Text preview for : lm3886.pdf part of National Semiconductor LM3886 40W AUDIO PWR AMP. WITH M
Back to : lm3886.pdf | Home
LM3886 Overture Audio Power Amplifier Series High-Performance 68W Audio Power Amplifier w Mute
April 1995
LM3886 Audio Power Amplifier Series High-Performance 68W Audio Power Amplifier w Mute
General Description
The LM3886 is a high-performance audio power amplifier capable of delivering 68W of continuous average power to a 4X load and 38W into 8X with 0 1% (THD a N) from 20 Hz 20 kHz The performance of the LM3886 utilizing its Self Peak Instantaneous Temperature ( Ke) (SPiKe) Protection Circuitry puts it in a class above discrete and hybrid amplifiers by providing an inherently dynamically protected Safe Operating Area (SOA) SPiKe Protection means that these parts are completely safeguarded at the output against overvoltage undervoltage overloads including shorts to the supplies thermal runaway and instantaneous temperature peaks The LM3886 maintains an excellent Signal-to-Noise Ratio of greater than 92 dB with a typical low noise floor of 2 0 mV It exhibits extremely low (THD a N) values of 0 03% at the rated output into the rated load over the audio spectrum and provides excellent linearity with an IMD (SMPTE) typical rating of 0 004%
Features
Y Y Y Y Y Y Y
Y
Y
Y
68W cont avg output power into 4X at VCC e g 28V 38W cont avg output power into 8X at VCC e g 28V 50W cont avg output power into 8X at VCC e g 35V 135W instantaneous peak output power capability Signal-to-Noise Ratio t 92 dB An input mute function Output protection from a short to ground or to the supplies via internal current limiting circuitry Output over-voltage protection against transients from inductive loads Supply under-voltage protection not allowing internal biasing to occur when lVEEl a lVCCl s 12V thus eliminating turn-on and turn-off transients 11-lead TO-220 package
Applications
Y Y Y Y Y
Component stereo Compact stereo Self-powered speakers Surround-sound amplifiers High-end stereo TVs
Typical Application
Connection Diagram
Plastic Package (Note 8)
TL H 11833 2
Top View Order Number LM3886T or LM3886TF See NS Package Number TA11B for Staggered Lead Non-Isolated Package or TF11B for Staggered Lead Isolated Package
Preliminary call you local National Sales Rep or distributor for availability
TL H 11833 1
FIGURE 1 Typical Audio Amplifier Application Circuit
Optional components dependent upon specific design requirements Refer to the External Components Description section for a component functional description
OvertureTM and SPiKeTM Protection are trademarks of National Semiconductor Corporation C1995 National Semiconductor Corporation
TL H 11833
RRD-B30M75 Printed in U S A
Absolute Maximum Ratings (Notes 1
2) Soldering Information T Package (10 seconds) Storage Temperature Thermal Resistance iJC iJA 260 C
b 40 C to a 150 C
If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications Supply Voltage lV
a a
Supply Voltage lV l a lV l (Input Signal) 84V a b Common Mode Input Voltage (V or V ) and lV a l a lVb l s 80V Differential Input Voltage (Note 12) 60V Output Current Internally Limited Power Dissipation (Note 3) 125W ESD Susceptibility (Note 4) 3000V Junction Temperature (Note 5) 150 C
l a lVb l (No Signal)
b
94V
1C W 43 C W 2)
Operating Ratings (Notes 1
Temperature Range TMIN s TA s TMAX a b Supply Voltage lV l a lV l
b 20 C s TA s a 85 C
20V to 84V
Note Operation is guaranteed up to 84V however distortion may be introduced from SPiKe Protection Circuitry if proper thermal considerations are not taken into account Refer to the Thermal Considerations section for more information (See SPiKe TM Protection Response)
Electrical Characteristics (Notes 1 2) The following specifications apply for V IMUTE e b0 5 mA with RL e 4X unless otherwise specified Limits apply for TA e 25 C
Symbol Parameter
bt
a
e a 28V V b e b 28V
LM3886 Conditions Typical Limit (Note 6) (Note 7) 18 20 84 80
Units (Limits) V (min) V (max) dB (min)
lV a l a lVb l
AM
Power Supply Voltage (Note 10) Mute Attenuation
Vpin7 b V
9V
Pin 8 Open or at 0V Mute On Current out of Pin 8 l 0 5 mA Mute Off THD a N e 0 1% (max) f e 1 kHz f e 20 kHz lV a l e lVb l e 28V RL e 4X lV a l e lVb l e 28V RL e 8X lV a l e lVb l e 35V RL e 8X 60W RL e 4X 30W RL e 8X 20 Hz s f s 20 kHz AV e 26 dB
115
PO
Output Power (Continuous Average)
68 38 50 135 0 03 0 03
60 30
W (min) W (min) W W % %
Peak PO THD a N
Instantaneous Peak Output Power Total Harmonic Distortion Plus Noise
SR Ia VOS IB IOS Io Vod PSRR
Slew Rate (Note 9)
VIN e 2 0Vp-p tRISE e 2 ns
19 50 1 02 0 01 11 5 16 25 120 105
8 85 10 1 02 7 20 30 85 85
V ms (min) mA (max) mV (max) mA (max) mA (max) A (min) V (max) V (max) dB (min) dB (min)
Total Quiescent Power Supply Current VCM e 0V Vo e 0V Io e 0A Input Offset Voltage Input Bias Current Input Offset Current Output Current Limit Output Dropout Voltage (Note 11) Power Supply Rejection Ratio VCM e 0V Io e 0 mA VCM e 0V Io e 0 mA VCM e 0V Io e 0 mA
lV a l e lVb l e 20V tON e 10 ms VO e 0V a lV a Vb l Vb e 28V Io e a 100 mA O lVO V l V e b28V Io e b100 mA
V e 40V to 20V V e b40V VCM e 0V Io e 0 mA a b V e 40V V e b40V to b20V VCM e 0V Io e 0 mA
a b
DC Electrical Test refer to Test Circuit AC Electrical Test refer to Test Circuit
1 2
2
Electrical Characteristics (Notes 1 2) a b The following specifications apply for V e a 28V V e b28V IMUTE e b0 5 mA with RL e 4X unless otherwise specified Limits apply for TA e 25 C (Continued)
LM3886 Symbol Parameter Conditions
a b V e 60V to 20V V e b20V to b60V VCM e 20V to b20V Io e 0 mA
Typical (Note 6) 110 115 8 20 92 5 110 0 004 0 009
Limit (Note 7) 85 90 2 10
Units (Limits)
CMRR AVOL GBWP eIN SNR
Common Mode Rejection Ratio Open Loop Voltage Gain Gain-Bandwidth Product Input Noise Signal-to-Noise Ratio
dB (min) dB (min) MHz (min) mV (max) dB dB %
