Text preview for : AK56_SERVICE_MANUEL.pdf part of Vestel 11AK56 chassis Chassis 11AK56 Diagram+Service Manual



Back to : 11AK56.rar | Home

SERVICE MANUEL for 11AK56

Date Version Status Unit

: 16/01/2007 :1 : Draft : Electronic Hardware Design

VESTEL R&D Hardware Requirement Specification
11AK56

TABLE OF CONTENTS
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

1.
1.1. 1.2. 1.3.

INTRODUCTION .....................................................................................................4
Purpose ....................................................................................................................................4 Scope .......................................................................................................................................4 General Features .......................................................................................................................4

2.
2.1. 2.2.

GENERAL DESCRIPTION .....................................................................................4

Introduction ..............................................................................................................................4 System Building Blocks...............................................................................................................5 2.2.1. AK57 Chassis Block Diagrams 5 2.2.1.1. Genaral ...................................................................................................................5 2.2.1.2. SMPS ......................................................................................................................5 2.2.1.3. DEFLECTION ...........................................................................................................6 2.2.2. AK56 Chassis Main Blocks 6 2.2.2.1. UOC-II (ULTIMATE-ONE-CHIP).................................................................................7 2.2.2.2. Audio ....................................................................................................................15 2.2.2.3. External AV I/O .....................................................................................................17 2.2.2.4. TUNER..................................................................................................................18 2.2.2.5. SAW FILTERS ........................................................................................................19 2.2.2.5.1. K3958M (IF Filter for Video Applications).............................................................19 2.2.2.5.2. K9656M (IF Filter for Audio Applications) ............................................................20 2.2.2.5.3. K2966 (IF Filter for Intercarrier Applications).......................................................20 2.2.2.5.4. K2962 (IF Filter for Intercarrier Applications).......................................................21 2.2.2.5.5. G1975 (IF Filter for Intercarrier Applications) ......................................................21 2.2.2.6. SMPS ....................................................................................................................22 2.2.2.6.1. PRIMARY BLOCK ...............................................................................................22 2.2.2.6.1.1. SMPS CONTROLLER (UC3842)............................................................................23 2.2.2.6.1.2. MOSFET............................................................................................................24 2.2.2.6.1.2.1. MTP3N60E ......................................................................................................24 2.2.2.6.1.2.2. MTP6N60E ......................................................................................................25 2.2.2.6.2. SECONDARY BLOCK...........................................................................................25 2.2.2.6.3. SMPS Block Diagram ..........................................................................................27 2.2.2.7. DEFLECTION .........................................................................................................27 2.2.2.7.1. HORIZANTAL DEFLECTION ................................................................................27 2.2.2.7.2. MD1803DFX ......................................................................................................28 2.2.2.7.3. FBT...................................................................................................................30 2.2.2.7.4. AN15524A (VERTICAL DEFLECTION OUTPUT).....................................................32 2.2.2.8. CRT BOARD ..........................................................................................................34 2.2.3. AK56 Chassis Scematics 37 2.2.3.1. Part1 ....................................................................................................................37 2.2.3.2. Part2 ....................................................................................................................38 2.2.3.3. Part3 ....................................................................................................................39 2.2.3.4. Part4 ....................................................................................................................40 2.3. Service Menu...........................................................................................................................41 2.3.1. TUNER Settings 47 2.3.2. Adjustments 48

1

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

2

VESTEL R&D Hardware Requirement Specification
11AK56

Document History
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

Document Versi on Date Revision and Review History 16/01/2007 File Name: AK56_SERVICE_MANUEL Draft YALÇIN ELK SERDAR GÜLTEN Status Prepared by Approved by

3

VESTEL R&D Hardware Requirement Specification
11AK56

1. Introduction
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

1.1.

Purpose

This document is prepared for the UOCII TV project and describes the whole system features and operating principles to be used in hardware design phase. The document is based on "Device Specification UOCII-Version 1.12" from Philips Semiconductors. Prior to hardware design start, all parties involved must agree with the contents of this document.

1.2.

Scope

The document covers detailed descriptions of 11AK56 chassis system building blocks.

1.3.

General Features

11AK56 is a 90° / 50 Hz. chassis which is capable of driving 14"/20" superflat and 15" realflat CRT's . The chassis will have the following main features; · · · · · · · · · · · · · · · Remote Control 100 programs On Screen Display Mono Colour Standarts ; PAL, SECAM, NTSC, Transmission standarts ; B/G, L/L' I/I', DK, Teletext ; One pages or Seven Page Multi-standard alignment free PLL tuning, Europe Scart or Back AV input Detachable headphone output option, Front or side or AV input option, Back AV output option, 2W (%10 THD), 90-270V 50Hz or 170V-270V 50Hz SMPS Less than 3W or Less than 5W

2. General Description 2.1. Introduction

This chapter describes system building blocks and their detailed descriptions.
4

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

2.2.

11AK56

LINE_IN

DEGAUSING

LINE FILTER

VESTEL R&D Hardware Requirement Specification

System Building Blocks

2.2.1.2. SMPS

2.2.1.1. Genaral

SMPS IC

2.2.1. AK57 Chassis Block Diagrams

5

+6V

+11V

+5V_STB

+12V_A

VESTEL R&D Hardware Requirement Specification
11AK56

2.2.1.3. DEFLECTION
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

HORIZONTAL HORIZONTAL DRIVE
Horz. Yoke

30KV

FOCUS SCREEN

+33V Lin.

