Text preview for : DP15HS_DP17LS.pdf part of SAMSUNG 750S/550B SAMSUNG 750S/550B SERVICE MAUNAL
THIS DEVICE IS MADE IN TIANJIN, CHINA.
Back to : DP15HS_DP17LS.pdf | Home
COLOR MONITOR
DP15HS/HT DP17LS/LT
SERVICE
COLOR MONITOR
Manual
CONTENTS
1. Precautions 2. Product Specifications 3. Disassembly & Reassembly 4. Alignment & Adjustments 5. Troubleshooting 6. Exploded View & Parts List 7. Electrical Parts List 8. Block Diagram
EXIT
MENU
9. Wiring Diagram 10. Schematic Diagrams
Samsung Electronics Co., Ltd. May 1999 Printed in Korea Code No.: BH68-00129A
Copyright © 1999 by Samsung Electronics Co., Ltd. All rights reserved. This manual may not, in whole or in part, be copied, photocopied, reproduced, translated, or converted to any electronic or machine readable form without prior written permission of Samsung Electronics Co., Ltd. DP15H*/DP17L* Service Manual First edition May 1999. Printed in Korea.
Trademarks Samsung is a registered trademark and DP15H*/DP17L* and MacMaster Cable Adapter are trademarks of Samsung Electronics Co., Ltd. Macintosh, Centris, Quadra, Duo Dock, and Power Macintosh are trademarks of Apple Computer, Inc. All other trademarks are the property of their respective owners.
ii
DP15H*/DP17L*
1 Precautions
1-1 Safety Precautions
WARNINGS 1. For continued safety, do not attempt to modify the circuit board. 2. 3. Disconnect the AC power before servicing. When the chassis is operating, semiconductor heatsinks are potential shock hazards. 3. 2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during this test. Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unitÕs AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat the test.
(READING SHOULD NOT BE ABOVE 0.5mA)
1-1-1
Servicing the High Voltage VR and CRT :
WARNING:A high voltage VR replaced in the wrong direction may cause excessive X-ray emissions. Caution: When replacing the high voltage adjustment VR, it must be fixed by a soldering iron after it is properly set. 1. When servicing the high voltage system, remove the static charge by connecting a 10 kohm resistor in series with an insulated wire (such as a test probe) between the chassis and the anode lead. If the HV VR requires adjustment, (a) Replace the VR and adjust the high voltage to the specification. (b) Use a soldering iron to melt the adjustment cap on the HV VR to prevent any movement. When troubleshooting a monitor with excessively HV, avoid being unnecessarily close to the monitor. Do not operate the monitor for longer than is necessary to locate the cause of excessive voltage. High voltage should always be kept at the rated value, no higher. Only when high voltage is excessive are X-rays capable of penetrating the shell of the CRT, including the lead in glass material. Operation at high voltages may also cause failure of the CRT or high voltage circuitry. When the HV regulator is operating properly, there is no possibility of an X-ray problem. Make sure the HV does not exceed its specified value and that it is regulating correctly. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the CRT only with one that is the same or equivalent type as the original. Handle the CRT only when wearing shatterproof goggles and after completely discharging the high voltage anode. Do not lift the CRT by the neck. 4.
2.
3.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES
LEAKAGE CURRENT TESTER
4.
2-WIRE CORD
5.
ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
EARTH GROUND
Figure 1-1. Leakage Current Test Circuit
6.
1-1-4 Product Safety Notices
Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by ! on schematics and parts lists. A substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire and / or other hazards. Product safety is under review continuously and new instructions are issued whenever appropriate. Components identified by on schematics and parts lists must be sealed by a soldering iron after replacement and adjustment.
7.
8.
1-1-2
Fire and Shock Hazard :
Before returning the monitor to the user, perform the following safety checks: 1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the monitor.
DP15H*/DP17L*
1-1
1 Precautions
1-2 Servicing Precautions
WARNING1: First read the "Safety Precautions" section of this manual. If unforeseen circumstances create conflict between the servicing precautions and safety precautions, always follow the safety precautions. WARNING2: A high voltage VR replaced in the wrong direction may cause excessive X-ray emissions. WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.
1. 2. Servicing precautions are printed on the cabinet, and should be followed closely. Always unplug the unitÕs AC power cord from the AC power source before attempting to: (a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect all test components in parallel with an electrolytic capacitor. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the area around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500 V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the +B voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. Always connect a test instrumentÕs ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrumentÕs ground lead last.
6.
3.
4.
8.
1-3 Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some fieldeffect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1.
Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wriststrap device. To avoid a shock hazard, be sure to remove the wrist strap before applying power to the monitor. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of an electrostatic charge. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs. Use only a grounded-tip soldering iron to solder or desolder ESDs. Use only an anti-static solder removal device. Some solder removal devices not classified as Òanti-staticÓ can generate electrical charges sufficient to damage ESDs.
6.
Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
7.
2.
3.
4. 5.
8.
Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD. Indicates ESDs on the Schematic Diagram in this manual.
9.
1-2
DP15H*/DP17L*
2 Product Specifications
2-1 Specifications
Item Picture Tube: Description 15-Inch (38 cm): 13.8-inch (35 cm) viewable, 17-Inch (43 cm): 16-inch (40.6 cm) viewable, Full-square flat-face tube, 90° Deflection, Semi- tint, Non-glare, Invar shadow mask, Anti-static silica coating, 0.28 mm Dot pitch Horizontal : 30 kHz to 70 kHz (Automatic) Vertical : 50 Hz to 160 Hz (Automatic) Unlimited colors Horizontal : 1280 Dots Vertical : 1024 Lines
Scanning Frequency Display Colors Maximum Resolution Input Video Signal Input Sync Signal Maximum Pixel Clock rate Active Display Input Voltage Power Consumption Dimensions (W x D x H)
Analog, 0.7 Vp-p positive at 75 , internally terminated Separate Sync: TTL level positive/negative 110 MHz 15" ; Horizontal : 267 mm ± 4 mm, Vertical : 200.5 mm ± 4 mm 17" ; Horizontal : 306 mm ± 4 mm (4:3 ratio), Vertical : 230.5 mm ± 4 mm AC 90 to 264 Volts, 60 Hz or 50 Hz ± 3 Hz 80 Watt (max) : 15", 90 Watt (max) : 17" 15" : 14.25 x 15.11 x 15.11 Inches (362 x 384 x 384 mm) 17" : 16.22 x 16.54 x 16.36 Inches (412 x 420 x 415.5 mm) Carton ; 15" : 17.87 x 19.57 x 17.52 Inches (454 x 497 x 445 mm) 17" : 21.02 x 21.73 x 18.39 Inches (534 x 552 x 467 mm) 15" : 26.5 lbs (12.0 kg) / 31.5 lbs (14.3 kg) 17" : 33.1 lbs (15.0 kg) / 38.6 lbs (17.5 kg) Operating Temperature : 32°F to 104°F (0°C to 40°C) Humidity : 10 % to 80 % Storage Temperature : -4°F to 113°F (-20°C to 45°C) Humidity : 5 % to 95 % Unit ;
Weight (Net/Gross) Environmental Considerations
· Above models comply with SWEDAC (MPR II) recommendations for reduced electromagnetic fields. · Designs and specifications are subject to change without prior notice.
DP15H*/DP17L*
2-1
2 Product Specifications
2-2 Pin Assignments
Sync Type Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue N-C
Separate
Macintosh GND-R Red H/V Sync Sense 0 Green GND-G Sense 1 Reserved Blue Sense 2 GND V-Sync GND-B GND H-Sync
DDC Return GND-R GND-G GND-B N-C GND-Sync/Self-raster N-C DDC Data H-Sync V-Sync DDC Clock
5
15
Figure 2-1. Male Type
Figure 2-2. Male Type
2-2
DP15H*/DP17L*
2 Product Specifications
2-3 Timing Chart
This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1. Timing Chart Mode IBM VGA2/70 Hz VGA3/60 Hz 720 x 400 640 x 480 31.469 31.777 3.813 1.907 25.422 0.636 70.087 14.268 0.064 1.080 12.711 0.413 28.322 31.469 31.778 3.813 1.907 25.422 0.636 59.940 16.683 0.064 1.048 15.253 0.318 25.175 640/75 Hz 640 x 480 37.500 26.667 2.032 3.810 20.317 0.508 75.000 13.333 0.080 0.427 12.800 0.027 31.500 640/85 Hz 640 x 480 43.269 23.111 1.556 2.222 17.778 1.556 85.008 11.764 0.671 0.578 11.093 0.023 49.500 VESA 800/75 Hz 800 x 600 46.875 21.333 1.616 3.232 16.162 0.323 75.000 13.333 0.064 0.448 12.800 0.021 36.000 800/85 Hz 800 x 600 53.674 18.631 1.138 2.702 14.222 0.569 85.061 11.756 0.056 0.503 11.179 0.019 56.250 1024/75 Hz 1024 x 768 60.023 16.660 1.219 2.235 13.003 0.203 75.029 13.328 0.050 0.466 12.795 0.017 78.750 1024/85 Hz 1024 x 768 68.677 14.561 1.016 2.201 10.836 0.508 84.997 11.765 0.044 0.524 11.183 0.015 94.500
Timing fH (kHz) A µsec B µsec C µsec D µsec E µsec fV (Hz) O msec P msec Q msec R msec S msec Clock Frequency (MHz) Polarity H.Sync V.Sync Remark
Negative Positive Separate
Negative Negative Separate
Negative Negative Separate
Negative Negative Separate
Positive Positive Separate
Positive Positive Separate
Positive Positive Separate
Positive Positive Separate
Separate Sync
Horizontal
Video Video
CC
Vertical
Video Video DD E E
Q
Q
RR
S S
Sync Sync B B AA
Sync Sync
PP
O O
A : Line time total C : Back porch E : Front porch DP15H*/DP17L*
B : Horizontal sync width D : Active time
O : Frame time total Q : Back porch S : Front porch
P : Vertical sync width R : Active time
2-3
2 Product Specifications
Memo
2-4
DP15H*/DP17L*
4 Alignment and Adjustments
This section of the service manual explains how to make permanent adjustments to the monitor. Directions are given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig).