lV a l e lVb l e 28V lV a l e lVb l e 30V
RL e 2 kX DVO e 40V
fO e 100 kHz VIN e 50 mVrms IHF A Weighting Filter RIN e 600X (Input Referred) PO e 1W A-Weighted Measured at 1 kHz RS e 25X PO e 60W A-Weighted Measured at 1 kHz RS e 25X IMD Intermodulation Distortion Test
1 2
60 Hz 7 kHz 4 1 (SMPTE) 60 Hz 7 kHz 1 1 (SMPTE)
DC Electrical Test refer to Test Circuit AC Electrical Test refer to Test Circuit
Note 1 All voltages are measured with respect to the GND pin (pin 7) unless otherwise specified Note 2 Absolute Maximum Ratings indicate limits beyond which damage to the device may occur Operating Ratings indicate conditions for which the device is functional but do not guarantee specific performance limits Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits This assumes that the device is within the Operating Ratings Specifications are not guaranteed for parameters where no limit is given however the typical value is a good indication of device performance Note 3 For operating at case temperatures above 25 C the device must be derated based on a 150 C maximum junction temperature and a thermal resistance of iJC e 1 0 C W (junction to case) Refer to the Thermal Resistance figure in the Application Information section under Thermal Considerations Note 4 Human body model 100 pF discharged through a 1 5 kX resistor Note 5 The operating junction temperature maximum is 150 C however the instantaneous Safe Operating Area temperature is 250 C Note 6 Typicals are measured at 25 C and represent the parametric norm Note 7 Limits are guaranteed to National's AOQL (Average Outgoing Quality Level) Note 8 The LM3886T package TA11B is a non-isolated package setting the tab of the device and the heat sink at V potential when the LM3886 is directly mounted to the heat sink using only thermal compound If a mica washer is used in addition to thermal compound iCS (case to sink) is increased but the heat sink b will be isolated from V Note 9 The feedback compensation network limits the bandwidth of the closed-loop response and so the slew rate will be reduced due to the high frequency rolloff Without feedback compensation the slew rate is typically larger Note 10 V
b b
must have at least b 9V at its pin with reference to ground in order for the under-voltage protection circuitry to be disabled
Note 11 The output dropout voltage is the supply voltage minus the clipping voltage Refer to the Clipping Voltage vs Supply Voltage graph in the Typical Performance Characteristics section Note 12 The Differential Input Voltage Absolute Maximum Rating is based on supply voltages of V a e a 40V and Vb e b 40V
3
Test Circuit
1
(DC Electrical Test Circuit)
TL H 11833 3
Test Circuit
2
(AC Electrical Test Circuit)
TL H 11833 4
4
Single Supply Application Circuit
TL H 11833 5
FIGURE 2 Typical Single Supply Audio Amplifier Application Circuit
Optional components dependent upon specific design requirements Refer to the External Components Description section for a component functional description
Equivalent Schematic (excluding active protection circuitry)
TL H 11833 6
5
External Components Description (Figures 1 and 2 )
Components 1 2 3 4 5 RIN RA CA C RB CC Ri Ci Rf1 Rf2 Functional Description Acts as a volume control by setting the voltage level allowed to the amplifier's input terminals Provides DC voltage biasing for the single supply operation and bias current for the positive input terminal Provides bias filtering Provides AC coupling at the input and output of the amplifier for single supply operation Prevents currents from entering the amplifier's non-inverting input which may be passed through to the load upon power-down of the system due to the low input impedance of the circuitry when the under-voltage circuitry is off This phenomenon occurs when the supply voltages are below 1 5V Reduces the gain (bandwidth of the amplifier) at high frequencies to avoid quasi-saturation oscillations of the output transistor The capacitor also suppresses external electromagnetic switching noise created from fluorescent lamps Inverting input resistance to provide AC Gain in conjunction with Rf1 Feedback capacitor Ensures unity gain at DC Also a low frequency pole (highpass roll-off) at fc e 1 (2qRi Ci) Feedback resistance to provide AC Gain in conjunction with Ri At higher frequencies feedback resistance works with Cf to provide lower AC Gain in conjunction with Rf1 and Ri A high frequency pole (lowpass roll-off) exists at fc e Rf1 Rf2 (s a 1 Rf2Cf) (Rf1 a Rf2)(s a 1 Cf(Rf1 a Rf2)) Compensation capacitor that works with Rf1 and Rf2 to reduce the AC Gain at higher frequencies Mute resistance set up to allow 0 5 mA to be drawn from pin 8 to turn the muting function off x RM is calculated using RM s (lVEEl b 2 6V) I8 where I8 t 0 5 mA Refer to the Mute Attenuation vs Mute Current curves in the Typical Performance Characteristics section Mute capacitance set up to create a large time constant for turn-on and turn-off muting Works with CSN to stabilize the output stage by creating a pole that eliminates high frequency oscillations Works with RSN to stabilize the output stage by creating a pole that eliminates high frequency oscillations fc e 1 (2qRSNCSN) Provides high impedance at high frequecies so that R may decouple a highly capacitive load and reduce the Q of the series resonant circuit due to capacitive load Also provides a low impedance at low frequencies to short out R and pass audio signals to the load Provides power supply filtering and bypassing Mute switch that mutes the music going into the amplifier when opened
6
7 8 9 10
11 12
Cf RM
13 14 15
CM RSN CSN
16 17 18 19
L R CS S1
Optional components dependent upon specific design requirements Refer to the Application Information section for more information
