Text preview for : DCR-TRV6_lvl2.pdf part of Sony DCR-TRV6 2 files, 278 total pages, level 2 & 3 service manuals for Sony digital video camera recorder model #'s DCR-TRV6, DCR-TRV6E, DCR-TRV11, DCR-TRV11E, DCR-TRV20 and DCR-TRV20E.
Back to : DCR-TRV6_lvl2.part01.rar | Home
DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
RMT-808/809/811/812
US Model Canadian Model Korea Model
DCR-TRV6/TRV11/TRV20
SERVICE MANUAL
Level 2
Ver 1.1 2000. 06
AEP Model UK Model Australian Model Chinese Model
DCR-TRV6E/TRV11E/TRV20E
E Model Hong Kong Model Tourist Model
Photo : DCR-TRV20E RMT-811
DCR-TRV6/TRV6E/TRV11/ TRV11E/TRV20/TRV20E
J MECHANISM On the VC-240/241 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair inside the VC-240/241 board. Therefore, schematic diagram, printed wiring board and electrical parts list of the VC-240/241 board are not shown. The following pages are not shown. Schematic diagram .......................... Pages 4-17 to 4-66 Printed wiring board ......................... Pages 4-67 to 4-74 Electrical parts list ............................ Pages 6-23 to 6-44 For MECHANISM ADJUSTMENTS, refer to the "DV MECHANICAL ADJUSTMENT MANUAL J MECHANISM " (9-929-807-11). DCR-TRV6/TRV11/TRV20 : NTSC model DCR-TRV6E/TRV11E/TRV20E : PAL model
· Table showing differences is shown on page 4.
SPECIFICATIONS
-- Continued on next page --
DIGITAL VIDEO CAMERA RECORDER
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering.
2. 3.
--2--
· Table showing differences is shown on page 4.
· SUPPLIED ACCESSORIES
Check that the following accessories are supplied with your camcorder.
1 Wireless Remote Commander (1) RMT-808: DCR-TRV6/TRV6E: AUS, E, JE, CN RMT-809: DCR-TRV6E: AEP, UK RMT-812: DCR-TRV11E: AEP, UK RMT-811: DCR-TRV11/TRV11E: AUS, E, HK, JE, CN/TRV20/ TRV20E 2 R6 (size AA) battery for Remote Commander (2) 3 AC-L10A/L10B/L10C AC power adaptor (1), Mains lead (1) 4 NP-FM50 battery pack (1) 5 PC serial cable (1) DCR-TRV11/TRV11E/TRV20/TRV20E only 6 "Memory Stick" (1) DCR-TRV11/TRV11E/TRV20/TRV20E only 7 A/V connecting cable (1)
8 Shoulder strap (1) 9 21-pin adaptor (1) DCR-TRV6E: AEP, UK/TRV11E: AEP, UK/TRV20E: AEP, UK 0 Lens cap (1) qa Application software: PictureGear 4.1Lite (CD ROM) (1) DCR-TRV11/TRV11E/TRV20/TRV20E only qs Lens hood (1) DCR-TRV20/TRV20E only qd 2-pin conversion adaptor (1) DCR-TRV6E: E, HK/TRV6E: E, HK/TRV11: E, HK/ TRV11E: E, HK/TRV20: E, HK/TRV20E: E, HK qf 2-pin conversion adaptor (1) DCR-TRV6: JE/TRV6E: JE/TRV11: JE/TRV11E: JE/ TRV20: JE/TRV20E: JE
· Abbreviation CND : Canadian model CN : Chinese model HK : Hong Kong model KR : Korea model AUS : Australian model JE : Tourist model
--3--
Table for difference of function DCRDCRModel TRV6 TRV6E US,CND, AEP, UK Destination E, HK, JE, KR DCRTRV6E E, AUS, HK, CN, JE DCRTRV20E E, AUS, HK, CN, JE Remark PAL NTSC: X101 is 66MHz (DCR-TRV20) X701 is 36MHz (DCR-TRV6/TRV11) PAL: X101 is 54MHz (DCR-TRV20E) X701 is 36MHz (DCR-TRV6E/TRV11E) PAL NTSC PAL PAL NTSC PAL DCRDCRTRV11 TRV11E US,CND, AEP, UK E, HK, JE, KR DCRTRV11E E, AUS, HK, CN, JE DCRDCRTRV20 TRV20E US,CND, AEP, UK E,HK,JE, KR
Color system
NTSC
PAL
Remote commander Lens Digital zoom 960H a a 3.5 184k a a a 3.5 246k a a a 3.5 246k 960H 960H 960H 1152H 1152H 1152H
RMT-808 RMT-809 RMT-808 RMT-811 RMT-812 RMT-811 RMT-811 RMT-811 RMT-811 10× 10× 10× 10× 10× 10× 10× 10× 10× 120× 120× 40× 40× 40× 120× 120× 120× 120× 1152H : with VC-240 board. 960H : with VC-241 board. a: with IC1406 to IC1412 of VC-240 board or with IC1402 to IC1407 of VC-241 board. a: with REC button and IC903 of VC-240/241 board.
CCD imager
960H
960H
MEMORY STICK slot DIGITAL I/O (RS232C) LINE IN LCD (size) LCD (pixel) a 2.5 200k
a 2.5 200k
2.5 200k
a a a 3.5 184k
a a a 3.5 184k
a a a 3.5 246k
LCD type 113k 113k 180k a a VC-241 CK-92 PD-123 VC-240 CK-94 PD-124 a a 180k a a 113k 113k 180k a
TYPE ST TYPE ST TYPE ST TYPE SH TYPE SH TYPE SH TYPE CA TYPE ST TYPE ST
TYPE CA, TYPE SH: with PD-123 board. TYPE ST: with PD-124 board.
--4--
113k
113k
EVF (pixel) CD-252 board FP-219 flexible
a
a
VC board
CK board
CK-94
PD board
PD-124
a: with 1152H CCD imager. a: with 960H CCD imager. VC-240: with 1152H CCD imager. VC-241: with 960H CCD imager. CK-92: with LCD TYPE CA or TYPE SH. CK-94: with LCD TYPE ST. PD-123: with LCD TYPE CA or TYPE SH. PD-124: with LCD TYPE ST.
· Abbreviation CND : Canadian model CN : Chinese model HK : Hong Kong model
KR : Korea model AUS : Australian model JE : Tourist model
TABLE OF CONTENTS SERVICE NOTE
1. 2. POWER SUPPLY DURING REPAIRS ····························· 8 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ································································ 8 "Memory Stick" Operations ···················································· 1-30 Using a "Memory Stick" introduction ······························· 1-30 Recording still images on "Memory Stick"s Memory photo recording ··················································· 1-32 Superimposing a still picture in a "Memory Stick" on a moving picture MEMORY MIX ································ 1-34 Recording an image from a mini DV tape as a still image ·· 1-35 Copying still images from a mini DV tape Photo save ······ 1-36 Viewing a still picture Memory photo playback ················ 1-36 Copying the image recorded on "Memory Stick"s to mini DV tapes ······································································ 1-37 Enlarging still images recorded on "Memory Stick"s Memory PB ZOOM ···························································· 1-38 Playing back images in a continuous loop SLIDE SHOW ··· 1-38 Preventing accidental erasure Image protection ················ 1-39 Deleting images ··································································· 1-39 Writing a print mark PRINT MARK ································· 1-40 Additional Information ···························································· 1-40 Usable cassettes ··································································· 1-40 About i.LINK ······································································· 1-41 Troubleshooting ··································································· 1-42 Self-diagnosis display ·························································· 1-43 Warning indicators and messages ········································ 1-43 Using your camcorder abroad ·············································· 1-44 Maintenance information and precautions ··························· 1-44 Quick Reference ······································································ 1-45 Identifying the parts and controls ········································ 1-45
SELF-DIAGNOSIS FUNCTION
1. 2. 3. 3-1. 3-2. 3-3. 4. SELF-DIAGNOSIS FUNCTION ······································· 9 SELF-DIAGNOSIS DISPLAY ·········································· 9 SERVICE MODE DISPLAY ············································· 9 Display Method ·································································· 9 Switching of Backup No. ··················································· 9 End of Display ···································································· 9 SELF-DIAGNOSIS CODE TABLE ································· 10
1.