4-1 Adjustment Conditions
Caution: Changes made without the Softjig are saved only to the user mode settings. As such, the settings are not permanently stored and may be inadvertently deleted by the user.
4-1-1 Before Making Adjustments
4-1-1 (a) ORIENTATION When servicing, always face the monitor to the east. 4-1-1 (b) MAGNETIC FIELDS Whenever possible, use magnetic field isolation equipment such as a Helmholtz field to surround the monitor. If a Helmholtz field is not available, frequently degauss the unit under test. Caution: Other electrical equipment may cause external magnetic fields which may interfere with monitor performance. Use an external degaussing coil to limit magnetic build up on the monitor. If an external degaussing coil is not available, use the internal degaussing circuit. However, do not use the internal degaussing circuit more than once per 30 minutes. 4-1-1 (c) WARM-UP TIME The monitor must be on for 30 minutes before starting alignment. Warm-up time is especially critical in color temperature and white balance adjustments. 4-1-1 (d) SIGNAL Analog, 0.7 Vp-p positive at 75 ohm, internal termination Sync: Separate (TTL level negative/positive) 4-1-1 (e) SCANNING FREQUENCY Horizontal: 30 kHz to 70 kHz (Automatic) Vertical: 50 Hz to 160 Hz (Automatic) Unless otherwise specified, adjust at the 17Ó: 1024 x 768 mode (68 kHz/85 Hz), 15Ó: 800 x 600 mode (54 kHz/85 Hz) signals. Refer to Table 2-1 on page 2-3.
.4-1-2 Required Equipment The following equipment may be necessary for adjustment procedures: 4-1-2 (a) DISPLAY CONTROL ADJUSTMENT 1. Non-metallic (Ð) screwdriver: 1.5, 2.5, 3 mm 2. Non-metallic (+) screwdriver: 1.5, 2.5, 3 mm 3. Digital Multimeter (DMM), or Digital Voltmeter 4. Signal generator, or DM200 software 5. Software: Softjig or DM200 6. Interface Board Ver. 2.0 Code No. BH81-90001K 7. Parallel communications cable (25-pin to 25-pin); Code No. BH81-90001H 8. Signal cable (15-pin to 15-pin cable with additional 3-pin connector); Code No. BH81-90001J 9. 5 V DC adapter, not supplied 10. Personal computer Note: Softjig AssÕy (includes items 6, 7 and 9) Code No. BH81-90001L 4-1-2 (b) COLOR ADJUSTMENTS 1. All equipment listed in 4-1-2 (a), above 2. Color analyzer, or any luminance measurement equipment
DP15H*/DP17L*
4-1
4 Alignment and Adjustments
4-1-3 Connecting the SoftJig
Connect the monitor to the signal generator and/ or PC as illustrated in Figures 4-1 and 4-2. Note: The signal cable connector which includes the 3-wire cable must connect to the monitor. If you use Setup 2 (PC only, no signal generator) you can only make adjustments to the signal timing available on that computer system. To make corrections to all factory timings requires the use of an additional signal generator.
MONITOR INTERFACE BOARD VER. 2.0 5V DC ADAPTOR SIGNAL CABLE PARALLEL CABLE PC D-SUB CONNECTOR 3-WIRE CABLE
MONITOR INTERFACE BOARD VER. 2.0 5V DC ADAPTOR PARALLEL CABLE PC SIGNAL GENERATOR SIGNAL CABLE
Figure 4-2. Setup 2, Without Signal Generator
3-WIRE CABLE
Figure 4-1. Setup 1, With Signal Generator
4-2
DP15H*/DP17L*
4 Alignment and Adjustments
4-2 Display Control Adjustments
4-2-1 HIGH VOLTAGE ADJUSTMENT
Signal: 1024 x 768 (68 kHz/85 Hz) (17Ó) 800 x 600 (54 kHz/85 Hz) (15Ó) Display image: DonÕt care Contrast: Minimum Brightness: Minimum Limit: 26.5 kV ± 0.2 kV (17Ó) 25 kV ± 0.2 kV (15Ó) exception) 26.0 kV ± 0.2 kV for 17Ó SDD CRT that the DY type is DMX-1791AT Measure the hight voltage level at the anode cap. High voltage should be within the limit as above. If the high voltage needs adjustment use the following procedure. PROCEDURE 1. Turn the power off and disconnect the AC line cord from the power source. 2. Turn the power on after connecting high voltage Probe. 3. Using the jig, adjust the high voltage to the specification. * High Voltage Adjustment PROCEDURE using Softjig x Select matching model name in ÒModelÓ field. Select Ò @7: Zero BeamÓ in menu after selecting ÒExtra 1Ó Adjust high voltage using control bar after selecting ÒHV MINÓ Turn the power off/on after adjustment finished. Check the high voltage has been fixed with adjusted value after reselecting Ò@7: Zero BeamÓ. Table 4-1
CRT type M41QAR361X11*(*) M41QAQ261X11*(*) M41LFQ903X28(L), etc M41EHN325X160/3F**U M41EHN323X160/3F**U M41LLJ507XX43*(F5), (F5W3) M41LLH507XX43*(F5) M36QAM351X11*(*) M36LGE128X2**(*) M36KUK35X02(*/LP), etc Screen Voltage 480V ± 10V 500V ± 10V 630V ± 10V 560V ± 10V 600V ± 10V 520V ± 10V
17"
15"
4-2-3 CENTER RASTER
Adjust SW401 so that the back raster comes to the center when you apply each basic mode for 15Ó and 17Ó.
4-2-4 Centering
Centering means to position the center point of the display in the middle of the display area. Horizontal size and position and vertical size and position control the centering of the display. Adjust the horizontal size and vertical size to their optimal settings: 306 mm (H) x 230 mm (V) for 17Ó, 267 mm (H) x 200 mm (V) for 15Ó. Adjust the horizontal position and vertical position to ² 4.0 mm of the center point of the screen. |A-B| ² 4.0 mm.
C DISPLAY AREA A B EDGE OF BEZEL D
|C-D| ² 4.0 mm.
4-2-2 SCREEN VOLTAGE ADJUSTMENT
CONDITIONS Signal: Display image: Contrast: Brightness: Limit: 1024 x 768 (68 kHz/85 Hz) (17Ó) 800 x 600 (54 kHz/85 Hz) (15Ó) DonÕt care Minimum Minimum 26.5 kV ± 0.2 kV (17Ó) 25 kV ± 0.2 kV (15Ó)
Figure 4-3. Centering * In Softjig window, ÒGeometryÓ has to be selected for GD adjustment. 4-2-4 (a) HORIZONTAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern Maximum Maximum
Screen Voltage adjustment procedure using softjig is all the same as 4-2-1 but selecting ÒG2 CONTÓ on the contrary to ÒHV MINÓ.
DP15H*/DP17L*
4-3
4 Alignment and Adjustments Use control bar after selecting ÒH-SIZEÓ in left menu to adjust the horizontal size of the display pattern to 306 mm (17Ó) and 267 mm (15Ó). (Tolerance: ± 3 mm.) If ÒH-SIZEÓ is not enough to adjust it, select ÒSIZE B+Ó by turns. 4-2-4 (b) VERTICAL SIZE ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern Maximum Maximum
4:3
Table 4-2. Standard Modes Linearity: 640x480/75Hz, 800x600/85Hz and 1024x768/85Hz Figure 4-5. Pinbalance
Standard Modes Linearity Each block (10 %) Difference between adjacent blocks (4 %)
Horizontal: 18.2~20.1 Horizontal: Less than 0.77 mm Vertical : 18.2~20.1 Vertical : Less than 0.77 mm Horizontal: 17.1~18.9 Horizontal: Less than 0.72 mm Vertical : 18.2~20.1 Vertical : Less than 0.77 mm
5:4
Table 4-3. Other Modes Linearity: VGA, SVGA, XGA, MAC, etc.
Supported Timing Mode Each block (10 %) 4:3 Horizontal: 17.8~20.5 Vertical : 17.8~20.5 Horizontal: 16.7~19.2 Vertical : 17.8~20.5 Difference between adjacent blocks (5 %) Horizontal: Less than 0.96 mm Vertical : Less than 0.96 mm Horizontal: Less than 0.90 mm Vertical : Less than 0.96 mm
Use control bar after selecting ÒV-SIZEÓ in left menu to adjust the vertical size of the display pattern to 230 mm (17Ó) and 200 mm (15Ó). (Tolerance: ± 3 mm.) 4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern
5:4
Use control bar after selecting ÒH-POSITIONÓ in left menu to center the horizontal image on the raster. 4-2-4 (d) VERTICAL POSITION ADJUSTMENT CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern
Use control bar after selecting ÒV-POSITIONÓ in left menu to center the vertical image on the raster.