OPTIONAL EXTERNAL COMPONENT INTERACTION Although the optional external components have specific desired functions that are designed to reduce the bandwidth and eliminate unwanted high frequency oscillations they may cause certain undesirable effects when they interact Interaction may occur for components whose reactances are in close proximity to one another One example would be the coupling capacitor CC and the compensation capacitor Cf These two components act as low impedances to certain frequencies which will couple signals from the input to the output Please take careful note of basic amplifier component functionality when designing in these components The optional external components shown in Figure 2 and described above are applicable in both single and split voltage supply configurations
6
Typical Performance Characteristics
Safe Area SPiKe Protection Response Supply Current vs Supply Voltage
Pulse Thermal Resistance
Pulse Thermal Resistance
Supply Current vs Output Voltage
Pulse Power Limit
Pulse Power Limit
Supply Current vs Case Temperature
Input Bias Current vs Case Temperature
Clipping Voltage vs Supply Voltage
Clipping Voltage vs Supply Voltage
TL H 11833 7
7
Typical Performance Characteristics
THD a N vs Frequency
(Continued)
THD a N vs Frequency
THD a N vs Frequency
THD a N vs Output Power
THD a N vs Output Power
THD a N vs Output Power
THD a N vs Output Power
THD a N vs Output Power
THD a N vs Output Power
THD a N vs Output Power
THD a N vs Output Power
THD a N vs Output Power
TL H 11833 17
8
Typical Performance Characteristics
THD a N Distribution
(Continued) THD a N Distribution
THD a N Distribution
THD a N Distribution
THD a N Distribution
Output Power vs Load Resistance
TL H 11833 8
Max Heatsink Thermal Resistance ( C W) at the Specified Ambient Temperature ( C)
Maximum Power Dissipation vs Supply Voltage
Note The maximum heat sink thermal resistance values O SA in the table above were calculated using a O CS e 0 2 C W due to thermal compound
TL H 11833 9
Power Dissipation vs Output Power
Power Dissipation vs Output Power
Output Power vs Supply Voltage
TL H 11833 10
9
Typical Performance Characteristics
IMD 60 Hz 4 1
(Continued) IMD 60 Hz 7 kHz 4 1
IMD 60 Hz 7 kHz 4 1
IMD 60 Hz 1 1
IMD 60 Hz 7 kHz 1 1
IMD 60 Hz 7 kHz 1 1
Mute Attenuation vs Mute Current
Mute Attenuation vs Mute Current
Large Signal Response
Power Supply Rejection Ratio
Common-Mode Rejection Ratio
Open Loop Frequency Response
TL H 11833 11
10
Application Information
GENERAL FEATURES Mute Function The muting function of the LM3886 allows the user to mute the music going into the amplifier by drawing less than 0 5 mA out of pin 8 of the device This is accomplished as shown in the Typical Application Circuit where the resistor RM is chosen with reference to your negative supply voltage and is used in conjuction with a switch The switch (when opened) cuts off the current flow from b pin 8 to V thus placing the LM3886 into mute mode Refer to the Mute Attenuation vs Mute Current curves in the Typical Performance Characteristics section for values of attenuation per current out of pin 8 The resistance RM is calculated by the following equation RM (lVEEl b 2 6V) I8 where I8 t 0 5 mA Under-Voltage Protection Upon system power-up the under-voltage protection circuitry allows the power supplies and their corresponding caps to come up close to their full values before turning on the LM3886 such that no DC output spikes occur Upon turn-off the output of the LM3886 is brought to ground before the power supplies such that no transients occur at power-down Over-Voltage Protection The LM3886 contains overvoltage protection circuitry that limits the output current to approximately 11Apeak while also providing voltage clamping though not through internal clamping diodes The clamping effect is quite the same however the output transistors are designed to work alternately by sinking large current spikes SPiKe Protection The LM3886 is protected from instantaneous peak-temperature stressing by the power transistor array The Safe Operating Area graph in the Typical Performance Characteristics section shows the area of device operation where the SPiKe Protection Circuitry is not enabled The waveform to the right of the SOA graph exemplifies how the dynamic protection will cause waveform distortion when enabled Thermal Protection The LM3886 has a sophisticated thermal protection scheme to prevent long-term thermal stress to the device When the temperature on the die reaches 165 C the LM3886 shuts down It starts operating again when the die temperature drops to about 155 C but if the temperature again begins to rise shutdown will occur again at 165 C Therefore the device is allowed to heat up to a relatively high temperature if the fault condition is temporary but a sustained fault will cause the device to cycle in a Schmitt Trigger fashion between the thermal shutdown temperature limits of 165 C and 155 C This greatly reduces the stress imposed on the IC by thermal cycling which in turn improves its reliability under sustained fault conditions Since the die temperature is directly dependent upon the heat sink the heat sink should be chosen as discussed in the Thermal Considerations section such that thermal shutdown will not be reached during normal operation Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor device THERMAL CONSIDERATIONS Heat Sinking The choice of a heat sink for a high-power audio amplifier is made entirely to keep the die temperature at a level such that the thermal protection circuitry does not operate under normal circumstances The heat sink should be chosen to dissipate the maximum IC power for a given supply voltage and rated load With high-power pulses of longer duration than 100 ms the case temperature will heat up drastically without the use of a heat sink Therefore the case temperature as measured at the