Text preview for : dvd sanyo hd60 MTK1379 Mtk 1369 Service Manual.pdf part of Sanyo HD60 Service Manual Dvd Player - Pag. 75
Back to : dvd_player_®_.rar | Home
CONTENTS
1. PRECAUTIONS-------------------------------------------------------------------------------------------------------------------- 1
1-1 SAFETY PRECAUTIONS ---------------------------------------------------------------------------------------------------------- 1
1-2 SERVICING PRECAUTIONS ------------------------------------------------------------------------------------------------------ 2
1-2-1 General Serving Precautions -------------------------------------------------------------------------------------------- 2
1-2-2 Insulation Checking Procedure------------------------------------------------------------------------------------------ 3
1-3 ESD PRECAUTIONS ------------------------------------------------------------------------------------------------------------- 3
2. REFERENCE INFORMATION ------------------------------------------------------------------------------------------------ 4
2-1 COMPONENT DESCRIPTIONS --------------------------------------------------------------------------------------------------- 4
2-1-1 DVD SANYO HD60 PUH ------------------------------------------------------------------------------------------------ 4
2-1-2 DVD Processor Chip (MTK1379)--------------------------------------------------------------------------------------- 6
2-1-4 20-Pin, 24-Bit, 96kHz Stereo D/A with Volume Control (WM8720)-----------------------------------------------15
2-1-5 Serial EEPROM, 2K (256 x 8) (24C16) -------------------------------------------------------------------------------17
2-1-7 512K X 16 Bit X 2 Banks Synchronous DRAM (A43L0616) -------------------------------------------------------20
3. PRODUCT SPECIFICATIONS------------------------------------------------------------------------------------------------23
4. OPERATING INSTRUCTIONS -----------------------------------------------------------------------------------------------24
BASIC OPERATIONS -----------------------------------------------------------------------------------------------------------------24
ADVANCE OPERATIONS -------------------------------------------------------------------------------------------------------------26
SETUP OPERATIONS -----------------------------------------------------------------------------------------------------------------34
KARAOKE OPERATIONS ------------------------------------------------------------------------------------------------------------44
MP3 OPERATIONS -------------------------------------------------------------------------------------------------------------------45
KODAK PICTURE CD OPERATIONS -----------------------------------------------------------------------------------------------47
MAINTENANCE & TROUBLESHOOTING ------------------------------------------------------------------------------------------48
5. DISASSEMBLY AND REASSEMBLY ---------------------------------------------------------------------------------------50
6. TROUBLESHOOTING----------------------------------------------------------------------------------------------------------51
7. ELECTRICAL PART LIST-----------------------------------------------------------------------------------------------------52
8. BLOCK DIAGRAM --------------------------------------------------------------------------------------------------------------63
9. CIRCUIT DIAGRAMS ----------------------------------------------------------------------------------------------------------65
10. WIRING DIAGRAM -----------------------------------------------------------------------------------------------------------73
1. PRECAUTIONS
1-1 Safety Precautions
1) Before returning an instrument to the customer, always
make a safety check of the entire instrument, including, but
not limited to, the following items:
(1) Be sure that no built-in protective devices are defective
or have been defeated during servicing.
(1) Protective shields are provided to protect both the
technician and the customer. Correctly replace all
missing protective shields, including any remove for
servicing convenience.
(2) When reinstalling the chassis and/or other
assembly in the cabinet, be sure to put back in place
all protective devices, including, but not limited to,
AC Leakage Test
nonmetallic control knobs, insulating fish papers,
adjustment and compartment covers/shields, and
Any measurements not within the limits specified
isolation resistor/capacitor networks. Do not operate
herein indicate a potential shock hazard that must be
this instrument or permit it to be operated without all
eliminated before returning the instrument to the
protective devices correctly installed and functioning.
customer.
(2) Be sure that there are no cabinet opening through which
(4) Insulation Resistance Test Cold Check-(1) Unplug the
adults or children might be able to insert their fingers
power supply cord and connect a jumper wore
and contact a hazardous voltage. Such openings
between the two prongs of the plug. (2) Turn on the
include, but are not limited to, excessively wide
power switch of the instrument. (3) Measure the
cabinet ventilation slots, and an improperly fitted
resistance with an ohmmeter between the jumpered
and/or incorrectly secured cabinet back cover.
AC plug and all exposed metallic cabinet parts on the
instrument, such as screwheads, antenna, control
(3) Leakage Current Hot Check-With the instrument
shafts, handle brackets, etc. When an exposed
completely reassembled, plug the AC line cord
metallic part has a return path to the chassis, the
directly into a 120V AC outlet. (Do not use an
reading should be between 1 and 5.2 megohm. When
isolation transformer during this test.) Use a leakage
there is no return path to the chassis, the reading must
current tester or a metering system that complies with
be infinite. If the reading is not within the limits
American National Standards institute (ANSI) C101.1
specified, there is the possibility of a shock hazard,
Leakage.
and the instrument must be re-pared and rechecked
before it is returned to the customer.
Current for Appliances and underwriters Laboratories
(UL) 1270 (40.7). With the instrument's AC switch
first in the ON position and then in the OFF position,
measure from a known earth ground (metal water pipe,
conduit, etc.) to all exposed metal parts of the
instrument (antennas, handle brackets, metal cabinets,
screwheads, metallic overlays, control shafts, etc.),
especially and exposed metal parts that offer an
electrical return path to the chassis.
Any current measured must not exceed 0.5mA.
Reverse the instrument power cord plug in the outlet
Insulation Resistance Test
and repeat the test.