GENERAL
Checking supplied accessories ·················································· 1-1 Quick Start Guide ······································································ 1-1 Getting started ··········································································· 1-2 Using this manual ·································································· 1-2 Step 1 Preparing the power supply ········································ 1-2 Installing the battery pack ···················································· 1-2 Charging the battery pack ···················································· 1-3 Connecting to the mains ······················································ 1-4 Step 2 Inserting a cassette ······················································ 1-4 Recording Basics ····································································· 1-4 Recording a picture ································································ 1-4 Shooting backlit subjects (BACK LIGHT) ·························· 1-7 Shooting in the dark (NightShot/Super NightShot) ············· 1-7 Checking the recording END SEARCH/ EDIT SEARCH/Rec Review ··············································· 1-8 Playback Basics ······································································· 1-8 Playing back a tape ································································ 1-8 Viewing the recording on TV ················································ 1-9 Advanced Recording Operations ············································· 1-10 Recording a still image on a tape Tape Photo recording ··· 1-10 Adjusting the white balance manually ································· 1-11 Using the wide mode ··························································· 1-12 Using the fader function ······················································ 1-12 Using special effects Picture effect ···································· 1-13 Using special effects Digital effect ···································· 1-14 Using the PROGRAM AE function ····································· 1-14 Adjusting the exposure manually ········································ 1-15 Focusing manually ······························································· 1-15 Advanced Playback Operations ··············································· 1-16 Playing back a tape with picture effects ······························ 1-16 Playing back a tape with digital effects ······························· 1-16 Enlaring images recorded on tapes PB ZOOM ················· 1-17 Quickly locating a scene using the zero set memory function ················································································ 1-17 Searching the boundaries of recorded tape by title Title search ········································································· 1-17 Searching a recording by date Date search ························ 1-18 Searching for a photo Photo search/Photo scan ················· 1-18 Editing ····················································································· 1-19 Dubbing a tape ····································································· 1-19 Dubbing only desired scenes Digital programme editing ···· 1-20 Using with analog video unit and PC Signal convert function ····················································· 1-23 Recording video or TV programmes ··································· 1-23 Inserting a scene from a VCR Insert editing ······················ 1-24 Audio dubbing ····································································· 1-25 Superimposing a title ··························································· 1-26 Making your own titles ························································ 1-27 Labeling a cassette ······························································· 1-28 Customizing Your Camcorder ················································· 1-28 Changing the menu settings ················································· 1-28 Resetting the date and time ·················································· 1-30
2.
DISASSEMBLY
2-1. LCD SECTION-1 (TRV6/TRV6E MODEL) (PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) ·················· 2-2 2-2. LCD SECTION-2 (TRV11/TRV11E/TRV20/TRV20E MODEL) (PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY) ········ 2-3 2-3. EVF SECTION (LB-64 BOARD) ··································· 2-4 2-4. FRONT PANEL BLOCK ASSEMBLY (MA-385 BOARD), CABINET (R) BLOCK ASSEMBLY ····························· 2-5 2-5. CK-92/94 BOARD, SPEAKER, CONTROL SWITCH BLOCK (CF30150) ····················· 2-6 2-6. DD-137 BOARD, EVF BLOCK ASSEMBLY, BT PANEL SECTION ···················································· 2-7 2-7. LENS SECTION-1 (LENS DEVICE, FP-219 FLEXIBLE BOARD) (TRV6/TRV6E/TRV11/TRV11E MODEL) ···················· 2-8 2-8. LENS SECTION-2 (LENS DEVICE, CD-252 BOARD) (TRV20/TRV20E MODEL) ············································ 2-8 2-9. VC-240/241 BOARD, MECHANISM DECK ················ 2-9 2-10. CONTROL SWITCH BLOCK (FK30150) ··················· 2-10 2-11. JK-188 BOARD, CONTROL SWITCH BLOCK (PS30150) ······································································ 2-10 2-12. MEMORY STICK CONNECTOR (TRV11/TRV11E/TRV20/TRV20E) ····························· 2-11 2-13. HINGE ASSEMBLY, LCD HARNESS PROCESSING · 2-12 2-14. CIRCUIT BOARDS LOCATION ································· 2-13 2-15. FLEXIBLE BOARDS LOCATION ······························ 2-14
3.
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV6/TRV6E) ······················································ 3-1 3-2. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV11/TRV11E) ·················································· 3-3 3-3. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV20/TRV20E) ·················································· 3-5 3-4. OVERALL BLOCK DIAGRAM (2/3) ··························· 3-7
--5--
3-5. OVERALL BLOCK DIAGRAM (3/3) ··························· 3-9 3-6. POWER BLOCK DIAGRAM (1/2) ······························ 3-11 3-7. POWER BLOCK DIAGRAM (2/2) (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 3-13 3-8. POWER BLOCK DIAGRAM (2/2) (DCR-TRV20/TRV20E) ················································ 3-15
· DD-137 (DC/DC CONVERTER)(1/2) PRINTED WIRING BOARD ····················· 4-111 4-3. WAVEFORMS ···························································· 4-113 4-4. MOUNTED LOCATION ············································ 4-125
5
1. 1-1. 5-1. 1-1.
ADJUSTMENTS
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM-1 ···························· 4-1 FRAME SCHEMATIC DIAGRAM-2 ···························· 4-3 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS ············································ 4-5 · NS-10 (SUPER NIGHTSHOT SW) PRINTED WIRING BOARD ························· 4-6 · CD-252 (CCD IMAGER) PRINTED WIRING BOARD ························· 4-7 · CD-252 (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-11 · FP-219 FLEXIBLE BOARD (CCD IMAGER) SCHEMATIC DIAGRAM ···························· 4-13 · FP-219 FLEXIBLE BOARD (CCD IMAGER) PRINTED WIRING BOARD ······················· 4-15 Shematic diagram and printed wiring board of the VC-240/241 board are not shown. Pages from 4-17 to 4-74 are not shown. · CK-92 (KEY) PRINTED WIRING BOARD ······················· 4-75 · FP-181 FLEXIBLE BOARD (PANEL REVERSE) PRINTED WIRING BOARD ······················· 4-78 · CK-94 (KEY) PRINTED WIRING BOARD ······················· 4-79 · CK-92/94 (KEY) SCHEMATIC DIAGRAM ···························· 4-83 · LB-64 (EVF BACK LIGHT) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ···························· 4-85 · JK-188 (A/V IN/OUT) PRINTED WIRING BOARD ······················· 4-87 · JK-188 (A/V IN/OUT) SCHEMATIC DIAGRAM ···························· 4-89 · CONTROL SWITCH BLOCK (FK-30150) SCHEMATIC DIAGRAM ···························· 4-91 · PD-123 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD ······················· 4-92 · PD-123 (LCD DRIVE)(1/2) SCHEMATIC DIAGRAM ···························· 4-93 · PD-123 (RGB DRIVE)(2/2) SCHEMATIC DIAGRAM ···························· 4-95 · PD-124 (LCD DRIVE)(1/2) SCHEMATIC DIAGRAM ···························· 4-97 · PD-124 (RGB DRIVE)(2/2) SCHEMATIC DIAGRAM ···························· 4-99 · PD-124 (LCD DRIVE, RGB DRIVE) PRINTED WIRING BOARD ····················· 4-101 · SE-107 (MANUAL FOCUS) PRINTED WIRING BOARD ····················· 4-102 · MA-385 (AUDIO I/O) PRINTED WIRING BOARD ····················· 4-103 · MA-385 (AUDIO I/O) SCHEMATIC DIAGRAM ·························· 4-105 · DD-137 (DC/DC CONVERTER)(1/2) SCHEMATIC DIAGRAM ·························· 4-107 · DD-137 (DC/DC CONVERTER)(2/2) SCHEMATIC DIAGRAM ·························· 4-109
Before starting adjustment ··············································· 5-1 Adjusting items when replacing main parts and boards. ··· 5-2 CAMERA SECTION ADJUSTMENT ··························· 5-6 PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) ··················································· 5-6 1-1-1. List of Service Tools ························································ 5-6 1-1-2. Preparations ····································································· 5-7 1-1-3. Precaution ········································································ 5-9 1. Setting the Switch ···························································· 5-9 2. Order of Adjustments ······················································ 5-9 3. Subjects ··········································································· 5-9 1-2. INITIALIZATION OF B, C, D, E, F, 7, 8 PAGE DATA ··· 5-10 1-2-1. INITIALIZATION OF C, D, 8 PAGE DATA ················ 5-10 1. Initializing the C, D, 8 Page Data ·································· 5-10 2. Modification of C, D, 8 Page Data ································ 5-10 3. C Page Table ·································································· 5-10 4. D Page Table ·································································· 5-12 5. 8 Page Table ··································································· 5-13 1-2-2. INITIALIZATION OF B PAGE DATA (DCR-TRV11/TRV11E/TRV20/TRV20E) ···················· 5-14 1. Initializing the B Page Data (DCR-TRV20/TRV20E) ·· 5-14 2. Modification of B Page Data (DCR-TRV20/TRV20E) ·· 5-14 3. Initializing the B Page Data (DCR-TRV11/TRV11E) ·· 5-14 4. Modification of B Page Data (DCR-TRV11/TRV11E) ·· 5-14 5. B Page Table ·································································· 5-15 1-2-3. INITIALIZATION OF E, F, 7 PAGE DATA ················· 5-15 1. Initializing the E, F, 7 Page Data ··································· 5-15 2. Modification of E, F, 7 Page Data ································· 5-15 3. F Page Table ·································································· 5-16 4. E Page Table ·································································· 5-18 5. 