4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Horizontal Linearity, refer to Tables 4-2 and 4-3 for the tolerance range. Increase or decrease H_LIN to optimize the image. 4-2-5 (b) VERTICAL LINEARITY ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Display image: Crosshatch pattern Brightness: Maximum Contrast: Maximum To adjust the Vertical Linearity, refer to Tables 4-2 and 4-3 for the tolerance range. Use control bar after selecting ÒV-LINEARITY BALÓ in left menu to optimize the image.
4-2-5 Linearity
Linearity affects the symmetry of images as they appear on the screen. Unless each row or column of blocks in a crosshatch pattern is of equal size, or within the tolerances shown in Tables 4-2 and 4-3, an image appears distorted, elongated or squashed.
4-4
DP15H*/DP17L*
4 Alignment and Adjustments
4-2-6 Trapezoid Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern Maximum Maximum
4-2-9 Side Pincushion Adjustment
CONDITIONS Scanning frequency: Display image: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern
Use control bar after selecting ÒTRAPEZOIDÓ in left menu to make the image area rectangular.
| A - B | < 4 mm A A
Use control bar after selecting ÒPINCUSHIONÓ in left menu to straighten the sides of the image area.
| C1 |, | C2 | 2.0 mm, | D1 |, | D2 | 2.0 mm. C2
D1 B B
D2
Figure 4-4. Trapezoid
C1
4-2-7 Pinbalance Adjustment
CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern Maximum Maximum
Figure 4-7. Pincushion
4-2-10 Tilt Adjustment
CONDITIONS Scanning Frequency: Display image: Brightness: Contrast:
D1
68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern Maximum Maximum
D1
D2
Use control bar after selecting ÒROTATIONÓ in left menu to correct the tilt of the display.
Figure 4-5. Pinbalance Use control bar after selecting ÒPINBALANCEÓ in left menu to optimize the image.
4-2-11 Degauss
No adjustments are available for the degaussing circuit. The degaussing circuit can effectively function only once per 30 minutes.
4-2-8 Parallelogram Adjustment
CONDITIONS Scanning Frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Crosshatch pattern Maximum Maximum
4-2-12 To Delete the User Mode Data
To delete the adjustment data from the user modes, click Ò@4: USER DELETEÓ in right ment.
4-2-13 Save the Data
To save the adjustment data for a mode, press Ò@3: ALL MODE SAVEÓ in right ment.
Use control bar after selecting ÒPARALLELÓ in left menu to make the image area rectangular.
4 mm
Figure 4-6. Parallelogram
DP15H*/DP17L*
4-5
4 Alignment and Adjustments
4-3 Color Adjustments
CAUTION:Check below condition before color adjustment Video signal : Analog 0.7 Vp-p (at 75 ) Sync : TTL level (H, V seperate signal) * Select ÒColorÓ in Softjig menu for color adjustment. 4-3-2 (b) WHITE BALANCE ADJUSTMENT CONDITIONS Scanning frequency: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Display image: White box pattern Brightness: 0.06ft-L at Back Raster Pattern Display Contrast: Maximum
1/3H-1/2H FRONT BEZEL OPENING 1/3V-1/2V BACK RASTER WHITE WINDOW
4-3-1 Color Coordinates (Temperature)
Color temperature is a measurement of the radiant energy transmitted by a color. For computer monitors, the color temperature refers to the radiant energy transmitted by white. Color coordinates are the X and Y coordinates on the chromaticity diagram of wavelengths for the visible spectrum. CONDITIONS Measurement instrument: Color analyzer Scanning frequency: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Display image: White flat field at center of display area Luminance: Maximum PROCEDURE Use the directions in sections 4-3-2 through 4-3-3 to adjust the color coordinates for: 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02 6500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02
Figure 4-8. White Box Pattern 1. Use control bar after selecting ÒRED GAINÓ, ÒGREEN GAINÓ and ÒBLUE GAINÓ to adjust the luminance to 45 ft-L (15Ó) and 46 ft-L (17Ó) with the color coordinates ranged for 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02. exception) 17Ó SDD CRT type-named (*/S-2) : 42ft-L. 4-3-2 (c) ABL ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Full white pattern Maximum Maximum
FRONT BEZEL OPENING BACK RASTER WHITE WINDOW
4-3-2 Color Adjustments for 9300K
4-3-2 (a) BACK RASTER COLOR ADJUSTMENT CONDITIONS Scanning frequency: Display image: Brightness: Contrast: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Back raster pattern Maximum Maximum
1. Select Ò@1: CHANNEL 1Ó in right menu to control the color for 9300K. 2. Adjust the luminance of the back raster to between 0.5 to 0.7 ft-L using contron bar after selecting ÒGREEN CUTOFFÓ in the menu. 3. Use control bar after selecting ÒBLUE CUTOFFÓ in left menu to set the ÒyÓ coordinate to 0.298 ± 0.02. 4. Use control bar after selecting ÒRED CUTOFFÓ in left menu to 0.283 ± 0.02. * If color values would not be matched desirable values, repeat sequence 3 and 4 after readjusting ÒGREEN CUTOFFÓ control a little different. 4-6
Figure 4-9. Full White Pattern 1. Check the ABL. If it is not within the specifications, use the ABL controls to adjust it. (15Ó: 33 ± 1 ft-L, 17Ó: 36 ± 1 ft-L ) 2. Select Ò@4: COLOR SAVEÓ to save the data. 3. Select Ò@6: ALL COLOR SAVEÓ to save the CH2.
DP15H*/DP17L*
4 Alignment and Adjustments 4-3-2 (d) WHITE BALANCE ADJUSTMENT VERIFICATION CONDITIONS Scanning frequency: Display image: X-Y Coordinates: ABL Luminance Brightness: Contrast: PROCEDURE Measure luminance at nine points on the display screen (see figure below).
68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) Back raster pattern Full White Pattern x = 0.283 ± 0.02, y = 0.298 ± 0.02 Refer to 4-3-2(c) Maximum 5 ft-L, 24 ft-L
Figure 4-10. Luminance Uniformity Check Locations
1. Check whether the color coordinates of the back raster satisfy the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. 2. Display a full white pattern. 3. Select ÒGeometryÓ in softjig menu. 4. Select Ò@7: 5-ft Ò in right menu. 5. Check whether the white coordinates of the video meet the above coordinates spec. 6. Select Ò@8: 24-ft Ò in right menu. 7. Check whether the white coordinates of the video satisfies the above spec. If they do not, return to 4-3-2 (a) and readjust all settings. Select ÒColorÓ and click Ò@2: CHANNEL 2Ó for color ajdustment for 6500K Repeat the sequence of 9300K adjustment. The luminance values the same as 9300K, but the color coordinated of back raster and white box are : x = 0.313 ± 0.02 y = 0.329 ± 0.02
4-3-4 Focus Adjustment
CONDITIONS Scanning frequency: 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) (1024 x 768) ÒHÓ character pattern Cut off point Maximum
Display image: Brightness: Contrast:
PROCEDURE 1. Adjust the Focus VR on the FBT to display the sharpest image possible. 2. Use Locktite to seal the Focus VR in position.
4-3-5 Color Purity Adjustment
Color purity is the absence of undesired color. Conspicuous mislanding (unexpected color in a uniform field) within the display area shall not be visible at a distance of 50 cm from the CRT surface. CONDITIONS Orientation: Scanning frequency: Display image: Luminance:
4-3-3 Luminance Uniformity Check
Luminance is considered uniform only if the ratio of lowest to highest brightness areas on the screen is not less than 7.5:10. CONDITIONS Scanning frequency:
Monitor facing east 68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) White flat field Cut off point at the center of the display area
Display image: Brightness: Contrast:
68 kHz/85 Hz (17Ó) 54 kHz/85 Hz (15Ó) (1024 x 768) White flat field Cut off point at 24 ft-L Maximum
Note: Color purity adjustments should only be attempted by qualified personnel.
DP15H*/DP17L*
4-7
4 Alignment and Adjustments PROCEDURE For trained and experienced service technicians only. Use the following procedure to correct minor color purity problems: 1. Make sure the display is not affected by external magnetic fields. 2. Very carefully break the glue seal between the 2-pole purity convergence magnets (PCM), the band and the spacer (see Figures 4-12). 3. Make sure the spacing between the PCM assembly and the CRT stem is 29 mm ± 1 mm. 4. Display a green pattern over the entire display area. 5. Adjust the purity magnet rings on the PCM assembly to display a pure green pattern. (Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015) 6. Repeat steps 4 and 5 using a red pattern and then again, using a blue pattern. Table 4-4. Color Purity Tolerances
Red: Green: Blue: x = 0.640 ± 0.015 x = 0.295 ± 0.015 x = 0.142 ± 0.015 y = 0.323 ± 0.015 y = 0.594 ± 0.015 y = 0.066 ± 0.015
(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)
7. When you have the PCMs properly adjusted, carefully glue them together to prevent their movement during shipping.
4-8
DP15H*/DP17L*
5 Troubleshooting
5-1 Parts Level Troubleshooting
Notes: 1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect. 2. Check the following circuits. · No raster appears: Power circuit, Horizontal output circuit. · High voltage develops but no raster appears: Video output circuits. · High voltage does not develop: Horizontal output circuits.
