Text preview for : DSC-T1.pdf part of SONY DSC-T1 manual de despiese sony dsc-t1 muy completo
Back to : DSC-T1.pdf | Home
DSC-T1
SERVICE MANUAL
Ver 1.5 2005. 06
Revision History How to use Acrobat Reader LEVEL
2
DSC-T1
US Model Canadian Model AEP Model UK Model E Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model
Link
SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST
· For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987628053.pdf). · For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987628043.pdf). · Reference No. search on printed wiring boards is available. On the LD-140, MS-148 and SY-95 boards
This service manual provides the information that is premised the circuit board replacement service and not intended repair inside the LD-140, MS-148 and SY-95 boards. Therefore, schematic diagram, printed wiring board, waveforms, mounted parts location and electrical parts list of the LD-140, MS-148 and SY-95 boards are not shown. The following pages are not shown. Schematic diagram ............................. Pages 4-15 to 4-36 Mounted parts location ............................. Pages 4-54 to 4-55 Printed wiring board ............................ Pages 4-45 to 4-52 Electrical parts list ................................... Pages 5-7 to 5-11
DIGITAL STILL CAMERA
DSC-T1
SPECIFICATIONS
x Camera [System]
Image device 7.66 mm (1/2.4 type) color CCD Primary color filter Total pixels number of camera Approx. 5 255 000 pixels Effective pixels number of camera Approx. 5 090 000 pixels Lens Carl Zeiss Vario-Tessar 3× zoom lens f = 6.7 20.1 mm (38 114 mm when converted to a 35 mm still camera) F3.5 4.4 Exposure control Automatic exposure, Scene selection (8 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash File format (DCF compliant) Still images: Exif Ver. 2.2 JPEG compliant, DPOF compatible Audio with still image: MPEG1 compliant (Monaural) Movies: MPEG1 compliant (Monaural) Recording media "Memory Stick Duo" Flash Recommended distance (ISO set to Auto): 0.3 m to 1.5 m (11 7/8 inches to 59 1/8 inches) (W) 0.5 m to 1.5 m (19 3/4 inches to 59 1/8 inches) (T)
[General]
Used battery pack NP-FT1 Power requirements 3.6 V Power consumption (during shooting) 1.6 W Operating temperature 0°C to +40°C (+32°F to +104°F) Storage temperature 20°C to +60°C (4°F to +140°F) Dimensions 91 × 60 × 21 mm (3 5/8 × 2 3/8 × 2 7/32 inches) (W/H/D, excluding maximum protrusions) Mass Approx. 180 g (6.3 oz) (including battery pack NP-FT1, "Memory Stick Duo" and wrist strap) Built-in microphone Electret condenser microphone Built-in speaker Piezo-electric speaker Exif Print Compatible PRINT Image Matching II Compatible
x AC-LM5 AC Adaptor
Power requirements 100 to 240 V AC, 50/60 Hz Current consumption 0.2 A Power consumption 10 W Rated output voltage 4.2 V DC, 1.5 A Operating temperature 0°C to +40°C (+32°F to +104°F) Storage temperature 20°C to +60°C (4°F to +140°F) Dimensions Approx. 47 × 30 × 80mm (1 7/ 8 × 1 3/16 × 31/4 inches) (W/H/D, excluding projecting parts) Mass Approx. 170 g (6.0 oz) excluding power cord (mains lead)
x NP-FT1 battery pack
Used battery Lithium-ion battery Maximum voltage DC 4.2 V Nominal voltage DC 3.6 V Capacity 2.4 Wh (680 mAh)
xUC-TA USB cradle [Input and Output connectors]
A/V OUT (MONO) jack (Monaural) Minijack Video: 1 Vp-p, 75 , unbalanced, sync negative Audio: 327 mV (at a 47 k load) Output impedance 1 k USB jack B USB connection High-Speed USB (USB 2.0 High-Speed compatible) DC IN jack Camera connector
x Accessories
· · · · · · · · · · · AC-LM5 AC Adaptor (1) Power cord (mains lead) (1) UC-TA USB cradle (1) USB cable (1) NP-FT1 battery pack (1) A/V connecting cable (1) Wrist strap (1) "Memory Stick Duo" (32 MB) (1) Memory Stick Duo Adaptor (1) CD-ROM (USB driver SPVD-013) (1) Operating instructions (1)
[Input and Output connectors]
Multi connector
[LCD screen]
LCD panel 6.2 cm (2.5 type) TFT drive Total number of dots 211200 (960×220) dots
Design and specifications are subject to change without notice.
--2--
DSC-T1
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
2. 3.
4.
5. 6.
: LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
--3--
DSC-T1
TABLE OF CONTENTS SERVICE NOTE ........................................................ 1-1 5. REPAIR PARTS LIST DISASSEMBLY
5-1. EXPLODED VIEWS ······················································ 5-1 5-1-1. OVERALL SECTION ···················································· 5-3 5-1-2. BATTERY HOLDER SECTION ···································· 5-4 5-1-3. CABINET (REAR) SECTION ······································· 5-5 5-2. ELECTRICAL PARTS LIST ·········································· 5-6 Parts list of the SY-95, MS-148 and LD-140 boards are not shown. Pages from 5-7 to 5-11 are not shown.
1. 2.
2-1. DISASSEMBLY ······························································ 2-1 2-2. SERVICE POSITION ····················································· 2-3 2-3. CIRCUIT BOARDS LOCATION ··································· 2-5 2-4. FLEXIBLE BOARDS LOCATION ································ 2-5 HELP (List of caution points is shown here.)
3.
3-1. 3-2. 3-3. 3-4.
BLOCK DIAGRAMS
OVERALL BLOCK DIAGRAM (1/2) ··························· 3-1 OVERALL BLOCK DIAGRAM (2/2) ··························· 3-3 POWER BLOCK DIAGRAM (1/2) ································ 3-5 POWER BLOCK DIAGRAM (2/2) ································ 3-7
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/2) ······················· 4-1 FRAME SCHEMATIC DIAGRAM (2/2) ······················· 4-3 4-2. SCHEMATIC DIAGRAMS · CD-463 (CCD IMAGER) SCHEMATIC DIAGRAM ······························ 4-7 · CN-198 (MULTI CONNECTOR) SCHEMATIC DIAGRAM ······························ 4-9 · ST-86 (FLASH) SCHEMATIC DIAGRAM ···························· 4-11 · CONTROL SWITCH BLOCK (PW-125) SCHEMATIC DIAGRAM ···························· 4-13 Shematic diagram of the SY-95, MS-148 and LD-140 boards are not shown. Pages from 4-15 to 4-36 are not shown. 4-3. PRINTED WIRING BOARDS · CD-463 (CCD IMAGER) PRINTED WIRING BOARD ······················· 4-41 · ST-86 (FLASH) PRINTED WIRING BOARD ······················· 4-42 · CN-198 (MULTI CONNECTOR) PRINTED WIRING BOARD ······················· 4-43 Printed wiring board of the SY-95, MS-148, LD-140 and FP-694 boards are not shown. Pages from 4-45 to 4-52 are not shown. 4-4. MOUNTED PARTS LOCATION ································· 4-53 Mounted parts location of the SY-95, MS-148 and FP-695 boards are not shown. Pages from 4-54 to 4-55 are not shown.
--4--
DSC-T1 SECTION 1 SERVICE NOTE
· NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When remove a connector, don't pull at wire of connector. Be in danger of the snapping of a wire.
When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire.
Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside)
[Discharging of the FLASH unit's charging capacitor] The charging capacitor of the FLASH unit is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-T1 is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig. a small clip is attached to each end of a resistor of 1 k /1 W (1-215-869-11) Wrap insulating tape fully around the leads of the resistor to prevent electrical shock.
1 k/1 W
Wrap insulating tape.
Discharging the Capacitor Short circuits between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds.
ST-86 B0ARD
Shorting jig (1k / 1w)
Capacitor
1-1
DSC-T1
[Description on Self-diagnosis Display]
Self-diagnosis display · C: ss: ss The contents which can be handled by customer, are displayed. · E: ss: ss The contents which can be handled by engineer, are displayed.
Display Code C:32:01
Countermeasure Turn off the main power then back on. Replace the memory stick. Format the memory stick with the DSC-T1. Checking of flash unit or replacement of flash unit.
Cause Trouble with hardware. · The type of memory stick that cannot be used by this machine, is inserted. · Data is damaged. · Unformatted memory stick is inserted. Abnormality when flash is being charged.
Caution Display During Error SYSTEM ERROR
C:13:01
MS ERROR Flash LED Flash display Flashing at 3.2 Hz
E:91:01 E:01:XX E:61:00 *1 E:61:10 *1
Checking of lens drive circuit
When failed in the focus initialization.
--
Note : The error code is cleared if the battery is removed, except defective flash unit. *1: The error display is given in two ways.
1-2E
DSC-T1 SECTION 2 DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. DISASSEMBLY
Note: The power capacitor of the flash unit is charged up to 315 V maximum. If you touch the capacitor terminal that is charged to high voltage, you will receive an electric shock. This high voltage is not discharged even if you turned off the main power of this set, and it residues. Discharge the residual voltage referring to the service note (page 1-1).
