Text preview for : Motorola v3x Series Service Manual.pdf part of Motorola v3x Series Motorola v3x Series Service Manual
Back to : Motorola v3x Series Servi | Home
Level 1 and 2 Service Manual
6809497A15-A
V3x
Digital Wireless Telephone
UMTS 2100, GSM 900/1800/1900 GPRS
Level 1 and 2 Service Manual
1 and 2 V3x 6809497A15-A Contents
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Agency Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Computer Program Copyrights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 About This Service Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warranty Service Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Parts Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Controls, Indicators, and Input / Output (I/O) Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Alert Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Battery Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Tools and Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Removing and Replacing the Battery Cover and Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Removing and Replacing the Subscriber Identity Module (SIM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Removing and Replacing the Antenna Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Removing and Replacing the Rear Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Removing and Replacing the Transceiver Board Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Removing and Replacing the Popple Dome PC Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Removing and Replacing the Keypad, Volume/Smart, and Voice Keys . . . . . . . . . . . . . . . . . . . . . . . . 29 Removing and Replacing the Flip Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Removing and Replacing the Flip Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Removing and Replacing the Flip Display Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Subscriber Identity Module (SIM) and Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Personality Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Programming: Software Upgrade and Flexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Exploded View Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Exploded View Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
6809497A15-A
January 31, 2006
3
Contents
V3x
4
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
1 and 2 V3x 6809497A15-A
Introduction
Introduction
Motorola® Inc. maintains a worldwide organization that is dedicated to provide responsive, full-service customer support. Motorola products are serviced by an international network of company-operated product-care centers as well as authorized independent service firms. Available on a contract basis, Motorola Inc. offers comprehensive maintenance and installation programs that allow customers to meet requirements for reliable, continuous communications. To learn more about the wide range of Motorola service programs, contact your local Motorola products representative or the nearest Customer Service Manager.
Product Identification
Motorola products are identified by the model number on a label usually located under the battery. Use the entire model number when inquiring about the product. Numbers are also assigned to chassis and kits. Use these numbers when requesting information or ordering replacement parts.
Product Names
Product names are listed on the front cover. Product names are subject to change without notice. Some product names, as well as some frequency bands, are available only in certain markets.
Product Changes
When electrical, mechanical or production changes are incorporated into Motorola products, a revision letter is assigned to the chassis or kit affected, for example; -A, -B, or -C, and so on. The chassis or kit number, complete with revision number, is imprinted during production. The revision letter is an integral part of the chassis or kit number and is also listed on schematic diagrams and printed-circuit board layouts.
Regulatory Agency Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: · This device may not cause any harmful interference. · This device must accept interference received, including interference that may cause undesired operation. This class B device also complies with all requirements of the Canadian Interference-Causing Equipment Regulations (ICES-003). Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
6809497A15-A
January 31, 2006
5
Introduction
V3x
Computer Program Copyrights
The Motorola products described in this manual may include Motorola computer programs stored in semiconductor memories or other media that are copyrighted with all rights reserved worldwide to Motorola. Laws in the United States and other countries preserve for Motorola, Inc. certain exclusive rights to the copyrighted computer programs, including the exclusive right to copy, reproduce, modify, decompile, disassemble, and reverse-engineer the Motorola computer programs in any manner or form without Motorola's prior written consent. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license or rights under the copyrights, patents, or patent applications of Motorola, except for a nonexclusive license to use the Motorola product and the Motorola computer programs with the Motorola product.
About This Service Manual
Use of this manual assures proper installation, operation, and maintenance of Motorola products and equipment. It contains all service information required for the equipment described and is current as of the printing date. Refer questions about this manual to the nearest Customer Service Manager.
Audience
This manual aids service personnel in testing and repairing V3x GSM telephones. Service personnel should be familiar with electronic assembly, testing, and troubleshooting methods, and with the operation and use of associated test equipment.
Scope
This manual provides basic information relating to V3x telephones, and also provides procedures and processes for repairing the phones at Level 1 and 2 service centers including: · Unit swap out · Repairing of mechanical faults · Basic modular troubleshooting · Testing and verification of unit functionality · Initiate warranty claims and send faulty modules to Level 3 or 4 repair centers
6
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Introduction
Conventions
The following special characters and typefaces, are used in this manual to emphasize certain types of information.
G E
M
Note: Emphasizes additional information pertinent to the subject matter. Caution: Emphasizes information about actions which may result in equipment damage. Warning: Emphasizes information about actions which may result in personal injury.
Keys to be pressed are represented graphically. For example, instead of "Press the Menu Key", you will see "Press M". Information from a screen is shown in text as similar as possible to what displays on the screen. For example, ALERTS or ALERTS. Information that you need to type is printed in boldface type.
Warranty Service Policy
The product is sold with the standard 12-month warranty terms and conditions. Accidental damage, misuse, and extended warranties offered by retailers are not supported under warranty. Non-warranty repairs are available at agreed fixed repair prices.
Out-of-Box Failure Policy
The standard out-of-box failure criteria applies. Return customer units that fail very early on after the date of sale to Manufacturing for root cause analysis, to guard against epidemic criteria. Manufacturing to bear the costs of early life failure.
Product Support
Customer's original units will be repaired but not refurbished as standard. Appointed Motorola Service Hubs will perform warranty and non-warranty field service for level 2 (assemblies) and level 3 (limited PCB component). Motorola High Tech Centers will perform level-4 (full component) repairs.
Customer Support
Customer support is available through dedicated Call Centers and in-country help desks. Product Service training is available through the local Motorola Support Center.
6809497A15-A
January 31, 2006
7
Introduction
V3x
Parts Replacement
When ordering replacement parts or equipment, include the Motorola part number and description used in this service manual. When the Motorola part number of a component is not known, use the product model number or other related major assembly along with a description of the related major assembly and of the component in question. In the U.S.A., to contact Motorola, Inc. on your TTY, call: 800-793-7834.
