Text preview for : VP-L100_e.PDF part of Samsung VP-L100 12 files, total 129 page service manual / data for Samsung 8mm camcorder model #'s VP-L100, VP-L150, SCL100 & SCL150.
Back to : VP-L100.pdf | Home
5. Alignment and Adjustment
5-1 Mechanical Adjustment
* Note 1 : Mechanical alignment is performed for the linearity of PB-RF(Envelope). * Note 2 : Refer to the mechanism manual ÒDE-6Ó(AD68-30200A) for the mechanism alignment. Short between pin #67 of IC601 and GND in order to set the TEST MODE.(ThatÕs Track Shift Mode) Connect the Head SW Pulse in CH1 and the PB-RF in CH2 to oscilloscope. Refer to the Fig1 for the location of test point. Play the alignment tape supplied, and fit the PB-RF form like as Fig1. (Refer to the alignment manual of the DE-6 described above). 5) If the alignment is completed, then remove the short wire for the release of the test mode. 1) 2) 3) 4)
Test Point : PB RF - Pin 45 of IC201 Head Switching Trigger - Pin 96 of IC601
(PIN 96)
(PIN 67) (PIN 45)
Fig. 1 The location of test point
Samsung Electronics
5-1
Alignment and adjustment
5-2 Camera Section Adjustment
Note : 1. This system has 1) EEPROM to store the confirmed adjustment data. 2) DSP (Digital Signal Process ; ICP04 - Main board) chip to process the signal of camera parts. 3) One test point for the frequency adjustment of DSP main clock (P. CLK). 2. Keep in mind 1) Readjustment is needed when the EEPROM (ICP10 of Main board) is replaced. The reason is that EEPROM stores confirmed adjustment value of each adjustment step.
5-2-1 Preparations
1. Equipments to be used 1) DC Power supply 2) Oscilloscope 3) Frequency counter 4) Vectorscope 5) Waveform monitor 6) Color monitor or TV 7) Various charts - Color bar chart - Gray-scale chart, etc... 8) Alignment tape (Lion pattern)
2. Composition of camera P.C.Boards 1) Main PCB 3) EVF PCB 2) CCD PCB 4) LCD PCB
3. Adjustment preparations 1) Press the confirm button when each manual adjustment step is completed to write the adjustment data to the EEPROM. 2) After each adjustment step is completed, OSD shows ÒOK!Ó. 3) To cancel the adjustment mode, remove the power source.
4. Menu Board The following is a chart explaining the use of each button : Using Button TITLE (CONFIRM) C.RESET (DATA DOWN) DISPLAY (DATA UP) MENU (MODE UP) DATE (MODE DOWN) FADE (FAR ) BLC (NEAR) Adjustment Data store after finishing adjustment by DATA UP/DOWN button. When changing data value of adjust state. Mode change. Focus adjustment.
5-2
Samsung Electronics
Alignment and adjustment
The function buttons on the Menu Board are used to control the camcorder additionally, These buttons should be used for adjustment of the camera section. Menu Board for camcorder adjustment Figure of button placement when Menu Board is used for service adjustment.
Reassignment in the adjustment mode
Note : In service adjustment mode, button names are different from those in customer camera function control mode. EX) TITLE button is the same as confirm. 5. How to get into service ÒADJUSTÓ mode STEP 1 1. Connect the power source (battery/ DC cable). 2. Eject the tape if it is in the unit. 3. Set the power switch of the camcorder to ÒCAMERAÓ position. 4. Set OSD on state. STEP 2 1. PRESS ÒDSEÓ Button 3 times on the camcorder. 2. It goes to into ÒNEGAÓ mode. 3. Press and hold the ÒEJECTÓ button and ÒDISPLAYÓ button on the camcorder at the same time for more than 3 seconds. Then unit goes into service mode.
OSD STEP 3
NEGA
On screen display show "CD HALLA XX XX" CAMERA ADJUSTMENT mode has successfully been activated. Note : When ÒXX XXÓ is shown in service adjustment precedures, this indicates variable values.
Samsung Electronics
5-3
Alignment and adjustment
5. Initial data of camera parts adjustment - CAMERA AF 1st MICOM (UPD784035GC-820) DATA - NTSC During camera adjustment, the OSD displays the following abbreviations to indicate the selected mode. Example) " 00 XXXX XX XX " Note : ÒData 1Ó is previous setting in memory, ÒData 2Ó is now adjustment setting, that changes during adjustment mode. After pressing ÒTITLE (Confirm)Ó, it goes to memory.
MODE CD CE CF D0 D6 O3 O5 O7 O8 O9 OB OC 1C 1D 32 33 34 35 36 37 38 39 53 54 55 57 58 5D 5E 5F 65 66 67 71 72 73 74 75 76 77 78 82 83 88 8F 90 95 96 97
OSD HALLA IRISRA WBA LENSA Z.CHK IRIS1 P.CLK ADREF S.CLK AGC1 HAPER YSEL CWBR CWBB CRGP CRGN CHYE CHB CBGP CBGN CHGR PCBHN ECGAN ESY EWC EUSC EVSC XKCON MDSEL TGMSE HRGDL SHP.D ADDL ROUGP ROUGN CHOYE CHOB GOUGP BOUGN CHOGR CHOR AETAL AETAH AGCMA WBTAR WBTAB R-IN B-IN R-OUT
SC-L100 DATA1 DATA2 70 70 D0 D0 FF FF FF FF 80 80 70 70 40 40 OO OO 0F 0F 18 18 58 58 F8 F8 3D 3D 90 90 38 38 38 38 09 09 O8 O8 1E 1E 18 18 18 18 01 01 80 80 83 83 AE AE EE EE 00 00 00 00 01 01 02 O2 00 00 D9 D9 OO OO 36 36 2C 2C O5 O5 13 13 23 23 1B 1B 18 18 04 04 30 30 O5 O5 85 85 84 84 75 75 3C 3C 98 98 75 75
SC-L150 DATA1 70 D0 FF FF 80 70 40 OO 0F 18 58 F8 3D 90 38 38 09 O8 1E 18 18 01 80 83 AE EE 00 00 01 O2 00 D9 OO 36 2C O5 13 23 1B 18 04 30 O5 85 84 75 3C 98 75
DATA2 70 D0 FF FF 80 70 40 OO 0F 18 58 F8 3D 90 38 38 09 O8 1E 18 18 01 80 83 AE EE 00 00 01 O2 00 D9 OO 36 2C O5 13 23 1B 18 04 30 O5 85 84 75 3C 98 75
NAME OF ADJUSTMENT HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT ZOOM VR CENTER AUTO ADJUSTMENT IRIS LEVEL CONTROL-HIGH BYTE P.CLK ADJUSTMENT A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL OUTDOOR R-Y POSITIVE GAIN OUTDOOR R-Y NEGATIVE GAIN OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE) AGC MAXIMUM CONTROL WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE
5-4
Samsung Electronics
