Text preview for : SONY HCD-RV600 PAGES 1 TO 27.pdf part of SONY HCD-RV600 SONY HCD-RV600 PAGES 1 TO 27
Back to : SONY HCD-RV600 PAGES 1 TO | Home
HCD-RV600D/RV600DJ
SERVICE MANUAL
Ver 1.5 2004. 10
E Model
· HCD-RV600D/RV600DJ is the tuner, deck, DVD and amplifier section in MHC-RV600D/RV600DJ.
Photo : HCD-RV600D
This system incorporates Dolby* Digital, Pro Logic Surround, DTS**, and the DTS Digital Surround System. * Manufactured under license from Dolby Laboratories. "Dolby", "Pro Logic", and the double-D symbol are trademarks of Dolby Laboratories. ** Manufactured under license from Digital Theater Systems, Inc. "DTS" and "DTS Digital Surround" are registered trademarks of Digital Theater Systems, Inc.
Amplifier section
Model Name Using Similar Mechanism DVD Section Tape deck Section DVD Mechanism Type Base Unit Name Model Name Using Similar Mechanism Tape Transport Mechanism Type
NEW CDM58D-DVBU17 DVBU17 NEW CWM43RR-01
SPECIFICATIONS
COMPONENT VIDEO OUT: Y: 1 Vp-p, 75 ohms The following measured at AC 120, 127, 220, 240 V, PB, PR: 0.7 Vp-p, 75 ohms 50/60 Hz DIN power output (rated) 100 + 100 watts (6 ohms PHONES (stereo mini jack): accepts headphones of at 1 kHz, DIN) 8 ohms or more Continuous RMS power output (reference) accepts impedance of 6 to 100 + 100 watts (6 ohms Front speaker: 16 ohms at 1 kHz, 10% THD) SUB WOOFER OUT voltage 1 V, impedance 1 kilohm Inputs MD/VIDEO (AUDIO) IN (phono jacks): voltage 450/250 mV, impedance 47 kilohms GAME (AUDIO) IN (phono jack): voltage 250 mV, impedance 47 kilohms MIC (phone jack) (except for North American and European models): sensitivity 1 mV, impedance 10 kilohms Video color system format NTSC, PAL CD OPTICAL DIGITAL OUT (Square optical connector jack, rear panel) Wavelength 660 nm Output Level 18 dBm
Tape deck section
Recording system Frequency response 4-track 2-channel stereo 40 13,000 Hz (±3 dB), using Sony TYPE I cassette
Disc player section
System Laser Compact disc and digital audio and video system Semiconductor laser (DVD: =650 nm, CD: =780 nm) Emission duration: continuous 780 790 nm DVD (PCM 48 kHz): 2 Hz 22 kHz (±1 dB) CD: 2 Hz 20 kHz (±1 dB)
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Wavelength Outputs Frequency response MD/VIDEO (AUDIO OUT) (phono jacks): voltage 250 mV, impedance 1 kilohm VIDEO OUT (phono jack): max. output level 1 Vp-p, unbalanced, Sync negative, load impedance 75 ohms S-VIDEO OUT (4-pin/mini-DIN jack): Y: 1 Vp-p, unbalanced, Sync negative, C: 0.286 Vp-p, load impedance 75 ohms
Tuning range Antenna Antenna terminals Intermediate frequency
87.5 108.0 MHz FM lead antenna 75 ohm unbalanced 10.7 MHz
-- Continued on next page --
MINI HI-FI COMPONENT SYSTEM
9-874-120-06
2004J16-1 © 2004.10
Sony Corporation
Audio Group Published by Sony Engineering Corporation
HCD-RV600D/RV600DJ
Ver 1.5
AM tuner section
Tuning range Pan-American models:
Self-diagnosis function
530 1,710 kHz (with the interval set at 10 kHz) 531 1,710 kHz (with the interval set at 9 kHz) 531 1,602 kHz (with the interval set at 9 kHz) 531 1,602 kHz (with the interval set at 9 kHz) 530 1,710 kHz (with the interval set at 10 kHz) AM loop antenna External antenna terminal 450 kHz
(When letters/numbers appear in the display)
When the self-diagnosis function is activated to prevent the system from malfunctioning, a fivecharacter service number (e.g., C 13 00) with a combination of a letter and digits appears on the screen. In this case, check the following table.
C:13:00
Philippine models: Other models:
Antenna Antenna terminals Intermediate frequency
General
Power requirements Mexican model: Saudi Arabian model: 120 V AC, 60 Hz 120 127 V, 220 V or 230 240 V AC, 50/60 Hz Adjustable with voltage selector 220 V AC, 50/60 Hz 120 V, 220 V or 230 240 V AC, 50/60 Hz Adjustable with voltage selector 230 watts 0.4 watts (in Power Saving Mode) Approx. 280 × 325 × 368 mm Approx. 10.6 kg
First three characters of the service number
Cause and/or corrective action
Thai model: Other models:
C 13
The disc is dirty. , Clean the disc with a soft cloth (see page 70). The disc is not inserted correctly. , Re-insert the disc correctly.
C 31
Power consumption
Dimensions (w/h/d) Mass
E XX To prevent a malfunction, the (XX is a number) system has performed the selfdiagnosis function. , Contact your nearest Sony dealer or local authorized Sony service facility and give the 5-character service number. Example: E 61 10
Design and specifications are subject to change without notice.
MODEL IDENTIFICATION
-- BACK PANEL --
NOTES ON MB BOARD EXCHANGE
If a MB board is exchanged, "DRIVE AUTO ADJUSTMENT" may be unable to be performed. In this case, initialize a memory in the following procedure. 1. Starting Test Mode (see page 2 (SUPPLEMENT-1)). 2. Press the 2 button of remote commander to set the Drive Manual Operation (see page 4 (SUPPLEMENT-1)). 3. Press the 6 button of remote commander to set the Memory Check (see page 6 (SUPPLEMENT-1)). 4. Press the [CLEAR] button of remote commander to initialize a memory. MODEL 600D : MY, SP model 600D : E3 600D : EA3 600D : TH 600D : E51 600D : MX 600DJ : EA3
· Abbreviation E3 : 240V AC Area in E model E51 : Chilean and Peruvian model EA3 : Saudi Arabia model MX : Mexican model MY : Malaysia model SP : Singapore model TH : Thai model
Parts No.
PARTS No. 4-240-159-0s 4-240-159-1s 4-240-159-2s 4-240-159-4s 4-240-159-5s 4-240-159-6s 4-240-159-7s
2
HCD-RV600D/RV600DJ
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
TABLE OF CONTENTS 1. GENERAL ·········································································· 4 2. DISASSEMBLY ································································ 6
Case (Top) ····································································· 7 Lid (DVD) ····································································· 7 Front Panel Section ······················································· 8 DVD Mechanism Deck (CDM58D-DVBU17) ············· 8 Tape Mechanical Deck (CWM43RR-01) ····················· 9 PANEL Board, SUB PANEL Board, REMOTE Board ························································· 10 2-7. Cassette Holder ··························································· 11 2-8. SUB TRANSFORMER Board, Back Panel, DC Fan (M961) ······································· 11 2-9. TRANSFORMER Board, MAIN Board ····················· 12 2-10. FRONT AMP Board, SURROUND Board, REG Board ·································································· 12 2-11. VIDEO Board, MB Board ·········································· 13 2-12. RF Board, DRIVER Board ········································· 13 2-13. Optical Pick-up ··························································· 14 2-14. MOTOR Board, DIODE Board, SENSOR Board ······ 14 2-1. 2-2. 2-3. 2-4. 2-5. 2-6.
