Text preview for : service manual_monitor_LG_F900.pdf part of LG F900B Service Manual Color Monitor factory Model F900BJ - (5.995Kb) Part 1/3 - pag. 35
Back to : 19inch_crt_monitor_©_.par | Home
Website:http://biz.LGservice.com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : CA-130
FACTORY MODEL: F900BJ
MODEL: F900B (F900BJ-AL**E)
( ) **Same model for Service
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
SPECIFICATIONS ................................................... 2 DESCRIPTION OF BLOCK DIAGRAM................... 11
SAFETY PRECAUTIONS ........................................ 3 ADJUSTMENT ...................................................... 13
TIMING CHART ....................................................... 4 TROUBLESHOOTING GUIDE .............................. 15
OPERATING INSTRUCTIONS ................................ 5 EXPLODED VIEW.................................................. 21
CONTROL LOCATIONS ......................................... 7 REPLACEMENT PARTS LIST .............................. 23
WIRING DIAGRAM ................................................. 8 PIN CONFIGURATION .......................................... 30
DISASSEMBLY ....................................................... 9 SCHEMATIC DIAGRAM ......................................... 33
BLOCK DIAGRAM ................................................. 10 PRINTED CIRCUIT BOARD................................... 35
SPECIFICATIONS
1. PICTURE TUBE 3-2. Power Consumption
Size : 19 inch (Flat Slot Mask)
MODE POWER CONSUMPTION LED COLOR
DefIection Angle : 90°
MAX Yes less than 120W (140W) GREEN
Neck Diameter : 29.1 mm
Strip Pitch : 0.24 mm STAND-BY No less than 8W (30W) AMBER
Diagonal Size : 457.5 mm SUSPEND No less than 8W (30W) AMBER
View Size : 366.0 x 274.5 mm -
POWER SWITCH OFF - less than 1W (20W)
Face Treatment : AR-ASC (Anti-Reflective and
Anti-Static Coating)
4. DISPLAY AREA
2. SIGNAL 4-1. Active Video Area :
2-1. Horizontal & Vertical Sync · Max Image Size - 366.0 x 274.5mm (14.40" x 10.80")
1) Input Voltage Level : Low= 0.8V, High= 2.1V · Preset Image Size - 350 x 262 mm (13.78" x 10.31")
2) Sync Polarity : Positive or Negative
4-2. Display Color : Full Colors
2-2. Video Input Signal 4-3. Display Resolution : 1600 Dots x 1200Lines/75Hz
1) Voltage Level : 0 ~ 0.7 Vp-p 4-4. Video Bandwidth : 203MHz
a) Color 0, 0 : 0 Vp-p
b) Color 7, 0 : 0.467 Vp-p 5. ENVIRONMENT
c) Color 15, 0 : 0.7 Vp-p 5-1. Operating Temperature: 0°C ~ 40°C (32°F ~ 103°F)
2) Input Impedance : 75 (Ambient)
3) Video Color : R, G, B Analog 5-2. Relative Humidity : 10% ~ 90%
4) Signal Format : Refer to the Timing Chart (Non-condensing)
5-3. Altitude : 10,000 ft
2-3. Signal Connector
15 Pin D-Sub Connector 6. DIMENSIONS (with TILT/SWIVEL)
Width : 466.6 mm (18.37")
2-4. Scanning Frequency Depth : 472.5 mm (18.60")
Horizontal : 30 ~ 98 kHz Height : 474 mm (18.66")
Vertical : 50 ~ 160 Hz
7. WEIGHT (with TILT/SWIVEL)
3. POWER SUPPLY Net Weight : 23.2 kg (51.82 lbs)
3-1. Power Range Gross Weight : 26.6 kg (59.52 lbs)
AC 100~240V, 50/60HZ, 2.5A Max
AC 200~240V, 50Hz, 1.5A Max.(PFC version) 8. USB Specifications
USB Standard : Rev. 1.0 complied self-powered hub
Downstream power supply : 500mA for each (MAX)
Communication speed : 12 Mbps (Full), 1.5 Mbps (Low)
USB port : 1 Upstream port
2 Downstream ports
-2-
SAFETY PRECAUTIONS
SAFETY-RELATED COMPONENT WARNING! X-RADIATION
There are special components used in this color monitor The only potential source of X-radiation is the picture tube.
which are important for safety. These parts are marked However, when the high voltage circuitry is operating
on the schematic diagram and the replacement properly there is no possibility of an X-radiation problem.
parts list. It is essential that these critical parts should be The basic precaution which must be exercised is keep the
replaced with the manufacturer's specified parts to high voltage at the factory recommended level; the normal
prevent X-radiation, shock, fire, or other hazards. Do not high voltage is about 27kV. The following steps describe
modify the original design without obtaining written how to measure the high voltage and how to prevent X-
permission from manufacturer or you will void the original radiation.
parts and labor guarantee.
Note : It is important to use an accurate high voltage
CAUTION: No modification of any circuit should be meter calibrated periodically.
attempted.
Service work should be performed only after · To measure the high voltage, use a high impedance
you are thoroughly familiar with all of the high voltage meter, connect () to chassis and (+) to
following safety checks and servicing the CDT anode cap.
guidelines. · Set the brightness control to maximum point at full
white pattern.
SAFETY CHECK · Measure the high voltage. The high voltage meter
Care should be taken while servicing this color monitor should be indicated at the factory recommended level.
because of the high voltage used in the deflection circuits. · If the meter indication exceeds the maximum level,
These voltages are exposed in such areas as the immediate service is required to prevent the possibility
associated flyback and yoke circuits. of premature component failure.
· To prevent X-radiation possibility, it is essential to use
FIRE & SHOCK HAZARD the specified picture tube.