5-1-1 No Power Supply
Check and replace D601, FH1
WAVEFORMS
1 100 V (IC601, #1)
Chirping noise exists?
Yes
Check and replace IC601.
No Repeating start? Yes Check and replace D606.
CH1 P-P = 100 V
CH1 RMS = 350.2 V
No
1
IC601 Pin 1 waveform is right?
No
Check and replace D614, IC601, Q602, ZD601.
Yes C622 Voltage is 13 V ± 0.5V? No Check and replace IC201, IC301, IC401, Q402, Q404.
Yes Normal operation No Replace Main board.
Yes Verify voltages.
Yes Done.
DP15H*/DP17L*
5-1
5 Troubleshooting
5-1-2 DPMS Failure
Check signal source H/V sync video level.
WAVEFORMS
2 100V (IC601, #1)
Make No H/V sync (power off mode)
CH1 P-P = 100V CH1 RMS = 325.8 V
LED blinks
No
Check IC201 Pin 40.
Yes +12 V line off No Check IC201 Pin 5.
Yes IC602 Pin 4 voltage exists? No
2
Yes
Check IC201 Pin 6. Check and replace IC602.
IC601 Pin 1 output voltage exists? Yes Done
No
Refer to 5-1-1 No Power Supply.
5-2
DP15H*/DP17L*
5 Troubleshooting
5-1-3 H_Deflection Failure
Does PWM output signal appear at Pin 6 (H_out) of IC401? Yes No Does DC 12V appear at Pin 10 of IC401? Yes No Check 12 V line.
3
WAVEFORMS
Check IC401.
3 2.00 V (IC401, #6)
4
Does Horizontal paluse signal appear at at Pin 8 of IC401? Yes
No
Check IC401.
CH1 P-P = 2.00V CH1 RMS = 5.868V
4 1.00V (IC401, #8)
Does 110 Vp-p signal appear 5 at Collector of Q403? No Check Q402, Q404, T401.
No
Check Q443.
CH1 P-P = 1.00V
CH1 RMS = 1.298V
5 20.0 V (Q403, Collector)
7-1-4 S Correction Failure
Check S1 ~ S3 signal.
CH1 P-P = 20.0 V
CH1 RMS = 46.80V
S1~S3 signals are right at each frequency block? Yes Check and replace Q404, Q409, Q410, Q414, Q415, Q416
No
Check and replace IC201.
DP15H*/DP17L*
5-3
5 Troubleshooting
5-1-5 H_Lin. Failure
IC201 Pin 21 voltage varies with different H_Lin. DAC values? Yes IC603 Pin 9 voltage varies with different H_Lin. DAC values? Yes Check Q412, Q413, T402. No Check +12 V, 10 V line. Check some parts around IC603. No
Replace IC201.
5-1-6 Invariable H_Size
IC401 Pin 6 voltage varies with different B_Out DAC values? Yes Q402 Gate output duty varies with different B_Out DAC values? No Check some parts around Q402, IC401 Pin 3 ~ 6. No
Check and replace IC401.
5-1-7 Abnormal H_Size
IC401 Pin 11 output duty varies with different B+ offset DAC values? Yes
6
No
WAVEFORMS
Check and replace IC201.
6 200 V (Q408, Collector)
Q408 Collector waveform is right? Yes
No
Check and replace Q405, Q406, Q407, Q408.
CH1 P-P = 200V CH1 RMS = 387.2V
Check some parts around D409, L401.
5-4
DP15H*/DP17L*
5 Troubleshooting
5-1-8 Side Pin or Trap Failure
No
WAVEFORMS
Check and replace IC401.
7 1.00 V (IC401, #11)
7
IC401 Pin 11 output exists?
Yes Refer to 5-1-7 Abnormal H_Size.
CH1 P-P = 1.00V CH1 RMS = 3.008 V
5-1-9 Para. or Pin Balance Failure
IC401 Pin 11 output varies with different DAC values? No Replace IC401. Yes
Refer to 5-1-7 Abnormal H_Size.
5-1-10 Tilt Failure
Check tilt connector connection
IC201 Pin 20 output duty varies with different DAC values? Yes IC603 Pin 13 output varies with different DAC values? Yes Check and replace Q301, Q302.
No
Check and replace IC201.
No
Check and replace IC603.
DP15H*/DP17L*
5-5
5 Troubleshooting
5-1-11 V Deflection Failure
No
WAVEFORMS
Refer to 5-1-1 No Power Supply
8 500 V (IC401, #12)
13 V, 10 V line is on?
Yes
8
IC401 Pin 12 output exists?
No
Check and replace IC401.
CH1 P-P = 500 V CH1 RMS = 1.425 V
Yes
9
9 10.0 V (IC301, #6)
IC301 Pin 6 output exists?
No
Check and replace some parts around IC301.
Yes Check DY connector connection.
CH1 P-P = 10.0 V
CH1 RMS = 5.06 V
5-1-12 V Size or Pos. Variation Failure
IC401 Pin 12 output varies with different DAC values? Yes Check and replace IC301. No
Check and replace IC201, IC401.
5-6
DP15H*/DP17L*
5 Troubleshooting
5-1-13 High Voltage Failure
No
WAVEFORMS
Check and replace IC401 and +12 V line.
3 2.00 V (IC401, #6)
3
IC401 Pin 6 OSC pulse exists?
Yes
10
Q402 Gate driving pulse exists?
No
Check and replace Q401.
CH1 P-P = 2.00 V CH1 RMS = 5.868 V
Yes
11
11 2.00 V (Q402, Gate)
Q402 Drain pulse exists?
No
Check and replace Q403, L402.
Yes Done
CH1 P-P = 2.00 V
CH1 RMS = 7.692V
11 50.0 V (Q402, Drain)
5-1-14 ABL Failure
CH1 P-P = 50.0 V CH1 RMS = 73.7V
Input full white pattern to monitor.
IC101 Pin 12 input exists and varies with different patterns? No Check CN102. No T501 Pin 8 output exists?
Yes
Check and replace IC101.
No
Check and replace T501.
Yes IC201 Pin 26 output exists and varies with different patterns? Yes Done No Check and replace IC201.
DP15H*/DP17L*
5-7
5 Troubleshooting
5-1-15 Dynamic Focus Failure
IC401 Pin 32 output is right? No
WAVEFORMS
Replace the IC401.
12 2.00 V (IC401, #32)
12
Yes Some parts around Q551 are right? No Replace failed part.
CH1 P-P = 2.00V CH1 RMS = 6.124V
Yes
13
13 50.0 V (T502, #6)
T502 Pin 6 input is right?
No
Check and replace C432.
Yes
CH1 P-P = 50.0V CH1 RMS = 75.6V
14
T502 Pin 1 output is right?
No
Replace the T502.
14 100 V (T502, #1)
No Check the connection between FBT Focus pin, CRT Socket PCB.
CH1 P-P = 100V
CH1 RMS = 124.0V
5-8
DP15H*/DP17L*
5 Troubleshooting
5-1-16 No Video
Check signal cable and connection.
WAVEFORMS
15 1.00 V (IC101, #5, 8, 10)
15
IC101 Pins 5, 8 and 10 inputs are right? Yes
No
Check the signal cable connection.
CH1 P-P = 1.00V
CH1 RMS = 2.452V
16
IC101 Pins 21, 24 and 26 outputs are right? Yes
No
16 1.00 V (IC101, #21,24,26)
Check I2C bus and +12 V line.
17
IC103 Pins 1, 2 and 3 outputs are right? Yes Cathode DC levels are right?
No
Check +12 V, +72 V line. Check and replace IC103.
CH1 P-P = 1.00V
CH1 RMS = 2.792V
17 20.0 V (IC103, #1, 2, 3)
No
Check +72 V line. Check and replace QR01, QR02, QG01, QG02, QB01, QB02.
CH1 P-P = 20.0V CH1 RMS = 40.52V
Yes G2 voltage is right? No Check G2 wire, CRT Socket board, and FBT.
Yes Change CRT.
Done.
DP15H*/DP17L*
5-9
5 Troubleshooting
5-1-17 Micom Failure
No
WAVEFORMS
Check IC604.
18 1.00 V (IC201, #13, 14)
IC201 Pin 11 input voltage is 5V?
Yes
18
IC201 Pins 13 and 14 inputs are right? Yes IC201 Pin 18 input is right?
No
Check C202, C203, X201.
CH1 P-P = 1.00 V CH1 RMS = 2.108V
No
Check IC605.
Yes All in/output values are right? No Replace IC201.
No Done
5-10
DP15H*/DP17L*
5 Troubleshooting
5-1-18 OSD Failure
Check CN104 and connector Ass'y.
WAVEFORMS
19 1.00 V (IC104, #6)
19
IC104 Pin 6 input is right?
No
Check and replace Q102. Check CN102 Pin 14.
CH1 P-P = 1.00V CH1 RMS = 4.516V
Yes
20
IC104 Pin 17 input is right?
No
Check and replace Q101. Check CN102 Pin 8.
20 1.00 V (IC104, #17)
Yes IC104 Pins 7 and 8 inputs are right? Yes IC104 Pins 12, 13 and 14 outputs are right? No
21
No
Check IC201 Pins 41 and 42.