+8V +5V

+9V

Heater

-14V VERTICAL

+14V VERTICAL

30KV

CRT BOARD

Heater

G2

FOCUS

TRANSISTORS

RGB DRIVE

VERTICAL DRIVE

VERTICAL AMPLIFIER AN5524A

VERTICAL YOKE

2.2.2. AK56 Chassis Main Blocks
AK57 chassis main blocks are; · UOCII : Microcontroller + Video Proccessor + Sound Proccessor + IF + Teletext
6

VESTEL R&D Hardware Requirement Specification
11AK56

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

· · · · · · ·

AUDIO EXT. AV I/O TUNER SAW FILTERS SMPS DEFLECTION CRT BOARD

: Audio Amp., : Scart , AV input, AV output, : PLL Tuner : SMPS Controller, SMT, Bridge Rect., Line Filters : FBT, HOT, Vertical Amplifier, Line Driver, : RGB Amp. with transistors,

2.2.2.1. UOC-II (ULTIMATE-ONE-CHIP)
UOCII is composed of microcontroller, video proccessor, sound proccessor and IF blocks. The various versions of the TDA955X H/N1 series combine the functions of a video processor together with a microcontroller.The ICs are intended to be used in economy television receivers with 90 and 110 degree picture tubes. The ICs have supply voltages of 8V and 3.3V and they are mounted in a QFP 80 envelope. The features are given in the following feature list. FEATURES TV-signal processor · · · · · · · · · · · · · · Multi-standard vision IF circuit with alignment-free PLL demodulator Internal (switchable) time-constant for the IF-AGC circuit The QSS and mono FM functionality are both available so that an FM/AM TV receiver can be built without the use of additional ICs The mono intercarrier sound circuit has a selective FM-PLL demodulator which can be switched to the different FM sound frequencies (4.5/5.5/6.0/6.5 MHz). The quality of this system is such that the external band-pass filters can be omitted. The FM-PLL demodulator can be set to centre frequencies of 4.74/5.74 MHz so that a second sound channel can be demodulated. In such an application it is necessary that an external bandpass filter is inserted. The vision IF and mono intercarrier sound circuit can be used for the demodulation of FM radio signals Video switch with 2 external CVBS inputs and a CVBS output. One of the CVBS inputs can be used as Y/C input. 2 external audio inputs. The selection of the various inputs is coupled to the selection of the CVBS signals Integrated chrominance trap circuit Integrated luminance delay line with adjustable delay time Switchable group delay correction in the CVBS path Picture improvement features with peaking (with switchable centre frequency, depeaking, variable positive/negative overshoot ratio and video dependent coring), dynamic skin tone control and blue-, black- and white stretching Integrated chroma band-pass filter with switchable centre frequency
7

VESTEL R&D Hardware Requirement Specification
11AK56

· ·
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

· · · · · · · · · · · · · · ·

Switchable DC transfer ratio for the luminance signal Only one reference (12 MHz) crystal required for the m-Controller, Teletext- and the colour decoder PAL/NTSC or multi-standard colour decoder with automatic search system Internal base-band delay line Indication of the Signal-to-Noise ratio of the incoming CVBS signal A linear RGB/YUV/YPBPR input with fast blanking for external RGB/YUV sources. The synchronisation circuit can be connected to the incoming Y signal. The Text/OSD signals are internally supplied from the m-Controller/Teletext decoder. RGB control circuit with `Continuous Cathode Calibration', white point and black level offset adjustment so that the colour temperature of the dark and the light parts of the screen can be chosen independently. Contrast reduction possibility during mixed-mode of OSD and Text signals Adjustable `wide blanking' of the RGB outputs Horizontal synchronization with two control loops and alignment-free horizontal oscillator Vertical count-down circuit Vertical driver optimized for DC-coupled vertical output stages Horizontal and vertical geometry processing Horizontal and vertical zoom function for 16 : 9 applications Horizontal parallelogram and bow correction for large screen picture tubes Low-power start-up of the horizontal drive circuit

Microcontroller · · · · · · · · · · · · · · · 80C51 m-controller core standard instruction set and timing 1 ms machine cycle 32 - 128Kx8-bit late programmed ROM 3 - 12Kx8-bit DataRAM (shared between Display, Acquisition and Auxiliary RAM) Interrupt controller for individual enable/disable with two level priority Two 16-bit Timer/Counter registers One 16-bit Timer with 8-bit Pre-scaler WatchDog timer Auxiliary RAM page pointer 16-bit Data pointer Stand-by, Idle and Power Down modes 14 bits PWM for Voltage Synthesis Tuning 8-bit A/D converter with 4 multiplexed inputs 5 PWM (6-bits) outputs for control of TV analogue signals 18 general I/O ports

Data Capture · · · Text memory for 1 or 10 pages In the 10 page versions inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle Page Table (SPT) Data Capture for US Closed Caption