An isolation transformer must be inserted between the
color monitor and AC power line before servicing the
chassis.
CAUTION:
· In servicing, attention must be paid to the original lead
Please use only a plastic screwdriver to protect yourself
dress specially in the high voltage circuit. If a short
from shock hazard during service operation.
circuit is found, replace all parts which have been
overheated as a result of the short circuit.
· All the protective devices must be reinstalled per the
original design.
· Soldering must be inspected for the cold solder joints,
frayed leads, damaged insulation, solder splashes, or
the sharp points. Be sure to remove all foreign
materials.
IMPLOSION PROTECTION
All used display tubes are equipped with an integral
implosion protection system, but care should be taken to
avoid damage and scratching during installation. Use only
same type display tubes.
-3-
TIMING CHART
VIDEO
C B
D F
E
SYNC
A
FACTORY PRESET MODE
MODE MARK MODE 1 MODE 2 MODE 3 MODE 4 MODE 5
VESA
H Sync Polarity + + + +
O Frequency kHz 43.269 53.674 68.677 91.146 93.750
R
Total Period µs A 23.112 18.631 14.561 10.971 10.666
I
Z Video Active Time µs B 17.778 14.222 10.836 8.127 7.901
O Blanking Time µs C 5.334 4.409 3.725 2.844 2.765
N
Front Porch µs D 1.556 0.569 0.508 0.406 0.316
T
A Sync Duration µs E 1.556 1.138 1.016 1.016 0.948
L Back Porch µs F 2.222 2.702 2.201 1.422 1.501
Sync Polarity + + + +
V Frequency Hz 85.008 85.061 84.997 85.024 75.000
E
Total Period ms A 11.763 11.756 11.765 11.762 13.333
R
T Video Active Time ms B 11.093 11.178 11.183 11.235 12.800
I Blanking Time ms C 0.670 0.578 0.582 0.527 0.533
C
Front Porch ms D 0.023 0.019 0.015 0.011 0.011
A
L Sync Duration ms E 0.069 0.056 0.044 0.033 0.032
Back Porch ms F 0.578 0.503 0.523 0.483 0.490
640 800 1024 1280 1600
Resolution X X X X X
480 600 768 1024 1200
85Hz 85Hz 85Hz 85Hz 75Hz
Recall Yes Yes Yes Yes Yes
-4-
OPERATING INSTRUCTIONS
FRONT VIEW REAR VIEW
USB port
AC Power Socket
See Front Control Panel Power Button
D-Sub Signal Connector
Front Control Panel
3 4 5 2 1
1. Power Button 4. Button
This button is used to turn the monitor ON and Use these buttons to choose or adjust items in
OFF. the on screen display.
2. Power Indicator 100
Button Bring up Contrast adjustment
This Indicator lights up green when the monitor 100
operates normally. If the monitor is in stand-by, Button Bring up Brightness adjustment
suspend or DPMS off mode, this indicator color
changes to amber. The Contrast and Brightness functions are also available in
the On Screen Display (OSD) menu.
3. MENU (or OSD) Button
Use this button to enter or exit the on screen 5. SELECT Button
Use this button to enter a selection in the on
display.
screen display.
-5-
Universal Serial Bus
Making use of USB (Universal Serial Bus)*
USB(Universal Serial Bus) is an innovation in connecting your different desktop peripherals conveniently to your
computer. By using the USB, you will be able to connect your mouse, keyboard and other peripherals to your
monitor instead of having to connect them to your computer. This will give you greater flexibility in setting up
your system. USB allows you to connect chain up to 120 devices on a single USB port, and you can "hot" plug
(attach them while the computer is running) or unplug them while maintaining Plug and Plug auto detection and
configuration. This monitor has an integrated Bus-powered USB hub, allowing up to 2 other USB devices to be
attached it.
USB connection (Option)
(1) Connect the upstream port of the monitor to the downstream port of the USB
compliant PC or another hub using the USB cable.
(2) Connect the USB compliant peripherals to the downstream ports the monitor.
*USB(Universal Serial Bus) is supported WINDOWS98 and Higher.
USB Downstream Ports
Connect the cables from USB compliant
peripherals-such as keyboard, mouse etc.
USB Upstream Port
To USB downstream port
of the USB compliant PC
or another hub cable
USB Upstream connector USB Downstream connector
-6-
CONTROL LOCATIONS
VR801
: High Voltage Adjustment (27kV)
VR901
:B + Adjustment (190V Line)
-7-
WIRING DIAGRAM
P250 P201
P401
P402
P801
P453 P451
P902
FBT
S+
S-
P901
P702
AC
Socket P910
P502
Signal
Cable
P302 P301
P303
-8-
DISASSEMBLY
1. TILT/SWIVEL & BACK COVER REMOVAL
1) Set the monitor face downward.
2) Carefully remove the Tilt/Swivel by pulling it upward.
3) Remove two screws (a).
4) Pressing the latch (b), Back cover by pushing it upward. (See Figure. 1)
5) Release the latch (c). (See Figure. 2 and Tip Spec.)
6) Slide the Back Cover away from the Front Cabinet of the monitor.
(a)
Figure. 1
(a)
(b)
Figure. 2
Tip Spec.
A(Width) : 5.0~15.0mm
C
B(Depth) : 0.6~0.9mm
Tip
C(Height) : 12.0mm A
B
Bac
k Co
ver
(c)
Ca
bin
et
-9-
BLOCK DIAGRAM
SIGNAL
INPUT
- 10 -
DESCRIPTION OF BLOCK DIAGRAM
1. Line Filter & Associated Circuit. 5. X-ray Protection.
This is used for suppressing noise of power input line This circuit detects the rectified DC voltage comes
flowing into the monitor and/or some noise generated from the FBT pin 4. If the high voltage of the FBT
in this monitor flowing out through the power input reaches up to about 30kV (abnormal state), H.V
line. control (IC802) detects. It stops B+ voltage supplied to
That is to say, this circuit prevents interference the FBT (T701), and high voltage is not be generated,
between the monitor and other electric appliances. (In the normal state, the high voltage is about 26kV.)
