAL 16. SYSTEM BOARD REMOVAL 17. MEMBRANE SWITCH REMOVAL 18. SPEAKERS REMOVAL 19. 14.1'' DISPLAY MASK REMOVAL 20. FL INVERTER AND 14.1'' LCD REMOVAL
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
BATTERY PACK REMOVAL
Battery Lock Release lever Battery Pack PC card Eject button 1. Turn the computer upside down as shown. 2. Slide the battery lock to unlock position. 3. Slide battery release lever in the direction of the arrow. 3. Lift out the battery. 1. Press the eject button of the PCCard you want to remove. 2. Press the extended eject button to pop the PC card out. 3. Grasp the PC card and remove it. Note: Before removing any PC Card device, make sure it is "STOPPED" in the PC Card manager.
TM
OPTIONAL PC CARD REMOVAL
SELECT BAY REMOVAL
CD-R/DVD-ROM DRIVE DISASSEMBLY
CD-R/DVD-ROM drive Base cover
Connector Release lever Select bay device
M2x3 silver flat head screws
1. Turn the computer upside down. 2. Slide the release lever in the direction of the arrow. 3. Pull out the select bay device in the direction of the arrow.
M2x8 silver Connector cover screws 1. Remove five M2x3 silver flat head screws securing the base cover and lift out the cover. 2. Remove two M2x8 silver screws securing the connector cover. 3. Remove the connector cover and the connector from the CD-R/DVD-ROM drive.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
MEMORY MODULE REMOVAL
Memory slot cover
TM
M2.5x4 black screws
1. Turn the computer upside down. 2. Remove two M2.5x4 black screws securing the memory cover. 3. Lift out the memory slot cover.
Memory clips 4. Spread the memory clips outward and pull the memory module out of the connector on a 45 degree angle.
MODEM BOARD REMOVAL
M2x4 silver screws Modem harness Modem slot cover
M2.5x4 black screw 1. Remove one M2.5x4 black screw securing the modem slot cover. 2. Insert your finger nail or the case separator into the notched side of the cover and lift up to release the two latches securing the left side of the modem slot cover.
Modem board 3. Disconnect the modem harness from the modem board. 4. Remove two M2x4 silver screws securing the modem board. 5. Lift up the modem board to disconnect it from the system board.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
HDD REMOVAL
TM
HDD cover
M2.5x6 black screw
Plastic Tab
HDD pack
1. Turn the computer upside down. 2. Remove one M2.5x6 black screw securing HDD cover. 3. Remove the HDD cover.
4. Unfold the plastic tab and pull to remove the HDD from the bay.
HDD REMOVAL
HDD bracket
KEYBOARD REMOVAL
HDD
M3x4 brass flat head screws M2.5x12 black screws 1. Turn the computer upside down. 2. Remove two M2.5x12 black screws securing the keyboard holder.
5. Remove two M3x4 brass flat head screws securing the HDD to the bracket and remove the HDDbracket.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
KEYBOARD REMOVAL
Latch
TM
Keyboard Keyboard lock
Keyboard holder 1. Turn the computer right side up and open the display panel. 2. Using the case separator, unlatch the keyboard holder at the top of the keyboard.
M2.5x2.6 black screws 3. Remove one M2.5x2.6 black screws securing the keyboard. 4. Slide the keyboard lock upward to release the keyboard.
KEYBOARD REMOVAL
Keyboard
WIRELESS LAN CARD REMOVAL
Keyboard cable
PJ445
Mini PCI cover 5. Lift out the keyboard and set it as shown above. 6. Disconnect the keyboard cable from PJ445 on the system board.
M2.5x4 security torx screw
1. Remove one M2x4 security torx screw securing the mini PCI cover and lift out the cover.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
WIRELESS LAN CARD REMOVAL
TM
TOP COVER REMOVAL
M2.5x6 silver screws M2.5x4 black flat head screw
Mini-PCI connector clips Wireless LAN card
M2.5x12 black screws White coax cable Black coax cable M2.5x20 black screws 1. Turn the computer upside down and remove the following screws: -9 M2.5x6 black screws -1 M2.5x4 black flat head screw -2 M2.5x20 and 1 M2.5x12 black screws Rubber seals 2. Disconnect the black and white coax from the wireless LAN card. 3. Spread the Mini-PCI connector clips and pull the Wireless LAN card out of the connector about 45 degree angle.
