Text preview for : IP_03k12e.pdf part of Nissan Micra [ver. K12] Service Manual Instrument Panel - pag. 12+12+6
Back to : I_instrument_panel_®_.rar | Home
INSTRUMENT PANEL
I BODY
A
SECTION
B
INSTRUMENT PANEL
C
D
CONTENTS
PRECAUTIONS ......................................................... 2 . Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................. 2 . Precautions ............................................................. 2 . CLIP AND FASTENER .............................................. 3 . List of Table ............................................................. 3 . INSTRUMENT PANEL ASSEMBLY .......................... 4 . Component Parts Location ...................................... 4 . Removal and Installation ......................................... 5 . WORK ITEM TABLE ............................................. 5 . REMOVAL ............................................................ 5 . REMOVAL AND INSTALLATION OF INSTRUMENT PAD ........................................................... 9 . REMOVAL AND INSTALLATION OF CONSOLE BOX. ..................................................................... 9 . CONSOLE BOX ................................................. 10 . Disassembly and Assembly ................................... 11 . INSTRUMENT PANEL PAD ............................... 11 . GLOVE BOX COVER ASSEMBLY ..................... 11 .
E
F
G
H
IP
J
K
L
M
IP-1
PRECAUTIONS
PFP:00001 PRECAUTIONS Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
EIS004OW
The Supplemental Restraint System such as "AIR BAG" and "SEAT BELT PRE-TENSIONER", used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system safely is included in the SRS and SB section of this Service Manual. WARNING: q To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision which would result in air bag inflation, all maintenance must be performed by an authorized NISSAN/INFINITI dealer. q Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see the SRS section. q Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
Precautions
q
EIS004OX
Disconnect both battery cables in advance. q Disconnect air bag system line in advance. q Never tamper with or force air bag lid open, as this may adversely affect air bag performance. q Be careful not to scratch pad and other parts. q When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which may get in the way with cloth. q When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape. q Keep removed parts protected with cloth. q If a clip is deformed or damaged, replace it. q If an unreusable part is removed, replace it with a new one. q Tighten bolts and nuts firmly to the specified torque. q After re-assembly has been completed, make sure each part functions correctly. q Remove stains in the following way. Water-soluble stains: Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth. Oil stain: Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely. Then wipe the area with a soft dry cloth. q Do not use any organic solvent, such as thinner or benzine.
IP-2
CLIP AND FASTENER CLIP AND FASTENER List of Table
Symbol No. Shape Removal and installation
PFP:76906
A
EIS004OH
B
C
D
E
MIIB0017E
F
G
H
IP
J
K
L
M
IP-3
INSTRUMENT PANEL ASSEMBLY INSTRUMENT PANEL ASSEMBLY Component Parts Location
PFP:68200
SMA for VIN >SJNxxAK12U1000000
EIS004OI
MIIB9075E
IP-4
INSTRUMENT PANEL ASSEMBLY
1. 4. 7. Passenger air bag module Combination meter Switch panel finisher 2. 5. 8. 11. Instrument mask Cluster lid "A" Instrument panel under tray Fuse block lid 3. 6. 9. 12. 15. 18. 21. 24. 27. 30. Upper instrument panel Instrument side mask (RH) Side ventilator grille (RH) Cluster lid C Instrument side mask (LH) Glove box lid Steering column cover Console box Steering column protector Console mask
EIS004OJ
A
10. Instrument finisher 13. Audio 16. Side ventilator grille (LH) 19. Tray 22. Steering lock escutcheon 25. Coin holder 28. Central ventilator grille (LH)
14. Glove box striker 17. Glove box cover assembly 20. Air conditioner finisher 23. Instrument panel stay cover 26. Instrument panel & pad 29. Central ventilator grille (RH)
B
C
D
Removal and Installation
WORK ITEM TABLE
Component Parts Location
SMA for VIN >SJNxxAK12U1000000
Instrument panel &Brake pad Instrument pad [1] [2] [3] Upper instrument panel [1] [2] Combination meter [1] [2] Audio, CarWings unit
E
F
[1]
Note
A. Front pillar garnish B. Upper instrument panel C. Steering lock escutcheon D. Instrument panel under tray E. Switch panel finisher F. Steering column cover G. Combination switch H. Cluster lid "A" I. Combination meter J. Instrument finisher K. Cluster lid C L. Air conditioner finisher M. Instrument panel stay cover N. Glove box lid O. Glove box cover assembly P. Side ventilator grille Q. Instrument side mask R. Passenger seat air bag module S. Steering wheel T. Instrument panel & pad U. Instrument pad
IP-5 IP-6 IP-6 IP-6 IP-6 IP-6 IP-6 IP-7 IP-7 IP-7 IP-7 IP-7 IP-8 IP-8 IP-8 IP-8 IP-8 IP-8 IP-8 IP-9 IP-9
[1] [2] [3] [4] [5] [6] [7] [8] [9] [ 10 ] [ 11 ] [ 12 ]
[ 2 ]Note
G
[4] [5] [6] [7] [8] [9] [ 10 ] [4] [5] [3] [4] [3]
H
IP
J
K
[ 13 ] [ 14 ] [ 15 ] [ 16 ] [ 17 ] [ 18 ] [ 19 ] [ 20 ] [ 16 ] [ 11 ] [ 12 ] [ 13 ] [ 14 ] [ 15 ]
L
M
[ ]: The number shows the removal order. CAUTION: q Only applies to combinations of Car-Wings unit and MD/CD integrated AM/FM electronic tuner radio, and of pocket deck and MD/CD integrated AM/FM electronic tuner radio. Other companies can only be removed using procedures [3] and [4].