2. Degauss Circuit & Coil. 6. Micom(Microprocessor) Circuit.
The degauss circuit consists of the degaussing coil, The operating procedure of Micom (Microprocessor)
the PTC (Positive Temperature Coefficient) thermistor and its associated circuit is as follows:
(TH901), and the relay (RL901). This circuit eliminates
1) H and V sync signal is supplied from Signal Cable to the
abnormal color of the screen automatically by
Micom (IC401).
degaussing the slot mask in the CDT when turn on the
power switch. 2) The Micom (IC401) distinguishes polarity and
When you need to degauss while using the monitor, frequency of H and V sync.
select DEGAUSS on the OSD menu.
3) The Micom controls each OSD function signals.
(H-size, H-position, V-size, etc.)
3. SMPS (Switching Mode Power Supply).
4) The controlled data of each mode is stored in IC402.
This circuit works with power of 100~240V or
User can adjust screen condition by each OSD
200~240V (50/60Hz) specially for PFC version.
function. The data of the adjust screen condition is
The operation procedure is as follows: stored automatically.
1) AC input voltage is rectified and smoothed by
7. Horizontal and Vertical Synchronous Processor.
the bridge diode (D901) and the capacitor (C905).
This circuit generates the horizontal drive pulse and
2) The rectified voltage (DC voltage) is applied to the
the vertical drive pulse by taking sync-signal from
primary coil of the transformer (T901).
Signal Cable. This circuit consists of the
3) The control IC (IC901) generates switching pulse TDA4841(IC801) and the associated circuit.
to turn on and off the primary coil of the
transformer (T901) repeatedly. 8. Oscillating Circuit for D/D Converter.
4) Depending on the turn ratio of the transformer, the This circuit generates the pulse wave which has the
secondary voltages appear at the secondary coil of horizontal period by taking the output of the
the transformer (T901). TDA4841(IC801).
5) These secondary voltages are rectified by each
9. D/D (DC to DC) Converter.
diode (D924, D926, D923, D929, D922, D921,
D920) and operate the other circuits. (Deflection, This circuit supplies DC voltage to the horizontal
Video Amplifier, etc.) deflection output circuit by decreasing DC 192V which
is the secondary voltage of the SMPS in accordance
4. Display Power Management Circuit. with the input horizontal sync signal.
This circuit control power consumption of the monitor
10. D/D Drive & Convert Circuit.
by detecting H and V sync signal. There are stand-by
and suspend mode. When no horizontal or vertical This circuit is used for supplying B + voltage to
sync signal input, the circuit consists of Q913, Q915 horizontal deflection output transistor (Q801).
and IC401 control signal becomes stand-by and
suspend mode. It's power consumption is below 8W. 11. Horizontal Deflection Output Circuit.
When no horizontal and vertical sync signal input, it's
This circuit makes the horizontal deflection by
power consumption is below 1W.
supplying the saw-tooth current to the horizontal
deflection yoke.
- 11 -
12. High Voltage Output & FBT (Flyback Transformer). 18. Static Convergence Control Circuit.
The high voltage output circuit is used for generating This circuit corrects the convergence of the screen by
pulse wave to the primary coil of the FBT (Flyback supplying the convergence signal to the 4H (STC) coil
Transformer (T701)). A boosted voltage (about 27kV) which is attached to the CDT near the deflection.
appears at the secondary of the FBT and it is supplied
to the anode of the CDT. 19. Moire Reduction Circuit
And there are another output voltages such as the
This circuit reduce interference between the periodical
dynamic focus voltage.
display pattern and the CDT's slot (or dot).
The positions of every other one dot video signal
13. H-Linearity Correction Circuit.
beams (red, green, and blue beam) are shifted finely,
This circuit corrects the horizontal linearity for each thus reducing interference.
horizontal sync frequency.
20. OSD Circuit.
14. Vertical Output Circuit.
This circuit is used for performing the OSD (On-
This circuit takes the vertical wave from the Screen- Display) function.
TDA4841(IC801) and performs the vertical deflection When a user selects the OSD Select/Adjustment
by supplying the saw-tooth wave current from the control, the adjustment status displays on the screen.
TDA4867J (IC601) to the vertical deflection yoke.
21. Video Pre-Amp Circuit.
15. Dynamic Focus Output Circuit.
This circuit amplifies the analog video signal from 0-
This circuit takes H and V parabola wave from the 0.7V to 0-4V. This circuit is operated by taking the
TDA4841(IC801), and amplifies these waves to offer clamp, R, G, B drives, and contrast signals from the
to the FBT (T701). Micom (IC401).
16. H & V Blanking and Brightness Control. 22. Video Output Amp Circuit.
This circuit eliminates the retrace line by supplying a This circuit amplifies the video signal which comes
negative pulse to the G1 of the CDT. from the video pre-amp circuit and amplified video
signal is applied to the CDT cathode.
17. Image Rotation (Tilt) Circuit.
This circuit corrects the tilt of the screen by supplying
the image rotation signal to the tilt coil which is
attached to the CDT near the deflection.
- 12 -
ADJUSTMENT
GENERAL INFORMATION
All adjustment are thoroughly checked and corrected 3) EEPROM ALL CLEAR Y(Yes) command.
when the monitor leaves the factory, but sometimes Do not run this procedure unless the
several adjustments may be required. EEPROM is changed. All data in EEPROM (mode
Adjustment should be following procedure and after data and color data) will be erased.
warming up for a minimum of 30 minutes. 4) COMMAND PRESET START Y(Yes)
command.
