Text preview for : SATELLITE 1700 SERIES.pdf part of Toshiba Satellite 1700 Series Field Replaceable Unit Documentation Notebook - [Part 1/2] pag. 10
Back to : Note_book_©__.part1.rar | Home
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite
TM
1700 Series
GENERAL INFORMATION
Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 1) 2. Flat head screwdriver (5mm) 3. Hex driver (5mm) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers
Before attempting any of the following procedures, make sure that the main battery and AC adaptor is not connected to the unit and the environment in which you are working on is protected from Electro-Static Discharge(ESD).
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
TM
TABLE OF CONTENTS:
1. BATTERY PACK REMOVAL 2. OPTIONAL PC CARD REMOVAL 3. MEMORY MODULE REMOVAL 4. KEYBOARD REMOVAL 5. TOP COVER REMOVAL 6. HDD REMOVAL 7. FDD REMOVAL 8. SYSTEM BOARD REMOVAL 9. CD-ROM DRIVE REMOVAL 10. MODEM MODULE REMOVAL 11. COOLING MODULE REMOVAL 12. CPU REMOVAL 13. LED BOARD REMOVAL 14. HINGE BRACKET REMOVAL 15. AUDIO BOARD REMOVAL 16. AUDIO/MEMBRANE SWITCH REMOVAL 17. 12.1'' DISPLAY MASK REMOVAL 18. FL INVERTER AND 12.1'' LCD REMOVAL 19. 13.3'' DISPLAY MASK REMOVAL 20. FL INVERTER AND 13.3'' LCD REMOVAL
Tough Enough for Today's World.
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
BATTERY PACK REMOVAL OPTIONAL PC CARD REMOVAL
TM
Battery lock
Battery pack
Battery release lever
Eject button
PC card
1. Turn the computer upside down as shown. 2. Press the battery lock and slide the battery release lever to the right and lift out the battery.
1. Pull out the eject button of the PC card to be removed. 2. Press the eject button and remove the PC card. NOTE: Before removing any PCMCIA device, make sure it is "STOPPED" in the PC Card Manager.
MEMORY MODULE REMOVAL
M2x4 black screws Memory cover Memory module
KEYBOARD REMOVAL
Latch
M2.5x3 black screws
Memory clips 1. Turn the computer upside down. 2. Remove two M2x4 black screws and remove the memory cover. 3. Push the memory clips outward and pull the memory module out of the connector on a 30 degree angle.
Keyboard holder 1. Open the display panel. 2. Remove two M2.5x3 black screws securing the keyboard holder. 3. Unlatch the keyboard holder at the top of keyboard starting from the left side.
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
KEYBOARD REMOVAL
TM
Keyboard
M2.5x3 black screws
Keyboard
Keyboard cable
JP7
JP5
IPS cable
4. Remove four M2x4 black screws securing the keyboard.
5. Set the keyboard as shown above. 6. Disconnect the keyboard cable from JP7 and IPS cable from JP5. 7. Lift out the keyboard.
TOP COVER REMOVAL
M2.5x8 silver screws M2.5x12 black screws
M2.5x10 black screw
M2.5x18 black screws
Lcd harness assy M2.5x3 black screw 1. Remove two M2.5x8 silver screws and M2.5x12 black screws securing the LCD assembly. 2. Remove one M2.5x3 black screw securing the LCD harness assembly. 3. Disconnect the LCD harness assembly from the system board.
4. Remove eight M2.5x18 black screws and one M2.5x10 black screw securing the bottom cover.
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
TOP COVER REMOVAL HDD REMOVAL
TM
M2.5x3 black screws LED cable
HDD assy handle HDD assy HDD
M2.5x8 silver screws Sound/IPS switch board JP4 Top cover 5. Disconnect the sound/IPS switch board from JP4 on the system board. 6. Disconnect the LED board cable from the LED board. 7. Remove four M2.5x8 silver screws and two M2.5x3 black screw securing the top cover assembly. 8 Remove the top cover. . M2.5x8 silver screw 1. Remove one M2.5x8 silver screw securing the HDD assembly. 2. Grasp the HDD assembly handle and pull it in the direction of the arrow. 3. Lift out the HDD assembly.
HDD REMOVAL
M2.5x4 silver screws HDD bracket
FDD REMOVAL
JP6 FDD cable
M2.5x8 silver screw
HDD
FDD assembly 4. Remove four M2.5x3 silver screws securing the HDD bracket. 5. Remove the HDD from the HDD bracket. 1. Remove one M2.5x8 silver screw securing the FDD assembly. 2. Disconnect the FDD cable from JP6. 3. Lift out the FDD assembly.