CH1 P-P = 1.00V
CH1 RMS = 5.024V
21 1.00 V (IC101, #21.24.26)
No
Check and replace IC104.
CH1 P-P = 1.00V CH1 RMS = 2.580V
IC101 Pins 21, 24 and 26 outputs are right? Yes Check and replace IC103.
No
Check and replace IC101.
Done
DP15H*/DP17L*
5-11
5 Troubleshooting
5-1-19 User Control Failure
Does the DC level change at Pin 36 of IC201 when you push the button S/W? Yes Check IC201. No Check the button. (SW201 ~ SW204)
5-1-20 Degaussing Failure
Check degaussing connector.
RL601 operation is right?
Yes
Check D-coil and TH601.
No Q601 base input is right? Yes Check and replace Q601.
No IC201 Pin 4 output is right? No Check and replace IC201.
Yes Done
5-12
DP15H*/DP17L*
5 Troubleshooting
5-2 General Troubleshooting
5-2-1 No Picture
Yes
LED blinks?
Refer to 5-2-2 Shut down.
No LED is green color? No Check Micom.
Yes Check G2 voltage, high voltage, R, G, B cathode voltage.
5-2-2 Shut Down
Blinking LED's?
No
Check power supply.
Yes Scan failure Yes Check horizontal, vertical deflection system and check power supply secondary voltages.
No Video failure? Yes Check Video board.
No Check and replace IC201.
Done
DP15H*/DP17L*
5-13
5 Troubleshooting
5-2-3 Missing Color WAVEFORMS
Are proper Video levels on CN101 (D-Sub) Pins 1, 3 and 5? Yes
22
No
Check signal generator.
22 10.0 V (R,G,B, Video)
Are proper Video signal on all cathodes? Yes Are proper DC voltage on all cathodes? Yes Is G2 voltage right? Yes Is Heater voltage right?
No
Refer to 5-1-16 No Video.
CH1 P-P = 10.0V
CH1 RMS = 17.02V
No
Check IC101 Pins 15, 16 and 17. Check QR01, QR02, QG01, QG02, QB01 and QB02.
No
Check D502, D503, Q501.
No
Check D608, Q604, T601.
Yes Is G1 voltage right? Yes Replace CRT. Yes Done No Check D504, Q602, T501.
5-14
DP15H*/DP17L*
5 Troubleshooting
5-2-4 Visible Retrace
Check white balance adjustment.
Is G2 voltage right?
No
Check D502, D503, Q501 and Adjust G2.
Yes Is blank pulse on Pin 17 of IC401? No Check IC401.
WAVEFORMS
Yes
23 23 5.00 V (Q303, Collector)
Is V_FLB pulse on Collector of Q303? Yes
No
Check Q303.
24
Does approve the Vertical pulse on the CRT Socket G1? Yes Done
No
CH1 P-P = 5.00V
CH1 RMS = 28.33V
Check CN102, CN201.
24 20.00 V (CRT, G1)
CH1 P-P = 20.0V
CH1 RMS = 66.68V
DP15H*/DP17L*
5-15
5 Troubleshooting
5-2-5 Unsynchronized Image
Check input signals Pins 2 and 3 of CN202.
Are signals right?
No
Check Video Cable
Yes Signals at Pins 28 and 29 of IC201 are right? Yes Signals at Pins 14 and 15 of IC401 are right? Yes Check circuits on Main board. No Check IC401 No Check IC201.
Done
5-16
DP15H*/DP17L*
5 Troubleshooting
5-2-6 Misconvergence
Try readjusting convergence.
Is the convergence now within spec? No Readjust convergence.
Yes
Done
Is the convergence now within spec? No Change CRT and readjust convergence.
Yes
Done
Done
DP15H*/DP17L*
5-17
5 Troubleshooting
5-2-7 Poor Focus
Adjust focus VR of FBT.
Improved focus?
Yes
Aging monitor and check for focus change.
No Check focus leads from FBT to CRT Socket.
Check the CRT Socket.
Is dynamic focus circuit right?
No
Refer to 5-1-15 Dynamic Focus Failure.
Yes Replace the CRT and verify focus.
5-2-8 Purity Failure
Degaussing
Purity is right?
Yes
Done
No Degaussing circuit is right? No Refer to 5-1-20 Degaussing Failure.
Yes Replace CRT and verify purity.
5-18
DP15H*/DP17L*
7 Electrical Parts List
7 Electrical Parts List
7-1 Main PCB Parts
Loc. No. BD301 BD401 BD402 BD402 BD601 BD602 BD603 C201 C202 C203 C204 C205 C206 C207 C209 C210 C211 C212 C213 C214 C215 C216 C217 C220 C301 C302 C305 C306 C307 C308 C309 C311 C312 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 Code No. 3301-000011 3301-000011 3301-000011 BH39-40305U 3301-000011 3301-000011 3301-000011 2401-000025 2201-000389 2201-000389 2401-002075 2401-000603 2401-000050 2401-002075 2401-002075 2401-002075 2201-000146 2201-000017 2401-000029 2401-000025 2201-000146 2401-000603 2202-002009 2401-000025 2301-000010 2305-000291 2401-000037 2401-000856 2305-000237 2301-000013 2202-002008 2301-001027 2401-001016 2301-000312 2201-000021 2301-000148 2301-000148 2201-000823 2301-000231 2401-000540 2201-000469 2306-000147 2401-000025 2301-000005 2301-000148 Description CORE-FERRITEBEAD CORE-FERRITEBEAD CORE-FERRITEBEAD CBF-HARNESS CORE-FERRITEBEAD CORE-FERRITEBEAD CORE-FERRITEBEAD C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-AL C-AL C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-CERAMIC,DISC C-AL C-CERAMIC,MLC-AXIAL C-AL C-FILM,PEF C-FILM,MPEF C-AL C-AL C-FILM,MPEF C-FILM,PEF C-CERAMIC,MLC-AXIAL C-FILM,PEF C-AL C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-FILM,PEF C-CERAMIC,DISC C-FILM,PEF C-AL C-CERAMIC,DISC C-FILM,MPPF C-AL C-FILM,PEF C-FILM,PEF Specification AA,3.5x1.0x5.7mm,1500 AA,3.5x1.0x5.7mm,1500 AA,3.5x1.0x5.7mm,1500 52MM,AWG22(0.6PI) AA,3.5x1.0x5.7mm,1500 AA,3.5x1.0x5.7mm,1500 AA,3.5x1.0x5.7mm,1500 100uF,20%,16V,GP,TP,6.3x11,5 22pF,5%,50V,CH,TP,5.0*3.0 22pF,5%,50V,CH,TP,5.0*3.0 4.7uF,20%,50V,GP,TP,5x11,5 1uF,20%,50V,GP,TP,5x11,5 10uF,20%,16V,GP,TP,5x11,2.5 4.7uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 4.7uF,20%,50V,GP,TP,5x11,5 100pF,5%,50V,SL,TP,5x3,5 1nF,10%,50V,Y5P,TP,4x3.5, 10uF,20%,100V,GP,TP,6.3x11,5 100uF,20%,16V,GP,TP,6.3x11,5 100pF,5%,50V,SL,TP,5x3,5 1uF,20%,50V,GP,TP,5x11,5 100nF,+80-20%,50V,Y5 100uF,20%,16V,GP,TP,6.3x11,5 100nF,5%,100V,TP,11.5x12.5mm 220nF,5%,63V,TP,7.5x13.5mm,5 470uF,20%,16V,GP,TP,8x11.5,5 220uF,20%,35V,WT,TP,10x20,5 1uF,5%,63V,TP,7.5x15.5mm,5mm 4.7nF,5%,100V,TP,10.5x12.5x6 10nF,+80-20%,50V,Y5V 15nF,10%,250V,TP,9.5x12x4.5,5 3.3UF,20%,50V,BP,TP,5X11,5 8.2nF,5%,100V,TP,6x12.5mm,5mm 100nF,+80-20%,50V,Y5V,TP 10nF,5%,100V,TP,7x3.2x7mm,5mm 10nF,5%,100V,TP,7x3.2x7mm,5mm 270pF,5%,50V,SL,TP,5x3,5 3.3nF,5%,100V,TP,5.8x12.5mm,5 150uF,20%,63V,LZ,TP,10x25,5 330pF,10%,500V,Y5P,TP,6x4 1uF,5%,250V,BK,26x24x15,22.5 100uF,20%,16V,GP,TP,6.3x11,5 33nF,5%,100V,TP,5.8x12.5x3,5 10nF,5%,100V,TP,7x3.2x7mm,5mm Remarks