HELP
3 Remove the control switch block in the direction of the arrow. 2
(Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.)
1 2 1 1 1 2 3 1 FP-695 board (21P) 1 1 Five screws (M1.4 ´ 2.5), lock ace, p2 (special) 2 Cabinet (front) assembly 3 Lens shaft 2 2 CCD block assembly (33P) 3 Lens section 1 FP-690 flexible board (19P) 2 ST-86 board, ST terminal cover 1 FP-693 flexible board (16P) 2 Two claws 1
Note: When re-assembling,
confirm the switch position.
1 2
Note: Be careful not to drop
the lens shaft.
3 FP-695 board (Including the LD-140 board)
HELP 01 HELP 08 (disassembly of the Battery holder section)
SY -9
5
5 8 LSV-850A
HELP 02 HELP 03 HELP 06
7 CCD block assembly
4 6
1 Copper leaf protection sheet 2 Flexible board (from LSV-850A)(21P) 3 FP-695 board (Including the LD-140 board) 4 Radiation sheet (CCD) 5 Insulating sheet (CCD) 6 Two tapping screws (B1.2 ´ 3.5)
3 Battery holder section 1 Turn over the control switch block in the direction of the arrow. 2 LCD unit (ACX500EN-J) (25P)
Note: Do not peel off the radiation sheet as
much as possible. If you peel it off, be careful not to damage the flexible board.
1
Note: The CCD imager is not supplied
as a single unit since removing it as a single unit requires adjustment.
2
Mode knob
HELP 05 HELP 07
4 1 7 3 5 6 8
9 Cabinet (rear) assembly
2
5 Microphone 4 6
1 1 Four claws 2 LCD frame 3
1 Harness protection sheet 2 Two claws 3 Microphone holder 4 Two solderings 6 Microphone cushion 7 Control switch block (PW-125)
1
4 Block light guide plate 2
1
HELP 04
2 3 LCD unit (ACX500EN-J) 1 Remove the solderings 2 Four claws
HELP 09
1 Tape (LCD) 2 Four screws (M1.4 ´ 2.5), lock ace, p2 (special) 3 Screw (M1.4 ´ 2.5), lock ace, p2 (special) 4 Slide the mode knob
5 Control switch block, LCD frame 6 LCD unit (ACX500EN-J) Block light guide plate 7 Zoom button 8 SW button
2-1
2-2
DSC-T1
2. DISASSEMBLY
2-2. SERVICE POSITION
2
[SERVICE POSITION TO CHECK THE SY-95 BOARD] Note1: By using an adhesive tape, press the LENS COVER switch (S401). Note2: When checking the VIDEO AMP (SY-95 board IC302) or the USB circuit, connect the cradle.
S401 LENS COVER switch (Note1)
1
(25P) FP-693 flexible board (16P) Control switch block (PW-125)
1 2
Mode knob
9 4
CN402
3 1
5 6
7 8
3
1
2
1
LCD unit (ACX500EN-J), Block light guide plate
CN701 CN703 SY-95 board
S Y9
3
MS-148 board
1 1
5
FP-690 flexible board (19P)
CN704 CN705
CN702 CN-198 board
2
3 2
5
AC IN
AC power adaptor
2
ST-86 board
4
S Y9
FP-695 board (21P)
3
5
1 5 2 1
2 3 1
4
CCD block assembly (33P)
2
Lens section
3
1
Note : The power capacitor of the flash unit is charged up to 315 V maximum. If you touch the capacitor terminal that is charged to high voltage, you will receive an electric shock. This high voltage is not discharged even if you turned off the main power of this set, and it residues. Discharge the residual voltage referring to the service note (page 1-1).
1 2 5
SY -9
3
5
2 3
1
4
2-3
2-4
DSC-T1
2. DISASSEMBLY
2-3. CIRCUIT BOARDS LOCATION
MS-148 SY-95 ST-86
LD-140
CN-198 CD-463 NAME CD-463 CN-198 LD-140 MS-148 ST-86 SY-95 FUNCTION CCD IMAGER MULTI CONNECTOR LENS DRIVE MS I/O, LCD PANEL DRIVE FLASH CAMERA A/D CONVERTER, TIMING GENERATOR, CAMERA DSP, LENS CONTROL, CAMERA SYSTEM CONTROL, HI CONTROL, AUDIO I/O, FLASH DRIVE, DC/DC CONVERTER, CONNECTOR
2-4. FLEXIBLE BOARDS LOCATION
The flexible boards contained in the lens block are not shown.
FP-693 FP-694 CONTROL SWITCH BLOCK (PW-125)
FP-691 FP-690 FP-695
2-5E
DSC-T1
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP 01
HELP 02
LSV-850A Adhesive sheet (LD)
FP-695 flexible board
LD-140 board
FP-695 board
Radiation sheet (CCD)
HELP 03
HELP 04
Tape (LCD)
Insulating sheet (CCD)
HELP 05
HELP 06
Protection sheet (motor)
Harness protection sheet
LSV-850A
Control switch block (PW-125)
Copper leaf protection sheet
HELP
DSC-T1
HELP 07
Microphone holder
HELP 09
Two claws Microphone Sheet (BL) Microphone cushion Two solderings (Black) LCD unit (ACX500EN-J)
(Red)
Control switch block (PW-125)
HELP 10
HELP 11
Light interception sheet (L)
MS-148 board MS protection sheet (S)
SY-95 board
LSV-850A
Sheet
SY -95
MS protection sheet (L) Radiation sheet (D)
Electrostatic sheet (K)
HELP
DSC-T1
HELP 08 (disassembly of the Battery holder section)
5
9 Remove the three solderings
7 Two claws 3 Screw (M1.4 × 2.5), lock ace, p2 (special) 4 Claw 8 SY holder qa Three claws 1 Two claws 2 Cap (multi) 6 Screw (M1.4 × 2.5), lock ace, p2 (special)
qd CN-198 board (6P) qs Battery terminal board
SY -95
q; CN-198 board (19P) qf SY-95 board, MS-148 board qg Remove the two solderings w; Battery holder assembly
S
Y -9
5
qk Three claws
ql CN-198 board qh MS-148 board
wd CN-198 board
S Y -9 5
wa Two solderings
ws Lithium battery
qj SY-95 board
HELP
DSC-T1
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (2/2)
DSC-T1 SECTION 3 BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/2)
LENS UNIT (LSV-850A)
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CD-463 BOARD
IRIS SHUTER
The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment.
