Text preview for : 42HDF39.pdf part of Hitachi 42HDF39 45 page service manual # TA007 for Hitachi 42 inch color plasma monitor model # 42HDF39.
Back to : 42HDF39.part1.rar | Home
No. TA 007
HITACHI
42HDF39
SERVICE MANUAL
Caution
Be sure to read this manual before servicing. To ensure safety from fire, electric shock, injury, harmful
radiation and materials, various measures are provided in this Plasma Monitor.
Be sure to read cautionary items described in the manual before servicing.
These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that described in the operating instructions unless you are
qualified to do so.
Service Warning
1. Since the Panel Module and the front Filter are made of glass, handling the broken Module and Filter
carefully and with caution in order not to receive injury.
2. Replacement work should be started after the Panel Module and the AC/DC Power supply have
become sufficiently cool.
3. Special care should be taken when working near the display area in order not to damage its surface.
4. The Panel Module should not be touched with bare hands in order to protect its surface from
blemishes and damage.
5. It is recommended that you use clean soft gloves during the replacement work in order to protect not
only the display area of the Panel Module but also yourself.
Contents
1. Features -------------------------------------------3 8. Connection diagram ---------------------------- 29
2. Specifications ------------------------------------4 9. Wiring diagram ----------------------------------- 30 Updated 1/31/07
3. Component Names -----------------------------5 10. Basic block diagram --------------------------- 31
4. Service points ------------------------------------7 11. Printed wiring board diagram ---------------- 32
5. Adjustment ----------------------------------------8 12. Disassembly diagram ------------------------- 39
Updated 3/24/06 6. Troubleshooting --------------------------------13 13. Replacement parts list ------------------------ 41
7. Block diagram ---------------------------------- 27
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
Plasma Monitor
Ver. TA 007.2
1
CAUTION FOR SAFETY
Please read this page before repair the monitor.
The following safety precautions are designed to help you stay safe and prevent accidents during the repair
work.
Please take note of these cautionary flags.
Warning This means "Potential to sustain injury or even death."
Caution This means "Potential to sustain breakage or irreparable damage."
Also note these cautionary icons
This means "CAUTION" This means "MUST"
This means "POTENTIAL ELECTRIC
This means "DO NOT"
SHOCK"
WARNING
Follow instructions. Must use same types of wires and components.
The cabinet, chassis, and labels are parts The Monitor uses special tubes and tapes
that require attention. You must follow the made from insulated materials. Moreover,
caution notes and safety instructions some materials are kept from making
presented throughout this User Manual to contact with the PWB for the sake of
prevent damage to them or injury to safety.Internal leads are kept from hot
yourself. parts or high voltage parts by means of
clamps or other measures. As such, you
Prevent electric shock. must restored these parts to their original
Exercise caution while working on the conditions in order to prevent electric
device as the Monitor contains high shock or fire.
voltage parts and power supply.It is
possible to sustain severe injury or death Perform safety check when done.
if you accidentally touch the wrong
parts.You must disconnect the power Every part (such as removed screws,
supply while servicing, reassembling, or components, and wiring) must be
change parts. If you touch a live restored to their prior conditions after
connection it is possible to sustain severe servicing.Be sure to check everything
injury or death. that was repaired for damage or
mistakes. Also measure the insulated
impedance with a meg-ohm meter to
Use recommended components. confirm that the impedance value is more
Use only the recommended components than 4M ohm.If the impedance value is
or componentst that structurally identical less than 4M ohm, then electric shock or
to the originals. This is to ensure safety fire may result.
and reliability. Pay special attention to
parts in the parts list and circuit diagrams
Do not try to check the HDCP code and
marked with . If you use
non-recommended components, then combination circuit.
electric shock or fire may result. Never remove the shield case protecting
the HDCP code and combination circuit.
2
PRECAUTIONS
Cleaning the monitor's plasma screen panel
Before cleaning the monitor, turn it off and disconnect the power plug from the power outlet. To prevent
scratching or damaging of the plasma screen face, do not knock or rub the surface with sharp or hard objects.
Clean the screen with a soft cloth moistened with warm water and dry with a second soft cloth. If it is not
enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.
Cleaning the monitor's cabinet
Use a soft cloth to clean the monitor's cabinet and control panel. When excessively soiled, dilute a neutral
detergent in water, wet and wring out the soft cloth in it, gently clean the cabinet, and then wipe it down with a
dry soft cloth.