7 Page Table ··································································· 5-19 1-3. CAMERA SYSTEM ADJUSTMENTS ························ 5-20 1. 36MHz Origin Oscillation Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E)(VC-241 board) ·· 5-20 2. 54MHz/66MHz Origin Oscillation Adjustment (DCR-TRV20/TRV20E)(CD-252 board) ······················ 5-20 3. Zoom Key Center Adjustment ······································· 5-21 4. HALL Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-21 5. HALL Adjustment (DCR-TRV20/TRV20E) ················· 5-22 6. MR Adjustment (DCR-TRV20/TRV20E) ····················· 5-22 7. Flange Back Adjustment (Using Minipattern Box) ··············································· 5-23 8. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) ·································· 5-24 8-1. Flange Back Adjustment (1) ·········································· 5-24 8-2. Flange Back Adjustment (2) ·········································· 5-24 9. Flange Back Check ························································ 5-25 10. Optical Axis Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-26 11. Picture Frame Setting ···················································· 5-27 12. Color Reproduction Adjustment ···································· 5-28 13. MAX GAIN Adjustment ··············································· 5-29 13-1. MAX GAIN Adjustment (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-29 13-2. MAX GAIN Data Input (DCR-TRV20/TRV20E) ········· 5-29 14. Auto White Balance & LV Standard Data Input ··········· 5-29 15. Auto White Balance Adjustment ··································· 5-30 16. White Balance Check ···················································· 5-31 17. Mechanical Shutter Adjustment ···································· 5-31
--6--
17-1. Mechanical Shutter Data Input (DCR-TRV6/TRV6E/TRV11/TRV11E) ························ 5-31 17-2. Mechanical Shutter Data Input (DCR-TRV20/TRV20E) ················································ 5-32 18. Angular Velocity Sensor Sensitivity Adjustment ·········· 5-32 1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT ····························································· 5-33 1. VCO Adjustment (VC-240/241 board) ························· 5-33 2. RGB AMP Adjustment (VC-240/241 board) ················ 5-34 3. Contrast Adjustment (VC-240/241 board) ···················· 5-34 4. Backlight Consumption Current Adjustment (VC-240/241 board) ······················································ 5-35 5. White Balance Adjustment (VC-240/241 board) ·········· 5-35 1-5. LCD SYSTEM ADJUSTMENT ··································· 5-36 1-5-1. LCD SYSTEM ADJUSTMENT (DCR-TRV11/TRV11E/TRV20) ··································· 5-36 1. VCO Adjustment (PD-123 board) ································· 5-36 2. RGB AMP Adjustment (PD-123 board) ························ 5-37 3. Contrast Adjustment (PD-123 board) ···························· 5-37 4. V-COM Level Adjustment (PD-123 board) ·················· 5-38 5. V-COM Adjustment (PD-123 board) ···························· 5-38 6. White Balance Adjustment (PD-123 board) ·················· 5-39 1-5-2. LCD SYSTEM ADJUSTMENT (DCR-TRV6/TRV6E/TRV20E) ····································· 5-39 1. VCO Adjustment (PD-124 board) ································· 5-39 2. Bright Adjustment (PD-124 board) ······························· 5-40 3. Black Limit Adjustment (PD-124 board) ······················ 5-40 4. Contrast Adjustment (PD-124 board) ···························· 5-41 5. Center Level Adjustment (PD-124 board) ····················· 5-41 6. V-COM Adjustment (PD-124 board) ···························· 5-42 7. White Balance Adjustment (PD-124 board) ·················· 5-42 5-2. MECHANISM SECTION ADJUSTMENT ·················· 5-43 2-1. HOW TO ENTER RECORD MODE WITHOUT CASSETTE ··································································· 5-43 2-2. HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE ··································································· 5-43 2-3. TAPE PATH ADJUSTMENT ········································ 5-43 1. Preparation for Adjustment ··········································· 5-43 2. Procedure after operations ············································· 5-43 5-3. VIDEO SECTION ADJUSTMENTS ··························· 5-44 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············ 5-44 3-1-1. Equipment Required ······················································ 5-44 3-1-2. Precautions on Adjusting ··············································· 5-45 3-1-3. Adjusting Connectors ···················································· 5-46 3-1-4. Connecting the Equipment ············································ 5-46 3-1-5. Checking the Input Signals (Except AEP/UK model) ··· 5-46 3-1-6. Alignment Tapes ···························································· 5-47 3-1-7. Input/Output Level and Impedance ······························· 5-47 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-48 1. Initialization of B, C, D, E, F, 7, 8 Page Data ··············· 5-48 2. Serial No. Input ····························································· 5-48 2-1. Company ID Input ························································· 5-48 2-2. Serial No. Input ····························································· 5-48 3. Battery End Check (VC-240/241 board) ······················· 5-50 3-3. SERVO AND RF SYSTEM ADJUSTMENT ··············· 5-51 1. Cap FG Duty Adjustment (VC-240/241 board) ············ 5-51 2. PLL f0 & LPF f0 Adjustment (VC-240/241 board) ······· 5-51 3. Switching Position Adjustment (VC-240/241 board) ··· 5-52 4. AGC Center Level and APC & AEQ Adjustment ········· 5-52 4-1. Preparations before adjustments ···································· 5-52 4-2. AGC Center Level Adjustment (VC-240/241 board) ···· 5-52 4-3. APC & AEQ Adjustment (VC-240/241 board) ············· 5-53 4-4. Processing after Completing Adjustments ···················· 5-53 5. PLL f0 & LPF f0 Final Adjustment (VC-240/241 board) ······················································ 5-53 3-4. VIDEO SYSTEM ADJUSTMENTS ····························· 5-54 3-4-1. Base Band Block Adjustments ······································ 5-54
Chroma BPF f0 Adjustment (VC-240/241 Board) ········ 5-54 S VIDEO OUT Y Level Adjustment (VC-240/241 Board) ······················································ 5-54 3. S VIDEO OUT Chroma Level Adjustment (VC-240/241 Board) ······················································ 5-55 4. AV OUT Y, Chroma Level Check (VC-240/241 Board) ·· 5-55 3-4-2. BIST Check ··································································· 5-56 1. Playback System Check ················································ 5-56 1-1. Preparations for Playback ·············································· 5-56 1-2. IC301 TRX (RF) PB BIST Check ································· 5-56 1-3. IC301 AUD (ABUS) PB BIST Check ··························· 5-56 1-4. IC301 VFD PB BIST Check ········································· 5-56 1-5. IC301 ENCODER BIST Check ···································· 5-57 1-6. Processing after Completing Playback System Check ·· 5-58 2. Recording System Check ·············································· 5-59 2-1. Preparations for recording ············································· 5-59 2-2. IC301 TRX (RF) BIST Check ······································· 5-59 2-3. Processing after Completing Recording System Check ·· 5-59 3-5. IR TRANSMITTER ADJUSTMENTS ························· 5-60 1. IR Video Carrier Frequency Adjustment (VC-240/241 board) ······················································ 5-60 2. IR Video Deviation Adjustment (VC-240/241 board) ··· 5-60 3. IR Audio Deviation Adjustment (VC-240/241 board) ·· 5-61 3-6. AUDIO SYSTEM ADJUSTMENTS ···························· 5-62 1. Playback Level Check ··················································· 5-63 2. Overall Level Characteristics Check ····························· 5-63 3. Overall Distortion Check ··············································· 5-63 4. Overall Noise Level Check ············································ 5-63 5. Overall Separation Check ·············································· 5-63 5-4. SERVICE MODE ·························································· 5-64 4-1. ADJUSTMENT REMOTE COMMANDER ················ 5-64 1. Using the adjustment remote commander ····················· 5-64 2. Precautions upon using the adjustment remote commander ···································································· 5-64 4-2. DATA PROCESS ··························································· 5-65 4-3. SERVICE MODE ·························································· 5-66 1. Setting the Test Mode ···················································· 5-66 2. Emergence Memory Address ········································ 5-66 2-1. EMG Code (Emergency Code) ····································· 5-66 2-2. MSW Code ···································································· 5-67 3. Bit value discrimination ················································ 5-68 4. Switch check (1) ···························································· 5-68 5. Switch check (2) ···························································· 5-69 6. Record of Use check ······················································ 5-69
1. 2.
6.
REPAIR PARTS LIST
6-1-1. FRONT PANEL BLOCK ASSEMBLY AND BATTERY PANEL SECTION ········································ 6-1 6-1-2. CABINET (R) BLOCK ASSEMBLY ····························· 6-2 6-1-3. LCD BLOCK ASSEMBLY (TRV6/TRV6E MODEL) ··· 6-3 6-1-4. LCD BLOCK ASSEMBLY (TRV11/TRV11E/TRV20/TRV20E MODEL) ················ 6-4 6-1-5. CABINET (L) SECTION ················································ 6-5 6-1-6. CABINET (L) SECTION-2 ············································ 6-6 6-1-7. LENS BLOCK ASSEMBLY AND EVF BLOCK ASSEMBLY ············································· 6-7 6-1-8. CASSETTE COMPARTMENT AND DRUM BLOCK ASSEMBLY ········································· 6-8 6-1-9. LS CHASSIS ASSEMBLY ············································· 6-9 6-1-10. MECHANISM CHASSIS BLOCK ASSEMBLY ······ 6-10 6-2. ELECTRICAL PARTS LIST ········································ 6-11 Parts list of the VC-240/241 board are not shown. Pages from 6-23 to 6-44 are not shown. * Optical axis frame and color reproduction frame are shown on page 247 to 249.