3. TEST MODE ···································································· 15 4. MECHANICAL ADJUSTMENTS ····························· 18 5. ELECTRICAL ADJUSTMENTS ······························· 19 6. DIAGRAMS ······································································ 21
6-1. Block Diagrams DVD DSP Section ···················· 21 DVD SYS Section ···················· 22 Tuner Section ···························· 23 Main Section ····························· 24 6-2. Circuit Boards Location ·············································· 25 6-3. Printed Wiring Board RF Board ··························· 26 6-4. Schematic Diagram RF Board ······························ 27 6-5. Printed Wiring Board MB Board (Side A) ··········· 28 6-6. Printed Wiring Board MB Board (Side B) ··········· 29 6-7. Schematic Diagram MB Board (1/6) ···················· 30 6-8. Schematic Diagram MB Board (2/6) ···················· 31 6-9. Schematic Diagram MB Board (3/6) ···················· 32 6-10. Schematic Diagram MB Board (4/6) ···················· 33 6-11. Schematic Diagram MB Board (5/6) ···················· 34 6-12. Schematic Diagram MB Board (6/6) ···················· 35 6-13. Printed Wiring Board TC Board ··························· 36 6-14. Schematic Diagram TC Board ······························ 37 6-15. Printed Wiring Board Main Section ····················· 38 6-16. Schematic Diagram Main Section (1/3) ··············· 39 6-17. Schematic Diagram Main Section (2/3) ··············· 40 6-18. Schematic Diagram Main Section (3/3) ··············· 41 6-19. Printed Wiring Board VIDEO Board ···················· 42 6-20. Schematic Diagram VIDEO Board ······················· 43 6-21. Printed Wiring Board FRONT AMP Board ·········· 44 6-22. Schematic Diagram FRONT AMP Board ············ 45 6-23. Printed Wiring Board Panel Section ····················· 46 6-24. Schematic Diagram Panel Section (1/2) ··············· 47 6-25. Schematic Diagram Panel Section (2/2) ··············· 48 6-26. Schematic Diagram Sensor Section ······················ 49 6-27. Printed Wiring Board Sensor Section ··················· 49 6-28. Printed Wiring Board TRANSFORMER Board ··· 50 6-29. Schematic Diagram TRANSFORMER Board ····· 51 6-30. Printed Wiring Board SUB TRANSFORMER Board ····························· 52 6-31. Schematic Diagram SUB TRANSFORMER Board ····························· 53 6-32. IC Pin Function Descriptions ······································ 54
This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing · Keep the temperature of soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
7. EXPLODED VIEWS ······················································ 65
7-1. 7-2. 7-3. 7-4. Main Section ······························································· 65 Front Panel Section ····················································· 66 Chassis Section ··························································· 67 DVD Mechanism Deck Section (CDM58D-DVBU17) ················································· 68
8. ELECTRICAL PARTS LIST ······································· 69
3
HCD-RV600D/RV600DJ
Ver 1.1 2002.11
Note for Service: [DISC TRAY LOCK] The disc tray lock function for the antitheft of a demonstration disc in the store is equipped. Setting Procedure : 1. Press the ?/1 button to turn the set on. 2. Press two buttons of x and Z simultaneously for five seconds. 3. The message "LOCKED" is displayed and the tray is locked. Releasing Procedure : 1. Press two buttons of x and Z simultaneously for five seconds. 2. The message "UNLOCKED" is displayed and the tray is unlocked. Note : When "LOCKED" is displayed, the tray lock is not released by turning power on/off with the POWER button.
SECTION 1 GENERAL
This section is extracted from instruction manual.
Main unit
ALPHABETICAL ORDER BUTTON DESCRIPTIONS
AJ
ALBUM+/ ws (19, 20, 26) AUDIO jacks wl (61) CD SYNC ql (48, 50) Deck A wg (47) Deck B qk (47, 48, 49, 50, 58) DIRECTION 8 (47, 48, 50, 58) DISC 1 3 qs (18, 19, 20) DISC SKIP/EX-CHANGE qd (17, 19, 22) Disc tray qa (17) DISPLAY 8 (45, 53, 54, 55) DVD eg (18, 20, 26, 27, 36, 48, 49) DVD DISPLAY q; (18, 23, 24, 34, 36, 37, 38, 41, 55) DVD MENU 8 (26) DVD TOP MENU 8 (26) ECHO LEVEL control*1 wk (58) EFFECT ON/OFF 4 (51, 52) ENTER qf (16, 18, 20, 23, 24, 26, 27, 34, 36, 37, 38, 43, 46, 49, 50, 52, 55, 57, 59) FM MODE 8 (45) GAME ea (56, 61) GAME EQ wd (51) GAME MIXING wf (56) GROOVE 3 (51)
KZ
KARAOKE PON*1 2 (57) MD (VIDEO)*2 es (62) MIC jack*3 wj (57) MIC LEVEL control*3 wk (57) MOVIE EQ 9 (51) MUSIC EQ 6 (51) P FILE wa (52) PHONES jack qh PLAY MODE 8 (18, 20, 49) PTY*4 8 (46) REC PAUSE/START w; (48, 50, 58) REPEAT 8 (23) SURROUND*5 5 (53) TAPE A/B ed (47, 48, 58) TUNER MEMORY 8 (43) TUNER/BAND ef (43, 44) VIDEO jack e; (61) VIDEO (MD)*6 es (62) VOLUME control qg (33, 53, 59)
?/1 (power) 1 v/V/b/B 7 Z OPEN/CLOSE qd Z PUSH (deck B) qj m/M + ws hH ws ./> ws X ws x ws Z PUSH (deck A) wh *1 MHC-RV900D (except for Latin American model) and RV600D/RV600DJ (except for Latin American model) only *2 except for MHC-GX90D *3 MHC-RV900D and RV600D/ RV600DJ only *4 European model only *5 MHC-RV600D/RV600DJ only *6 MHC-GX90D only
12 34567
8
90
qa
eg ef ed es ea e; wl wk wj wh wg wf wd ws waw; ql
qs qd qf qg
qh qj qk
4
HCD-RV600D/RV600DJ
Remote control
ALPHABETICAL ORDER
NZ
NEXT eh (18, 27) Number buttons qs (19, 27, 39, 40, 42, 49) P FILE ws (52) PLAY MODE r; (18, 20, 21, 49) PRESET +/ eh (43, 44) PREV eh (18, 27) REPEAT el (23) RETURN O ej (27, 39, 41) / qk (19) SCAN/SLOW SLEEP 1 (59) SUBTITLE ql (38) SURROUND es (53) TAPE rd (47, 48) TUNER/BAND ra (43, 44) TUNING +/ eg (43, 45) TV ?/1 4 (15) TV CH +/ rf (15) TV/VIDEO 7 (15) TV VOL +/ 6 (15) VOL +/ wf (33, 53, 59)
Inserting two R6 (size AA) batteries into the remote
AM
ALBUM +/ wd wl (19, 20, 26) AMP MENU wa (57) ANGLE w; (37) AUDIO ed (35) CLEAR qf (20, 22, 24, 25, 31) CLOCK/TIMER SELECT 2 (51, 60) CLOCK/TIMER SET 3 (16, 50, 59) DISC +/ wg wj (19, 20, 22) DISPLAY qa (45, 53, 54, 55) DVD rs (18, 20, 21, 26, 27, 28, 36, 48, 49) DVD DISPLAY qd (18, 23, 24, 34, 36, 37, 38, 41, 55) DVD MENU ef (26) DVD SETUP ek (28, 33, 40) DVD TOP MENU ef (26) EFFECT ON/OFF es (51, 52) ENTER wk (16, 18, 20, 21, 23, 24, 26, 27, 28, 33, 34, 36, 37, 38, 40, 43, 46, 49, 50, 52, 55, 57, 59) GAME 8 (56, 61) GAME EQ e; (51) GAME MIXING 0 (56) GROOVE es (51) MD (VIDEO) 9 (62) MOVIE EQ e; (51) MULTI ROOM* ea MUSIC EQ e; (51)
e E E e
Tip
With normal use, the batteries should last for about six months. When the remote no longer operates the system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage.
