Text preview for : GTW-P42M203.pdf part of Gateway P42M203 Schematics & Service Manual
42" Plasma P42M203
Back to : GTW-P42M203.pdf | Home
CONFIDENTIAL PDP-014-1 (Module Format) Issued:June.20.2003 Version:1.0
42" PDP SERVICE MANUAL MODELGTW-P42M203 Panel:Samsung (VVEPP42SD001F--)
CONTENTS
1. IMPORTANT SAFETY PRECAUTIONS ........1-2 2. SPECIFICATION .....................................2-9 3. FACTORY & ELECTRONIC ADJUSTMENT ..3-7 4. BLOCK DIAGRAM ...................................4-6 5. TROUBLE SHOOTING GUIDES ................5-6 6. B.O.M OF BOARD ASSEMBLY.....................6-23 7. P.C.BOARD TOP VIEW...............................7-8 8. ELECTRONIC MODULE LIST ......................8-1 9. EXPLODED VIEW............. ......................9-1 10.PACKAGING OF THE LIST .......................10-1
IMPORTANT SAFETY PRECAUTIONS
VER1.0
1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items. a. Be sure that no built-in protective devices are defective and/or have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including, but not limited to, nonmetallic control knobs, insulating fish papers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers into, Such opening include, but are not limited to, (1) spacing between the picture tube and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover. c. Leakage Current Check--With the instrument completely reassembled, plug the AC line cord directly into -- a 120V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institutes (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 478. With the instrument AC switch first in the ON position and then in the OFF position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle bracket, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 3.5 milliamp. Reverse the instrument power cord plug in the outlet and repeat test. ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER.
AC Leakage Test
LEAKAGE CURRENT TESTER DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 3. WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
(READING SHOULD NOT BE ABOVE 3.5mA)
+ -
EARTH GROUND
2. Read and comply with all caution and safety-related notes on or inside the Monitor cabinet. 3. Design Alteration Warning--Do not alter or add to the mechanical or electrical design of this unit. Design -- alterations and additions, including, but not limited to, circuit modifications and the addition of the items such as auxiliary audio and/or video output connections might alter the safety characteristics of this Monitor and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and will make you, the service, responsible for personal injury or property damage resulting there from.
1-1
IMPORTANT SAFETY PRECAUTIONS
VER1.0
4. Primary Chassis Warning -- a. Certain Monitor chasses are electrically connected directly to one conductor of the AC power cord. They may be safely serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the groundside of the AC power source. To confirm that the AC power plug is inserted correctly use an AC voltmeter to measure the voltage potential between the chassis and a known earth ground. If the voltage reading is greater than 1.0V, remove and reinsert the AC power plug in opposite polarity and re-measure the voltage potential between the chassis and a known earth ground. b. Certain Monitor chasses have 85V AC (RMS) between chassis and earth ground regardless of the AC plug polarity. These chasses can be safely serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection. c. Some Monitor chasses have a secondary ground systems in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts--be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, e. antenna wiring. Inspect in all areas for pinched, out-of-place, or frayed wiring. Do not change the spacing between components or the spacing between the printed-circuit board and components. Last but not least, visually check the AC power cord to ensure no outer appearance damage is present. 6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard(s). 7. PRODUCT SAFETY NOTICE -- Many electrical and mechanical parts have special safety-related characteristics some of which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified in this service data by shading with a mark on schematics and by shading or a mark in the parts list. Use of a replacement part that does not have the same safety characteristics as the recommended replacement part in the Service data parts list might create shock, fire, and/or other hazards.
1-2
SPECIFICATION
1.
VER1.0
SCOPE: These specifications describe all the characteristics of the 42 inch color monitor. ELECTRICAL REQUIREMENTS: 2.1. Display panel: a. b. c. d. e. f. 2.2. Screen size Aspect ratio Number of pixels Pixel Pitch Luminance Chromatically Specification Diagonal 42 inch 16:9 wide 852(Horizontal, RGB Trio ) X 480(Vertical)pixels 1.08mm X 1.08mm 2 570cd/m ,at APL13% x=0.270±0.03, y=0.300±0.03(color temperature mode 1 : ) ± ± at center block white pattern 100% (mosaic).
2.
Power Source: a. b. c. d. Input voltage Input current Inrush current Power consumption 100 ~ 240 Vac , 50 / 60 Hz 3.3A 60 A p-p/20ms Max. 380±10% Watts ( at 110Vac/color bar pattern) ± 5 Watts Max. (at 110Vac)
e. Stand-by & DPMS 2.3. Input Signal:
2.3.1 Connector Type:
RCA Jack for audio, video Y/CB/CR and Y/PB/PR 6 pin Din S-terminal 9 pin D-SUB 15 pin D-SUB 24 pin DVI
2.3.2 Video/S-Video Signal: a. b. c. d. Type Polarity Amplitude Frequency Analog Positive Video 1Vp-p , (priority S-Video) Y=1Vp-p H: 15.734KHz V: 60Hz(NTSC) H: 15.625KHz V: 50Hz(PAL) 75 ohms
C=0.286Vp-p
e. Input impedance 2.3.3 Y/CB/CR or Y/PB/PR Signal: a. Type b. Polarity c. Amplitude d. Frequency Y/CB/CR Y/PB/PR:HDTV
Analog Positive AV: 1Vp-p (with sync) S-Video: Y: 1Vp-p ,C: 0.286Vp-p H: 15.734KHz ,V: 60Hz (NTSC) H: 15.625KHz ,V: 50Hz (PAL) 1. 31KHz/60Hz (480P) 2. 45KHz/60Hz (720P) 33KHz/60Hz(1080I)
2-1
SPECIFICATION
2.3.4 RGB Signal: a. Type b. Polarity c. Amplitude d. Frequency TTL Positive or Negative RGB: 0.7Vp-p H: support to 31K~91KHz V: support to 50~85Hz
VER1.0
2.3.5 DVI Signal: a. Type b. Polarity c. Frequency 2.3.6 Audio Signal: Digital Positive or Negative H: support to 31K~63KHz V: support to 50~85Hz Analog 500mV rms /more than 22Kohm
2.3.7 Pin Assignments For D-SUB Connector (In / Loop Out): Pin 1 2 3 4 5 Signal Assignment RED GREEN BLUE GND GND Pin 6 7 8 9 10 Signal Assignment RED GND GREEN GND BLUE GND NC GND Pin 11 12 13 14 15 Signal Assignment GND SDA H-SYNC V-SYNC SCL
2.3.8 Pin Assignments For 24 Pin DVI Connector(Digital Only): Pin 1 2 3 4 5 6 7 8 Signal Assignment TMDS Data 2TMDS Data 2+ TMDS Data 2/4 Shield TMDS Data 4TMDS Data 4+ DDC Clock DDC Data No Connect Pin 9 10 11 12 13 14 15 16 Signal Assignment TMDS Data 1TMDS Data 1+ TMDS Data 1/3 Shield TMDS Data 3TMDS Data 3+ +5V Power Ground (For +5V) Hot Plug Detect Pin 17 18 19 20 21 22 23 24 Signal Assignment TMDS Data 0TMDS Data 0+ TMDS Data 0/5 Shield TMDS Data 5TMDS Data 5+ TMDS Clock Shield TMDS Clock + TMDS Clock -
2-2
SPECIFICATION
2.3.9 RGB/DVI For VESA Standard: Mode No Resolution Refresh Rate (Hz) 60 72 75 85 56 60 72 75 85 60 70 75 85 60 75 85 70 50 60 60(I) 70 60 Horizontal Vertical Frequency Frequency (K Hz) 31.5 37.9 37.5 43.3 35.1 37.9 48.1 46.9 53.7 48.4 56.5 60.0 68.7 63.98 79.98 91.15 31.50 31.5 45.15 33.78 31.46 31.72 (Hz) 59.94 72.81 75 85.01 56.25 60.317 72.19 75 85.06 60.01 70.07 75.03 84.99 60.02 75.03 85.02 70 50 60 60 70.08 60.41 Vertical Sync Polarity (TTL) + + + + + + + + + + + -
VER1.0
Horizontal Sync Polarity (TTL) + + + + + + + + + + -
Dot rate (MHz) 25.175 31.500 31.500 36.000 36.000 40.000 50.000 49.500 56.250 65.000 75.000 78.750 94.500 108.00 135.00 157.50 25.175 25.175 74.250 74.250 28.320 34.00
1 2 3 4 5 6 7
8
9 10 11 12 13 14 15 16 18 19 20 21 22 23
640(VGA)×480 × 640(VGA)×480 × 640(VGA)×480 × 640(VGA)×480 × 800(SVGA)×600 × 800(SVGA)×600 × 800(SVGA)×600 × 800(SVGA)×600 × 800(SVGA)×600 × 1024(XGA)×768 × 1024(XGA)×768 × 1024(XGA)×768 × 1024(XGA)×768 × 1280(SXGA)×1024 × 1280(SXGA)×1024 × 1280(SXGA)×1024 × 640(VGA)×350 × 640(VGA)×480 × 1280(HDTV)×720P × 1920(HDTV)×1080I × 720(DOS)×400 × 852(WGA)×480 ×
RGB/DVI For Apple Standard. Mode No Resolution Refresh Rate (Hz) 75 75 75 Horizontal Vertical Frequency Frequency (K Hz) 68.85 49.73 68.68 (Hz) 75.00 74.55 75.06 Vertical Sync Polarity (TTL) Horizontal Sync Polarity (TTL) Dot rate (MHz) 57.283 57.283 100.000
24 25 26
640×870 × 832 x 624 1152 x 870
Attention : For DVI is not supported. 2.3.10 Y/PB/PR For Component: Mode No 1 2 3 Resolution 640 × 480P 1920 × 1080I 1280 × 720P Refresh Rate 60 60 60
2-3
SPECIFICATION
2.4. Display Performance Requirements: The data of display performance are measured based on the following. Conditions unless otherwise specified. a. b. c. d. e. f. Ambient temperature Warm up period Line input voltage : Viewing distance Display mode Brightness condition