8

VESTEL R&D Hardware Requirement Specification
11AK56

· · · · · · · · ·

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

Data Capture for 525/625 line WST, VPS (PDC system A) and Wide Screen Signalling (WSS) bit decoding Automatic selection between 525 WST/625 WST Automatic selection between 625 WST/VPS on line 16 of VBI Real-time capture and decoding for WST Teletext in Hardware, to enable optimized mprocessor throughput Automatic detection of FASTEXT transmission Real-time packet 26 engine in Hardware for processing accented, G2 and G3 characters Signal quality detector for video and WST/VPS data types Comprehensive teletext language coverage Full Field and Vertical Blanking Interval (VBI) data capture of WST data

Display · · · · · · · · · · · · · · · · · · · Teletext and Enhanced OSD modes Features of level 1.5 WST and US Close Caption Serial and Parallel Display Attributes Single/Double/Quadruple Width and Height for characters Scrolling of display region Variable flash rate controlled by software Enhanced display features including overlining, underlining and italics Soft colours using CLUT with 4096 colour palette Globally selectable scan lines per row (9/10/13/16) and character matrix [12x10, 12x13, 12x16 (VxH)] Fringing (Shadow) selectable from N-S-E-W direction Fringe colour selectable Meshing of defined area Contrast reduction of defined area Cursor Special Graphics Characters with two planes, allowing four colours per character 32 software redefinable On-Screen display characters 4 WST Character sets (G0/G2) in single device (e.g. Latin, Cyrillic, Greek, Arabic) G1 Mosaic graphics, Limited G3 Line drawing characters WST Character sets and Closed Caption Character set in single device

Optional Used ICs at AK57 chassis are TDA9550 H/N1, TDA9551 H/N1, TDA9552 H/N1. FUNCTIONALOF TDA9550 H/N1 · · · · · · · · TV range is 90° Mono intercarrier multi-standard sound demodulator (4.5 - 6.5 MHz) with switchable centre frequency Audio switch Automatic Volume Levelling PAL decoder NTSC decoder ROM size 32 ­ 64K User RAM size 1K One page teletext
9

VESTEL R&D Hardware Requirement Specification
11AK56

·

Close Captioning

FUNCTIONALOF TDA9551H
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

· · · · · · · · · ·

TV range is 90° Mono intercarrier multi-standard sound demodulator (4.5 - 6.5 MHz) with switchable centre frequency Audio switch Automatic Volume Levelling PAL decoder SECAM decoder NTSC decoder ROM size 32 ­ 64K User RAM size 1K One page teletext Close Captioning

FUNCTIONALOF TDA9552H · · · · · · · · · · · · TV range is 90° Mono intercarrier multi-standard sound demodulator (4.5 - 6.5 MHz) with switchable centre frequency Audio switch Automatic Volume Levelling QSS sound IF amplifier with separate input and AGC circuit AM sound demodulator without extra reference circuit PAL decoder SECAM decoder NTSC decoder ROM size 32 ­ 64K User RAM size 1K One page teletext Close Captioning

10

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

11

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

BLOCK DIAGRAM

12

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

PINING

13

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

14

VESTEL R&D Hardware Requirement Specification
11AK56

2.2.2.2. Audio
The TDA2822 is DUAL LOW-VOLTAGE POWER AMPLIFIER.
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

· · · ·

Supply voltage down to 1.8V Low crossover distorsion Low quiescent current Bridge or stereo configuration

ELECTRICALCHARACTERISTICS

15

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

Figure: Test Circuit (Bridge)

Figure: Test Circuit (Stereo)

16

VESTEL R&D Hardware Requirement Specification
11AK56

Figure: Application in 11AK56

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

2.2.2.3. External AV I/O
SCART PINING 1. Audio right output 2. Audio right input 3. Audio left output 4. Ground AF 5. Ground Blue 6. Audio left input 7. Blue input 8. AV switching input 9. Ground Green 10. Not Used 11. Green input 12. Not Used 13. Ground Red 14. Ground Blanking 15. Red input 16. Blanking input 17. Ground CVBS output 18. Ground CVBS input 19. CVBS output 20. CVBS input 21. Ground 0.5Vrms / 1K 0.5Vrms / 10K 0.5Vrms / 1K 0.5Vrms / 10K 0.7Vpp / 75 0-12VDC /10K 0.7Vpp / 75

0.7Vpp / 75 0-0.4VDC, 1-3VDC / 75 1Vpp / 75 1Vpp / 75

17

VESTEL R&D Hardware Requirement Specification
11AK56

Front/Side/Back AV Input
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

Audio Video

0.5Vrms / 10K 1Vpp / 75

Back AV Output Audio Video 0.5Vrms / 1K 1Vpp / 75

2.2.2.4. TUNER
Channel coverage of PLLTuner for VHF/UHF OFF-AIR CHANNELS BAND Low Band Mid Band High Band FREQUENCY CHANNELS RANGE (MHz) E2 to C E5 to E12 E21 to E69 48.25 to 82.25 (1) 175.25 to 224.25 471.25 to 855.25 (2) CABLE CHANNELS CHANNELS S01 to S08 S09 to S38 S39 to S41 FREQUENCY RANGE (MHz) 69.25 to 154.25 161.25 to 439.25 447.25 to 463.25

(1). Enough margin is available to tune down to 45.25 MHz. (2). Enough margin is available to tune up to 863.25 MHz.