SY-95 BOARD(1/2)
CA AD0 134,136,2,4,6 9,12,15,18,21 24,27,30,32 64 55 CA AD13 (AA,AB,Y) (AA,AB,AC,
A18 Y18
IC001
CCD IMAGER 1-5,7-9 11-14 V1A,B V2 V3A,B V4 V5A,B V6 V7A,B V8 15-11,9-7,5-2 CN702 20 21-24 H1A,B H2A,B RG 17
Q004 BUFFER
CCD OUT 30 86
S/H A/D CONV. (1/8)
(J,M,N,P MC D0-D15 R,T,V,M) (21-24)
CLP DM CLP OB
U,V,W,Y)
IC151
21 22 24 25 27 CN702 10,13 113,17 20,109 112,115 125,119 118,121 84 (2/8) (1/8) 126-129 5 CAM SO,SCK EXT CLK CA F CA HD CA F 123,3 XCAM RST 99 CA HD CA F MCK TG AC16
D16
37 42 48 51 33
TIMING GENERATOR
(J,K,L,M, N,P,R,T,U)
(E-H, MC A1-A25 J-M) (21-24)
SYS V MC CKIO
AA8
B16 C15
49,105 66,101,120
T23
A7 H1 C7
FP-691 FLEXIBLE (2/2)
MS SDIO/DATA0-3,MS BS, MS SCLK
MS-148 BOARD(2/3)
4,3,5,7, 2,8 CN101 MEMORY STICK DUO CONNECTOR
A15 D15 B15
TG CLK
AA7
AU LRCK
(3/8)
D16
6 XACCESS LED
X151 54MHz XTAL OSC 1
IC152
FREQUENCY DEVIDER
IC301
CAMERA DSP Y17 AB18
IC501
CAMERA SYSTEM CONTROL
C22
LED DRIVE Q102
SP+ SP-
D103 (ACCESS)
SP901 SPEAKER
LD-140 BOARD
IRIS MOTOR IRIS A IRIS A IRIS B IRIS B G4 H4 G5 H6
FP-695 FLEXIBLE
G1 G2 H2 G3 CN701 18 20 19 HR EN3 HR DIR3A HR DIR3B
HR DIR3A HR DIR3B HR EN0 HR DIR0A HR DIR0B HR EN2 HR DIR2A HR DIR2B XFC RST SENS XZM RST SENS
N21 L21 P21 K20 L22 J21 M21 M20 N20 F21 F20 D13 B13 C13
XMS IN SYS V
M
FOCUS MOTOR
18 21
IC001
IRIS DRIVE
FR SO,SI,SCK XSYS RST XAE LOCK ON XSHTR ON STRB CHG XSTRB FULL XSTRB PWR ON XUSB JACK IN Q504 PRELAMP AF CONT SELF TIMER LED
K2
D14
M
ZOOM MOTOR
8 11
FOCUS A FOCUS A FOCUS B FOCUS B
A6 B5 A4 B4 C1 D2 E1 E2
FOCUS MOTOR DRIVE
C8 C7 B8 B7 B3 A2 B2 A1
15 17 16
HR EN2 HR DIR2A HR DIR2B
AB5 AB13 AD19 AC15 AB11
2
TO OVERALL BLOCK DIAGRAM (2/2)
(PAGE 3-4)
M
FOCUS RESET SENSOR ZOOM RESET SENSOR
12 15
ZOOM A ZOOM A ZOOM B ZOOM B
ZOOM MOTOR DRIVE
12 14 13
HR EN0 HR DIR0A HR DIR0B
L4 F1
H23
5 2 CN002
8 11
XFC RST SENS XIR RST SENS STRB ON PANEL R PANEL G PANEL B HDO PANEL V
AB4
FP-694 FLEXIBLE
8 9 7 LCD901 2.5INCH COLOR LCD PANEL 10 VR VG VB
MS-148 BOARD (1/3)
D6 C7 C6 A7 (2/2) C1 C2 B1
FP-691 FLEXIBLE (1/2)
PANEL R PANEL G PANEL B V OUT
Q302-Q304 BUFFER
CN-198 BOARD(1/2)
XCAM RST CA F EXT CLK AC12
AC9 C23
E23 C23 D23 C18 D17
AC12 A6
AU A IN AU A OUT
J1 K1 L1 M1
CN704 USBPHY D+,D9 8 10 12
(2/8) 2
B11
CN001 MULTI CONNECTOR
Q801,802 PS1G RGT,HCK1,2 REF,HST WIDE,DWN EN,VCK, VST BUFFER
IC803
RGB DRIVE
IC302
VIDEO AMP
4
F23 T20
A11 C11
XSYS RST CAM SO,SCK D1 HDO Q805 LPF PANEL V XSYS RST AU A IN AU A OUT SYS SO,SI,SCK STRB ON BL LEV H4 H5
A12 B12
6 11 12 14 16 21 24
AD14 AB7
MELODY MELODY EW
Q501 MOD BEEP E1 (5/8) B4 4 2 AU OUT V OUT 16 17
G2,F3 E4,F4 F7,E5 A3,B3 C3,A2
TIMING GENERATOR
D2 F5 E3 F2 F1 A4 A5
IC601
AUDIO AMP/ADC A2 D1 B8
SYS SO,SI,SCK
MIC901
1
MIC IN
MIC
ND901 BACK LIGHT
1 3 CN402
LED A LED K
1
TO OVERALL BLOCK DIAGRAM (2/2)
CN001
(PAGE 3-3)
CONTROL SWITCH BLOCK(PW-125) (1/2)
AUDIO SIGNAL VIDEO SIGNAL VIDEO/AUDIO SIGNAL
3-1
3-2
DSC-T1
3. BLOCK DIAGRAMS
3-2. OVERALL BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
MS-148 BOARD (3/3)
S101 MODE SW
FP-691 FLEXIBLE
SY-95 BOARD (2/2)
(4/8)
IC491
HI CONTROL KEY AD0 J6 KEY AD1 H6 KEY AD2 G6
FP-693 FLEXIBLE
12 13 14
CONTROL SWITCH BLOCK(PW-125) (2/2)
S003-011,013 ZOOM,MENU,IMAGE SIZE/DELETE DISPLAY/LCD BACK LIGHT, UP,DOWN,RIGHT, LEFT,SET S001
J8 MODE DIAL
CN-198 BOARD (2/2)
BT001 LITHIUM BATTERY (SECONDARY) 11 VBUS
(
11 CN704 VL 3V
S401 LENS COVER OPEN
)
X402 32.768KHz
B7 XLENZ CAP OPN XPOWER ON B8 J4 32KHz IN XAE LOCK ON J5 32KHz OUT XSHTR ON 7 8 5
POWER S002 SHUTTER D004 (POWER) D003
12 13 14
Q406 USB JACK IN C8 XUSB JACK IN
XPWR LED ON B2
3
CN001 MULTI CONNECTOR
13 14 24
XMULTI JACK IN XAV JACK IN BATT/XEXT
XCHARGE/XSTB LED B1 15 18 17 C4 XMULTI JACK IN A3 XAV JACK IN A7 BATT/XEXT
10
/CHG S012
9
CN001
RESET
3 2 1
ACV UNREG
4 5 6 CN705
Q407 BATT SIG I/F G2 BATT SI G1 BATT SO J1 INIT CHARGE F002 F003 F001 D015 D013 ST UNREG ACV UNREG BATT UNREG FR SO D2 FR SI D1 XFR SCK E1 XSYS RST B3 L8 K8 D8 D011
A10
XAE LOCK ON XSHTR ON XUSB JACK IN
H2 FAST CHARGE E8 SYS DD ON MS IN B6
Q404 XMS IN
FR SO,SI,SCK
2
TO OVERALL BLOCK DIAGRAM (1/2)
(PAGE 3-2)
XSYS RST SYS V STRB CHG XSTRB PWR ON
DDCON SO,SCK
C1 DDCON SO D3 DDCON SCK D7 XRSTX A5 BACK UP VCC H4
SYS V B9
RESET
B7 B9
XRSTX BACK UP VCC
XSTB FULL SELF TIMER LED PRE LAMP AF CONT
B11
3V REG BATTERY IN DETECT
A11
EVER 3.0V BATT IN A9 BATT IN
BT901 BATTERY TERMINAL
C
8
Q002 1 4 5 D036
D9 OUT8A E9 OUT8B D1 BATTERY CHARGER E5 D4 E4 FET DRIVE
A7
FP-690 FLEXIBLE
Q651,652 ST UNREG CN703 1 6
ST-86 BOARD
Q001,002 T002
D2
INIT CHARGE
E3 C7 D7
FAST CHARGE STRB CHG SYS DD ON A 3.1V D 1.2V AU 2.8V D 2.8V A 2.8V CAM 15.0V CAM -8.0V M 5V ST 5V STRB ON STRB ON BL LEV LED A LED K 4 IGBT DRIVE 2 17 (6/8) XSTRB PWR ON XSTRB FULL Q653 (2/2) Q653 (1/2) 15 16
HIGH VOLTAGE CHARGER
XE A(H) C003
(7/8)
IC001
DC/DC CONVERTER
IC651
Q003 FLASH DRIVE XE K(L)
XENON TUBE
1
TO OVERALL BLOCK DIAGRAM (1/2)
(PAGE 3-1)
SELF TIMER LED PRE LAMP AF CONT
Q701 LED DRIVE 19
D003 (AF LED)
(7/8)
IC003
(7/8)
CAM -0.5V
IC007
D 1.8V
3-3
3-4
DSC-T1
3. BLOCK DIAGRAMS
3-3. POWER BLOCK DIAGRAM (1/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-95 BOARD(1/2)
CN-198 BOARD
CN705
BATT UNREG
F001
F002
ST UNREG
ST UNREG
CN001 MULTI CONNECTOR
1 2 3 24
ACV UNREG
4 5 6
F003
ACV UNREG LED A (7/8) LED K BL LV PANEL 13.5V
FB701
BATT/XEXT VL 3V
BT001 LITHIUM BATTERY (SECONDARY)
17 11 CN704
Q002
IC001
DC/DC CONVERTER 8 4 5 D4 E5 INIT CHARGE BATTERY CHARGER 1 D1 VCC1A G11 VCC1B G10 VCC1C G9 OUT11A H11 OUT11B H10 OUT11C J11 FET DRIVE OUT12A L11 OUT12B K10 OUT12C J9 VCH1A L10 VCH1B K9 VCH1C(FB4) L9 VCC2 F9 L005
A11
BATT UNREG
BT901 BATTERY TERMINAL
C
BATT SIG
L006
L003 L010 D026 (RECT)
AV 2.8V A 2.8V D 2.8V
D2 E4
FAST CHARGE D013 L002
E3 E9 OUT8A D9 OUT8B 3V REG
(7/8) 2
BATT UNREG
IC007
1.8V REG
3
D 1.8V
ACV UNREG EVER 3.0V
D015
L001
B11
OUT2 F10 VCH2 E11 OUT3A J3 OUT3B K1 OUT3C J2 BATTERY IN DETECT RESET VCH3A(FB3) J1 VCH3B H4 VCH3C(FB6) H3 VCH3S H2 VCC GD H1 OUT4 K6 D023 (RECT) VCH4 J6 VCC5 K5
D 1.2V
D011
A10
1
TO POWER BLOCK DIAGRAM (2/2)
L007
(PAGE 3-7)
M 5V
D8
H8 BATT SENS
BACK UP VCC
A5 H4
D017 (RECT)
B9 B7 A7
CONTROL SWITCH BLOCK (PW-125)
FP-693 FLEXIBLE
Q407 I/F
XRST X D7 G8 ACV SENS BATT IN A9
ST 5V
A7 BATT/XEXT G2 BATT SI G1 BATT SO B8 XPWR ON
DDCON SO C1 DDCON SCK D3 XCS DD CON H1 SYS DD ON E8