Alignment and adjustment SC-L100 DATA1 DATA2 5C 5C 20 20 FE FE O3 O3 30 30 O4 O4 OO OO 40 40 80 80 70 70 OO OO 40 40 OO OO OO OO 0F 0F 18 18 66 66 58 58 F8 F8 0B 0B A8 A8 10 10 05 05 0A 0A 1C 1C 30 30 4D 4D 76 76 B8 B8 DA DA OO OO 11 11 42 42 66 66 3D 3D 90 90 24 24 05 05 01 01 FB FB 05 05 0D 0D 1A 1A 38 38 58 58 88 88 B8 B8 DA DA 59 59 59 59 F2 F2 F2 F2 D9 D9 D9 D9 72 72 72 72 38 38 38 38 09 09 O8 O8 1E 1E SC-L150 DATA1 DATA2 5C 5C 20 20 FE FE O3 O3 30 30 O4 O4 OO OO 40 40 80 80 70 70 OO OO 40 40 OO OO OO OO 0F 0F 18 18 66 66 58 58 F8 F8 0B 0B A8 A8 10 10 05 05 0A 0A 1C 1C 30 30 4D 4D 76 76 B8 B8 DA DA OO OO 11 11 42 42 66 66 3D 3D 90 90 24 24 05 05 01 01 FB FB 05 05 0D 0D 1A 1A 38 38 58 58 88 88 B8 B8 DA DA 59 59 59 59 F2 F2 F2 F2 D9 D9 D9 D9 72 72 72 72 38 38 38 38 09 09 O8 O8 1E 1E
MODE 98 B8 B9 BB BC BD 00 01 02 03 04 O5 06 O7 O8 O9 OA OB OC 0D OE OF 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36
OSD B-OUT CFAPS APNSC CFAOR BLKST BLKMX
NAME OF ADJUSTMENT B OUTDOOR CONTROL VALUE NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE NOT USED HALL GAIN HALL REFERENCE IRIS LEVEL CONTROL-HIGH BYTE IRIS LEVEL CONTROL-L P.CLK ADJUSTMENT P.CLK PWM CONTROL-L A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL H/V BLACK NOIS THRESHOLD/GAIN HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN APERTURE SLICE CONTROL Y HI-REF. VALUE FOR C SUPRESS EDGE REF. VALUE FOR C SUPRESS Y SIGNAL GAMMA COEFF. 1 Y SIGNAL GAMMA COEFF. 2 Y SIGNAL GAMMA COEFF. 3 Y SIGNAL GAMMA COEFF. 4 Y SIGNAL GAMMA COEFF. 5 Y SIGNAL GAMMA COEFF. 6 Y SIGNAL GAMMA COEFF. 7 Y SIGNAL GAMMA COEFF. 8 Y LPF SELECTION Cr/Cb/Y LPF SELECTION C MATRIX COEF. OF Cr SIGNAL C MATRIX COEF. OF Cb SIGNAL COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL C W/B COEF. OF G SIGNAL C DARK SLICE COEF. OF Cr SIG. C DARK SLICE COEF. OF Cb SIG. C DARK SLICE COEF. OF G SIG. C SIGNAL GAMMA BENDING POINT 1 C SIGNAL GAMMA BENDING POINT 2 C SIGNAL GAMMA BENDING POINT 3 C SIGNAL GAMMA BENDING POINT 4 C SIGNAL GAMMA BENDING POINT 5 C SIGNAL GAMMA BENDING POINT 6 C SIGNAL GAMMA BENDING POINT 7 C SIGNAL GAMMA BENDING POINT 8 Cr(R-G) SIGNAL POSITIVE GAIN Cr(R-G) SIGNAL NEGATIVE GAIN Cr(B-G) SIGNAL POSITIVE GAIN Cr(B-G) SIGNAL NEGATIVE GAIN Cb(R-G) SIGNAL POSITIVE GAIN Cb(R-G) SIGNAL NEGATIVE GAIN Cb(B-G) SIGNAL POSITIVE GAIN Cb(B-G) SIGNAL NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN
Samsung Electronics
5-5
Alignment and adjustment SC-L100 DATA1 DATA2 18 18 18 18 01 01 C8 C8 28 28 35 35 50 50 3A 3A 4B 4B OO OO 30 30 7B 7B 85 85 OO OO FF FF 00 00 F0 F0 FF FF OO OO 3F 3F OO OO FF FF FF FF 3F 3F 20 20 OO OO O2 O2 A0 A0 80 80 83 83 AE AE 2C 2C EE EE 00 00 87 87 OO OO OO OO 3F 3F 00 00 01 01 02 O2 OO OO 09 09 OO OO 83 83 FF FF 00 00 D9 D9 OO OO OO OO 80 80 OO OO OO OO OO OO O1 O1 OO OO OO OO OO OO 36 36 2C 2C SC-L150 DATA1 DATA2 18 18 18 18 01 01 C8 C8 28 28 35 35 50 50 3A 3A 4B 4B OO OO 30 30 7B 7B 85 85 OO OO FF FF 00 00 F0 F0 FF FF OO OO 3F 3F OO OO FF FF FF FF 3F 3F 20 20 OO OO O2 O2 A0 A0 80 80 83 83 AE AE 2C 2C EE EE 00 00 87 87 OO OO OO OO 3F 3F 00 00 01 01 O2 O2 OO OO 09 09 OO OO 83 83 FF FF 00 00 D9 D9 OO OO OO OO 80 80 OO OO OO OO OO OO O1 O1 OO OO OO OO OO OO 36 36 2C 2C
MODE 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72
OSD
NAME OF ADJUSTMENT INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN NEGA MODE W/B B CONTROL SPOT MODE AE TARGET R DETECT WINDOW H START POINT R DETECT WINDOW H STOP POINT R DETECT WINDOW V START POINT R DETECT WINDOW V STOP POINT DSP ODM COMMEND CLIP COUNTER THRESHOULD COLOR ADJUST START VALUE R TARGET UP/DOWN OF D ZOOM B TARGET UP/DOWN OF D ZOOM SHUTTER OF D ZOOM CCD DEFECT COMPENSATION FACTOR ODM AE CLIP THRESHOULD VALUE ODM Y UPPER VALUE OF AE MODE ODM Y LOWER VALUE OF AE MODE ODM Y UPPER VALUE OF AWB MODE ODM Y LOWER VALUE OF AWB MODE R-Y THRESHOULD VALUE OF AWB MODE B-Y THRESHOULD VALUE OF AWB MODE (R-Y)+(B-Y) THRESHOULD VALUE WHITE DETECTION THRESHOLD VALUE DIGITAL CLAMP OPTICAL BLACK POINT Y DELAY CONTROL SELECTION Y SIGNAL GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL LUMINANCE BLANK LEVEL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL BURST FLAG DELAY SELECTION FSC/2FSC CONTROL DELAY CONTROL SELECTION DELAY CONTROL SELECTION SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION INVERSE NUMBER OF V ZOOM RATIO CCD V START POINT(INTEGER LINE) CCD V START POINT(SUB PIXEL) SHUTTER MODE HIGH SHUTTER SPEED CONTROL H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL RG/SHP PULSE WIDTH ADJUSTMENT D ZOOM MODE SELECTION HORIZONTAL D ZOOM STEP VERTICAL D ZOOM STEP HORIZENTAL START READ ADDRESS -H HORIZENTAL START READ ADDRESS -L HORIZONTAL D ZOOM START SUB PIXEL V D ZOOM START SUB PIXEL ODD FIELD V D ZOOM START SUB PIXEL EVEN FIELD OUTDOOR R-Y POSITIVE GAIN OUTDOOR R-Y NEGATIVE GAIN
5-6
Samsung Electronics
Alignment and adjustment SC-L100 DATA1 DATA2 O5 O5 13 13 23 23 1B 1B 18 18 04 04 48 48 20 20 78 78 60 60 88 88 20 20 4B 4B D7 D7 18 18 30 30 O5 O5 A0 A0 3A 3A 02 02 12 12 85 85 10 10 09 09 48 48 O8 O8 O8 O8 OA OA 84 84 75 75 45 45 85 65 68 3C 98 75 5C O2 83 O3 8D OO OO 6E O2 90 A6 48 00 48 30 20 05 05 0E 85 65 68 3C 98 75 5C O2 83 O3 8D OO OO 6E O2 90 A6 48 00 48 30 20 05 05 0E SC-L150 DATA1 DATA2 O5 O5 13 13 23 23 1B 1B 18 18 04 04 48 48 20 20 78 78 60 60 88 88 20 20 4B 4B D7 D7 18 18 30 30 O5 O5 A0 A0 3A 3A 02 02 12 12 85 85 10 10 09 09 48 48 O8 O8 O8 O8 OA OA 84 84 75 75 45 45 85 65 68 3C 98 75 5C O2 83 O3 8D OO OO 6E O2 90 A6 48 00 48 30 20 O5 O5 0E 85 65 68 3C 98 75 5C O2 83 O3 8D OO OO 6E O2 90 A6 48 00 48 30 20 O5 O5 0E
MODE 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 MENT 92 MENT 93 MENT 94 MENT 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA
OSD