1
2) Read and comply with all caution and safety related 5) Components, parts, and/or wiring that appear to have
notes non or inside the cabinet, or on the chassis. overheated or that are otherwise damaged should be
replaced with components, parts and/or wiring that
3) Design Alteration Warning-Do not alter of add to the meet original specifications. Additionally determine
mechanical or electrical design of this instrument. the cause of overheating and/or damage and, if
Design alterations and additions, including but not necessary, take corrective action to remove and
limited to, circuit modifications and the addition of potential safety hazard.
items such as auxiliary audio output connections,
might alter the safety characteristics of this instrument 6) Product Safety Notice-Some electrical and mechanical
and create a hazard to the user. Any design alterations parts have special safety-related characteristics which
or additions will make you, the service, responsible are often not evident from visual inspection, nor can
for personal injury or property damage resulting there the protection they give necessarily be obtained by
from. replacing them with components rated for higher
voltage, wattage, etc. Parts that have special safety
4) Observe original lead dress. Take extra care to assure characteristics are identified by shading, an ( ) or a
correct lead dress in the following areas: ( ) on schematics and parts lists. Use of a substitute
(1) near sharp edges, (2) near thermally hot parts (be replacement that does not have the same safety
sure that leads and components do not touch characteristics as the recommended replacement part
thermally hot parts), (3) the AC supply, (4) high might created shock, fire and/or other hazards.
voltage, and (5) antenna wiring. Always inspect in all Product safety is under review continuously and new
areas for pinched, out-of-place, or frayed wiring. Do instructions are issued whenever appropriate.
not change spacing between a component and the
printed-circuit board, Check the AC power cord for
damage.
1-2 Servicing Precautions
CAUTION: Before servicing Instruments covered by this of its electrical assemblies unless all solid-state
service manual and its supplements, read and follow the device heat sinks are correctly installed.
Safety Precautions section of this manual. d. Always connect a test instrument's ground lead to
the instrument chassis ground before connecting the
Note: If unforeseen circument create conflict between the test instrument positive lead. Always remove the test
following servicing precautions and any of the safety instrument ground lead last.
precautions, always follow the safety precautions. Note: Refer to the Safety Precautions section ground
Remember; Safety First lead last.
(2) The service precautions are indicated or printed on the
1-2-1 General Serving Precautions cabinet, chassis or components. When servicing,
(1) a. Always unplug the instrument's AC power cord from follow the printed or indicated service precautions
the AC power source before (1) removing or and service materials.
reinstalling any component, circuit board, module or (3) The components used in the unit have a specified flame
any other instrument assembly. (2) disconnecting resistance and dielectric strength.
any instrument electrical plug or other electrical When replacing components, use components which
connection. (3) connecting a test substitute in have the same ratings, by ( ) or by ( ) in the
parallel with an electrolytic capacitor in the circuit diagram are important for safety or for the
instrument. characteristics of the unit. Always replace them with
b. Do not defeat any plug/socket B+ voltage interlocks the exact replacement components.
with which instruments covered by this service (4) An insulation tube or tape is sometimes used and some
manual might be equipped. components are raised above the printed wiring board
c. Do not apply AC power to this instrument and/or any for safety. The internal wiring is sometimes clamped
2
to prevent contact with heating components. Install 1-2-2 Insulation Checking Procedure
such elements as they were. Disconnect the attachment plug from the AC outlet and
(5) After servicing, always check that the removed screws, turn the power ON. Connect the insulation resistance meter
components, and wiring have been installed correctly (500V) to the blades of the attachment plug. The insulation
and that the portion around the serviced part has not resistance between each blade of the attachment plug and
been damaged and so on. Further, check the insulation accessible conductive parts (see note) should be more than
between the blades of the attachment plus and 1 Megohm.
accessible conductive parts.
Note: Accessible conductive parts include metal panels,
input terminals, earphone jacks, etc.
1-3 ESD Precautions
Electrostatically Sensitive Devices (ESD) solder removal devices not classified as "anti-static"
can generate electrical charges sufficient to damage
Some semiconductor (solid static electricity) devices can ESD devices.
be damaged easily by static electricity.
Such compo9nents commonly are called Electrostatically (5) Do not use freon-propelled chemicals. These can
Sensitive Devices (ESD). Examples of typical ESD devices generate electrical charges sufficient to damage ESD
are integrated circuits and some field-effect transistors and devices.
semiconductor chip components. The following techniques (6) Do not remove a replacement ESD device from its
of component damage caused by static electricity. protective package until immediately before you are
ready to install it. (Most replacement ES devices are
(1) immediately before handling any semiconductor packaged with leads electrically shorted together by
components or semiconductor-equipped assembly, conductive foam, aluminum foil or comparable
drain off any electrostatic charge on your body by conductive materials).
touching a known earth ground. Alternatively, obtain
and wear a commercially available discharging wrist (7) Immediately before removing the protective materials
strap device, which should be removed for potential from the leads of a replacement ES device touch the
shock reasons prior to applying power to the unit protective material to the chassis or circuit assembly
under test. into which the device will be installed.
(2) after removing an electrical assembly equipped with CAUTION: Be sure no power is applied to the chassis or
ESD devices, place the assembly on a conductive circuit, and observe all other safety precautions.
surface such as aluminum foil, to prevent electrostatic
charge buildup or exposure of the assembly. (8) Minimize bodily motions when handling unpackaged
replacement ESD devices. (Otherwise harmless
(3) Use only a grounded-tip soldering iron to solder or motion such as the brushing together of your clothes
unsolder ESD device. fabric or the lifting of your foot from a carpeted floor
can generate static electricity sufficient to damage an
(4) Use only an anti-static solder removal devices. Some ESD device).