DDCON SO,SCK,XCS
L8 DIN K8 CLK K7 LD C7 SYS DD ON D7
L008 CAM 15.0V
S001 POWER 5 4 3 D004 (POWER) 11 10 D003 /CHG
INIT CHARGE J1 B2 XPOWER LED ON FAST CHARGE H2
OUT5 L5 L009 VCH5 J5 OUT6 F1 VCH6 G1 ICH6 G2 REF6 B1 CBG B5 VLD04 C8 VLD05 B8 D025 (RECT) LED K BL LV (7/8) D021 (RECT) L004 LED A 3 2 8 VCC+ 4 VCC1 SHUNT REG Q001
CAM -8.0V
CAM -0.5V
B1 XCHARGE/XSTRB LED
DDCON SENS F8
(4/8)
S012 RESET CN001 9
IC491
HI CONTROL
IC003
-0.5V REG PANEL 13.5V A 3.1V
D 1.2V
3-5
3-6
DSC-T1
3. BLOCK DIAGRAMS
3-4. POWER BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SY-95 BOARD(2/2)
D 2.8V MS PWR ON ST UNREG LED A LED K D 2.8V BL LV PANEL 13.5V AV 2.8V AV 2.8V (5/8) BL LEV PANEL 13.5V
FP-691 FLEXIBLE
MS-148 BOARD
Q101 CN101 VCC 9 MEMORY STICK DUO CONNECTOR LCD901 2.5INCH COLOR LCD UNIT (ACX500EN-J)
20
IC803 IC601
ST 5V AUDIO AMP/ADC LED A LED K A5 A4 RGB DRIVE TIMING GENERATOR ND901 BACK LIGHT
1 CN402 3
(3/8) A 2.8V D 2.8V D 1.8V D 1.2V A 3.1V
AD18 AD51 AB11 AC15 AC20 F22
MS PWR ON CN703 STRB CHG XSTRB PWR ON XSTRB FULL CAM DD ON XSTRB PWR ON AMP OUT ON Q653 15 STRB CHG HIGH VOLTAGE CHARGER ST UNREG Q651,652 1 6 Q001,002,T002
IC501
CAMERA SYSTEM CONTROL
FP-694 FLEXIBLE
XE A(H) C003
XENON TUBE
A 2.8V Q302-304 (2/8) PANEL R,G,B BUFFER MT 5V 18 XSTRB FULL 16
1
TO POWER BLOCK DIAGRAM (1/2)
IC302
VIDEO AMP
Q305,306
D003 AF LED
(PAGE 3-6)
Q655,656
FP-690 FLEXIBLE
ST-86 BOARD
AU 2.8V A 2.8V D 2.8V D 1.2V
(2/8)
IC301
CAMERA DSP
J22 V21
(6/8) XFC RST LED XZM RST LED
IC651
IGBT DRIVE CN701 M 5V 1 2 3
M 5V ST 5V D 2.8V
IC001
IRIS/FOCUS/ ZOOM DRIVE
D 2.8V
LENS UNIT (LSV-850A)
X151 (1/8)
IC152
FREQUECY DEVIDER CAM DD ON Q151,152 CAM 15V CAM -8.0V
54MHz XTAL OSC
Q702 7 XFC RST LED F RST VCC 6 FOCUS RESET SENSOR
Q702 10 33 17 CN702 Z RST VCC CN002 3
ZOOM RESET SENSOR
IC001
CCD IMAGER
XZM RST LED
FP-695 FLEXIBLE
LD-140 BOARD
(1/8) A 2.8V CAM -0.5V A 3.1V
IC151
S/H,A/D CONV. TIMING GENERATOR
CD-463 BOARD
The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment.
3-7
3-8E
DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM (1/2)
1 2 3 4 5 6 7 8
TO SY-95 BOARD(2/2)
9
10
11
12
13
14
15
16
17
18
A
FRAME SCHEMATIC DIAGRAM(1/2)
SY-95 BOARD(1/2) B
CN702 33P 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 ND901 BACK LIGHT CN402 1 25P REG_GND V8 V7B V7A V6 VHLD
C
V5B V5A V4 VST V3B V3A V2 V1B
LED_A N.C. LED_K BL_THH BL_THL RGT VB VR VG PSIG HCK1 HCK2 CREXT REF HST WIDE REG_GND VDDG VSS VDD DWN EN VCK VST COM LCD901 2.5INCH COLOR LCD UNIT (ACX500EN-J)
FP-694
FLEXIBLE
2 3 4 5 6 7 8 9 10 11
D CD-463 BOARD
V1A REG_GND CAM_-8.0V_CD VSUB_CONT SHT REG_GND H1A H1B
E
REG_GND H2A H2B REG_GND RG REG_GND REG_GND CCD-OUT
MS-148 BOARD
12 13 14 15 16 17 18 19 20 21 22 23 24 25
F
REG_GND POWER_SAVE CAM_15V_CD
CN704
19P 1 2 3 4 1 GND BS DATA1 SDIO/DATA0 DATA2 INT DATA3 SCLK VCC GND MEMORY STICK DUO CONNECTOR 5 2 6 3 7 4 8 5 9 6 10 11 12 13 14 15 16 17 18 19 7 8 9 10 CN101 10P
REG_GND(AU)
G
27
CN001 1 3 5 7 26P
V_OUT REG_GND(AU) AU_OUT
29
REG_GND(AU) ACV_UNREG LANC_DC LANC_SIG USB/LANC_GND D+ DXAV_JACK_IN A_OUT_L A_OUT_R A_GND AUX BATT/XEXT ACV_GND 2 4 6 8 10 12 14 16 18 20 22 24 26 BT001 LITHIUN BATTERY (SECONDARY) REG_GND(USB) REG_GND(USB) USBPHY_DUSBPHY_D+ REG_GND(USB)
ACV_UNREG ACV_UNREG XLANC_JACK_IN USB_LED USB_HOST USB_VBUS XMULTI_IN EXT_STRB_ON V_OUT V_GND AUX ACV_GND ACV_GND
H
9 11 13 15 17 19 21 23
CN-198 BOARD
VL_3V VBUS VBUS VBUS XMULTI_IN NC BATT/XEXT XAV_JACK_IN NC
FP-691
FLEXIBLE
I
25
MULTI CONNECTOR CN705 6P 1 2 3 4 5 6 ACV_GND ACV_GND ACV_GND
28
30
J
16
ACV_UNREG0 ACV_UNREG0 ACV_UNREG0
4-1
4-2
FRAME SCHEMATIC DIAGRAM (1/2)
DSC-T1
4-2. SCHEMATIC DIAGRAMS
FRAME SCHEMATIC DIAGRAM (2/2)
1 2 3 4 5 6 7 8 9 10 11
4-3. PRINTED WIRING BOARDS
A
FRAME SCHEMATIC DIAGRAM(2/2)
CN001 16P 10 11 12 13 14 15 REG_GND XCHARGE/XSTRB_LED XPOWER_LED_ON XAE_LOCK_ON XPOWER_ON XRESET_SW EVER_3.0V XSHTR_ON EVER_3.0V REG_GND REG_GND KEY_AD0 KEY_AD1 KEY_AD2 MIC_IN NC 16 1 2 3 4 5 6 7 8 9
CONTROL SWITCH BLOCK (PW-125)
B
FP-693 C
CN703 19P 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 STB_UNREG STB_UNREG STB_UNREG
FLEXIBLE
ST-86 BOARD D
FP-690
FLEXIBLE
STB_UNREG STB_UNREG STB_UNREG REG_GND REG_GND REG_GND REG_GND REG_GND REG_GND
E
REG_GND REG_GND XSTRB_PWR_SAVE STB_FULL IGBT_ON AF_LED_5V AF_LED_K
F
LENS UNIT (LSV-850A)
CN002 21P 1 2 M_5V Z_RST_VCC F_RST_GND 3 D_2.8V 4 REG_GND F_RST_SENS F_RST_VCC N.C FOCUS_A FOCUS_B FOCUS_A FOCUS_B ZOOM_A 5 REG_GND 6 REG_GND 7 F_RST_VCC 8 XFC_RST_SENS 9 10 11 12 HR_EN0 ZOOM_A ZOOM_B ZOOM_B TEMP_OUT TEMP_GND IRIS_A IRIS_A IRIS_B 13 HR_DIR0B 14 HR_DIR0A 15 HR_EN2 16 HR_DIR2B 17 HR_DIR2A 18 HR_EN3 19 HR_DIR3B 20 HI_DIR3A IRIS_B 21 XCAM_DR_PS 21 20 19 18 17 16 15 14 13 12 8 9 10 11 7 6 5 4 3 2 CN701 21P 1 M_5V Z_RST_SENS Z_RST_GND
SY-95 BOARD(2/2)
G
FP-695
FLEXIBLE
LENS_TEMP Z_RST_VCC XZM_RST_SENS
H
I
LD-140 BOARD
J
16
TO SY-95 BOARD(1/2)
FRAME SCHEMATIC DIAGRAM (2/2)
4-3
4-4
DSC-T1
4-2. SCHEMATIC DIAGRAMS
Link
CD-463 BOARD (CCD IMAGER) CN-198 BOARD (MULTI CONNECTOR) ST-86 BOARD (FLASH) CONTROL SWITCH BLOCK (PW-125)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
DSC-T1
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For schematic diagrams) · All capacitors are in µF unless otherwise noted. pF : µ Link V or less are not indicated except for electrolytics µF. 50 and tantalums. · Chip resistors are 1/10 W unless otherwise noted. k=1000 , M=1000 k. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Kinds of capacitor Temperature characteristics External dimensions (mm) · Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · Parts with * differ according to the model/destination. Refer to the mount table for each function. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2: non flammable resistor · 5: fusible resistor · C: panel designation · A: B+ Line · B: B Line · J : IN/OUT direction of (+,) B LINE. · C: adjustment for repair. · A: VIDEO SIGNAL (ANALOG) · A: AUDIO SIGNAL (ANALOG) · A: VIDEO/AUDIO SIGNAL (ANALOG) · A: VIDEO/AUDIO/SERVO SIGNAL · A: SERVO SIGNAL · Circled numbers refer to waveforms. (Measuring conditions voltage and waveform) · Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used) · Voltage values change depending upon input impedance of VOM used.)