Noise Low band : Mid band : High band :

Typical Max. 5dB 9dB 5dB 9dB 6dB 9dB

Gain Min. Typical Max. All channels : 38dB 44dB 52dB Gain Taper (of-air channels): 8dB

Noise is typically 6dB for all channels. Gain is minimum 38dB and maximum 50dB for all channels. Terminals for External Connection

18

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

Electrical conditions

VESTEL R&D Hardware Requirement Specification

· · · ·

Standard

B/G D/K I L/L'

2.2.2.5. SAW FILTERS

2.2.2.5.1.

K3958M (IF Filter for Video Applications)

19

VESTEL R&D Hardware Requirement Specification
11AK56

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

Pin configuration 1 Input 2 Input - ground 3 Chip carrier - ground 4 Output 5 Output Features · · TV IF video filter with Nyquist slopes at 33.90 MHz and 38.90 MHz Constant group delay

2.2.2.5.2.
Standard · · · · B/G D/K I L/L'

K9656M (IF Filter for Audio Applications)

Pin configuration 1 Input 2 Input - ground 3 Chip carrier - ground 4 Output 5 Output Features · · · TV IF audio filter with two channels Channel 1 (L') with one pass band for sound carriers at 40,40 MHz (L') and 39,75 MHz (L'- NICAM) Channel 2 (B/G, D/K, L, I) with one pass band for sound carriers between 32,35 MHz and 33,40 MHz

2.2.2.5.3.
Standard · · B/G D/K

K2966 (IF Filter for Intercarrier Applications)

Pin configuration 1 Input 2 Input - ground 3 Chip carrier - ground
20

VESTEL R&D Hardware Requirement Specification
11AK56

4 5
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

Output Output

Features · · · TV IF filter with Nyquist slope and sound shelf Broad sound shelf for sound carriers at 32,40MHz and 33,40 MHz Group delay predistortion

2.2.2.5.4.
Standard · · · B/G I L/L'

K2962 (IF Filter for Intercarrier Applications)

Pin configuration 1 Input 2 Input - ground 3 Chip carrier - ground 4 Output 5 Output Features · · · · TV IF filter with two Nyquist slope and sound shelf Picture carriers at 33,90 MHz and 38,90 MHz Broad sound shelf at 15 dB level for sound carriers at 32,90 MHz and 33,40 MHz Constant group delay

2.2.2.5.5.
Standard · B/G

G1975 (IF Filter for Intercarrier Applications)

Pin configuration 1 Input 2 Input - ground 3 Chip carrier - ground 4 Output 5 Output Features · · TV IF filter with Nyquist slope and sound shelf Picture carrier at 38.90MHz
21

VESTEL R&D Hardware Requirement Specification
11AK56

·

Reduced group delay predistortion as compared with standard B/G, half

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

2.2.2.6. SMPS 2.2.2.6.1. PRIMARY BLOCK

AC power applied via AC inlet, line filter components prevent chassis from incoming noise of AC line, also prevents AC line against created noises by TV. Bridge rectifier and bulk capacitor converts AC voltage to DC voltage. Applied DC voltage to primary winding is then swicthed via MOSFET by primary controller in a controlled manner. SMPS controller works on quasi-resonant PWM and gets first supply voltage from AC line (SMPS Controller supply). Controller drives MOSFET according to feedback information supplied by shunt regulator and opto-coupler, according to that information adjusts on-time of MOSFET for required power. After the start-up in normal operation mode SMPS controller is supplied by SMT. Primary block consist of following main parts, AC Inlet (PL800), Fuse (F800), Varistor (R800), Line Filter For EMC (C801,L800,C800), SMPS Controller (IC801), SMPS Controller supply for first Start-up (R807), Bridge Rectifier (D811,D813,D814,D816), Rectifier For SMPS Controller(D801), Bulk Cap (C806), Clamping Circuitry (R809,C812,C813,C817), SMT (Switch Mode Transformer) (TR800), SMT Driver MOSFET (Q800), Current Sense Resistor (R812), Protection Components for MOSFET Failure (D815,D812,R811)

22

VESTEL R&D Hardware Requirement Specification
11AK56

2.2.2.6.1.1.

SMPS CONTROLLER (UC3842)

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

TheUC3842 of control IC providesthe necessary features to implement off-line or DC to DC fixed frequency current mode controlschemes witha minimal externalparts count. Internallyimplemented circuit sincludeundervoltagelockout featuring start-up current less than 1 mA, a precision reference trimmed for accuracy at the erroramp input, logic to insure latched operation, a PWMcomparatorwhichalso providescurrentlimit control,anda totem pole output stage designed to source or sink high peak current. The output stage, suitable for driving NChannelMOSFETs, is low in theoff-state. Differencesbetweenmembers of this family are the under-voltage lockout thresholds and maximum duty cycle ranges. The UC3842 has UVLO thresholds of 16V (on) and 10V (off), ideally suited off-line applications. The UC3842 can operate to duty cycles approaching 100%. Features · · · · · · · · · · · Optimized for off-line and dc to dc converters Low start-up current (< 1 ma) Automatic feed forward compensation Pulse-by-pulsecurrent limiting Enhanced load response characteristics Under-voltage lockout withhysteresis Double pulse suppression High current totempole output Internally trimmed bandgap reference 500Khz operation Low Ro erroramp

Block Diagram

23

VESTEL R&D Hardware Requirement Specification
11AK56

ABSOLUTE MAXIMUMRATINGS

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

2.2.2.6.1.2.