VER1.0
25±5 ± 30 minutes Min. 100 Vac ~ 240 Vac (50 / 60 Hz) Distance from screen is 81 cm Test with window white pattern mode if not specified. Press recall bottom to set default brightness Support to 1280 x 1024
2.4.1 Maximum Resolution:
2.4.2 Horizontal Size (Standard) Vertical Size (Standard) 2.4.3 Horizontal Size (Max.) Vertical Size (Max.) 2.4.4 Maximum Brightness Level: a. 100% center block white pattern(mosaic) b. raster background 2.5. Operation:
920±8 mm (for mode 126) ± 518±8 mm (for mode 126) ± Mode 1~26 Mode 1~26 full-scan full-scan
Timing Mode 1 More than 30FL (while pressing recall button to set default brightness) with contrast / brightness at Max. and black signal) less than 0.4FL
Main unit button
IR Remote Control
Main power switch (power ON /OFF) Power ON/OFF Input Mode (Video1 -> S-Video1 -> Video2 or S-Video2 -> Y/PB/PR 1 or Y/CB/CR 1 -> Y/PB/PR 1 or Y/CB/CR 1 -> RGB -> DVI->Video1 run in circle) Menu key -,+ Adjustment -,+ Power on/off Input Mode (same as Main unit button) Volume -,+ Wide , Video/S video input:4:3/16:9/ZOOM1/ZOOM2 Analog RGB input :W4:3/W16:9 Menu -,+ Adjustment -,+ RECALL PIP ,POP ,SWAP ,MUTE
2.5.1 Adjustable Items: AV/S-video input Y/CB/CR Analog RGB input Brightness, Contrast, Color , Tint, Sharpness Color Temperature Display position : Brightness, Contrast, Vertical position, Vertical width, Horizontal position, Horizontal width, Color Temperature Clock phase, DPMS. Brightness, Contrast, Vertical position, Vertical width, Horizontal position, Horizontal width, Color Temperature, DPMS
DVI
input
2-4
SPECIFICATION
3. DIMENSIONS: Width Height Depth 3.1. Package Dimensions: Width Height Depth 3.2. Weight: Net weight Gross weight 4. 4.1. ENVIRONMENT: Operating: Temperature Relative humidity Pressure 4.2. Non-Operating: Temperature Relative humidity Pressure Vibration 4.3. Acoustics: (IHF A-weighted 1meter) SOUND: 500W Max. a. Residual hum (at volume min) b. Practical max. Audio output (at 10% THD max.) 1.0vp-p 1K Hz input 5W +5W Max. /12 ohm c. Sound distortion (at 250 mw 1K Hz) 1% Max. d. Sound distortion (at i.ovp-p 1kHz input volume max ) 9% max e. Audio output (input at 1.4VP-P) 1.0 VP-P 1000W Max. f. Max. hum (at volume max) 150mV ±3dB g. Sensitivity (at volume max. O/P 1W) at 1KHz AV Input h. Audio Fidelity (1KHz 0dB,corrected for emphasis characteristics) 6dB ±3dB BBE ON 60Hz 8dB ±3dB 10KHz -6dB ±3dB WOOFER & BBE OFF 100Hz -2dB ±3dB 10KHz -20~60 20~90% 700~1114hpa X/Y/Z, 0.5G/10~55Hz(sweep), 10 minutes 40dB Max. 0~40(32~104) 20~80% 800~1114hpa 1230 mm 960 mm 470 mm Without/Stand 1040mm 648 mm 95mm With/Stand 1040mm 690mm 375 mm
VER1.0
79.4lbs/36 Kgs (w/o stand) 83.8lbs/ 38Kgs (w/ stand) 115lbs/52 Kgs
5.
2-5
SPECIFICATION
6. 6.1 RF RF Sensitivity (Peak) VHF UHF CATV 6.2 CH 2 ~ CH 13 CH 14 ~ CH 69 CH A-5 ~ CH W+29 30dB Max. 30dB Max. 30dB Max.
VER1.0
AFT Pull-In Range VHF UHF CATV CH 2 ~ CH 13 CH 14 ~ CH 69 CH A-5 ~ CH W+29 ±0.6MHz Min. ±0.6MHz Min. ±0.6MHz Min.
6.3
Picture IF Rejection VHF UHF CATV CH 2 ~ CH 13 CH 14 ~ CH 69 CH A-5 ~ CH W+29 50dB Min. 50dB Min. 50dB Min.
6.4
Picture Image Rejection VHF UHF CATV CH 2 ~ CH 13 CH 14 ~ CH 69 CH A-5 ~ CH W+29 40dB Min. 35dB Min. 35dB Min.
6.5
AGC Characteristics AGC Figure Of Merit 50dB Min. RF signal range in which video at PDP drops 6 dB from output level obtained with 100mV input.
6.6 6.7 6.8
RF AGC Cut In Level FM/AM Rejection (100mV at SIF input) Noise Limits Sensitivity
55dB ±2dB 14dB min VHF 45dB max UHF 49dB max
7.
RELIABILITY REQUIREMENT: The MTBF needs 20000hrs under operation 25±5(half luminosity, motion picture) ± REGULATORY REQUIREMENTS: Safety Requirement: a. UL b. CSA c. TUV Safety of information technology equipment including electrical business equipment Safety of information technology equipment including electrical business equipment
8. 8.1
8.2
Emission Requirement: The unit shall meet the EMI limits in all screen modes. For EMI testing, the unit must be failed with the screen pattern consisting of scrolling capital "H" characters also the brightness contrast will be adjusted to max. Level. a. FCC class A part 15
2-6
SPECIFICATION
8.3 Transit test a. b. Drop Test Vibration Test 1. 2. 3. 8.4 Forward and backward Right and left Up and down 30 minutes 1000 c.p.m 30 minutes 1000 c.p.m 30 minutes 1000 c.p.m 200mm max.
VER1.0
Power Management: Mode Normal Stand-by Power saving H-sync Pulse No pulse Pulse No pulse V-sync Pulse No pulse No pulse Pulse Video Active No video Blanked Power dissipation Normal power Power off Less than 5 watts
This Plasma display is Energy star compliant when used with a computer equipped with DPMS.
Note: The power indicator LED color is green in normal state, yellow in stand-by and power saving state.
9. 9.1 VIDEO & AUDIO Video Signal Output (impedance 75 ohm) 1.0 Vp-p ±0.2Vp-p
(input signal at 1.0 Vp-p ±0.2Vp-p)
2-7
SPECIFICATION
APPENDIX A : Preset Timing Chart
VER1.0
Item A B C D E F G H I
Description: Total time Active display area including borders Active display area excluding borders Left/Top border Right/bottom border Blanking time Front porch Sync-width Back porch
Mode No Resolution & Refresh Rate Pixel Horizontal visible Horizontal total Horizontal front porch Horizontal sync Horizontal back porch Horiz blanking time Vertical visible Vertical total Vertical front porch Vertical sync Vertical back porch Vertical blanking time Horizontal frequency Vertical frequency Vertical sync polarity Horiz sync polarity Dot rate
1 640 480 60 25.175 640 800 24 96 40 160 480 525 18 2 25 45 31.469 59.94 25.175
2 640 480 72 31.5 640 832 32 40 120 192 480 520 17 3 20 40 37.9 72.81 31.5
3 640 480 75 31.5 640 840 16 64 120 200 480 500 1 3 16 20 37.5 75 31.5
4 640 480 85 36 640 832 56 56 80 192 480 509 1 3 25 29 43.3 85.01 36
5 800 600 56 36 800 1024 24 72 128 224 600 625 1 2 22 25 35.1 56.25 + + 36
6 800 600 60 40 800 1056 40 128 88 256 600 628 1 4 23 28 37.9 60.317 + + 40
7 800 600 72 50 800 1040 56 120 64 240 600 666 37 6 23 66 48.1 72.19 + + 50
8 800 600 75 49.5 800 1056 16 80 160 256 600 625 1 3 21 25 46.9 75 + + 49.5
9 800 600 85 56.25 800 1048 32 64 152 248 600 631 1 3 27 31 53.7 85.06 + + 56.25
Hz MHz Dots Dots Dots Dots Dots Dots Lines Lines Lines Lines Lines Lines KHz Hz TTL TTL MHz
2-8
SPECIFICATION
Mode No Resolution & Refresh Rate Pixel Horizontal visible Horizontal total Horizontal front porch Horizontal sync Horizontal back porch Horiz blanking time Vertical visible Vertical total Vertical front porch Vertical sync Vertical back porch Vertical blanking time Horizontal frequency Vertical frequency Vertical sync polarity Horiz sync polarity Dot rate 10 1024 768 60 65 1024 1344 24 136 160 320 768 806 3 6 29 38 48.4 60.01 65 11 1024 768 70 75 1024 1328 24 136 144 304 768 806 3 6 29 38 56.5 70.07 75 12 1024 768 75 78.75 1024 1312 16 96 176 288 768 800 1 3 28 32 60 75.03 + + 78.75 13 1024 768 85 94.5 1024 1376 48 96 208 352 768 808 1 3 36 40 68.7 84.99 + + 94.5 14 1280 1024 60 108 1280 1688 48 112 248 408 1024 1066 1 3 38 42 63.98 60.02 + + 108 15 1280 1024 75 135 1280 1688 16 144 248 408 1024 1066 1 3 38 42 79.98 75.03 + + 135 16 1280 1024 85 157.5 1280 1728 64 160 224 448 1024 1072 1 3 44 48 91.15 85.02 + + 157.5
VER1.0
18 19 640 640 350 480 70 50 Hz 25.175 25.175 MHz 640 640 Dots 800 800 Dots 16 16 Dots 96 96 Dots 48 48 Dots 160 160 Dots 350 480 Lines 449 629 Lines 37 62 Lines 2 2 Lines 60 85 Lines 99 149 Lines 31.50 31.5 KHz 70 50 Hz TTL TTL 25.175 25.175 MHz
Mode No Resolution & Refresh Rate Pixel Horizontal visible Horizontal total Horizontal front porch Horizontal sync Horizontal back porch Horiz blanking time Vertical visible Vertical total Vertical front porch Vertical sync Vertical back porch Vertical blanking time Horizontal frequency Vertical frequency Vertical sync polarity Horiz sync polarity Dot rate
20 1280 720P 60 74.250 1266 1650 42 63 279 384 687 750 1 6 56 63 45.15 60 74.25
21 1920 1080I 60I 74.25 1901 2201 68 63 169 300 518 562.5 0.5 6 38 44.5 33.78 60 74.25
22 720 400 70 28.320 720 900 18 108 54 180 400 449 12 2 35 49 31.46 70.08 + 28.32
23 852 480 60 30 852 955 19 48 36 103 480 525 10 2 33 45 31.72 60.41 30
24 25 26 640 832 1152 870 624 870 75 75 75 57.283 57.283 100.000 640 832 1152 832 1152 1456 32 32 32 80 64 128 80 224 144 192 320 304 870 624 870 918 667 915 3 1 3 3 3 3 42 39 39 48 43 45 68.85 49.73 68.68 75.00 74.55 75.06 57.283 57.283 100.000
Hz MHz Dots Dots Dots Dots Dots Dots Lines Lines Lines Lines Lines Lines KHz Hz TTL TTL MHz
2-9
FACTORY & ELECTRONIC ADJUSTMENT
VER1.0
1. PANEL Voltage Adjustment The power voltage needs to be re-adjusted and checked whenever the panel module or power board module is changed.