Accessories and Aftermarket Division (AAD)
Order replacement parts, test equipment, and manuals from AAD.
U.S.A. Phone: 800-422-4210 FAX: 800-622-6210 Outside U.S.A. Phone: 847-538-8023 FAX: 847-576-3023
Website: http://businessonline.motorola.com EMEA Phone: +49 461 803 1404 Website: http://emeaonline.motorola.com Asia Phone: +65 648 62995 Website: http://asiaonline.motorola.com
8
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Introduction
Specifications
Table 1. Specifications
Function Frequency Range EGSM Specification TX: 880 - 915 MHz Frequency (MHz) = 890 + (0.2 × n) where: 0 n 124 Frequency (MHz) = 890 + (0.2 × (n 1024)) where: 955 n 1023 RX: 925 960 MHz Frequency (MHz) = 935 + (0.2 × n) where: 0 n 124 Frequency (MHz) = 935 + (0.2 × (n 1024)) where: 955 n 1023 Frequency Range DCS TX: 1710 to 1785 MHz Frequency (MHz) = 1710.2 + (0.2 × (n 512)) where: 512 n 885 RX: 1805.2 to 1879.8 MHz Frequency (MHz) = 1805.2 + (0.2 × (n 512)) where: 512 n 885 Frequency Range PCS TX: 1850 to 1910 MHz Frequency (MHz) = 1850.2 + (0.2 × (n 512)) where: 512 n 810 RX: 1930 to 1990 MHz Frequency (MHz) = 1930.2 + (0.2 × (n 512)) where: 512 n 810 Frequency Range UMTS TX: 1920 to 1980 MHz Frequency (MHz) = UARFCN1 ÷ 5, where: 9612 < UARFCN1 < 9888 UARFCN1 in increments of 25 RX: 2110 to 2170 MHz Frequency (MHz) = UARFCN1 ÷ 5, where: 10562 < UARFCN1 < 10838 UARFCN1 in increments of 25 Channel Spacing Channels Duplex Spacing Modulation Transmitter Phase Accuracy Frequency Error Input/Output Impedance Nominal Operating Voltage Size Weight Display Battery Life (840mAh)2 200 kHz (GSM, DCS, PCS), 5 MHz UMTS 174 EGSM, 374 DCS, 274 PCS carriers with 8 channels per carrier, 11 UMTS 45 MHz GSM, 95 MHz DCS, 80 MHz PCS, 190 MHz UMTS GMSK AT BT = 0.3 (GSM, DCS, PCS), QPSK (UMTS) 5 degrees RMS, 20 Degrees peak + 0.1ppm 50 ohms (nominal) 3.6 Vdc +10% (battery) +4.4 Vdc +10% (external connector) 89 cc 118 g Main Display: 262K color TFT, 320 x 240, 2.2" CLI Display: 65K color STN, 96x80, 1" GSM: Talk time: Up to 215 minutes GSM: Standby time: Up to 220 to 260 hours WCDMA Talk time: 131 hours WCDMA Standby time: 227 hours WCDMA Video talk time: Up to 90 minutes -10º C to +55º C
Nominal Operating Temperature Range
6809497A15-A
January 31, 2006
9
Introduction
V3x
GSM System Functions Speech Coding Type Bit Rate RF Power Output Spurious Emissions Receive Sensitivity RX Bit Error Rate
Specification Regular Pulse excitation / linear predictive coding with long term prediction (RPE LPC with LTP) 13.0 kbps 32 dBm nominal GSM, 28.5 dBm nominal DCS / PCS -36 dBm from 0.1 to 1 GHz, -30 dBm from 1 to 4 GHz -102 dBm GSM, -102 dBm DCS / PCS < 2%
UMTS System Functions Speech Coding Type RF Power Output Spurious Emissions Error Vector Magnitude PN9 Bit Error Rate (VER) ACLR Adaptive Multirate (AMR) 21 dBm
Specification
-36 dBm from 0.1 to 1 GHz, -30 dBm from 1 to 4 GHz < 17.5% 0.1% @12.2K, -106.7 dBm -33 dBm @+5 MHz, -43 dBm @+10 MHz
10
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Product Overview
Product Overview
Motorola V3x telephones deliver 3G features in a small and lightweight package. These Global System for Mobile communications (GSM) General Packet Radio Service (GPRS) Wireless Application Protocol (WAP)-enabled mobile phones incorporate an icon based User Interface (UI) for easier operation, allows Short Message Service (SMS) text messaging, Multi-media Messaging Services (MMS), and includes Personal Information Manager (PIM) functionality. V3x is a tri-band phones that allow roaming within the GSM 900 MHz, 1800 MHz Digital Cellular System (DCS), and PCS 1900 MHz bands, in addition to the UMTS WCDMA 2100 MHz band. V3x telephones have a clam form factor. They feature an externally viewable 96 x 80 65K color STN CLI display for caller identification with date/time, and an internal 320 x 240 262K TFT color display located in the flip. The bottom part of the clam (front housing) contains the keypad, transceiver printed circuit board (PCB), microphone, flex connection, external accessory connector, smart button, volume buttons, and voice button. The standard 840 mAh Lithium Ion (Li Ion) battery fits behind a removable back cover and provides up to 220 minutes of talk time and 200 hours of standby time in GSM mode. The battery provides up to 131 minutes of talk time, and up to 227 hours of standby time in WCDMA mode. The phone accepts 3V Subscriber Identity Module (SIM) cards that fit into the SIM holder under the battery. The antenna is a fixed stub type antenna. Inexpensive direct connection to a computer or handheld device through USB for data and fax calls, and for synchronizing phonebook entries with Motorola mobile Phone ToolsTM software, can be accomplished using the optional data cable and soft modem.