3
2. Reference Information
2-1 Component Descriptions
2-1-1 DVD SANYO HD60 PUH
Connector Pin Definition
I/F Signals I/O Pin #
F- 1
F+ 2
T+ 3
T- 4
C 5
D 6
CD/DVD 7
RF 8
A 9
B 10
F 11
GND-PD 12
VC 13
VCC 14
E 15
NC 16
VR-CD 17
VR-DVD 18
LD-CD 19
MD 20
HFM 21
NC 22
LD-DVD 23
GND-LD 24
4
4. Block Diagram
Disc
MT1369 MT1369
(RF AMP) (Decode/Servo) AuDdio D/A
Disc motor unit Laser Driver ATAPI WM8720
Laser
Equalizer Buffer Manager
pickup
Error Gen Demodulator SDRAM
Error Correction 1*16MHzX2
PLI
Focus & Tracking
Video D/A
Loading
CS4955
Spindle Focus Track Sied Loading
Motor Coil Coil Motor Motor 1/F
Conn
(frant pannel)
BA5954FP
4ch motor Drive
BA6208
Spindle Motor Drive
Fiash 80c52
Memory System Controller
Spindle motor single for CLV
8Mbit
5
2-1-2 DVD Processor Chip (MTK1379)
* Features
Single-chip DVD video decoder in a 208-pin PQFP package
Supports MPEG-1 system and MPEG-2 program streams
Programmable multimedia processor architecture
Compatible with Audio CD, Video CD, VCD 3.0, and Super Video CD (SVCD)
DVD Navigation 1
Built-in content Scrambling System (CSS)
- Audio
Built-in Karaoke key-shift function
DolbyTM Digital 2-channel down mix audio output for DolbyTM
Dolby Pro Logic
Linear PCM streams for24 bit / 96KHz
Concurrent S/PDIF out and 2-channel audio output
Sensaura Dolby Digital Virtual Surround
DTS Digital Surround 2-channel down mix stereo output
S/PDIF output for encoded AC-3, DTS Digital output or Linear PCM
- Peripheral
Glueless interface to DVD loaders (ATAPI or A/V bus I/F)
Bi-directional 12C audio interface
8 general-purpose auxiliary ports
Single 27MHz clock input
- Smart Technology
SmartZoomTM for motion zoom & pan
SmartZoomTM for NTSC to PAL conversion and vice versa
SmartZoomTM for video error concealment
* Functional Description
6
* Pinout Diagram
7
8
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
54
53
FG
A17
A16
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
TRO
FOO
FMO
IOA7
IOA6
IOA5
IOA4
IOA3
IOA2
IOA1
IOA0
IREF
DMO
DVSS
DVSS
JITFN
JITFO
LPFIP
IOA20
IOA19
IOA18
LPFIN
LPIOP
LPION
LPFOP
LPFON
DVDD2
DVDD3
DVDD2
HIGHA7
HIGHA6
HIGHA5
HIGHA4
HIGHA3
HIGHA2
HIGHA1
HIGHA0
PLLVSS
APLLVSS
PLLVDD3
55 216
PWMOUT2
PWMOUT1
56 APLLVDD3 RFIP 215
TROPENPWM
57 ALE RFIN 214
IOOE# RFDTSLVN
58 213
59 IOWR# RFDTSLVP 212
IOCS# ADCVDD3 211
60
DVSS PWM2VREF 210
61
UP1_2 PWMVREF 209
62
UP1_3 HRFZC 208
63
UP1_4 RFRP_AC 207
64
UP1_5 RFRP_DC 206
65
UP1_6 RFLEVEL
66 205
DVDD3 FEI
67 204
UP1_7 CSO 203
68
UP3_0 TEI
69 202
UP3_1 TEZISLV
70 201
INT0# RFSUBI
71 200
IR ADIN
72 199
DVDD2 ADCVSS
73 198
UP3_4 BDO
74 197
UP3_5 SLCK
75 196
UWR# SDEN
76 195
URD# SDATA
77 194
DVSS WOBSI
78 193
RD7 UDGATE
79 192
RD6 DVDD3
80 191
RD5 IDGATE
81 190
RD4 VFO13
82 DVDD2 DVSS 189
83 RD3 PRST
188
84 RD2 XTALI 187
85 RD1 XTALO 186
86 RD0 DVDD3 185
87 RWE# SPBCK 184
88 CAS# SPLRCK 183
89 RAS# DVDD2 182
90 RCS# SPDATA 181
91 180
MT1379_216
BA0 SPMCLK
92 DVSS HSYN 179
93 RD15 DVSS 178
94 RD14 YUV7 177
95 RD13 VSYN 176
96 RD12 BLANK# 175
97 DVDD3 ICE 174
98 RD11 YUV6/R 173
99 RD10 YUV5/B 172
100 RD9 DACVSSA 171
101 RD8 YUV4/G 170
102 DVSS DACVDDA 169
103 CLK YUV3/CVBS 168
104 CLE DACVSSB 167
105 166
RA11 YUV2/Y
106 165
RA9 DACVDDB
107 164
RA8 YUV1/C
108 163
DMVDD3 DACVSSC
YUV0/CIN
DACVDDC
DVDD3
DVDD2
DVDD3
DVDD2
DVDD3
SPDIF
RD31
RD30
RD29
RD28
RD27
RD26
RD25
RD24
RD23
RD22
RD21
RD20
RD19
RD18
RD17
RD16
ALRCK
VREF
RA7
RA6
RA5
RA4
RA0
RA1
RA2
RA3
FS
DVSS
RA10
DVSS
DVSS
DVSS
ABCK
ACLK
BA1
DMVSS
DQM1
DQM0
DQM3
DQM2
MC_DATA
ASDATA0
ASDATA1
ASDATA2
ASDATA3
ASDATA4
U4 MT1379E
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
SMD LQFP-216
PIN DESCRIPTON
PIN Symbol Type Description
Current reference input.it generate reference current for data PLL
1 IREF Analog Input
Connect an external 100K resistor to this pin and PLLVSS.