POWER VOLTAGE ADJUSTMENT FOR SAMSUNG TTL PANEL
GND
POWER BOARD DIGITAL BOARD
EXT INT CN01
VA VSC VS VR VSET
Voltage Check Points CN01 SELECT "INT" CN05 SELECT "EXT"
EXT INT CN05
SA Connector: Connect Pins 1 & 5
1. Remove the Image Board to access the Digital Board beneath it. 2. As shown in the diagram above (left), set the CN01 Jumper to "INT" and set the CN05* Jumper to "EXT". 3. Locate the Power Board and the SA Connector (see diagram above: right). Connect pins 1 and 5 of the SA connector. This connection will turn on the Panel Power. 4. Locate the Voltage Label under the upper right speaker holder. The Voltage Label specifies the 5 Voltage Adjustment Parameters and their respective values**. 5. Locate the Voltage Regulator-VR8005 on the Power Board and connect a Multimeter to the VA Voltage Check Point (see diagram above: right) and Ground. Adjust the Voltage Regulator until the Multimeter voltage reading is equivalent to the VA value on the Voltage Label. 6. Repeat Step 5 for VSC, VS, VR and VSET adjustments. Follow the table below for the adjustment sequence and the Voltage Regulator to be adjusted for each Parameter. 1st 2nd 3rd VA VSC VS VR8005 VR8006 VR8003 4th 5th VR VSET VR8001 VR8007
3-1
FACTORY & ELECTRONIC ADJUSTMENT Color Temperature Adjustment
VER1.0
2. Pre-setting Adjustment and Equipment Preparation: (1) Turn on the PDP and let it warm up for at least 30 minutes. (2) Turn on the Color Analyzer (ie. Minolta, Model = CA-100) and reset the Color Analyzer. (3) Change the PDP input mode to DVI and press the "Recall" key on the remote control to have the PDP set recalled back to default factory settings. (4) Set up the Video Pattern Generator (ie. Chroma, Model = C2226) with the following settings: a. Timing: 640 x 480 @ 60Hz, b. Make sure the Output signal is Digital (DVI) Connect the PDP DVI input connector to the Chroma DVI output connector. (5) Dark level and bright level center block definition: A. Dark level center block definition: Pattern set = Pattern name = 1-mosaic, Color form = norm, Background color = 0 Foreground color = 17 According to the C-2226's user manual, appendix analog-color: Normal Pen from Pen 17 = R: 102, G: 102, B: 102 102 (output amplifier)/1024 (total amplifier)=10%, therefore the 10% is the 10 IRE white output pattern. B. Bright level center block definition: Pattern set = Pattern name = 1-mosaic, Color form = norm, Background color = 0 Foreground color = 25 According to the C-2226's user manual, appendix analog-color: Normal Pen from Pen 25 = R: 614, G: 614, B: 614 614 (output amplifier)/1024 (total amplifier)=60%, therefore the 60% is the 60 IRE white output pattern. (6) There are 3 different modes (DVI, RGB and AV) that have Color Temperature settings. For each one of these 3 modes, there are 4 different Color Temperatures (5400K, 6500D, 9300K and 13800K) that can be individually adjusted. Each Color Temperature is adjusted through the dark level, bright level, Gain and Bias values.
3-2
FACTORY & ELECTRONIC ADJUSTMENT
VER1.0
(7) Press the following key sequence to access the Factory Adjustment Menu: Press and hold down the Left Arrow key for at least 5 seconds, then press and hold down the Right Arrow key for at least 5 seconds followed by pressing the FAV.SET key. From the Factory Adjustment Menu, choose the Color Temp. Adj option and the following OSD will appear. DVI (RGB, AV) x=335 GAIN RGB XXX 5400K (6500D, 9300K, 13800K) y=343 BIAS RGB XXX
*Note: When adjusting the DVI and RGB color temperatures, please set the PDP input source so that it matches the color temperature source being adjusted (DVI color temp. to be adjusted with DVI source under DVI mode, RGB color temp. with RGB source under RGB mode, AV color temp. with Composite source under AV1 mode).* (8) Flatly place the Minolta Color Analyzer's Photo Detector in contact with the center of the PDP screen. 3. DVI Mode Color Temperature Adjustment procedure: (1) With the PDP's DVI input connected to Chroma C-2226's DVI output connector, set the Chroma to send a dark level center block signal (10 IRE). Now press the Factory Adjustment key sequence as stated in point (7) above. The DVI 5400K Color Temperature setting menu will appear after choosing the Color Temperature Adjustment option. (2) Press the Left/Right Button to switch between the Bias (R, G, B) and Gain (R, G, B) values. Use the Up/Down Buttons to change the Bias and Gain Values. (3) 5400K dark level center block adjustment procedure: A. Press the Left/Right key on the remote control to select G-BIAS and adjust (using the up/down key) the G-Bias value until Y = 0.4±0.08 FL. B. Press the Left/Right key on the remote control to select R-BIAS and adjust the R-Bias value until x = 335±8 C. Press the Left/Right key on the remote control to select B-BIAS and adjust the B-Bias value until y = 343±8 D. Repeat steps A, B and C until the following final values are obtained: x = 335±8 y = 343±8 Y = 0.4±0.08 FL (4) 5400K bright level center block adjustment procedure: (Please set the Chroma C-2226 DVI bright level center block signal to 60 IRE) A. Select G-GAIN and adjust the G-GAIN value until Y = 30±0.8 FL. B. Select R-GAIN and adjust the R-GAIN value until x = 335±8 C. Select B-GAIN and adjust the B-GAIN value until y = 343±8 D. Repeat steps A, B and C until the following final values are obtained: x = 335±8 y = 343±8 Y = 30±0.8 FL
3-3
FACTORY & ELECTRONIC ADJUSTMENT
VER1.0
(5) Upon completion of Steps 3 and 4 above, press the FAV.SET key for the next Color Temperature setting (54006500D930013800). For each color temperature setting, please repeat Steps 3 and 4 above but replace the x and y settings with the following values: a. 6500D: x = 313, y = 329 for both Dark and Bright Level Settings b. 9300K: x = 285, y = 295 for both Dark and Bright Level Settings c. 13800K: x = 260, y = 275 for both Dark and Bright Level Settings For these 3 Color Temperatures (6500D, 9300K and 13800K), adjust the Dark and Bright Levels to the following Y values: a. Dark level Y = 0.4±0.08 FL b. Bright level Y = 30±0.8 FL (6) Once all 4 Color Temperatures have been adjusted, skip through the RGB and AV Color Temperatures (using the FAV.SET key) and completely exit the Factory Adjustment Menu. 4. RGB Mode Color Temperature Adjustment procedure: (1) Turn on the Color Analyzer (Minolta, Model = CA-100) and reset the Color Analyzer. (2) Switch the PDP input to RGB mode and press the "Recall" key on the remote control to have the PDP set recalled back to default factory settings. (3) Set up the Video Pattern Generator (Chroma, Model = C2226) with the following settings: a. Timing: 640 x 480 @ 60Hz, b. Make sure the Output signal is Analog (RGB) Connect the PDP RGB input connector to the Chroma C-2226 RGB output connector. (4) Dark level and bright level center block definition: C. Dark level center block definition: Pattern set = Pattern name = 1-mosaic Color form = norm Background color = 0 Foreground color = 17 According to the C-2226's user manual, appendix analog-color: Normal Pen from Pen 17 = R: 102, G: 102, B: 102 102 (output amplifier)/1024 (total amplifier)=10%, therefore the 10% is the 10 IRE white output pattern. D. Bright level center block definition: Pattern set = Pattern name = 1-mosaic Color form = norm Background color = 0 Foreground color = 25 According to the C-2226's user manual, appendix analog-color: Normal Pen from Pen 25 = R: 614, G: 614, B: 614 614 (output amplifier)/1024 (total amplifier)=60%, therefore the 60% is the 60 IRE white output pattern. (5) Flatly place the Minolta Color Analyzer's Photo Detector in contact with the center of the PDP screen. (6) Set the Chroma C-2226 to a dark level center block signal (10 IRE). Enter the Factory Adjustment Menu using the same Key sequence specified above and then select the Color Temperature Adjustment option. Using the FAV.SET key skip through all the DVI Color Temperatures until you reach the 5400K RGB Color Temperature OSD.