Never use acid/alkaline detergents, alcoholic detergents, abrasive cleaners, powder soaps, OA cleaners, car
wax, glass cleaners, and so on. They will cause discoloration, scratches or cracks.
1. Features
High definition Plasma display panel
The 42-inch color plasma display panel, with a resolution of 1024 (H) x 1024(V) pixels, creates a widescreen
picture. This panel features a thin form factor and can be hung on a wall with an optional wall mounting kit.
High Performance Digital Processor
This panel displays a wide range of personal computer signals from 640 x 400 VESA, 640 x 480 VGA to 1024
x 768, 1280 x 1024 XGA.(RGB Analog input).
Easy-to-use remote control and on-screen display system
The included remote control operates all Monitor functions. Futhermore, the on-screen display system shows
the status of the control settings in an easy-to-view fashion.
Power saving system
When connected to a VESA DPMS-compliant PC, the monitor cuts its power consumption while idle.
3
2. Specifications
Display
dimensions Approx. 42inches (922 (H) x 522 (V) mm, diagonal 1059mm)
Panel
Resolution 1024 (H) x 1024 (V) pixels
Net dimensions 1036 (W) x 773 (H) x 300 (D) mm (With stand) 1036 (W) x 713 (H) x 121 (D) mm (Without stand)
Net weight 41 kg (With stand) 33.6 kg (Without stand)
Temperatur Operating: 0°C to 40°C, Storage: -15°C to 60°C
Ambient
conditions
Relative umidity Operating: 20% to 80%, Storage: 20% to 90% (non-condensing)
Power supply AC100 - 240V, 50/60Hz
Power consumption/at standby <350W / <1W
Audio output Built in 10W + 10W (8 ) speakers
(RGB input)
ANALOG RGB input terminal (D-sub 15-pin)
Input terminals
ANALOG RGB/HDMI audio input terminal (3.5mm Stereo Mini Jack)
Input signals Video signals 0.7 Vp-p
H/V separate, TTL level [2k ]
Sync signals
H/V composite, TTL level [2k ]
Recommended signal 25 modes
(Video input)
COMPOSITE VIDEO input terminal (RCA)
L/R COMPOSITE AUDIO input terminal (RCA)
S-VIDEO input teminal (RCA)
Input terminals L/R S-VIDEO AUDIO input terminal (RCA)
Y-PB/CB PR/CR input terminal (RCA)
Input signals L/R Y-PB/CB PR/CR AUDIO input terminal (RCA)
HDMI input terminal (HDMI 19-pin)
Composite video: PAL, SECAM, NTSC3.58, NTSC4.43
Component - YCBCR/YPBPR video: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/50, 720p/60
Video signals
S-Video: PAL, SECAM, NTSC4.43, NTSC3.58
HDMI: HDMI input signal
SUBWOOFER output terminal (RCA)
TV VIDEO output terminal (RCA)
Output Signal
L/R AUDIO output terminal (RCA)
OPTICAL OUT DIGITAL AUDIO output terminal
Recommended signal 9 modes
(TV RF input)
ANALOG RF input terminal (NTSC)
Input signals Input terminals
DIGITAL RF input terminal (ATSC)
It takes at least 30 minutes to attain the maximum picture quality.
Applicable video signals for each input terminal
Signal Type RCA HDMI D-sub Remarks
Terminal Composite Video S-Video Component DVD/STB RGB
ANALOG RGB
HDMI
COMPOSITE
S-VIDEO
1080i/720p/576p/576i/480p/480i
Y-PB/CB PR/CR
inputs.
( : Avaliable)
4
3. Component names
Main unit
Control panel
Al Adjustment buttons are located on the bottom of
the control panel
Indications for each button's function can be found
on the inside of the control panel cover.
1. POWER 5. VOL
2. UP 5. LEFT
3. DOWN 6. INPUT
4. VOL 6. EXIT
4. RIGHT 7. MENU Normal Button Action
7. SELECT Button Action when MENU engaged
Power lamp
Remote-control receiver
Main power switch
The main
power switch is
located at the
back, on the
right side.