2 PLLVSS Ground Ground for data PLL and related analog circuitry
3 LPIOP Analog output Positive output of the low pass filter
4 LPION Analog output Negative output of the low pass filter
5 LPFON Analog output Negative output of loop filter amplifiter
6 LPFIP Analog input Positive input of loop filter amplifier
7 LPFIN Analog input Negative input of loop filter amplifier
8 LPFOP Analog output Positive output of loop filter amplifier
9 JITFO Analog output RF jitter meter output
10 JITFN Analog input Negative input of the operation amplifier for RF jigger meter
11 PLLVDD3 Power Power for data PLL and related analog circuitry
12 FOO Analog output Focus servo output. PDM output of focus servo compensator
13 TRO Analog output Tracking servo output.PDM output of tracking servo compensator
Tray open output,controlled by microcontroller.
14 TROPENPWM Analog outpu This is PWM output for TRWMEN27hRW2=1 or is digital output for
TRWMEN27Hrw2=0
16 PWMOUT2 Analog outpu The general PWM output
17 DVDD2 Power 2.5V power
18 DMO Analog outpu Disk motor control output.PWM output
19 FMO Analog outpu Feed motor control. PWM output
20 FG Inout, pull up Motor Hall sensor input
21 DVSS Ground Ground
22 HIGHA0 Inout, pull up Microcontroller address 8
23 HIGHA1 Inout, pull up Microcontroller address 9
24 HIGHA2 Inout, pull up Microcontroller address 10
25 HIGHA3 Inout, pull up Microcontroller address 11
26 HIGHA4 Inout, pull up Microcontroller address 12
27 HIGHA5 Inout, pull up Microcontroller address 13
28 DVSS Ground Ground
29 HIGHA6 Inout, pull up Microcontroller address 14
30 HIGHA7 Inout, pull up Microcontroller address 15
31 AD7 Inout Microcontroller address/data 7
32 AD6 Inout Microcontroller address/data 6
33 AD5 Inout Microcontroller address/data 5
34 AD4 Inout Microcontroller address/data 4
35 DVDD3 Power 3.3V power
36 AD3 Inout Microcontroller address/data 3
37 AD2 Inout Microcontroller address/data 2
38 AD1 Inout Microcontroller address/data 1
39 AD0 Inout Microcontroller address/data 0
40 IOA0 Inout, pull up Microcontroller address 0/GPIO0
41 IOA1 Inout, pull up Microcontroller address 0/GPIO1
42 DVDD2 Power 2.5V power
43 IOA2 Inout, pull up Microcontroller address 0/GPIO2
44 IOA3 Inout, pull up Microcontroller address 0/GPIO3
45 IOA4 Inout, pull up Microcontroller address 0/GPIO4
46 IOA5 Inout, pull up Microcontroller address 0/GPIO5
47 IOA6 Inout, pull up Microcontroller address 0/GPIO6
48 IOA7 Inout, pull up Microcontroller address 0/GPIO7
49 A16 Outpu Flash address 16
50 A17 Output Flash address 17
51 IOA18 Inout Flash address 18 / GPIO10
52 IOA19 Inout Flash address 19 / GPIO11
53 IOA20 Inout Flash address20 / GPIO12
54 APLLVSS3 Ground Ground
9
PIN Symbol Type Description
55 APLLVDD3 Power 3.3V power
56 ALE Inout,pull up Microcontroller address latch enable
57 IOOE# Inout Flash output enable,active low /GPIO13
58 IOWR# Inout Flash write enable,active low /GPIO17
59 IOCS# Inout,pull up Flash chip select,active low /GPIO18
60 DVSS Ground Ground
61 UP1_2 Inout,pull up Microcontroller port 1-2
62 UP1_3 Inout,pull up Microcontroller port 1-3
63 UP1_4 Inout,pull up Microcontroller port 1-4
64 UP1_5 Inout,pull up Microcontroller port 1-5
65 UP1_6 Inout,pull up Microcontroller port 1-6
66 DVDD3 Power 3.3V power
67 UP1_7 Inout,pull up Microcontroller port 1-7
68 UP3_0 Inout,pull up Microcontroller port 3-0
69 UP3_1 Inout,pull up Microcontroller port 3-1
70 INT0# Inout,pull up Microcontroller interrupt 0,active low
71 IR Input IR control signal input
72 DVDD2 Power 2.5V power
73 UP3_4 Inout Microcontroller port 3-4
74 UP3_5 Inout Microcontroller port 3-5
75 UWR# Inout,pull up Microcontroller write strobe,active low
76 URD# Inout,pull up Microcontroller read strobe,active low
77 DVSS Ground Ground
78 RD7 Inout DRAM data 7
79 RD6 Inout DRAM data 6
80 RD5 Inout DRAM data 5
81 RD4 Inout DRAM data 4
82 DVDD2 Power 2.5V power
83 RD3 Inout DRAM data 3
84 RD2 Inout DRAM data 2
85 RD1 Inout DRAM data 1
86 RD0 Inout DRAM data 0
87 RWE# Output DRAM write enable,active low
88 CAS# Output DRAM column address strobe,active low
89 RAS# Output DRAM row address strobe,active low
90 RCS# Output DRAM chip select,active low
91 BA0 Output DRAM bank address 0
92 DVSS Ground Ground
93 RD15 Inout,pull up/down DRAM data 15
94 RD14 Inout,pull up/down DRAM data 14
95 RD13 Inout,pull up/down DRAM data 13
96 RD12 Inout,pull up/down DRAM data 12
97 DVDD3 Power Power3.3V
98 RD11 Inout,pull up/down DRAM data 11
99 RD10 Inout,pull up/down DRAM data 10
100 RD9 Inout,pull up/down DRAM data 9
101 RD8 Inout,pull up/down DRAM data 8
102 DVSS Ground Ground
103 CLK Output DRAM clock
104 CLE Output DRAM clock enable
105 RA11 Output DRAM address bit 11 or audio serial data 3 (channel 7/8)
106 RA9 Output DRAM address 9
107 RA8 Output DRAM address 8
108 DMVDD3 Power 3.3V power
109 DMVSS Ground Ground
110 RA7 Output DRAM address 7
111 DV33 Power 3.3V power