3-4
FACTORY & ELECTRONIC ADJUSTMENT
VER1.0
(7) 5400K dark level center block adjustment procedure: A. Select G-BIAS and adjust the G-Bias value until Y = 0.5±0.08 FL B. Select R-BIAS and adjust the R-Bias value until x = 335±8 C. Select B-BIAS and adjust the B-Bias value until y = 343±8 D. Repeat steps A, B and C until the following final values are obtained: x = 335±8 y = 343±8 Y = 0.5±0.08 FL (8) 5400K bright level center block adjustment procedure: (Please set the Chroma C-2226 DVI bright level center block signal to 60 IRE) A. Select G-GAIN and adjust the G-GAIN value until Y = 30±0.8 FL B. Select R-GAIN and adjust the R-GAIN value until x = 335±8 C. Select B-GAIN and adjust the B-GAIN value until y = 343±8 D. Repeat steps A, B and C until the following final values are obtained: x = 335±8 y = 343±8 Y = 30±0.8 FL (9) Upon completion of Steps 7 and 8 above, press the FAV.SET key for the next Color Temperature setting (54006500D930013800). For each color temperature setting, please repeat Steps 7 and 8 above but replace the x and y settings with the following values: a. 6500D: x = 313, y = 329 for both Dark and Bright Level Settings b. 9300K: x = 285, y = 295 for both Dark and Bright Level Settings c. 13800K: x = 260, y = 275 for both Dark and Bright Level Settings For these 3 Color Temperatures (6500D, 9300K and 13800K), adjust the Dark and Bright Levels to the following Y values: a. Dark level Y = 0.5±0.08 FL b. Bright level Y = 30±0.8 FL (10) Once all 4 Color Temperatures have been adjusted, skip through the AV Color Temperatures and completely exit the Factory Adjustment Menu. 5. AV Mode Color Temperature Adjustment procedure: (1) Turn on the Color Analyzer (Minolta, Model = CA-100) and reset the Color Analyzer. (2) Switch the PDP input to AV1 mode and press the "Recall" key on the remote control to have the PDP set recalled back to default factory settings. (3) Using a Pattern Generator (ie. SENCORE VP-300 Multimedia Video Generator) set the dark level and bright level center block with the following settings: A. Dark Level Center block definition: a. Signal Type: NTSC/PAL b. Format: NTSC c. Pattern = WINDOW 1 14 IRE B. Bright Level Center block definition: a. Signal Type: NTSC/PAL b. Format: NTSC c. Pattern = WINDOW 2 60 IRE (4) Connect the PDP AV1 input to the VP-300 Composite output connector. (5) Flatly place the Minolta Color Analyzer's Photo Detector in contact with the center of the PDP screen. (6) Set the VP-300 to send a dark level center block signal (14 IRE). Enter the Factory Adjustment Menu using the same Key sequence specified above and then select the Color Temperature Adjustment option. Using the FAV.SET key skip through all the DVI and RGB Color Temperatures until you reach the 5400K AV Color Temperature OSD.
3-5
FACTORY & ELECTRONIC ADJUSTMENT
(7)
VER1.0
5400K dark level center block adjustment procedure: A. Select G-BIAS and adjust the G-Bias value until Y = 1.2±0.1 FL. B. Select R-BIAS and adjust the R-Bias value until x = 335±10 C. Select B-BIAS and adjust the B-Bias value until y = 343±10 D. Repeat steps A, B and C until the following final values are obtained: x = 335±10 y = 343±10 Y = 1.2±0.1 FL (8) 5400K bright level center block adjustment procedure: (Please set the VP-300 bright level center block signal to 60 IRE) A. Select G-GAIN and adjust the G-GAIN value until Y = 30±1 FL B. Select R-GAIN and adjust the R-GAIN value until x = 335±10 C. Select B-GAIN and adjust the B-GAIN value until y = 343±10 D. Repeat steps A, B and C until the following final values are obtained: x = 335±10 y = 343±10 Y = 30±1 FL (9) Upon completion of Steps 7 and 8 above, press the FAV.SET key for the next Color Temperature setting (54006500D930013800). For each color temperature setting, please repeat Steps 7 and 8 above but replace the x, y and Y values with the following values: a. 6500D: x = 313, y = 329 for both Dark and Bright Level Settings b. 9300K: x = 285, y = 295 for both Dark and Bright Level Settings c. 13800K: x = 260, y = 275 for both Dark and Bright Level Settings For these 3 Color Temperatures (6500D, 9300K and 13800K), adjust the Dark and Bright Levels to the following Y values: a. Dark level Y = 1.2±0.1 FL b. Bright level Y = 30±1 FL Once all 4 Color Temperatures have been set you will automatically exit the Color Temperature Adjustment. Once you exit the Color Temperature Adjustment proceed on by completely exiting the Factory Adjustment Menu.
3-6
BLOCK DIAGRAM
VER1.0
Y Amp Board-Upper
AV Module Board(with JP2 Tuner) Pin[1:32] Assy 5
JP1 Pin[1:32]
PDP Socket Diagram
JA2 Pin[1:10] JA1 Pin[1:12]
Audio Amplifier Board Ass'y 3
Pin[1:31]
12
J1 Pin[1:31]
Image Board Ass'y
J14 Pin[1:6] JP4 PinA[1:48]
1 PANEL Power Supply Ass'y 8
SA CON8011
(L VDS)
Interface Board- Y Ass'y
(5 V,SB DET )
J21 Pin[1:7]
6
J15
Pin[1:48]
(2 4 V,9 V)
JP5
J12 Pin[1:10]
Pin[7:13]
Y Amp Board-Lower
Pin[1:4]
(A ud io S ign a l)
J11 Pin[1:12]
(9 V)
J25 Pin[1:3]
Front Button Control Board Assy 4
Pin[1:6] JA3
(A ud io DC,S up pl y)
J5 Pin[1:6]
AUDIO CON8009 Pin[1:7] Pin[1:2]
(5 V)
(K ey)
Power SW
13
AC Master power swith Board 2 AC IN SW
AC OUT
Logic F-Buffer 14 9 Power Input Module Assy
Logic E-Buffer
11
AC PLUG
Pa n el 's B oa rd A ssem b ly SA M PO Bo ard A sse m b ly
4-1
10
Pin[1:6]
Interface Board- Z Ass'y
LA03
Logic Board Ass'y 7
BLOCK DIAGRAM
Image Board Socket Data
Im age Board Im age Board As s 'y
Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 J1 (40 Pin) GND NC RARA+ GND GND RBRB+ GND GND RCRC+ GND GND RCLKRCLK+ GND GND RDRD+ GND GND GND GND NC GND NC GND NC GND NC NC NC NC NC NC NC NC NC NC J14 (6 Pin) +5VSB DGND DGND 5V1 SB DGND J15 (4 Pin) J21 (7 Pin) VGND +9VT NC VGND DGND NC +24V +9V +24V GND GND J25 (3 Pin) +5VA VGND VGND
VER1.0
Panel Im age Board AV Module Board Im age Board AV Module Board Content
JP5 (48 Pi n) A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 JP2 (48 Pi n) A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 +9VT DGND NC DGND SCL2 DGND SDA2 DGND NC DGND T V_R DGND T V_L DGND AFT _T UN T UN_DET n DVI_L DVI_R AGND L_OUT R_OUT SUB_WFR PWR_CT L AGND AGND AGND AGND AGND AGND D_CT L RESET Q SD AS_M P AS_SP RST _DPT V SV2_SW V2B_DET n YUVn_RGB 15Kn_M P 15Kn_SP SB5V T DO T DI NC NC TMS DGND T CK
Im age Board AV Module Board Im age Board AV Module Board Content
JP5 (48 Pi n) A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 JP2 (48 Pi n) A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 COM POSIT E VGND S2_Y S2_C VGND Y1 PB1_CB1 PR1_CR1 VGND Y2 PB2_CB2 PR2_CR2 VGND AVB_DET n TV VGND AV1_L AV1_R AGND S2_L S2_R AGND YUV1_L YUV1_R AGND YUV2_L YUV2_R AGND RGB_L RGB_R AGND AGND PCn_M PU PCSCS PCSI PCSCLK SSO DGND P5V SCL2 SDA2 DGND SCL_SP SDA_SP DGND SCL2_33 SDA2_33 DGND