5
Remote Control
1. Power Button
2. Mute Button
3. Recall Button
4. Quick Buttons
5. PC Buttons
6. Video Buttons
7. NTSC Buttons
8. DTV Button
9. Numbers Button
10. RTN Button
11. Exit Buttons
12. Menu Button
13. Up/Down/Left/Right Button
14. SEL Button
15. Ch +/- Button
16. Vol +/- Button
17. DTV Menu Button
18. Back Button
19. OK Button
20. Fav. ch. Button
21. Info Button
22. PC ADJ. Button
23. Freeze Button
24. C.C. Button
25. Aspect Button
26. P. Mode Button
27. Zoom-/+ Button
28. MTS Button
29. PIP Swap Button
30. PIP Input Button
31. Sleep Button
6
4. Service points
Lead-free solder
This product uses lead-free solder (unleaded) to help protect the environment. Please read these instructions
before attempting any soldering work.
Caution: Always wear safety glasses to prevent fumes or molten solder from getting into
the eyes. Lead-free solder can splatter at high temperatures (600 ).
Lead-free solder indicator
Printed circuit boards using lead-free solder are engraved with an "F."
Properties of lead-free solder
The melting point of lead-free solder is 40-50 higher than leaded solder.
Servicing solder
Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended. Although servicing with
leaded solder is possible, there are a few precautions that have to be taken. (Not taking these precautions
may cause the solder to not harden properly, and lead to consequent malfunctions.)
Precautions when using leaded solder
Remove all lead-free solder from soldered joints when replacing components.
If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the
lead-free solder has been completely melted (do not apply the soldering iron without solder).
Servicing soldering iron
A soldering iron with a temperature setting capability (temperature control function) is recommended.
The melting point of lead-free solder is higher than leaded solder. Use a soldering iron that maintains a high
stable temperature (large heat capacity), and that allows temperature adjustment according to the part being
serviced, to avoid poor servicing performance.
Recommended soldering iron:
Soldering iron with temperature control function (temperature range: 320-450 )
Recommended temperature range per part:
Part Soldering iron temperature
Mounting (chips) on mounted PCB 320 ±30
Mounting (chips) on empty PCB 380 ±30
Chassis, metallic shield, etc. 420 ±30
The PWB assembly which has used lead free solder
(1) POWER/EMI PWB, AUDIO POWER PWB, RS-232 PWB, AUDIO PWB, KEY PAD PWB, IR PWB, I/O PWB,
CONNECTOR PWB, SPEAKER CONNECTOR PWB, HDMI PWB
(2) MAIN PWB
(3) ATSC BOX(Digital Tuner Module) / TUNER
(4) POWER MODULE
(5) PDP MODULE (is all lead free solder. X-SUS PWB, Y-SUS PWB, LOGIC PWB, ADDRESS PWB, SDM PWB)
7
5. Adjustment & Software Update
This model has a factory mode, where the technician can access and adjust some of the color temperature
settings. The factory mode has several different appearances, depending on the input signal.
Preliminary
To access the Factory Mode, the
Plasma Monitor must be running.
Color temperature adjustments
Follow the procedures below to make the color temperature adjustments.
Factory setting:
Cool: x=0.268 +/- 0.01, y=0.283 +/- 0.01
Warm: x=0.314 +/- 0.01, y=0.327 +/- 0.01
Netural: x=0.285 +/- 0.01, y=0.293 +/- 0.01
Black & White: x=0.335 +/- 0.01, y=0.343 +/- 0.01
Note: That a colorimetry meter (such as a Minolta CA-200) is required to measure the actual screen color
temperature.
1. Press MENU button on remote control to display the PDP Video
OSD menu. Picture Mode Natural
Brightness 0~100
Contrast 0~100
Color 0~100
Tint 0~100
Sharpness 0~31
Color Temperature Cool
Reset
2. Select to color temperature function page under VIDEO Video
item. Color Temperature Cool
3. Press SLEEP button three times to on remote control to Video
display the adjustment RGB parameter. Color Temperature Cool
Red . 0~255
4. Press to select Natural or Warm modes. Green 4. 0~255
Blue . 0~255
8
Page intentionally left blank
Page intentionally left blank
Page intentionally left blank
Page intentionally left blank
6. Troubleshooting
The flow chart shown below will help you to troubleshoot your Monitor set with it doesn't display normally.
Each procedure offers a simple way to check for system errors. Before starting, ensure that there is a signal in
and that the Monitor is turned on.
Power turn on issue
Power cannot be turn on (LED does not light)
Is the input voltage No
applied to Power
supply unit?