112 RA6 Output DRAM address 6
113 RA5 Output DRAM address 5
10
PIN Symbol Type Description
114 RA4 Output DRAM address 4
115 DVSS Ground Ground
116 DQM1 Output Mask for DRAM input/output byte 1
117 DQM0 Output Mask for DRAM input/output byte 0
118 BA1 Output DRAM bank address 0
119 RA10 Output DRAM address 10
120 DVDD2 Power 2.5V power
121 RA0 Output DRAM address 0
122 RA1 Output DRAM address 1
123 RA2 Output DRAM address 2
124 RA3 Output DRAM address 3
125 DVSS Ground Ground
126 RD31 Inout,pull up/down DRAM data 31
127 RD30 Inout,pull up/down DRAM data 30
128 RD29 Inout,pull up/down DRAM data 29
129 RD28 Inout,pull up/down DRAM data 28
130 DVDD3 Power 3.3V power
131 RD27 Inout,pull up/down DRAM data 27
132 RD26 Inout,pull up/down DRAM data 26
133 RD25 Inout,pull up/down DRAM data 25
134 RD24 Inout,pull up/down DRAM data 24
135 DVSS Ground Ground
136 DQM3 Output Mask for DRAM input/output byte 3
137 DQM2 Output Mask for DRAM input/output byte 2
138 RD23 Inout,pull up/down DRAM data 23
139 RD22 Inout,pull up/down DRAM data 22
140 DVDD2 Power 2.5V power
141 RD21 Inout,pull up/down DRAM data 21
142 RD20 Inout,pull up/down DRAM data 20
143 RD19 Inout,pull up/down DRAM data 19
144 RD18 Inout,pull up/down DRAM data 18
145 DVSS Ground Ground
146 RD17 Inout,pull up/down DRAM data 17
147 RD16 Inout,pull up/down DRAM data 16
148 ABCK Output Audio bit clock
(1) Audio left/right channel clock (2)Trap value in power-on reset.
149 ALRCK Input,pull down
1:use external 373, 0:use internal 373
150 DVDD3 Power 3.3V power
151 ACLK Inout Audio DAC master clock (384/256 audio sample frequency)
152 MC_DAT Input Microphone serial input
153 SPDIF Output SPDIF output
154 ASDATA0 Input,pull down Audio serial data 0 (left/right channel)
155 ASDATA1 Input,pull down Audio serial data 1 (surround left/surround right channel)
156 ASDATA2 Input,pull down Audio serial data 2 (center/LFE channel)
157 MUTE Output Audio Mute Signal
158 ASDATA4 Input,pull down Audio serial data 4
159 DACV33C Power 3.3V power
160 VREF output
161 FS
162 YUV0/CIN
163 DACVSSC Ground Ground
164 YUV1 Output Video data output bit 1
165 DACVDDB Power 3.3V Power
166 YUV2 Output Video data output bit 2
167 DACVSSB Ground Ground
168 YUV3/CVBS Output CVBS video output
169 DACV33A Power 3.3V power
170 YUV4/G Output Video data output bit 4
171 DACVSSA Ground Ground
172 YUV5/B Output Video data output bit 5
11
PIN Symbol Type Description
173 YUV6 Output Video data output bit 6
174 ICE Input,pull down Microcontroller ICE mode enable
175 FS1 output
176 VSYN Inout Vertical sync / GPIO16
177 YUV7 Output Video data output bit 7
178 DVSS Ground Ground
179 HSYN Inout Horizontal sync / GPIO15
182 DVDD2 Power 2.5V power
185 DVDD3 Power 3.3 power
186 XTALO Output Crystal output
187 XTALI Input Crystal input,27MHz
188 PRST Input,pull down Power on reset input, active high
189 DVSS Ground Ground
195 SDATA Output RF serial data input
196 SDEN Output RF serial data latch enable
197 SLCK Output RF serial clock output
198 BDO Input,pull down Flag of defect data status input
199 ADCVSS Ground Ground
200 ADIN Analog input General A/D input
202 TEZISLV Analog input Tracking error zero crossing low pass input
203 TEI Analog input Tracking error input
204 CSO Analog input Central servo input
205 FEI Analog input Focus error input
206 RFLEVEL Analog input Sub beam add input or RFRP low pass input
207 RFRP_DC Analog input RF ripple detect input
208 RFRP_AC Analog input RF ripple detect input (through AC coupling)
209 HRFZC Analog input High frequency RF ripple zero crossing
210 PWMVREF Analog input A reference voltage input for PWM circuitry.A typical value of 2.8v
211 PWM2VREF Analog input A reference voltage input for PWM circuitry.A typical value of 1.4v
212 ADCVDD3 Power 3.3V power
215 RFIN Analog input Negative input of RF differential signal
216 RFIP Analog input Positive input of RF differential signal
MT1336
GENERAL DESCRIPTION
MT1336 is a high performance CMOS analog front-end IC for both CD_ROM driver up to 48xs and DVD-ROM driver up
to 16xs. It also supports DVD-RAM read up to 4xs Version 2. It contains servo amplifiers to generate focusing error,
3-beam tracking error, 1 beam radial push-pull signal, RF level and SBAD for servo functions. It also includes DPD
tracking error signal for DVD_ROM application. For DVD-RAM disks, there are also Differential Push-Pull (DPP) method
for generating tracking signal and Differential Astigmatic Detection (DAD) for processing focusing signal. Programmable
equalizer and AGC circuits are also incorporated in this chip to optimize read channel performance. In addition, this chip
has dual automatic laser power control circuits for DVD-ROM (DVD-RAM) and CD-ROM seperately and reference
voltage generators to reduce external components. Programmable functions are implemented by the access of internal
register through bi-directional serial port to configure modes selection.