Features
V3x telephones use advanced, self-contained, sealed, custom integrated circuits to perform the complex functions required for WCDMA communication. Aside from the space and weight advantage, microcircuits enhance basic reliability, simplify maintenance, and provide a wide variety of operational functions. Other features available in this family of telephones include: · WCDMA 2100 MHz, GSM/GPRS 900/1800/1900 MHz · Bluetooth Class 2
Physical
· · · · · Width 53mm Height 99mm Depth 19.8 mm Volume 89 cc Weight 118.0 grams
Audio
· · · · · · · 6809497A15-A AAC AAC+ WAV MP3 AAC+ Enhanced XMF RA v9 January 31, 2006 11
Product Overview
V3x
· MIDI
Video
· MPEG4 Video clip playback
Display
· Main display 320 x 240 pixel 262k TFT · CLI display 96 x 80 65k CSTN
Memory
· · · · 64 MB internal RAM 32 MB internal ROM 64 MB internal ROM user memory Accepts removable TransFlash memory (16, 32 64, 128, 256 or 512MB) modules
Imaging
· Primary camera resolution 2.0 MP · Secondary camera resolution VGA · Dedicated camera key
Wireless Access Protocol (WAP) 2.0 Compliancy
In the WAP environment, access to the Internet is initiated in Wireless Markup Language (WML), which is derived from Hypertext Markup Language (HTML). The request is passed to a WAP gateway, which retrieves the information from the server in standard HTML (subsequently filtered to WML) or directly in WML if available. The information is then passed to the mobile subscriber using the mobile network.
Bitmap image data will download as text. If the image is larger than the screen, only part of the image will display. When the user receives a call while in browser mode, the browser will pause and allow the user to resume after completing the call.
SIM Application ToolkitTM - Class 2
SIM Application Toolkit is a value-added service software product that allows GSM operators to customize the services they offer their customers, from the occasional user who requests sports news and traffic alerts, to a high call time business user who receives stock alerts and checks flight times. Operators can now create their own value-added services menu quickly and easily in the phone. The customized menu will appear as the first menu and may be updated over-the-air with new services when customers request them.
12
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Product Overview
Simplified Text Entry
There are three different ways to enter text using the phone keypad: · iTAP predictive text entry. Press a key to enter a character, and a dynamic dictionary uses this to build and display a set of word or name options. The iTAP feature may not be available on the phone in all languages. · Tap. Press a key to enter a character. · Numeric. The keypad produces numeric characters only. For some text areas, such as phone numbers, this is the only method available.
Caller Line Identification
Upon receipt of a call, the calling party's phone number is compared to the phonebook. If the number matches a phone book entry, that name will be displayed. If there is no phone book entry, the incoming phone number will be displayed. If no caller identification information is available, the Incoming Call message is displayed.
The user must subscribe to a caller line identification service through their service provider.
Other Features
Detailed descriptions of these and the other features can be found in the appropriate user's guide listed in the "Related Publications" section toward the end of this manual.
6809497A15-A
January 31, 2006
13
General Operation
V3x
General Operation
Controls, Indicators, and Input / Output (I/O) Connections
The V3x telephone's controls are located on the sides of the phone and on the keypad. Indicators, in the form of icons, are displayed on the LCD (see Figure 2). V3x phones have an audible alert transducer on the top and I/O connectors, consisting of a headset jack and an accessory port, located on the side and bottom of the phone See Figure 1.
Left Soft Key Make video calls.
Scroll up, down, left, or right. Select. Right Soft Key Camera Key Voice Dial Key Go online. Turn on & off, hang up, exit menus. Clear Key
050592o
Volume Keys Smart Key Make & answer calls. Charge up or go handsfree.
Figure 1. Telephone Controls, indicators, and I/O Connections
Main Display
The main display provides a 262k color backlit display for easy readability in all light conditions. The 320 x 240 display provides room for text, graphics, icons, and prompts.
14
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
General Operation
Display animation makes the phone's menus move smoothly as the user scrolls up and down Turn animation off to conserve the battery. Figure 2 shows common icons displayed on the LCD.
(+49@ ]r ÑyÉ
Date Recent Calls Phonebook Left Soft Key Label
STYLES Service Provider 10/15/03
e s n
M
CAMERA
Messages
à
Browser Clock Right Soft Key Label
031422o
Menu Indicator
Figure 2. Icon Indicators
Alert Settings
Whether a phone displays all indicators depends on the programming and services to which the user subscribes.
V3x telephones include up to 32 preset ring tones and vibrations that can be applied to all alert events at the same time.
Battery Function
Pressing either volume key will mute the alert.
Battery Gauge
The telephone displays a battery level indicator icon in the idle screen to indicate the battery charge level. The gauge shows four levels: 100% (É), 66% (Ç), 33% (Å), and Low Battery (Ä).
Battery Removal
Removing the battery causes the phone to immediately shut down and any pending work (for example, partially entered phone book entries or outgoing messages) is lost.
To ensure proper memory retention, turn OFF the phone before removing the battery.
6809497A15-A
January 31, 2006
15
General Operation
V3x
G
Operation
If the battery is removed while receiving a message, the message will be lost.
For detailed operating instructions, refer to the appropriate user's guide listed in "Related Publications" on page 45.