center of the package bottom is entirely dependent on heat sink design and the mounting of the IC to the heat sink For the design of a heat sink for your audio amplifier application refer to the Determining The Correct Heat Sink section Since a semiconductor manufacturer has no control over which heat sink is used in a particular amplifier design we can only inform the system designer of the parameters and the method needed in the determination of a heat sink With this in mind the system designer must choose his supply voltages a rated load a desired output power level and know the ambient temperature surrounding the device These parameters are in addition to knowing the maximum junction temperature and the thermal resistance of the IC both of which are provided by National Semiconductor As a benefit to the system designer we have provided Maximum Power Dissipation vs Supply Voltages curves for various loads in the Typical Performance Characteristics section giving an accurate figure for the maximum thermal resistance required for a particular amplifier design This data was based on iJC e 1 C W and iCS e 0 2 C W We also provide a section regarding heat sink determination for any audio amplifier design where iCS may be a different value It should be noted that the idea behind dissipating the maximum power within the IC is to provide the device with a low resistance to convection heat transfer such as a heat sink Therefore it is necessary for the system designer to be conservative in his heat sink calculations As a rule the lower the thermal resistance of the heat sink the higher the amount of power that may be dissipated This is of course guided by the cost and size requirements of the system Convection cooling heat sinks are available commercially and their manufacturers should be consulted for ratings Proper mounting of the IC is required to minimize the thermal drop between the package and the heat sink The heat sink must also have enough metal under the package to conduct heat from the center of the package bottom to the fins without excessive temperature drop
11
Application Information (Continued)
A thermal grease such as Wakefield type 120 or Thermalloy Thermacote should be used when mounting the package to the heat sink Without this compound thermal resistance will be no better than 0 5 C W and probably much worse With the compound thermal resistance will be 0 2 C W or less assuming under 0 005 inch combined flatness runout for the package and heat sink Proper torquing of the mounting bolts is important and can be determined from heat sink manufacturer's specification sheets b Should it be necessary to isolate V from the heat sink an insulating washer is required Hard washers like beryluum oxide anodized aluminum and mica require the use of thermal compound on both faces Two-mil mica washers are most common giving about 0 4 C W interface resistance with the compound Silicone-rubber washers are also available A 0 5 C W thermal resistance is claimed without thermal compound Experience has shown that these rubber washers deteriorate and must be replaced should the IC be dismounted Determining Maximum Power Dissipation Power dissipation within the integrated circuit package is a very important parameter requiring a thorough understanding if optimum power output is to be obtained An incorrect maximum power dissipation (PD) calculation may result in inadequate heat sinking causing thermal shutdown circuitry to operate and limit the output power The following equations can be used to acccurately calculate the maximum and average integrated circuit power dissipation for your amplifier design given the supply voltage rated load and output power These equations can be directly applied to the Power Dissipation vs Output Power curves in the Typical Performance Characteristics section Equation (1) exemplifies the maximum power dissipation of the IC and equations (2) and (3) exemplify the average IC power dissipation expressed in different forms PDMAX e VCC2 2q2RL (1) where VCC is the total supply voltage (2) PDAVE e (VOpk RL) VCC q b VOpk 2 where VCC is the total supply voltage and VOpk e VCC q PDAVE e VCC VOpk qRL b VOpk2 2RL (3) where VCC is the total supply voltage Determining the Correct Heat Sink Once the maximum IC power dissipation is known for a given supply voltage rated load and the desired rated output power the maximum thermal resistance (in C W) of a heat sink can be calculated This calculation is made using equation (4) and is based on the fact that thermal heat flow parameters are analogous to electrical current flow properties It is also known that typically the thermal resistance iJC (junction to case) of the LM3886 is 1 C W and that using Thermalloy Thermacote thermal compound provides a thermal resistance iCS (case to heat sink) of about 0 2 C W as explained in the Heat Sinking section Referring to the figure below it is seen that the thermal resistance from the die (junction) to the outside air (ambient) is a combination of three thermal resistances two of which are known iJC and iCS Since convection heat flow (power dissipation) is analogous to current flow thermal resistance is analogous to electrical resistance and temperature drops are analogous to voltage drops the power dissipation out of the LM3886 is equal to the following PDMAX e (TJmax b TAmb) iJA where iJA e iJC a iCS a iSA
TL H 11833 12