BUTTON DESCRIPTIONS
?/1 (power) 5 x qg nN qh X qj M/m/ eh * This button does not function.
Setting the clock
1 Press ?/1 to turn on the system. 2 Press CLOCK/TIMER SET on the
remote.
3 Press M or m on the remote repeatedly
to set the hour.
4 Press , on the remote.
12 345
The minute indication flashes.
5 Press M or m on the remote repeatedly
to set the minute.
6 Press ENTER.
rf rd rs ra r; el ek ej eh eg ef ed es ea e; wl wk wj 6 7 8 9 0 qa qs qd qf qg qh qj qk ql w; wa ws wd wf wg wh
The clock starts working.
To adjust the clock
1 Press CLOCK/TIMER SET on the remote. 2 Press M or m on the remote repeatedly to
select "CLOCK SET", then press ENTER.
3 Do the same procedures as step 3 to 6
above.
Note
The clock settings are canceled when you disconnect the power cord or if a power failure occurs.
5
HCD-RV600D/RV600DJ SECTION 2 DISASSEMBLY
· The equipment can be removed using the following procedure.
SET
CASE (TOP)
DVD LID
FRONT PANEL SECTION
TAPE MECHANISM DECK (CWM43RR-01)
DVD MECHANISM DECK BLOCK
PANEL BOARD, SUB PANEL BOARD, REMOTE BOARD, MICROPHONE BOARD
SUB TRANSFORMER BOARD, BACK PANEL, DC FAN (M961)
VIDEO BOARD, MB BOARD
CASSETTE HOLDER
TRANSFORMER BOARD, MAIN BOARD
RF BOARD, DRIVER BOARD
FRONT AMP BOARD, REG BOARD
OPTICAL PICK-UP
MOTOR BOARD, DIODE BOARD, TRAY, SENSOR BOARD
Note : Follow the disassembly procedure in the numerical order given.
6
HCD-RV600D/RV600DJ
Note: Follow the disassembly procedure in the numerical order given. 4 case 2-1. Case (Top)
3 seven screws (BVTP 3 × 8)
2 three screws (case 3 TP2)
1 three screws (case 3 TP2)
2-2. Lid (DVD)
DVD mechanism deck (CDM58D-DVBU17) 1 Turn the pulley to the direction of arrow.
4 lid (DVD)
pulley
3
2 Pull-out the disc tray.
7
HCD-RV600D/RV600DJ
2-3. Front Panel Section
8 front panel section 4 screw (BVTP 3 × 8) 1 connector (CN502)
3 screw (BVTP 3 × 8)
chassis section
7 connector (CN603) 6 connector (CN602)
2 flat type wire (CN605)
5 three screws (BVTP 3 × 8)
2-4. DVD Mechanism Deck (CDM58D-DVBU17)
4 connector (CN103) 5 connector (CN505)
0 DVD mechanism deck (CDM58D)
6 connector (CN508) 7 three screws (BVTP 3 × 8)
9 four screws (BVTP 3 × 8)
2 flat type wire (CN104) 8 two screws (BVTP 3 × 8)
1 connector (CN103)
3 connector (CN709)
chassis section
8
HCD-RV600D/RV600DJ
2-5. Tape Mechanical Deck (CWM43RR-01)
panel section
1 six screws (BVTP 2.6 × 8)
2 tape mechanism deck (CWM43RR-01)
9
HCD-RV600D/RV600DJ
2-6. PANEL Board, SUB PANEL Board, REMOTE Board
2 One or two mic knobs
1 volume knob
front panel
0 two claws
9 two claws
qh four screws (BVTP 2.6 × 8)
qd REMOTE board qs connector (CN1006) 7 five screws (BVTP 2.6 × 8) 6 Remove the three solderings.