16
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
1 and 2 V3x 6809497A15-A
Tools and Test Equipment
Tools and Test Equipment
Table 1 lists tools and test equipment recommended for disassembly and reassembly of V3x telephones. Use either the listed items or equivalents. Table 1. General Test Equipment and Tools
Motorola Part Number1 RSX4043-A -- See Table 7 Torque Driver Torque Driver Bit T-3, T-5, T-6 Plus, Apex 440-6IP Torx Plus or equivalent Rapid Charger Antistatic Mat Kit (includes 66-80387A95 antistatic mat, 66-80334B36 ground cord, and 42-80385A59 wrist band) Disassembly tool, plastic with flat and pointed ends (manual opening tool) Tweezers, Plastic Digital Multimeter, HP34401A2 GSM / DCS Test SIM Description Application Used to remove and replace screws. Used with torque driver. Used to charge battery and to power phone. Provides protection from damage to device caused by electrostatic discharge (ESD). Used during assembly/disassembly of phone. Used during assembly/disassembly of phone. Used to measure battery voltage. Used to enable manual test mode.
0180386A82
0-00-00-30005 -- -- 8102430Z04
1. To order in North America, contact Motorola Aftermarket and Accessories Division (AAD) at (800) 422-4210 or FAX (800) 622-6210; Internationally, AAD can be reached by calling (847) 538-8023 or faxing (847) 576-3023. 2. Not available from Motorola. To order, contact Hewlett Packard at (800) 452-4844.
6809497A15-A
January 31, 2006
17
Disassembly
V3x
Disassembly
This section provides instructions for the disassembly of V3x telephones. Tools and equipment used for the phone are listed in Table 1, preceding.
G G E
Many of the integrated devices used in these phones are vulnerable to damage from ESD. Ensure adequate static protection is in place when handling, shipping, and servicing the internal components of this phone. Avoid stressing the plastic in any way to avoid damage to either the plastic or internal components.
Removing and Replacing the Battery Cover and Battery
All batteries can cause property damage and/or bodily injury, such as burns, if a conductive material, such as jewelry, keys, or beaded chains, touches exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become very hot. Use care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects. 1. 2. Ensure the phone is turned off. Press down on the battery latch and then slide the battery cover as shown in Figure 1.
Battery Cover latch
Battery Cover
051209o
Figure 1. Removing the Battery Cover 3. Lift the battery cover away from the phone.
18
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
4.
Lift the bottom end of the battery first and then lift the battery out the phone. (see Figure 2).
Battery
1 2
051210o
Figure 2. Removing the Battery
E
There is a danger of explosion if the Lithium Ion battery is replaced incorrectly. Replace only with the same type of battery or equivalent as recommended by the battery manufacturer. Dispose of used batteries according to the manufacturer's instructions. 5. 6. 7. To replace, align the battery with the battery compartment so the contacts on the battery match the battery contacts in the phone. Insert the battery, top end first, into the battery compartment and push down. Insert the bottom edge of the battery housing into the base of the phone, then slide the battery cover over the battery and snap it into place.
6809497A15-A
January 31, 2006
19
Disassembly
V3x
Removing and Replacing the Subscriber Identity Module (SIM)
1. 2. Remove the battery door and battery as described in the procedures. Carefully slide the SIM out of the SIM holder.
SIM
SIM holder
060078o
Figure 3. Removing the SIM 3. 4. To replace, slide the SIM into the holder, ensuring the notched corner of the SIM aligns with the notch molded into the holder. Replace the battery and battery cover as described in the procedures.
20
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
Removing and Replacing the Antenna Cover
1. 2. Remove the battery cover, battery and SIM, as described in the procedures. Insert the disassembly tool under each side of the antenna cover to release the antenna cover latches (see Figure 4).
Disassembly tool Latch
Antenna cover
051212o
Figure 4. Removing the Antenna Cap 3. 4. 5. 6. 7. 8. Carefully lift the antenna cover away from the phone. To replace, align the antenna cover over the antenna. Place the curved edge of the antenna cover onto the phone. Carefully press the straight edge of the antenna cover into place until the latches snap into place. Insert the RF grommet fully into the opening on the antenna cover. Reassemble the SIM, battery, and battery cover as described in the procedures.
6809497A15-A
January 31, 2006
21
Disassembly
V3x
Removing and Replacing the Rear Housing
G
This product contains static-sensitive devices. Use anti-static handling procedures to prevent electrostatic discharge (ESD) and component damage.
1. 2.
Remove the battery cover, battery, SIM, and antenna as described in the procedures. Using a Torx driver with a T-6 bit, remove the 6 screws along the sides of the phone (see Figure 5).
Housing screw
Housing screws
Housing screw
Figure 5. Removing the Rear Housing Screws
Housing screws
051217o
22
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
3.
Carefully lift the rear housing away from the phone.
Disassembly tool
Figure 6. Removing the Rear Housing 4. 5. 6.
Rear housing frame
051218o
Lower the rear housing onto the phone. Ensure the screw holes are aligned to the transceiver PCB assembly. Insert the 6 housing screws and tighten to a torque setting of 1.5 inch pounds or 16 N/cm (Newton/centimeters). Do not over tighten. Replace the SIM, battery, and battery cover as described in the procedures.
6809497A15-A
January 31, 2006
23
Disassembly
V3x
Removing and Replacing the Transceiver Board Assembly
G G
This product contains static-sensitive devices. Use anti-static handling procedures to prevent ESD and component damage.
1.
Remove the battery cover, battery, SIM, antenna, and rear housing as described in the procedures..
The flexible printed cable (FPC) (flex) is easily damaged. Exercise extreme care when handling. 2. Carefully work the flat end of the disassembly tool under the flex connector and unseat the connector from its socket the transceiver board (see Figure 7).
Disassembly tool
Transceiver PCB Assembly
Flex connector
051219o
Figure 7. Disconnecting the Flex From the Transceiver Board
24
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
3.
Lift the transceiver board assembly and the keypad switchdome assembly out of the front housing (see Figure 8).
Transceiver PC board
051222o
Figure 8. Removing the Transceiver Board Assembly 4. Use the T6 driver to remove the screw in the middle of the transceiver PC board assembly (see Figure 9). Set the screw aside for re-use.