Im age Board Im age Board
J11 (12 Pin) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12
Audio Am plifier Board Content
24V 24V DGND SB5V DGND AO_SEL SDA2 SCL2 A_M UT En SURR1 SURR2 DGND
Audio Am plifier Board
JA1 (12 Pi n) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12
Im age Board Im age Board
J12 (10 Pin) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10
Audio Am plifier Board Content
L_IN R_IN AGND L_OUT R_OUT AGND SUB_WFR SPK_CT L PWR_CT L NC JA2 (10 Pi n) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10
Audio Am plifier Board
Im age Board Front Button Control Board Front Button Control Im age Board Content Board
J5 (6 Pin) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 JA3 (6 Pin) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 RC_OUT SW_OUT ON_LED SB_LED DGND SB5V
4-2
BLOCK DIAGRAM
Image Board Signal Block Diagram
SDRAM
(PAGE4)
VER1.0
TV AV S-VIDEO
TA8551CH AV SWITCH IC1
VIDEO Y C
6630/6730 MAIN Video Processor U45
(PAGE3)
RGB IN
RGB OUT
SDRAM
(PAGE2)
VIDEO Y C
6630/6730 SUB Video Porcessor U46
(PAGE5)
(PAGE12)
YUV SCALE IC MULTIPLEX SWITCH U34 AD Converter U29
(PAGE8) (PAGE7)
YCBCR SDRAM
(PAGE6)
C711/C713 U23
(PAGE11)
LVDS TRANSMITTER
(PAGE14)
P A N E L
YCBCR/YPBPR R,G,B Y1/CB/CR Y1/PB/PR MULTIPLEX SWITCH IC3 YCBCR/YPBPR MULTIPLEX SWITCH IC2 SIL161 DVI U32
(PAGE10) (PAGE13)
Clock Generator 9161A(PLL)
TA1276 Color Space Conveter U43 CPU U4 MULTIPLEX SWITCH Y2/CB/CR Y2/PB/PR IC7
(PAGE9)
DVI IN
RS232
(PAGE1)
4-3
BLOCK DIAGRAM
Image board Power Block Diagram
SB5V (USB 5V, SB5V_ M , SB5 V_IO, SB5V_ CPU) +9VT +5VSB J14 1 2 3 4 5 6 D43 SB5V_V R376 SB5V_VO J21 1 2 3 4 5 6 7
IC9
VER1.0
P9V (+9V) P5V_COLOR
+24V
P24V
+5V1
U63
V33SB USB3V V33 (VDD33) L13 VCCPLL VCCBF L17
U13
P5V (5 V_OSD)
U61
V33P L15
U62
VIP711
CON8009 1 2 3 4 5 6 7 8 9
+5VA
A5V
J25 1 2 3
U60
V33TMP (VDRAM ) VCC3 (VCC3_M ) VCCA3 V33ADC V33PLL CON8011 1 2 3 4 5 6 7 8 9 10 11 12 13
VDDM 5VDDA
U56
U52
+9V J15 1 2 3 4
U31
U28
REG_5V 5VDDD 5VDDM1 REG_5V_S
U53 U54
VADC3 V25_MP J25 VCCA3_S VADC3_S VCC3_S (VCC3_M _S ) V25_SP 1 2 3
U58
+5VA
A5V
U55
U57
U59
4-4
BLOCK DIAGRAM
VER1.0
PDP Sound Block Diagram
ICS1 LPF
ICS2 M UT E PAGE2
SUB_WOOFER OUT PUT
FROM AV SELECT OR
Q1/Q2 INPUT BUFFER
ICA1 /ICA2 M UT E
AV_ OUT PUT
ICR1 SRS SURROUND PROCESSOR
ICA3 FIXED/VARIBLE OUT PUT SELECT OR Q8/Q9 /Q1 1 M UT E
IC1 BBE & SOUND PROCESSOR
U1 BUFFER AM PLIFIER
IC2 M AIN POWER AM PLIFIER
INSIDE SPEAKER
PAGE1
DPWB1 13 72 -1G-S-
4-5
BLOCK DIAGRAM
Tuner Signal Block Diagram
VER1.0
9V
POWER BLOCK 7809 IC201 9V_T
JP 2 NE 555 IC241 SCL2 FROM IM AGE BOA RD CP U SDA2 5V 7805 IC202 2SC2482 Q241
31V T V _L OUT UP C 1854A CT T U201 RF M ODULE T U201 PIF M ODULE AUDIO OUT MTS IC203 T V _R OUT VIDE O OUT
DPWB11396-1G-T-
4-6
Trouble Shooting Guides No Power
VER1.0
SET POWER ON
AC Master Power Switch Board (DPWB11398-1G---) Check
G
AC Filter (LJ92-00579A) Check
NG Replace AC Filter (LJ92-00579A) Check
G
OK Main Power (LJ44-00025A) Check
NG Replace Main Power (LJ44-00025A) Check
OK
5-1
Trouble Shooting Guides No Picture
VER1.0
No Picture
AV Module Board (with Tuner) (DPWB11396-1G-T-) Check
NG Replace AV Module Board (with Tuner) (DPWB11396-1G-T-) Check
G
Image Board (DPWB11393-1GGW S) Check
OK NG
G
Replace Image Board (DPWB11393-1GGWS) Check
PDP Panel Module (VVEPP42SD001F--) Check
OK NG
Replace PDP Panel Module (VVEPP42SD001F--) Check
OK
5-2
Trouble Shooting Guides Vertical Line Fail
VER1.0
Vertical Line Fail
X Drive (LJ92-00596C) Check
NG Replace X Drive (LJ92-00596C) Check
G
OK PDP Panel Module Assembly (VVEPP42SD001F--) Check
NG
Replace PDP Panel Module Assembly (VVEPP42SD001F--) Check
OK
5-3
Trouble Shooting Guides Horizontal Line Fail
VER1.0
Horizontal Line Fail
Y Drive (LJ92-00597C) Check
NG Replace Y Drive (LJ92-00597C) Check
G
Y-Buffer (Upper) (LJ92-00570A) Check Y-Buffer (Lower) (LJ92-00571A) Check
OK NG Replace Y-Buffer (Upper) (LJ92-00570A) Check Y-Buffer (Lower) (LJ92-00571A) Check
G
OK PDP Panel Module Assembly (VVEPP42SD001F--) Check
NG Replace PDP Panel Assembly (VEPP42SD001F--) Check
OK
5-4
Trouble Shooting Guides No Remote Control
VER1.0
SET POWER ON
Remote Control
NG Replace Battery Replace BRC-241
G
OK Front Button Control Board (DPWB11372-1G-K2)
OK
NG Replace Front Button Control Board (DPWB11372-1G-K2) Check
Check
G
OK Image Board (DPWB11393-1GG WS)Check
NG Replace Image Board (DPWB11393-1GGWS) Check
OK
5-5
Trouble Shooting Guides Front Button Fail
VER1.0
SET POWER ON
Front Button Control Board DPWB11372-1G-K2 Replace Front Button Control Board
N
Y
DPWB11372-1G-K2
OK
Image Board DPWB11393-1GGWS
N
Replace Image Board DPWB11393-1GGWS
OK
5-6
B.O.M of Board Assembly Module Breakdown
Model Name: GTW-P42M203
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Image Board AC Master Power Switch Board Audio Amplifier Board Front Button Control Board AV w/ Tuner Module Board Logic Board X Drive Y Drive Logic E - Buffer Logic F - Buffer Y-Buffer (Upper) Y-Buffer (Lower) Main Power AC Filter PDP Panel Module Glass Filter Speaker Front Bezel Rear Cover Module Supplier Supplier's Ass'y Part # Sampo Sampo Sampo Sampo Sampo Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Samsung Sampo Sampo Sampo Sampo DPWB11393-1GGWS DPWB11398-1G--DPWB11372-1G-SDPWB11372-1G-K2 DPWB11396-1G-TLJ92-00621A LJ92-00596C LJ92-00597C LJ92-00600A LJ92-00601A LJ92-00570A LJ92-00571A LJ44-00025A LJ92-00579A VVEPP42SD001F-PGLS-0013-1---RSPK1L068-1CFIDMSKP0124-1F-AL GCABB0297-1P--I DSTN-0009-1F--A Quantity Per Final Assembly 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 TSMT TSMT TSMT TSMT TSMT Danam Asahi Glass Corporation In Hana Industrial Co. Ltd. Cheng Fa Plastic Mfg Co., Ltd. Yund Cheng Industrial Co., Ltd. Yo Tai Plastic Industrial Co., Ltd. Sub-Con Name Sub-Con Location Taiwan Taiwan Taiwan Taiwan Taiwan Korea Japan Taiwan Taiwan Taiwan Taiwan
VER1.0
Current Revision Level S11393-05-1A1 OR A11372-02-100 K2 T11396-00-100 A4 A1 A1 A1 A1 A1 A1 A1 0.2 V1 OR OR AL I A
Plasma Stand Assembly- Leg Type Sampo
Remark: 1. Please refer to each "Module BOM (#)" Tab for each module accroding to the No. indicated in the first column. 2. OR: Original Revision 6-1
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly 1 2 Supplier Name Ref Designator
QCNCP1623-140-A QCNCS1680-1---QCNWT1285-1001QCNWT128A-1001QPWB11393-1G-5QSOCD1550-115-QSOCD1553-109-QSOCD1555-124-QSOCI1177-108-QSOCI1514-132-S RCHO-1022D8---RCHOL1020-1100RCORA1021-1---U RCORA1047-1---A RCORA1048-1121A RCRSL1185-1---A RCRSL1187-1---A RNWR-0028CM103A RNWR-0028CM220A RNWR-0028CM330A
Connector Connector
40PIN 48pin
Chia-Soon Electronics Co., Ltd. Oupiin Enterprise Co., Ltd.
JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD
J1 JP4 JP5
1 1
PCB Bareboard Socket Socket DVI Socket IC Socket IC Socket Choke Choke Bead core Bead core Bead core Crystal Crystal Network Resister Network Resister Network Resister Image Board 1 2 1 1 3 1 1 5 1 3 4 1 2 9 13 24
24PIN 8Pin 32Pin 330uH 10uH 0.45uH 120/100MHz 120/100MHz 16MHz 14.318MHz 10K ohm 22 ohm 33 ohm
EISD Enterprise Co., Ltd. Chia-Soon Electronics Co., Ltd. Chia-Soon Electronics Co., Ltd. MOLEX Suyin Corporation Chia-Soon Electronics Co., Ltd. Top-Nation Electronic Factory Taiwan Sumida Electronics Inc. Murata Mfg. Co., Ltd. Walsin Technology Corp. Walsin Technology Corp. KDS Taiwan Electronics Corp. KDS Taiwan Electronics Corp. Yageo Corporation Yageo Corporation Yageo Corporation
PCB S1 S2 P1 J9 U33 Socket U35 Socket U7 Socket U3 SOCKET L24 L25 L26 L27 L28 L30 L29 F21 F23 F26 L21 L22 L23 R87 Y1 Y3 YD1 RP1 RP2 RP3 RP5 RP8 RP9 RP12 RP43 RP45 RND1 RND2 RND3 RND4 RND5 RND6 RP35 RP36 RP37 RP38 RP39 RP40 RP41 RP10 RP11 RP13 RP14 RP15 RP16 RP17 RP18 RP19 RP20 RP21 RP22 RP23 RP24 RP25 RP26 RP27 RP28 RP29 RP30 RP31 RP32 RP33 RP34
TLABD1145-1B--Barcode label TLABD1149-1B--Label VCEABN1CG106MNA Capacity,Aluminum Elect.
10uF
16V
±20%
1 1 62
Diing Yih Enterprise Co., Ltd. Trim International Inc. Matsushita Electric Co., Ltd.
C9 C10 C13 C14 C15 C27 C43 C58 C99 C115 C158 C185 C214 C219 C220 C221 C222 C223 C230 C231 C246 C251 C253 C258 C271 C310 C312 C322 C324 C391 C399 C400 C401 C405 C406 C407 C409 C415 CD8 CD17 CD22 CD36 CD40 CD45 CD47 CD49 CD51 CD53 CD67 CD71 CDS8 CDS17 CDS22 CDS36 CDS40 CDS45 CDS47 CDS49 CDS51 CDS53 CDS67 CDS71
6-2
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly ±20% 22 Supplier Name Ref Designator
VCEABN1CG107MNA Capacity,Aluminum Elect.
100uF
16V
Matsushita Electric Co., Ltd.
C86 C124 C211 C224 C226 C237 C241 C259 C266 C291 C295 C299 C309 C311 C321 C323 C338 C343 C346 C349 C381 C412 C65 C71 C72 C73 C160 C194 C203 C204 C268 C277 CD16 CD23 CD69 CD82 CD84 CD87 CD89 CD92 CD94 CD97 CD99 CDS16 CDS23 CDS69 CDS82 CDS84 CDS87 CDS89 CDS92 CDS94 CDS97 CDSA1 C197 C202 C210 C337 C342 C345 C348 C411 CD18 CDS18 C269 C287 C37 C55 C59 C162 C165 C167 C171 C172 C173 C175 C179 C190 C191 C193 C195 C215 C217 C229 C233 C234 C238 C239 C240 C249 C256 C284 C410 C417 CD9 CD13 CD15 CDS9 CDS13 CDS15 C333 C335 C31 C34 C192 C236 C275 C283 C297 CD12 CD14 CDS12 CDS14 C288 C4 C183 C184 C186 C187 C188 C189 C198 C199 C205 C206 C207 C208 C248 C273 C274 C276 C281 C282 C286 C384 C385 C386 C389 C216 C6 C7 CD38 CD39 CD42 CD43 CD44 CDS38 CDS39 CDS42 CDS44 C29 C30 C140 C153 C154 C155 C156 C166 C169 C176 C180 C181 C182 C232 C245 C265 C301 C308 C341 CD6 CD10 CD21 CD25 CD37 CD41 CDS6 CDS10 CDS21 CDS25 CDS37 CDS41 C22 C51 C52 C16 C17 C18 C19 C20 C375 C35 C36 C306 C307 C383 CD3 CD4 C300 C404 C414 C2 C3 C303 C144 C145 C146 C147 C148 C149 C150 C151
VCEABN1CG226MNA Capacity,Aluminum Elect.
22uF
16V
±20%
32
Matsushita Electric Co., Ltd.
VCEABN1CG227MNA Capacity,Aluminum Elect. VCEABN1CG337MNA Capacity,Aluminum Elect. VCEABN1CG476MNA Capacity,Aluminum Elect.
220uF 330uF 47uF
16V 16V 16V
±20% ±20% ±20%
10 2 34
Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd.
VCEABN1EG227MNA VCEABN1HG105MNA VCEABN1HG224MNA VCEABN1HG225MNA
Capacity,Aluminum Elect. Capacity,Aluminum Elect. Capacity,Aluminum Elect. Capacity,Aluminum Elect.
220uF 1uF 0.22uF 2.2uF
25V 50V 50V 50V
±20% ±20% ±20% ±20%
2 11 1 20
Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd.
VCEABN1VG475MNA VCEACU1HG476MNP VCICHN1HH100J-A VCICHN1HH101J-A
Capacity,Aluminum Elect. Capacity,Aluminum Elect. Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic
4.7uF 47uF 10PF 100PF
35V 50V 50V 50V
±20% ±20% ±5% ±5%
4 1 11 31
Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Yageo Corporation Yageo Corporation
VCICHN1HH120J-A VCICHN1HH121J-A VCICHN1HH181J-A VCICHN1HH200J-A VCICHN1HH220J-A VCICHN1HH330J-A VCICHN1HH331J-A
Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic
12PF 120PF 180PF 20PF 22PF 33PF 330PF
50V 50V 50V 50V 50V 50V 50V
±5% ±5% ±5% ±5% ±5% ±5% ±5%
3 6 5 2 3 3 8
Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation
6-3
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly ±5% 25 Supplier Name Ref Designator
VCICHN1HH470J-A
Capacity,Temp. Comp. Ceramic
47PF
50V
Yageo Corporation
C305 C351 C352 C353 C354 C355 C356 C357 C358 C359 C360 C361 C362 C363 C364 C365 C366 C367 C368 C369 C370 C371 C372 C373 C374 C177 C387 C54 C200 C334 C380 C402 C403 C1 C5 C8 C11 C12 C21 C23 C24 C25 C28 C33 C38 C39 C40 C50 C56 C57 C60 C61 C62 C63 C64 C66 C67 C68 C69 C70 C74 C75 C76 C77 C78 C79 C80 C81 C82 C83 C84 C85 C87 C88 C89 C90 C91 C92 C93 C94 C95 C96 C97 C98 C100 C101 C102 C103 C104 C105 C107 C111 C114 C116 C117 C118 C119 C120 C121 C122 C123 C125 C127 C129 C130 C131 C132 C133 C134 C135 C136 C137 C138 C139 C157 C161 C178 C212 C213 C267 C278 C279 C280 C304 C313 C315 C317 C319 C325 C327 C329 C331 C336 C339 C344 C347 C350 C390 C392 C393 C394 C395 C396 C397 C398 C408 C413 C419 C421 C423 C425 C427 CD5 CD7 CD11 CD24 CD26 CD27 CD28 CD29 CD32 CD33 CD34 CD35 CD46 CD48 CD50 CD52 CD54 CD55 CD56 CD57 CD58 CD59 CD60 CD68 CD70 CD72 CD85 CD86 CD90 CD91 CD95 CD96 CD100 CD101 CDS5 CDS7 CDS11 CDS24 CDS26 CDS27 CDS28 CDS29 CDS32 CDS33 CDS34 CDS35 CDS46 CDS48 CDS50 CDS52 CDS54 CDS55 CDS56 CDS57 CDS58 CDS59 CDS60 CDS68 CDS70 CDS72 CDS85 CDS86 CDS90 CDS91 CDS95 CDS96 CDS99 CDSB2 C113 C108 C109 C110 C388 C376 C377 C378 C379 C430 CD30 CD31 CD73 CD74 CD75 CD76 CD77 CD78 CD79 CD80 CD81 CDS30 CDS31 CDS73 CDS74 CDS75 CDS76 CDS77 CDS78 CDS79 CDS80 CDS81
VCICHN1HH471J-A VCICHN1HH561J-A VCICHN1HH680J-A VCLFCN1HY224M-A VCLFHN1EY104Z-A
Capacity,Temp. Comp. Ceramic Capacity,Temp. Comp. Ceramic Capacity,High Diel. Ceramic Capacity,High Diel. Ceramic Capacity,High Diel. Ceramic
470PF 560PF 68PF 0.22uF 0.1uF
50V 50V 50V 50V 25V
±5% ±5% ±5% ±20% +80%~-20%
1 1 1 5 187
Yageo Corporation Samsung Yageo Corporation Yageo Corporation Yageo Corporation
VCLRHN1CB393K-A VCLRHN1CB473K-A VCLRHN1CB683K-A VCLRHN1HB102K-A
Capacity,High Diel. Ceramic Capacity,High Diel. Ceramic Capacity,High Diel. Ceramic Capacity,High Diel. Ceramic
0.039uF 0.047uF 0.068uF 1000PF
16V 16V 16V 50V
±10% ±10% ±10% ±10%
1 3 1 27
Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation
6-4
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly ±10% 67 Supplier Name Ref Designator
VCLRHN1HB103K-A Capacity,High Diel. Ceramic
0.01uF
50V
Yageo Corporation
C106 C126 C128 C159 C163 C164 C168 C170 C174 C196 C201 C209 C218 C225 C228 C235 C247 C260 C270 C272 C290 C292 C293 C294 C298 C314 C316 C318 C320 C326 C328 C330 C332 C340 C382 CD61 CD62 CD63 CD64 CD65 CD66 CD102 CD103 CD104 CD105 CD106 CD107 CD108 CD109 CD110 CD111 CDS61 CDS62 CDS63 CDS64 CDS65 CDS66 CDSA2 CDSA3 CDSA4 CDSA5 CDSA6 CDSA7 CDSA8 CDSA9 CDSB0 CDSB1 CD1 CD2 CDS1 CDS2 C112 J25 J15 J14 J21 J5 J12 J11 J26 J27 J23 J24 C289 C141 C142 C143 C152 F1 F2 F5 F6 F7 F8 F9 F10 F11 F12 F13 F15 F17 F18 F20 F22 F24 L1 L2 L3 L4 L6 L7 L9 L10 L11 L12 L13 L15 L16 L17 L18 L19 L31 L33 L36 L38 L50 LD1 LD2 LD3 LD4 LD5 LD6 LD7 LD8 LD11 LD12 LD13 LD14 LD18 LD22 LD26 LDS1 LDS2 LDS3 LDS4 LDS5 LDS6 LDS7 LDS8 LDS11 LDS12 LDS13 LDS14 LDS15 LDS17 LDS19 F3 F4 R49 R91 R96 R98 R101 R123 R139 R229 R236 R246 R258 R259 R260 R261 R263 R272 R320 R340 R341 R342 R344 R345 R385 R389 R391 R393 R402 R404 R408 RD1 RD2 RD19 RD28 RD35 RDS1 RDS2 RDS19 RDS22 RDS28 RDS35 R22 R23 R38 R40 R175 R187 R189 R192 R193 R230 R235 R254 R257 R376 R377 R378 R379 R380 R381 R383