--7--
SERVICE NOTE
1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1. Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the "ADJ" side. Method 2. Use the DC IN terminal. (Use the AC power adaptor (AC-L10, AC-VQ800 etc. ))
2.
1 2 3 4 5 6 7 8 9 0 qa
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
Refer to 2-4. to remove the top cabinet assembly. Refer to 2-4. to remove the front panel block assembly. Refer to 2-4. to remove the cabinet (R) block assembly. Refer to 2-6. to remove the battery panel section. Refer to 2-6. to remove the VC heat sink. (DCR-TRV20/TRV20E model only) Refer to 2-6. to remove DD-137 board. Open the VC-240/241 board. Refer to 2-9. to remove the two screws (M1.7 × 2.5) with which the MD frame assembly is fixed on the CS frame assembly. Refer to 2-9. to remove the mechanism deck and VC-240/241 board. Remove the CN006 (27P 0.3 mm) of the VC-240/241 board. Supply +4.5V from the DC power supply to the loading motor and unload with a pressing the cassette compartment.
DC power supply (+4.5Vdc)
: Unloading : Loading Disconnect from CN006 (27P) of VC-240/241 board
CN006
VC
-24
0/2
41
boa
rd
Loading motor
--8--
SELF-DIAGNOSIS FUNCTION
1. SELF-DIAGNOSIS FUNCTION 2. SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder, LCD screen or LCD window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
Viewfinder or LCD screen
C:31:11
When problems occur while the unit is operating, the counter of the viewfinder, LCD screen or LCD window consists of an alphabet and 4-digit numbers, which blinks at 3.2 Hz. This 5-character display indicates the "repaired by:", "block" in which the problem occurred, and "detailed code" of the problem.
LCD window
C : 3 1 : 11
Blinks at 3.2Hz
C
Repaired by:
31
Block
11
Detailed Code
C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer
Refer to page 10. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.
3.
3-1.
SERVICE MODE DISPLAY
Display Method
The service mode display shows up to six self-diagnosis codes shown in the past.
While pressing the "STOP" key, set the switch from OFF to "VCR or PLAYER", and continue pressing the "STOP" key for 5 seconds continuously. The service mode will be displayed, and the counter will show the backup No. and the 5-character self-diagnosis codes.
Viewfinder or LCD screen
[3] C : 3 1 : 1 1
LCD window
3 C : 3 1 : 11
Lights up
[3]
Backup No. Order of previous errors
C:31:11
Self-diagnosis Codes
Control dial
3-2.
Switching of Backup No.
By rotating the control dial, past self-diagnosis codes will be shown in order. The backup No. in the [] indicates the order in which the problem occurred. (If the number of problems which occurred is less than 6, only the number of problems which occurred will be shown.) [1] : Occurred first time [4] : Occurred fourth time [2] : Occurred second time [5] : Occurred fifth time [3] : Occurred third time [6] : Occurred the last time
3-3.
End of Display
Turning OFF the power supply will end the service mode display.
Note: The "self-diagnosis display" data will be backed up by the coin-type lithium battery of CK-92/94 board BT3201. When this coin-type lithium battery is removed, the "self-diagnosis display" data will be lost by initialization.
--9--
4.
Repaired by:
SELF-DIAGNOSIS CODE TABLE
Self-diagnosis Code Block Detailed Function Code 0 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 2 3 4 4 1 1 2 2 2 2 2 3 4 4 0 0 0 0 1 0 1 2 3 4 0 0 2 0 1 0 1 2 3 4 0 0 2 Symptom/State Correction
C C C C C C C C C C C C C C C C C C C C C C C
Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations Difficult to adjust focus (Cannot initialize focus.)
Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin 8,9 of CD-252 board or Pin qk of CN3000 of FP-219 flexible board) when focusing is performed when the control dial is rotated in the focus manual mode, and the focus motor drive circuit (IC201 of VC-240/241 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin ql,w; of CD-252 board or Pin 9 of CN3000 of FP-219 flexible board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC201 of VC-240/241 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE3051 of JK-188 board) peripheral circuits. Inspect yaw angular velocity sensor (SE3052 of JK-188 board) peripheral circuits.
E
6
1
0
0
E
6
1
1
0
Zoom operations fault (Cannot initialize zoom lens.) Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.)
E
6
2
0
0
E
6
2
0
1
-- 10 --
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 1 GENERAL
This section is extracted from instruction manual. (DCR-TRV6E/TRV11E/TRV20E model)
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
1-21
1-22
1-23
1-24
1-25
1-26
1-27
1-28
1-29
1-30
1-31
1-32
1-33
1-34
1-35
1-36
1-37
1-38
1-39
1-40
1-41
1-42
1-43
1-44
1-45
1-46
1-47
1-48E
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E SECTION 2 DISASSEMBLY
The following flow chart shows the disassembly procedure.
2-1. LCD section-1 (TRV6/TRV6E model) (PD-124 board, Inverter transformer unit, Indication LCD block assembly) 2-2. LCD section-2 (TRV11/TRV11E/TRV20/TRV20E model) (PD-123/124 board, Inverter transformer unit, Indication LCD block assembly) PD-123/124 board service position (All model)
2-3. EVF section (LB-64 board)
LB-64 board service position
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
2-4. Front panel block assembly (MA-385 board), Cabinet (R) block assembly
MA-385, CK-92/94 boards service position MA-385, CK-92/94, DD-137 boards service position
2-6. DD-137 board, EVF block assembly, BT panel section
2-7. Lens section-1 (Lens device, FP-219 flexible board) (TRV6/TRV6E/TRV11/TRV11E model) 2-8. Lens section-2 (Lens device, CD-252 board) (TRV20/TRV20E model) 2-12. Memory stick connector (TRV11/TRV11E/TRV20/TRV20E)
2-9. VC-240/241 board, Mechanism deck
2-10. Control switch block (FK30150)
2-11. JK-188 board, Control switch block (PS30150)
[Connection diagram for service position (Mainly for voltage measurement and check)] (MA-385, JK-188, CK-92/94, CD-252, FP-219 flexible, VC-240/241, DD-137 boards, Mechanism deck)
2-5. CK-92/94 board, Speaker, Control switch block (CF30150)
2-13. Hinge assembly, LCD harness processing
2-1
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD SECTION-1 (TRV6/TRV6E MODEL) (PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY)
4 P cabinet (C) assembly 1 Two screws (M1.7 × 4), lock ace, p2
REMOVING THE PD-124 BOARD, INVERTER TRANSFORMER UNIT, INDICAITON LCD BLOCK ASSEMBLY
1 Liquid crystal indicator module (24P) 6 Screw (M1.7 × 2.5)
3 Four claws 2 Two screws (M1.7 × 4), lock ace, p2
5 Two screws (M1.7 × 2.5)
D B 8 Inverter transformer unit (5P) 4 Harness (PC-118) (12P) 3 Harness (PC-119) (14P) 9 PD-124 board A 5 FP-182 flexible board (21P) qs Release the two claws, and slide the indication LCD block assembly in the direction of the arrow E. E q;Two claws qf Indication LCD block assembly qd LCD holder 9 Back light Cold cathode fluorescent tube 0 Liquid crystal indicator module D A B 6 P cabinet (M) C
P B Doa 1 r d 24
qa
P B Doa 1 rd 24
C
2 Back light (Cold cathode fluorescent tube) (15P)
7 Two tapping screws (M1.7 × 3.5)
8 P frame (13)
qa P frame assembly 7 Two claws
2-2
2-2. LCD SECTION-2 (TRV11/TRV11E/TRV20/TRV20E MODEL) (PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICATION LCD BLOCK ASSEMBLY)
4 P cabinet (C) assembly 3 Four claws 1 Two screws (M1.7 × 4), lock ace, p2
REMOVING THE PD-123/124 BOARD, INVERTER TRANSFORMER UNIT, INDICAITON LCD BLOCK ASSEMBLY
1 Liquid crystal indicator module (24P) 6 Screw (M1.7 × 2.5)
5 Two screws (M1.7 × 2.5)
2 Two screws (M1.7 × 4), lock ace, p2
D B 8 Inverter transformer unit (5P) 4 Harness (PC-118) (12P) 3 Harness (PC-119) (14P) 9 PD-123 board (TRV11/TRV11E/ TRV20 model) PD-124 board (TRV20E model) 5 FP-182 flexible board (21P) qf Indication LCD block assembly qd LCD holder E q;Two claws 7 Liquid crystal indicator module D qa P frame assembly A 7 Two claws B 6 P cabinet (M) C 8 Back light Cold cathode fluorescent tube
P B Doa rd
9
P B Doa rd
C
2 Back light (Cold cathode fluorescent tube) (15P)
A
qs Release the two claws, and slide the indication LCD block assembly in the direction of the arrow E.