Transceiver PC board screw
051233o
Figure 9. Removing Transceiver PC Board Screw
6809497A15-A
January 31, 2006
25
Disassembly
V3x
Removing and Replacing the Antenna
1. 2. Remove the battery cover and battery, SIM, rear housing, and transceiver board assembly as described in the procedures. Unlatch the latches that secure the acoustic assembly to the transceiver PC board.
Acoustic chamber latch
Acoustic chamber latch
051693o
Figure 10. Removing the Antenna Assembly 3. Lift the acoustic chamber assembly away from the transceiver PC board.
26
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
4.
Use the disassembly tool to pry the antenna out of the antenna assembly.
Disassembly tool
Acoustic chamber
Antenna
051694o
Figure 11. Removing the Antenna 5. 6. 7. To replace, insert the antenna into the acoustic chamber assembly. Align the acoustic chamber assembly to the transceiver PC board and gently press into position. Ensure the latches are secured to the PC board. Replace the transceiver PC board assembly, rear housing, SIM, battery and battery cover as described in the procedures.
6809497A15-A
January 31, 2006
27
Disassembly
V3x
Removing and Replacing the Popple Dome PC Board
1. 2. Remove the battery cover and battery, SIM, rear housing, transceiver board assembly and antenna as described in the procedures. Turn the Transceiver PC board assembly over and use the disassembly tool to unseat the popple dome board flex connector (see Figure 12).
Popple dome board
Transceiver PC board
Popple dome flex connector Disassembly tool
051235a
Figure 12. Removing the Popple dome FLEX Connector 3. 4. 5. 6. 7. 8. 9. Separate the popple dome board from the transceiver PC board assembly. To replace, insert the popple dome flex connector squarely into its mating connector on the transceiver board and press firmly until it snaps into place. Turn the popple dome board over onto the transceiver PC board. Insert and tighten the transceiver PC board screw with the T6 driver to a torque setting of 13 N/cm. Do not overtighten. Carefully place the transceiver board and the switchdome assembly into the front housing. Insert the display flex connector squarely into its mating connector on the transceiver board and press firmly until it snaps into place. Replace the rear housing, antenna, SIM, battery, and battery cover as described in the procedures.
28
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
Removing and Replacing the Keypad, Volume/Smart, and Voice Keys
1. 2. Remove battery cover, battery, SIM, antenna, rear housing, and transceiver board assembly as described in the procedures. Use the plastic tweezers to lift the volume/smart keys out of their slot in the front housing (see Figure 14).
Plastic tweezers
Volume/Smart Keys
051223o
Figure 13. Removing the Keypad, Volume/Smart, and Voice Buttons
6809497A15-A
January 31, 2006
29
Disassembly
V3x
3.
Use the plastic tweezers to lift the keypad assembly away from the front housing (see Figure 14).
Plastic tweezers
Keypad
051225o
Figure 14. Removing the Keypad 4. 5. To replace, insert the keypad into the front housing, ensuring the keys align properly with the openings in the front housing. Carefully set the keypad volume/smart buttons and voice button assembly onto the metal switchdome assembly. Ensure the volume/smart key make contact with the switchdome assembly on the transceiver board when installed. Replace the transceiver board assembly, display flex connector, rear housing assembly, antenna, SIM, battery, and battery cover as described in the procedures.
6.
30
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
Removing and Replacing the Flip Assembly
1. 2. Remove the battery cover, battery, SIM, antenna, rear housing, transceiver board assembly, and keypad assembly as described in the procedures. Carefully flex the base inner front housing downward to release the hinge assembly from the front housing (see Figure 15).
Front Housing
Hinge Assembly
051226o
Figure 15. Removing the Flip Assembly 3. Carefully slide the display flex cable and connector through the housing assembly. Avoid damage to the flex cable.
G
The flexible printed cable (FPC) (flex) is easily damaged. Exercise extreme care when handling.
4. 5. 6. 7.
Lift the housing assembly away from the flip assembly. Be careful not to damage the display flex cable. To replace, carefully thread the display flex connector through the slot on the keypad housing assembly. Avoid damaging the flex cable. Flex the front housing slightly and insert the hinge assembly into the front housing. Avoid damaging the flex cable and connector. Replace the keypad assembly, transceiver board assembly, rear housing, antenna, SIM, battery, and battery cover as described in the procedures. January 31, 2006 31
6809497A15-A
Disassembly
V3x
Removing and Replacing the Flip Cover
1. Remove the battery cover, battery, SIM, antenna, rear housing, transceiver board assembly, keypad assembly and flip assembly as described in the procedures. Use the metal tweezers to remove the 2 flip screw covers at the top of the flip assembly (see Figure 16).
2.
Flip screw covers
051246o
Figure 16. Removing the Flip Cover Screws 3. Use a T5 bit to remove 2 flip screws at the top of the flip assembly located under the screw covers. Set the screws aside for reuse unless they are damaged.
32
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
4.
Insert the tip of a thin bladed knife under the display lens starting under the Motorola logo and pry it upward.
Knife Flip Assembly Display lens
051244o
Figure 17. Removing the Display Lens 5. 6. Slide the pointed edge under the edge of the display lens to separate it from the flip assembly and remove it from the flip assembly. Use the T-5 driver to remove the 2 flip assembly screws at the bottom of the flip assembly. Set the screws aside for re-use unless they are damaged.
Flip Assembly Flip screw Flip screw
052145o
Figure 18. Removing the Bottom Flip Screws
6809497A15-A
January 31, 2006
33
Disassembly
V3x
7.
Use the disassembly tool to remove the camera lens (see Figure 19).
disassembly tool
camera lens
060076o
Figure 19. Removing the Camera Lens 8. Use a T3 driver to remove the camera lens screw (see Figure 20).