FEATURES
. RF equalizer with programmable fc from 3MHz to 70MHz and programmable boost from 3db to 13db.
. MT1336 supports at least eight different kinds of pick-up heads with versatile input configuration for both RF input stages
and servo signal blocks.
. Versatile on-line AGC.
. 3 beams tracking error signal generator for CD_ROM application.
. One beam differential phase tracking error (DPD) generator for DVD_ROM application.
. Differential push pull tracking error (DPP) generator for DVD_RAM application.
12
. Focusing error signal generator for CD-ROM, DVD-ROM and DVD-RAM (DAD method).
. RF level signal generator.
. Sub-beam added signal for 3 beams CD_ROM.
. One beam push-pull signal generator for central servo application.
. High speed RF envelop detection circuit with bandwidth up to 400KHz for CD-ROM.
. Defect and Blank detection circuits
. Dual automatic laser power control circuits with programmable level of LD monitor voltage.
. Vref-1.4V voltage and V2ref=2.8V voltage generators.
. V20=2.0V voltage for pick-up head reference.
. Bi-directional serial port to access internal registers.
. 128-pin LQFP
Block Diagram.........................................P.3
Pin Assignment and Description....................P.4-9
Functions
1.) RF Path Description......................P. 10-13
2.) Servo Signal................................P. 14-17
. Focusing Error
. Central Servo
. Tracking Error
. RFLVL & SBAD (LVL)
3.) ALPC & RFRP ( RF Ripple).............P. 18
4.) WOBBLE Detection.......................P. 19
Command Access Timings...........................P. 20
Programmable I/O ....................................P. 21
Register
1.) Register Map...............................P. 22-24
2.) Register Description......................P. 25-50
MT1336 PIN DESCRIPTIONS
Pin Numbers Symbol Type Description
LQFP128
RF Flag interface
23 DEFECT Digital input Flag of bad data output status
RF SIO interface
56 SCLK Digital input RF serial clock input
58 SDEN Digital input RF serial data enable
59 SDATA Digital IO RF serial data IO
60 RST Digital input Reset (active high)
55 XCK16M Digital input 16.9MHz for verification
RF SERVO interface
40 UDGATE Digital input Control signal for DVD-RAM
41 IDGATE Digital input Control signal for DVD-RAM
38 VFO13 Digital input DVD-RAM Header signal
RF
100 DVDA Analog input AC coupled DVD RF signal input A
99 DVDB Analog input AC coupled DVD RF signal input B
98 DVDC Analog input AC coupled DVD RF signal input C
97 DVDD Analog input AC coupled DVD RF signal input D
95 DVDRFIN Analog input AC coupled DVD RF signal input RFIN
13
96 DVDRFIP Analog input AC coupled DVD RF signal input RFIP
94 CDA Analog input AC coupled CD RF signal input A
93 CDB Analog input AC coupled CD RF signal input B
92 CDC Analog input AC coupled CD RF signal input C
91 CDD Analog input AC coupled CD RF signal input D
90 OSN Analog RF Offset cancellation capacitor connection
89 OSP Analog RF Offset cancellation capacitor connection
85 CEQP Analog RF Offset cancellation capacitor connection
84 CEQN Analog RF Offset cancellation capacitor connection
88 RFGC Analog RF AGC loop capacitor connecting for DVD-ROM
87 RFGCU Analog RF AGC loop capacitor connecting for DVD-ROM
86 RFGCI Analog RF AGC loop capacitor connecting for DVD-ROM
101 MA Analog input DC coupled DVD-RAM main-beam RF signal input A
102 MB Analog input DC coupled DVD-RAM main-beam RF signal input B
103 MC Analog input DC coupled DVD-RAM main-beam RF signal input C
104 MD Analog input DC coupled DVD-RAM main-beam RF signal input D
105 SA Analog input DC coupled DVD-RAM sub-beam RF signal input A
106 SB Analog input DC coupled DVD-RAM sub-beam RF signal input B
110 SC Analog input DC coupled DVD-RAM sub-beam RF signal input C
111 SD Analog input DC coupled DVD-RAM sub-beam RF signal input D
108 IR Analog External current bias resistor (R=20K)
119 AGC1 Analog Wobble AGC loop1 capacitor
121 AGC2 Analog Wobble AGC loop2 capacitor
122 AGC3 Analog Wobble AGC loop3 capacitor
127 RFSUBO Analog output Header push-pull RF output signal
1 WOBSO Analog output Wobble signal output
6 RFOP Analog output RF positive output
7 RFON Analog output RF negative output
TRACKING ERROR
32 DPFN Analog DPD amplifier negative input
33 DPFO Analog DPD amplifier output
61 DPDMUTE Digital input DPD mute control input
116 TNI Analog input 3 beam satellite PD signal negative input
115 TPI Analog input 3 beam satellite PD signal positive input