· Alignment appliances and tools. 5) DIST. ADJ. FOS. ADJ command.
- IBM compatible PC. 6) Adjust H-POSITION as arrow keys to center of the
- Programmable Signal Generator. screen.
(eg. VG-819 made by Astrodesign Co.) 7) Adjust H-SIZE as arrow keys to 350 ± 2mm.
- EPROM or EEPROM with saved each mode data. 8) Adjust V-POSITION as arrow keys to center of the
- Alignment Adaptor and Software. screen.
- Digital Voltmeter. 9) Adjust V-SIZE as arrow keys to 262 ± 2mm.
- White Balance Meter. 10) Adjust TRAPEZOID as arrow keys to be the best
- Luminance Meter. condition.
- High-voltage Meter. 11) Adjust SIDE PINCUSHON as arrow keys to be the
best condition.
AUTOMATIC AND MANUAL DEGAUSSING 12) Adjust TILT as arrow keys to be the best condition.
The degaussing coil is mounted around the CDT so that 13) Display cross hatch pattern at Mode 4.
automatic degaussing when turn on the monitor. But a 14) DIST. ADJ. BALANCE DATA command.
monitor is moved or faced in a different direction, become 15) Adjust balance of Pin-Balance as arrow keys to be
poor color purity cause of CDT magnetized, then press the best condition.
DEGAUSSING on the OSD menu. 16) Adjust parallelogram as arrow keys to be the best
condition.
17) Save of the Mode.
ADJUSTMENT PROCEDURE & METHOD 18) Save of the System.
19) Display from Mode 4 and repeat above from
- Install the cable for adjustment such as Figure 1and run number 6) to 16).
the alignment program on the DOS for IBM compatible PC. 20) COMMAND PRESET EXIT Y (Yes) command.
- Set external Brightness and Contrast volume to max position.
5. Adjustment for White Balance and Luminance.
1. Adjustment for B+ Voltage.
1) Set the White Balance Meter.
1) Display cross hatch pattern at Mode 4. 2) Press the DEGAUSSING on the OSD menu for
2) Adjust C905 (+) voltage to 190V ± 0.5V with VR901. demagnetization of the CDT.
3) Display color 0,0 pattern at Mode 4.
2. Adjustment for High-Voltage. 4) COMMAND PRESET START Y(Yes)
1) Display cross hatch pattern at Mode 4. command.
2) Adjust CDT Anode voltage to 27kV ± 0.2kV with 5) Set Bightness and Contrast to max position.
VR801. 6) COLOR ADJ. LUMINANCE command of the
alignment program.
3. Adjustment for Horizontal Raster Center. 7) COLOR ADJ. BIAS ADJ. command of the
alignment program.
1) Display cross hatch pattern at Mode 4. 8) Check whether blue color or not at R-BIAS and G-
2) Adjust the Back Raster should be center of the BIAS to min position, Sub-Brightness to 90
screen with SW801. (5A(h))position, B-BIAS to 70(46(h))position. If it's
not blue color, the monitor must repair.
4. Adjustment for Factory Mode (Preset Mode). 9) Adjust Screen control on the FBT to 0.15 ± 0.05FL
of the raster luminance.
1) Display cross hatch pattern at Mode All.
10) Adjust R-BIAS and G-BIAS command to x=0.283 ±
2) Run alignment program for F900BJ on the IBM
0.006 and y=0.298 ± 0.006 on the White Balance
compatible PC.
Meter with PC arrow keys.
- 13 -
11) Display color 15,0 Full White(70x70mm) at mode 4. 6. Adjustment for Focus.
12) DRIVE ADJ command.
1) Display H character in full screen at Mode 4.
13) Set B-DRIVE to 94(5E(h)) at DRIVE of the
2) Adjust two Focus control on the FBT that focus
alignment program.
should be the best condition.
14) Adjust R-DRIVE and G-DRIVE command to white
balance x=0.283 ± 0.003 and y=0.298 ± 0.003 on
the White Balance Meter with PC arrow keys.
15) Adjust SUB-CONTRAST command to 40±1FL of
the raster luminance.
15) Display color 15,0 full white patten at Mode 4.
16) COLOR ADJ. LUMINANCE ABL command.
17) Adjust ABL to 30 ± 1FL of the luminance.
18) Exit from the program.
- 14 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
CHECK
NO TROUBLE IN
FUSE OK?
FUSE (F901)
(F901)
YES
CHECK
D901 NO TROUBLE IN
BRIDGE DIODE? BRIDGE DIODE
(D901)
YES
CHECK
C905(+) VOLTAGE NO
145VDC at 110V input TROUBLE IN
310VDC at 220V input IC901
YES
CHECK
NO TROUBLE IN
D924, D926, D923,
D922, D921, D920 ? D924, D926, D923,
D922, D921, D920
YES
TROUBLE IN
Q912, Q913, Q915, Q914,
IC903, IC904, Q902
- 15 -
2. NO CHARACTER
NO CHARACTER
TROUBLE IN
CHECK NO
P301, SIGNAL CABLE,
IC302 PIN 5, 6, 7 ?
PC SIGNAL
YES
CHECK
IC302 PIN 19, 20, 21 NO TROUBLE IN
PIN 10 (5V) ? IC302, P302
YES
CHECK
IC303 PIN 1, 3, 5 NO TROUBLE IN
PIN10 (12V), IC303
PIN 6 (80V) ?