17" 15"
DP15H*/DP17L*
7-1
7 Electrical Parts List
Loc. No. C413 C414 C415 C415 C416 C417 C419 C420 C420 C421 C423 C425 C425 C426 C427 C427 C429 C430 C431 C431 C432 C433 C434 C435 C436 C501 C502 C503 C504 C504 C505 C506 C507 C508 C509 C510 C511 C512 C513 C514 C515 C551 C552 C601 C602 C603
Code No. 2401-001012 2401-001334 2401-001218 2401-000043 2301-000010 2301-000148 2309-000106 2309-000107 2309-000106 2303-001029 2401-000603 2306-000119 2306-000131 2401-000603 2306-000164 2306-000179 2401-000603 2306-000249 2306-000179 2306-000171 2305-001033 2305-001003 2401-001016 2201-000469 2201-000012 2301-000016 2301-000016 2401-000050 2301-000004 2301-000004 2401-000059 2201-000019 2201-000291 2401-002267 2401-002267 2301-000005 2301-000231 2201-000020 2201-000291 2401-001334 2301-000148 2401-000050 2201-000132 2301-001195 2301-001195 2201-000023
Description C-AL C-AL C-AL C-AL C-FILM,PEF C-FILM,PEF C-FILM,MPE-PPF C-FILM,MPE-PPF C-FILM,MPE-PPF C-FILM,PPF C-AL C-FILM,MPPF C-FILM,MPPF C-AL C-FILM,MPPF C-FILM,MPPF C-AL C-FILM,MPPF C-FILM,MPPF C-FILM,MPPF C-FILM,MPEF C-FILM,MPEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-FILM,PEF C-FILM,PEF C-AL C-FILM,PEF C-FILM,PEF C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-AL C-FILM,PEF C-FILM,PEF C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-FILM,PEF C-AL C-CERAMIC,DISC C-FILM,MPPF C-FILM,MPPF C-CERAMIC,DISC
Specification 3.3UF,20%,50V,BP,TP,16X25,7.5 470nF,20%,50V,GP,TP,5x11,2.5 4.7uF,20%,100V,WT,TP,5x11,5 1uF,20%,160V,GP,TP,6.3x11,5 100nF,5%,100V,TP,11.5x12.5mm 10nF,5%,100V,TP,7x3.2x7mm,5mm 2.2nF,5%,1.6KV,TP,23x16x9 2.5nF,5%,1.6KV,BK,23x17x1 2.2nF,5%,1.6KV,TP,23x16x9 5.2nF,5%,630V,TP,19x7x13,7.5 1uF,20%,50V,GP,TP,5x11,5 100nF,5%,250V,TP,19x14.5x6.5 150nF,5%,250V,TP,19x16x7.5,7 1uF,20%,50V,GP,TP,5x11,5 220nF,5%,250V,TP,19x22x10,7 300nF,5%,250V,TP,20x18.5x10 1uF,20%,50V,GP,TP,5x11,5 680nF,5%,250V,TP,26x20.5x12 300nF,5%,250V,TP,20x18.5x10 270nF,5%,250V,TP,20x18.5x10 15nF,10%,250V,TP,13X9.0X4.5m 10nF,5%,250V,TP,13x4.5x9mm,7 3.3UF,20%,50V,BP,TP,5X11,5 330pF,10%,500V,Y5P,TP,6x4 220pF,10%,1KV,Y5P,TP,6x5 22nF,5%,100V,TP,7.2x4.5x9.0mm 22nF,5%,100V,TP,7.2x4.5x9.0mm 10uF,20%,16V,GP,TP,5x11,2.5 2.2nF,5%,100V,TP,5.5X10X2.9,5 2.2nF,5%,100V,TP,5.5X10X2.9,5 220nF,20%,50V,GP,5x11,5 10nF,+80-20%,500V,Y5V,TP 1nF,10%,500V,Y5P,TP,8.5x5 2.2uF,20%,250V,GP,TP,8x11.5,5 2.2uF,20%,250V,GP,TP,8x11.5,5 33nF,5%,100V,TP,5.8x12.5x3,5 3.3nF,5%,100V,TP,5.8x12.5mm,5 10nF,10%,1KV,Y5P,BK,20x5, 1nF,10%,500V,Y5P,TP,8.5x5 470nF,20%,50V,GP,TP,5x11,2.5 10nF,5%,100V,TP,7x3.2x7mm,5mm 10uF,20%,16V,GP,TP,5x11,2.5 100pF,10%,500V,Y5P,TP,6x4 150nF,10%,275VAC,BK,26x16.5x 150nF,10%,275VAC,BK,26x16.5 2.2nF,20%,125V,Y5U,TP,11
Remarks
17" 15"
!
17" 15"
! !
17" 15" 17" 15"
SDD,TSB PHS
15"
17" 15" 17" 17"
15" 17"
17" 17"
! ! !
7-2
DP15H*/DP17L*
7 Electrical Parts List
Loc. No. C604 C607 C608 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C621 C622 C623 C626 C627 C630 C631 CIS CIS CLAMP CN201 CN202 CN301 CN302 CN303 CN304 CN401 CN402 CN501 CN501+G2Y CN502 CN502 CN601 D301 D401 D402 D403 D404 D405 D406
Code No. 2201-000023 2202-002009 2401-003367 2401-000971 2301-000284 2401-000613 2401-000613 2201-000012 2201-000019 2201-000291 2201-000023 2201-000023 2401-000039 2201-000469 2401-000540 2401-001551 2401-001551 2401-000039 2401-000039 2401-000025 2401-000292 2401-001561 2202-002009 BH39-00016A 0402-001257 6502-000001 3711-003895 3711-003873 3711-001483 BH71-40300A BH71-40300A 3711-000197 BH71-40300A BH71-40300A BH71-40300A BH39-00014A 3711-001483 3711-000024 3721-001027 0402-000274 0402-000274 0402-000006 0402-000006 0402-000006 0402-000274 0402-001025
Description C-CERAMIC,DISC C-CERAMIC,MLC-AXIAL C-AL C-AL C-FILM,PEF C-AL C-AL C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-CERAMIC,DISC C-AL C-CERAMIC,DISC C-AL C-AL C-AL C-AL C-AL C-AL C-AL C-AL C-CERAMIC,MLC-AXIAL CBF-SIGNAL DIODE-RECTIFIER CABLECLAMP CONNECTOR-HEADER CONNECTOR-HEADER CONNECTOR-HEADER PIN-HINGE PIN-HINGE CONNECTOR-HEADER PIN-HINGE PIN-HINGE PIN-HINGE CBF-HARNESS CONNECTOR-HEADER CONNECTOR-HEADER PLUG-ACPOWER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER
Specification 2.2nF,20%,125V,Y5U,TP,11 100nF,+80-20%,50V,Y5 180uF,20%,400V,GP,BK,25x35mm,1 22uF,20%,50V,WT,TP,6x11mm,5mm 47nF,5%,100V,TP,8.5x12.5mm,5m 1uF,20%,50V,WT,TP,5x11,5 1uF,20%,50V,WT,TP,5x11,5 220pF,10%,1KV,Y5P,TP,6x5 10nF,+80-20%,500V,Y5V,TP 1nF,10%,500V,Y5P,TP,8.5x5 2.2nF,20%,125V,Y5U,TP,11x 2.2nF,20%,125V,Y5U,TP,11x 1000uF,20%,16V,GP,TP,10x16,5 330pF,10%,500V,Y5P,TP,6x4 150uF,20%,63V,LZ,TP,10x25,5 47uF,20%,35V,GP,TP,6.3x11,5 47uF,20%,35V,GP,TP,6.3x11,5 1000uF,20%,16V,GP,TP,10x16,5 1000uF,20%,16V,GP,TP,10x16,5 100uF,20%,16V,GP,TP,6.3x11,5 100uF,20%,16V,WT,TP,8x11.5mm,5 47uF,20%,35V,WT,TP,8x11.5,5 100nF,+80-20%,50V,Y5 -,1550MM,-,IVORY(IV01),2990 DTV32F,1500V,15A,TO-220A DAWH-5NB,D15,L35,NTR,NYLON66 BOX,13P,1R,2mm,STRAIGHT BOX,7P,1R,2mm,STRAIGHT NOWALL,3P,1R,5.0mm,STRA -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK 1WALL,3P,1R,2.5mm,STRAI -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK -,BRASS,D2.36,SN,HEAT/SINK 1P,280MM,RED,UL1032,AWG22,YF NOWALL,3P,1R,5.0mm,STRA BOX,3P,1R,2.5mm,STRAIGH 3P,NI UF4004,400V,1A,DO-41,TP UF4004,400V,1A,DO-41,TP 1N4007GP,1000V,1A,DO-41 1N4007GP,1000V,1A,DO-41 1N4007GP,1000V,1A,DO-41 UF4004,400V,1A,DO-41,TP ERD07-15,1500V,1.5A
Remarks
!
! !
17" 15"
15" 17"
!
17" 15"
!