NAME OF ADJUSTMENT OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE R VALUE OF SEPIA MODE G VALUE OF SEPIA MODE R VALUE OF YELLOW MODE G VALUE OF YELLOW MODE HALL REFERENSE START VALUE HALL GAIN START VALUE HALL MINIMUM VALUE (IRIS OPEN) HALL MAXIMUM VALUE(IRIS CLOSE) OUTDOOR DETECT IRIS CTL VALUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE) IRIS CONTROL MIN VALUE IRIS CONTROL MAX VALUE TARGET MARGEIN OF IRIS ADJUSTMENT CCD WHITE DEFFECTS ADJUSTMENT AGC MAXIMUM CONTROL NOT USED BLC ON AE TARGET CINEMA/SPOT LIGHT BLC TARGET SAND/SNOW MODE AE TARGET NEGA MODE AE TARGET NOT USED WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR START VALUE OF W/B ADJUSTB INDOOR START VALUE OF W/B ADJUSTR OUTDOOR START VALUE OF W/B ADJUSTR INDOOR START VALUE OF W/B ADJUSTR INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE B OUTDOOR CONTROL VALUE R OUTDOOR CONTROL UP/DOWN MARGIN R INDOOR CONTROL UP/DOWN MARGIN B INDOOR CONTROL UP/DOWN MARGIN B OUTDOOR CONTROL UP/DOWN MARGIN INITIAL(POWER ON) R CTL START DATA INITIAL(POWER ON) B CTL START VALUE W/B TABLE MODE W/B SD/3+AEAVR-MAXDETE W/B CONTROL BOUNDARY W/B CTL STOP HALL OF MACRO AREA W/B OUTDOOR STOP HALL R/B CTL SPEED UP/DOWN MODE CINEMA AE TAGET CINEMA / SPOT AE TAGET W/B STABLE CONDITION R CONTROL UP/DOWN OF D Z00M B CONTROL UP/DOWN OF D Z00M FOCUS RESET POSITION L
Samsung Electronics
5-7
Alignment and adjustment SC-L100 DATA1 DATA2 11 11 4B 4B 12 12 83 83 40 40 C0 C0 OO OO C0 C0 02 02 90 90 OO OO E0 E0 01 01 20 20 FE FE 30 30 O3 O3 30 30 O4 O4 A0 A0 77 77 2A 2A 28 28 24 24 A1 A1 15 15 A0 A0 12 12 O5 O5 12 12 65 65 7F 7F O6 O6 00 00 70 70 D0 D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 80 80 01 01 20 20 00 00 7E 7E O8 O8 82 82 89 89 4D 4D 00 00 AA AA 5F 5F FF FF 07 07 A8 A8 10 10 OO OO SC-L150 DATA1 DATA2 11 11 4B 4B 12 12 83 83 40 40 C0 C0 OO OO C0 C0 02 02 90 90 OO OO E0 E0 01 01 20 20 FE FE 30 30 O3 O3 30 30 O4 O4 A0 A0 77 77 2A 2A 28 28 24 24 A1 A1 15 15 A0 A0 12 12 O5 O5 12 12 65 65 BF BF O6 O6 00 00 70 70 D0 D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 80 80 01 01 20 20 00 00 7E 7E O8 O8 82 82 89 89 4D 4D 00 00 AA AA 5F 5F FF FF 07 07 A8 A8 10 10 OO OO
MODE AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6
OSD
NAME OF ADJUSTMENT FOCUS RESET POSITION H ZOOM RESET POSITION L ZOOM RESET POSITION H ZOOM RESET DIFERRENCE AF FILTER1 DATA MAGNIFY RATO FILTER1 NOISE LEVEL(L) OF AREA1 FILTER1 NOISE LEVEL(H) OF AREA1 FILTER1 NOISE LEVEL(L) OF AREA2 FILTER1 NOISE LEVEL(H) OF AREA2 FILTER2 NOISE LEVEL(L) OF AREA1 FILTER2 NOISE LEVEL(H) OF AREA1 FILTER2 NOISE LEVEL(L) OF AREA2 FILTER2 NOISE LEVEL(H) OF AREA2 NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS START AGC CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE AE TAGET OF NEGA MODE(FADE IN) H/V ADJUST OF D ZOOM HEADER COMMEND FADE LIMIT OF NEGA MODE DATA CONTROL BOUNDARY OF OUTDOOR NEGA MODE W/B R-CONTROL DATA FOCUS RETURN LOW BYTE FOCUS RETURN HIGH BYTE ZOOM RETURN LOW BYTE ZOOM RETURN HIGH BYTE LENS CHECK MARGIN (WIDE) LENS CHECK MARGIN (TELE) ADJUST MODE IRIS SETTING DATA D ZOOM RAITO AE UP/DOWN OF NEGA MODE BLC SETUP ADJUST ENABLE HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT HALL AUTO CHECK AGC AUTO CHECK LENS CHECK OF PCB LINE GYRO SENSOR CHECK (H) GYRO SENSOR CHECK (V) ZOOM VR CENTER AUTO ADJUSTMENT ZOOM/FOCUS CHECK ENABLE VR ZOOM CENTER MARGEIN COLOR GAIN ADJUSTMENT SETUP AUTO ADJUSTMENT HALL CHECK THRESHOULD COLOR ADJUST TARGET VALUE HALL ADJUST GAIN TARGET HALL ADJUST CENTER NOT USED BK NOISE TH/GAIN OF EIS H APPERTURE GAIN OF EIS #0C OF EIS ON #OD OF EIS ON #OE OF EIS ON #OF OF EIS ON #18 OF EIS ON
5-8
Samsung Electronics
Alignment and adjustment SC-L100 DATA1 DATA2 FF FF 69 69 80 80 EB EB 06 06 8C 8C 7F 7F EB EB 09 09 OO OO SC-L150 DATA1 DATA2 FF FF 69 69 80 80 EB EB 06 06 8C 8C 7F 7F EB EB 09 09 OO OO
MODE E7 E8 E9 EA EB EC ED EE EF F0
OSD
NAME OF ADJUSTMENT AGC CONTROL OF Y SINGNAL V GAIN-1(A/D GAIN) R TARGET OF W/B AUTO ADJUSTMENT V GAIN-3(CENTERING GAIN) V STOP NOISE THRESHOULD H GAIN-1(A/D GAIN) B TARGET OF W/B AUTO ADJUSTMENT H GAIN-3(CENTERING GAIN) H STOP NOISE THRESHOULD D-ZOOM STEP
6. Initial data of camera parts adjustment - CAMERA AF 2nd MICOM (UPD784035GC-828) DATA - NTSC
MODE CD CE CF D0 D6 O3 O5 O7 O8 O9 OB OC 1C 1D 32 33 34 35 36 37 38 39 53 54 55 57 58 5D 5E 5F 65 66 67 71 72 73 74 75 76 77 78 82 83
OSD HALLA IRISRA WBA LENSA Z.CHK IRIS1 P.CLK ADREF S.CLK AGC1 HAPER YSEL CWBR CWBB CRGP CRGN CHYE CHB CBGP CBGN CHGR PCBHN ECGAN ESY EWC EUSC EVSC XKCON MDSEL TGMSE HRGDL SHP.D ADDL ROUGP ROUGN CHOYE CHOB GOUGP BOUGN CHOGR CHOR AETAL AETAH
SC-L100 DATA1 DATA2 70 70 D0 D0 FF FF FF FF 80 80 70 70 40 40 OO OO 0F 0F 18 18 58 58 F8 F8 3D 3D 90 90 38 38 38 38 09 09 O8 O8 1E 1E 18 18 18 18 01 01 80 80 83 83 AE AE EE EE 00 00 00 00 01 01 02 O2 00 00 D9 D9 OO OO 36 36 2C 2C O5 O5 13 13 23 23 1B 1B 18 18 04 04 30 30 O5 O5
SC-L150 DATA1 DATA2 70 70 D0 D0 FF FF FF FF 80 80 70 70 40 40 OO OO 0F 0F 18 18 58 58 F8 F8 3D 3D 90 90 38 38 38 38 09 09 O8 O8 1E 1E 18 18 18 18 01 01 80 80 83 83 AE AE EE EE 00 00 00 00 01 01 O2 O2 00 00 D9 D9 OO OO 36 36 2C 2C O5 O5 13 13 23 23 1B 1B 18 18 04 04 30 30 O5 O5
NAME OF ADJUSTMENT HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT ZOOM VR CENTER AUTO ADJUSTMENT IRIS LEVEL CONTROL-HIGH BYTE P.CLK ADJUSTMENT A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL OUTDOOR R-Y POSITIVE GAIN OUTDOOR R-Y NEGATIVE GAIN OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE)
Samsung Electronics
5-9
Alignment and adjustment SC-L100 DATA1 DATA2 85 85 84 84 75 75 3C 3C 98 98 75 75 5C 5C 20 20 FE FE O3 O3 30 30 O4 O4 OO OO 40 40 80 80 70 70 OO OO 40 40 OO OO OO OO 0F 0F 18 18 66 66 58 58 F8 F8 0B 0B A8 A8 10 10 05 05 0A 0A 1C 1C 30 30 4D 4D 76 76 B8 B8 DA DA OO OO 11 11 42 42 66 66 3D 3D 90 90 24 24 05 05 01 01 FB FB 05 05 0D 0D 1A 1A 38 38 58 58 88 88 B8 B8 DA DA 59 59 59 59 F2 F2 F2 F2 D9 D9 D9 D9 SC-L150 DATA1 DATA2 85 85 84 84 75 75 3C 3C 98 98 75 75 5C 5C 20 20 FE FE O3 O3 30 30 O4 O4 OO OO 40 40 80 80 70 70 OO OO 40 40 OO OO OO OO 0F 0F 18 18 66 66 58 58 F8 F8 0B 0B A8 A8 10 10 05 05 0A 0A 1C 1C 30 30 4D 4D 76 76 B8 B8 DA DA OO OO 11 11 42 42 66 66 3D 3D 90 90 24 24 05 05 01 01 FB FB 05 05 0D 0D 1A 1A 38 38 58 58 88 88 B8 B8 DA DA 59 59 59 59 F2 F2 F2 F2 D9 D9 D9 D9