Camera lens screw
o
Figure 20. Removing the Camera Lens Screw
34
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
9.
Insert the disassembly tool between the flip assembly and the flip housing to release the 3 latches on each side of the flip assembly (see Figure 17).
Flip Housing Catch
Flip Housing Catch
Flip Assembly
Flip Housing Catch
040958o
Figure 21. Removing the Display Lens 10. Carefully lift the flip cover away from the flip assembly. Avoid damaging the display flex cable and connector. 11. To replace, align the flip cover with the flip assembly. Press the flip cover onto the flip assembly until the 6 latches are fully engaged. 12. Insert and tighten the 4 flip screws with the T5 driver to a final torque setting of 0.6 in.-lbs. Do not overtighten. 13. Remove the adhesive from the back of the new display lens and apply lens to the flip housing. 14. Replace the flip assembly, keypad assembly, transceiver board assembly, rear housing, antenna, SIM, battery, and battery cover as described in the procedures.
6809497A15-A
January 31, 2006
35
Disassembly
V3x
Removing and Replacing the Flip Display Assembly
1. Remove the battery cover, battery, SIM, antenna, rear housing, transceiver board assembly, keypad assembly, flip assembly, and flip cover as described in the procedures.
G
The flexible printed cable (FPC) (flex) is easily damaged. Exercise extreme care when handling. 2. Use the disassembly tool to unseat the flip assembly flex connector from the display assembly (see Figure 22).
Disassembly tool
Flip Assembly flex connector
Display Assembly
051247o
Figure 22. Removing the Flip Assembly Flex Connector 3. Move the flex connector away from the display assembly.
36
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
4.
Use the disassembly tool to unseat the camera assembly flex connector from the display module assembly (see Figure 23).
Disassembly tool Camera assembly flex connector
040962o
Figure 23. Removing the Camera Assembly Flex Connector
G
The FPC (flex) is easily damaged. Exercise extreme care when handling.
6809497A15-A
January 31, 2006
37
Disassembly
V3x
5.
Use the pointed end of the disassembly tool to lift zero insertion force (ZIF) latch that unlocks the ZIF connector socket (see Figure 24).
Speaker Flex ZIF Socket
Display Assembly
040963o
Figure 24. Removing the Display Assembly Flex Connector 6. 7. Carefully disconnect the flex connector from the ZIF socket. Carefully lift the display assembly out of the flip assembly (see Figure 25).
040964o
Figure 25. Removing the Display Assembly
38
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Disassembly
8.
To replace, align the display assembly to the flip housing.
G
The FPC (flex) is easily damaged. Exercise extreme care when handling.
9. Lower the display assembly onto the flip housing. 10. Insert the speaker flex ZIF connector into the ZIF socket. Lock the ZIF connector with the pointed end of the disassembly tool. 11. Carefully press the camera connector into its socket on the display assembly. 12. Carefully seat the display flex connector to the socket on the flip assembly. 13. Carefully align the flip flex assembly connector and seat it in it's socket on the the display assembly. 14. Carefully lower the display assembly onto the flip assembly. Be careful not to damage the display flex or flex connector while reassembling the display lens assembly. 15. Replace the flip assembly cover, flip assembly, keypad assembly, transceiver board, rear housing, antenna, SIM, battery, and battery cover as described in the procedures.
6809497A15-A
January 31, 2006
39
Subscriber Identity Module (SIM) and Identification
V3x
Subscriber Identity Module (SIM) and Identification
SIM Card
A SIM is required to access the existing local GSM network, or remote networks when traveling (if a roaming agreement has been made with the provider). The SIM contains: · All the data necessary to access GSM services · The ability to store user information such as phone numbers · All information required by the network provider to provide access to the network
Personality Transfer
A personality transfer is required when a phone is express exchanged or when the main board is replaced. Personality transfers reproduce the customer's personalized details such as menu, and stored memory, such as phonebooks, or program the customer's phone with basic user information such as language selection. V3x telephones use mobile PhoneTools® synchronization software to effect a personality transfer.
Identification
Each Motorola GSM phone is labeled with a several identifying numbers. The following section describes the current identifying labels.
Mechanical Serial Number (MSN)
The Mechanical Serial Number (MSN) is an individual unit identity number and remains with the unit throughout its life. The MSN can be used to log and track a phone on Motorola's Service Center Database. The MSN is divided into 4 sections as shown in Figure 26.
MSN 10 Digits 3 Digits APC 1 Digit DC 2 Digits DC 4 Digits SNR
Account Product Code TM e.g., StarTAC Phone130
Distribution Center e.g., Easter Inch
Date Code: Year and Month of Shipment
Phone's individual serial number
000807b
Figure 26. MSN Label Breakdown
40
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Subscriber Identity Module (SIM) and Identification
International Mobile Station Equipment Identity (IMEI)
The International Mobile station Equipment Identity (IMEI) number is an individual number unique to the PCB and stored within the phone's memory. The IMEI uniquely identifies an individual mobile station provides a way to control access to GSM networks based on mobile station types or individual phones. The full IMEI structure is listed in Table 2. Table 2. IMEI Number Breakdown
TAC NNXXXXXX Serial Number ZZZZZZ Check Digit A
Where: TAC NN ZZZZZZ A Type Allocation Code, formerly known as Type Approval Code Reporting body identifier Individual unit serial number Phase 1 = 0. Phase 2 = check digit defined as a function of all other IMEI digits
XXXXXX Type identifier
Other label number configurations present are: · TRANSCEIVER NUMBER: Identifies the product type, usually the SWF number. (for example, V100). · PACKAGE NUMBER: Identifies the equipment type, mode, and language in which the product is shipped.