VCLRHN1HB222K-A VCLRHN1HB392K-A VCNCP0053-JJSTVCNCP0054-JJSTVCNCP0056-JJSTVCNCP0057-JJSTVCNCP0316-EJSTVCNCP031A-EJSTVCNCP031C-EJSTVCNCT1285-BJSTA VCNCT128A-BJSTA VCPELU1HG222J-P VCTABN1AB106M-A VRMBNV8--000J-A
Capacity,High Diel. Ceramic Capacity,High Diel. Ceramic Connector Connector Connector Connector Connector Connector Connector Connector Connector Capacity,Polyester Film Capacity,tantalum Resiser,Metal Film
2200PF 3900PF 3 Pin 4 Pin 6 Pin 7 Pin 6 Pin 10 Pin 12 Pin 5 PIN 10PIN 2200PF 10uF 0
50V 50V
±10% ±10%
50V 10V 1/8W
±5% ±20% ±5%
4 1 1 1 1 1 1 1 1 2 2 1 4 68
Yageo Corporation Yageo Corporation
JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD JST ELECTRONIC PRODUCTS MFG.CO.,LTD
Mylar Electronics Co., Ltd. Energie Electronic Co., Ltd. Yageo Corporation
VRMBNV8--181J-A VRMHNVG--000J-A
Resiser,Metal Film Resiser,Metal Film
180 0
1/8W 1/16W
±5% ±5%
2 40
Yageo Corporation Yageo Corporation
VRMHNVG--100J-A
Resiser,Metal Film
10
1/16W
±5%
20
Yageo Corporation
6-5
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly ±5% ±5% ±5% 16 17 30 Supplier Name Ref Designator
VRMHNVG--101J-A VRMHNVG--102J-A VRMHNVG--103J-A
Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film
100 1K 10K
1/16W 1/16W 1/16W
Yageo Corporation Yageo Corporation Yageo Corporation
R62 R65 R66 R67 R145 R150 R154 R159 R160 R163 R195 R198 R200 R273 R281 R286 R58 R168 R170 R205 R225 R239 R256 R270 R271 R279 R303 R306 R308 R327 R335 R337 R338 R1 R5 R36 R37 R39 R89 R92 R93 R106 R119 R120 R125 R134 R136 R138 R142 R144 R156 R161 R162 R178 R184 R265 R287 R313 R339 RD13 RD23 RDS13 RDS23 R6 R266 R310 R309 R372 R373 R374 R148 R151 R155 R164 R165 R166 R282 R295 R355 R356 R357 R289 R291 R305 R397 R398 R400 R401 R243 R300 R71 R211 R217 R220 R223 R386 R208 R209 R213 R215 R218 R219 R221 R222 R276 R285 R241 R247 R269 R292 R387 R262 R264 R275 R118 R232 R237 R248 R54 R86 R382 RDS3 RDS4 RDS5 RDS6 RDS12 R202 R224 R316 R369 R370 R371 RD16 RD20 RDS16 RDS20 R288 R27 R30 R34 R35 R297 R301 R311 R250 R72 R74 R388 R268 RD10 RDS10 R283 R284
VRMHNVG--104J-A VRMHNVG--105J-A VRMHNVG--121J-A VRMHNVG--122J-A VRMHNVG--123J-A VRMHNVG-1240F-A VRMHNVG--124J-A VRMHNVG--132J-A VRMHNVG--151J-A VRMHNVG--152J-A VRMHNVG--181J-A VRMHNVG--182J-A VRMHNVG--183J-A VRMHNVG--202J-A VRMHNVG--220J-A VRMHNVG--221J-A VRMHNVG--222J-A VRMHNVG--223J-A VRMHNVG--224J-A VRMHNVG--270J-A VRMHNVG--272J-A VRMHNVG--273J-A VRMHNVG--303J-A
Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film
100K 1M 120 1.2K 12K 124 120K 1.3K 150 1.5K 180 1.8K 18K 2K 22 220 2.2K 22K 220K 27 2.7K 27K 30K
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
±5% ±5% ±5% ±5% ±5% ±1% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5%
3 1 3 11 3 4 2 1 5 10 4 1 3 4 8 10 1 7 1 3 1 2 2
Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation
6-6
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly ±5% 39 Supplier Name Ref Designator
VRMHNVG--330J-A
Resiser,Metal Film
33
1/16W
Yageo Corporation
R10 R12 R18 R19 R20 R21 R24 R31 R33 R68 R69 R77 R78 R79 R80 R81 R83 R105 R108 R111 R112 R113 R114 R121 R122 R317 R318 RD29 RD30 RD31 RD32 RD33 RD34 RDS29 RDS30 RDS31 RDS32 RDS33 RDS34 R7 R15 R16 R17 R109 R171 R173 R176 R179 R181 R185 R194 R199 R203 R206 R210 R214 R267 R277 R312 R323 R329 R298 R307 RD3 RD4 RD5 R116 R293 R274 R299 R8 R9 R13 R59 R60 R61 R63 R182 R188 R190 R197 R315 RD14 R28 R32 R172 R174 R177 R180 R183 R186 R191 R196 R201 R204 R207 R212 R216 R296 R331 R153 R82 R115 R117 R157 RD9 RDS9 R25 R29 R278 R328 R88 R129 R333 R334 R336 R290 R332 R102 R103 R104 R146 R147 R149 R167 R169 R358 R359 R360 R361 R362 R363 R364 R365 R366 R367 R368 R375 R280 R302 D4 D8 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D26 D28 D29 D30 D31 D32 D1 D2 D3 D25 D34 D35 D36 D37 D38 D39 D40 D41 D42 D43 D45 D50 D51 D52 D54 D55 D57 D58
VRMHNVG--332J-A VRMHNVG--333J-A VRMHNVG--390J-A VRMHNVG--391J-A VRMHNVG--392J-A VRMHNVG--393J-A VRMHNVG--470J-A VRMHNVG--472J-A VRMHNVG--473J-A VRMHNVG--474J-A VRMHNVG--4R7J-A VRMHNVG--561J-A VRMHNVG--562J-A VRMHNVG--563J-A VRMHNVG--682J-A VRMHNVG--750J-A VRMHNVG--821J-A VRMHNVG--823J-A VSDBAV99------A VSDRLS4148----A VSI29C020CP90BS VSI5160L16-7--D
Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Resiser,Metal Film Diode Diode IC- 256K CMOS Flash Memory IC- SDRAM
3.3K 33K 39 390 3.9K 39K 47 4.7K 47K 470K 4.7 560 5.6K 56K 6.8K 75 820 82K BAV99 RLS4148 29C020CP90BS 5160L16-7
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5%
22 2 3 1 1 2 7 6 17 1 4 2 4 5 2 20 1 1 22 22 1 3
Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Philips Semiconductors ROHM CO.,LTD
WINBOND ELECTRONICS CORP. U3
G-Link Technology
U25 U26 U27
6-7
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly 1 1 1 2 4 2 1 1 1 1 2 9 1 1 1 1 1 2 1 1 1 3 2 2 1 3 1 1 Supplier Name Ref Designator
VSI74HC221D---A VSI74HC4538D--A VSI74HCT04D---A VSI74LVC157---A VSI74LVC244ADBA VSI74LVT04----A VSI74LVT14----A VSI78M05A-----A VSIA5-32-10VC4D VSIAD9884AKS--D VSIAT24C21----VSIBA033------A VSIBA033LBSG--A VSIBA7657F----A VSIDS90C385---A VSIEM83010----VSIHD6413079F-D VSIHEF4053BT--A VSIHIN232CB-T-A VSIICS9161A---A VSIIP00C713---D VSILA7213-----VSILM1085ISX-3A VSILM1085ISX-AA VSIM24C16WBN6-VSIM52055FP---A VSIM52347FP---A VSIMTV130-----A
IC- Dual Non-Retriggerable Monostable Multivibrator with Reset IC- Dual Retriggerable Precision Monostable Multivibrator IC- Inverter IC- Multiplexer IC- Octal Buffer/Line Driver IC- Hex Inverter IC- Hex Inverter IC- 5 Voltage Regulator IC- In System Programmable High Density PLD IC- Analog Interface IC- EEPROM IC- Low Dropout 3.3 Voltage IC- 3.3 Voltage Regulator IC- Input Selector Switch IC- LVDS Transmitter IC- I/O Expander IC- CPU IC- Analogue IC- RS232 IC IC- Programmable Freq. IC IC- Color Image Enlargement Reduction LSI IC- Monolithiclinear IC- 3.3 Voltage Regulator IC- 2.5 Voltage Regulator IC- EEPROM IC- 3-Channel Analog Switch IC- Sync Signal Processor IC- OSD IC
74HC221D 74HC4538D 74HCT04D 74LVC157 74LVC244ADB 74LVT04 74LVT14 78M05A A5-32-10VC4 AD9884AKS AT24C21 BA033 BA033LBSG BA7657F DS90C385 EM83010 HD6413079F HEF4053BT HIN232CB ICS9161A IP00C713 LA7213 LM1085ISX-3 LM1085ISX-A M24C16WBN6 M52055FP M52347FP MTV130
Philips Semiconductors / Texas Instruments
IC12 IC11
Philips Semiconductors / Texas Instruments Philips Semiconductors / Texas Instruments Philips Semiconductors / Texas Instruments
U67 U15 U22 Philips Semiconductors / Texas Instruments U18 U19 U20 U21 Philips Semiconductors / Texas Instruments U6 U24 Philips Semiconductors / Texas Instruments U30 ST Microelectronics IC9 LATTICE SEMICONDUCTOR CORPORATION U1 ANALOG DEVICES ROHM CO.,LTD ROHM CO.,LTD ROHM CO.,LTD National Semiconductor EMC CORPORATION Hitachi SEMICONDUCTOR U29
ST Microelectronics / Atmel Corporation U33 U35
U31 U52 U53 U54 U55 U60 U61 U62 U63 U28 U34 U66 U8 U4 Philips Semiconductors / Texas Instruments IC13 U42 FAIRCHILDI SEMICONDUCTOR U12 INTEGRATED CIRCUIT SYSTEMS U16 I-CHIPS TECHNOLOGY INC. U23 SANYO SEMICONDUTORS NATIONAL SEMICONDUCTORS NATIONAL SEMICONDUCTORS ST Microelectronics
MUTSUBISHI ELECTRIC CORPORATION MUTSUBISHI ELECTRIC CORPORATION
MYSON TECHNOLOGY INC.
