Text preview for : KV-29LS30_LS35.pdf.pdf part of SONY KV-29LS30_LS35 SERVICE MANUAL
Back to : KV-29LS30_LS35.part1.rar | Home
SERVICE MANUAL
MODEL
COMMANDER DEST CHASSIS NO.
FE-2 CHASSIS
MODEL
COMMANDER DEST CHASSIS NO.
KV-29LS30E KV-29LS30K KV-29LS30U
RM-887
ESP
SCC-Q53F-A
RM-887
OIRT
SCC-Q51G-A
RM-887
UK
SCC-Q52F-A
KV-29LS35B KV-29LS35E KV-29LS35K
RM-932
FR
SCC-Q54F-G
RM-932
ESP
SCC-Q53G-A
RM-932
OIRT
SCC-Q51H-A
RM-889
RM-887
RM-932
1
FE-2 SELF DIAGNOSTIC SOFTWARE
The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this method. Each time the software detects an error it is stored within the NVM. See Table 2.
Table 1
LED Code 00 01 02 03 04 05 06 07 08 09 10 11
How to enter into Table 2 1. Turn on the main power switch of the TV set and enter into the `Stanby Mode'. Press the following sequence of buttons on the Remote Commander.
Error Message No error Reserved OCP ( Over Current Protection ) Not Used No Ver tical Sync IKR Error at power on IIC bus clock and/or data lines low at power on NVM no IIC bus acknowledge at power on Not Used Tuner no acknowledge at power on Sound Processor Error Jungle controller 8 volts error
2.
i+
(ON SCREEN DISPLAY)
5
(DIGIT 5)
(VOLUME -) (TV)
3.
The following table will be displayed indicating the error count.
Flash Timing Example : e.g. error number 3 Table 2
StBy LED ON ON ON
ERROR MENU E0 2 E03 E04 E05 E06 E07 E08 E09 E1 0 E1 1 WORKING TIME HOURS MINUTES OCP OVP N/A VSYNC IKR IIC NVM JUNGLE TUNER SOUNDP 8V (0, 255) (0, 255) (0, 255) (0, 255) (0, 255) (0, 255) (0, 255) (0, 255) (0, 255) (0, 255) 0 0 0 0 0 0 0 0 0 0
OFF
OFF
2 11
Note: To clear the error count data press `80' on the Remote commander.
6
C Board Waveforms
C board Waveforms
TP1
10us/div
TP2
20us/div
TP3
20us/div
1.77 Vp-p (H)
20us/div
1.88 Vp-p (H)
TP4 TP4 TP5
20us/div
1.88 Vp-p (H)
TP6
20us/div
74 Vp-p (H)
TP7
20us/div
74 Vp-p (H)
74 Vp-p (H)
1.76 Vp-p (H)
IC Voltage Table
Ref No Pin No Voltage (V) 1 2 3 IC1701 5 7 8 9 3.1 2.1 3.0 5.5 131 123 124.6 IC1801 Ref No Pin No Voltage (V) 1 2 3 5 6 7 8 1 .3 1.3 1.4 4.1 4.1 7.0 8.0
C
28
[ R,G,B OUT ]
27
VM [ VELOCITY MODULATION ]
30
29
F2 [ AC FILTER, FUSE, SIRCS ]
32
H2 [ AV3 INPUT ]
31
KV-29LS30/35
[9-927-403-01]
A
36 37
[ POWER SUPPLY, DEFLECTION, AUDIO AMPLIFIER (Page 1/2) ]
35
A Board Waveforms
20us/div 20us/div 20us/div
TP1
20us/div
TP2
20us/div
TP3
20us/div
TP4
TP5
TP6
1.88 Vp-p (H)
20us/div
1.84 Vp-p (H)
5ms/div
1.86 Vp-p (H)
5ms/div
6.0 Vp-p (H)
20us/div
5.4 Vp-p (H)
TP7 TP8 TP9 TP10 TP11
5ms/div
16.8 Vp-p (H)
1.83 Vp-p (V)
488 mVp-p (V)
49.8 Vp-p (V)
1.06 kVp-p (H)
50.8 Vp-p (V)
A
[ POWER SUPPLY, DEFLECTION, AUDIO AMPLIFIER (Page 2/2) ]
38
39
40