(CN61 )
AC inlet Power AC Fuse 5HTP10 Filter
switch TL.510A 250V PWB
Yes
Check if the Power Cord No Connect the wire
has been well connected properly. Test again
to TV?
Yes
Are the voltages applied
to CN10 pins and No
Power supply unit
CN11 pins of
Power supply unit?
Yes
PBC-Main (CN61) 110V L W
(CN10) +5V +12V +12V
(CN11) +5V +3.3V +3.3V +5V
Note: Voltage shown for CN10 and CN11 are at Power On State.
Power off voltages are 0V, except CN11 Pin 10, this voltage is
always present.
CH 1
13
No sound issue
Picture is diaplayed. But no sound
Take off the back cover and
No
check ifl wires of the speakers
terminals have been well Check
connected to the PCB-Main
and speakers ?
No sound
Yes
Are the voltages applied to No
CN2 of the power Power supply unit
supply unit?
Yes
Are the signals applied to No
P23 of the PCB-Main or PCB-I/O
PBC-Main?
Yes
No
Are there signals on
the speaker terminals?
PCB-Audio PCB-Speaker
Yes
Connector
Speakers
(CN2) +15.5~16V GND
(P23) NC L GND R
14
No picture issue
Picture is not diaplayed (LED is lighting)
Red
Is the LED red or
green ?
Green No
Is voltage applied to
CN11 (st-5v) ?
Yes
Is it the power
saving mode ?
PCB-Main Power supply
unit
Input signal
cables or
PCB-Main
Yes
Is the voltages of No
CN10/CN11 on the
power supply unit?
Power supply unit
Yes
Are the voltages applied to No
CN64 of the power
supply unit correct?
Power supply unit
Yes
Panel module
(CN10) 5V 12V
(CN11) 5V 3.3V st-5V
Note: Voltage shown for CN10 and CN11 are at Power On State.
Power off voltages are 0V, except CN11 Pin 10, this voltage is
always present.
CH 1
15
Remote Control doesn't work
Remote controller doesn't work.
Yes
Try if another Remote Replace the Remote
Controller works? Controller.
No
Check if batteries are No Put new batteries to
placed correctly? the remote control
Yes
Test
again
Take off the back cover.
Check if the wire of PCB-IR
No Connect the wire
has been well connected to
properly.
the PCB-Main?
Yes
Change the PCB-IR Yes
then check if it works.
No
Change PCB-Main then connect all
wires properly.
16
Key pad doesn't work
Key pad doesn't work.
Take off the back cover and check if
No Connect
the wire of PCB-Speaker connectoer
the wire
has been well connected to the
properly
PCB-Key Pad and PCB-Main?
Yes Test
again
Change PCB-Key Pad and
Yes
connect all wires properly.
Check if it works
Change PCB- Speaker
No
connectoer and connect all
wires properly. Check if it works
Change the PCB-Main.
17
No PC signal (Analog RGB)
No PC signal.
Check if PC source is No
Check PC by PC
working on other
Service Provider
display?
Yes
Check if the D-Sub cables No Connect the D-Sub
have been well connected cables properly
to the PDP?
Yes
Test
again
Check if the signal Yes
Adjust the signal
frequency is higher than
frequency.
1024x768 ?
Take off the back cover.
No
Change the
PCB-Main
18
NTSC TV source no signal
No NTSC TV Signal
Make sure the OSD TV
No Select to the correct
source option is correct
option
(Cable/Air)
Yes
Check if the TV cable has No
Connect the TV
been well connected to the Test
cable properly
PDP? again
Yes
Check if the "Channel No
Execute the "Channel
Search" function has been
Search" function.
done?
Yes
Check if the Assembly No
Connect the Assembly
PCB-Video has been well
PCB-Video properly.
connected?
Yes
Change the NTSC Tuner Yes
Board and check if it works.
