Text preview for : CDX-C5750.pdf part of Sony CDX-C5750 CDX-C5750
Back to : CDX-C5750.rar | Home
CDX-C5750/C5850
SERVICE MANUAL
US Model
CDX-C5750/C5850
Canadian Model
CDX-C5750
Photo: CDX-C5750
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS (US Model) POWER OUTPUT AND TOTAL HARMONIC DISTORTION 17 watts per channel minimum continuous average power into 4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than 1% total harmonic distortion. Other Specifications CD player section
System Signal-to-noise ratio Frequency response Wow and flutter Laser Diode Properties Material GaAlAs Wavelength 780 nm Emission Duration Continuous Laser output power Less than 44.6 µW* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pick-up Block. Compact disc digital audio system 90 dB 10 20,000 Hz Below measurable limit
Model Name Using Similar Mechanism CD Drive Mechanism Type Optical Pick-up Name
CDX-C480/C580 MG-363T-121 KSS-521A
Power amplifier section
Outputs Speaker outputs (sure seal connectors) Speaker impedance 4 8 ohms Maximum power output 40 W × 4 (at 4 ohms)
General
Outputs Line outputs (2) Power antenna relay control lead Power amplifier control lead Telephone ATT control lead Bass ±8 dB at 100 Hz Treble ±8 dB at 10 kHz 12 V DC car battery (negative ground) Approx. 178 × 50 × 185 mm (7 1/8 × 2 × 7 3/8 in.) (w/h/d) Approx. 182 × 53 × 162 mm (7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d) Approx. 1.2 kg (2 lb. 10 oz.) Parts for installation and connections (1 set) Front panel case (1)
Tone controls
Tuner section
FM
Power requirements Dimensions
Tuning range Antenna terminal Intermediate frequency Usable sensitivity Selectivity Signal-to-noise ratio
87.5 107.9 MHz External antenna connector 10.7 MHz 12 dBf 75 dB at 400 kHz 65 dB (stereo), 68 dB (mono) Harmonic distortion at 1 kHz 0.7% (stereo), 0.5% (mono) Separation 35 dB at 1 kHz Frequency response 30 15,000 Hz
AM
Mounting dimensions
Mass Supplied accessories
Design and specifications are subject to change without notice.
Tuning range 530 1,710 kHz Antenna terminal External antenna connector Intermediate frequency 10.7 MHz/450 kHz Sensitivity 30 µV
FM/AM COMPACT DISC PLAYER
MICROFILM
1
CDX-C5750/C5850
4-5. SCHEMATIC DIAGRAM -- CD MECHANISM SECTION -- · Refer to page 41 for IC Block Diagrams. · Refer to page 24 for Waveforms.
note: · Voltage and waveforms are dc with respect to ground under no-signal conditions. no mark : CD PLAY : Impossible to measure
27
28
(Page 33)
CDX-C5750/C5850
4-7. SCHEMATIC DIAGRAM -- MAIN SECTION (1/2) -- · Refer to page 41 for IC Block Diagrams.
(Page 28)
(Page 35)
note: · Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ( ) : AM < > : CD PLAY
33
34
CDX-C5750/C5850
4-8. SCHEMATIC DIAGRAM -- MAIN SECTION (2/2) -- · Refer to page 43 for IC Block Diagrams.