6809497A15-A
January 31, 2006
41
Troubleshooting
V3x
Troubleshooting
Table 3. Level 1 and 2 Troubleshooting Chart
SYMPTOM 1. Telephone will not turn on or stay on. PROBABLE CAUSE a) Battery either discharged or defective. VERIFICATION AND REMEDY Measure battery voltage across a 50 ohm (>1 Watt) load. If the battery voltage is <3.25 Vdc, recharge the battery using the appropriate battery charger. If the battery will not recharge, replace the battery. If battery is not at fault, proceed to b. Visually inspect the battery connectors on both the battery and the telephone. Realign and, if necessary, either replace the battery or refer to a Level 3 Service Center for battery connector replacement. If battery connectors are not at fault, proceed to c. Remove the transceiver board assembly. Substitute a known good assembly and temporarily reassemble. Press and hold the PWR button; if the phone turns on and stays on, disconnect the dc power source and reassemble with the new transceiver board assembly. Verify that the fault has been cleared. If the fault has not been cleared then proceed to d. Replace the keyboard assembly. Temporarily connect a +3.6 Vdc supply to the battery connectors. Press and hold the PWR button. If the phone turns on and stays on, disconnect the dc power source and reassemble with the new keyboard assembly. Check to make sure that the antenna pin is properly connected to the transceiver board assembly. If connected properly, substitute a known good antenna. If the fault is still present, proceed to b. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble the unit with the new transceiver board assembly. Remove rear chassis assembly from the phone, check general condition of FPC (flex). If the flex is good, check that the flex connector is fully pressed down. If not, check connector to transceiver board connections. If faulty connector, replace the transceiver board assembly. If connector is not at fault, proceed to b. Temporarily replace the flip assembly with a known good assembly. If fault has been cleared, reassemble with the new flip assembly. If fault not cleared, proceed to c. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble the unit with the new transceiver board assembly. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly.
b) Battery connectors open or misaligned.
c) Transceiver board assembly defective.
d) keyboard assembly failure.
2. Telephone exhibits poor reception or erratic operation such as calls frequently dropping or weak or distorted audio.
a) Antenna assembly defective.
b) Transceiver board assembly defective.
3. Display is erratic, or provides partial or no display.
a) Transceiver board connections faulty.
b) Flip assembly defective.
c) Transceiver board assembly defective.
4. Incoming call alert transducer audio distorted or volume is too low.
Faulty transceiver board assembly.
42
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Troubleshooting
Table 3. Level 1 and 2 Troubleshooting Chart (Continued)
SYMPTOM 5. Telephone transmit audio is weak (usually indicated by called parties complaining of difficulty in hearing voice). PROBABLE CAUSE VERIFICATION AND REMEDY a) Microphone connections to the Gain access to the microphone as described in transceiver board assembly defective. the procedures. Check connections. If connector is faulty proceed to c; if the connector is not at fault, proceed to b. b) Microphone defective. Gain access to microphone. Disconnect and substitute a known good microphone. Place a call and verify improvement in transmit signal as heard by called party. If good, reassemble with new microphone. If microphone is not at fault, reinstall original microphone and proceed to c. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly.
c) Transceiver board assembly defective.
6. Receive audio from earpiece speaker is a) Connections to or from transceiver Gain access to the transceiver board assembly weak or distorted. board assembly defective. as described in the procedures. Check flex and the flex connector from the flip assembly to the transceiver board assembly. If flex is at fault, replace flip assembly. If flex connector is at fault, proceed to d. If connection is not at fault, proceed to b. b) Flip assembly defective. Temporarily replace the flip assembly with a known good assembly. If fault has been cleared, reassemble with the new flip assembly. If fault not cleared, proceed to c. Check that the antenna is installed correctly. If the antenna is installed correctly, substitute a known good antenna assembly. If this does not clear the fault, reinstall the original antenna assembly and proceed to d. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly. Check the SIM contacts for dirt. Clean if necessary and check if fault has been cleared. If the contacts are clean, insert a known good SIM into the telephone. Power up the phone and confirm that the SIM has been accepted. If the fault no longer exists, replace the defective SIM. If the SIM is not at fault, proceed to b. Temporarily replace the flip assembly with a known good assembly. If fault has been cleared, reassemble with the new flip assembly. If fault not cleared, proceed to c. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly. Temporarily replace the flip assembly with a known good assembly. If fault has been cleared, reassemble with the new flip assembly. If fault not cleared, proceed to b. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly.
c) Antenna assembly defective.
d) Transceiver board assembly defective.
7. Telephone will not recognize or accept SIM.
a) SIM defective.
b) Flip assembly defective.
c) Transceiver board assembly defective.
8. Phone does not sense when flip is opened or closed (usually indicated by inability to answer incoming calls by opening the flip, or inability to make outgoing calls).
a) Flip assembly defective.
b) Transceiver board assembly defective.
6809497A15-A
January 31, 2006
43
Troubleshooting
V3x
Table 3. Level 1 and 2 Troubleshooting Chart (Continued)
SYMPTOM 9. Vibrator feature not functioning. PROBABLE CAUSE VERIFICATION AND REMEDY Transceiver board assembly defective. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly. Faulty charger circuit on transceiver board assembly. Test a selection of batteries in the rear pocket of the desktop charger. Check LED display for the charging indications. If the batteries charge properly, then the internal charger is at fault. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly.
10. Internal Charger not working.
11. Real Time Clock resetting when standard battery is removed.
Lithium button cell in the display board Refer service to a Level 3 service center for may be depleted. replacement.
12. No or weak audio when using headset. a) Headset plug not fully pushed into Ensure the headset plug is fully seated in the the jack socket. jack socket. If fault not cleared, proceed to b. b) Faulty jack socket on transceiver board assembly. Replace the transceiver board assembly (refer to 1c). Verify that the fault has been cleared and reassemble with the new transceiver board assembly.
