Text preview for : food_processor_©_.pdf part of Philips Domestic App. HR7723/00 HR7724/16 Service Manual Domestic Appliances and Personal Care mod. Cucina - pag. 4
Back to : food_processor_©_.pdf | Home
Cucina
Food processor HR7723/00 HR7724/16
Philips Domestic Appliances and Personal Care
Service Manual
PRODUCT INFORMATION - The food processors are equipped with mechanical and thermal safety switches. - Product meets the requirements regarding interference suppression on radio and TV. - After the product has been repaired, it should function properly and has to meet the safety requirements as laid down officially established at this moment. Automatic resettable cut-out (part of item 7) - To prevent damage due to overheating, the appliance has been equipped with an automatic cut-out system. This system will automatically cut off the power supply when the appliance overheats. If the appliance suddenly stops running: Unplug the appliance Set the knob to position 0 Let the appliance cool down for 15 minutes Plug the appliance in again Switch the appliance on again TECHNICAL INFORMATION - Motor power : HR7723 - 600 W HR7724 - 700 W Voltage : 230 V : 110 V Frequency : 50 / 60 Hz Colour : White Cordset : 125 cm Speed settings : 2 speeds + pulse Bowl capacity : 2.5 l dry ingredients 1.0 l liquids Blender capacity : 1.0 l liquids 2.0 l (max. contents) Speeds unloaded : blender drive shaft 17000 rpm (max) acc. drive shaft 2150 rpm (max) acc. drive shaft 1400 rpm (min) Weight in fancy box : HR7723/24 - 5100 g Dimensions : HR7723/24 - 420 x 280 x 360 (l x w x h) SAP coding : HR7723/00 HR7724/16
-
Safety lock (item 1) - Place the lid on the bowl in the right position. The appliance will only function if the arrow on the applinace is directly opposite the mark on the lid of the food processor bowl and the same holds for the other accessoires. The built-in safety lock will now be deblocked and you can turn the appliance on. Note that if both the blender jar and the bowl have been correctly mounted, only the blender will function. Important: - If the appliance is used without the blender jar, the appliance will not function if the screw cap has not been screwed onto the attaching hole for the blender.
Published by Philips Domestic Appliances and Personal Care
Printed in the Netherlands
© Copyright reserved
Subject to modification
4322 277 01090 02/11
HR7723/00 / HR7724/16
DISASSEMBLY- AND RE-ASSEMBLY ADVISE - A separate drawing shows how to disconnect the speed selection knob. - The top housing (item 29) can be removed by detaching the snap connections by sticking a pin (or a screwdriver) through the small round holes (3 mm dia.) in the bottom plate (item 27) and the housing (item 12). The arrows in the drawing show the locations of the holes. - In order to replace the speed selection knob, the locking lever (item 33) must be placed in its lowest position. - The accessory drive shaft (item 15) has a locking piece (item 14). - The assembly of the accessories depends on the national version. - For specific versions, the component configuration may differ from the one shown on the exploded view. However, the actual components can be distinguished by their code numbers. - Make sure that all functions, including the safety devices, are working correctly after you have completed the repair. REPAIR INSTRUCTION - No specific issues OPTIONAL (ACCESSORIES) - No specific issues
- The blender coupling on the motor shaft has been provided with the customary left-hand thread. The drive coupling (item 11) can be detached by means of a hammer and a screwdriver. Strike the screwdriver with a short sharp blow and remove the drive coupling. Or block the acc. drive wheel (item 23) and thereby the rotor shaft, by sticking a pin through the hole (5 mm dia.) in the bottom plate.
brown R
L2
Speed High and Pulse
M1 D1 1N5406
red
F1
Speed Low MAINS R1 470k N L1 C1
F2
brown F1
BF white Rotor
black blue N1 violet
F2 N
B yellow
Change-over switch in braking position
HR7723 / HR7724
PARTS LIST
Pos 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Service code 4203 065 62110 4822 214 12762 4203 065 62120 4822 532 13008 4822 462 11074 4822 361 11081 4822 361 11082 4822 466 11949 4203 065 60300 4822 502 14593 4203 065 62130 4203 065 64570 4822 214 12767 4822 402 11076 4822 535 10548 4203 065 62070 4822 466 11948 4822 535 10549 4822 530 10492 4822 492 11649 Description Print + switch lever Print plate brake Coupling lever Rubber piece Air tunnel Motor 230 V Motor 110 V Coupling fork Flex Motor screw assy Blender coupling Housing Print plate Locking piece Drive spindle Rubber sealing Locking plate Spindle assy Rubber tube Compression spring Pos 21 22 23 24 25 27 28 29 30 31 33 Service code 4822 528 11265 4822 358 10257 4822 528 11266 4822 520 10851 4822 466 11947 4203 065 64610 4203 065 64620 4203 065 64630 4203 065 64640 4822 492 11648 4203 065 64600 4203 065 62180 4203 065 62200 Description Coupling piece Tooth belt Belt wheel Bearing Mounting plate Bottom plate Blender cover Housing top Housing top Snap return spring Switch knob Switch knob Locking lever
HR7723 HR7724 HR7723 HR7724
2-4
EXPLODED VIEW
HR7723/00 / HR7724/16
11
1 28
12
2 14
29
3 13 4 15 16 17 5 18 19 20 33 31 30
21 7 22 23 24 8 19 25
9
27 10
3-4
PARTS LIST & EXPLODED VIEW ACCESSORIES
HR7723/00 / HR7724/16
70
55
62 71
52 56 63 72
60
64
65 58 66
73
75 67
59
68 74 69
Pos 52 55 56 58 59 60 62 63 64 65
Service code 4822 462 11083 4203 065 61860 4203 065 60170 4203 065 60160 4203 065 64510 4203 065 64390 4203 065 63800 4203 065 64520 4203 065 61840 4203 065 61960
Description Insert of lid Storage box (4 acc.) Kneading/mixing knife Metal knife Bowl (dry 2.5 l) Emulsifying disc Mono pusher Bowl cover Patato grating disc (opt.) Grating disc (fine/very fine)
Pos 66 67 68 69 70 71 72 73 74 75
Service code 4203 065 61950 4203 065 61970 4203 065 61980 4203 065 61830 4203 065 64530 4203 065 64540 4203 065 64550 4203 065 61890 4203 065 62220 4203 065 64650
Description Slicing disc (fine/medium) Grating disc (coarse/medium) Combi disc (slicing/grating) French fries (opt.) Insert of cover Cover Beaker Sealing ring Driven coupling Knife unit
4-4