MODE 88 8F 90 95 96 97 98 B8 B9 BB BC BD 00 01 02 03 04 O5 06 O7 O8 O9 OA OB OC 0D OE OF 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F
OSD AGCMA WBTAR WBTAB R-IN B-IN R-OUT B-OUT CFAPS APNSC CFAOR BLKST BLKMX
NAME OF ADJUSTMENT AGC MAXIMUM CONTROL WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE B OUTDOOR CONTROL VALUE NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE NOT USED HALL GAIN HALL REFERENCE IRIS LEVEL CONTROL-HIGH BYTE IRIS LEVEL CONTROL-L P.CLK ADJUSTMENT P.CLK PWM CONTROL-L A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL H/V BLACK NOIS THRESHOLD/GAIN HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN APERTURE SLICE CONTROL Y HI-REF. VALUE FOR C SUPRESS EDGE REF. VALUE FOR C SUPRESS Y SIGNAL GAMMA COEFF. 1 Y SIGNAL GAMMA COEFF. 2 Y SIGNAL GAMMA COEFF. 3 Y SIGNAL GAMMA COEFF. 4 Y SIGNAL GAMMA COEFF. 5 Y SIGNAL GAMMA COEFF. 6 Y SIGNAL GAMMA COEFF. 7 Y SIGNAL GAMMA COEFF. 8 Y LPF SELECTION Cr/Cb/Y LPF SELECTION C MATRIX COEF. OF Cr SIGNAL C MATRIX COEF. OF Cb SIGNAL COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL C W/B COEF. OF G SIGNAL C DARK SLICE COEF. OF Cr SIG. C DARK SLICE COEF. OF Cb SIG. C DARK SLICE COEF. OF G SIG. C SIGNAL GAMMA BENDING POINT 1 C SIGNAL GAMMA BENDING POINT 2 C SIGNAL GAMMA BENDING POINT 3 C SIGNAL GAMMA BENDING POINT 4 C SIGNAL GAMMA BENDING POINT 5 C SIGNAL GAMMA BENDING POINT 6 C SIGNAL GAMMA BENDING POINT 7 C SIGNAL GAMMA BENDING POINT 8 Cr(R-G) SIGNAL POSITIVE GAIN Cr(R-G) SIGNAL NEGATIVE GAIN Cr(B-G) SIGNAL POSITIVE GAIN Cr(B-G) SIGNAL NEGATIVE GAIN Cb(R-G) SIGNAL POSITIVE GAIN Cb(R-G) SIGNAL NEGATIVE GAIN
5-10
Samsung Electronics
Alignment and adjustment SC-L100 DATA1 DATA2 72 72 72 72 38 38 38 38 09 09 O8 O8 1E 1E 18 18 18 18 01 01 C8 C8 28 28 35 35 50 50 3A 3A 4B 4B OO OO 30 30 7B 7B 85 85 OO OO FF FF 00 00 F0 F0 FF FF OO OO 3F 3F OO OO FF FF FF FF 3F 3F 01 01 OO OO O2 O2 A0 A0 80 80 83 83 AE AE 2C 2C EE EE 00 00 87 87 OO OO OO OO 3F 3F 00 00 01 01 02 O2 OO OO 09 09 OO OO 83 83 FF FF 00 00 D9 D9 OO OO OO OO 80 80 OO OO OO OO SC-L150 DATA1 DATA2 72 72 72 72 38 38 38 38 09 09 O8 O8 1E 1E 18 18 18 18 01 01 C8 C8 28 28 35 35 50 50 3A 3A 4B 4B OO OO 30 30 7B 7B 85 85 OO OO FF FF 00 00 F0 F0 FF FF OO OO 3F 3F OO OO FF FF FF FF 3F 3F 01 01 OO OO O2 O2 A0 A0 80 80 83 83 AE AE 2C 2C EE EE 00 00 87 87 OO OO OO OO 3F 3F 00 00 01 01 O2 O2 OO OO 09 09 OO OO 83 83 FF FF 00 00 D9 D9 OO OO OO OO 80 80 OO OO OO OO
MODE 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B
OSD
NAME OF ADJUSTMENT Cb(B-G) SIGNAL POSITIVE GAIN Cb(B-G) SIGNAL NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN NEGA MODE W/B B CONTROL SPOT MODE AE TARGET R DETECT WINDOW H START POINT R DETECT WINDOW H STOP POINT R DETECT WINDOW V START POINT R DETECT WINDOW V STOP POINT DSP ODM COMMEND CLIP COUNTER THRESHOULD COLOR ADJUST START VALUE R TARGET UP/DOWN OF D ZOOM B TARGET UP/DOWN OF D ZOOM SHUTTER OF D ZOOM CCD DEFECT COMPENSATION FACTOR ODM AE CLIP THRESHOULD VALUE ODM Y UPPER VALUE OF AE MODE ODM Y LOWER VALUE OF AE MODE ODM Y UPPER VALUE OF AWB MODE ODM Y LOWER VALUE OF AWB MODE R-Y THRESHOULD VALUE OF AWB MODE B-Y THRESHOULD VALUE OF AWB MODE (R-Y)+(B-Y) THRESHOULD VALUE WHITE DETECTION THRESHOLD VALUE DIGITAL CLAMP OPTICAL BLACK POINT Y DELAY CONTROL SELECTION Y SIGNAL GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL LUMINANCE BLANK LEVEL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL BURST FLAG DELAY SELECTION FSC/2FSC CONTROL DELAY CONTROL SELECTION DELAY CONTROL SELECTION SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION INVERSE NUMBER OF V ZOOM RATIO CCD V START POINT(INTEGER LINE) CCD V START POINT(SUB PIXEL) SHUTTER MODE HIGH SHUTTER SPEED CONTROL H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL RG/SHP PULSE WIDTH ADJUSTMENT D ZOOM MODE SELECTION HORIZONTAL D ZOOM STEP VERTICAL D ZOOM STEP
Samsung Electronics
5-11
Alignment and adjustment SC-L100 DATA1 DATA2 OO OO O1 O1 OO OO OO OO OO OO 36 36 2C 2C O5 O5 13 13 23 23 1B 1B 18 18 04 04 48 48 20 20 78 78 60 60 88 88 3A 3A 4B 4B D7 D7 18 18 30 30 O5 O5 A0 A0 3A 3A 02 02 12 12 85 85 10 10 09 09 48 48 O8 O8 O8 O8 OA OA 88 88 70 70 45 45 85 85 65 65 68 68 3C 3C 98 98 75 75 5C 5C O2 O2 83 83 O3 O3 8D 8D 88 88 OO OO 6E 6E O2 O2 90 90 A6 A6 48 48 8A 8A 48 48 30 30 20 20 SC-L150 DATA1 DATA2 OO OO O1 O1 OO OO OO OO OO OO 36 36 2C 2C O5 O5 13 13 23 23 1B 1B 18 18 04 04 48 48 20 20 78 78 60 60 88 88 3A 3A 4B 4B D7 D7 18 18 30 30 O5 O5 A0 A0 3A 3A 02 02 12 12 85 85 10 10 09 09 48 48 O8 O8 O8 O8 OA OA 88 88 70 70 45 45 85 85 65 65 68 68 3C 3C 98 98 75 75 5C 5C O2 O2 83 83 O3 O3 8D 8D 88 88 OO OO 6E 6E O2 O2 90 90 A6 A6 48 48 8A 8A 48 48 30 30 20 20
MODE 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7
OSD
NAME OF ADJUSTMENT HORIZENTAL START READ ADDRESS -H HORIZENTAL START READ ADDRESS -L HORIZONTAL D ZOOM START SUB PIXEL V D ZOOM START SUB PIXEL ODD FIELD V D ZOOM START SUB PIXEL EVEN FIELD OUTDOOR R-Y POSITIVE GAIN OUTDOOR R-Y NEGATIVE GAIN OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE R VALUE OF SEPIA MODE G VALUE OF SEPIA MODE R VALUE OF YELLOW MODE G VALUE OF YELLOW MODE HALL REFERENSE START VALUE HALL GAIN START VALUE HALL MINIMUM VALUE (IRIS OPEN) HALL MAXIMUM VALUE(IRIS CLOSE) OUTDOOR DETECT IRIS CTL VALUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE) IRIS CONTROL MIN VALUE IRIS CONTROL MAX VALUE TARGET MARGEIN OF IRIS ADJUSTMENT CCD WHITE DEFFECTS ADJUSTMENT AGC MAXIMUM CONTROL NOT USED BLC ON AE TARGET CINEMA/SPOT LIGHT BLC TARGET SAND/SNOW MODE AE TARGET NEGA MODE AE TARGET NOT USED WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR START VALUE OF W/B ADJUSTMENT B INDOOR START VALUE OF W/B ADJUSTMENT R OUTDOOR START VALUE OF W/B ADJUSTMENT R INDOOR START VALUE OF W/B ADJUSTMENT R INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE B OUTDOOR CONTROL VALUE R OUTDOOR CONTROL UP/DOWN MARGIN R INDOOR CONTROL UP/DOWN MARGIN B INDOOR CONTROL UP/DOWN MARGIN B OUTDOOR CONTROL UP/DOWN MARGIN INITIAL(POWER ON) R CTL START DATA INITIAL(POWER ON) B CTL START VALUE W/B TABLE MODE W/B SD/3+AEAVR-MAXDETE W/B CONTROL BOUNDARY W/B CTL STOP HALL OF MACRO AREA W/B OUTDOOR STOP HALL R OUTDOOR CONTROL UP/DOWN OF W/B ADJUST CINEMA AE TAGET CINEMA / SPOT AE TAGET W/B STABLE CONDITION