Front of the lens
1. Connection
Pattern box
About 30cm
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H
Cyan Green
White Magenta
A B
A=B
Fig. a (Video output terminal output waveform)
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please include the board name.
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Precautions Upon Replacing CCD imager
· The CD-463 board mounted as a repair part is not equipped with a CCD imager. When replacing this board, remove the CCD imager from the old one and mount it onto the new one. · If the CCD imager has been replaced, carry out all the adjustments for the camera section. · As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light.
4-5
Red Blue
B A
DSC-T1
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
For Schematic Diagram · Refer to page 4-41 for printed wiring board.
CD-463 PRINTED WIRING BOARD
1 CD-463 BOARD A
CCD IMAGER
XX MARK:NO MOUNT NO MARK:REC/PB MODE
2
3
4
5
6
7
8
9
B
14 13 12 11 10
9
V5B
8
V5A
7
V4
6
Vst
5
V3B
4
V3A
3
V2
2
V1B
1
V1A VL
C
REC PB
VIDEO SIGNAL CHROMA Y Y/CHROMA
IC001
CCD IMAGER
The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment.
CCD-OUT
15 16 17 18 19 20 21 22 23 24 25 26 27 28
D
14.9 Q004 2SC4250(T5LSONY1) BUFFER C002 0.1u 16V B
CAM_15V_CD POWER_SAVE
R002 22k 10.6 R003 3900 1005
R001 1500 C004 5p CH 0 Q001 DTC144EUA-T106 SWITCH 3.5 R005 1200
E
REG_GND CCD_OUT REG_GND REG_GND RG REG_GND H2B H2A R006 0 Q002 0 DTC144EUA-T106 SWITCH
C001 0.1u 16V B 0
CSUB
Rss3
GND
GND
GND
SUB
H2B
H2A
H1B
H1A
RG
VH
IC001
ICX473CQZ-13
SIGNAL PATH
Vhld
V7B
V7A
V8
V6
R004 1800
12 C005 0.1u 16V B
F
TO SY-95 BOARD (1/8) CN702
REG_GND H1B H1A REG_GND SHT VSUB_CONT CAM_-8.0V_CD REG_GND C003 0.1u 16V B Q003 DTC144EHT2L SWITCH
(PAGE 4-15 of LEVEL3)
G
V1A V1B V2 V3A V3B VST V4 V5A
H
16
V5B VHLD V6 V7A V7B V8 REG_GND
4-7
4-8
CD-463
DSC-T1
4-2. SCHEMATIC DIAGRAMS
For Schematic Diagram · Refer to page 4-43 for printed wiring board.
CN-198 PRINTED WIRING BOARD
1
2
3
4
5
6
7
8
9
10
11
12
CN-198 BOARD
MULTI CONNECTOR
A
XX MARK:NO MOUNT
NC XAV_JACK_IN BATT/XEXT NC XMULTI_IN VBUS C001 100p CH FB002 0uH FB001 0uH
B
VBUS TO SY-95 BOARD (8/8) CN704 VBUS VL_3V
(PAGE 4-30 of LEVEL3)
1
2
REG_GND(USB) USBPHY_D+ USBPHY_D-
3 4
2 1
3 4
2 LND026 1 STATIC_GND
R004 0
CN001 MULTI CONNECTOR
4
3
D002 DF3A8.2C(TPL3)
REG_GND(USB) REG_GND(USB)
D001 MA4L11100AS0
D003 DF3A8.2C(TPL3) 26P
3
AU_OUT REG_GND(AU) V_OUT REG_GND(AU) R002 100k
ACV_UNREG XLANC_JACK_IN USB_LED USB_HOST USB_VBUS XMULTI_IN EXT_STRB_ON V_OUT V_GND AUX ACV_GND ACV_GND
LANC_DC LANC_SIG USB/LANC_GND D+ DXAV_JACK_IN A_OUT_L A_OUT_R A_GND AUX BATT/XEXT ACV_GND
4 D004 DF3A8.2C(TPL3)
1
5
7
D
R001 47k R003 0 LF001 1 2 3 4
D005 DF3A8.2C(TPL3)
FB003 0uH
E
D008 XX
D009 DF3A8.2C (TPL3)
25 23 21 19 17 15 13 11
R005 XX
F
ACV_GND TO SY-95 BOARD (8/8) CN705 ACV_GND ACV_GND ACV_UNREG0
(PAGE 4-30 of LEVEL3)
ACV_UNREG0 ACV_UNREG0 BT001 LITHIUM BATTERY (SECONDARY)
G
16
SIGNAL PATH
VIDEO SIGNAL CHROMA REC PB Y Y/CHROMA AUDIO SIGNAL
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
CN-198
4-9
4-10
26 24 22 20 18 16 14 12 10
2
3
4
1
9
8
6
4
C
1
REG_GND(AU) 3 2
ACV_UNREG
ACV_UNREG
2
DSC-T1
4-2. SCHEMATIC DIAGRAMS
For Schematic Diagram · Refer to page 4-42 for printed wiring board.
ST-86 PRINTED WIRING BOARD
1 ST-86 BOARD A
FLASH
XX MARK:NO MOUNT NO MARK:REC/PB MODE
2
3
4
5
6
7
8
9
T002 CONVERTER TRANSFORMER CL001 STB_UNREG REG_GND 4 P S 5
D002 HAU160C030STP
LND001 C002 0.01u B 1 F 3 R001 4700 Q001 CPH3205-SONY-TL-E 0 Q001,002 HIGH VOLTAGE CHARGER 0 R005 180 XE_A(H)
TO FP-690 FLEXIBLE
XSTRB_PWR_ON STB_FULL IGBT_ON AF_LED_5V AF_LED_K
B
(PAGE 4-26 of LEVEL3)
+
R008 1M
2
XENON TUBE
LND003 TRIGGER_IN LND004
R003 120
TRIGGER GND C003 63u 315V
XE_K(L)
Q002 MCH3405-TL-E 0 2.7 R002 100k 0
C
LND002 268 8
Q003 CY25AAJ-8-T13 FLASH DRIVE C004 47000pF 7 6 2 5 1
R004 10k R006 47
4
D
CL002 D001 MA111-(K8).S0
0 R007 1M
CL003
CL004
CL005
E
CL006 D003 S4G49(SONY) (AF LED)
CL007
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
F
16
3
4-11
4-12
ST-86
DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
1
2
3
4
5
6
7
8
9
CONTROL SWITCH BLOCK(PW-125) A
CN001 MIC_IN REG_GND XPOWER_LED_ON EVER_3.0V XPOWER_ON TO SY-95 BOARD (8/8) REG_GND XAE_LOCK_ON XHTR_SW XRESET_SW XCHARGE/XSTRB_LED EVER_3.0V KEY_AD0 KEY_AD1 KEY_AD2 REG_GND 16P 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 S002 (Shutter) R007 1500 S006 S010 S001 POWER D004 (POWER) R001 470 MIC901
(MIC)
SIGNAL PATH
AUDIO SIGNAL
B
THROUGH THE FP-693 FLEXIBLE
(PAGE 4-29 of LEVEL3)
C
NC
R006 3300
S012 RESET
S008
D
D003 /CHG
S005
S011
R009 3300
R002 240 R005 1500 R008 1200 R004 1200 R003 1200 S009 S013 (Display/LCD back light on/off)
E
S003 W (ZOOM)
S004 T
(Image Size /DELETE)
S007
F
16
MENU
Schematic diagram of the LD-140, MS-148 and SY-95 boards are not shown. Pages from 4-15 to 4-36 are not shown.