IC4 IC6 IC10 U56 U57 U58 U59 U7 IC2 IC3 IC7 U64 U11
6-8
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part #
VER1.0
Image Board Sampo DPWB11393-1GGWS S11393-05-1A1
Part Number Name Part Description Quantity per Assembly 2 1 1 4 1 1 3 1 30 4 6 1 Supplier Name Ref Designator
VSIPNLTVP6730-D VSIS80845ANUP-A VSISII161BCT--D VSISM84L512K--D VSITA1276AF---D VSITA8851CN---VST2SA1037KQ--A VST2SC1213C---P VST2SC2412KBQ-A VSTBSN20------A VSTDTC144EKA--A VSZRLZ7.5B----A
IC- Progressive IC- Voltage Detector IC- DVI Interface IC IC- SGRAM IC- Video/Chroma/Deflection IC- Audio/Video Switch Transistor Transistor Transistor Transistor Transistor Zener Diode
PNLTVP6730 S80845ANUP SII161BCT SM84L512K TA1276AF TA8851CN 2SA1037KQ 2SC1213C 2SC2412KBQ BSN20 DTC144EKA RLZ7.5B
Trident Technologies Inc. Seiko Instrunets Taiwan Inc. SILICON IMAGE SILICOM MAGIC CORP. TOSHIBA CORPORATION TOSHIBA CORPORATION ROHM CO.,LTD HITACHI SEMICONDUCTOR ROHM CO.,LTD Philips Semiconductors ROHM CO.,LTD ROHM CO.,LTD
U45 U46 U5 U32 U48 U49 U50 U51 U43 IC1 Q31 Q34 Q39 Q48 Q1 Q2 Q3 Q4 Q7 Q8 Q9 Q10 Q11 Q12 Q14 Q15 Q16 Q17 Q18 Q19 Q25 Q26 Q27 Q28 Q29 Q30 Q32 Q33 Q35 Q36 Q37 Q38 Q43 Q44 Q5 Q6 Q20 Q21 Q40 Q41 Q42 Q45 Q46 Q47 ZD1
6-9
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part # QPWB11398-1G--QCNCP1552-1---QCNCP1622-1----
VER1.0
AC Master Power Switch Board Sampo DPWB11398-1G--OR
Part Number Name PCB Bareboard Connector Connector Part Description POWER SWITCH B/O 3PIN 4PIN Quantity per Assembly 1 2 1 Supplier Name Ref Designator
Chien Wey Electronic Industrial Co., LPCB Chia-Soon Electronics Co., Ltd. AC IN, AC OUT Chia-Soon Electronics Co., Ltd. SW
6-10
B.O.M of Board Assembly Module Part Level BOM
Module Name: Supplier Name: Module P/N: Revision:
Part # PRDAA0116-1G--I PRDAA0140-1P--G QPWB11372-1G-2S RFILN1011-1---TLABD1145-1B--VCEACU1CG107MNP VCEACU1CG226MNP VCEACU1CG337MNP VCEABN1CG476MNA VCEACU1CG477MNP VCEACU1EG477MNP VCEACU1HG105MNP VCEACU1HG106MNP
VER1.0
Audio Amplifier Board Sampo DPWB11372-1G-SA11372-02-100
Part Number Name HEAT SINK IC2 USE U2 USE Heat Sink PCB Amp Output Filter Barcode label Aluminum Elect. Aluminum Elect. Aluminum Elect. Aluminum Elect. Aluminum Elect. Aluminum Elect. Aluminum Elect. Aluminum Elect. Part Description Quantity per Assembly 1 1 1 2 1 4 3 1 1 1 2 3 15 Supplier Name Base Strong Industrial Co., Ltd. Base Strong Industrial Co., Ltd. EISD Enterprise Co., Ltd. Murata Mfg. Co., Ltd. Diing Yih Enterprise Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Ref Designator
1000P/100V 100uF 22uF 330uF 47uF 470uF 470uF 1uF 10uF 16V 16V 16V 16V 16V 25V 50V 50V ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20%
PCB (AUDIO) F1 F2 C30 C31 C42 CR10 C1 C8 C14 C54 CS1 C28 C52 C59 C36 CR6 CR9 C3 C5 C7 C12 C62 C63 C65 C66 C67 C68 CR4 CR5 CR15 CS2 CS3 C16 C40 C2 C4 C64 CR1 C9 C11 C17 C18 C23 C24 C25 C33 C34 C37 C41 CR13 CR16 C53 C49 C71 C43 C6 C13 C51 C56 C72
VCEACU1HG224MNP VCEACU1HG225MNP VCEACU1HG475MNP
Aluminum Elect. Aluminum Elect. Aluminum Elect.
0.22uF 2.2uF 4.7uF
50V 50V 50V
±20% ±20% ±20%
2 4 13
Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd.
VCEACU1VG107MNP VCEACU1VG108MNP VCEACU1VG227MNP VCICHN1HH221JVCLFCN1HY224M-A
Aluminum Elect. Aluminum Elect. Aluminum Elect. Temp. Comp. Ceramic High Diel. Ceramic
100uF 1000uF 220uF 220PF 0.22uF
35V 35V 35V 50V 50V
±20% ±20% ±20% ±10% ±20% 6-11
1 2 1 2 3
Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Matsushita Electric Co., Ltd. Yageo Corporation Yageo Corporation
B.O.M of Board Assembly
Part # VCLFHN1AY105Z-A VCLFHN1EY104Z-A VCLRCN1CB224K-A VCLRCN1CB474K-A VCLRHN1CB104K-A VCLRHN1CB273K-A VCLRHN1CB333K-A VCLRHN1CB473K-A VCLRHN1HB102K-A VCLRHN1HB103K-A VCLRHN1HB153K-A VCLRHN1HB222K-A VCLRHN1HB332K-A VCLRHN1HB392K-A VCLRHN1HB471K-A VCLRHN1HB472K-A VCMECU1JG474J-P VCNCP0302-EJSTVCNCP030A-EJSTVCNCP030C-EJSTVCPELU1HG104J-P VCPELU1HG223J-P VL-DH120K0000-U VRCPT4--2R2J-U VRMHNVG--000J-A VRMHNVG--100J-A VRMHNVG--101J-A VRMHNVG--102J-A Part Number Name High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic High Diel. Ceramic Metal Ploy. Film Connector Connector Connector Polyester Film Polyester Film Peaking Coil Metel Film Metel Film Metel Film Metel Film Metel Film 1uF 0.1uF 0.22uF 0.47uF 0.1uF 0.027uF 0.033uF 0.047uF 1000PF 0.01uF 0.015uF 2200PF 3300PF 3900PF 470PF 4700PF 0.47uF 2 PIN 10 PIN 12 PIN 0.1uF 0.022uF 12uH 2.2 0 10 100 1K Part Description 10V 25V 16V 16V 50V 16V 16V 16V 50V 50V 50V 50V 50V 50V 50V 50V 63V +80%~-20% +80%~-20% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±10% ±5% Quantity per Assembly 1 2 2 6 8 1 2 1 2 3 1 3 2 2 1 3 1 2 1 1 1 2 1 1 1 1 2 1 Supplier Name Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Lipers Enterprise Co., Ltd. Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Yageo Corporation Mylar Elctronics Co., Ltd. Chia-Soon Electronics Co., Ltd. Chia-Soo