[PD-123/124 BOARD SERVICE POSITION (ALL MODEL)]
AC IN AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
CN009 1 2 20
DC IN LANC jack Liquid crystal indicator module
Adjustment remote commander (RM-95)
19
CPC lid Screw (M1.7 × 4), lock ace, p2
P B Doa rd
Back light Cold cathode fluorescent tube
Indication LCD block assembly Inverter transformer unit PD-123 board (TRV11/TRV11E/TRV20 model) PD-124 board (TRV6/TRV6E/TRV20E model)
CPC-8 jig (J-6082-388-A)
2-3
2-3. EVF SECTION (LB-64 BOARD)
1 Raise the finder in the direction of the arrow A, and slide it in the direction of the arrow B. A 2 VF cabinet (upper) assembly
B
2 Two tapping screws (M1.7 × 5)
1 Press down the finder and release the two claws.
3
3 Two tapping screws (M1.7 × 5)
4 VF cabinet (lower) assembly
REMOVING THE LB-64 BOARD
9 VF lens assembly 6 LCD (16P) 7 LB-64 board 1 FP-180 flexible board (27P)
8 LCD cushion (1) 5 LCD cushion (2) 4 BL illuminator 3 LCD cushion (2) 2 Three claws
[LB-64 BOARD SERVICE POSITION]
VF lens assembly LB-64 board
AC IN
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
CPC-8 jig (J-6082-388-A)
Adjustment remote commander (RM-95) CN009 1 19 2 20
DC IN LANC jack
CPC lid Screw (M1.7 × 4), lock ace, p2
2-4
2-4. FRONT PANEL BLOCK ASSEMBLY (MA-385 BOARD), CABINET (R) BLOCK ASSEMBLY
2 Screw (M1.7 × 4), lock ace, p2 3 Claw 1 Slide the finder in the direction of the arrow A. qd Screw (M1.7 × 4), lock ace, p2 4 Top cabinet assembly A qj FP-179 flexible board (51P) qa Screw (M1.7 × 2.5), lock ace, p2 qk Cabinet (R) block assembly qs Screw (M1.7 × 2.5), lock ace, p2
5 Screw (M1.7 × 4), lock ace, p2 8 Screw (M1.7 × 4), lock ace, p2
9 FP-188 flexible qh Screw (M1.7 × 4), lock ace, p2 board (28P) qf Press the eject knob in the direction of the arrow C and open the grip cabinet.
B
Eject knob
7 Open the jack cover (DC) and jack cover (S). 6 Screw (M1.7 × 4), lock ace, p2 0 Front panel block assembly C
B
qg Screw (M1.7 × 4), lock ace, p2
Grip cabinet
REMOVING THE MICROPHONE UNIT, MA-385, SE-107 BOARD
7 SE-107 board 5 Three tapping screws (M1.7 × 3.5)
6 MA-385 board
1 Three claws 2 Tapping screw (M1.7 × 3.5) 3 Microphone retainer 4 Microphone unit
2-5
[MA-385, CK-92/94 BOARDS SERVICE POSITION]
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
AC IN
CPC-8 jig (J-6082-388-A) FP-179 flexible board (51P) Adjustment remote commander (RM-95) CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
DC IN
CN009 1 19 2 20
SE-107 board
CK oard B
MA-385 board CPC lid Screw (M1.7 × 4), lock ace, p2
JK-188 board (28P) Microphone unit Cabinet (R) block assembly
2-5. CK-92/94 BOARD, SPEAKER, CONTROL SWITCH BLOCK (CF30150)
qh Two tapping screws (M1.7 × 3.5) qg Eject knob 5 Control switch block (CF30150) (7P) 4 FP-181 flexible board (6P)
A C
Slant the bottom frame assembly, tripod insulating sheet and tripod table all three parts together, in the direction of the arrow C and remove from the cabinet (R).
qj Control switch block (CF30150)
CK Bo ar d
B
7 Four tapping screws qs Bottom frame (M1.7 × 3.5) assembly A 1 Two tapping qd Tripod insulating sheet screws (M1.7 × 3.5) B qf Tripod (large) 3 Speaker (2P) 8 Two claws
6 Harness (PC-118) (12P) 9 Harness (PC-119) (14P) qa Three screws (M1.7 ), lock ace, p2 with scotch grip.
2 Speaker retainer assembly
q; CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
2-6
2-6. DD-137 BOARD, EVF BLOCK ASSEMBLY, BT PANEL SECTION
5 Screw (M1.7 × 2.5) qs Board to board connector (80P) 1 Two screws (M1.7 × 4), lock ace, p2
B 8 CD-252 board (60P)
2 BT panel section
7 EVF block assembly
4 Raise the finder in the direction of the arrow A.
a Bo rd
B
A
VC
-
DD-137
qa Screw (M1.7 × 2.5)
6 Two tapping screws (M1.7 × 5) 3 FP-180 flexible board (27P)
qd DD-137 board
9 Two screws (M1.7 × 2.5) q; VC heat sink/VC rubber (TRV20/TRV20E model)
[MA-385, CK-92/94, DD-137 BOARDS SERVICE POSITION]
FP-180 flexible board (27P) DD-137 board
D Bo D-137 ard
EVF block assembly
BT panel block assembly
DC IN Extension cable (J-6082-395-A) (80P) CD-252 board (60P)
-B VC oar d
AC IN
AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10)
CPC-8 jig (J-6082-388-A) FP-179 flexible board (51P) CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
Adjustment remote commander (RM-95) SE-107 board
CK oard B
JK-188 board (28P) MA-385 board Microphone unit Cabinet (R) block assembly
2-7
2-7. LENS SECTION-1 (LENS DEVICE, FP-219 FLEXIBLE BOARD) (TRV6/TRV6E/TRV11/TRV11E MODEL)
8 Remove the fourteen solderings 2 Control switch block (FK30150) (8P) 1 Screw (M1.7 × 2.5) A
4 Two tapping screws (M1.7 × 5)
2 Two tapping screws (M1.7 × 3.5) 7 Seal rubber (W) A
9 CCD block assembly qa FP-219 flexible board 0 Tapping screw (M1.7 × 3.5) 6 Optical filter block 3 FP-219 flexible board (24P)
4 Lens block assembly
5 Lens device (LSV-650B)
5 DC-IN connector 1 FP-219 flexible board (50P)
3 Two tapping screws (M1.7 × 3.5)
2-8. LENS SECTION-2 (LENS DEVICE, CD-252 BOARD) (TRV20/TRV20E MODEL)
3 Two tapping screws (M1.7 × 3.5) 2 Control switch block (FK30150) (8P) 2 NS-10 board 4 Outer connector (hot shoe) 7 lens frame 1 Screw (M1.7 × 2.5) A 5 Remove the three solderings
A
6 CD shield case
REMOVING THE LENS DEVICE, CD-252 BOARD
4 Lens block assembly 1 NS-10 board
(5P)
3 Tapping screw (M1.7 × 3.5)
5 DC-IN connector
q; CD sheet 8 Remove the fourteen solderings 7 Seal rubber (W)
4 Two tapping screws (M1.7 × 5) qa CD-252 board 9 CCD block assembly 2 Flexible board (from Lens block) (27P)
1 CD-252 board (60P) 3 Two tapping screws (M1.7 × 3.5) 6 Optical filter block 5 Lens device (LSV-690A)
2-8
2-9. VC-240/241 BOARD, MECHANISM DECK
2 Control switch block (FK30150) (39P)
1 JK-188 board
(60P)
3 Two screws (M1.7 × 2.5)
VC Bo ar d
4 Mechanism deck, MD frame assembly, Cassette compartment cover 2 Two claws
REMOVING THE VC-240/241 BOARD, MECHANISM DECK
9 Two screws (M1.7 × 2.5), lock ace, p2 q; Cassette compartment cover 4 Flexible board (from drum motor) (10P) 5 Flexible board (from video head) (10P) qa Mechanism deck 2 Flexible board (from capstan motor) (27P) 3 FP-102 flexible board (27P) 8 MD frame assembly 7 Four screws (M1.4 × 1.5) B D C
4
VC
Bo
ar
d
1 Two screws (M1.7 × 2.5) D 3 VC-240 board (TRV20/TRV20E model) VC-241 board (TRV6/TRV6E/ TRV11/TRV11E model)
A
A
B
C
VC
Bo
ar
d
1 FP-179 flexible board (51P)
6 VC-240 board (TRV20/TRV20E model) VC-241 board (TRV6/TRV6E/TRV11/TRV11E model)
2-9
2-10.CONTROL SWITCH BLOCK (FK30150)
4 FP-183 flexible B A board (8P) (TRV11/TRV11E/ TRV20/TRV20E model) 5 Control switch block (PS30150) (6P) 8 Remove 9 in the direction of the arrow C while taking care not to be caught by other parts. 6 Four tapping screws (M1.7 × 3.5) 3 Zoom cover 2 Claws C 1 Screw (M1.7 × 2.5)
B A 9 Control switch block (FK30150) CS frame assembly
7 Two tapping screws (M1.7 × 3.5)
REMOVING THE CONTROL SWITCH BLOCK (FK30150), CS FRAME ASSEMBLY
4 Control switch block (FK30150)
1 Screw (M1.7 × 2.5) 3 CS frame assembly
2 Dowel
2-11.JK-188 BOARD, CONTROL SWITCH BLOCK (PS30150)
PRECAUTION DURING INSTALLATION
REMOVING THE JK-188 BOARD
2 Screw (M1.7 × 2.5) 1 Screws (M1.7 × 2.5) 3 Tapping screw (M1.7 × 3.5) 4 Control switch block (PS30150) 4 JK-188 board 3 Jack frame 2 JK-188 board, jack frame
To attach, align the switch position as shown.