YES
CHECK
R, G, B CATHODE NO TROUBLE IN
VOLTAGE? IC304
YES
TROUBLE IN
CDT SOCKET
- 16 -
3. NO RASTER
NO VIDEO
(POWER INDICATOR
GREEN or AMBER)
CHECK
POWER INDICATOR AMBER
TROUBLE IN
GREEN or AMBER ? P302 SIGNAL CABLE
GREEN
CHECK
ROTATE SCREEN
SCREEN CONTROL
CONTROL KNOB TO
KNOB OF FBT
CLOCKWISE or
COUNTER CLOCKWIES
OK
CHECK
VOLTAGE AT
D924/D926 CATHODE (190V) NO TROUBLE IN PRIMARY
D923/D929 CATHODE (80V) CIRCUIT OF T901
IC904 OUT (12V)
D921 CATHODE
(6.3V)?
YES
CHECK
IC401 (MICOM) PIN 6 NO TROUBLE IN
5V (HIGH), IC801 PIN 10 CDT SOCKET, BOARD
12V (HIGH)?
YES
TROUBLE IN
IC401 (MICOM),
IC801
- 17 -
4. NO VERTICAL DEFLECTION
NO V-DEFLECTION
(ONE HORIZONTAL LINE)
CHECK NO TROUBLE IN
IC601 Pin 3
T901 15V LINE
(15V) ?
YES
CHECK NO TROUBLE IN
IC601 PIN 7 T701 47V LINE
(47V)?
YES
CHECK
IC801 PIN 12 NO TROUBLE IN
(SAWTOOTH WAVE)? IC801
YES
TROUBLE IN
IC601, V-CIRCUIT
- 18 -
5. TROUBLE IN DPM
STAND-BY/SUSPEND/
DPMS OFF MODE FAILURE
CHECK
CHECK PC,
IC401 (MICOM) INPUT H/V SYNC SIGNAL
(PC IS NOT GOING INTO
PIN 40, 41 (H/V INPUT)
DPM MODE)
SIGNAL?
NO H/V SYNC SIGNAL
CHECK
NO TROUBLE IN
IC401 PIN 9, 8
X401, IC401
WAVEFORM?
YES
CHECK
NO TROUBLE IN
IC401 PIN 6
(5V, HIGH)? IC401
YES
CHECK
NO TROUBLE IN
IC401 PIN 17, 18 ?
IC401
YES
CHECK
B+ LINE NO TROUBLE IN
(12V, 15V, 80V, Q913, Q915
5V) ?
DPMS TABLE
Item H / V SYNC VIDEO LED
Mode
NORMAL ON / ON NORMAL GREEN
TROUBLE IN OFF / ON OFF(0V) AMBER
STAND-BY
T901 or PC
SUSPEND ON / OFF OFF(0V) AMBER
OFF OFF / OFF OFF(0V) AMBER
- 19 -
6. NO DEGAUSSING
NO DEGAUSSING
CHECK NO TROUBLE IN
IC401 PIN 6
IC401 (MICOM)
(5V)?
YES
CHECK
Q920 COLLECTOR NO TROUBLE IN
VOLTAGE D925
(0.5V)?
YES
CHECK NO TROUBLE IN
P901? P901
YES
CHECK NO TROUBLE IN
RL901? RL901
YES
TROUBLE IN
TH901,
DEGAUSSING COIL
- 20 -
EXPLODED VIEW
16
3
5
6
b
c 8
17
6-1 d
b
9
b a
10
- 21 -
2 11
B 4
7
12
13
b
14
b
d
15
a
c d
c b
14
1
15
A
EXPLODED VIEW PARTS LIST
Ref. No. Part No. Description
1 3091TKC095A CABINET ASSEMBLY, F900BJ BRAND TKC075A LGC (ER04) B/A SW
2 6318L19008A CDT(CIRC), M46QDG423X11NDDD LG-PHILIPS 107KHZ 29.1MM FLATRON TCO V2
3809TKC045D BACK COVER ASSEMBLY, FB990G 3808TKC044 PFC/TCO99 - For Euope
3
3809TKC045A BACK COVER ASSEMBLY, FB990G 3808TKC044 BRAND-8C358 - For U.S.A, Canada, Israel, Saudi
4 3043TKK101A TILT SWIVEL ASSEMBLY, FB990G/FB910G TKB059/TKT064 2ND FLAT BRAND
5 339-002J SCREW ASSY, PHP+5*25 (FZMW1)+GW18
6 4951TKS041H METAL ASSEMBLY, FRAME FB990G,PEM NUT BOTTOM FRAME
6-1 6140TC2017A COIL,DEGAUSSING, - GET 0.6*90T,14 OHM,WITH PURITY FB790G
7 6871TST378A PWB(PCB) ASSEMBLY,SUB, F900BJ CONTROL TOTAL BRAND .
8 6174T13010K FBT (FLY BACK TRANSFORMER), FQM19A013,T910BJ(98K) SAMSUNG 19"
9 6200TJB001N FILTER(CIRC),EMC, 02MD5 DELTA BK F900BJ
10 6850TA9009N CABLE,D-SUB, UL20276-9C(5.8MM) AT 1560MM GRAY(85964) T910BJ DM
11 4950TKK450A METAL, REAR BRACKET FB990G
12 6871TUT028A PWB(PCB) ASSEMBLY,USB, F700PJ SUB TOTAL BRAND .