5-12
Samsung Electronics
Alignment and adjustment SC-L100 DATA1 DATA2 05 05 05 05 0E 0E 11 11 4B 4B 12 12 83 83 40 40 C0 C0 OO OO C0 C0 02 02 90 90 OO OO E0 E0 01 01 20 20 FE FE 30 30 O3 O3 30 30 O4 O4 A0 A0 77 77 2A 2A 28 28 24 24 A1 A1 15 15 A0 A0 12 12 O5 O5 12 12 65 65 7F 7F O6 O6 00 00 70 70 D0 D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 80 80 01 01 20 20 00 00 7E 7E O8 O8 82 82 89 89 4D 4D 00 00 AA AA 5F 5F FF FF 07 07 SC-L150 DATA1 DATA2 O5 O5 O5 O5 0E 0E 11 11 4B 4B 12 12 83 83 40 40 C0 C0 OO OO C0 C0 02 02 90 90 OO OO E0 E0 01 01 20 20 FE FE 30 30 O3 O3 30 30 O4 O4 A0 A0 77 77 2A 2A 28 28 24 24 A1 A1 15 15 A0 A0 12 12 O5 O5 12 12 65 65 BF BF O6 O6 00 00 70 70 D0 D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 80 80 01 01 20 20 00 00 7E 7E O8 O8 82 82 89 89 4D 4D 00 00 AA AA 5F 5F FF FF 07 07
MODE A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3
OSD
NAME OF ADJUSTMENT R CONTROL UP/DOWN OF D Z00M B CONTROL UP/DOWN OF D Z00M FOCUS RESET POSITION L FOCUS RESET POSITION H ZOOM RESET POSITION L ZOOM RESET POSITION H ZOOM RESET DIFERRENCE AF FILTER1 DATA MAGNIFY RATO FILTER1 NOISE LEVEL(L) OF AREA1 FILTER1 NOISE LEVEL(H) OF AREA1 FILTER1 NOISE LEVEL(L) OF AREA2 FILTER1 NOISE LEVEL(H) OF AREA2 FILTER2 NOISE LEVEL(L) OF AREA1 FILTER2 NOISE LEVEL(H) OF AREA1 FILTER2 NOISE LEVEL(L) OF AREA2 FILTER2 NOISE LEVEL(H) OF AREA2 NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS START AGC CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE AE TAGET OF NEGA MODE(FADE IN) H/V ADJUST OF D ZOOM HEADER COMMEND FADE LIMIT OF NEGA MODE DATA CONTROL BOUNDARY OF OUTDOOR NEGA MODE W/B R-CONTROL DATA FOCUS RETURN LOW BYTE FOCUS RETURN HIGH BYTE ZOOM RETURN LOW BYTE ZOOM RETURN HIGH BYTE LENS CHECK MARGIN (WIDE) LENS CHECK MARGIN (TELE) ADJUST MODE IRIS SETTING DATA D ZOOM RAITO AE UP/DOWN OF NEGA MODE BLC SETUP ADJUST ENABLE HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT HALL AUTO CHECK AGC AUTO CHECK LENS CHECK OF PCB LINE GYRO SENSOR CHECK (H) GYRO SENSOR CHECK (V) ZOOM VR CENTER AUTO ADJUSTMENT ZOOM/FOCUS CHECK ENABLE VR ZOOM CENTER MARGEIN COLOR GAIN ADJUSTMENT SETUP AUTO ADJUSTMENT HALL CHECK THRESHOULD COLOR ADJUST TARGET VALUE HALL ADJUST GAIN TARGET HALL ADJUST CENTER NOT USED BK NOISE TH/GAIN OF EIS H APPERTURE GAIN OF EIS #0C OF EIS ON #OD OF EIS ON
Samsung Electronics
5-13
Alignment and adjustment SC-L100 DATA1 DATA2 A8 A8 10 10 OO OO 80 80 69 69 80 80 EB EB 06 06 8C 8C 7F 7F EB EB 09 09 OO OO O1 O1 SC-L150 DATA1 DATA2 A8 A8 10 10 OO OO 80 80 69 69 80 80 EB EB 06 06 8C 8C 7F 7F EB EB 09 09 OO OO O1 O1
MODE E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1
OSD
NAME OF ADJUSTMENT #OE OF EIS ON #OF OF EIS ON #18 OF EIS ON B OUTDOOR CONTROL UP/DOWN OF W/B ADJUST V GAIN-1(A/D GAIN) R TARGET OF W/B AUTO ADJUSTMENT V GAIN-3(CENTERING GAIN) V STOP NOISE THRESHOULD H GAIN-1(A/D GAIN) B TARGET OF W/B AUTO ADJUSTMENT H GAIN-3(CENTERING GAIN) H STOP NOISE THRESHOULD D-ZOOM STEP NOT USED
7. Initial data of camera parts adjustment - CAMERA AF 1st MICOM (UPD784035GC-820) DATA - PAL
VP-L100 DATA1 DATA2 70 70 D0 D0 FF FF FF FF 80 80 70 70 40 40 OO OO 0F 0F 18 18 5A 5A FA FA 3D 3D 90 90 47 47 50 50 05 05 O8 O8 28 28 20 20 20 20 0C 0C 88 88 83 83 D0 D0 ED ED 14 14 04 04 04 04 02 O2 0E 0E DC DC OO OO 47 47 48 48 O5 O5 15 15 2C 2C 25 25 VP-L150 DATA2 70 D0 FF FF 80 70 40 OO 0F 18 5A FA 3D 90 47 50 05 O8 28 20 20 0C 88 83 D0 ED 14 04 05 O2 0E DC OO 47 48 O5 15 2C 25
MODE CD CE CF D0 D6 O3 O5 O7 O8 O9 OB OC 1C 1D 32 33 34 35 36 37 38 39 53 54 55 57 58 5D 5E 5F 65 66 67 71 72 73 74 75 76
OSD HALLA IRISRA WBA LENSA Z.CHK IRIS1 P.CLK ADREF S.CLK AGC1 HAPER YSEL CWBR CWBB CRGP CRGN CHYE CHB CBGP CBGN CHGR PCBHN ECGAN ESY EWC EUSC EVSC XKCON MDSEL TGMSE HRGDL SHP.D ADDL ROUGP ROUGN CHOYE CHOB GOUGP BOUGN
DATA1 70 D0 FF FF 80 70 40 OO 0F 18 5A FA 3D 90 47 50 05 O8 28 20 20 0C 88 83 D0 ED 14 04 05 O2 0E DC OO 47 48 O5 15 2C 25
NAME OF ADJUSTMENT HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT ZOOM VR CENTER AUTO ADJUSTMENT IRIS LEVEL CONTROL-HIGH BYTE P.CLK ADJUSTMENT A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL OUTDOOR R-Y POSITIVE GAIN OUTDOOR R-Y NEGATIVE GAIN OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN
5-14
Samsung Electronics
Alignment and adjustment VP-L100 DATA1 DATA2 20 20 0C 0C 80 80 O5 O5 85 85 86 86 74 74 3C 3C 98 98 75 75 5C 5C 20 20 FE FE O3 O3 30 30 O4 O4 OO OO 40 40 80 80 70 70 OO OO 40 40 OO OO OO OO 0F 0F 18 18 66 66 5A 5A FA FA 13 13 A8 A8 10 10 05 05 0A 0A 1C 1C 30 30 4D 4D 76 76 BA BA DA DA OO OO 11 11 42 42 66 66 3D 3D 90 90 24 24 05 05 00 00 FE FE 05 05 0D 0D 1A 1A 38 38 58 58 88 88 BA BA DA DA 59 59 59 59 VP-L150 DATA2 20 0C 80 O5 85 86 74 3C 98 75 5C 20 FE O3 30 O4 OO 40 80 70 OO 40 OO OO 0F 18 66 5A FA 13 A8 10 05 0A 1C 30 4D 76 BA DA OO 11 42 66 3D 90 24 05 00 FE 05 0D 1A 38 58 88 BA DA 59 59
MODE 77 78 82 83 88 8F 90 95 96 97 98 B8 B9 BB BC BD 00 01 02 03 04 O5 06 O7 O8 O9 OA OB OC 0D OE OF 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B