No
Change the
PCB-Main
19
DTV source no signal
Cannot receive any digital channel
Turn the TV off
No
Is the multi I/O connector
connected with scaler board Connect it firmly
No
Is the signal received
Yes
Yes
Problem has
been resolved
No
Is the tuner connected
with antenna / cable
Connect it firmly
connector
No
Is the signal received
Yes
Yes
Problem has
been resolved
No
Be sure have done
the channel scan Make auto scan
No
Is the signal received
Yes Yes
Problem has
been resolved
Change the tuner module
20
No optical audio sound
No audio service
No
Is the multi I/O connector
connected with scaler board Connect it firmly
No
Is the audio work
Yes Yes
Yes Problem has
Is it in "MUTE" mode been resolved
No
Press "MUTE" or "VOL+"
so that audio work
No
Yes
No
Scan this channel by Problem has
Be sure this channel
using "Manual Scan" been resolved
was been locked
No
Yes Is the audio work
Yes
Change the tuner module
Problem has
been resolved
21
No signal issue (Composite, SV, YCbCr, YPbPr)
No signal
Check if the signal source Enable source and
No
is available and been well connect the signal wire
connected? properly.
Yes
Check if the PCB-I/O has
No Connect the PCB-I/O
been well connected to
the PCB-Main? properly.
Yes
Take off the back cover. Test
again
Check if Wire Ass'y 31P No
Connect Wire Ass'y 31P
has been well connected to properly to the
PCB-Main? PCB-Main.
Yes
No
Change the PCB-I/O Change
then check the signal PCB-Main board
Yes
22
No HDMI signal issue
No signal
Check if the signal source Enable source and
No
is available and been well connect the signal wire
connected? properly.
Yes
Take off the back cover.
Check if the PCB-HDMI No Connect the
has been well connected
PCB-HDMI properly.
to the PCB-Main?
Test
again
Yes
Check if Wire Ass'y 31P Connect Wire Ass'y 31P
No
has been well connected to properly to the
PCB-Main? PCB-Main.
Yes
Change the PCB-HDMI No Change
then check the signal PCB-Main board
Yes
23
Software can't be updated
Can not update software
Check if RS-232 Cable No
Connect RS-232
has been well connected
Cable properly.
to the PDP?
Yes
Take off the back cover. Test
again
Check if all wires have No
Connect the wires
been well connected to the
properly.
PCB-RS232 & PCB-Main?
Yes
Yes
Change the PCB-RS232
and see if it works?
No
Change the PCB-Main.
24
Power board issues
1. No power
NO POWER
NO Vs, Va, Vcc, STB
NG impedance check NG
FUSE
OK D001
D001
OK
NG
STB
impedance check NG
Q003/Q004
check voltage Over 130V Q003/Q004/R005 ect
OK
D020(k)-J051
OK impedance check NG
Q201
Under 130V
Q200/Q201/Q202/D210
D151, D101 etc OK
ect
See NO PICTURE & impedance check NG
SOUND Q301
Q301/Q302/Q303/D310
ect
IC101, R005
2. No picture and sound
NO PICTURE &
SOUND NO Vs, Va, Vcc,
NG
FUSE SEE NO POWER
OK
NG Over 130V
check voltage PC201, PC202, D210
Vcc
D020(k)-J051 etc
OK
Under 130V
IC001, D601~D604, RL001,
See NO PICTURE PC001, PC003, IC002 etc
25
3. No picture
NO PICTURE
NO Vs, Va, Vcc
impedance NG
check Vs LINE
OK
Open connector
CN64
impedance NG
check Va LINE
OK
OK impedance
check Vs LINE
Open connector
SW ON CN64
NG
impedance OK
D551, D550
Va:no uprise Vs:no uprise check Va LINE
Vs:down after up Va:down after up
NG
Q303, PC301, Q501,D510,
PC302, D310, Q500,PC501,
PDP module Va PDP module Vs
etc PC502,etc D351 NG NG
26
7. Block Diagram
Plasma Monitor
27
Power Module
28
8. Connection Diagram
29
9. Wiring Block Diagram
Item No. Wire Part No. HITACHI Part No. Item No. Wire Part No. HITACHI Part No. Item Board Part No. HITACHI Part No.