1 Tapping screw (M1.7 × 3.5)
2-10
[Connection diagram for service position (Mainly for voltage measurement and check)] (MA-385, JK-188, CK-92/94, CD-252, FP-219 FLEXIBLE, VC-240/241, DD-137 BOARDS, MECHANISM DECK)
Control switch block (PS30150) (6P) EVF block assembly FP-180 flexible board (27P) DD-137 board
D Bo D-13 ard 7
BT panel section
Control switch block (FK30150) (39P) (TRV20/TRV20E model) NS-10 board CD-252 board
DC-IN connector Mechanism deck Extension cable (J-6082-395-A) (80P) AC POWER ADAPTOR (8.4Vdc) (AC-VQ800) or (AC-L10) AC IN
VC oard B
Lens block assembly
(60P)
FP-179 flexible board (51P)
CPC-8 jig (J-6082-388-A) CK-92 board (TRV11/TRV11E/TRV20 model) CK-94 board (TRV6/TRV6E/TRV20E model)
(TRV6/TRV6E/TRV11/TRV11E) Lens block assembly
CK oard B
(60P) FP-219 flexible board (50P) VC-240 board (TRV20/TRV20E model) Cabinet (R) block assembly VC-241 board (TRV6/TRV6E/TRV11/TRV11E model) (28P) JK-188 board
Adjustment remote commander (RM-95)
SE-107 board MA-385 board Microphone unit
2-12.MEMORY STICK CONNECTOR (TRV11/TRV11E/TRV20/TRV20E)
Perform the disassembling after steps 1 4 of 2-10 is complete.
5 Open it. 3 2 FP-183 flexible board Be careful not to be caught by other parts. A
4 Push it in the direction of the arrow A.
7 Remove the MS led assembly in the direction of the arrow B. qd Memory stick connector 1 Screw (M1.7 × 2.5) B q;
6 Release the two engaged portions. 9 Remove the MS chassis assembly in the direction of the arrow C.
C
qa Remove the eleven solderings. qs FP-183 flexible board 8 Tapping screw (M1.7 × 3.5)
2-11
2-13.HINGE ASSEMBLY, LCD HARNESS PROCESSING
Start repair work after removing LCD by performing steps 1 6 of 2-1 or 2-2 and remove the CK-92/94 board by performing steps 1 0 of 2-5.
2 FP-181 flexible board Be careful not to be caught by other parts. q; Hinge assembly 8 Screw (M1.7 × 2.5) 3 Two claws 4 Hinge cover (rear) 2 Screw (M1.7 × 4), lock ace, p2
5 9 FP-181 flexible board 6 Harness (PC-118) (12P) 7 Harness (PC-119) (14P) 1 Two screw (M1.7 × 4), lock ace, p2 5 Hinge cover (front)
3 Harness (PC-119) (14P) Be careful not to be caught by other parts. 4 Harness (PC-118) (12P) Be careful not to be caught by other parts.
1 Two screws (M1.7) with scotch grip
PRECAUTION DURING INSTALLATION (LCD HARNESS PROCESSING)
Be careful thet harness must not protrude from upper and lower side.
Extra length is not required in LCD. Create an extra length to allow opening and closing.
PDBoard
CKBoard
Allow extra length of this extent in the cabinet.
2-12
2-14.CIRCUIT BOARDS LOCATION
CD-252 (TRV20/TRV20E model) (CCD IMAGER) NS-10 (TRV20/TRV20E model) (SLOW SHUTTER)
LB-64 (EVF BACK LIGHT)
DD-137 (DC/DC CONVERTER)
JK-188 (AV IN/OUT)
INVERTER TRANSFORMER UNIT PD-123 (TRV11/TRV11E/TRV20), PD-124 (TRV6/TRV6E/TRV20E) (LCD DRIVE, RGB DRIVE)
VC-240 (TRV20/TRV20E model) VC-241 (TRV6/TRV6E/TRV11/TRV11E model) A/D CONV, LENS DRIVER, CAMERA CONTROL, DV SIGNAL PROCESS, REC/PB AMP, DS CONTROL, JPEG, LINE IN/OUT, IR, DRUM/CAPSTAN MOTOR DRIVE, MECHANISM CONTROL, HI CONTROL, AUDIO I/O
MA-385 (AUDIO I/O)
SE-107 (MANUAL FOCUS) CK-92 (TRV11/TRV11E/TRV20 model) CK-94 (TRV6/TRV6E/TRV20E model) (KEY)
2-13
2-15.FLEXIBLE BOARDS LOCATION
CONTROL SWITCH BLOCK (FK30150) CONTROL SWITCH BLOCK (PS30150)
FP-183 (TRV11/TRV11E/TRV20/TRV20E)
FP-181 CONTROL SWITCH BLOCK (CF30150) FP-180 FP-182 FP-228 FP-100
FP-179
(From LENS BLOCK) (TRV20/TRV20E model) FP-219 (TRV6/TRV6E/TRV11/TRV11E) (CCD IMAGER) FP-102 From TOP/END SENSOR, TAPE LED (From VIDEO HEAD)
(From DRUM MOTOR) (From CAPSTAN MOTOR)
(From LENS BLOCK) (TRV6/TRV6E/TRV11/TRV11E model)
2-14E
SECTION 3 BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV6/TRV6E)
FP-219
LENS ASSY
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
(FLEXIBLE)(1/2)
VC-241 BOARD(1/3)
J3004 DV IN/OUT
IRIS (SHUTTER)
(4-13)
(4-25)
138 139
X301 24.576MHz 45 L BUS 42
IC3000
CCD IMAGER 6 8 1-4 · 10-13
CN3001 17 17
CN701 CCD OUT 30
IC701
(GCAM3) S/H,AGC A/D CONV.
(4-31)
2 | 11 AD SO AD SCK AD0-AD9 131 | 121 (BIRDS+) CAMERA PROCESS, FOCUS/ZOOM CONTROL, EVR CLP OB V DRAIN
(4-36)
CN001 6 9 TPA+,TPB+,39 39
CN3001
IC751
199 68 | 61 213 59 | 56 70 C0-C3 C0-C3 5 1 Y0-Y7 Y0-Y7 207 203
201 205 211 215 3 7
142 145
IC361
(LIP) DV INTERFACE
(4-33)
42 42
47 48 19 CLPDM,PBLK XSHP,XSHD V DRAIN 6 6 AD CLK 23 16
IC301
(CAIN) DV SIGNAL PROCESS
51 141
TRCK LCK
47 49
29 MC BUS 37
17 HD,VD,OE HD,VD OE 21 23
112 115
71 72
152 153 156
FRRV,TRRV,TRRT
9 18 1 V1-V4,VSHT H1,H2,RG 5 9 1 21 5 22 9 25 11 11 13 13 33 12 44 45 X701 36MHz 4 5 35 37 CL 46 110 111 IR FSC AFCK(IC903) SPCK(IC751) TIMING GENERATOR
11
133 132 127
DATA TO SFD DATA FROM SFD SFD BCK
IC702
C4-C7 1 2 15 16 30 42 SPCK 13 15
99 97
REC CK REC DT
HD,VD
83 6 182 196 81 48 79 88
AD DT 6 TO OVERALL BLOCK DIAGRAM (2/3)
PB CK ATF ERR
CN3000 IRIS METER
(4-27)
49 49 48 48
(4-25)
38
M
1 2
IRIS DRIVE +,-
(4-36)
IC202 IC203
IRIS DRIVE
8 IRIS PWM I HALL AD
(SEE PAGE 3-7)
170 20 · 19 HD VD 184 · 183 MC BUS 179 FRRV,TRRV,TRRT
IC302
52 50 CHARACTER GENERATOR
(4-29)
H
6 4
IRIS HALL +,-
42 42 IRIS HALL AMP 44 44
IC801
EEPROM
4 3 2 1 3 OSD CS OSD SO OSD SCK
18 · 17 · 16 · 14
COL0 195 · | COL3 194 · 191 · 190
159 VSP SO,SI,SCK 161
75 73 71 105 · 106 67 65
PANEL G PANEL R PANEL B HD,VD EVF G EVF R EVF B 10 · 11 CN001 18 14 22 24 Y 35 50 C 31 46 V 51 47 IR V V C G G S VIDEO CN3001 Y (4-61)
FOCUS RESET SENSOR
JK-188 BOARD (2/3)
18
31 31
(4-28)
11 14 ZM A,B ZM XA,XB FC A,B FC XA,XB 139 35 35 38 38 2 4 21 23 FOCUS MOTOR DRIVE 9 12 141 142 25 25 28 28 5 7 17 19 ZOOM MOTOR DRIVE 13 16 144 ENI,DIR 1A,DIR 1B 143 ENO,DIR OA,DIR OB 140
FOCUS MOTOR
M M
63
55 59
Y C
46 7
IC1301
(TAKO) LINE OUT LINE IN AGC ACC
C
Y J3001
21 24
IC204
ZOOM MOTOR FC RST 137 SPCK (IC751) 138 AFCK 20 NIGHT SHOT CN3001 30 30 59 CN701 Y0-Y7 14 43 IRIS PWM 52 DATA FROM SFD 49 DATA TO SFD C0-C7 66 33 34 35 63-66 53 2 54 57 57 YAW AD 58 62 48 HI SO,SI SCK | 50 ZOOM AD AD SO,AD SCK EXCEPT AEP/UK MODEL CAM SO,SI,SCK 36 I HALL AD 47 38 HD,VD,OE 37 | SFD BCK 9 8 12 | A/D CONV. 34 (ALIGN) ZOOM RESET SENSOR ZM RST 9 39 39 31 · 68
(4-64)
39 48
62 63 L
IR L IR R
(4-48)
2
Y C
36 34
IC903
IC1001
(XYZ) 15 AUDIO I/O 14
6
(4-50)
VSP SO,SCK
42
54
L 49 40 V
J3003 AUDIO/VIDEO
55
R 50 36 L R L 46 37 R 45 41
R
(4-64)
51 15 16 L R 53 19 64 17 2 3 2 L R 25 23 8 10
(4-29)
MF A,B 22 23 CAMERA CONTROL X801 20MHz CN3001 18 YAW/PITCH SENSOR AMP 58 58 CN001 40 41
JK-188 BOARD(1/3)
(4-89)
SE3052 YAW SENSOR SE3051 PITCH SENSOR 8 12
IC802
IC1002
(ADC&DAC) D/A CONV. A/D CONV.
R J3002 L HEADPHONE
IC3051
SP+,-
46 49
L R
PITCH AD
59
SE-94 BOARD
CN2051 MANUAL FOCUS SENSOR 1 2 11 10 11 11 10 10
HI SO,SI,SCK
TO OVERALL BLOCK DIAGRAM (3/3) CN2001
SHOE MIC L SP+,ZOOM AD OSD CS,SO,SCK PANEL R,G,B,EVF R,G,B,HD,VD IR V,IR L,IR R
MIC L MIC R
J2001 MIC
1
35
IC2002
22 L 3 R 1 1 1 3 3 MIC AMP 14
(SEE PAGE 3-10)
3
1
LANC SIG
R L
3 33
36 5 48 5 5
(4-105)
J2002 LANC LANC SIG 26 CN2701 26 26
16
MA-385 BOARD(1/2)
3-1
3-2
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
3-2. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV11/TRV11E)
FP-219
LENS ASSY
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
(FLEXIBLE)(1/2)
VC-241 BOARD(1/3)
J3004 DV IN/OUT
IRIS (SHUTTER)
(4-13)
(4-25)
138 139
X301 24.576MHz 45 L BUS 42
IC3000
CCD IMAGER 6 8 1-4 · 10-13
CN3001 17 17
CN701 CCD OUT 30
IC701
(GCAM3) S/H,AGC A/D CONV.
(4-31)
2 | 11 AD SO AD SCK AD0-AD9 131 | 121 (BIRDS+) CAMERA PROCESS, FOCUS/ZOOM CONTROL, EVR CLP OB
(4-46)
68 | 61 59 | 56 70 HD,VD,OE 71 72 13 12 27 26 200 C0-C3 C0-C7 Y0-Y7 Y0-Y7 24 | 17 9 | 2 14 (SHIORI) DIGITAL STILL PROCESS
(4-36)
CN001 6 9 TPA+,TPB+,39 39
CN3001
IC751
IC1406
199 41 | 34 213 32 | 29 28 HD,VD OE 21 23 17 C0-C3 5 1 Y0-Y7 207 203
201 205 211 215 3 7
142 145
IC361
(LIP) DV INTERFACE
(4-33)
42 42
47 48 19 23 16
IC301
(CAIN) DV SIGNAL PROCESS
51 141
TRCK LCK
47 49
29 MC BUS 37
V DRAIN 6 6
CLPDM,PBLK XSHP,XSHD
112 115
152 153 156 133 132 127 DATA TO SFD DATA FROM SFD SFD BCK FRRV,TRRV,TRRT
V DRAIN AD CLK
202 206 212 216 4 8
58 | 51 30 42 SPCK Y0-Y7
204 208 214
18 1 V1-V4,VSHT H1,H2,RG 5 9 1 21 5 22 9 25 11 11 13 13 33
IC702
TIMING GENERATOR
1 2 15 16 12 44 45 CL 46 110 10
49 | 46 45 HD,VD,OE 44 C0-C3
2 6 18 22 24
99 97
REC CK REC DT
HD,VD
83 6
AD DT 6 TO OVERALL BLOCK DIAGRAM (2/3)
43 111 IR FSC AFCK(IC903) SPCK(IC751) X701 36MHz 4 5 35 37
182 196
88 81 PB CK ATF ERR
(4-25)
CN3000 IRIS METER 1 2 IRIS DRIVE +,49 49 48 48
38
48 79 8
(SEE PAGE 3-7)
M
IC202 IC203
IRIS DRIVE
IRIS PWM I HALL AD
170 20 · 19 HD VD 184 · 183 MC BUS 179 FRRV,TRRV,TRRT
IC302
52 50 CHARACTER GENERATOR
(4-29)
H
6 4
IRIS HALL +,-
42 42 IRIS HALL AMP 44 44
IC801
EEPROM
4 3 2
(4-27) (4-27)
19 17 7 FOCUS RESET SENSOR 5 18 31 31
(4-36)
1 3 OSD CS OSD SO OSD SCK
18 · 17 · 16 · 14
COL0 195 | · COL3 194 · 191 · 190
159 VSP SO,SI,SCK 161
75 73
PANEL G PANEL R PANEL B HD,VD EVF G EVF R EVF B 10 · 11 (4-61)
IC201
SHUTTER DRIVE
13 15
SHUTTER ON
133
71 105 · 106 67 65
JK-188 BOARD (2/3)
(4-50)
CN001 18 14 22 24 Y 35 50 C 31 46 V 51 47 IR V V C G G S VIDEO Y C 46 7
FOCUS MOTOR
M M
11 14
FC A,B FC XA,XB
139 35 35 38 38 2 4 21 23 FOCUS MOTOR DRIVE 9 12 141 ENO,DIR OA,DIR OB 140
15
AFCK (IC1903)
63
21 24
ZM A,B ZM XA,XB
55 115 59
142 25 25 28 28 5 7 17 19 ZOOM MOTOR DRIVE 13 16 144 ENI,DIR 1A,DIR 1B 143
IC1301
(TAKO) LINE OUT LINE IN AGC ACC
CN3001 Y
C
Y J3001
IC204
ZOOM MOTOR
113 112 FC RST 137 96 74 85 103 94 80 72 60 SPCK (IC751) VSP SO,SCK
(4-28)
ZOOM RESET SENSOR 9 39 39
(4-64)
39 48 42 (XYZ) 15
62 63 L
IR L IR R
ZM RST
31 · 68 34
138
IC903
(ALIGN) A/D CONV.
2 6
Y C
36 34
IC1001
14 AUDIO I/O
54
L 49 40 V
J3003 AUDIO/VIDEO
AFCK
VSP SO,SCK 20 NIGHT SHOT CN3001 30 30 59 CN701 14 43 IRIS PWM 52 DATA FROM SFD 18 I HALL AD 31 1 13 · 38 48 C0-C7 66 33 34 35 53 2 54 57 57 YAW AD 58 62 48 HI SO,SI SCK | 50 ZOOM AD AD SO,AD SCK CAM SO,SI,SCK 49 DATA TO SFD | SFD BCK 47 38 16Mbit SDRAM HD,VD,OE 37 36 9 8 12 A0-A11 D1-D10 Y0-Y7 |
55
R 50 36 L R L 46 37 R 45 41
R
(4-64)
51 15 16 L R 53 19 64 17 2 3 2 L R 25 23 8
(4-29)
MF A,B 22 23 CAMERA CONTROL X801 20MHz CN3001 18 YAW/PITCH SENSOR AMP 58 58 CN001 40 41
JK-188 BOARD(1/3)
(4-89)
SE3052 YAW SENSOR SE3051 PITCH SENSOR 8 12
IC802
IC1002
(ADC&DAC) D/A CONV. A/D CONV.
R J3002 L HEADPHONE
IC752
(4-32)
EXCEPT AEP/UK MODEL
IC3051
SP+,-
(4-48)
63-66
10
4 46 49 L R
PITCH AD
59
KASYA ON
SE-94 BOARD
CN2051 MANUAL FOCUS SENSOR 1 2 11 10 11 11 10 10
(4-45)
(4-45)
171 · 172 · 178
IC1405
HI SO,SI,SCK 16Mbit SDRAM 2 19 SP+,ZOOM AD OSD CS,SO,SCK PANEL R,G,B,EVF R,G,B,HD,VD IR V,IR L,IR R A1-A19 32 39 49 12 1 TO OVERALL BLOCK DIAGRAM (3/3) SHOE MIC L
IC1407
4Mbit FLASH 8 29 16 24 45
(4-44)
IC1404
160 (KATHMANDU) DIGITAL STILL CONTROL 57 | 79 53 194 193 192 MS DIO,MS SCLK,MS BS 161 X1401 25.8048MHz
CN2001
MIC L MIC R
J2001 MIC
1
35
IC2002
22 L 3 R 1 1 1 3 3 MIC AMP 14
(SEE PAGE 3-10)
CN008 26 24 23
CN062 5 4 2 MEMORY STICK
3
1
LANC SIG D0-D15 | 35 RXD TXD 232C ON Q1111
R L
3 33
36 5 48 5 5
(4-39)
(4-105)
J2002 LANC/ DIGITAL I/O LANC SIG/232C RD 26 LANC GND/232C TD 24 CN2701 23 23 26 26
181 175
IC1403
12 14 RS232C I/F 9 7 RXD TXD
CONTROL SWITCH BLOCK (FK-30150) (1/2)
(SEE PAGE 4-91)
MA-385 BOARD(1/2)
16
3-3
3-4
DCR-TRV6/TRV6E/TRV11/TRV11E/TRV20/TRV20E
3-3. OVERALL BLOCK DIAGRAM (1/3) (DCR-TRV20/TRV20E)
CD-252 BOARD(1/2)
LENS ASSY
( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.