But since we know PDMAX iJC and iSC for the application and we are looking for iSA we have the following iSA e (TJmax b TAmb) b PDMAX (iJC a iCS) PDMAX (4) Again it must be noted that the value of iSA is dependent upon the system designer's amplifier application and its corresponding parameters as described previously If the ambient temperature that the audio amplifier is to be working under is higher than the normal 25 C then the thermal resistance for the heat sink given all other things are equal will need to be smaller Equations (1) and (4) are the only equations needed in the determination of the maximum heat sink thermal resistance This is of course given that the system designer knows the required supply voltages to drive his rated load at a particular power output level and the parameters provided by the semiconductor manufacturer These parameters are the junction to case thermal resistance iJC TJmax e 150 C and the recommended Thermalloy Thermacote thermal compound resistance iCS
12
Application Information (Continued)
SIGNAL-TO-NOISE RATIO In the measurement of the signal-to-noise ratio misinterpretations of the numbers actually measured are common One amplifier may sound much quieter than another but due to improper testing techniques they appear equal in measurements This is often the case when comparing integrated circuit designs to discrete amplifier designs Discrete transistor amps often ``run out of gain'' at high frequencies and therefore have small bandwidths to noise as indicated below Typical signal-to-noise figures are listed for an A-weighted filter which is commonly used in the measurement of noise The shape of all weighting filters is similar with the peak of the curve usually occurring in the 3 kHz 7 kHz region as shown below
TL H 11833 14
TL H 11833 13
Integrated circuits have additional open loop gain allowing additional feedback loop gain in order to lower harmonic distortion and improve frequency response It is this additional bandwidth that can lead to erroneous signal-to-noise measurements if not considered during the measurement process In the typical example above the difference in bandwidth appears small on a log scale but the factor of 10 in bandwidth (200 kHz to 2 MHz) can result in a 10 dB theoretical difference in the signal-to-noise ratio (white noise is proportional to the square root of the bandwidth in a system) In comparing audio amplifiers it is necessary to measure the magnitude of noise in the audible bandwidth by using a ``weighting'' filter 1 A ``weighting'' filter alters the frequency response in order to compensate for the average human ear's sensitivity to the frequency spectra The weighting filters at the same time provide the bandwidth limiting as discussed in the previous paragraph In addition to noise filtering differing meter types give different noise readings Meter responses include 1 RMS reading 2 average responding 3 peak reading and 4 quasi peak reading Although theoretical noise analysis is derived using true RMS based calculations most actual measurements are taken with ARM (Average Responding Meter) test equipment Reference 1 CCIR ARM A Practical Noise Measurement Method by Ray Dolby David Robinson and Kenneth Gundry AES Preprint No 1353 (F-3)
SUPPLY BYPASSING The LM3886 has excellent power supply rejection and does not require a regulated supply However to eliminate possible oscillations all op amps and power op amps should have their supply leads bypassed with low-inductance capacitors having short leads and located close to the package terminals Inadequate power supply bypassing will manifest itself by a low frequency oscillation known as ``motorboating'' or by high frequency instabilities These instabilities can be eliminated through multiple bypassing utilizing a large tantalum or electrolytic capacitor (10 mF or larger) which is used to absorb low frequency variations and a small ceramic capacitor (0 1 mF) to prevent any high frequency feedback through the power supply lines If adequate bypassing is not provided the current in the supply leads which is a rectified component of the load current may be fed back into internal circuitry This signal causes low distortion at high frequencies requiring that the supplies be bypassed at the package terminals with an electrolytic capacitor of 470 mF or more LEAD INDUCTANCE Power op amps are sensitive to inductance in the output lead particularly with heavy capacitive loading Feedback to the input should be taken directly from the output terminal minimizing common inductance with the load Lead inductance can also cause voltage surges on the supplies With long leads to the power supply energy is stored in the lead inductance when the output is shorted This energy can be dumped back into the supply bypass capacitors when the short is removed The magnitude of this transient is reduced by increasing the size of the bypass capacitor near the IC With at least a 20 mF local bypass these voltage surges are important only if the lead length exceeds a couple feet ( l1 mH lead inductance) Twisting together the supply and ground leads minimizes the effect
13
Application Information (Continued)
LAYOUT GROUND LOOPS AND STABILITY The LM3886 is designed to be stable when operated at a closed-loop gain of 10 or greater but as with any other highcurrent amplifier the LM3886 can be made to oscillate under certain conditions These usually involve printed circuit board layout or output input coupling When designing a layout it is important to return the load ground the output compensation ground and the low level (feedback and input) grounds to the circuit board common ground point through separate paths Otherwise large currents flowing along a ground conductor will generate voltages on the conductor which can effectively act as signals at the input resulting in high frequency oscillation or excessive distortion It is advisable to keep the output compensation components and the 0 1 mF supply decoupling capacitors as close as possible to the LM3886 to reduce the effects of PCB trace resistance and inductance For the same reason the ground return paths should be as short as possible In general with fast high-current circuitry all sorts of problems can arise from improper