13 4951TKK090E METAL ASSEMBLY, SHIELD BOTTOM-FB990J
14 4930TKK031C HOLDER, PCB FIX, PCT ABS
15 332-102E SCREW,, PTP+4*16(MSWR/FZMY)
16 4815TKT009A SHIELD ASSY, TOP (FB915B)
17 332-102E SCREW,, PTP+4*16(MSWR/FZMY)
3313T19054B MAIN TOTAL ASSEMBLY, F900BJ BRAND CA-130 - For Euope
A 3313T19054D MAIN TOTAL ASSEMBLY, F900BJ BRAND CA-130 - For U.S.A, Canada
3313T19054A MAIN TOTAL ASSEMBLY, F900BJ BRAND CA-130 - For Israel, Saudi
6871TMT408B PWB(PCB) ASSEMBLY,MAIN, F900BJ ALRPE BRAND CA-130 TOTAL - For Euope
B 6871TMT408C PWB(PCB) ASSEMBLY,MAIN, F900BJ ALUSE BRAND CA-130 TOTAL - For U.S.A, Canada, Israel
6871TMT408A PWB(PCB) ASSEMBLY,MAIN, F900BJ ALRDE BRAND CA-130 TOTAL - For Saudi, Israel
a 332-112F SCREW,DRAWING, D3.5 L10.0 MSWR/FZMY +SW3.5+RW3.5
b 4001TKK004E SCREW ASSEMBLY, TAPTITE P TYPE D3.0 L10.0 MSWR/FZMY SW3+RW10
c 339-008C SCREW ASSY, MP+3*10(FZMY)+SW3+RW3
d 332-095B SCREW,DRAWING, PZP+3*10(MSWR/FZMY)
- 22 -
REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,
READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY Mark
AL ALTERNATIVE PARTS
DATE: 2003. 4. 18. DATE: 2003. 4. 18.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
MAIN BOARD
CAPACITORS C459 0CK1010K515 100PF 50V K B TR
C460 0CE475CK638 4.7UF SHL,SD 50V M FM5 TP 5
C301 0CK1020K515 1000PF 50V K B TR C601 0CQ6821N419 6800PF 100V J PE NI TP
C303 0CK3320K515 3300P 50V K B TS C602 181-288Q MKT 100V 154JTR PHS26154
C304 181-288B MKT 100V 104JTR PHS26104 C603 0CK1020W515 1000P 500V K B TS
C306 181-288N MKT 100V 103JTR PHS86103 C605 0CE476CN618 47UF SHL 100V M FL TP5
C307 0CK1030K945 0.01UF 50V Z F TR C611 0CE108CH618 1000UF SHL 25V M FL TP5
C308 0CK1040K945 0.1UF 50V Z F TR C701 0CE106CK638 10UF SHL,SD 50V M FM5 TP 5
C309 0CK1040K945 0.1UF 50V Z F TR C702 0CE3376N650 330M SMS 100V M FM7.5
C310 181-288E MKT 100V 474JTR PHS 26474 C704 0CBZTBU003M 562J 20.0*14.0*8.5*10.0 800V
C311 181-288B MKT 100V 104JTR PHS26104 C705 0CE336CN638 33UF SHL,SD 100V M FM5 TP 5
C312 181-288B MKT 100V 104JTR PHS26104 C707 0CE106CK638 10UF SHL,SD 50V M FM5 TP 5
C313 181-288B MKT 100V 104JTR PHS26104 C708 0CE476CQ618 47U SHL 200V M FL TP5
C315 0CE476CF638 47UF SHL,SD 16V M FM5 TP 5 C709 181-477A 102J 19.5*12.0*7.0*7.5 250V
C317 0CK1040K945 0.1UF 50V Z F TR C710 0CC3300K405 33P 50V J SL TP
C318 0CN1040K949 0.1M 50V Z F TA52 C711 0CQ4721N419 0.0047U 100V J POLY NI TP5
C319 0CK1040K945 0.1UF 50V Z F TR C712 0CK2220K515 2200P 50V K B TS
C320 0CE107CN630 100U SHL 100V M FM5 C713 0CE107CH638 100UF SHL,SD 25V M FM5 TP 5
C321 0CK1040K945 0.1UF 50V Z F TR C730 0CE476CH638 47UF SHL,SD 25V M FM5 TP 5
C323 0CE107CH638 100UF SHL,SD 25V M FM5 TP 5 C731 0CE105CK638 1UF SHL,SD 50V 20% FM5 TP 5
C324 0CN1040K949 0.1M 50V Z F TA52 C732 0CK1040K945 0.1UF 50V Z F TR
C325 181-288E MKT 100V 474JTR PHS 26474 C734 181-288T MKT 100V 223KTR PHS85223
C328 0CE476CN618 47UF SHL 100V M FL TP5 C735 0CK10302945 0.01UF 2KV Z F TR
C330 181-288B MKT 100V 104JTR PHS26104 C736 0CK10302945 0.01UF 2KV Z F TR
C331 181-288E MKT 100V 474JTR PHS 26474 C738 0CE685CN638 6.8UF SHL,SD 100V 20% TP 5 F
C332 181-288E MKT 100V 474JTR PHS 26474 C739 0CK1040K945 0.1UF 50V Z F TR
C333 181-288E MKT 100V 474JTR PHS 26474 C740 0CE106EK638 10UF KMG 50V M FM5 TP 5
C334 181-288B MKT 100V 104JTR PHS26104 C741 0CC1000W105 10PF 500V D SL TR
C335 181-288B MKT 100V 104JTR PHS26104 C742 0CC1000W105 10PF 500V D SL TR
C339 0CK2710W515 270P 500V K B TS C743 0CE106CN638 10UF SHL,SD 100V M FM5 TP 5
C340 181-288B MKT 100V 104JTR PHS26104 C744 0CN1020K519 1000P 50V K B TA52
C341 0CK10302945 0.01UF 2KV Z F TR C771 0CK6810K515 680P 50V K B TS
C342 0CC2200W415 22PF 500V J NP0 TR C772 0CK4710W515 470P 500V K B TS
C344 181-288C MKT 100V 224JTR PHS 26224 C801 0CQ6821N419 6800PF 100V J PE NI TP
C346 0CK10202515 1000PF D 2KV 10% TR B(Y5P) C802 181-288B MKT 100V 104JTR PHS26104
C347 0CK10302940 0.01M 2KV Z F S C803 0CE106CK638 10UF SHL,SD 50V M FM5 TP 5
C355 0CE476CF638 47UF SHL,SD 16V M FM5 TP 5 C804 181-288D MKT 100V 473JTR PHS26473
C372 0CN1040K949 0.1M 50V Z F TA52 C805 181-476R 2200 D 100V H PP NI TP5
C401 0CC5600K415 56P 50V J NP0 TP C806 0CE227CH638 220UF SHL,SD 25V M FM5 TP 5
C402 0CE476CH638 47UF SHL,SD 25V M FM5 TP 5 C807 181-288B MKT 100V 104JTR PHS26104