MOSFET

The MTP3N60E used for voltage range 170-270V, The MTP6N60E used for voltage range 90 ­ 270V. 2.2.2.6.1.2.1. MTP3N60E

N­Channel Enhancement­Mode Silicon Gate This advanced high voltage TMOS E­FET is designed to with stand high energy in the avalanche mode and switch efficiently. This new high energy device also offers a drain­to­ source diode with fast recovery time. Designed for high voltage, high speed switching applications such as power supplies, PWM motor controls and other inductive loads, the avalanche energy capability is specified to eliminate the guesswork in designs where inductive loads are switched and offer additional safety margin against unexpected voltage transients. Avalanche Energy Capability Specified at Elevated Temperature Low Stored Gate Charge for Efficient Switching Internal Source­to­Drain Diode Designed to Replace External Zener Transient Suppressor -- Absorbs High Energy in the Avalanche Mode Source­to­Drain Diode Recovery Time Comparable to Discrete Fast Recovery Diode

24

VESTEL R&D Hardware Requirement Specification
11AK56

2.2.2.6.1.2.2.

MTP6N60E

N­Channel Enhancement­Mode Silicon Gate
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

This high voltage MOSFET uses an advanced termination scheme to provide enhanced voltage­blocking capability without degrading performance over time. In addition, this advanced TMOS E­FET is designed to withstand high energy in the avalanche and commutation modes. The new energy efficient design also offers a drain­to­source diode with a fast recovery time. Designed for high voltage, high speed switching applications in power supplies, converters and PWM motor controls, these devices are particularly well suited for bridge circuits where diode speed and commutating safe operating areas are critical and offer additional safety margin against unexpected voltage transients. · · · · · Robust High Voltage Termination Avalanche Energy Specified Source­to­Drain Diode Recovery Time Comparable to a Discrete Fast Recovery Diode Diode is Characterized for Use in Bridge Circuits IDSS and VDS(on) Specified at Elevated Temperature

2.2.2.6.2.

SECONDARY BLOCK

Switching primary winding of SMT induces voltages to secondary windings of SMT. Induced voltages are then rectified by secondary recitification diodes and capacitors. Secondary block consist of following main parts, Optocoupler for sensing stand-by (IC805), Rectifier and DC line Components for B+ (C821,C822,C824,C832,D804,L804,R815), Audio +12 Supply Rectifiers and DC line Components (C831,C826,C827,C828,C831,R814,D807)
25

VESTEL R&D Hardware Requirement Specification
11AK56

+ 11 Supply Rectifiers and DC line Components (D806,C823,C825),
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

+

6V Controller Supply (D805,C826,C830),

Rectifiers

and

DC

line

Components at Stand by Mode

20 21 18 19 SMT 17 15 14 16 13

150V / 800mA GND +13,5V / 1,5A GND - 13,5V / 1,5A + 14V / 1A 8V / 1A GND 22V / 800mA

Power Supply Performance
USABLE MIN & MAX OPERTAING VOLTAGES (170 V- 270V) DROP OUT VOLTAGE START UP VOLTAGE POWER CONSUMPTION SMPS OUTPUT VOLTAGES SMPS FET DRAIN VOLTAGE SMPS FET GATE VOLTAGE SMPS FET OPERATING FREQUENCY 170 V. min , 270 V. max 155 V. 170 V. < 1W in Stand-by, 160W max. ± 0,5 V. of design value % 90 of MOSFET spec. % 90 of MOSFET spec. Fix

26

VESTEL R&D Hardware Requirement Specification
11AK56

2.2.2.6.3.
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

SMPS Block Diagram

DEGAUSING

LINE FILTER LINE_IN

+6V +5V_STB

+12V_A

SMPS IC
+11V

2.2.2.7. DEFLECTION
2.2.2.7.1. HORIZANTAL DEFLECTION

Deflection block consist of following main parts, Horizontal driver transistor (Q600), Horizontal driver (L600), HOT (Horizontal Output Transistor) (Q603), FBT (TR600), Linearity Coil (L601), Flyback Capacitors (C611), S-correction capacitor (C622), Modulated S-correction capacitor (C623), Hdrive signal is buffered and applied to line driver transistor by a capacitor. Line driver produces necessary base currents, parallel diode to base series resistor speeds up the reverse base current. UOCII has soft-start and soft-stop features to have more safe operation. There are two base current adjustment resistors on the circuit. Collector current differs according to CRT sizes .
27

VESTEL R&D Hardware Requirement Specification
11AK56

Tube dependent components are choosen to fit best picture performance by keeping; 11-12usec. Flyback time, Max. 1300V. collector voltage (peak-detect mode measurement)
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

2.2.2.7.2.

MD1803DFX

HIGH VOLTAGE NPN POWER TRANSISTOR FOR STANDARD DEFINITION CRT DISPLAY Features · · · · · · · State-Of-The-Art Technology: ­ Diffused collector "ENHANCED GENERATION" More stable performance versus operating temperature variation Low base drive requirement Tighter hFE range at operating collector current Fully insulated power package U.L. compliant Integrated free wheeling diode In compliance eith the 2002/93/EC EUROPEAN DIRECTIVE

28

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

29

VESTEL R&D Hardware Requirement Specification
11AK56

2.2.2.7.3.