21 TEO Analog Output Tracking error output
FOCUSING ERROR & RF LEVEL & CENTRAL SERVO SIGNAL
112 CDFOP Analog input CD focusing error positive input
113 CDFON Analog input CD focusing error negative input
18 FEO Analog output Focusing error output
19 LVL Analog output RF level output
20 CSO Analog output Central servo signal output
ALPC
124 MDI1 Analog input Laser power monitor input
125 LDO1 Analog Output Laser driver output
123 MDI2 Analog input Laser power monitor input
126 LDO2 Analog Output Laser driver output
RF RIPPLE
26 CRTP Analog RF top envelop filter capacitor connecting
27 CRTPLP Analog Defect level filter capacitor connecting
25 HRFRP Analog output High frequency RF ripple output or Blank detector's output
24 LRFRP Analog output Low frequency RF ripple output
POWER
67,69 AVDD Power Master PLL Filter power
65,73 AGND GND GND for Master PLL Filter
64 AVDD Power DPD Power
62 AGND GND DPD GND
109 AVDD Power RF path Power
107 AGND GND RF path GND
114 SVDD Power Servo Power
117 SGND GND Servo GND
2,120 WAVDD Power Wobble Power
14
128,118 WAGND GND Wobble GND
5 AVDDO Power Power for RF output
8 AGNDO GND GND for RF output
14 AVDDT Power Power for trimming PAD
12 AGNDT GND GND for trimming PAD
22 VDDP Power Peak Detection Power
31 GNDP GND Peak Detection GND
37,54 VDD Power Serial I/O Power
39,57 GND GND Serial I/O GND
REFERENCE VOLTAGE
16 VREFO Analog output Reference voltage 1.4V
15 V2REFO Analog output Reference voltage 2.8V
17 V20 Analog output Reference voltage 2.0V
ALPC TRIMMING
9 TM1 Analog input Trimming pin for ALPC1
10 TM2 Analog input Trimming pin for ALPC1
11 TM3 Analog input Trimming pin for ALPC2
13 TM4 Analog input Trimming pin for ALPC2
HIGH SPEED TRACK COUNTING
29 TRLP Analog Low-pass filter capacitor connecting
28 TRLPA Analog Low-pass filter capacitor connecting
30 HTRC Digital output High speed track counting digital output
PCS
74 HALLSIN Analog input Negative input of amplifier for hall sensor signal
75 REFSIN Analog input Positive input of amplifier for hall sensor signal
76 SINPHI Analog output Amplifier output for hall sensor signal
71 HALLCOS Analog input Negative input of amplifier for hall sensor signal
72 REFCOS Analog input Positive input of amplifier for hall sensor signal
70 COSPHI Analog output Amplifier output for hall sensor signal
FOR MONITOR ONLY
81 MON Analog output
80 MOP Analog output
66 VCON Analog output
77 SWO Analog output Output from mux of SW1 & SW2
78 SW2 Analog input External input for servo input select
79 SW1 Analog input External input for servo input select
FOR SERIAL I/O
42 IO0
43 IO1
44 IO2
45 IO3
46 IO4
47 IO5
48 IO6
49 IO7
50 IO8
51 IO9
52 IOA
53 IOB
2-1-4 20-Pin, 24-Bit, 96kHz Stereo D/A with Volume Control (WM8720)
Features modes:
Performance: -Hardware mode:system clock, reset, mute,
-102dB SNR (`A' weighted @48kHz), de-emphasis
-THD: -95dB @ 0dB FS -Serial control mode: mute, de-emphasis, digital
5V or 3.3V supply operation attenuation(256 steps), zero mute, phase
Sampling frequency: 8kHz to 96kHz reversal, power down
Input data word: 16 to 24-bit Compatible with PCM1720
Hardware or SPI compatible serial port control
15
Description features including on-chip mute, attenuation and
The WM820 is a high performance stereo DAC phase reversal. A hardware controlllable interface is
designed for audio applications such as CD, DVD, also available.
home theatre systems, set top boxes and digital TV.
The WM8720 supports data input word lengths from The programmable data input port supports a variety
16 to 24-bits and sampling rates up to 96kHz. The of glueless interfaces to popular DSPs, audio
WM8720 consists of a serial interface port, digital decoders and S/PDIF and AES/EBU receivers.
interpolation filter, multi-bit sigma delta modulator and
stereo DAC in a small 20-pin SSOP package. The APPLICATIONS
WM8720 also includes a digitally controllable mute
and attenuator function on each channel. . CD, DVD audio
. Home theare systems
The WM8720 supports a variety of connection . Set top boxes
schemes for audio DAC control. The SPI-compatible . Digital TV
serial control port provides access to a wide range of
BLOCK DIAGRAM
PIN DESCRIPTIONS
PIN NAME TYPE DESCRIPTION
1 PWDN Digital input Powerdown control; low is ON, high is POWER OFF, Interal pull-down.
2 SCKI Digital input System clock input(256 or 384fs).
3 TEST Digital output Reserved.
4 ML/I2S Digital input Latch enable (software mode) or input format selection (hardware mode)
Internal pull-up.