CONTROL SWITCH BLOCK 4-13 4-14
DSC-T1
4-3. PRINTED WIRING BOARDS
Link
CD-463 BOARD ST-86 BOARD CN-198 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION FLEXIBLE BOARDS LOCATION
NAME CD-463 CN-198 LD-140 MS-148 ST-86 SY-95
FUNCTION CCD IMAGER MULTI CONNECTOR LENS DRIVE MS I/O, LCD PANEL DRIVE FLASH CAMERA A/D CONVERTER, TIMING GENERATOR, CAMERA DSP, LENS CONTROL, CAMERA SYSTEM CONTROL, HI CONTROL, AUDIO I/O, FLASH DRIVE, DC/DC CONVERTER, CONNECTOR
DSC-T1
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block)
(For printed wiring boards) · : Uses unleaded solder. · : Pattern from the side which enables seeing. (The other layers' patterns are not indicated) · Through hole is omitted. · Circled numbers refer to waveforms. · There are a few cases that the part printed on diagram isn't mounted in this model. · C: panel designation
· Chip parts. Transistor
C 6 5 4 4 5 6 5 4 4 5
Diode
3 3 3 1 23
B
E
1 2 3 3 2 1 1 2 3 3 2 1 1 2 2 1 3 4
2 1
1 2 2 3
1 2 4 4
1 6 54 3 3 4
5 4 3 3 4 5 2
1
4 5
3 2 4
6
1 1 2 4 3
2
1
1
3 1
3
1
2
BOARD INFORMATION board name CD-463 ST-86 CN-198 FP-694 LD-140 FP-695 MS-148 SY-95 parts location 4-53 4-53 4-53 4-54 4-55 4-54 2 4 4 2 4 1 6 8 pattern 2 and 3 2 and 3 2 to 5 2 to 7 CSP IC IC001 IC803 IC001, IC151, IC301, IC491, IC501, IC601 (shown on page) number of layers layers not shown
4-39
DSC-T1
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
· Refer to page 4-39 for common note for printed wiring board.
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
·
: Uses unleaded solder.
CD-463 BOARD
R005
A
R001
ST-86 BOARD(SIDE A)
ST-86 BOARD(SIDE B)
LND002 CL001 LND001 CL006 CL005 CL007 CL002 CL003 CL004
4
A
Q003
A
IC001
Q004
R003
28
25
20
15
Q001
B C E
C004
C002
2
R004
C005
C001
1
5
10
14
C003
R006
R002
T002
Q002
3
B
B
A
D003
K
LND004
LND003
B
1
5
C
R001
D002
C
Q001
R008
C
LND002 LND004 LND006 LND008 LND010 LND012 LND014 LND016 LND018 LND020 LND022 LND024 LND026 LND028 LND030 LND032 LND001 LND003 LND005 LND007 LND009 LND011 LND013 LND015 LND017 LND019 LND021 LND023 LND025 LND027 LND029 LND031 LND033
1-860-520-
11 12
R004
D001
R003 R005
C004 C003
C002
8
5
D
G
R002
Q003
D
4
Q002
D
S
D
1
R007 R006
16
1
The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment.
2
3
4
5
1-860-525-
11
1-860-52511
E
E
16
1
2
3
3
2
1
16
4-41
4-42
CD-463/ST-86
DSC-T1
4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
· Refer to page 4-39 for common note for printed wiring board.
·
: Uses unleaded solder.
CN-198 BOARD(SIDE A)
A
D001
R005
1 4 2 3
1 4
D005
2 3
C001
2 1
R004 R002 R001 R003 3
D004
1 4
2 3
D002 D008
B
FB001 FB003 FB002
3 4 1 2
D009
2 1
1-860-527-
21
LF001
D003
3 2
4 1
3 2
2
4 1
C
1
16
BT001 LITHIUM BATTERY (SECONDARY)
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
1
2
3
4
5
6
CN-198 BOARD(SIDE B)
A
1 5 2 10
15
25 20 26
CN001
1-860-52721
B
MULTI CONNECTOR
C
Printed wiring board of the FP-695, MS-148, SY-95 and FP-694 boards are not shown. Pages from 4-45 to 4-52 are not shown.
6
CN-198
5
4-43
4
3
2
1
16
4-44
DSC-T1
4-3. PRINTED WIRING BOARDS
4-4. MOUNTED PARTS LOCATION
CD-463 BOARD
C001 C002 C003 C004 C005 IC001 Q001 Q002 Q003 Q004 R001 R002 R003 R004 R005 R006 A-4 A-5 A-4 A-4 A-4 A-3 A-4 A-5 A-4 A-5 A-4 B-5 A-4 A-4 A-4 A-4
no mark : side A * mark : side B CN-198 BOARD
BT001 C001 C-2 B-3
ST-86 BOARD
C002 C003 * C004 D001 * D002 D003 Q001 Q002 * Q003 R001 R002 R003 R004 R005 * R006 * R007 * R008 * T002 D-1 D-2 C-1 C-1 C-1 B-3 C-1 D-1 D-1 C-1 D-1 D-1 D-1 D-1 D-1 D-1 C-1 B-2
* CN001 B-3 D001 D002 D003 D004 D005 D008 D009 FB001 FB002 FB003 LF001 R001 R002 R003 R004 B-3 B-3 B-3 B-3 B-3 B-3 B-4 B-3 B-3 B-3 B-3 B-4 B-4 B-3 B-3
Mounted parts location of the LD-140, MS-148, and SY-95 boards are not shown. Pages from 4-54 to 4-55 are not shown.
4-53E
CD-463/ST-86/CN-198
DSC-T1
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
EXPLODED VIEWS
SY -9
5
A
B
OVERALL SECTION
BATTERY HOLDER SECTION
CABINET (REAR) SECTION
Link
CD-463 BOARD CN-198 BOARD
ELECTRICAL PARTS LIST
ST-86 BOARD
B A A
ACCESSORIES
B B
MS-148 BOARD SY-95 BOARD
LD-140 BOARD
DSC-T1
5. REPAIR PARTS LIST
NOTE: · -XX, -X mean standardized parts, so they may have some differences from the original one. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · CAPACITORS: uF: µF · COILS uH: µH · RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable · SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD...
When indicating parts by reference number, please include the board name. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
5-1
DSC-T1
Ver 1.5 2005. 06
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. OVERALL SECTION
ns : not supplied
7
Cabinet (rear) section (See page 5-5)
SY -9
5
B A
2
Battery holder section (See page 5-4)
6
5 4 ns 1 3
7
LD-140 board (Note 1)
B
17
9
15 14
A
18
16
13 12 7
Note 1: LD-140 board is included in the FP-695 complete board . LD-140 board is not supplied as an independent service parts. Note 2: CD-463 board is included in the CCD block assy. CD-463 board is not supplied as an independent service parts. Note 3: The CCD imager is included in the CCD block assy . The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment.
10
CD-463 board (Note 2)
8
CCD imager (Note 3)
11
Be sure to read "Precautions upon replacing CCD imager" on page 4-5 when changing the CCD imager.
Ref. No. 1 2 3 04 5 6 7 8 9 Part No. X-3953-789-1 3-087-670-01 A-7078-867-A 1-478-385-11 1-860-515-11 3-086-275-01 3-086-218-01 3-086-236-01 A-7113-001-A Description CABINET (FRONT) ASSY GASKET (K) ST-86 BOARD, COMPLETE LUMINOUS UNIT, STROBOSCOPE FP-690 FLEXIBLE BOARD COVER, ST TERMINAL SCREW (M1.4), LOCK ASE, SPECIAL SHEET (CCD), RADIATION LENS ASSY (SERVICE EXCLUSIVE) Ref. No. 10 11 12 13 14 15 16 17 18 Part No. A-7111-623-A 3-086-156-11 3-086-238-01 3-086-276-01 3-086-237-01 A-7078-877-A 3-088-401-01 3-089-986-01 3-089-781-01 Description CCD BLOCK ASSY (Supplied with CD-463 board) SCREW B1.2 SHEET (CCD), INSULATING SHAFT, LENS SHEET (LD), ADHESIVE FP-695 BOARD, COMPLETE SHEET, PROTECTION, COPPER LEAF SHEET (L), LIGHT INTERCEPTION SHEET (MOTOR), PROTECTION
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
5-3
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
DSC-T1
Ver 1.5 2005. 06
5. REPAIR PARTS LIST
5-1-2. BATTERY HOLDER SECTION
ns : not supplied
60 61
SP901
63 59 51 58
ns
MS
-14
64
8
53 54 65
ns SY-95 board (Note)
52
BT901
57
SY -95
55 56
ns BT001
67
64 66
72
69
68
Note : SY-95 board is included in the SY-MS complete board . SY-95 board is not supplied as a single board since removing it as a single board requires adjustment.