FBT

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

Operating Ampient Temperatue : -10°C..........+60°C Stroge Ampient Temperature : -20°C..........+80°C Operating Horizantal Frequency : 15.625KHz ±0.5KHz INDUCTANCE (Between pin1 to pin3) : 3.02mH ± %8 INTERNAL RESISTANCE : Max. 2.2Ohm Regulation:Max.%10 FLYBACK TIME : 11.5µsec COLLECTOR VOLTAGE : 1000Vp_p FOCUS VOLTAGE RANGE % OF EHT: min.18.2 max.34.6 DEFLECTION CURRENT : 3.1Ap_p max.

AUXLIARY OUTPUTS: Heater Voltage : 6.3Vrms / max 750mA RGB Supply : +200V / max 30mA ±%5
Vertical Supply : +14V / max 1A ±%5 Vertical Supply : -14V / max 1A ±%5 Auxliary Voltage : +9V / max 1A ±%5

Tuning Voltage : +33V max 100mA ±%5

30

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

31

VESTEL R&D Hardware Requirement Specification
11AK56

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

2.2.2.7.4.

AN15524A (VERTICAL DEFLECTION OUTPUT)

The AN5524A (TV vertical deflection output circuit) is a monolithic integrated circuit designed for vertical deflection output, such as TV and display. Features · · · · Built-in Pump-up circuit Built-in Thermal protection circuit Maximum deflection current = 1.6Ap-p Dimple forming type : Advantages : a) Withstand repeated movements between the body and the solder joint of the IC (when a heat-sink is used). b) Better vibration absorber (eg. CTV installed in the bus/coach). VCC operating range : 12V ~ 30V

·

32

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

33

VESTEL R&D Hardware Requirement Specification
11AK56

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

2.2.2.8. CRT BOARD
Transistors are used for amplifying RGB signals. 2SC2482 For High Voltage Switching And Amplifier Applications: · · High Voltage : V(BR)=300V. Small Collector Output Capacitance : Cob=3.0pF (typ.)

34

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

35

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

36

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

2.2.3. AK56 Chassis Scematics
2.2.3.1. Part1

VESTEL R&D Hardware Requirement Specification

37

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

2.2.3.2. Part2

38

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

2.2.3.3. Part3

39

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

11AK56

VESTEL R&D Hardware Requirement Specification

2.2.3.4. Part4

40

VESTEL R&D Hardware Requirement Specification
11AK56

2.3.
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

Service Menu
OSD FAPS Definition First APS

To enter the Service Nenu, open main menu and press 4, 7, 2, 5 buttons from remotecontrol.
S-No 001

Possible Settings
ON = Active OFF = In-active

Default OFF

002 003

ISPM INIT

I2C Mode Resetting software and hardware

OFF ON = Enable resetting OFF = Disable resetting

OFF OFF

Table 1 Init

S-No 004

OSD AGCSPD

Definition IF AGC speed

Possible Settings
0 1 2 3 = = = = Slow Standard Fast Fastest

Default 1

005

AGCTO

AGC Take over

0..63

31

Table 2 AGC Service settings

S-No 006

OSD COFF

Definition Cut-Off setting

Possible Settings
0..63

Default 32

Table 3 VG2 Alignment Service settings
S-No 007 008 009 010 011 OSD VERT SLOP SCORRECTION VERT SHIFT VERT AMP HOR SHIFT Definition Vertical slope (VSL), SBL bit should be keyed to half-blank. S-correction 4:3 vertical shifting for Wide Screen Vertical Amplitude Horizontal shifting

Possible Settings
0..63 0..63 0..63 0..63 0..63

Default 32 32 32 32 32

41

VESTEL R&D Hardware Requirement Specification
11AK56

S-No 012
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

OSD VERT SHIFT16 VERT AMP16 RGB HSH RGB HSH60 60HZ HSH 43 60HZ VSH 43 60HZ VA 43 60HZ VSH 169 60HZ VA 169

Definition 16:9 vertical shifting for Wide Screen 16:9 Horizontal amplitude In RGB mode with 50 Hz, horizontal shifting In RGB mode with 60 Hz, horizontal shifting In 4:3 MODE with 60 Hz, horizontal shifting In 4:3 MODE with 60 Hz, vertical shifting In 4:3 MODE with 60 Hz, vertical amplitude In 16:9 MODE with 60 Hz, vertical shifting In 16:9 MODE with 60 Hz, vertical amplitude

Possible Settings
0..63 0..63 0..63 0..63 0..63 0..63 0..63 0..63 0..63

Default 32 32 37 37 31 31 31 31 31

013 014 015 016 017 018 019 020

Table 4 Geometry Service settings
SNo 021 OSD QSS Definition

Possible Settings
ON = QSS Active OFF = QSS InActive 0..63

Default ON

Switching the mode of the QSS amplifier

022

OIF

DC offset correction at IF-PLL

29

023

IF

PLL demodulator frequency

024

OFR

Frequency Entry Activation: Frequency mode which is value Tuning Mode item on the Installation menu can be enabled or disabled by OFR. )

0 = 58.75 MHz 1 = 45.75 MHz 2 = 38.90 MHz 3 = 38.00 MHz 4 = 33.40 MHz 5 = 42.00 MHz 6 = 33.90 MHz 7 = 48.00 MHz 8 = EXTERNAL ON = Active OFF = In-Active

2

ON

025

FFI

Fast filter IF-PLL

026

BS1

Please look at the related Tuner specification for necessary adjustments.