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
FDD REMOVAL
Left bracket
TM
SYSTEM BOARD REMOVAL
FDD cable
Right bracket FDD M2.5x3 black screws 1. Remove three M2.5x3 black screws securing the left and right brackets. 2. Lift out the FDD and remove the FDD cable.
M2.5x8 silver screws
Hex screws 1. Remove four hex screws at the rear of the computer. 2. Remove two M2.5x8 silver screws near the cooling module.
SYSTEM BOARD REMOVAL
PC card eject button
CD-ROM DRIVE REMOVAL
CD-ROM drive assy
M2.5x3 black screws System board 3. Push the PC Card eject button and lift out the system board as shown above. 1. Remove two M2.5x3 black screws securing the CD-ROM drive assembly. 2. Slide the CD-ROM drive assembly to the left to disconnect from system board. 3. Remove all the CD-ROM brackets.
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
MODEM MODULE REMOVAL
TM
COOLING MODULE REMOVAL
Cooling module Fan cable Modem cable Modem JP16
Mini PCI clips 1. Disconnect the modem cable from the modem board. 2. Spread the mini PCI clips securing the modem board and remove the modem board on a 30 degree angle.
Brass screws 1. Disconnect the fan cable from JP16 on the system board. 2. Remove three brass screws securing the cooling module. 3. Lift out the cooling module.
CPU REMOVAL
LED board Open
LED BOARD REMOVAL
CPU lock slot Lock
1. Using a 5mm flat head screw driver, insert the screwdriver into the CPU lock slot and turn it counterclockwise. NOTE: In order to properly lock the CPU, a 5mm flat head screwdriver must be used.
M2.5x3 black screws 1. Remove two M2.5x3 black screws securing the LED board. 2. Lift out the LED board.
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
HINGE BRACKET REMOVAL
AUDIO BOARD REMOVAL
TM
M2.5x4 silver screws
Audio board
Audio cable 1. Remove five M2.5x4 silver screws securing hinge bracket. 2. Lift out the hinge bracket. 1. Disconnect the audio cable from the audio board. 2. Remove two M2.5x4 silver screws securing the audio board. 3. Lift out the Audio board.
AUDIO/MEMBRANE SWITCH REMOVAL
Audio/membrane switch cable Audio cable
M2.5x4 silver screws
M2.5x4 silver screws
Left speaker 1. Remove four M2.5x4 silver screws securing the metal plate. 2. Lift out the metal plate
JP3
JP4
Right speaker
1. Remove two M2.5x4 silver screws securing the audio/membrane switch board. 2. Disconnect the left and right speakers from JP3 and JP4. 3. Disconnect the audio and the audio/membrane switch cables.
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
12.1" DISPLAY MASK REMOVAL
Latch
FL cable
TM
FL INVERTER AND 12.1" LCD REMOVAL
LCD module
Display mask
M2x5 brass screws
M2.5x5 black screws
LCD
Mask seals 1. Remove four mask seals at each corner of the display assembly. 2. Remove four M2.5x5 brass screws securing the display mask. 3. There are 22 latches securing the display mask. Carefully insert your fingers between the display mask and the LCD module and pry open the latches starting from the top six latches, to the five latches on the right and left sides, ending with the six bottom latches.
LCD/FL inverter cable
FL inverter board
1. Remove two M2.5x5 black screw securing FL inverter board. 2. Carefully lift up the FL inverter board and disconnect the LCD/FL inverter cable from CN1 and the FL cable from CN2. 3. Remove four M3X6 brass screws securing the LCD module. 4. Carefully rotate the LCD module from right to left of the LCD cover. 5. Disconnect the LCD/FL inverter cable from the LCD module and remove the LCD from the computer.
Tough Enough for Today's World
TOSHIBA
FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite 1700Series
13.3" DISPLAY MASK REMOVAL
Latch
FL cable
TM
FL INVERTER AND 13.3"LCD REMOVAL
LCD module
Display mask
M2x5 brass screws
M2.5x5 black screws
LCD
Mask seals 1. Remove four mask seals at each corner of the display assembly. 2. Remove four M2.5x5 black screws securing the display mask. 3. There are 22 latches securing the display mask. Carefully insert your fingers between the display mask and the LCD module and pry open the latches starting from the top six latches, to the five latches on the right and left sides, ending with the six bottom latches.
LCD/FL inverter cable cable
FL cable
1. Remove one M2.5x5 black screw securing FL inverter board. 2. Carefully lift up the FL inverter board and disconnect the LCD/FL inverter cable from CN1 and the FL cable from CN2. 3. Remove four M2X2 black screws securing the LCD module. 4. Carefully rotate the LCD module from right to left of the LCD cover. 5. Disconnect the LCD/FL inverter cable from the LCD module and remove the LCD from the computer.
Tough Enough for Today's World
TOSHIBA