71
: BT001 (Lithium battery) CN-198 board on the mount position. (See page 4-43)
Ref. No. 51 52 53 54 55 56 57 58 59 60 61
Part No. A-7079-000-A 1-860-517-11 1-860-516-11 X-3953-783-1 3-086-216-01 3-086-210-02 3-355-424-01 A-7078-865-A 1-860-518-11 3-086-222-01
Description SY-MS BOARD, COMPLETE (SERVICE) FP-693 FLEXIBLE BOARD FP-691 FLEXIBLE BOARD HOLDER ASSY, BATTERY FOOT, RUBBER LID, BT SCREW, TAPPING MS-148 BOARD, COMPLETE FP-694 FLEXIBLE BOARD SHEET (S), PROTECTION, MS
Ref. No. 63 64 65 66 67 68 69 71 72 0 BT001 BT901 SP901
Part No. 3-086-221-01 3-086-218-01 3-086-223-01 3-086-219-01 A-7078-870-A 3-086-217-01 3-089-013-02 3-089-985-01 3-086-220-01 1-528-999-51
Description SHEET (SPEAKER), ADHESIVE SCREW (M1.4), LOCK ASE, SPECIAL SHEET (L), PROTECTION, MS HOLDER, SY CN-198 BOARD, COMPLETE CAP (MULTI) SHEET (K), ELECTROTATIC SHEET SHEET (SY), SLIDE BATTERY, LITHIUM SECONDARY
3-086-752-01 CUSHION (RING)
1-780-061-11 TERMINAL BOARD, BATTERY 1-825-644-11 BUZZER, PIEZOELECTRIC
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
5-4
DSC-T1
5. REPAIR PARTS LIST
5-1-3. CABINET (REAR) SECTION
ns : not supplied
110 108 107 115 106
114 111
MIC901
ns
105 104
LCD901
109
112 113 116
ND901
103
117
101
102
Ref. No. 101 102 103 104 105 106 107 108 109 110
Part No. 3-086-279-01 3-086-218-01 3-086-234-01 3-086-232-01 3-086-233-01 X-3953-782-1 3-086-199-01 3-086-198-01 3-086-200-01 1-478-171-11
Description TAPE (LCD) SCREW (M1.4), LOCK ASE, SPECIAL FRAME, LCD BUTTON, SW BUTTON, ZOOM CABINET (REAR) ASSY BASE, MODE KNOB, MODE SLIDER, MODE SWITCH BLOCK,CONTROL (PW-125)
Ref. No. 111 112 113 114 115 116 117 LCD901 MIC901 ND901
Part No. 3-086-277-01 3-086-274-01 3-086-278-01 3-086-206-01 3-086-207-01 3-088-260-01 3-090-940-01 8-753-052-81 1-542-554-11 1-478-250-11
Description CUSHION, MICROPHONE HOLDER, MICROPHONE SHEET, PROTECTION, HARNESS SHEET METAL, MODE RETAINER SPRING (MODE), CLICK SHEET (BL) SHEET (LCD) ACX500EN-J (2.5 INCH COLOR LCD UNIT) MICROPHONE BLOCK LIGHT GUIDE PLATE (2.5)
5-5
DSC-T1 CD-463
Ref. No. Part No.
CN-198
Description
ST-86
Ref. No. Part No. Description < LINE FILTER > LF001 1-456-583-11 COIL, COMMON MODE CHOKE < RESISTOR > R001 1-218-973-11 RES-CHIP 47K 5% 1/16W R002 1-218-977-11 RES-CHIP 100K 5% 1/16W R003 1-216-295-91 SHORT CHIP 0 R004 1-216-864-11 SHORT CHIP 0 ************************************************************ A-7078-867-A ST-86 BOARD, COMPLETE ******************** 0 1-478-385-11 LUMINOUS UNIT, STROBO SCOPE 1-860-515-11 FP-690 FLEXIBLE BOARD < CAPACITOR > DTC144EUA-T106 DTC144EUA-T106 DTC144EHT2L 2SC4250 (T5LSONY1) C002 0 C003 C004 1-162-970-11 CERAMIC CHIP 1-100-760-11 ELECT 1-137-723-21 CERAMIC CHIP < DIODE > 0.01uF 63uF 0.047uF 10% 99% 10% 25V 315V 250V
5-2. ELECTRICAL PARTS LIST
A-7111-623-A CCD BLOCK ASSY *************** not supplied CD-463 BOARD, COMPLETE ********************** (CD-463 board is included in CCD BLOCK ASSY.) < CAPACITOR > C001 C002 C003 C004 C005 1-107-826-11 1-107-826-11 1-107-826-11 1-164-845-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP < IC > IC001 not supplied CCD IMAGER (Note) < TRANSISTOR > Q001 Q002 Q003 Q004 8-729-029-14 8-729-029-14 8-729-052-64 8-729-050-22 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR < RESISTOR > R001 R002 R003 R004 R005 1-218-955-11 1-218-969-11 1-218-960-11 1-218-956-11 1-218-954-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 1.5K 22K 3.9K 1.8K 1.2K 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W D001 0 D002 D003 8-719-073-01 DIODE MA111-(K8).S0 6-500-237-01 DIODE HAU160C030TP 6-500-804-01 DIODE S4G49 (SONY) < TRANSISTOR > Q001 Q002 Q003 6-550-308-01 TRANSISTOR 8-729-056-01 TRANSISTOR 8-729-053-74 TRANSISTOR < RESISTOR > R001 R002 R003 R004 R005 R006 R007 R008 1-218-961-11 1-218-977-11 1-218-942-11 1-218-965-11 1-218-944-11 RES-CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP 4.7K 100K 120 10K 180 47 1M 1M 5% 5% 5% 5% 5% 5% 5% 5% 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W CPH3205-SONY-TL-E MCH3405-TL-E CY25AAJ-8-T13 0.1uF 0.1uF 0.1uF 5PF 0.1uF 10% 10% 10% 0.25PF 10% 16V 16V 16V 50V 16V
R006 1-218-990-11 SHORT CHIP 0 ************************************************************ A-7078-870-A CN-198 BOARD, COMPLETE ******************* < BATTERY > 0 BT001 1-528-999-51 BATTERY (LITHIUN BATTERY (SECONDARY)) < CAPACITOR > C001 1-164-874-11 CERAMIC CHIP < CONNECTOR > 100PF 5% 50V
1-216-805-11 METAL CHIP 1-216-857-11 METAL CHIP 1-216-121-11 RES-CHIP
< TRANSFORMER > CN001 1-816-929-11 CONNECTOR, MULTIPLE 26P < DIODE > D001 D002 D003 D004 D005 D009 8-719-077-54 8-719-077-57 8-719-077-57 8-719-077-57 8-719-077-57 8-719-077-57 DIODE DIODE DIODE DIODE DIODE DIODE MA4L11100AS0 DF3A8.2C (TPL3) DF3A8.2C (TPL3) DF3A8.2C (TPL3) DF3A8.2C (TPL3) DF3A8.2C (TPL3) 0 T002 1-437-987-31 TRANSFORMER , CONVERTER ************************************************************
Be sure to read "Precautions upon replacing CCD imager" on page 4-7 when changing the CCD imager. Note : The CCD imager is not supplied as a single unit since removing it as a single unit requires adjustment. CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
< FERRITE BEAD > FB001 FB002 FB003 1-500-284-21 INDUCTOR, FERRITE BEAD 1-500-284-21 INDUCTOR, FERRITE BEAD 1-414-228-11 INDUCTOR, FERRITE BEAD
5-6
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
LD-140
Ref. No. Part No. Description Ref. No. Part No. Description A-7078-877-A FP-695 BOARD, COMPLETE ********************** not supplied LD-140 BOARD, COMPLETE ********************** (LD-140 board is included in FP-695 board) ************************************************************ A-7078-865-A MS-148 BOARD, COMPLETE *********************** (CN402 is not included in this complete board.) ************************************************************ A-7079-000-A SY-MS BOARD, COMPLETE (SERVICE) ******************************* not supplied SY-95 BOARD, COMPLETE ********************* (MS-148 board and SY-95 board are included in SY-MS board.) (IC301 is not included in this complete board.) ************************************************************
MS-148
SY-95
Electrical parts list of the LD-140, MS-148 and SY-95 boards are not shown. Pages from 5-7 to 5-11 are not shown.
DSC-T1
Checking supplied accessories.
Make sure that the following accessories are supplied with your camcorder.