1 P205 Wire Ass'y W10/10P E057410010 TE02294 12 P207 FFC 50P+AI E784650506 TE02751 D IR Board(PWB-0874) 5097659801 TE03511
2 P203 Wire Ass'y W11/10P E057411001 TE02292 13 P212 Wire Ass'y W5/5P E057405011 TE02299 E RS-232 Board(PWB-0832) 5097643008 TS06665
3 P201 Wire Ass'y W2/2P E057402005 TE02291 14 P9001A Wire Ass'y W8/8P E057408006 TE02304 F Power/EMI Board(PWB-0905) 5097651912 TS06667
Parts List on page 44
4 P208 Wire Ass'y W9/9P E057409002 TE02296 Wire Ass'y W4/4P E057408005 - G Audio Power Board(PWB-0905) 5097651913 TS06666
15 P7002A
5 P9003A Wire Ass'y W4/4P E057404011 TE02305 (This wire is included in PCB-Key pad assembly) H Audio Board(PWB-0807) 5097639914 TS06668
6 P211 Wire Ass'y W5/5P E057405008 TE02298 16 P215 Wire Ass'y E057401009 TE02753 I Speaker Connector Board(PWB-0906) 5097653206 TS06671
7 P814 Wire Ass'y W3/3P E057403016 TE02755 17 P206 Wire Ass'y W20/20P E057420004 TE02295 J HDMI Board(PWB-0892) 5097652105 TS06669
8 P813 Wire Ass'y W3/2P E057403015 TE02754 Item Board Part No. HITACHI Part No. K Tuner Module 5052110027 TE03601
9 P811 Wire Ass'y E057401008 TE02761 A Main Board(PWB-0891) 5097652009 TE04071 L Power Module 6693006618 TS06011
10 P209 Wire Ass'y W4/4P E507404009 TE02297 B I/O Board(PWB-0899) 5097651805 TS06662 M ATSC Connector Board(PWB-0833) 5097642804 TS05977
11 P204 Wire Ass'y W31/30P E057431012 TE04091 C Key Pad(PWB-0874) 5097659800 TE03501 N ATSC Module 5053911108 TS07471
30
Panel Boards Layout
Y-SUS PWB X-SUS PWB
LOGIC PWB
located behind Main Board
A-BUS-R PWB
A-BUS-L PWB
See page 44 for p/n's
30a
CH 2
10. Basic Block Diagram
31
11. Printed Wiring Board Diagram
Main Board Top Side
32
Main Board Bottom Side
33
I/O Board Top Side
RS-232 Board Top Side Audio Board Top Side
34
Audio Transfer Board Top Side(L)/Bottom Side(R)
35
Power/EMI Board Top Side(L)/Bottom Side(R)
Speaker Connector Board Top Side(L)/Bottom Side(R)
Key Pad Top Side(L)/Bottom Side(R)
IR Board Top Side(L)/Bottom Side(R)
36
HDMI Board Top Side(L)/Bottom Side(R)
37
Power Board
38
12. Disassembly Diagram
Mechanical
39
Packing
40
13. Replacement Parts List
Mechanical & Packing part list
NO. DESCRIPTION PART NO.
M1 Front Cover Ass'y 5096454886
M2 Function Key E642851202
M3 Rear Cover Ass'y 5096154886
M4 SPK Cover E641105000
M5 Power Cap E641100500
M6 Edge Saddle E642678500
M7 Tape of al foil(25x580) E648006524
M8 Tape of al foil(25x980) E648006525
M9 Tape of al foil(50x20) E648006506
M10 Sponge (570x7x2.5) E642018222
M11 Sponge (985x6.5x5.5) E642018223
M12 Cable Clamp E640105200
M13 Panel Supporter Mylar E646522200
M14 Washer E646522300
M15 NON-WOVEN FABRICS E642025810
M16 GASKET 585X10X1 E642025339
M17 GASKET 963X10X1 E642025309
M18 GASKET 624X5X1 E642025316
M19 GASKET 1025X5X1 E642025315
M20 GASKET E642025349
M21 Special Screw E640223000
M22 Wire Saddle E640104007
M23 Wire Saddle E642583500
M24 Wire Saddle E642583501
M25 Washer E640229301
M26 SPONGE E642026417
M27 SPONGE-SPK E642026418
M28 SPONGE-SPK E642026419
M29 BASE ASS'Y 5095854857
M30 Tray I514104256
M31 EPS Bottom (BR) I524100256
M32 EPS Bottom (BL)
I534054356
M33 EPE Bag
M34 HS Carton I514100756
M35 EPS Top (TR) I524100156
M36 EPS Top (TL)
I534100356
M37 Grip Joint
41
M38 Clip PE Bag I533251157
M39 EPS Bottom(BM) I524100456
M40 EPE Bag I534100256
42
Electrical part list
NO. DESCRIPTION PART NO.