OSD CHOGR CHOR AETAL AETAH AGCMA WBTAR WBTAB R-IN B-IN R-OUT B-OUT CFAPS APNSC CFAOR BLKST BLKMX
DATA1 20 0C 80 O5 85 86 74 3C 98 75 5C 20 FE O3 30 O4 OO 40 80 70 OO 40 OO OO 0F 18 66 5A FA 13 A8 10 05 0A 1C 30 4D 76 BA DA OO 11 42 66 3D 90 24 05 00 FE 05 0D 1A 38 58 88 BA DA 59 59
NAME OF ADJUSTMENT OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE) AGC MAXIMUM CONTROL WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE B OUTDOOR CONTROL VALUE NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE NOT USED HALL GAIN HALL REFERENCE IRIS LEVEL CONTROL-HIGH BYTE IRIS LEVEL CONTROL-L P.CLK ADJUSTMENT P.CLK PWM CONTROL-L A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL H/V BLACK NOIS THRESHOLD/GAIN HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN APERTURE SLICE CONTROL Y HI-REF. VALUE FOR C SUPRESS EDGE REF. VALUE FOR C SUPRESS Y SIGNAL GAMMA COEFF. 1 Y SIGNAL GAMMA COEFF. 2 Y SIGNAL GAMMA COEFF. 3 Y SIGNAL GAMMA COEFF. 4 Y SIGNAL GAMMA COEFF. 5 Y SIGNAL GAMMA COEFF. 6 Y SIGNAL GAMMA COEFF. 7 Y SIGNAL GAMMA COEFF. 8 Y LPF SELECTION Cr/Cb/Y LPF SELECTION C MATRIX COEF. OF Cr SIGNAL C MATRIX COEF. OF Cb SIGNAL COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL C W/B COEF. OF G SIGNAL C DARK SLICE COEF. OF Cr SIG. C DARK SLICE COEF. OF Cb SIG. C DARK SLICE COEF. OF G SIG. C SIGNAL GAMMA BENDING POINT 1 C SIGNAL GAMMA BENDING POINT 2 C SIGNAL GAMMA BENDING POINT 3 C SIGNAL GAMMA BENDING POINT 4 C SIGNAL GAMMA BENDING POINT 5 C SIGNAL GAMMA BENDING POINT 6 C SIGNAL GAMMA BENDING POINT 7 C SIGNAL GAMMA BENDING POINT 8 Cr(R-G) SIGNAL POSITIVE GAIN Cr(R-G) SIGNAL NEGATIVE GAIN
Samsung Electronics
5-15
Alignment and adjustment VP-L100 DATA1 DATA2 F2 F2 F2 F2 D9 D9 D9 D9 72 72 72 72 47 47 50 50 05 05 O8 O8 28 28 20 20 20 20 0C 0C C8 C8 28 28 35 35 50 50 3A 3A 4B 4B OO OO 30 30 80 80 85 85 OO OO FF FF 00 00 F0 F0 FF FF OO OO 3F 3F OO OO FF FF FF FF 3F 3F 20 20 OO OO 01 01 A0 A0 88 88 83 83 D0 D0 2C 2C ED ED 14 14 87 87 OO OO OO OO 3F 3F 04 04 04 04 02 O2 OO OO 0C 0C OO OO 83 83 FF FF 0E 0E DC DC OO OO VP-L150 DATA2 F2 F2 D9 D9 72 72 47 50 05 O8 28 20 20 0C C8 28 35 50 3A 4B OO 30 80 85 OO FF 00 F0 FF OO 3F OO FF FF 3F 20 OO 01 A0 88 83 D0 2C ED 14 87 OO OO 3F 04 05 O2 OO 0C OO 83 FF 0E DC OO
MODE 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67
OSD
DATA1 F2 F2 D9 D9 72 72 47 50 05 O8 28 20 20 0C C8 28 35 50 3A 4B OO 30 80 85 OO FF 00 F0 FF OO 3F OO FF FF 3F 20 OO 01 A0 88 83 D0 2C ED 14 87 OO OO 3F 04 05 O2 OO 0C OO 83 FF 0E DC OO
NAME OF ADJUSTMENT Cr(B-G) SIGNAL POSITIVE GAIN Cr(B-G) SIGNAL NEGATIVE GAIN Cb(R-G) SIGNAL POSITIVE GAIN Cb(R-G) SIGNAL NEGATIVE GAIN Cb(B-G) SIGNAL POSITIVE GAIN Cb(B-G) SIGNAL NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN NEGA MODE W/B B CONTROL SPOT MODE AE TARGET R DETECT WINDOW H START POINT R DETECT WINDOW H STOP POINT R DETECT WINDOW V START POINT R DETECT WINDOW V STOP POINT DSP ODM COMMEND CLIP COUNTER THRESHOULD COLOR ADJUST START VALUE R TARGET UP/DOWN OF D ZOOM B TARGET UP/DOWN OF D ZOOM SHUTTER OF D ZOOM CCD DEFECT COMPENSATION FACTOR ODM AE CLIP THRESHOULD VALUE ODM Y UPPER VALUE OF AE MODE ODM Y LOWER VALUE OF AE MODE ODM Y UPPER VALUE OF AWB MODE ODM Y LOWER VALUE OF AWB MODE R-Y THRESHOULD VALUE OF AWB MODE B-Y THRESHOULD VALUE OF AWB MODE (R-Y)+(B-Y) THRESHOULD VALUE WHITE DETECTION THRESHOLD VALUE DIGITAL CLAMP OPTICAL BLACK POINT Y DELAY CONTROL SELECTION Y SIGNAL GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL LUMINANCE BLANK LEVEL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL BURST FLAG DELAY SELECTION FSC/2FSC CONTROL DELAY CONTROL SELECTION DELAY CONTROL SELECTION SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION INVERSE NUMBER OF V ZOOM RATIO CCD V START POINT(INTEGER LINE) CCD V START POINT(SUB PIXEL) SHUTTER MODE HIGH SHUTTER SPEED CONTROL H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL
5-16
Samsung Electronics
Alignment and adjustment VP-L100 DATA1 DATA2 OO OO 80 80 OO OO OO OO OO OO O1 O1 OO OO OO OO OO OO 47 47 48 48 O5 O5 15 15 2C 2C 25 25 20 20 0C 0C 48 48 20 20 78 78 60 60 88 88 20 20 4B 4B D7 D7 18 18 80 80 O5 O5 A0 A0 3A 3A 02 02 12 12 85 85 10 10 09 09 48 48 O8 O8 O8 O8 OA OA 86 86 74 74 45 45 85 85 65 65 68 68 3C 3C 98 98 75 75 5C 5C O2 O2 83 83 O3 O3 8D 8D OO OO OO OO 6E 6E O2 O2 90 90 A6 A6 48 48 VP-L150 DATA2 OO 80 OO OO OO O1 OO OO OO 47 48 O5 15 2C 25 20 0C 48 20 78 60 88 20 4B D7 18 80 O5 A0 3A 02 12 85 10 09 48 O8 O8 OA 86 74 45 85 65 68 3C 98 75 5C O2 83 O3 8D OO OO 6E O2 90 A6 48
MODE 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3
OSD
DATA1 OO 80 OO OO OO O1 OO OO OO 47 48 O5 15 2C 25 20 0C 48 20 78 60 88 20 4B D7 18 80 O5 A0 3A 02 12 85 10 09 48 O8 O8 OA 86 74 45 85 65 68 3C 98 75 5C O2 83 O3 8D OO OO 6E O2 90 A6 48
NAME OF ADJUSTMENT RG/SHP PULSE WIDTH ADJUSTMENT D ZOOM MODE SELECTION HORIZONTAL D ZOOM STEP VERTICAL D ZOOM STEP HORIZENTAL START READ ADDRESS -H HORIZENTAL START READ ADDRESS -L HORIZONTAL D ZOOM START SUB PIXEL V D ZOOM START SUB PIXEL ODD FIELD V D ZOOM START SUB PIXEL EVEN FIELD OUTDOOR R-Y POSITIVE GAIN OUTDOOR R-Y NEGATIVE GAIN OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE R VALUE OF SEPIA MODE G VALUE OF SEPIA MODE R VALUE OF YELLOW MODE G VALUE OF YELLOW MODE HALL REFERENSE START VALUE HALL GAIN START VALUE HALL MINIMUM VALUE (IRIS OPEN) HALL MAXIMUM VALUE(IRIS CLOSE) OUTDOOR DETECT IRIS CTL VALUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE) IRIS CONTROL MIN VALUE IRIS CONTROL MAX VALUE TARGET MARGEIN OF IRIS ADJUSTMENT CCD WHITE DEFFECTS ADJUSTMENT AGC MAXIMUM CONTROL NOT USED BLC ON AE TARGET CINEMA/SPOT LIGHT BLC TARGET SAND/SNOW MODE AE TARGET NEGA MODE AE TARGET NOT USED WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR START VALUE OF W/B ADJUSTMENT B INDOOR START VALUE OF W/B ADJUSTMENT R OUTDOOR START VALUE OF W/B ADJUSTMENT R INDOOR START VALUE OF W/B ADJUSTMENT R INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE B OUTDOOR CONTROL VALUE R OUTDOOR CONTROL UP/DOWN MARGIN R INDOOR CONTROL UP/DOWN MARGIN B INDOOR CONTROL UP/DOWN MARGIN B OUTDOOR CONTROL UP/DOWN MARGIN INITIAL(POWER ON) R CTL START DATA INITIAL(POWER ON) B CTL START VALUE W/B TABLE MODE W/B SD/3+AEAVR-MAXDETE W/B CONTROL BOUNDARY W/B CTL STOP HALL OF MACRO AREA W/B OUTDOOR STOP HALL