REMOVAL A. Front Pillar Garnish
Refer to EI-19, "BODY SIDE TRIM" in EI section.
IP-5
INSTRUMENT PANEL ASSEMBLY
B. Upper Instrument Panel
1. Insert a screwdriver wrapped with cloth into the instrument mask back notch to remove the instrument mask. When vehicle has sunload sensor, disconnect the sensor harness. Refer to ATC-67, "SUNLOAD SENSOR" in ATC section. Insert a screwdriver, etc., wrapped with cloth into the upper instrument panel passenger side back edge and disengage metal clips and lift up panel. Hold the lifted up part by hand, remove metal clips engaged in instrument pad, and remove upper instrument panel.
2. 3.
C. Steering Lock Escutcheon
Pull toward vehicle and remove. CAUTION: To install, align key cylinder end bottom protrusion with escutcheon inside notch and install.
D. Instrument Panel Under Tray
1. 2. Disengage upper metal clips, hold bottom lid by hand, pull panel forward, and disengage metal clips. Remove being careful of interference from surrounding metal objects.
MIIB0019E
E. Switch Panel Finisher
Hold lid side (arrow area) by hand, disengage metal clips, and then pull forward and disengage plastic clips to remove.
MIIB0020E
F. Steering Column Cover
Upper 1. To make it easier to remove lower side, face steering pad top downward. (Tilt right side at about 160°) 2. Tilt down steering column and remove screw (1) facing front of vehicle. 3. Disengage hooks and remove. Lower q Remove screws (3). CAUTION: Pull out being careful of interference with surrounding objects.
G. Combination Switch
Refer to LT-187, "LIGHTING AND TURN SIGNAL SWITCH" in LT section and WW-46, "Removal and Installation of Front Wiper and Washer Switch" (models without rain sensor) or WW-80, "Removal and Installation of Front Wiper and Washer Switch" (models with rain sensor) and WW-109, "Removal and Installation of Rear Wiper and Washer Switch" in WW section.
IP-6
INSTRUMENT PANEL ASSEMBLY
H. Cluster lid "A"
1. 2. 3. Tilt down steering column. Pull cluster lid A forward and remove hooks and mounting clips. While being careful of surrounding interference, remove from steering right side.
A
B
C
MIIB0021E
D
I. Combination Meter
After removing screws, remove harness connector, and then place combination meter top to the rear and remove.
E
F
G
PIIA1424J
H
J. Instrument Finisher
q
q
Insert a screwdriver wrapped with tape into the bottom of instrument finisher, and pull up and remove finisher. (Vehicles with pocket decks) Open pocket, insert a screwdriver wrapped with tape into the bottom of the instrument finisher at the top, and remove the finisher.
IP
J
K
MIIB0022E
K. Cluster Lid C
1. 2. 3. Remove screws and metal clips, hold lid bottom by hand, and pull straight out. Separate and remove audio harness connector. After removal, separate the center ventilator grille and audio equipment. Refer to ATC-80, "DUCTS AND GRILLES" in ATC section, MTC-57, "DUCTS AND GRILLES" in MTC section, DI64, "Removal and Installation of Drive Computer" in DI section and AV-12, "Removal and Installation of Audio Unit" in AV section.
MIIB0023E
L
M
L. Air Conditioner Finisher
Refer to ATC-63, "Removal and Installation" in ATC section and MTC-43, "Removal and Installation" in MTC section.