TOP COVER REMOVAL
M2.5x4 silver screws 2. Turn the computer right side up with the rear facing you. 3. Remove two M2.5x4 silver screws securing the top cover. 4. Open the display panel. Mask seals 5. Remove two mask seals and four rubber seals on the display mask using a pair of fine-tipped tweezers. 6. Remove two M2.5x6 black screws and four M2x6 silver flat head screws securing the display mask. 7. There are 23 latches securing the display mask. Carefully insert your fingers between the mask and the LCD panel and pry open the latches starting from the six top latches, to the five latches on each right and left sides, ending with the bottom seven latches.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
TOP COVER REMOVAL
Cooling module M2.5x6 black screw Right speaker cable Left speaker cable PJ311 PJ310 LCD/FL harness PJ34 3. Disconnect the left speaker cable from PJ310 and the right speaker cable from PJ311 on the top board. 4. Disconnect the LCD/FL harness from PJ34 and the IPS membrane switch fromPJ309 on the system board. 5. Remove one M2.5x6 black screw securing the top cover. 6. Lift out the top cover assembly.
TM
COOLING MODULE REMOVAL
M2.5x6 black screws
Fan cable
M2X4 brass screws PJ770 1. Disconnect the fan cable from PJ770 on the top board. 2. Remove four M2x4 brass screws and two M2.5x6 black screws securing the cooling module. 3. Lift out the cooling module.
CPU REMOVAL
CPU
RTC BATTERY REMOVAL
Close CPU lock Open
Silicone grease 1. Insert a flat head screwdriver in the CPU lock and rotate it counter-clockwise to unlock the CPU. 2. Lift out the CPU. NOTE: When installing the CPU, make sure that a silicone grease is applied before attaching the heat sink. Please refer to FSB-200112 for the complete procedures on how to apply the silicone grease.
RTC Battery PJ5 RTC harness 1. Disconnect the RTC harness from PJ5 on the Battery/LED board. 2. Lift out the RTC battery.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
POWER SUPPLY BOARD REMOVAL
System board PJ150 Wireless LAN switch button Sound Interface cable PJ103
TM
SOUND BOARD REMOVAL
Power supply harness
M2.5x4 black flat head screws 1. Disconnect the power supply harness from PJ850 and PJ851 on the system board. 2. Remove one M2.5x4 black flat head screws securing the power supply board. 3. Disconnect the power supply board from the system board.
Power supply board
SYSTEM BOARD REMOVAL
M2.5x4 black flat head screw SD/Sound board 1. Disconnect the sound interface cable from PJ103 and the SD interface cable from PJ150 on the SD/Sound board. 2. Remove one M2.5x4 black flat head screw securing the SD/Sound board. 3. Remove the wireless LAN switch button. 4. Lift out the SD/Sound board. PJ803
HDD guide assy Select bay cover SD interface cable Sound interface cable M2.5x4 black flat head screws
M2.5x6 black flat head screws 1. Remove one M2.5x6 black flat head screw securing the HDD guide assembly and lift out the HDD guide assembly. 2. Remove three M2.5x6 black flat head screws securing the select bay cover and lift out the select bay cover.
DC-IN jack harness
3. Disconnect the following cables from the system board: -Sound interface cable from PJ103 -SD interface cable from PJ150 -DC-IN jack harness from PJ803 4. Remove three M2.5x4 black flat head screws securing the system board. 5. Lift out the system board.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
MEMBRANE SWITCH REMOVAL
TM
SPEAKERS REMOVAL
Membrane switch assy
Left and right speakers
M2.5x4 black flat head screws 1. Remove three M2.5x4 black flat head screws securing the membrane switch. 2. Lift out the membrane switch assembly.
M2.5x4 black flat head screws 1. Turn the computer right side up and open the LCD panel. 2. Disconnect the left speaker cable from PJ310 and right speaker cable from PJ311 on the system board. 3. Remove two M2.5x4 black flat head screws securing the left and right speakers. 4. Lift out the speakers.
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite TE2000
14.1" DISPLAY MASK REMOVAL
Rubber seals
TM
FL INVERTER AND 14.1" LCD REMOVAL
M2x5 silver screws
LCD module assy
M2x3 silver screws
M2x3 silver screws
Mask seals
1. Remove two mask seals and four rubber seals on the display mask using a pair of fine-tipped tweezers. 2. Remove two M2.5x6 black screws and four M2x5 silver flat head screws securing the display mask. 3. There are 20 latches securing the display mask. Carefully insert your fingers between the mask and the LCD panel and pry open the latches starting from the six top latches, to the five latches on each right and left sides, ending with the bottom seven latches.
LCD/ FL harness
FL inverter board
M2x4 silver screw
FL cable
1. Remove one M2x5 silver screw securing the FL inverter board. 2. Carefully lift up the FL inverter board and disconnect the LCD/FL cable from CN1 and the FL cable from CN2. 3. Remove two M2x5 silver screws securing the LCD bracket. 4. Remove four M2X3 silver screws securing the LCD module. 5. Carefully rotate out the top of the LCD module enough to access the display cable 6. Disconnect the LCD/FL cable from the LCD module. 7. Lift out the LCD module and peel off two EMI shield/cushion.
Tough Enough for Today's World.
TOSHIBA