ON = Fast time constant OFF = Normal time constant 0..15

OFF

1

42

VESTEL R&D Hardware Requirement Specification
11AK56

SNo 027
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

OSD BS2 BS3 CB B1-H B1-L B2-H B2-L

Definition Please look at the related Tuner for necessary adjustments. Please look at the related Tuner for necessary adjustments. Please look at the related Tuner for necessary adjustments. Please look at the related Tuner for necessary adjustments. Please look at the related Tuner for necessary adjustments. Please look at the related Tuner for necessary adjustments. Please look at the related Tuner for necessary adjustments. specification specification specification specification specification specification specification

Possible Settings
0..15 0..15 0..255 0..255 0..255 0..255 0..255

Default 2 4 142 12 32 30 2

028 029 030 031 032 033

Table 5 Tuning Service settings
S-No 034 OSD FRAV Definition For AV, Peaking center frequency

Possible Settings
0 = 2.7 Mhz 1 = 3.1 Mhz 2 = 3.5 Mhz 0..15

Default 1

035

YSCM

For SECAM, Y-delay setting

12

036

YNTS

For NTSC, Y-delay setting

0..15

2

037

YPAL

For PAL, Y-delay setting

0..15

2

038

YAV1

For AV-1, Y-delay setting

0..15

4

039

YSVHS

For S-VHS-2, Y-delay setting

0..15

4

Table 6 Video Service settings
SNo 040 041 042 043 044 045 046 047 048 049 050 OSD WPRC WPGC WPBC BLORB BLOG WPRN WPGN WPBN BLRB-RGB BLG-RGB WPRW Definition For Cold, White point Red For Cold, White point Green For Cold, White point Blue Black level offset Red ­ Blue Black level offset Green For Normal, White point Red For Normal, White point Green For Normal, White point Blue For RGB, Black level offset Red ­ Blue For RGB, Black level offset Green For Warm, White point Red

Possible Settings
0..63 0..63 0..63 0..63 0..63 0..63 0..63 0..63 0..63 0..63 0..63

Default 32 32 31 32 32 37 32 19 32 32 49

43

VESTEL R&D Hardware Requirement Specification
11AK56

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

SNo 051 052 053 054 055 056 057

OSD WPGW WPBW BLRB-YUV BLG-YUV WPRWRGB WPGWRGB WPBWRGB

Definition For For For For For Warm, White point Green Warm, White point Blue YUV, Black level offset Red ­ Blue YUV, Black level offset Green RGB, White point Red

Possible Settings
0..63 0..63 0..63 0..63 0..63 0..63 0..63

Default 40 25 32 32 32 40 32

For RGB, White point Green For RGB, White point Blue

Table 7 White tone adjustments
SNo 058 OSD OSO Definition Switch-off at vertical overscan

Possible Settings
ON = Enable Switchoff OFF = Disable Switchoff ON = Vertical slicing

Default ON

059

FSL

For vertical sync, Forced Slicing level

OFF

level fixed to 60% of sync amplitude OFF = Automatic vertical slicing level
060 PN8-STB If option is ON TV can open from stanby when PIN8 is activated OFF = feature is not avaliable ON = feature is avaliable 0..15 ON = Bypass OFF

061 062

PWL BPS

Peak white limiting Bypass chroma base-band

8 OFF

baseband chroma delay line OFF = Baseband chroma delay line active
063 CLPL Soft clipping level 0 = 0% above PWL 1 = 5% above PWL 2 = 10% above PWL 3 = Off 0..15 ON = last minute 0

064 065

CL ST-LMI

Cathode drive level Option for sleep timer last minute indicator

10 OFF

indicator appears on TV OFF = last minute indicator does not appear on TV

44

VESTEL R&D Hardware Requirement Specification
11AK56

SNo 066
© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

OSD DNMENU

Definition Dynamic Menu Mode

Possible Settings
ON = Dynamic Menu Enable OFF = Dynamic Menu Disable

Default OFF

067

OPC

Point black current system

ON = 1 point black current system OFF = 2 point black current system

OFF

Table 8 8 Bit Control Service settings
SNo 068 069 070 071 072 073 074 OSD FAVI BAVI BSVI SSTDB G SSTDI SSTDD K SSTDL Definition FAV BAV SVHS BG sound standard I sound standard DK sound standard L- L prime sound standard

Possible Settings
ON = Active OFF = In-active ON = Active OFF = In-active ON = Active OFF = In-active ON = Active OFF = In-active ON = Active OFF = In-active ON = Active OFF = In-active ON = Active OFF = In-active

Default ON OFF OFF ON ON ON ON

Table 9 Source Switching Service settings

SNo 075 076 077 078 079 080

OSD TXHPO S TXTBRI TXTCO N LSEL1 LSEL2 -------

Definition One page Teletext starting point setting Teletext brightness setting Teletext contrast setting Menu language setting Menu language setting

Possible Settings
0..20 0..63 0..15 0..255 0..255

Default 10 32 0 255 255

Table 10 Teletext Service settings

45

VESTEL R&D Hardware Requirement Specification
11AK56

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

SNo 081

OSD PWPR F PWRE S

Definition According to video and sound, when TV opening, fast startup and perfect startup Opens from STANDBY.