(Page 34)
(Page 39)
MB90574PFV-G-193-BND
note: · Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM ( ) : AM < > : CD PLAY
35
36
CDX-C5750/C5850
4-10. SCHEMATIC DIAGRAM -- DISPLAY SECTION --
(Page 36)
note: · Voltage is dc with respect to ground under no-signal (detuned) condition. no mark : FM
39
40
· IC Block Diagrams IC1 CXD2507AQ
XLON SPOD SPOC SPOB SPOA CLKO VDD XLTO DATO CNIN SEIN CLOK XLAT
IC402, 403 TDA8574 (CDX-C5850 only)
IC2 CXA1782BQ
PHD 2 PHD 1 RF M RF O
PHD
RF I
CC1
CC2 IIL
64 63 62 61 60 59 58 57 56 55 54 53 52 VCCL 1 INL 2 FOK MON MDP MDS LOCK TEST FILO FILI PCO VSS AVSS CLTV AVDD 1 2 3 4 5 6 7 8 9 10 11 12 13 SERVO AUTO SEQUENCER 5 51 50 49 48 47 46 45 44 43 42 41 40 DATA XRST SENS MUTE SQCK SQSO EXCK SBSO SCOR VSS WFCK EMPH SVRL 3 BUFFER BUFFER VCCL
36
35
34
33
32
31
30
29
28
27 26 25
16 CL+ 15 CL
14
CPU INTERFACE
SUB CODE PROCESSOR 4 DIGITAL CLV
LIFT AMP
REFERENCE
VCCL SIGNAL AMP
14 LGND
APC
LEVEL S
DIGITAL PLL
EFM DEMODULATOR
INML 4 VCCR INMR 5 SIGNAL AMP
13 OUTL
3 ASYMMETRY CORRECTOR 5 D/A INTERFACE DIGITAL OUT
CLOCK GENERATOR
FOK
12 OUTR 11 RGND
RF IV AMP1
MIRR DFCT
39 DOUT REFERENCE 38 37 36 35 34 C4M FSTT XTSL XTAO XTAI BUFFER SVRR 6 INR 7 VCCR 8 BUFFER VCCR LIFT AMP
FOK 24 23
LD
CP
CB
SENS C.OUT
RF BIAS ASYI ASYO ASYE
14 15 16 17 18
TTL
16K RAM
ERROR CORRECTOR 3
6
10 CR 9 CR+
RF IV AMP2 FE BIAS 37 TTL IIL DATA REGISTER INPUT SHIFT REGISTER ADDRESS DECODER FE AMP 20 IIL IIL OUTPUT DECODER 19 CLK XLT TTL 22 21 XRST DATA
WDCK 19
33 MNTO
20 21 22 23 24 25 26 27 28 29 30 31 32
LRCK PCMD BCLK GTOP XUGF XPCK VDD GFS RFCK C2PO XROF MNT3 MNT1
F
38 F IV AMP TOG1-3 BAL1-3 FZC COMP FS1-4 TG1-2 TM1-7 PS1-4
E
39
18
VCC
IC3 BA6796FP-T1
E IV AMP EI
OP IN OP IN + CH3-IN CH2-IN CH1-IN CH1 + CH1 VREF CH2 + CH2 VCC CH1 CH3 CH2
40 TE AMP BAL1 BAL 3 BAL2
28
27
26
25
24
23
22
21
20
19
18
17
16
15
HPF COMP
LPF COMP
LEVEL SHIFT
TRACKING PHASE COMPENSATION TM6
ISET
17
ISET
VCC LEVEL SHIFT
DRIVE BUFFER
DRIVE BUFFER
DRIVE BUFFER
DRIVE BUFFER
VEE
41 TG1 16 TOG1 TOG2 TOG3 SL O SL M TM5 TM4
TED 42
LEVEL SHIFT
15
THERMAL SHUT DOWN
LPFI 43 TEI 44 WINDOW COMP ATSC DFCT
TZC COMP
FCS PHASE COMPENSATION TM3 TM2 14 SL P
DFCT TM1 FS1 TM7 FS2 13 TA O
LEVEL SHIFT
ATSC 45 TZC 46
TDFCT 47 TG2
LOGIC CTL1 CTL2 FWD REV
V/I
DRIVE BUFFER
DRIVE BUFFER
DRIVE BUFFER
DRIVE BUFFER
DRIVE BUFFER
VC
48
FS4
1
OPOUT
2
CH4-IN
3
CH4
4
CTL1
5
CTL2
6
FWD
7
REV
8
TRAY
9
GND
10
CH5
11
COM
12
CH4 +
13
CH3 +
14
CH3
1 FEO
2 FEI
3 FDFCT
4 FGD
5 FLB
6 FE O
7 FE M
8 9 SRCH TGU
10 TG2
11 FSET
F SET
12 TA M
41
42
IC401 TDA7462D
PAUSE DETECT INPUT GAIN & AUTO ZERO TREBLE/ BASS CONTROL CIRCUIT FRONT FADER
28 27 26 25 24 23
SE3L SE3R MUTE SDA SCL PAUSE
SE1L SE1R MD+ MD CDL+ CDL CDR CDR+ PDR PDGND PDL SE2L SE2R
1 2 3 4 5 6 7 8 9 10 11 12 13
FRONT SIDE SELECTOR
LOUDNESS CONTROL CIRCUIT
VOLUME CONTROL CIRCUIT
SOFT MUTE
VOICE BANDPASS HP LP
22 OUT FL
INPUT MULTIPLEXER & MIXING STAGE
FRONT FADER COMPANDER REAR FADER LOUDNESS CONTROL CIRCUIT
21 OUT FR
REAR SIDE SELECTOR
20 OUT RL
INPUT GAIN
REAR FADER
19 OUT RR
BEEP
SUBWOOFER LP
FADER 18 SUBOUT+ 17 SUBOUT SDA
SUBWOOFER OUT IIC BUS
DIGITAL CONTROL CIRCUIT
SCL 16 VDD 15 GND
CREF 14
POWER SUPPLY
IC702 PCM1717E-S
IC901 BA4903
XTI DGND VDD
1 2 3