Programming: Software Upgrade and Flexing
Contact your local technical support engineer for information about equipment and procedures for flashing and flexing.
44
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Part Numbers
Part Numbers
The following charts are provided as a reference for the parts associated with V3x telephones.
Related Publications
Motorola V3x User's Guide, English 68XXXXX108
6809497A15-A
January 31, 2006
45
Part Numbers
V3x
Exploded View Diagram
3 1 2 5
4 10
8 12 11 15 20 21 22 23 26 25 28 29 9 13
7
14 16
17 18
27
30 31 32
33 34 35 36 37
040967o
Figure 27. Exploded View Diagram
46
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
Part Numbers
Exploded View Parts List
Table 4. Exploded View Parts List
Item Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Part Number 6171885B01 4885102C24 6188777Y01 0171425C01 3371139D01 1171902B01 0171102C01 0171456C01 5571967B01 3871407C01 0171347C01 3271688B01 5988515L01 0171325C01 0188755Y01 1371698B01 0387726M02 3271689B02 3271689B01 3371697B02 Description LENS, 2MP FLASH, CAMERA LENS, CLI HOUSING, FLIP OUTER ESCUTCHEON, FLIP GASKET, CLI MODULE, DISPLAY FLEX, HINGE CAM, HINGE ADJUST, MACRO MODULE, 2MP GASKET, 2MP MAGNET SPEAKER, EARPIECE ASSY HOUSING, FLIP INNER MESH, ACOUSTIC SCREW, FLIP (4X) BUMPER, FLIP (left) Bumper, flip (right) ESCUTCHEON, EARPIECE Item Number 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Part Number 0171343C01 3271688B02 6171865B01 6188778Y01 0387726M02 0188747Y01 3971966B01 3888722Y01 3871943B01 3871942B01 0171646C01 0171107C01 SLG4932AA 0188746Y01 0387791L07 SNN5781A 1571931B01 1571951B01 Description MODULE, VGA GASKET, VGA LENS, VGA LENS, MAIN DISPLAY SCREW, FLIP HOUSING, BASE INNER ASSY CONTACT, KNUCKLE KEYPAD, MAIN BUTTONS, SIDE, UP / DN / SMART BUTTONS, SIDE, CAM / VA FLEX, POPPLE DOME / EL SHIELD, SPACER ASSY PCB, TRANSCEIVER, ASSY HOUSING, BASE OUTER ASSY SCREW, BASE (6X) BATTERY, MAIN, SC5 COVER, BATTERY SC5 HOUSING, LOWER ANTENNA CAP
E
There is a danger of explosion if the Lithium Ion battery pack is replaced incorrectly. Replace only with the same type of battery or equivalent as recommended by the battery manufacturer. Dispose of used batteries according to the manufacturer's instructions. To order parts use the following Link: https://wissc.motorola.com/wissc_root/main/BrowserOK.html (Password is Required) For information on ordering parts contact EMEA at +49 461 803 1404.
6809497A15-A
January 31, 2006
47
Part Numbers
V3x
48
January 31, 2006
6809497A15-A
Level 1 and 2 Service Manual
1 and 2 Index V3x 6809497A15-A
Index
A
alert settings 15 antenna cap, removing and replacing 21 antenna, removing and replacing 26
IMEI 41 indicators service indicator (status light) 14 Introduction 5
B
battery function 15 gauge 15 removing 18 battery cover removing 18
L
liquid crystal display (LCD) 14
M
MSN 40
N C
caller ID 13 Canadian Interference-Causing Equipment regulations 5 changes product 5 conventions 7 copyrights computer software 6 names product 5
O
operation controls, indicators, and I/O 14 operation, general 14 overview, product 11
D
disassembly 18 display 14
P
parts 45 exploded view diagram 46 exploded view parts list 47 product changes 5 identification 5 names 5 publications, related 45
E
exploded view diagram 46 exploded view parts list 47
F
FCC rules 5 features caller ID 13 SIM Toolkit 12 text entry 13 Wireless Access Protocol (WAP) 12 features, product 11 flip assembly, removing and replacing 31 flip cover, removing and replacing 32 flip display assembly, removing and replacing 36
R
rear housing removing 22 regulatory agency compliance 5 related publications 45 removing antenna 26 antenna cap 21 battery 15, 18 battery cover 18 flip assembly 31 flip cover 32 flip display assembly 36 rear housing 22 SIM 20 transceiver board assembly 24
I
identification 40 international mobile station equipment identity 41 mechanical serial number 40 product 5
6809497A15-A
January 31, 2006
Index-1
Index
V3x
volume/smart buttons 29 replacement parts contact information 8 replacing antenna 26 antenna cap 21 battery 18 flip assembly 31 flip cover 32 flip display assembly 36 rear housing 22 SIM 20 transceiver board assembly 24 volume/smart buttons 29
W
warranty service 7 wireless access protocol (WAP) 12
S
serial number mechanical 40 service manual about 6 revisions 7 scope 6 service policy 7 customer support 7 out of box failure 7 product support 7 service procedure ordering replacement parts 8 shut down upon battery removal 15 SIM Application Toolkit 12 SIM card 40 personality transfer 40 replacing 20 SIM, removing and replacing 20 specifications 9 support customer 7 product 7
T
text entry 13 tools and test equipment 17 transceiver board assembly, removing and replacing 24 troubleshooting 42
V
volume/smart buttons, removing and replacing 29
Index-2
January 31, 2006
6809497A15-A
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners.® Reg. U.S. Pat. & Tm. Off.
© 2005 Motorola, Inc.
All rights reserved. Mobile Devices Business, Sawgrass International Concourse 789 International Parkway, Mailstop S2C Sunrise, FL 33325-6222