grounding which again can be avoided by returning all grounds separately to a common point Without isolating the ground signals and returning the grounds to a common point ground loops may occur ``Ground Loop'' is the term used to describe situations occurring in ground systems where a difference in potential exists between two ground points Ideally a ground is a ground but unfortunately in order for this to be true ground conductors with zero resistance are necessary Since real world ground leads possess finite resistance currents running through them will cause finite voltage drops to exist If two ground return lines tie into the same path at different points there will be a voltage drop between them The first figure below shows a common ground example where the positive input ground and the load ground are returned to the supply ground point via the same wire The addition of the finite wire resistance R2 results in a voltage difference between the two points as shown below The load current IL will be much larger than input bias current II thus V1 will follow the output voltage directly i e in phase Therefore the voltage appearing at the non-inverting input is effectively positive feedback and the circuit may oscillate If there were only one device to worry about then the values of R1 and R2 would probably be small enough to be ignored however several devices normally comprise a total system Any ground return of a separate device whose output is in phase can feedback in a similar manner and cause instabilities Out of phase ground loops also are troublesome causing unexpected gain and phase errors The solution to most ground loop problems is to always use a single-point ground system although this is sometimes impractical The third figure below is an example of a singlepoint ground system The single-point ground concept should be applied rigorously to all components and all circuits when possible Violations of single-point grounding are most common among printed circuit board designs since the circuit is surrounded by large ground areas which invite the temptation to run a device to the closest ground spot As a final rule make all ground returns low resistance and low inductance by using large wire and wide traces Occasionally current in the output leads (which function as antennas) can be coupled through the air to the amplifier input resulting in high-frequency oscillation This normally happens when the source impedance is high or the input leads are long The problem can be eliminated by placing a small capacitor CC (on the order of 50 pF to 500 pF) across the LM3886 input terminals Refer to the External Components Description section relating to component interaction with Cf REACTIVE LOADING It is hard for most power amplifiers to drive highly capacitive loads very effectively and normally results in oscillations or ringing on the square wave response If the output of the LM3886 is connected directly to a capacitor with no series resistance the square wave response will exhibit ringing if the capacitance is greater than about 0 2 mF If highly capacitive loads are expected due to long speaker cables a method commonly employed to protect amplifiers from low impedances at high frequencies is to couple to the load through a 10X resistor in parallel with a 0 7 mH inductor The inductor-resistor combination as shown in the Typical Application Circuit isolates the feedback amplifier from the load by providing high output impedance at high frequencies thus allowing the 10X resistor to decouple the capacitive load and reduce the Q of the series resonant circuit The LR combination also provides low output impedance at low frequencies thus shorting out the 10X resistor and allowing the amplifier to drive the series RC load (large capacitive load due to long speaker cables) directly
TL H 1183315
14
Application Information (Continued)
GENERALIZED AUDIO POWER AMPLIFIER DESIGN The system designer usually knows some of the following parameters when starting an audio amplifier design Desired Power Output Input Level Input Impedance Load Impedance Maximum Supply Voltage Bandwidth The power output and load impedance determine the power supply requirements however depending upon the application some system designers may be limited to certain maximum supply voltages If the designer does have a power supply limitation he should choose a practical load impedance which would allow the amplifier to provide the desired output power keeping in mind the current limiting capabilities of the device In any case the output signal swing and current are found from (where PO is the average output power) Vopeak e 02 RL PO (1) (2) Iopeak e 0(2 PO) RL To determine the maximum supply voltage the following parameters must be considered Add the dropout voltage (4V for LM3886) to the peak output swing Vopeak to get the supply rail value (i e g (Vopeak a Vod) at a current of Iopeak) The regulation of the supply determines the unloaded voltage usually about 15% higher Supply voltage will also rise 10% during high line conditions Therefore the maximum supply voltage is obtained from the following equation g (Vopeak a Vod)(1 a regulation)(1 1) (3) Max supplies The input sensitivity and the output power specs determine the minimum required gain as depicted below AV t(0PO RL ) (VIN) e Vorms Vinrms (4) Normally the gain is set between 20 and 200 for a 40W 8X audio amplifier this results in a sensitivity of 894 mV and 89 mV respectively Although higher gain amplifiers provide greater output power and dynamic headroom capabilities there are certain shortcomings that go along with the so called ``gain '' The input referred noise floor is increased and hence the SNR is worse With the increase in gain there is also a reduction of the power bandwidth which results in a decrease in feedback thus not allowing the amplifier to respond quickly enough to nonlinearities This decreased ability to respond to nonlinearities increases the THD a N specification The desired input impedance is set by RIN Very high values can cause board layout problems and DC offsets at the output The value for the feedback resistance Rf1 should be chosen to be a relatively large value (10 kX 100 kX) and the other feedback resistance Ri is calculated using standard op amp configuration gain equations Most audio amplifiers are designed from the non-inverting amplifier configuration DESIGN A 40W 4X AUDIO AMPLIFIER Given Power Output Load Impedance Input Level Input Impedance Bandwidth 40W 4X 1V(max) 100 kX 20 Hz 20 kHz g 0 25 dB