3 connector (CN1202) qk SUB PANEL board
qj two screws (BVTP 2.6 × 8) qg connector (CN1002)
qa PANEL board 4 two screws (BVTP 2.6 × 8)
5 MICROPHONE board qf connector (CN1003) 8 six screws (BVTP 2.6 × 8)
10
HCD-RV600D/RV600DJ
2-7. Cassette Holder
3 cassette door, spring (B) 4 cassette, holder (L)
2
1 6
8 cassette, holder (R)
5
7 cassette door, spring (A)
panel section
2-8. SUB TRANSFORMER Board, Back Panel, DC Fan (M961)
qf back panel 0 three screws (BVTP 3 × 8)
7 two screws (BVTP 3 × 8)
1 connector (CN901)
2 connector (CN902) qs two screws (BVTP 3 × 8) 5 five screws (BVTP 3 × 8) 6 screw (BVTT 3 × 6) 8 screw (BVTP 3 × 8) 9 four screws (BVTT 3 × 6) qd dc fun (M961)
qa SUB TRANSFORMER board
3 connector (CN903)
4 connector (CN704)
chassis section
11
HCD-RV600D/RV600DJ
2-9. TRANSFORMER Board, MAIN Board
8 two screws (BVTT 3 × 6) 4 two screws (BV 4 × 8) 5 TRANSFORMER board 3 two screws (BV 4 × 8) qh FRONT AMP board ASSY qf TC board qs connector (CN609) qd connector (CN608) 9 two screws (BVTP 3 × 8) 0 cover (heat sink)
7 three screws (BVTT 3 × 6)
qa two claws 2 connector (CN915) 1 connector (CN914)
qg MAIN board
6 two screws (BVTP 3 × 8)
2-10. FRONT AMP Board, SURROUND Board, REG Board
heat sink assy
2 bracket (PWB)
qa lead pin board 4 bracket (PWB) 0 five screws (BVTP 3 × 8)
1 two screws (BVTP 3 × 8)
3 two screws (BVTP 3 × 8)
6 REG board 5 screw (BVTP 3 × 8) 8 two screws (BVTP 3 × 16) 9 FRONT AMP board 7 five screws (BVTP 3 × 8)
12
HCD-RV600D/RV600DJ
Ver 1.1 2002.11
2-11. VIDEO Board, MB Board
3 two screws (BVTP 3 × 8) 1 flat type wire (CN501,CN202)
2 flat type wire (CN503,CN302)
7 two screws (BVTP 3 × 8) 8 bracket (AL) 0 two screws (BVTP 3 × 8) qa
5 VIDEO board 9 screw (BVTT 3 × 6) qd screw (BVTP 3 × 8)
qs heat sink (DVD) qf screw (BVTP 3 × 8)
4 PWB holder qg MB board
6 flat type wire (CN501)
2-12. RF Board, DRIVER Board
2 cushion (A)
7 cushion (DVD)
1 screw (BVTP 3 × 8)
3
8 bracket (DVD)
qa two screws (PTP 2.6 × 12) qs RF board 6 cushion (DVD)
5 connector
0 9
4 flat type wire
qd screw (BVTP 2.6 × 8)
qf DRIVER board
13
HCD-RV600D/RV600DJ
2-13. Optical Pick-up
2 3 step screw (L) 4 step screw (L) 7 insulator 6 insulator 9 optical pick-up 5 step screw (L) 8 insulator
1 floating screw (PTPWH M2.6)
0 holder (DBU1) assy
2-14. MOTOR Board, DIODE Board, SENSOR Board
qs tray (DVD) qa screw (PTPWH 2.6 × 8) 6 MOTOR board 5 connector (CN723) 1 two screws (BVTP 2.6 × 8)
3 flat type wire (CN721) 2 Remove the two solderings of motor. 4 connector (CN722) qf SENSOR board 9 screw (BVTP 2.6 × 8) 8 DIODE board
qd screw (BVTP 2.6 × 8) 7 screw (BVTP 2.6 × 8)
0 bracket (sensor)
14
HCD-RV600D/RV600DJ SECTION 3 TEST MODE
[Cold Reset] · The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. Press three buttons x , ENTER , and ?/1 simultaneously. 2. The fluorescent indicator tube display "COLD RESET" and the set is reset. [Hot Reset] 1. Press three buttons x , GAME EQ , and DISPLAY simultaneously. 2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset [Tuner Step Change] (Except for European and Middle Eastern models) · A step of AM channels can be changed over between 9 kHz and 10 kHz. Procedure: 1. Press `/1 button to turn the set ON. 2. Select the function "TUNER", and press TUNER/BAND button to select the BAND "AM". 3. Press `/1 button to turn the set OFF. 4. Press ENTER and `/1 buttons simultaneously, and the display of fluorescent indicator tube changes to "AM 9 k STEP" or "AM 10 k STEP", and thus the channel step is changed over. [VIDEO/MD Function Change] · Change of function VIDEO or MD ( also the input level changes). Procedure: 1. Press `/1 button to turn the set ON. 2. Press VIDEO (MD) and `/1 buttons simultaneously, and the display of fluorescent indicator tube changes to "MD" or "VIDEO", and thus the channel step is changed over. 3. Press `/1 button to turn the set OFF. [DISC TRAY LOCK] The disc tray lock function for the antitheft of a demonstration disc in the store is equipped. Setting Procedure : 1. Press the ?/1 button to turn the set on. 2. Press two buttons of x and Z simultaneously for five seconds. 3. The message "LOCKED" is displayed and the tray is locked. Releasing Procedure : 1. Press two buttons of x and Z simultaneously for five seconds. 2. The message "UNLOCKED" is displayed and the tray is unlocked. Note : When "LOCKED" is displayed, the tray lock is not released by turning power on/off with the POWER button.
Ver 1.1 2002.11
[GC Test Mode] · This mode is used to check the FL tube, LED, keyboard, volume and phones. Procedure: 1. Press three buttons x , GAME EQ , and DISC 2 simultaneously. 2. LEDs and fluorescent indicator tube are all turned on. 3. Press simultaneously the two buttons of GAME EQ and DISC 2 . Whenever these two buttons are pressed simultaneously, the mode changes from Key check, Key count check, Headphones input check and Volume check in this order. 4. When the Key check mode is entered, the display shows the indication of "KEY 0 0 0". The keys that are assigned to the respective channels of the key entry signal lines (KEY0, KEY1, KEY2) that are input to IC001 Display Controller on the panel board, are checked. While you press the button, the number that corresponds to the key shown in the table below, is displayed in the location of the corresponding channel. (The ?/1 and DISPLAY buttons are not included in these channels.) Display 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Left (KEY0) DVD TUNER/BAND TAPE A/B VIDEO (MD) GAME -- DVD MENU GAME EQ MUSIC EQ EFFECT ON/OFF GAME MIXING GROOVE -- -- Center (KEY1) X x ALBUM + > M+ gG m ALBUM . b V B v -- Right (KEY2) DISC 1 DISC 2 DISC 3 Z OPEN/CLOSE DISC SKIP/ EX-CHANGE TUNER MEMORY PLAY MODE FM MODE REPEAT DIRECTION DVD TOP MENU CD SYNC REC PAUSE/START P FILE ENTER MOVIE EQ DVD DISPLAY
5. When the Key count check mode is entered, the display shows the indication of "KEY 0 1". Whenever the button is pressed, number in the first digit increments. (RV90D: 38) At the same time, only when the key is being pressed, the KEY channel is displayed in the second digit. (KEY0: 1, KEY1: 2, KEY2: 3) (The buttons that are already pressed once and the buttons of ?/1 and DISPLAY are not counted.) 6. When the Headphones input check mode is entered, the display shows the indication of "H_P OFF" or "H_P ON" depending on the PHONES jack status. 7. When the Volume check mode is entered, the display shows the indication of "VOLUME FLAT" or "VOLUME DOWN" or "VOLUME UP" depending on the VOLUME status. 8. You can exit the Test Mode when you press the GAME EQ and DISC 2 buttons simultaneously.
15
HCD-RV600D/RV600DJ
[MC Test Mode] · This mode is used to check operations of the respective sections of Amplifier, Tuner, and Tape. Procedure: · To enter MC Test Mode 1. Press `/1 button to turn on the set. 2. Press the three buttons of x , GAME EQ and DISC 3 simultaneously.
* Check of Amplifier Initial settings: Input , GAME EQ , FLAT Mode , MUSIC VA CS , OFF Output channel switching: MUSIC key: L ,L R , R through MOVIE key: L , SL R , SR through GAME key:L , L, SL, C R , R, SR, SW through TOOL MODE key: L , C R , SW through 1. When VOLUME control knob is turned clockwise even slightly, the sound volume increases to is maximum and a message "VOLUME MAX" appears for two seconds, then the display returns to the original display. 2. When VOLUME control knob is tuned counter-clockwise even slightly, the sound volume decreases to its minimum and a message "VOLUME MIN" appears for two seconds, then the display returns to the original display. 3. When you press the v button, the message "GEQ MAX" is displayed and the entire band of the graphic equalizer is set to the maximum level. 4. When you press the V button, the message "GEQ MIN" is displayed and the entire band of the graphic equalizer is set to the minimum level. 5. When you press the b , B or P FILE button, the message "GEQ FLT" is displayed and the entire band of the graphic equalizer is set to the center level. 6. Whenever you press the ENTER button, it toggles between "VACS ON" and "VAC OFF" so that you can switch ON or OFF of VACS. * To return to normal mode again. 1. When you want to exit this mode, press `/1 button. 2. The cold reset is enforced at the same time.
[Aging Mode] This mode can for operation check of tape deck section. · If an error occurred: The aging operation stops and display then status. · If no error occurs: The aging operation continues repeatedly. Procedure: 1. Press the DVD button to select the function "DVD". 2. Load the tapes into the decks A and B respectively. 3. Set a disk in "DISK1" tray. 4. Press the PLAY MODE button to set the "ALL DISCS" mode, and press the REPEAT button to "REPEAT" off. 5. Press three buttons of x , GAME EQ , and DISC SKIP/EXCHANGE simultaneously. 6. The florescent indicator tube display "AGING", aging mode start. 7. To exit from the aging mode, operate the cold reset. · The sequence during the aging mode is following as below. · If an error occurred, stop display that step. Aging mode sequence (Tape deck section):
Rewind the tape A "TAPE A AG-1" Shut off Rewind the tape B "TAPE A AG-2" Shut off FWD play the tape A "TAPE A AG-3" 2 minutes Fast forward the tape A "TAPE A AG-4" Shut off or 20 seconds RVS play the tape A "TAPE A AG-5" 2 minutes Rewind the tape A "TAPE A AG-6" Shut off FWD play the tape B "TAPE B AG-3" 2 minutes Fast forward the tape B "TAPE B AG-4" Shut off or 20 seconds RVS play the tape B "TAPE B AG-5" 2 minutes Rewind the tape B "TAPE B AG-6" Shut off
16
HCD-RV600D/RV600DJ
Ver 1.3 2003.10
[DVD Service Mode] · The sequence during the aging mode is following as below. Aging mode sequence (DVD section): Tray Turn
Disc 1 Chucking
[DVD and CD Ship Mode (No Memory Clear)] · This mode moves the position to the position durable to vibration Use this mode when returning the set to the customer after repair. Procedure: 1. Press `/1 button to turn the set ON. 2. Press three DVD button and `/1 button simultaneously. 3. After the "STANBY" display blinks six times, a message "LOCK" is displayed on the fluorescent indicator rube, and the DVD ship mode is set. [DVD and CD Ship Mode (Memory Clear)] · This mode moves the pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair. Procedure: 1. Press `/1 button to turn the set ON. 2. Press three buttons ENTER , DISC 1 , and DVD button simultaneously. 3. After the "STANDBY" display blinks six times, a message "LOCK" is displayed on the fluorescent indicator tube, and the DVD ship mode is set.
TOC Read
Track 1 Play 2 seconds Last Track Play 2 seconds
17
HCD-RV600D/RV600DJ SECTION 4 MECHANICAL ADJUSTMENTS
[REPEAT 5 LIMIT OFF MODE] · This mode is used to enable infinite repetitions. Normally, the number of repetitions allowed is 5. Procedure: 1. Press `/1 button to turn ON the power supply. 2. Set the function "DVD". 3. Press three burtons x , MUSIC EQ and DISC 2 is simultaneously. 4. Infinite repetitions is enabled. 5. This state is maintained ( memorized ) until COLD RESET is executed. Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement
Mode Torque meter Meter reading
FWD
CQ-102C
FWD back tension REV
CQ-102C
CQ-102RC
REV back tension FF/REW
CQ-102RC
CQ-201B
FWD tension
CQ-403A
REV tension
CQ-403R
3.06 N · m to 6.96 N · m 31 to 71 g · cm (0.43 0.98 oz · inch) 0.19 N · m to 0.58 N · m 2 to 6 g · cm (0.02 0.08 oz · inch) 3.06 N · m to 6.96 N · m 31 to 71 g · cm (0.43 0.98 oz · inch) 0.19 N · m to 0.58 N · m 2 to 6 g · cm (0.02 0.08 oz · inch) 6.96 N · m to 14.02 N · m 71 to 143 g · cm (0.98 1.99 oz · inch) 9.80 N · m 100 g or more (3.53 oz or more) 9.80 N · m 100 g or more (3.53 oz or more)
18
HCD-RV600D/RV600DJ SECTION 5 ELECTRICAL ADJUSTMENTS
DECK SECTION
0 dB=0.775 V 2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjust. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and RCH. 7. Switches and controls should be set as follows unless otherwise specified. · Test Tape Tape P-4-A100 WS-48B P-4-L300 Signal 10 kHz, 10 dB 3 kHz, 0 dB 315 Hz, 0 dB Used for Azimuth Adjustment Tape Speed Adjustment Level Adjustment
L-CH peak Output level
within 1dB within 1dB
Screw position
R-CH peak L-CH peak R-CH peak
Screw position
3. Mode: Playback
test tape P-4-A100 (10 kHz, 10 dB) L-CH MAIN board CN607 set R-CH pin 7 waveform of oscilloscope
oscilloscope pin 5 pin 6 L R V H
Record/Playback Head Azimuth Adjustment
DECK A
DECK B
Note: Perform this adjustments for both decks
Procedure: 1. Mode: Playback
test tape P-4-A100 (10 kHz, 10 dB) main board CN607 Pin 5 (L-CH) Pin 7 (R-CH) level meter set main board CN607 Pin 6 (GND) +
in phase 45 ° good
90 ° 135 ° 180 ° wrong
4. After the adjustments, apply suitable locking compound to the pats adjusted. Adjustment Location: Playback Head (Deck A). Record/Playback/Erase Head (Deck B).
reverse forward
19
HCD-RV600D/RV600DJ
Ver 1.5
TUNER SECTION
FM Tuned Level Adjustment
FM RF SSG 75 coaxial
DVD SECTION
AUTO SERVO ADJUSTMENT After parts related to the servo circuit (RF amplifier (IC001), DSP (IC509), motor driver (IC501), EEPROM (IC203) so on) are replaced, re-adjusting the servo circuit is necessary. Select "ALL" at "1. DRIVE AUTO ADJUSTMENT" (Refer to page 3 (SUPPLEMENT-1) in TEST MODE) and adjust DVD-SL (single layer), CD and DVD-DL (dual layer).
set
Carrier frequency : 98 MHz Modulation : AUDIO 1 kHz, 75 kHz deviation (100%) Output level : 25 dB (at 75 open)
FM ANTENNA terminal (TM1)
RFMON Level Check Perform a RFMON level check before exchanging optical pick-up. Measurement Point: MB board CN501 17 pin (RFMON) -- 1 pin (AGND)
RFMON signal waveform
Procedure: 1. Supply a 25 dB 98 MHz signal from the ANTENNA terminal. 2. Tune the set to 98 MHz. 3. Adjust RV11 to the point (moment) when the TUNED indicator will change from going off to going on. Adjustment Location: MAIN board Null Adjustment
FM RF SSG 75 coaxial
VOLT/DIV: 200 mV TIME/DIV: 500 ns
RFMON level
· Standard value
set Carrier frequency : 98 MHz Modulation : AUDIO 1 kHz, 75 kHz deviation (100%) Output level : 60 dB (at 75 open) FM ANTENNA terminal (TM1)
Test Disc DVD CD TDV-520CSO (J-2501-236-A) LUV-P01 (4-999-032-01)
RFMON level Standard Value 1.09 ± 0.2 Vp-p 1.05 ± 0.2 Vp-p
Procedure: 1. Supply a 60 dB 98 MHz signal from the ANTENNA terminal. 2. Tune the set to 98 MHz. 3. Measure voltage between pin 22 and pin 3 of IC 11. Adjust T11 ubtil the voltage becomes 0 V. Adjustment Location: MAIN board
Adjustment Location [MAIN BOARD] Component side
IC1104
T11 NULL
1
TM1
12 13
IC11
24
RV11 FM TUNED LEVEL
20
HCD-RV600D/RV600DJ SECTION 6 DIAGRAMS
6-1. Block Diagrams DVD DSP Section
OPTICAL PICK-UP BLOCK (KHM-240AAA) IC001 DVD/CD RF AMP IC509 CD DECODER SERVO DSP 50 RFAC DOUT 64 IC701 DVD DECODER 44,41,39,35 32,30,27,24,26 XSAK 46 XDCK 48 XSRQ 53 IC202 SDRAM 2,4,5,7, 8,10,11,13, 74,76,77,79, 80,82,83,85, DQ0-DQ31 31,33,34,36, 37,39,40,42, 45,47,48,50, 51,53,54,56 25-27 A0-A9,A10/AP,NC 60-66 24,21 MDQM0-MDQM3 16,71,28,59 WE 17 CAS 18 RAS 19 CS 20 BS0 22 BS1 23 IC706 SDRAM FFDR FRDR TFDR TRDR 5 6 IC503 AMP 33 FFDR 34 FRDR 31 TFDR 32 TRDR XTAI 71 7 29 SFDR 30 SRDR 66-69,71, 73-75, 16 MD0-MD15 96,97,99, 101,102, 104-106 79,80, MA0-MA9 82-87, 89,91 XMWR 76 XRAS 78 XOE 94 XCAS 95 10 2-10, I/O0-I/O15 41-49 ALE HCS0 WEH.UDS HEL.LDS 190 195 25 27 8 IC206 DVD SYSTEM PROCESSOR DOUT LRCK PCMD BCK
Ver 1.2 2003.10
RF
1 DVDRFP 3 4 5 6 12 11 10 9 16 15 14 13 17 18 20 Q001 LD DRIVE Q002 LD DRIVE A2 B2 C2 D2 A B C D CD A CD B CD C CD D CD F CD E VC
RFAC 57
117 RFIN
HDB0-HDB8
177-174 SDDATA0-SDDATA7, 171-168,182 SDERROR 179 SDEN 183 SDCLK 178 SDREQ
IEC958 156
IEC958 MAIN SECTION (Page 24)
A B C D E F VC
MIRR 27 FE 40 TE 39 MNTR 42
MIRR
PI/CE
20 39 40 41 43
MIRR FE SE TE RFDC
LRCK PCMD BCK SBSO EXCK WFCK C2PO SCOR WDCK
65 66 67 79 80 10 14 15 17
163 160 158 148 147 151 155 150 146
LRCK MDAT BCLK SBIN EXCK WFCK C2PO SCOR GSCOR
A
GPIO4(1) BCK LRCK XCK CDSEL MREQ ML MC MDI 150 149 148 147 109 110 115 114 113 DATA0 BCK-ZIBA LRCK-ZIBA XCK CDSEL MREQ ML MC MDI 768FS V C Y CB/R CR/B WIDE
32
57-60 64-71 75-78 MD0-MD31 81-84 88-95 99-102 42-33 45,46
12 4
DVDLD
21 DVD LD
MA0-MA11
CDLD LD GND PD VCC GND +5V
22 CD LD 23 DVDPD 24 CDPD
SDEN SDATA SCLK LDON
48 47 46 26
SDEN DATA RF CLK RF LDON MDP 25
IC703(1/2) AMP 137 MDIN2
HAD0-15
62,73,86,97 MDQM0-MDQM3 53 MWE 52 MCAS 51 MRAS 49 MCS0 48 BA0 47 BA1
VDAC 0 VDAC 1 VDAC 2 VDAC 3 VDAC 4 VS
131 128 125 122 119 107
B
MAIN SECTION (Page 24)
IC215 ADDRESS LATCH 55,54,52,51, 49-47,45-40,38-36 34,33,31 LE 29 56 HA1-3 IC205 RAM 2,3,5,6,8-10 HA4-22 12-17,19-21, 23,24,26
IC501 MOTOR/COIL DRIVE FCS+ FCSTRK+ TRK36 DO1+ 37 DO134 DO2+ 35 DO2IN1+ 48 IN1- 1 IN2+ 3 IN2- 4
HAD0-HAD15
22,19-14, 11-3
HA1-HA3 2,207,206
HA1-3
21-24, 27-32 17 18 33 34 35
A0-A9 188 DRVRDY
SPDL+ SPINDLE M MOTOR SPDL-
27 DO5+ 28 DO547 IN6+ 46 IN6-
IN5- 13 OUT5 14
SPIN
135 SPO 107 APE0
XTL1 171 MNT1 92 GFS 109
IC203 EEPROM WC DO DI SK CS R/B 8 6 5 4 3 1 IC906 CLOCK GENERATOR Q201 3 27M 10 33M 13 33M SYS-RESET XTI 7 XTI 8 X902 27MHz
XRD XWR XCS XINT0 XINT1
OUT6 45
D0-D7 A0-A7 172-176 5,7, 17 18 19 20 21 164 1,2,4 9-14 8 8
SLED MOTOR
M
SLA+ SLASLB+ SLB-
32 31 30 29
DO3+ DO3DO4+ DO4-
IN3- 7 IN4- 10
TSDM MUTE5 MUTE34 MUTE12
XRST
IC904 FF 3 Q CLR 6 IC902 GATE 4 2 1 CK 1 Q903 Q904 I2C-CL I2C-DA
22 21 20 19 IC703(2/2) AMP INLIM
158 157 187 186 185 184 116 191 161 160 202
26 76 77 63 2 3 4 5 6 7 8 13 19 22 24
WE RAS OE UCAS LCAS
WC EEPROM CS EEPROM DRVRX DRVTX DRVCLK HIRQ1 HIRQ2 RST SPC I2C DA I2C CL RESET
XIN 139
SSTP SQSO SQCK MD2 XRST MUTE DATA XLAT CLOK SENS SCLK GFS COUT FOK LOCK
HA1-8, HA10-19 A0-A7, 1-7,10,13, HA21,22 26 CE A9-A18, 16-25,48 11 WE A20,A21 29-36, HAD0-15 28 OE DQ0-DQ15 38-45
C
DVD SYS SECTION (Page 22)
SW Q901
XRST
IC901 MECHANISM CONTROLLER 58 6 32 33 34 35 36 37 38 78 79 D+3.3V 3
IC907
76 73 63
60
44 43 62 28 82 83 2 8 7 66 65 67 29 61
31 52 54 3 98 59 49 27 50 9 72 71 30 74 75
26 64
45
14-21 89-96 85 84 12 22 23 25
SLED B SLED A FG LDON SDCLK RF SDATA RF SDEN FCS JMP 2 FCS JMP 1 RI TE FE MIRR SLED
MUTE 2D
XRD XWR XCS DVD INIT0 DVD INIT1 DVD
FCOMP L
GFS DVD MNT1
LDSEL TSDM SPON
SCOR JIT
INLIM SQSO SQCK DOCTRL/ISBTEST XDRST MUTE CD DATA CD LAT CD CLOK CD SENS CD SCLK CD GFS CD COUT CD FOK CD LOCK CD
SCK DSD
CS ZIVA SI ZIVA SO ZIVA SCK ZIVA DRVIRQ DRVRDY RST I2C SIO I2C SCL
D0-D7 A0-A7
REG
1
D+5V
IC210 1 REG 3 +1.8V
40 XTAL X901 20MHz 41 EXTAL IC903 EEPROM SDA EEP 5 SCL EEP 100 WP EEP 99 5 SDA 6 SCL 7 WP · Signal Path : DVD : DIGITAL OUT
21
21
HCD-RV600D/RV600DJ
DVD SYS Section
IC1001 DISPLAY CONTROL S1002-1014 FUNCTION KEY S1022-1034 FUNCTION KEY S1042-1055 FUNCTION KEY S1081 ENCODER VOLUME 13 VOL1A 14 VOL1B ENTER GAME-MIXING GAME-LED MD/VIDEO 21 KEY1 TAPE TUNER CD/DVD 20 KEY2 DECODE-LED 22 KEY0 26 27 28 29 30 31 32 16 Q1004-1008 Q1010-1012 D1001-1005 D1007-1009
IC1104(3/3) MASTER CONTROL
S1062 DISPLAY S1061 POWER 73 DISPLAY KEY 74 POWER KEY POWER 3 Q1009 LED DRIVER D1006 POWER
LED DRIVER
IC921 DVD+12V CD/DVD POWER 34 IC922 M+9V 3 REG 1 +VH -VH D371 IC923 IC1003 REMOTE CONTROL RECIEVER 4 SIRCS IC934 GC+5V DVD DSP SECTION (Page 21) I2C-CL I2C-DA SYS-RESET 29 IIC-CLK 30 IIC-DATA 41 SYS-RESET IC932 S-OUT 9 S-IN 8 IC1002 12 11 8 6 5 2 4 3 1 13 100 S-IN 1 S-OUT IC704 S-CLK 7 9 2 S-CLK D+5V (DVD) SYS-POWER 40 IC706 Q715-716 1 SWITCH REG 3 REG 1 Q723-725 SWITCH Q901 RELAY DRIVE AC4 VF F913 RY901 AC IN D+4V 3 REG 1 UNREG+12V F912 S901 3 REG 1 UNREG+20V D732 A+12V 3 REG 1 +VL -VL IR F918 F917 F916 2 REG 4 D271 F914 F915 1 T911 POWER TRANSFORMER
3 X1 X1101 5MHz 4 X2
C
Q971 VP REG
D911
AC3
D733
F919
F911
10
RESET 6
42 M-RESET
MAIN SECTION (Page 24)
+5V
3
F
HP
17 HEADPHONE SEG1-33 33-58 61-67 G1-13 68-80 Q1001-1003 GRID DRIVER
Q714 FL1001 10 XC-IN FLUORESCENT INDICATOR TUBE X800 32.768kHz 11 XC-OUT 13 X-OUT X801 16MHz 15 X-IN STB-RELAY 40 RESET 12 ACCUT 18 Q706 RESET SWITCH IC703 3 RESET 1 +2.5V 3 IC702 REG 1 2 IC705 REG 5 Q717 T901 SUB TRANSFORMER 1 EVER+4V 3 D902-905 IC901 REG 1
22
22
HCD-RV600D/RV600DJ
Tuner Section
CF1
Q1 RF IF AMP Q2
AM/FM IF MPX IC11 CF2 FM TUNED LEVEL 1 FM IF L OUT 13 R OUT 14 AM IF IN 4 IFT11 AM MIX OUT 2 DI DO CL CE MASTER CONTROL IC1104(1/3) 26 27 28 25 ST-DOUT ST-DIN ST-CLK ST-CE AMP Q11 R-CH L-CH
E
MAIN SECTION (Page 24)
+B (FE2,3) TM1 FE2 8 ANT IN FM 75 IF OUT 1 F OUT 3 VT 4 X51 4.5MHz
A+12V PLL IC51 10 FM IF IN FM 1 XIN AM OSC VCO STOP 22 XOUT IF REQ 16 20 19 18 FM OSC AOUT AIN PD DO DI CL CE 12 7 15 9 8 6 4 5 3 DO DI CL CE
A+12V RV11
G AM
11 24 12 10
AM/FM OSC FM VCO STOP IF REQ MUTE
A+12V
20 RDS-INT DECORDER 18 PLL IN OUT 17 DECORDER 16 IN 21 AM RF IN 22 AFC 23 AM OSC 9 VCC TUNED 6 STEREO 7 FM-DET 8 A+12V T11 NULL 22 ST MUTE 21 RDS-DATA 24 TUNED 23 STEREO
10 1 3 2 11 7 4 9 6 A+12V 8
RB41
· RCH is omitted due to same as LCH · Signal Path : FM : AM
23
23
HCD-RV600D/RV600DJ
Ver 1.2 2003.10 Main Section
Q110 MREQ IC301 D/A CONVERTER MDI MC ML 13 DATA 14 CLK 15 LAT · RCH is omitted due to same as LCH · Signal Path : FM : DVD : DIGITAL OUT : PB(DECK A) : PB(DECK B) : REC(DECK B) IC305 DIGITAL AUDIO SELECTOR DATA0 DVD DSP SECTION (Page 21) 13 12 14 3 4 2 10 9 11 6 7 5 1 IC303 OPTICAL OUT SELECTOR IEC958 DOUT IC501 DIGITAL OUT OPTICAL OPTICAL DIGITAL OUT CDSEL 12 8 5 1,2 IC504 4 TIMING 1 LOUT 7 ROUT 8 IC505 BUFFER TH201,Q216,217 OVERHEAT DET IC201 POWER AMP RY281 LOUT 18 Q103 MUTE 15 10 11 RCH Q251 OVERLOAD DET RCH DBFB SW Q101 DBFB DET RCH DC DET Q236,237 Q235 PROTECT DET 5 7 IC1203 DIGITAL ECHO RV1201 MIC-LEVEL RV1202 ECHO-LEVEL IC601 REC/PB AMP R-CH 32 A-IN(L) DECK-B REC/PB HEAD 34 B-IN(L) EQ-OUT(L) 28 21 REC-OUT(L) REC-IN(L) 24 R-CH Q604 Q605 ERASE HEAD T601 Q601 BIAS OSC Q602,603 TC12V A/B 13 MUTE ON/OFF 14 REC.MUTE OFF/ON 15 R-CH PB-OUT(L) 26 Q610,611 AMS DET IC303 AMS AMP 72 AMS-IN STK-MUTE 84 REAR-RELAY 87 FRONT-RELAY 88 FNN 50 56 31 33 32 SURR-SW VOL-CLK VOL-DATA2 VOL-DATA1
M61519-DATA M61519-CLOCK
A
PCMD BCK-ZIBA BCK LRCK-ZIBA LRCK XCK 768FS
2 DATA(SEL)
1 BCK(SEL)
3 LRCK
16 MCLK
RCH MUTE Q108 42 3 4 5 6 7 2 8
IC102 SOUND CONTROLLER SUR1 INA1 INB1 INC1 IND1 INEX1 MIC RECB1
TM201
FRONT SPEAKER L
J101 IN L IN R VIDEO(MD) OUT L OUT R J1001 VIDEO INPUT L R
TUNER SECTION (Page 23) R-CH
E
TUNER
DVD TUNER TC LINE GAME MIC
Q281,282 +VH
BBB1 17 BBA1 16
RCH RCH
R
DATA CLOCK
Q233,234 RELAY SW
D230,231 AC DET Q232 MUTE R CH Q152 HP MUTE J1101 PHONES AC3
R-CH
21 22
R-CH IC1201(1/2) MIC AMP IC1201(2/2) MIC AMP
IC1104(2/3) MASTER CONTORL
J1201 MIC
DECK-A PB HEAD
REAR/CEN MUTE 52 SW-MUTE 51 LINE-MUTE 83 D734,735 AC AC4 DET
HP Q702,703,707 LINE MUTE
F
DVD SYS SECTION (Page 22)
Q701
76 PB-A/B 78 PB-MUTE 79 REC-MUTE
Q713, Q708-710 FAN SW
FAN
VIDEO-SW 55 Q608,609 TC BLOCK B SHUT A SHUT B PLAY A PLAY B HALF A HALF B REC REV B REC FWD CAP M+ Q615,616 CAP M DRIVE Q617,618 B TRIG DRIVE Q613,614 A TRIG DRIVE R-CH SWITCH 75 BAIS 77 TC-RELAY 1 81 80 71 70 69 68 67 66 B-SHUT A-SHUT B-PLAY A-PLAY B-HALF A-HALF B-REC.REV B-REC.FWD DVD DSP SECTION (Page 21) V C Y 7 3 IC503 VIDEO BUFFER 4 V-IN 2 C-IN 6 Y-IN 12 CY-IN V-OUT.A V-OUT.B C-OUT Y-OUT.A Y-OUT.B CY-OUT.A CY-OUT.B CB-OUT.A CB-OUT.B CR-OUT.A CR-OUT.B 30 31 33 27 28 24 25 21 22 18 19 Q501,502 WIDE IC502 VIDEO SELECTOR J502 S VIDEO OUT Y PB/CB PR/CR J501 COMPONENT VIDEO OUT 2 J503 VIDEO OUT
C Y
65 CAP M-CONT
B
CB/R CR/B
14 CB-IN 16 CR-IN
B TRG M+
61 B-TRIG
A TRG M+
60 A-TRIG
24
24
HCD-RV600D/RV600DJ
6-2. Circuit Boards Location
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.)
Note on Schematic Diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. f · : internal component. · 5 : fusible resistor. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · · · · · A : B+ Line. B : B Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : FM f : AM E : PB (DECK A) d : PB (DECK B) G : REC (DECK B) c : digital out g : MD (VIDEO) Abbreviation EA : Saudi Arabia model MY : Malaysia model SP : Singapore model TH : Thai model MX : Mexican model E51 : Chilean and Peruvian model E3 : 240V AC Area in E model B C E Note on Printed Wiring Boards: · X : parts extracted from the component side. · : Pattern from the side which enables seeing. · Indication of transistor.
C Q B E
SUB TRANSFORMER board
TRANSFORMER board
These are omitted.
PANEL board
REMOTE board
These are omitted.
MICROPHONE board MAIN board SUB PANEL board TC board
·
· ·
·
MOTOR board DIODE board SENSOR board DRIVER board RF board MB board
VIDEO board
FRONT AMP board REG board
25
25
HCD-RV600D/RV600DJ
6-3. Printed Wiring Board RF Board · See page 25 for Circuit Boards Location.
IC001
(Page 28)
· Semiconductor Location
Ref. No. D001 D002 IC001 Q001 Q002 Location B-5 B-5 A-5 C-3 C-3
26
26
HCD-RV600D/RV600DJ
6-4. Schematic Diagram RF Board · See page 53 for Wavefoms. · See page 62 for IC Block Diagrams.
CN002 29P C027 R023 820
B C031 1000p CH R026 12k E
JL005
C023 22p CH
C021 22p CH
C022 22p CH
C020 22p CH
C025
C028
B
C030
B
B
CN001 24P
C024
C026
R025 100 R024 0 JL007 C008
B
B
JL004
C029
B C013 B C006 10V
B C009 B
C019 5600p R022 220 C018 5600p C017 2200p C016 2200p C015 2200p C014 2200p
B B B B B B IC001 CXD1881AR
R027 0 R028 0 R029 0 C032 B JL006 JL003 R032 100 C049 B C033 B C012 B C005 10V
C042 180p CH R014 0 R001 100 E
(KHM-240AAA)
R013 0 R012 0 R011 0 R018 0 R017 0 R016 0 R015 0 C034 B JL002 JL001 C035 B
R035 0 R033 0 R041 1k R019 0 R020 0 C041 B C040 B C039 C037 330p CH C038 C036 R034 10M B
R021 0
IOP2
R005 47k
IOP1
R009 47k
R003 33
C001 6.3V
Q001 2SB1132-T100-QR L001 C010 1000p CH C002 16V
Q002 2SB1132-T100-QR L002 C011 1000p CH R010 470
R006 470
C004 16V D002 1SS355TE-17
D001 1SS355TE-17
CN003 9P
(KHM-240AAA)
C003 6.3V
R004 33
R007 33
R008 33
27
27