C403 0CK2710K515 270P 50V K B TS C808 0CC1000K115 10P 50V D NP0 TS
C404 0CK2710K515 270P 50V K B TS C809 0CK1020K515 1000PF 50V K B TR
C405 0CK2710K515 270P 50V K B TS C810 0CE105CK638 1UF SHL,SD 50V 20% FM5 TP 5
C406 0CC0400K115 4P 50V D NP0 TS C811 0CE476CH638 47UF SHL,SD 25V M FM5 TP 5
C407 0CC0400K115 4P 50V D NP0 TS C812 0CE107CH638 100UF SHL,SD 25V M FM5 TP 5
C410 0CK1040K945 0.1UF 50V Z F TR C813 0CE106CK638 10UF SHL,SD 50V M FM5 TP 5
C417 0CK1040K945 0.1UF 50V Z F TR C814 0CK5610K515 560P 50V K B TS
C452 0CE106CK638 10UF SHL,SD 50V M FM5 TP 5 C815 0CE227CF638 220UF SHL,SD 16V M FM5 TP 5
C453 0CE106CK638 10UF SHL,SD 50V M FM5 TP 5 C817 0CE476CH638 47UF SHL,SD 25V M FM5 TP 5
C454 0CK1040K945 0.1UF 50V Z F TR C818 181-288J MKT 100V 563JTR PHS26563
C455 0CK1040K945 0.1UF 50V Z F TR C819 181-477U 333J 19.5*13.0*7.5*7.5 250V
C456 0CN1040K949 0.1M 50V Z F TA52 C821 0CN1040K949 0.1M 50V Z F TA52
C457 181-288E MKT 100V 474JTR PHS 26474 C823 0CK1010K515 100PF 50V K B TR
C458 0CK1040K945 0.1UF 50V Z F TR C832 0CK10102515 100PF D 2KV 10% B(Y5P) TR
- 23 -
DATE: 2003. 4. 18. DATE: 2003. 4. 18.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
DIODEs
C833 181-482D 184J 18.0*15.0*8.5*7.5 250V
C834 0CN1040K949 0.1M 50V Z F TA52 D301 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C835 0CBZTTA001R 103J 20.0*17.0*10.0*7.5 800V D302 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C841 0CE476CR630 47UF SHL,SD 250V M FM5 BULK D303 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C842 181-309H 272J 23.0*17.0*10.0*15.0 1.6 D304 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C843 0CQ3321N419 3300P 100V J POLY NI TP D305 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C844 181-309H 272J 23.0*17.0*10.0*15.0 1.6 D306 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C845 181-288B MKT 100V 104JTR PHS26104 D307 0DS124409AA 1SS244 TP ROHM KOREA
C846 0CE108EF618 1000UF KMG 16V M FL TP 5 D308 0DS124409AA 1SS244 TP ROHM KOREA
C847 0CQ2221N419 2200PF 100V J PE NI TP D309 0DS124409AA 1SS244 TP ROHM KOREA
C848 0CK47101515 470P 1KV K B TS D310 0DS124409AA 1SS244 TP ROHM KOREA
C849 0CK6810W515 680P 500V K B TS D311 0DS124409AA 1SS244 TP ROHM KOREA
C850 0CK1040K945 0.1UF 50V Z F TR D312 0DS124409AA 1SS244 TP ROHM KOREA
C851 0CK1040K945 0.1UF 50V Z F TR D313 0DS124409AA 1SS244 TP ROHM KOREA
C852 0CN1040K949 0.1M 50V Z F TA52 D314 0DS124409AA 1SS244 TP ROHM KOREA
C854 181-482W 304J 19.0*18.5*10.5*7.5 250V D315 0DS124409AA 1SS244 TP ROHM KOREA
C855 181-477Z 823J 20.0*17.5*10.0*7.5 250V D316 0DR140059DA 1N4005TB52 TP LITEON DO41 60
C856 181-482G 334J 18.0*18.0*11.0*7.5 250V D401 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C857 181-305M 824J 26.0*21.5*13.0*15.0 25 D402 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C858 181-303A 104J 20.5*18.5*10.5*10.0 250 D405 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C859 181-478B 124J 20.0*19.0*11.0*7.5 250V D451 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C860 0CN1040K949 0.1M 50V Z F TA52 D452 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C861 0CN1040K949 0.1M 50V Z F TA52 D453 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C863 0CN1040K949 0.1M 50V Z F TA52 D454 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C864 0CN1040K949 0.1M 50V Z F TA52 D701 0DR400409AC UF4004 GULF TP DO41 400V 1A
C865 0CE105CK638 1UF SHL,SD 50V 20% FM5 TP 5 D702 0DR400409AC UF4004 GULF TP DO41 400V 1A
C891 0CZZTFT001J ECQB1H562JM3 562J 50V TP5.0 D703 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C892 0CZZTFT001M ECQB1H103JF3 MATSUSHITA 50V D704 0DR100009CA RGP10G TP GULF SEMICONDUCTOR
C893 181-288B MKT 100V 104JTR PHS26104 D706 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C894 0CZZTFT001L ECQB1H822JM3 822J 50V TP5.0 D707 0DR100009DA RGP10J TP GULF SEMICONDUCTOR
C895 181-288B MKT 100V 104JTR PHS26104 D708 0DRFJ00011A YG339D6F208 FUJI ST TO220 -4
C896 181-288Q MKT 100V 154JTR PHS26154 D731 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C902 0CKZTTA003C SC E 472M 14.0FF7 250V TP7.5 D732 0DD400709CB UF4007 TP G.I DO204AL 1000V
C903 0CK10101515 100PF 1KV K B TR D733 0DD400709CB UF4007 TP G.I DO204AL 1000V