5 MC/IWL Digital input Serial control data clock input (software mode) or input word length
selection (hardware mode). Internal pull-up.
6 MD/DM Digital input Serial control data input (software mode) or de-emphasis selection
(hareware mode). Internal pull-up.
7 RSTB Digital input Reset input-active low. Internal pull-up.
16
8 ZERO Digital output Infinite zero detect-active low. Open drain type output with active
pull-down.
9 VOUTR Analogue output Right channel DAC output.
10 AGND Supply Analogue ground supply.
11 AVDD Supply Analogue positive supply.
12 VOUTL Analogue output Left channel DAC output.
13 CAP Analogue output Analogue internal reference.
14 BCKIN Digital input Audio data bit
15 DIN Digital input Serial audio data input.
16 LRCIN Digital input Sample rate clock input.
17 MUTE Digital IO Mute control pin, input or automute output.
Low is not mute, high is mute, Z is automute.
18 MODE Digital input Mode select pin. Low is software mode, high is hardware control.
Internal pull-down.
19 DVDD Supply Digital positive supply.
20 DGND Supply Digital ground supply.
Note:
Digital input pins have Schmitt trigger input buffers.
2-1-5 Serial EEPROM, 2K (256 x 8) (24C16)
* Features
Low-Voltage and Standard-Voltage Operation
-5.0 (V CC = 4.5V to 5.5V)
-2.7 (V CC = 2.7V to 5.5V)
-2.5 (V CC = 2.5V to 5.5V)
-1.8 (V CC = 1.8V to 5.5V)
Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K) or 2048 x 8 (16K)
2-Wire Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bi-directional Data Transfer Protocol
100 kHz (1.8v, 2.5V, 2.7V) and 400 kHz (5V) Compatibility
Write Protect Pin for Hardware Data Protection
8-Byte Page (1K, 2K), 16-Byte Page (4K, 8K, 16K) Write Modes
Partial Page Writes Are Allowed
Self-Timed Write Cycle (10 ms max)
High Reliability
- Endurance: 1 Million Write Cycles
- Data Retention: 100 Years
- ESD Protection: >3000V
Automotive Grade and Extended Temperature Devices Available
8-Pin and 14-Pin JEDEC SOIC, 8-Pin PDIP, 8-Pin MSOP, and 8-Pin TSSOP Packages
* Pin Configurations
* Pin Description
Pin Name Function
17
A0-A2 Address Inputs
SDA Serial Data
SCL Serial Clock input
WP Write Protect
NC No Connect
2-1-6 8M-BIT [1Mx8/512Kx16] CMOS FLASH MEMORY
FEATURES
· 1,048,576 x 8/524,288 x 16 switchable
· Single power supply operation
- 5.0V only operation for read, erase and program
operation
· Fast access time: 70/90/120ns
· Low power consumption
- 50mA maximum active current
- 0.2uA typical standby current
· Command register architecture
- Byte/word Programming (7us/12us typical)
- Sector Erase (Sector structure 16K-Bytex1,
8K-Bytex2, 32K-Bytex1, and 64K-Byte x15)
· Auto Erase (chip & sector) and Auto Program
- Automatically erase any combination of sectors with
Erase Suspend capability.
- Automatically program and verify data at specified
address
· Erase suspend/Erase Resume
- Suspends sector erase operation to read data from,
or program data to, another sector that is not being
erased, then resumes the erase.
· Status Reply
- Data polling & Toggle bit for detection of program and
erase operation completion.
· Ready/Busy pin (RY/BY)
- Provides a hardware method of detecting program
or erase operation completion.
· Sector protection
- Sector protect/chip unprotect for 5V/12V system.
- Hardware method to disable any combination of
sectors from program or erase operations
- Tempory sector unprotect allows code changes in
previously locked sectors.
· 100,000 minimum erase/program cycles
· Latch-up protected to 100mA from -1V to VCC+1V
· Boot Code Sector Architecture
- T = Top Boot Sector
- B = Bottom Boot Sector
· Low VCC write inhibit is equal to or less than 3.2V
· Package type:
- 44-pin SOP
18
- 48-pin TSOP
· Compatibility with JEDEC standard
- Pinout and software compatible with single-power
supply Flash
19
2-1-7 512K X 16 Bit X 2 Banks Synchronous DRAM (A43L0616)
Features
JEDEC standard 3.3V power supply
LVTTL compatible with multiplexed address
Dual banks / Pulse RAS
MRS cycle with address key programs
- CAS Latency (2,3)
- Burst Length (1,2,4,8 & full page)
- Burst Type (Sequential & interleave)
All inputs are sampled at the positive going edge of the system clock
Burst Read Single-bit Write operation
DQM for masking
Auto & self refresh
64ms refresh period (4K cycle)
50 Pin TSOP (II)
Pin Configuration
20
21
Block Diagram
Pin Descriptions
Symbol Name Description
CLk System Clock Active on the positive going edge to sample all inputs
CS Chip Select Disables or Enables device operation by masking or enabling
all inputs except CLK, CKE a