Equations (1) and (2) give Iopeak e 4 5A 40W 4X Vopeak e 17 9V Therefore the supply required is g 21 0V 4 5A With 15% regulation and high line the final supply voltage is g 26 6V using equation (3) At this point it is a good idea to check the Power Output vs Supply Voltage to ensure that the required output power is obtainable from the device while maintaining low THD a N It is also good to check the Power Dissipation vs Supply Voltage to ensure that the device can handle the internal power dissipation At the same time designing in a relatively practical sized heat sink with a low thermal resistance is also important Refer to Typical Performance Characteristics graphs and the Thermal Considerations section for more information The minimum gain from equation (4) is AV t 12 6 We select a gain of 13 (Non-Inverting Amplifier) resulting in a sensitivity of 973 mV Letting RIN equal 100 kX gives the required input impedance however this would eliminate the ``volume control'' unless an additional input impedance was placed in series with the 10 kX potentiometer that is depicted in Figure 1 Adding the additional 100 kX resistor would ensure the minumum required input impedance For low DC offsets at the output we let Rf1 e 100 kX Solving for Ri (Non-Inverting Amplifier) gives the following Ri e Rf1 (AV b 1) e 100k (13 b 1) e 8 3 kX use 8 2 kX The bandwidth requirement must be stated as a pole i e the 3 dB frequency Five times away from a pole gives 0 17 dB down which is better than the required 0 25 dB Therefore fL e 20 Hz 5 e 4 Hz fH e 20 kHz c 5 e 100 kHz At this point it is a good idea to ensure that the Gain-Bandwidth Product for the part will provide the designed gain out to the upper 3 dB point of 100 kHz This is why the minimum GBWP of the LM3886 is important GBWP t AV c f3 dB e 13 c 100 kHz e 1 3 MHz GBWP e 2 0 MHz (min) for the LM3886 Solving for the low frequency roll-off capacitor Ci we have Ci t 1 (2q Ri fL) e 4 85 mF use 4 7 mF
15
Definition of Terms
Input Offset Voltage The absolute value of the voltage which must be applied between the input terminals through two equal resistances to obtain zero output voltage and current Input Bias Current The absolute value of the average of the two input currents with the output voltage and current at zero Input Offset Current The absolute value of the difference in the two input currents with the output voltage and current at zero Input Common-Mode Voltage Range (or Input Voltage Range) The range of voltages on the input terminals for which the amplifier is operational Note that the specifications are not guaranteed over the full common-mode voltage range unless specifically stated Common-Mode Rejection The ratio of the input commonmode voltage range to the peak-to-peak change in input offset voltage over this range Power Supply Rejection The ratio of the change in input offset voltage to the change in power supply voltages producing it Quiescent Supply Current The current required from the power supply to operate the amplifier with no load and the output voltage and current at zero Slew Rate The internally limited rate of change in output voltage with a large amplitude step function applied to the input Class B Amplifier The most common type of audio power amplifier that consists of two output devices each of which conducts for 180 of the input cycle The LM3886 is a Quasi-AB type amplifier Crossover Distortion Distortion caused in the output stage of a class B amplifier It can result from inadequate bias current providing a dead zone where the output does not respond to the input as the input cycle goes through its zero crossing point Also for ICs an inadequate frequency response of the output PNP device can cause a turn-on delay giving crossover distortion on the negative going transition through zero crossing at the higher audio frequencies THD a N Total Harmonic Distortion plus Noise refers to the measurement technique in which the fundamental component is removed by a bandreject (notch) filter and all remaining energy is measured including harmonics and noise Signal-to-Noise Ratio The ratio of a system's output signal level to the system's output noise level obtained in the absence of a signal The output reference signal is either specified or measured at a specified distortion level Continuous Average Output Power The minimum sine wave continuous average power output in watts (or dBW) that can be delivered into the rated load over the rated bandwidth at the rated maximum total harmonic distortion Music Power A measurement of the peak output power capability of an amplifier with either a signal duration sufficiently short that the amplifier power supply does not sag during the measurement or when high quality external power supplies are used This measurement (an IHF standard) assumes that with normal music program material the amplifier power supplies will sag insignificantly Peak Power Most commonly referred to as the power output capability of an amplifier that can be delivered to the load specified by the part's maximum voltage swing Headroom The margin between an