Possible Settings
0..15 0 = Fast 15 = Perfect ON = Opens depending on the last state OFF = Opens from STANDBY

Default 10

082

ON

Table 11 Power Service settings
SNo 083 084 085 086 OSD MAXCOL MAXBRI MINBRI MAXCON Definition Maximum color setting limiter at Picture menu Maximum brightness setting limiter at Picture menu Minimum brightness setting limiter at Picture menu Maximum contrast setting limiter at Picture menu

Possible Settings
0..63 0..63 0..63 0..63

Default 50 57 20 50

Table 12 Picture Service settings

SNo 087 088 089

OSD SAVEFS LOADFS OAVL

Definition Saving Factory settings Loading Factory setting OAVL = 0 (AVL is off and AVL line is not avaliable in sound menu) OAVL = 1 (AVL line is avaliable in sound menu) OAVL = 2 (AVL is on and AVL line is not avaliable in sound menu) Other values of OAVL work like OAVL =1 Selection for hotel mode search HTLSRC = 0 (TV) HTLSRC = 1 (AV) HTLSRC = 2 (FAV) HTLSRC = 3 (SVHS) HTLSRC > 3 (HOTEL MODE NOT AVAILABLE) Maximum volume for hotel mode Volume level definition for hotel mode when tv is openning Preover Shoot Ratio PSYS_RATIO_PRE_OVERSHOOT_MIN =0 PSYS_RATIO_PRE_OVERSHOOT_MAX =3

Possible Settings
OFF OFF 0-63

Default OFF OFF 32

090

HTLSRC

0-63

32

091 092 093

HMAXVO L HDEFVO L RPO

0-63 0-63 0-3

32 32 32

46

VESTEL R&D Hardware Requirement Specification
11AK56

094

PF

© Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

095

APSSND

Peaking Frequency PF1-PF0 = 0 (2.7 Mhz) 1 (3.1 Mhz) 2 (3.5 Mhz) 3 (spare) Default value of sound standard in APS menu 0-> BG 1-> I 2-> DK 3-> L\L'

0-3

2

0-3

0

Table 13 Factory Service settings

2.3.1. TUNER Settings
AK56 SERVICE MENU ITEMS

B1-H Philips UV1316S MK3 LG TAEW-G002D Thomson CTT5020 Samsung TECC2949PG28B Samsung TECC2949PG35B Alps TEDE9X226A Alps TEDE9-004A Samsung TECC2949PG40B Samsung TECC2949PS40B 12 11 9 13 13 11 11 11 11

B1-L 50 82 146 18 18 82 194 82 82

B2-H 30 29 27 31 30 29 28 29 29

B2-L 2 2 130 130 130 2 242 2 2

BS1 1 1 3 1 1 1 1 1 1

BS2 2 2 6 2 2 2 2 2 2

BS3 4 8 133 4 8 8 8 8 8

CB 142 142 142 142 142 142 142 142 142

47

VESTEL R&D Hardware Requirement Specification
11AK56

Explanations © Copyright 2003 VESTEL Group of Company All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written permission from VESTEL

B1H B1L B2H B2L BS1 BS2 BS3 CB

High byte of VHF1-VHF3 cross-over frequency Low byte of VHF1-VHF3 cross-over frequency High byte of VHF3-UHF cross-over frequency Low byte of VHF3-UHF cross-over frequency Band switching byte for VHF1 Band switching byte for VHF3 Band switching byte for UHF Control byte

2.3.2. Adjustments
Geometry Adjustment: After adjusting 50Hz geometry items (between 007-011). NTSC 60 Hz geometry items (between 016-018) should be adjusted to determine NTSC 60Hz offset. NTSC offset is automatically calculated and stored in NVM. Later on, if we need to change 50Hz geometry settings, NTSC 60Hz geometry settings is automatically calculated by using NTSC offset. 16:9 mode geometry adjustment works like NTSC 60Hz geometry adjustment. If press to menu button between 007-011 or 016-018 items. New geometry setting is stored and, 16:9 mode, RGB shift and NTSC geometry automatically calculated. RGB shift offset value is stored in software. Only NTSC offset and 16:9 mode offset values are stored in EEPROM. AGC adjustment: Connect to tuner 60db broadcast and, press to blue button on AGCTO item. AGC is automatically adjusted. Screen Adjustment: When yellow button is pressed in service menu. Vertical scan is disabled and related registers are updated. Thin line will be appeared on the screen. Then the screen potentiometer is gently adjusted until the thin line will be lightly disappeared When press to yellow button again, old register values are reloaded and vertical scan is enabled. FOCUS Adjustment: TV is tuned to the signal. Then focus potantiometer (the upper pot on the rear side of the FBT transformer) is adjusted for optimum focusing drive.

48