CLK CONTROL
20 XTO 19 CLKO
5.7V
LRCIN 4 DIN BCKIN ZERO 5 6 7
INPUT INTERFACE
18 ML/MUTE MODE CONT ROL 17 MC/DM1 16 MD/DM0 15 RSTB 14 MODE
ON +
ON +
DIGITAL FILTER
THERMAL SHUT DOWN
REGULATOR VREF
NOISE SHAPER 5LEVE DAC LOWPASS FILTER CMOS AMP 5LEVEL DAC LOWPASS FILTER CMOS AMP
1 AMP ON
CIRCUIT ON 2 AMP OUT 3 GND
OVER VOLTAGE PROTECT
4 VCC
D/C R
8
13 D/C L 12 VOUTL 11 VCC
5 VDD OUT
VOUTR 9 AGND 10
43
IC601 TDA7427AD1
28 LPOUT VDD1 LP FM LP HC LP AM V REF 1 2 3 4 INLOCK DETECTOR TEST LOGIC SWITCH LP1/LP2 CHARGE PUMP PHASE COMP 11 BIT PROG COUNTER SWITCH SWM/DIR 6 BIT PROG COUNTER SWITCH SWM/DIR PRE COUNTER :32/33 SWITCH AM/FM 27 VDD2 26 GND AM
25 AM IN
LCL/DX SEEK NIL MONO
5 6 7 8
24 FM IN
PORT EXTENSION
23 NC
OSCIN 9 OSCOUT 10 NC 11 SCL 12 SDA 13 BUS INTERFACE I2C
REF OSCILLATOR
16 BIT PROG COUNTER
SUPPLY & POWER ON RESET
22 GND D 21 VDD1 20 ADDR 19 HFREF 18 AMOSC
14 BIT PROG COUNTER
TIMER
CONTROL
SWITCH OUT
17 DOUT/INLOCK
IF AM 14
SWITCH AM/FM
11-21 BIT PROG COUNTER
16 SSTOP 15 IF FM
IC703 LC89170M-T
IC803 BA8270F-E2
VDD EXCK 1 14 VDD
BUS ON 1
BUS ON SWITCH RESET SWITCH BATTERY SWITCH
14 VCC
CPU INTERFACE
RST 2
SBSO 2 32 WORD X 8 BIT DUAL PORT RAM CRC CHECKER
13 DQSY
BATT 3
SCOR 3
12 SRDT
13 12 11 10
RST BUS ON CLK IN BU IN
WFCK 4
11 SCLK
MCK 5
XMODE 6 GND 7
TIMING & SYNCHRONIZATION SIGNAL PROTECTION
10 SW2
CLK 4 VREF 5 DATA 6 GND 7
9 DATA IN 8 DATA OUT
9 SW1
8 TEST
44
4-11. IC PIN DESCRIPTION
· IC801 MB90574PFV-G-193-BND (SYSTEM CONTROL) Pin No. Pin Name I/O 1 LD ON O Laser ON/OFF control output 2 3 4 5 6 7 8 9 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 48 49 50 51 52 53 54 55 FOK XLAT25 DATA25 XRST GFS NIL VCC NIL FLS SI/NOSE1 LCD SO/FLS SO LCD CKO BEEP NIL SQ SI NIL SQ CKO UNI SI UNI SO UNI CK C IN SIRCS TXT SI NIL TXT CKO CLOK25 SYSRST DEEMPH AMP ATT MD ON VSS C CD ON BUS ON AD ON DVCC DVSS NIL ANGLE AVCC AVRH AVRL AVSS KEY IN0 2 RC IN0 QUALITY NIL MPDH S-METER VCC NS MASK I O O O I -- -- -- I O O O -- I -- O I O I/O I I I -- O O O O O O -- -- O O O -- -- -- O -- -- -- -- I I I -- I I -- O Focus OK signal detection input CD signal processing latch output CD signal serial data output Reset output to CD signal processor IC. GFS signal detection input Not used. (Connect to ground in this set.) Power supply pin (+5 V) Not used. (Open) Front panel attachment detection input LCD serial data output LCD serial clock output BEEP output Not used. (Open) Sub Q data input Not used. (Connect to ground in this set.) Sub Q read clock output BUS system serial interface input BUS system serial interface output BUS system serial clock input/output Track jump No. count input Remote commander input CD-TEXT data input Not used. (Connect to ground in this set.) CD-TEXT data read clock output CD signal processing serial clock output System reset output De-emphasis output Power amplifier attenuator control output CD mechanism power control output Ground Power stabilization capacitor pin CD power control output BUS ON control output Power control output of A/D conversion. VREF input of D/A converter. Ground of D/A converter. Not used. (Open) LCD view angle alignment output (Not used in this set.) Analog power supply pin (+5 V) VREF + input of A/D converter. VREF input of A/D converter. Analog ground Key input 0 2 Rotary commander input 0 Not used in this set. Not used. (Connect to ground in this set.) Tuner multi path input (Not used in this set.) S-meter voltage detection input Power supply pin (+5 V) Not used in this set. Pin Description