Samsung Electronics
5-17
Alignment and adjustment VP-L100 DATA1 DATA2 00 00 48 48 30 30 20 20 05 05 05 05 0E 0E 11 11 4B 4B 12 12 83 83 40 40 B0 B0 OO OO 00 00 03 03 80 80 OO OO 00 00 02 02 20 20 FE FE 30 30 O3 O3 30 30 O4 O4 A0 A0 66 66 2A 2A 28 28 24 24 A1 A1 15 15 A0 A0 12 12 O5 O5 12 12 65 65 7F 7F O6 O6 00 00 70 70 D0 D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 80 80 01 01 20 20 00 00 7E 7E O8 O8 82 82 89 89 4D 4D 00 00 VP-L150 DATA2 00 48 30 20 O5 O5 0E 11 4B 12 83 40 B0 OO 00 03 80 OO 00 02 20 FE 30 O3 30 O4 A0 66 2A 28 24 A1 15 A0 12 O5 12 65 7F O6 00 70 D0 FF FF FF FF FF FF FF 80 01 20 00 7E O8 82 89 4D 00
MODE A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF
OSD
DATA1 00 48 30 20 O5 O5 0E 11 4B 12 83 40 B0 OO 00 03 80 OO 00 02 20 FE 30 O3 30 O4 A0 66 2A 28 24 A1 15 A0 12 O5 12 65 7F O6 00 70 D0 FF FF FF FF FF FF FF 80 01 20 00 7E O8 82 89 4D 00
NAME OF ADJUSTMENT R/B CTL SPEED UP/DOWN MODE CINEMA AE TAGET CINEMA / SPOT AE TAGET W/B STABLE CONDITION R CONTROL UP/DOWN OF D Z00M B CONTROL UP/DOWN OF D Z00M FOCUS RESET POSITION L FOCUS RESET POSITION H ZOOM RESET POSITION L ZOOM RESET POSITION H ZOOM RESET DIFERRENCE AF FILTER1 DATA MAGNIFY RATO FILTER1 NOISE LEVEL(L) OF AREA1 FILTER1 NOISE LEVEL(H) OF AREA1 FILTER1 NOISE LEVEL(L) OF AREA2 FILTER1 NOISE LEVEL(H) OF AREA2 FILTER2 NOISE LEVEL(L) OF AREA1 FILTER2 NOISE LEVEL(H) OF AREA1 FILTER2 NOISE LEVEL(L) OF AREA2 FILTER2 NOISE LEVEL(H) OF AREA2 NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS START AGC CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE AE TAGET OF NEGA MODE(FADE IN) H/V ADJUST OF D ZOOM HEADER COMMEND FADE LIMIT OF NEGA MODE DATA CONTROL BOUNDARY OF OUTDOOR NEGA MODE W/B R-CONTROL DATA FOCUS RETURN LOW BYTE FOCUS RETURN HIGH BYTE ZOOM RETURN LOW BYTE ZOOM RETURN HIGH BYTE LENS CHECK MARGIN (WIDE) LENS CHECK MARGIN (TELE) ADJUST MODE IRIS SETTING DATA D ZOOM RAITO AE UP/DOWN OF NEGA MODE BLC SETUP ADJUST ENABLE HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT HALL AUTO CHECK AGC AUTO CHECK LENS CHECK OF PCB LINE GYRO SENSOR CHECK (H) GYRO SENSOR CHECK (V) ZOOM VR CENTER AUTO ADJUSTMENT ZOOM/FOCUS CHECK ENABLE VR ZOOM CENTER MARGEIN COLOR GAIN ADJUSTMENT SETUP AUTO ADJUSTMENT HALL CHECK THRESHOULD COLOR ADJUST TARGET VALUE HALL ADJUST GAIN TARGET HALL ADJUST CENTER NOT USED
5-18
Samsung Electronics
Alignment and adjustment VP-L100 DATA1 DATA2 AA AA 5F 5F FF FF 0B 0B A8 A8 10 10 OO OO FF FF 69 69 80 80 EB EB 06 06 8C 8C 80 80 EB EB 09 09 OO OO O1 O1 VP-L150 DATA2 AA 5F FF 0B A8 10 OO FF 69 80 EB 06 8C 80 EB 09 OO O1
MODE E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1
OSD
DATA1 AA 5F FF 0B A8 10 OO FF 69 80 EB 06 8C 80 EB 09 OO O1
NAME OF ADJUSTMENT BK NOISE TH/GAIN OF EIS H APPERTURE GAIN OF EIS #0C OF EIS ON #OD OF EIS ON #OE OF EIS ON #OF OF EIS ON #18 OF EIS ON AGC CONTROL OF Y SINGNAL V GAIN-1(A/D GAIN) R TARGET OF W/B AUTO ADJUSTMENT V GAIN-3(CENTERING GAIN) V STOP NOISE THRESHOULD H GAIN-1(A/D GAIN) B TARGET OF W/B AUTO ADJUSTMENT H GAIN-3(CENTERING GAIN) H STOP NOISE THRESHOULD D-ZOOM STEP NOT USED
8. Initial data of camera parts adjustment - CAMERA AF 2nd MICOM (UPD784035GC-828) DATA - PAL
MODE CD CE CF D0 D6 O3 O5 O7 O8 O9 OB OC 1C 1D 32 33 34 35 36 37 38 39 53 54 55 57 58 5D 5E 5F 65 66 67 71
OSD HALLA IRISRA WBA LENSA Z.CHK IRIS1 P.CLK ADREF S.CLK AGC1 HAPER YSEL CWBR CWBB CRGP CRGN CHYE CHB CBGP CBGN CHGR PCBHN ECGAN ESY EWC EUSC EVSC XKCON MDSEL TGMSE HRGDL SHP.D ADDL ROUGP
VP-L100 DATA1 DATA2 70 70 D0 D0 FF FF FF FF 80 80 70 70 40 40 OO OO 0F 0F 18 18 5A 5A FA FA 3D 3D 90 90 47 47 50 50 05 05 O8 O8 28 28 20 20 20 20 0C 0C 88 88 83 83 D0 D0 ED ED 14 14 04 04 04 04 02 O2 0E 0E DC DC OO OO 47 47
VP-L150 DATA1 DATA2 70 70 D0 D0 FF FF FF FF 80 80 70 70 40 40 OO OO 0F 0F 18 18 5A 5A FA FA 3D 3D 90 90 47 47 50 50 05 05 O8 O8 28 28 20 20 20 20 0C 0C 88 88 83 83 D0 D0 ED ED 14 14 04 04 05 05 O2 O2 0E 0E DC DC OO OO 47 47
NAME OF ADJUSTMENT HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT ZOOM VR CENTER AUTO ADJUSTMENT IRIS LEVEL CONTROL-HIGH BYTE P.CLK ADJUSTMENT A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL OUTDOOR R-Y POSITIVE GAIN
Samsung Electronics
5-19
Alignment and adjustment VP-L100 DATA1 DATA2 48 48 O5 O5 15 15 2C 2C 25 25 20 20 0C 0C 80 80 O5 O5 85 85 86 86 74 74 3C 3C 98 98 75 75 5C 5C 20 20 FE FE O3 O3 30 30 O4 O4 OO OO 40 40 80 80 70 70 OO OO 40 40 OO OO OO OO 0F 0F 18 18 66 66 5A 5A FA FA 13 13 A8 A8 10 10 05 05 0A 0A 1C 1C 30 30 4D 4D 76 76 BA BA DA DA OO OO 11 11 42 42 66 66 3D 3D 90 90 24 24 05 05 00 00 FE FE 05 05 0D 0D 1A 1A 38 38 58 58 VP-L150 DATA1 DATA2 48 48 O5 O5 15 15 2C 2C 25 25 20 20 0C 0C 80 80 O5 O5 85 85 86 86 74 74 3C 3C 98 98 75 75 5C 5C 20 20 FE FE O3 O3 30 30 O4 O4 OO OO 40 40 80 80 70 70 OO OO 40 40 OO OO OO OO 0F 0F 18 18 66 66 5A 5A FA FA 13 13 A8 A8 10 10 05 05 0A 0A 1C 1C 30 30 4D 4D 76 76 BA BA DA DA OO OO 11 11 42 42 66 66 3D 3D 90 90 24 24 05 05 00 00 FE FE 05 05 0D 0D 1A 1A 38 38 58 58
MODE 72 73 74 75 76 77 78 82 83 88 8F 90 95 96 97 98 B8 B9 BB BC BD 00 01 02 03 04 O5 06 O7 O8 O9 OA OB OC 0D OE OF 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26
OSD ROUGN CHOYE CHOB GOUGP BOUGN CHOGR CHOR AETAL AETAH AGCMA WBTAR WBTAB R-IN B-IN R-OUT B-OUT CFAPS APNSC CFAOR BLKST BLKMX