C904 181-304V 393J 19.5*15.5*9.5*10.0 400V D734 0DD400709CB UF4007 TP G.I DO204AL 1000V
C905 0CZZTAB001B SMH/HC 470UF 400V 30*50 BK10 - only U.S.A, Canada D735 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C905 181-296F 330UF SMH(30*40) 400V M VNS D736 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C906 0CE475CN638 4.7UF SHL,SD 100V M FM5 TP 5 D737 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C907 0CE336CK638 33UF SHL,SD 50V M FM5 TP 5 D738 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C908 0CK1040K945 0.1UF 50V Z F TR D740 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C909 181-288T MKT 100V 223KTR PHS85223 D771 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C910 0CZZTFT001N ECQB1H123JM3 123J 50V TP5.0 D772 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C911 0CE108CD618 1000UF SHL 10V M FL TP5 D773 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C912 0CE475CK638 4.7UF SHL,SD 50V M FM5 TP 5 D801 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C915 0CE476CH638 47UF SHL,SD 25V M FM5 TP 5 D802 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C916 0CK2220K515 2200P 50V K B TS D803 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C917 0CKZTTA003C SC E 472M 14.0FF7 250V TP7.5 D804 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C918 0CKZTTA003C SC E 472M 14.0FF7 250V TP7.5 D805 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C920 0CC47001505 47PF 1KV K SL TR D808 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C921 0CE227CR650 220UF SHL 250V M FM7.5 BULK D811 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C922 0CE3376N650 330M SMS 100V M FM7.5 D812 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C923 0CK1010W515 100P 500V K B TS D831 0DR260400AA S2L60-4004P15 BK SHINDENGEN
C925 0CE228CH618 2200U SHL 25V M FL TP5 D833 0DR140059DA 1N4005TB52 TP LITEON DO41 60
C926 0CE108EF618 1000UF KMG 16V M FL TP 5 D834 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C927 0CE228CH618 2200U SHL 25V M FL TP5 D835 0DRGF00069A SB140 GULF TP DO41 40V 1A 40
C928 0CE108EF618 1000UF KMG 16V M FL TP 5 D836 0DRGF00069A SB140 GULF TP DO41 40V 1A 40
C929 0CK1020K515 1000PF 50V K B TR D837 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C930 0CQ2721N419 2700PF 100V J PE NI TP D838 0DR200000EA FMQ-G2FMS BK SANKEN NON 1500
C931 0CK1010W515 100P 500V K B TS D839 0DS141489AB 1N4148 TP GRANDE DO-34 500MW
C932 0CC47001505 47PF 1KV K SL TR D840 0DR100009DA RGP10J TP GULF SEMICONDUCTOR
C953 0CE477CF638 470UF SHL TYPE 16V M FM5 TP D861 0DD140009AA EK14 V(1) TP SANKEN E/EO-TMD
C970 0CE476CH638 47UF SHL,SD 25V M FM5 TP 5 D901 0DRGF00090A GBL06 GULF BK GBL 600V 4A 12
- 24 -
DATE: 2003. 4. 18. DATE: 2003. 4. 18.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
D902 0DRGF00109A GUF10M GULF TP DO41 1000V 1A FB304 125-022J FERRITE KQ-1 JS 3.5*5.0MM AX
D903 0DR100009CA RGP10G TP GULF SEMICONDUCTOR FB305 125-155J BFS2550A0FG SAMWHA 2.5*5.0MM
D904 0DR100009DA RGP10J TP GULF SEMICONDUCTOR FB306 125-155A BFD3510R2FG SAMWHA 3.5*10MM
D905 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB309 125-155B BFS3580R2FG SAMWHA 3.5*8.0MM
D906 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB310 125-155A BFD3510R2FG SAMWHA 3.5*10MM
D907 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB311 125-155A BFD3510R2FG SAMWHA 3.5*10MM
D908 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB401 125-155J BFS2550A0FG SAMWHA 2.5*5.0MM
D909 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB402 125-155N BFD3565R2FG SAMWHA 3.5*6.5MM
D910 0DRGF00139A GPP20J GULF TP DO15 600V 2.0 FB403 125-155L BFS3580A0FG SAMWHA 3.5*8.0MM
D911 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB404 125-155F BFD3580R2FG SAMWHA 3.5*8.0MM
D912 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB405 125-155F BFD3580R2FG SAMWHA 3.5*8.0MM
D913 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB406 125-155A BFD3510R2FG SAMWHA 3.5*10MM
D914 0DS141489AB 1N4148 TP GRANDE DO-34 500MW FB407 125-155A BFD3510R2FG SAMWHA 3.5*10MM
D920 0DRSD00079A D2L20U SHINDENGEN TP DO-204A FB701 125-155J BFS2550A0FG SAMWHA 2.5*5.0MM
D921 0DRSD00079A D2L20U SHINDENGEN TP DO-204A FB801 125-155J BFS2550A0FG SAMWHA