45
Pin No. 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88, 89 90 91 92 93 94 95 96 97 98 99 100 101 102, 103 104 105 106, 107 108 109 110 111
Pin Name AMP ON TXT ON VOL ATT NIL ATT RC IN1 TU ATT VSS NIL SSTOP TEST DAVN FM ON/AM ON TU ON SDA SCL NOSE2 X1A X0A SCOR BU IN DQSY CD SENS KEY ACK TEL ATT ST/MONO SEEKOUT SD IN WIDE NARROW HSTX MD2 MD1, 0 RESET VSS X0 X1 VCC COM8V ON NIL AREA1 AREA2 AREA3 BAND ACC IN PH3, 2 LCD CE FLS W RE IN0, 1 ILL ON PW ON NIL ANT REM
I/O O O O -- O I O -- -- I I I O O I/O O I O I I I I I I I I/O O I O O -- -- -- I -- I O -- O -- I I I I I I O I I O O -- O
Pin Description Power amplifier power control output Reset output to CD-TEXT decoder IC. Electric volume mute control output Not used. (Open) System attenuate control output Rotary commander shift key input 1 Tuner attenuate output (Not used in this set.) Ground Not used. (Open) IF counter result signal detection input of PLL. Test mode initial setting detection input RDS IC data acquisition detection input (Fixed at "L" in this set.) FM ON output Tuner power control output I2C BUS serial data input/output I2C BUS serial clock output Front panel OPEN detection input (Not used in this set.) Sub ceramic oscillator output (32 kHz) Sub ceramic oscillator input (32 kHz) SCOR signal detection input Backup power detection input CD-TEXT data setting completion signal detection input CD SENS signal detection input Key input acknowledge Telephone attenuate detection input Tuner stereo signal detection input/forced monaural output SEEK output Signal detector input WIDE/NARROW select output (Not used in this set.) WIDE/NARROW select output (Not used in this set.) Hardware standby input (Connect to pin (ş (RESET).) Operation mode input (Connect to ground in this set.) Operation mode input (Connect to VCC in this set.) Reset input Ground Main ceramic oscillator input (4.19 MHz) Main ceramic oscillator output (4.19 MHz) Power supply pin (+5 V) COM 8V control output Not used. (Open) Destination select input 1 (Fixed at "L" in this set.) Destination select input 2 (Fixed at "L" in this set.) Destination select input 3 (Fixed at "L" (CDX-C5750) or "H" (CDX-C5850) in this set.) Not used in this set. Accessory power detection input Disc insertion detection photo sensor input (Not used in this set.) LCD chip enable output Flash write input (Fixed at "H" in this set.) Rotary encoder input Illumination power control output System power control output Not used. (Open) ANT REMOTE power control output
46
Pin No. 112, 113 114 115 116 117 118 119 120
Pin Name NIL CD LD CD EJ L SW IN SW/(PH1) D SW VSS SELF SW/(IN SW)
I/O -- O O I I I -- I
Pin Description Not used. (Open) Loading motor control output (Loading direction) Loading motor control output (Eject direction) Sled limit switch detection input Disc insertion detection input DOWN switch detection input Ground Disc self store detection input
47