DP15H*/DP17L*
7-3
7 Electrical Parts List
Loc. No. D407 D408 D409 D410 D411 D412 D413 D420 D421 D422 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D601 D602 D604 D605 D606 D607 D608 D609 D610 D611 D612 D614 D615 D616 FBT FH1 FUSE GT601 GT602 GT603 GT604 HS301 HS401 HS402
Code No. 0402-001118 0402-001255 0402-001256 0402-000546 0402-000546 0402-000546 0402-000546 0401-000005 0401-000005 0401-000005 0401-000005 0402-000012 0402-000546 0402-000546 0401-000004 0402-000546 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0401-000005 0402-000103 0401-000005 0402-000012 0402-000012 0402-000546 0401-000005 0402-000274 0402-000005 0402-000012 0402-001118 0402-000546 0402-000546 0401-000005 0401-000005 6502-000001 3602-000001 3601-000004 BH71-40300A BH71-40300A BH71-40300A BH71-40300A BH99-00002A BH99-00006A BH99-00005A
Description DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-SWITCHING DIODE-BRIDGE DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-RECTIFIER DIODE-SWITCHING DIODE-SWITCHING CABLECLAMP FUSE-CLIP FUSE-FERRULE PIN-HINGE PIN-HINGE PIN-HINGE PIN-HINGE ASSY,HEAT/SINK ASSY,HEAT/SINK ASSY,HEAT/SINK
Specification UF1G,400V,1.2A,DO-204AL DTV56F,1500V,10A,TO-220A SUF30JL,600V,3A,P600,BK TVR10G,400V,1.0A,DO-41,T TVR10G,400V,1.0A,DO-41,T TVR10G,400V,1.0A,DO-41,T TVR10G,400V,1.0A,DO-41,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T UF4007,1KV,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,T TVR10G,400V,1.0A,DO-41,T 1SS244,250V,200mA,DO-34 TVR10G,400V,1.0A,DO-41,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T D2SBA60,600V,1.5A,SIP-4,ST 1N4148,75V,200MA,DO-35,T UF4007,1KV,1A,DO-41,TP UF4007,1KV,1A,DO-41,TP TVR10G,400V,1.0A,DO-41,T 1N4148,75V,200MA,DO-35,T UF4004,400V,1A,DO-41,TP 31DF4,400V,3A,DO-201AD,B UF4007,1KV,1A,DO-41,TP UF1G,400V,1.2A,DO-204AL, TVR10G,400V,1.0A,DO-41,T TVR10G,400V,1.0A,DO-41,T 1N4148,75V,200MA,DO-35,T 1N4148,75V,200MA,DO-35,T DAWH-5NB,D15,L35,NTR,NYLON66 30mohm 250V,3.15A,SB,CERAMIC,5x20m BRASS,D2.36,SN,HEAT/SINK BRASS,D2.36,SN,HEAT/SINK BRASS,D2.36,SN,HEAT/SINK BRASS,D2.36,SN,HEAT/SINK H/SV.IC,SCREW+NUT,KA2142 H/S,SCREW+NUT,IRF630 H/S,SCREW+NUT,IRF630
Remarks
17"
17"
!
15"
!
7-4
DP15H*/DP17L*
7 Electrical Parts List
Loc. No. HS501 HS501 HS601 IC201 IC201_SOCK IC202 IC301 IC401 IC601 IC602 IC603 IC604 IC605 L401 L402 L403 L601 OP201 Q301 Q302 Q303 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q409 Q410 Q412 Q413 Q414 Q415 Q416 Q501 Q502 Q503 Q551 Q601 Q602 Q604 Q608 Q609 Q610 R200
Code No. BH99-00001B BH99-00001A BH99-00003A BH09-00006A 3704-001071 1103-001149 1204-001508 1204-001509 BH13-00004A 1203-000165 1201-000229 1203-000001 1203-000495 BH27-20345B BH27-00005A BH27-20343H BH27-00007A 0601-001147 0501-000586 0501-000303 0501-000586 0501-000122 0505-001309 0501-000372 0502-001129 0501-000303 0501-000303 0501-000586 0502-000465 0505-001309 0505-001309 0501-000404 0501-000321 0501-000586 0501-000586 0501-000586 0501-000416 0501-000143 0501-000303 0501-000413 0501-000586 0501-000122 0501-000404 0501-000586 0501-002228 0501-000586 2001-000869
Description ASSY,HEAT/SINK ASSY,HEAT/SINK ASSY,HEAT/SINK MICOM MASKING SOCKET-IC IC-EEPROM IC-VERTICALDEF. IC-HOR./VER.PROCESSO IC-HYBRID IC-POSI.ADJUSTREG. IC-OPAMP IC-POSI.FIXEDREG. IC-RESET COIL-CHOKE COIL-CHOKE COIL-PEAKING COIL-LINEFILTER LED TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL FET-SILICON TR-SMALLSIGNAL TR-POWER TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-POWER FET-SILICON FET-SILICON TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL TR-SMALLSIGNAL R-CARBON
Specification H/SFBT,SPRING,KA5802,DTV5 H/SFBT,SPRING,KA5802,DTV3 H/SPOWER,SPRING,DP104 DM024, 42P 42P,DIP,SN,1.778mm 24C041,4KBIT,DIP,8P,300MIL,10M KA2142,SIP,10P,-,PLASTIC TDA4859,DIP,32P,400 DP104S,T0-220-52,5P,POWER SW 78R12,TO-220,3P,1 324,DIP,14P,300MIL,QUAD,100V/m 7805,TO-220,3P,-,PLAST 7045,T0-92,3P,-,PLASTIC,4.3/4 150uH,10%,DR1415(L-81,C:8.0) 120UH,10%,AR-06*30,BULK 2.7MH,10%,DR8*8,TP 25MHMIN,-,SQE2424,BUL ROUND,GRN,4.75mm,565nm KSC945,NPN,250mW,TO-92,TP KSA733,PNP,250mW,TO-92,TP KSC945,NPN,250mW,TO-92,TP 2N3904,NPN,625mW,TO-92,TP IRF630,N,200V,10A,0.4OHM,100 KSC2383-Y,NPN,900mW,TO-92 KSC5802,NPN,70W,TO-3PF,ST,5 KSA733,PNP,250mW,TO-92,TP KSA733,PNP,250mW,TO-92,TP KSC945,NPN,250mW,TO-92,TP KTD2058-Y,NPN,25W,TO-220IS,ST IRF630,N,200V,10A,0.4OHM,100 IRF630,N,200V,10A,0.4OHM,100 KSD1616-Y,NPN,750mW,TO-92 KSB1116-Y,PNP,0.75W,TO-92 KSC945,NPN,250mW,TO-92,TP KSC945,NPN,250mW,TO-92,TP KSC945,NPN,250mW,TO-92,TP KSP92,PNP,625mW,TO-92,TP 2N6520,PNP,625mW,TO-92 KSA733,PNP,250mW,TO-92,TP KSP44,NPN,625mW,TO-92,5 KSC945,NPN,250mW,TO-92,TP 2N3904,NPN,625mW,TO-92,TP KSD1616-Y,NPN,750mW,TO-92 KSC945,NPN,250mW,TO-92,TP KTA1281,PNP,1000MW,TO-92 KSC945,NPN,250mW,TO-92,TP 56OHM,5%,1/8W,AA,TP,1.8X3.2MM
Remarks 17" 15"
!
!
17"
DP15H*/DP17L*
7-5
7 Electrical Parts List
Loc. No. R201 R202 R203 R204 R206 R207 R208 R209 R210 R211 R211 R212 R213 R214 R215 R216 R217 R218 R219 R220 R221 R222 R223 R224 R225 R229 R230 R231 R232 R233 R234 R235 R236 R301 R302 R303 R304 R306 R307 R308 R309 R309 R310 R311 R312 R315 R315
Code No. 2001-000786 2001-000290 2001-000786 2001-000786 2001-000515 2001-000869 2001-000869 2001-000734 2001-000472 2001-000904 2001-000924 2001-000613 2001-000429 2001-000429 2001-000281 2001-000281 2001-000281 2001-000281 2001-000290 2001-000281 2001-000734 2001-000734 2001-000038 2001-000869 2001-000869 2001-000281 2001-000290 2001-000241 2001-000812 2001-000331 2001-000563 2001-000734 2001-000290 2001-000869 2004-000580 2001-000890 2001-000890 2004-001022 2001-001053 2001-001088 2004-004014 2004-004424 2004-001136 2001-000890 2001-000812 2004-004014 2004-001816
Description R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-METAL R-CARBON(S) R-CARBON(S) R-METAL R-METAL R-METAL R-CARBON R-CARBON R-METAL R-METAL
Specification 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 220OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 620OHM,5%,1/8W,AA,TP,1.8X3.2MM 680OHM,5%,1/8W,AA,TP,1.8X3.2MM 3.9KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 390OHM,5%,1/4W,AA,TP,2.4X6.4MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 22Kohm,1%,1/4W,AA,TP,2.4x6.4mm 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4m 1.5OHM,5%,1/2W,AA,TP,2.4X6.4 1KOHM,5%,1/2W,AA,TP,2.4X6.4M 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 3.0ohm,1%,1/4W,AA,TP,2.4x6.4mm 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4m 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mm 3.3ohm,1%,1/4W,AA,TP,2.4x7mm
Remarks
17" 15"
17" 15"
17" SDD,TSB 15" PHS
7-6
DP15H*/DP17L*
7 Electrical Parts List
Loc. No. R316 R317 R318 R319 R320 R321 R322 R323 R324 R325 R326 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414 R415 R416 R417 R417 R418 R418 R419 R420 R420 R422 R423 R423 R424 R425 R425 R426 R427 R428 R428 R429 R430 R431
Code No. 2001-000281 2001-000561 2001-000766 2001-000947 2001-000331 2001-000591 2001-000890 2001-000022 2001-000660 2003-000805 2003-000805 2001-000869 2004-001226 2004-000498 2001-000591 2001-000522 2001-000109 2001-000429 2001-000812 2003-000650 2001-001096 2001-000290 2001-001038 2001-001038 2003-000429 2001-000107 2001-000290 2001-000890 2001-000221 2001-000449 2001-000397 2001-000354 2004-000327 2001-001006 2001-000258 2001-000472 2004-000284 2001-000044 2001-000042 2001-000110 2001-000429 2003-000653 2003-000608 2001-000052 2001-001078 2003-000407
Description R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON R-METALOXIDE(S) R-METALOXIDE(S) R-CARBON R-METAL R-METAL R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON R-METALOXIDE(S) R-CARBON(S) R-CARBON R-CARBON(S) R-CARBON(S) R-METALOXIDE(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-CARBON R-METALOXIDE(S) R-METALOXIDE(S) R-CARBON(S) R-CARBON(S) R-METALOXIDE(S)
Specification 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 27KOHM,5%,1/4W,AA,TP,2.4X6.4MM 43KOHM,5%,1/8W,AA,TP,1.8X3.2MM 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 12KOHM,5%,1/8W,AA,TP,1.8X3.2MM 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 33OHM,5%,1/2W,AA,TP,2.4X6.4M 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 82ohm,5%,1W,AA,TP,3.3x9m 82ohm,5%,1W,AA,TP,3.3x9m 56OHM,5%,1/8W,AA,TP,1.8X3.2MM 750ohm,1%,1/4W,AA,TP,2.4x6.4mm 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4m 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MM 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 470OHM,5%,1/2W,AA,TP,2.4X6.4 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12m 2.2OHM,5%,1/2W,AA,TP,2.4X6.4 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 0.56OHM,5%,1/2W,AA,TP,2.4X6 0.56OHM,5%,1/2W,AA,TP,2.4X6 1.5Kohm,5%,2W,AA,TP,4x12 150KOHM,5%,1/2W,AA,TP,2.4X6. 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 180KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM 150Kohm,1%,1/4W,AA,TP,2.4x6.4m 82OHM,5%,1/8W,AA,TP,1.8X3.2MM 1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 12Kohm,1%,1/4W,AA,TP,2.4x6.4mm 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 10OHM,5%,1/4W,AA,TP,2.4X6.4MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,3W,AA,TP,6x16m 270ohm,5%,3W,AA,TP,6x16m 3.3KOHM,5%,1/2W,AA,TP,2.4X6 15KOHM,5%,1/2W,AA,TP,2.4X6.4 0.6ohm,5%,2W,AA,TP,4x12m
Remarks
! !