IP-7
INSTRUMENT PANEL ASSEMBLY
M. Instrument Panel Stay Cover
1. 2. Remove at LH/RH mounting clips. Pull instrument stay cover toward rear of vehicle, disengage metal clips, orient straight above cup holder, and remove.
MIIB0024E
N. Glove Box Lid
1. Remove glove box pin and then remove glove box lid.
MIIB0025E
O. Glove Box Cover Assembly
1. 2. 3. Pull out tray (only vehicles equipped with tray). Remove screws shown in figure, and then remove glove box cover assembly. After removal, separate parts. Refer to IP-11, "GLOVE BOX COVER ASSEMBLY" in "Disassembly and Assembly".
MIIB0026E
P. Side Ventilator Grille
Refer to ATC-80, "DUCTS AND GRILLES" in ATC section and MTC-57, "DUCTS AND GRILLES" in MTC section.
Q. Instrument Side Mask
1. 2. Rotate instrument side mask to center of vehicle forward insertion area, disengage metal clips and plastic hooks, and remove. Pull out inserted area and remove from vehicle.
MIIB0027E
R. Passenger Seat Air Bag Module
Refer to SRS-40, "FRONT PASSENGER AIR BAG MODULE" in SRS section.
S. Steering Wheel
Refer to SRS-36, "DRIVER AIR BAG MODULE" and SRS-38, "SPIRAL CABLE" in SRS section.
IP-8
INSTRUMENT PANEL ASSEMBLY
T. Instrument Panel & Pad
1. 2. 3. Tilt down steering column. Remove screws, and remove instrument panel and pad from passenger door opening. After removal, separate parts. Refer to IP-11, "INSTRUMENT PANEL PAD" in "Disassembly and Assembly". Remove instrument pad screws (6). Remove metal clips (4) engaged in instrument panel, and remove instrument pad.
A
B
U. Instrument Pad
1. 2.
C
REMOVAL AND INSTALLATION OF INSTRUMENT PAD Removal
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Remove front pillar garnish. Refer to IP-5, "A. Front Pillar Garnish" . Remove upper instrument panel. Refer to IP-6, "B. Upper Instrument Panel" . Remove steering lock escutcheon. Refer to IP-6, "C. Steering Lock Escutcheon" . Remove switch panel finisher. Refer to IP-6, "E. Switch Panel Finisher" . Remove steering column cover. Refer to IP-6, "F. Steering Column Cover" . Remove combination switch. Refer to IP-6, "G. Combination Switch" . Remove cluster lid "A". Refer to IP-7, "H. Cluster lid "A"" . Remove combination meter. Refer to IP-7, "I. Combination Meter" . Remove instrument panel finisher. Refer to IP-7, "J. Instrument Finisher" . Remove cluster lid "C". Refer to IP-7, "K. Cluster Lid C" . Remove mask. Refer to IP-7, "L. Air Conditioner Finisher" . Remove glove box lid. Refer to IP-8, "N. Glove Box Lid" . Remove glove box cover assembly. Refer to IP-8, "O. Glove Box Cover Assembly" . Remove side ventilator grille (LH/RH). Refer to IP-8, "P. Side Ventilator Grille" . Remove passenger air bag module. Refer to IP-8, "R. Passenger Seat Air Bag Module" .
D
E
F
G
H
IP
Installation
Install in the reverse order of removal.
J
K
REMOVAL AND INSTALLATION OF CONSOLE BOX. Removal
1. 2. 3. 4. 5. 6. For manual transmission vehicles, remove shift knob from shift lever. Pull up parking brake Remove inside key antenna (center console) (vehicles with key system only) connector from console box. Remove console mask. Move the seat and remove the screws. Lift up the console box and remove the front side clips.
L
M
Installation
Install in the reverse order of removal.
IP-9
INSTRUMENT PANEL ASSEMBLY
CONSOLE BOX
MIIB0028E
1.
Console box
2.
Console mask
3.
Cup holder
1. 2.
Remove console mask. (hooks: 2 locations) Open and secure the cup holder at the position where the lock opens, and then in this state pull it straight up to remove it.
MIIB0029E
IP-10
INSTRUMENT PANEL ASSEMBLY Disassembly and Assembly
INSTRUMENT PANEL PAD
EIS004OK
A
B
C
D
E
F
G
H
IP
MIIB0030E
1.
Instrument pad
2.
Instrument panel
.
J
GLOVE BOX COVER ASSEMBLY
K
L
M
MIIB0031E
1.
Glove box cover
2.
Tray bracket assembly
IP-11
INSTRUMENT PANEL ASSEMBLY
IP-12