IC751
(CARILLON) 138 PLL
VC-240 BOARD(1/3)
(4-11) (4-17)
(4-23)
J3004 DV IN/OUT X301 24.576MHz
IRIS (SHUTTER)
(4-11)
13 9 10 2 | 11 AD0-AD9 78 247 | | 65 238 251
SPCK1 SPCK
139
(4-36)
199 203 Y0-Y7 207 213 211 215 3 7 17 HD,VD OE 21 23 200 202 206 212 216 4 8 18 HD,VD,OE 22 24 6 6 TO OVERALL BLOCK DIAGRAM (2/3) IR FSC 182 196 81 48 79 8 88 PB CK ATF ERR 83 AD DT 99 97 REC CK REC DT 201 205 142 L BUS 145 42 (LIP) TRCK LCK DV INTERFACE 47 49 29 MC BUS 37 45
CN001 6 9 TPA+,TPB+,39 39
CN3001
IC101
CCD IMAGER 8 1-4,10-12,14 V1-V4 RG,H1,H2 40-42,44,45, 9,12,13
CCD OUT 11
IC104
5 CDS, AGC 4 1,13,14 CLPDM, XSHP,XSHD
CCD OUT(+) CCD OUT(-)
IC701
2 4 2 4 36 32 A/D CONVERTER 16 47 48
IC361
42 42
(4-33)
1 | 248 AD SO,SCK 253 | 33 HD,VD,FLD 23 23 26 26 25 25 MCK 15 15 60 61 62 57 CAMERA SIGNAL PROCESS 256 33 204 | 25 214 TIMING GENERATOR 29 30 24 X101 66MHz (TRV20) 54MHZ(TRV20E) DRAM 18 | 31 2 47 CN101 20 20 22 22 CN701 | 89 13 · 38 IRIS DRIVE +,DQ0-DQ15 | 107 | IRIS PWM 48 AFCK(IC903) SPCK(IC751) CAM SO,SI,SCK 16Mbit SDRAM 18 1 A0-A11 109 | 122 | 20 16 17 C0-C3 2 6 Y0-Y7 208 C0-C3 5
IC301
(CAIN) DV SIGNAL PROCESS
51 141
16,17,22
152 153 156 133 132 127 DATA TO SFD DATA FROM SFD SFD BCK FRRV,TRRV,TRRT
(4-11)
34 35 25
RC PROCESS
IC102
(4-17)
18 18
1
IC702
(4-19)
44 44 43 43
(SEE PAGE 3-7)
MC BUS
IRIS METER
M
12 13
IC202 IC203
IRIS DRIVE IRIS HALL AMP
(4-36)
170 20 · 19 HD VD 184 · 183
IC302
I HALL AD 42 43 45 ND HALL AD ND HALL AMP ND PWM 1 IRIS COM AFCK 3 OSD CS OSD SO OSD SCK CHARACTER GENERATOR
179
FRRV,TRRV,TRRT
H H
ND FILTER METER
17 16 25 23 27 26
IRIS HALL +,-
47 47 48 48
(4-19)
ND HALL +,-
IC205
5 19 ND FILTER DRIVE 13 ND FILTER PRE DRIVE
57 57 55 55
18 · 17 · 16 · 14
COL0 195 | · COL3 194 · 191 · 190
159 VSP SO,SI,SCK 161
M MR
ND DRIVE +,-
75 73 71 105 · 106 67
PANEL G PANEL R PANEL B HD,VD EVF G EVF R EVF B 10 · 11 CN001 18 14 22 24 Y 35 50 C 31 46 V 51 47 IR V V C G G S VIDEO CN3001 Y C Y J3001 (4-61)
59 59 60 60
8 9
F MR A,B
39 39 40 40
7 17
SHUTTER DRIVE
15
SHUTTER ON
15 14 SPCK (IC751) 223
31 · 68 34
(4-48)
JK-188 BOARD (2/3)
FOCUS MOTOR
M M
3 4
FOCUS +,-
36 36 35 35
23 2
FOCUS MOTOR DRIVE
9 10
PWMO EN0
(4-19)
33 34
IC903
(ALIGN) A/D CONV.
65 63
IC204
FOCUS/ ZOOM MOTOR CONTROL
23
SPCK1(IC751)
(4-22)
2 1
ZOON +,-
34 34 33 33
21 4
ZOOM MOTOR DRIVE
11 12
PWM1 EN1
222 | Y0-Y7
59 | 52 49 C0-C7 | 47 38 HD,VD,OE 37 36 63-66 2 6 Y C
55 59
Y C
46 7
IC1301
(TAKO) LINE OUT LINE IN AGC ACC
31 32
IC803
17 16 EVR 28
213 233 | 224
IC201
ZOOM MOTOR
(4-19)
1 46
(4-64)
39 48
62 63 L
IR L IR R
237 27 236 26 4 3 234 12 15
36 34
MR
NIGHT SHOT
IC1001
(XYZ) 15 14 AUDIO I/O
21 19
Z MR A,B
50 50 52 52
IC801
EEPROM
(4-50)
42
54
L 49 40 V
J3003 AUDIO/VIDEO
55
R 50 36 L R L 46 37 R 45 41
R
5 CN151 CN101
38 38 2 CN701
37 14 43 IRIS PWM ND PWM ND HALL AD I HALL AD
(4-64)
VSP SO,SCK DATA FROM SFD SYSCLK(IC1412) DATA TO SFD SFD BCK 9 8 12
51 15 16 L R 53 19 64 17 2 3 2 L R 25 23 8
(4-21)
MF A,B 22 23 CAMERA CONTROL
(4-21) (4-41)
20 | 35 A0-A13 165
36 143 138 | | 130 181 161 | 2 155 | 193 13 · 42 D0-D15 | 212 | 53 154 | 145 X1401 6,875MHz 77 79 54-52 19 21 2 4 A0-A10 HI SO,SI SCK JID0-JID7
46 65 66 33 34 35 53
JK-188 BOARD(1/3)
(4-89)
SE3052 YAW SENSOR SE3051 PITCH SENSOR 8 12 YAW/PITCH SENSOR AMP
IC802
IC1002
(ADC&DAC) D/A CONV. A/D CONV.
R J3002 L HEADPHONE
IC3051
18 2
X801 20MHz CN3001 58 58 CN001
40 41
IC1404
CAM SO,SI,SCK 64Mbit SDRAM AD SO,AD SCK
SP+,-
(4-40)
10 SPCK1(IC751)
54 57 57 YAW AD 58 62 48 | ZOOM AD
IC1406
EEPROM DI,CI 1 2
4 46 L R
6 49
PITCH AD
59
IC1411
SYSCLK 27 34 JID0-JID7 83
SE-94 BOARD
CN2051 MANUAL FOCUS SENSOR 1 2 11 10 11 11 10 10
50
(4-40)
(4-39)
109 112
SHUTTER SOUND
4
IC1412
DIGITAL STILL CONTROL 50 51 TXD RXD
IC1407
JPEG 2,9-16 58-64 18
IC1408
16Mbit DRAM FAST PAGE 1-13 38-48
(4-40)
41 HI SO,SI,SCK
SYSCLK(IC1412) 5-15 62-75 20-31
TO OVERALL BLOCK DIAGRAM (3/3) CN2001
SHOE MIC L SP+,ZOOM AD OSD CS,SO,SCK PANEL R,G,B,EVF R,G,B,HD,VD IR V,IR L,IR R A0-A10
(4-40)
36 | 38 10 |
28
(4-42)
(4-105)
35
MIC L MIC R
J2001 MIC
1
IC2002
22 L 3 R 1 1 1 3 3 MIC AMP 14
(SEE PAGE 3-10)
IC1409
15 | MEMORY STICK I/F 17
CN008 26 24 23
CN062 5 4 2 MEMORY STICK
3
1
LANC SIG D0-D15
1 · 48 X1402 20MHz 2 4 XTAL OSC SCK | 40
R L
3 33
36 5 48 232C ON 5 5
(4-39)
IC1410
9 RXD TXD
J2002 LANC/ DIGITAL I/O LANC SIG/232C RD 26 LANC GND/232C TD 24 CN2701 23 23 26 26
Q111