Power cord (Main lead) (1) (AUS model) 0 1-696-819-11 Power cord (Main lead) (1) (AEP, E model) 0 1-769-608-11 Power cord (Main lead) (1) (CH model) 0 1-782-476-13 Power cord (Main lead) (1) (UK, HK model) 0 1-783-374-11 Power cord (Main lead) (1) (JE model) 0 1-790-732-12 Power cord (Main lead) (1) (J model) 0 1-791-637-13 Power cord (Main lead) (1) (KR model) 0 1-776-985-11 Power cord (Main lead) (1) (US, CND model) 0 1-790-107-22
AC-LM5 AC Adaptor (1) (Except US, CND) 0 1-477-488-12 AC-LM5 AC Adaptor (1) (US, CND) 0 1-477-488-21
UC-TA USB cradle (1) 1-817-742-11
USB cable (1) 1-828-073-11
A/V connecting cable (1) 1-824-111-11 CD-ROM (USB Driver SPVD-013) (1) (AEP, UK, E, HK, AUS, CH, JE, KR model) 3-087-330-01 CD-ROM (USB Driver SPVD-013 (I)) (1) (US, CND, J model) 3-087-331-01
Wrist strap (1) 3-086-283-01
2-pin conversion adaptor (1) (JE model) 1-569-007-12
2-pin conversion adaptor (1) (E, HK model) 1-569-008-12
NP-FT1 battery pack (1) (not supplied)
"Memory stick Duo" (1) (MSA-M32A) (not supplied)
Memory stick Duo Adaptor(1) (MSAC-M2) (not supplied)
· Abbreviation CND : Canadian model AUS : Australian model CH : Chinese model HK : Hong Kong model KR : Korea model JE : Tourist model J : Japanese model
Other accessories
3-085-733-01 MANUAL, INSTRUCTION SET (JAPANESE) (J) 3-085-733-11 MANUAL, INSTRUCTION SET (ENGLISH) (EXCEPT KR, J) 3-085-733-21 MANUAL, INSTRUCTION SET (FRENCH/GERMAN) (CND, AEP) 3-085-733-31 MANUAL, INSTRUCTION SET (SPANISH/PORTUGUESE) (AEP, E, JE) 3-085-733-41 MANUAL, INSTRUCTION SET (ITALIAN/DUTCH) (AEP) 3-085-733-51 MANUAL, INSTRUCTION SET (CHINESE) (E, HK, CH, JE) 3-085-733-61 3-085-733-71 3-085-733-81 3-085-734-01 MANUAL, INSTRUCTION SET (RUSSIAN/SWEDISH) (AEP) MANUAL, INSTRUCTION SET (ARABIC) (E) MANUAL, INSTRUCTION SET (KOREAN) (JE, KR) MANUAL, INSTRUCTION (for PC)(JAPANESE) (J)
Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
5-12E
DSC-T1
9-876-280-32
Sony EMCS Co.
-- 52 --
2005F1600-1 ©2005.6 Published by DI Technical Support Department
DSC-T1
LEVEL
2 1
SERVICE MANUAL
Ver 1.1 2004.03
SUPPLEMENT-1
File this supplement-1 with the service manual. (PV03-016)
US Model Canadian Model AEP Model UK Model E Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model
· Addition of Black Model.
5. REPAIR PARTS LIST
Page Before change After change
: Added portion.
Checking supplied accessories.
5-12E
UC-TA USB cradle (1) 1-817-742-11 Wrist strap (1) 3-086-283-01 UC-TA USB cradle (1) 1-817-742-11 (SILVER) 1-817-742-21 (BLACK) Wrist strap (1) 3-086-283-01 (SILVER) 3-086-283-11 (BLACK)
DSC-T1
5-1. EXPLODED VIEWS
Page Before change After change
: Added portion.
5-1-1. OVERALL SECTION
Ref. No. 1 Part No. Description Ref. No. 1 1 7 Part No. Description X-3953-789-1 CABINET (FRONT) ASSY X-3953-789-1 CABINET (FRONT) ASSY (SILVER) X-2021-386-1 CABINET (FRONT) (B) ASSY (BLACK) 3-086-218-01 SCREW (M1.4), LOCK ASE, SPECIAL (SILVER) 3-086-218-11 SCREW (M1.4), LOCK ASE, SPECIAL (BLACK)
5-3
7
3-086-218-01 SCREW (M1.4), LOCK ASE, SPECIAL
7
5-1-2. BATTERY HOLDER SECTION
54 X-3953-783-1 HOLDER ASSY, BATTERY 3-086-210-01 LID, BT 3-086-217-01 CAP (MULTI) 54 54 56 56 68 68 X-3953-783-1 X-2021-390-1 3-086-210-01 3-086-210-11 3-086-217-01 3-086-217-11 HOLDER ASSY, BATTERY (SILVER) HOLDER (B) ASSY, BATTERY (BLACK) LID, BT (SILVER) LID, BT (BLACK) CAP (MULTI) (SILVER) CAP (MULTI) (BLACK)
5-4
56 68
5-1-3. CABINET (REAR) SECTION
104 105 106 3-086-232-01 BUTTON, SW 3-086-233-01 BUTTON, ZOOM X-3953-782-1 CABINET (REAR) ASSY 3-086-199-01 BASE, MODE 3-086-198-01 KNOB, MODE 1-478-171-11 SWITCH BLOCK,CONTROL (PW-125) 104 104 105 105 106 106 107 107 108 108 110 3-086-232-01 3-086-232-11 3-086-233-01 3-086-233-11 X-3953-782-1 X-2021-388-1 3-086-199-01 3-086-199-11 3-086-198-01 3-086-198-11 1-478-171-11 BUTTON, SW (SILVER) BUTTON, SW (BLACK) BUTTON, ZOOM (SILVER) BUTTON, ZOOM (BLACK) CABINET (REAR) ASSY (SILVER) CABINET (REAR) (B) ASSY (BLACK) BASE, MODE (SILVER) BASE, MODE (BLACK) KNOB, MODE (SILVER) KNOB, MODE (BLACK) SWITCH BLOCK,CONTROL (PW-125) (SILVER)
5-5
107 108 110
110
1-478-171-21 SWITCH BLOCK, CONTROL (PW-125) (BLACK)
9-876-280-83
Sony EMCS Co.
--2--
2004C1600-1 ©2004.3 Published by DI CS Strategy Div.
DSC-T1
LEVEL
2 1
SERVICE MANUAL
Ver 1.2 2004.03
SUPPLEMENT-2
File this supplement-2 with the service manual. (PV03-018)
US Model Canadian Model AEP Model UK Model E Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model
· Change of parts number. · Addition of Accessory.
5. REPAIR PARTS LIST
Page Before change
: Changed portion. After change
: Added portion.
Checking supplied accessories.
5-12E
CD-ROM (USB Driver SPVD-013) (1) (AEP, UK, E, HK, AUS, CH, JE, KR model) 3-087-330-01 CD-ROM (USB Driver SPVD-013 (I)) (1) (US, CND, J model) 3-087-331-01
CD-ROM (USB Driver SPVD-013) (1) (AEP, UK, E, HK, AUS, CH, JE, KR model) 3-087-330-11 CD-ROM (USB Driver SPVD-013 (I)) (1) (US, CND, J model) 3-087-331-11
UPDATE CD-ROM (PB), T1 3-091-965-01
9-876-280-86
Sony EMCS Co.
2004C1600-1 ©2004.3 Published by DI CS Strategy Div.
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar Printing a text
1. Click the Print button . 2. Specify a printer, print range, number of copies, and other options, and then click [OK].
Reversing the screens displayed once
· To reverse the previous screens (operation) one by one, click . the · To advance the reversed screens (operation) one by one, click the .
Application of printing:
To set a range to be printed within a page, select the graphic and drag on the page to enclose a range to selection tool be printed, and then click the Print button.
Application to the Service Manual:
This function allows you to go and back between circuit diagram and printed circuit board diagram, and accordingly it will be convenient for the voltage check.
Finding a text
1. Click the Find button . 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary)
Moving with link
1. Select either palm tool , zoom tool , text selection tool
Application to the Service Manual:
To execute "find" from current page toward the previous pages, select the check box "Find Backward" and then click the "Find".
, or graphic selection tool . 2. Place the pointer in the position in a text where the link exists (such as a button on cover and the table of contents page, or blue characters on the removal flowchart page or drawing page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:
Click an item (text) on the bookmark pallet, and you can move to the link destination. Also, clicking can display the hidden items. (To go back to original state, click ) 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.)
Application to the Service Manual:
The parts on the drawing pages (block diagrams, circuit diagrams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on the circuit diagram or printed circuit board diagram successively. Note: The find function may not be applied to the Service Manual depending on the date of issue.
Zooming or rotating the screen display
"Zoom in/out" · Click the triangle button in the zoom control box to select the display magnification. Or, you may click ing in or out. or for zoom-
Switching a page
· To move to the first page, click the · To move to the last page, click the · To move to the next page, click the . . . . "Rotate" · Click rotate tool , and the page then rotates 90 degrees each.
· To move to the previous page, click the
Application to the Service Manual:
The printed circuit board diagram you see now can be changed to the same direction as the set.
Reverse
987628036.pdf
Revision History
Ver. 1.0 1.1 1.2 1.3 Date 2003.10 2004.03 2004.03 2004.04 History Official Release Supplement-1 Supplement-2 Revised-1 Contents -- Addition of Black Model · Change of parts number. · Addition of Accessory. · Addition of Suplied parts. · Addtion of Error code. · Part number suffix of CD-463 board is changed to 12. Correction of repair parts list S.M. Correction: Page 5-3 Correction of repair parts list S.M. Correction: Page 5-3, 5-4 S.M. Rev. issued -- No No Yes
1.4 1.5
2005.04 2005.06
Correction-1 Correction-2
Yes Yes
DSC-T1