actual signal operating level (usually the power rating of the amplifier with particular supply voltages a rated load value and a rated THD a N figure) and the level just before clipping distortion occurs expressed in decibels Large Signal Voltage Gain The ratio of the output voltage swing to the differential input voltage required to drive the output from zero to either swing limit The output swing limit is the supply voltage less a specified quasi-saturation voltage A pulse of short enough duration to minimize thermal effects is used as a measurement signal Output-Current Limit The output current with a fixed output voltage and a large input overdrive The limiting current drops with time once SPiKe protection circuitry is activated Output Saturation Threshold (Clipping Point) The output swing limit for a specified input drive beyond that required for zero output It is measured with respect to the supply to which the output is swinging Output Resistance The ratio of the change in output voltage to the change in output current with the output around zero Power Dissipation Rating The power that can be dissipated for a specified time interval without activating the protection circuitry For time intervals in excess of 100 ms dissipation capability is determined by heat sinking of the IC package rather than by the IC itself Thermal Resistance The peak junction-temperature rise per unit of internal power dissipation (units in C W) above the case temperature as measured at the center of the package bottom The DC thermal resistance applies when one output transistor is operating continuously The AC thermal resistance applies with the output transistors conducting alternately at a high enough frequency that the peak capability of neither transistor is exceeded Power Bandwidth The power bandwidth of an audio amplifier is the frequency range over which the amplifier voltage gain does not fall below 0 707 of the flat band voltage gain specified for a given load and output power Power bandwidth also can be measured by the frequencies at which a specified level of distortion is obtained while the amplifier delivers a power output 3 dB below the rated output For example an amplifier rated at 60W with s 0 25% THD a N would make its power bandwidth measured as the difference between the upper and lower frequencies at which 0 25% distortion was obtained while the amplifier was delivering 30W Gain-Bandwidth Product The Gain-Bandwidth Product is a way of predicting the high-frequency usefulness of an op amp The Gain-Bandwidth Product is sometimes called the unity-gain frequency or unity-gain cross frequency because the open-loop gain characteristic passes through or crosses unity gain at this frequency Simply we have the following relationship ACL1 c f1 e ACL2 c f2 Assuming that at unity-gain (ACL1 e 1 or (0 dB)) fu e fi e GBWP then we have the following GBWP e ACL2 c f2 This says that once fu (GBWP) is known for an amplifier then the open-loop gain can be found at any frequency This is also an excellent equation to determine the 3 dB point of a closed-loop gain assuming that you know the GBWP of the device Refer to the diagram on the following page
16
Definition of Terms (Continued)
Biamplification The technique of splitting the audio frequency spectrum into two sections and using individual power amplifiers to drive a separate woofer and tweeter Crossover frequencies for the amplifiers usually vary between 500 Hz and 1600 Hz ``Biamping'' has the advantages of allowing smaller power amps to produce a given sound pressure level and reducing distortion effects prodused by overdrive in one part of the frequency spectrum affecting the other part CCIR ARM Literally International Radio Consultative Committee Average Responding Meter This refers to a weighted noise measurement for a Dolby B type noise reduction system A filter characteristic is used that gives a closer correlation of the measurement with the subjective annoyance of noise to the ear Measurements made with this filter cannot necessarily be related to unweighted noise measurements by some fixed conversion factor since the answers obtained will depend on the spectrum of the noise source S P L Sound Pressure Level usually measured with a microphone meter combination calibrated to a pressure level of 0 0002 mBars (approximately the threshold hearing level) S P L e 20 Log 10P 0 0002 dB where P is the R M S sound pressure in microbars (1 Bar e 1 atmosphere e 14 5 lb in2 e 194 dB S P L )
TL H 11833 16
Physical Dimensions inches (millimeters)
Order Number LM3886T NS Package Number TA11B 17
LM3886 Overture Audio Power Amplifier Series High-Performance 68W Audio Power Amplifier w Mute
Physical Dimensions inches (millimeters) (Continued)
Order Number LM3886TF NS Package Number TF11B
LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user
National Semiconductor Corporation 2900 Semiconductor Drive P O Box 58090 Santa Clara CA 95052-8090 Tel 1(800) 272-9959 TWX (910) 339-9240 National Semiconductor GmbH Livry-Gargan-Str 10 D-82256 F4urstenfeldbruck Germany Tel (81-41) 35-0 Telex 527649 Fax (81-41) 35-1 National Semiconductor Japan Ltd Sumitomo Chemical Engineering Center Bldg 7F 1-7-1 Nakase Mihama-Ku Chiba-City Ciba Prefecture 261 Tel (043) 299-2300 Fax (043) 299-2500
2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness
National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960
National Semiconductores Do Brazil Ltda Rue Deputado Lacorda Franco 120-3A Sao Paulo-SP Brazil 05418-000 Tel (55-11) 212-5066 Telex 391-1131931 NSBR BR Fax (55-11) 212-1181
National Semiconductor (Australia) Pty Ltd Building 16 Business Park Drive Monash Business Park Nottinghill Melbourne Victoria 3168 Australia Tel (3) 558-9999 Fax (3) 558-9998
National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications