Text preview for : cellesse_sense_active_®_.pdf part of Philips HP 5231 Service Manual Cellesse Sense Active 8W - pag. 5
Back to : cellesse_sense_active_®_. | Home
Cellesse Sense Active HP 5231
PRODUCT INFORMATION Type appliance Voltage (mains) : 13 V adapter from mains (AC) : 220-240 V, 50/60 Hz and 110-127 V, 50/60 Hz : DC type
Introduction The Cellesse is a special massage system, designed to help to reduce or prevent the unsightly appearance of cellulite. Cellulite is the increased visibility of lumpy fat deposits through the surface of the skin. A common used description is `orange peel skin' because of its unique pitted, lumpy appearance. Cellulite should not be confused with `cellulitis', which is a medical term linked to bacterial infection of the skin. Cellulite can be reduced with the help of this product. It can never be completely eliminated and will return when neglected. Cellesse can smooth the cellulite layer inside the skin by up to 49 % in one month, if the appliance is used 3 times a week for 15 minutes on each leg. The Cellesse Sense Active does not reduce the fat in the fat layer.
Motor
Max. powerconsumption : 8 Watts Under pressure Number of rollers Length cord : 5 steps from 80 mbar to 250 mbar : 2 driven and 2 non-driven (small) : 2.5 m
Note: Product meets the requirements regarding interference suppression on radio and TV.
Published by Philips Domestic Appliances and Personal Care
Printed in the Netherlands
© Copyright reserved
Subject to modification
4822 729 22059 99/02
PCS 101 219
FUNCTIONAL DESCRIPTION OF THE HP5231 CELLESSE Function of the Cellesse The product is connected to the mains and the ON/OFF switch (A) is set to level 1 5. The electronic suppression switch (C) switches on the motor of the massage rolls (E). The Pump B starts to function. The pump (B) only starts to function if the appliance is in a proper contact with the skin so a vacuum of at least 80 mbar can be reached. Once a vacuum of 80 mbar is reached the small indicator lamp on the front of the appliance lights up to show that a proper contact is made. 3 To avoid painful sucking in of the skin, the vacuum stop buttons (F) 2 can be operated so that the 4 vacuum is eliminated. The Cellesse only functions properly if the product is put 1 0 5 properly on the skin so that the pump can build up a vacuum in the sucking area. (G) Cleaning and maintenance Never immerse the appliance in water or rinse it. For the best results, clean the appliance after every treatment session with a moist cloth and, if necessary, a drop of washingup liquid. Make sure the filter does not get damp. Do not use alcohol, acetone, benzine, abrasives, scourers etc., to clean the appliance. Cleaning the rollers To clean the rollers select Level 1. Wipe the rollers clean with a damp cloth.
3 2 4 1
0
5
Cleaning the hand-strap (1) The hand-strap with claps can be washed in a washing machine at max.40 °C. Washing may slightly change the colour of the strap.
VACU-stop Button
TP6
+13V not on W4 PCB red not on
PCB
F On/off Switch + Suppression Switch Level 1-5 A
W1_1 TP11 TP13 not on W7 PCB red not on
PCB
C3
R1 Q1
A3
TP7
A4
W5 red
red W3 TP5 SOCKET-PCB W1_2 TP4 TP3
R2
R3 W1_2 LEDPCB not on W3_1 PCB blue blue W8 TP14 W6 TP8 TP12
M
M1
M
M2
W9_1
El. Suppression Switch C Switches on the motor D automatically at 80 mBar underpressure
Pump B
A1 P-JACK
P
TP1 TP2 W1_1
A3
D3 TP9
A5
W3_2 TP10 W9_2
R4
TP15 Q2 C4 R5
DAP0777
Sleeves
Sucking Area G Rolls E
PCS 101 220
EXPLODED VIEW
1
2 D
101 A 16 102 B E 5 F 4 3 I 19 8 20 17
A 103 7 104 E I 11 C 18 10 D 21 G C H B D G H B C F 105 106 105 A 9
6
14 12 13
D Screws C and D (2x) = 3
x x
l 9
DAP0793
PARTS LIST Pos. description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 flexible hand-strap hand support set housing parts set vacuum buttons vacuum stop unit power unit pump pcb set tubes vacuum control unit on/off switch adjusting knob filter (5x) sieve support rollers (2x) set damping rubbers 103 + 104 set screws: consisting of Screw A + B pouch rattle spring power jack Led green adapter EURO adapter UK adapter USA adapter JPN adapter Korea adapter Australia adapter Brazil adapter China adapter CND adapter Mexico adapter Argentina 220-240 V 220-240 V 110-127 V 100 V 220 V 240 V 115-220 V 220 V 110-127 V 110-127 V 240 V item 12,13,14 item 103,104 item 19,20 item 105 (2x), 106 (1x) item 18 Item 4 (2x) included service code 4822 498 10737 4822 404 10995 4822 310 11367 4822 310 11368 4822 310 11369 4822 310 11371 4822 310 11372 4822 310 11373 4822 310 11374 4822 310 11375 4822 410 12477 4822 310 11376 4822 480 10273 4822 310 11377 4822 310 11378 4822 310 11379 4822 600 10867 4822 492 32876 4822 265 11618 4822 130 83081 4822 219 10618 4822 219 10619 4822 219 10621 4822 219 10622 4822 219 10623 4822 219 10624 4822 219 10625 4822 219 10626 4822 219 10627 4822 219 10628 4822 219 10668 4822 736 17014 4822 736 17015 4822 736 17016
DISASSEMBLY ADVICE To open the product
Remove Flexible Hand-strap 1 Set Adjusting knob (11) to pos. 5 Remove Adjusting knob (11)
1
1
2
Remove Screw A + B Remove Screw C
C
Remove Screw cover A + B
Remove Screw cover D (2x) Remove Screw D (2x)
A
B
D (2x)
Directions for use: E, P, GR, TR Directions for use: DK, S, N, SF Directions for use: UK, F, D, NL, I
N.B. Screw Cover A + B will be damaged, when it is removed For this reason, both covers are supplied free when you order items 3 10 and 15.
N.B. Components with numbers from 100 and higher cannot be ordered separately
PCS 101 221
ASSEMBLY TIPS + TEST CRITERIA AND CONTROLS + POSSIBLE COMPLAINTS ASSEMBLY TIPS Adjusting knob (11) ; Before assembling the adjusting knob (11), set the cam of the adjusting unit 10 to the indicated position. Spring: Before replacing
3 2
4
1
0
5
2 mm
Adjusting the hand-strap N.B.
1
1
2
To avoid dust from getting into the pump, the suction opening has been closed with a plastic cap. Remove the plastic cap before assembling. After the product has been repaired, it should function properly and has to meet the safety requirements as laid down and officially established at this moment.
2
3
L
M
4
S
TEST CRITERIA AND CONTROLS Voltage Total product Adapter: Primary voltage Secondary voltage Pump Motor rollers 13.0 V 220-240 V 13.0 V 400 mA if < 12.5 V adapter is defective 13.0 V 13.0 V 180 mA ± 10% 180 mA ± 10 % Ampere 380 mA ± 10 %
POSSIBLE COMPLAINTS Status 1. Switch in "OFF" position 2. Switch set to level 1 Failure Pump functions Pump doesn't function Cause ON/OFF switch defective Adapter defective ON/OFF switch defective Internal wiring broken Defective PCB Motor pump defective Filter is clogged Electronic switch defective Defective PCB Electronic switch defective Defective PCB Sleeves got loose Vacuum stop defective Gearing motor defective Pump clogged filter missing Internal wiring broken
3. Switch set to level 1-5 and product not placed on the skin 4. Switch set to level 1-5 and product properly placed
LED burns
Product doesn't function
To check, if the product functions properly. - Remove sieve (13). - Set the switch to level 1. The rollers should rotate continuously and the LED doesn't burn. - Cover the suction opening with the thumb. The LED lights up. - Press the vacuum stop-buttons. The LED goes out and the rollers stop rotating.
PCS 101 222