SDD TSB, PHS 15" 17" 15"
15" 17" 15"
17" 15"
17"
DP15H*/DP17L*
7-7
7 Electrical Parts List
Loc. No. R431 R432 R434 R435 R436 R437 R438 R438 R439 R440 R441 R443 R443 R444 R445 R446 R446 R446 R447 R448 R449 R450 R451 R452 R453 R454 R500 R501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R516 R516 R517
Code No. 2005-001071 2001-000020 2001-000290 2001-000786 2001-000290 2001-000786 2001-000290 2001-000290 2001-000786 2001-000947 2001-000411 2003-000502 2003-000578 2003-000767 2001-000019 2001-000117 2001-000114 2001-000028 2003-000777 2003-000777 2001-000211 2001-000522 2001-000290 2001-000290 2001-000290 2003-000650 2001-000435 2001-000472 2004-000979 2001-000449 2001-000008 2001-000241 2004-000657 2004-000216 2001-001052 2001-001052 2001-000837 2001-000478 2001-000786 2001-001115 2001-000837 2001-000546 2004-000368 2004-000398 2004-000327 2001-000987
Description R-WIREWOUND R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METALOXIDE(S) R-METALOXIDE(S) R-METALOXIDE(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-METALOXIDE(S) R-METALOXIDE(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-METALOXIDE(S) R-CARBON R-CARBON R-METAL R-CARBON R-CARBON R-CARBON R-METAL R-METAL R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON R-CARBON R-METAL R-METAL R-METAL R-CARBON
Specification 0.82OHM,5%,3W,AA,TP,5.5X15M 22OHM,5%,1/2W,AA,TP,2.4X6.4M 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 18KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150ohm,5%,2W,AA,TP,4x12m 220ohm,5%,2W,AA,TP,4x12m 680ohm,5%,2W,AA,TP,4x12m 10OHM,5%,1/2W,AA,TP,2.4X6.4M 68OHM,5%,1/2W,AA,TP,2.4X6.4M 180KOHM,5%,1/2W,AA,TP,2.4X6 100OHM,5%,1/2W,AA,TP,2.4X6.4 68ohm,5%,2W,AA,TP,4x12mm 68ohm,5%,2W,AA,TP,4x12mm 1OHM,5%,1/4W,AA,TP,2.4X6.4MM 22KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330ohm,5%,2W,AA,TP,4x12m 1MOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 47Kohm,1%,1/4W,AA,TP,2.4x6.4mm 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MM 15KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 27Kohm,1%,1/4W,AA,TP,2.4x6.4mm 10Kohm,1%,1/4W,AA,TP,2.4x6.4mm 1.5MOHM,5%,1/2W,AA,TP,2.4X6 1.5MOHM,5%,1/2W,AA,TP,2.4X6 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7OHM,5%,1/4W,AA,TP,2.4X6.4MM 47KOHM,5%,1/8W,AA,TP,1.8X3.2MM 27KOHM,5%,1/2W,AA,TP,2.4X6.4 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM 270KOHM,5%,1/4W,AA,TP,2.4X6.4MM 160KOHM,5%,1/4W,AA,TP,2.4X6.4MM 180KOHM,5%,1/4W,AA,TP,2.4X6.4MM 150Kohm,1%,1/4W,AA,TP,2.4x6.4m 820KOHM,5%,1/4W,AA,TP,2.4X6.4MM
Remarks 15"
17" 15" 17"
17" 15"
17" 15" 15"
!
17"
! ! ! !
!
SDD TSB, PHS 15"
7-8
DP15H*/DP17L*
7 Electrical Parts List
Loc. No. R518 R519 R520 R520 R521 R524 R525 R526 R526 R527 R527 R527 R527 R528 R529 R551 R552 R553 R554 R555 R556 R600 R601 R602 R603 R604 R605 R606 R607 R608 R609 R610 R611 R612 R614 R615 R617 R617 R618 R619 R620 R621 R622 R625 R630 R631 R632
Code No. 2001-001031 2001-000356 2001-000241 2001-000472 2008-001085 2001-000660 2001-000273 2001-000273 2001-000908 2001-000864 2001-000563 2001-000837 2001-000908 2001-000262 2001-000429 2001-000530 2001-000537 2001-001129 2001-001110 2001-000042 2001-000890 2001-001129 2001-001129 2001-000023 2001-000290 2001-000857 2001-000734 2003-000225 2003-000225 2001-000281 2001-000114 2001-000114 2001-001079 2003-000738 2001-001107 2001-001088 2001-001037 2001-001038 2001-000429 2003-000471 2001-000354 2001-000989 2001-000211 2001-000786 2001-000786 2001-000429 2001-000290
Description R-CARBON R-CARBON R-CARBON R-CARBON R-FUSIBLE R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON R-CARBON R-CARBON R-CARBON R-METALOXIDE R-METALOXIDE R-CARBON R-CARBON(S) R-CARBON(S) R-CARBON(S) R-METALOXIDE(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON(S) R-CARBON R-METALOXIDE(S) R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON
Specification 91KOHM,5%,1/8W,AA,TP,1.8X3.2MM 150KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.5KOHM,5%,1/8W,AA,TP,1.8X3.2MM 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/4W,AA,TP,2.4X6MM 33KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 100KOHM,5%,1/8W,AA,TP,1.8X3.2MM 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM 56KOHM,5%,1/8W,AA,TP,1.8X3.2MM 27KOHM,5%,1/8W,AA,TP,1.8X3.2MM 62KOHM,5%,1/8W,AA,TP,1.8X3.2MM 51KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1.8MOHM,5%,1/8W,AA,TP,1.8X3.2MM 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 240KOHM,5%,1/4W,AA,TP,2.4X6.4MM 24KOHM,5%,1/4W,AA,TP,2.4X6.4MM 330KOHM,5%,1/2W,AA,TP,2.4X6 240KOHM,5%,1/2W,AA,TP,2.4X6 1KOHM,5%,1/4W,AA,TP,2.4X6.4MM 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MM 330KOHM,5%,1/2W,AA,TP,2.4X6 330KOHM,5%,1/2W,AA,TP,2.4X6 47OHM,5%,1/4W,AA,TP,2.4X6.4MM 10KOHM,5%,1/8W,AA,TP,1.8X3.2MM 560OHM,5%,1/8W,AA,TP,1.8X3.2MM 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MM 22Kohm,5%,1W,AA,TP,4.3x12m 22Kohm,5%,1W,AA,TP,4.3x12m 100OHM,5%,1/8W,AA,TP,1.8X3.2MM 180KOHM,5%,1/2W,AA,TP,2.4X6 180KOHM,5%,1/2W,AA,TP,2.4X6 15OHM,5%,1/2W,AA,TP,2.4X6.4M 56Kohm,5%,2W,AA,TP,4x12m 220ohm,5%,1/2W,AA,TP,2.4x6.4 1KOHM,5%,1/2W,AA,TP,2.4X6.4M 0.39OHM,5%,1/2W,AA,TP,2.4X6. 0.56OHM,5%,1/2W,AA,TP,2.4X6 1KOHM,5%,1/8W,AA,TP,1.8X3.2MM 10ohm,5%,2W,AA,TP,4x12mm 150KOHM,5%,1/4W,AA,TP,2.4X6.4MM 820KOHM,5%,1/8W,AA,TP,1.8X3.2MM 1OHM,5%,1/4W,AA,TP,2.4X6.4MM 47KOH