ASSEMBLY PCB-MAIN BOARD (PWB-0891) 5097652009
ASSEMBLY PCB-I/O (PWB-0899) 5097651805
ASSEMBLY PCB-KEY PAD (PWB-0874) 5097659800
ASSEMBLY PCB-KEY IR (PWB-0874) 5097659801
ASSEMBLY PCB-RS-232 BOARD
5097643008
(PWB-0832)
ASSEMBLY PCB-POWER/EMI (PWB-0905) 5097651912
ASSEMBLY PCB-AUDIO (PWB-0807) 5097639914
ASSEMBLY PCB-AUDIO POWER
5097651913
(PWB-0905)
ASSEMBLY PCB-CONNECTOR (PWB-0833) 5097642804
ASSEMBLY PCB-SPEAKER CONNECTOR
5097653206
(PWB-0906)
ASSEMBLY PCB-HDMI (PWB-0892) 5097652105
P301 POWER CORD E056701000
P302 D-SUB SIGNAL CABLE E057315500
P303 S-VIDEO CABLE E057304500
P304 AV CABLE E057303500
RM01 REMOTE CONTROLLER E052731079
Y001 USER'S MANUAL E030039028
Y002 WARRANTY CARD E030230010
Y003 QUICK SETUP GUIDE E030039029
Y007 WARRANTY CARD (CANADA) E030230012
GL01 SCREEN FILTER 42" 5771900152
H001 TUNER MODULE 5052110027
J001 QUICK TIE 5071000531
UA01 ATSC MODULE (w/QAM) 5053911108
UA02 POWER MODULE 6693006618
P201 WIRE ASSEMBLY W2/2P E057402005
P203 WIRE ASSEMBLY W11/10P E057411001
P204 WIRE ASSEMBLY W31/30P E057431012
P205 WIRE ASSEMBLY W10/10P E057410010
P206 WIRE ASSEMBLY W20/20P E057420004
P207 FFC 50P+AI E784650506
P208 WIRE ASSEMBLY W9/9P E057409002
P209 WIRE ASSEMBLY W4/4P E057404009
P211 WIRE ASSEMBLY W5/5P E057405008
P212 WIRE ASSEMBLY W5/5P E057405011
P215 WIRE ASSEMBLY E057401009
P811 WIRE ASSEMBLY E057401008
P813 WIRE ASSEMBLY W3/2P E057403015
P814 WIRE ASSEMBLY W3/3P E057403016
43
P9001A WIRE ASSEMBLY W8/8P E057408006
P9003A WIRE ASSEMBLY W4/4P E057404011
S811 POWER SWITCH PANASONIC E054501008
SP01 SPEAKER BOX ASSEMBLY E055100002
T811 EMI FILTER SOCKET TYPE DIT E061133007
T811A HEATED SHRINK TUBE E075500001
CABLE LOGIC-ABUSL
g 5000100119
A3(FPF29R-CBL001401)
CABLE LOGIC-XSUS
h 5000100120
A3(FPF29R-CBL001411)
CABLE LOGIC-YSUS
i 5000100121
A3(FPF29R-CBL001412)
CABLE LOGIC-ABUSR
j 5000100122
A3(FPF29R-CBL001421)
CABLE XSUS-YSUS
k 5000100123
A3(FPF29R-CBL003601)
CABLE XSUS-ABUSR
l 5000100124
A3(FPF29R-CBL003701)
Part Numbers for Boards and Assemblies
FPF29R-ABL0030 ABUS-L PWB
FPF29R-ABR0031 ABUS-R PWB
FPF29R-LGC0057 LOGIC PWB
FPF29R-XSS0037 X-SUS PWB
FPF29R-YSS0038 Y-SUS PWB
FPF42C128128UE5 PDP Panel
5052110027 TUNER MODULE
5053911108 ATSC MODULE (w/QAM)
5097639914 ASSEMBLY PCB-AUDIO
5097642804 PWB ASS'Y CONNECTOR
5097643008 ASSEMBLY PCB-RS-232 BOARD
5097651805 ASSEMBLY PCB-I/O
5097651912 ASSEMBLY PCB-POWER/EMI
5097651913 ASSEMBLY PCB-AUDIO POWER
5097652009 ASSEMBLY PCB-MAIN BOARD
5097652105 ASSEMBLY PCB-HDMI
5097653206 ASSEMBLY PCB-SPEAKER CONNECTOR
5097659800 ASSEMBLY PCB-KEY PAD
5097659801 ASSEMBLY PCB-KEY IR
5771900152 SCREEN FILTER 42"
6693006618 POWER MODULE
44