NAME OF ADJUSTMENT OUTDOOR R-Y NEGATIVE GAIN OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE) AGC MAXIMUM CONTROL WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE B OUTDOOR CONTROL VALUE NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE NOT USED HALL GAIN HALL REFERENCE IRIS LEVEL CONTROL-HIGH BYTE IRIS LEVEL CONTROL-L P.CLK ADJUSTMENT P.CLK PWM CONTROL-L A/D REFERENCE CONTROL(SETUP) SOFT CLIP CONTROL AGC CONTROL H/V BLACK NOIS THRESHOLD/GAIN HORIZONTAL APPERTURE GAIN VERTICAL APPERTURE GAIN APERTURE SLICE CONTROL Y HI-REF. VALUE FOR C SUPRESS EDGE REF. VALUE FOR C SUPRESS Y SIGNAL GAMMA COEFF. 1 Y SIGNAL GAMMA COEFF. 2 Y SIGNAL GAMMA COEFF. 3 Y SIGNAL GAMMA COEFF. 4 Y SIGNAL GAMMA COEFF. 5 Y SIGNAL GAMMA COEFF. 6 Y SIGNAL GAMMA COEFF. 7 Y SIGNAL GAMMA COEFF. 8 Y LPF SELECTION Cr/Cb/Y LPF SELECTION C MATRIX COEF. OF Cr SIGNAL C MATRIX COEF. OF Cb SIGNAL COLOR W/B COEFF. OF Cr SIGNAL COLOR W/B COEFF. OF Cb SIGNAL C W/B COEF. OF G SIGNAL C DARK SLICE COEF. OF Cr SIG. C DARK SLICE COEF. OF Cb SIG. C DARK SLICE COEF. OF G SIG. C SIGNAL GAMMA BENDING POINT 1 C SIGNAL GAMMA BENDING POINT 2 C SIGNAL GAMMA BENDING POINT 3 C SIGNAL GAMMA BENDING POINT 4 C SIGNAL GAMMA BENDING POINT 5
5-20
Samsung Electronics
Alignment and adjustment VP-L100 DATA1 DATA2 88 88 BA BA DA DA 59 59 59 59 F2 F2 F2 F2 D9 D9 D9 D9 72 72 72 72 47 47 50 50 05 05 O8 O8 28 28 20 20 20 20 0C 0C C8 C8 28 28 35 35 50 50 3A 3A 4B 4B OO OO 30 30 80 80 85 85 OO OO FF FF 00 00 F0 F0 FF FF OO OO 3F 3F OO OO FF FF FF FF 3F 3F 01 01 OO OO 01 01 A0 A0 88 88 83 83 D0 D0 2C 2C ED ED 14 14 87 87 OO OO OO OO 3F 3F 04 04 04 04 02 O2 OO OO 0C 0C OO OO VP-L150 DATA1 DATA2 88 88 BA BA DA DA 59 59 59 59 F2 F2 F2 F2 D9 D9 D9 D9 72 72 72 72 47 47 50 50 05 05 O8 O8 28 28 20 20 20 20 0C 0C C8 C8 28 28 35 35 50 50 3A 3A 4B 4B OO OO 30 30 80 80 85 85 OO OO FF FF 00 00 F0 F0 FF FF OO OO 3F 3F OO OO FF FF FF FF 3F 3F 01 01 OO OO 01 01 A0 A0 88 88 83 83 D0 D0 2C 2C ED ED 14 14 87 87 OO OO OO OO 3F 3F 04 04 05 05 O2 O2 OO OO 0C 0C OO OO
MODE 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62
OSD
NAME OF ADJUSTMENT C SIGNAL GAMMA BENDING POINT 6 C SIGNAL GAMMA BENDING POINT 7 C SIGNAL GAMMA BENDING POINT 8 Cr(R-G) SIGNAL POSITIVE GAIN Cr(R-G) SIGNAL NEGATIVE GAIN Cr(B-G) SIGNAL POSITIVE GAIN Cr(B-G) SIGNAL NEGATIVE GAIN Cb(R-G) SIGNAL POSITIVE GAIN Cb(R-G) SIGNAL NEGATIVE GAIN Cb(B-G) SIGNAL POSITIVE GAIN Cb(B-G) SIGNAL NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR R-Y POSITIVE GAIN INDOOR R-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN INDOOR B-Y POSITIVE GAIN INDOOR B-Y NEGATIVE GAIN NEGA MODE W/B B CONTROL SPOT MODE AE TARGET R DETECT WINDOW H START POINT R DETECT WINDOW H STOP POINT R DETECT WINDOW V START POINT R DETECT WINDOW V STOP POINT DSP ODM COMMEND CLIP COUNTER THRESHOULD COLOR ADJUST START VALUE R TARGET UP/DOWN OF D ZOOM B TARGET UP/DOWN OF D ZOOM SHUTTER OF D ZOOM CCD DEFECT COMPENSATION FACTOR ODM AE CLIP THRESHOULD VALUE ODM Y UPPER VALUE OF AE MODE ODM Y LOWER VALUE OF AE MODE ODM Y UPPER VALUE OF AWB MODE ODM Y LOWER VALUE OF AWB MODE R-Y THRESHOULD VALUE OF AWB MODE B-Y THRESHOULD VALUE OF AWB MODE (R-Y)+(B-Y) THRESHOULD VALUE WHITE DETECTION THRESHOLD VALUE DIGITAL CLAMP OPTICAL BLACK POINT Y DELAY CONTROL SELECTION Y SIGNAL GAIN CHROMA GAIN CONTROL Y SET-UP LEVEL CONTROL WHITE CLIP CONTROL LUMINANCE BLANK LEVEL B-Y SIGNAL BURST LEVEL CONTROL R-Y SIGNAL BURST LEVEL CONTROL BURST FLAG DELAY SELECTION FSC/2FSC CONTROL DELAY CONTROL SELECTION DELAY CONTROL SELECTION SCK CONTROL D/ZOOM MODE SELECTION TG MODE SELECTION INVERSE NUMBER OF V ZOOM RATIO CCD V START POINT(INTEGER LINE) CCD V START POINT(SUB PIXEL)
Samsung Electronics
5-21
Alignment and adjustment VP-L100 DATA1 DATA2 83 83 FF FF 0E 0E DC DC OO OO OO OO 80 80 OO OO OO OO OO OO O1 O1 OO OO OO OO OO OO 47 47 48 48 O5 O5 15 15 2C 2C 25 25 20 20 0C 0C 48 48 20 20 78 78 60 60 88 88 3A 3A 4B 4B D7 D7 18 18 80 80 O5 O5 A0 A0 3A 3A 02 02 12 12 85 85 10 10 09 09 48 48 O8 O8 O8 O8 OA OA 88 88 70 70 45 45 85 85 65 65 68 68 3C 3C 98 98 75 75 5C 5C O2 O2 83 83 O3 O3 8D 8D 88 88 OO OO VP-L150 DATA1 DATA2 83 83 FF FF 0E 0E DC DC OO OO OO OO 80 80 OO OO OO OO OO OO O1 O1 OO OO OO OO OO OO 47 47 48 48 O5 O5 15 15 2C 2C 25 25 20 20 0C 0C 48 48 20 20 78 78 60 60 88 88 3A 3A 4B 4B D7 D7 18 18 80 80 O5 O5 A0 A0 3A 3A 02 02 12 12 85 85 10 10 09 09 48 48 O8 O8 O8 O8 OA OA 88 88 70 70 45 45 85 85 65 65 68 68 3C 3C 98 98 75 75 5C 5C O2 O2 83 83 O3 O3 8D 8D 88 88 OO OO
MODE 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E
OSD
NAME OF ADJUSTMENT SHUTTER MODE HIGH SHUTTER SPEED CONTROL H1/H2/RG DELAY CONTROL SHP/SHD DELAY CONTROL SPO/FECKDELAY CONTROL RG/SHP PULSE WIDTH ADJUSTMENT D ZOOM MODE SELECTION HORIZONTAL D ZOOM STEP VERTICAL D ZOOM STEP HORIZENTAL START READ ADDRESS -H HORIZENTAL START READ ADDRESS -L HORIZONTAL D ZOOM START SUB PIXEL V D ZOOM START SUB PIXEL ODD FIELD V D ZOOM START SUB PIXEL EVEN FIELD OUTDOOR R-Y POSITIVE GAIN OUTDOOR R-Y NEGATIVE GAIN OUTDOOR R-Y POSITIVE HUE OUTDOOR R-Y NEGATIVE HUE OUTDOOR B-Y POSITIVE GAIN OUTDOOR B-Y NEGATIVE GAIN OUTDOOR B-Y POSITIVE HUE OUTDOOR B-Y NEGATIVE HUE R VALUE OF SEPIA MODE G VALUE OF SEPIA MODE R VALUE OF YELLOW MODE G VALUE OF YELLOW MODE HALL REFERENSE START VALUE HALL GAIN START VALUE HALL MINIMUM VALUE (IRIS OPEN) HALL MAXIMUM VALUE(IRIS CLOSE) OUTDOOR DETECT IRIS CTL VALUE AE TARGET (LOW BYTE) AE TARGET (HIGH BYTE) IRIS CONTROL MIN VALUE IRIS CONTROL MAX VALUE TARGET MARGEIN OF IRIS ADJUSTMENT CCD WHITE DEFFECTS ADJUSTMENT AGC MAXIMUM CONTROL NOT USED BLC ON AE TARGET CINEMA/SPOT LIGHT BLC TARGET SAND/SNOW MODE AE TARGET NEGA MODE AE TARGET NOT USED WHITE BALANCE R TARGET WHITE BALANCE B TARGET R INDOOR START VALUE OF W/B ADJUSTMENT B INDOOR START VALUE OF W/B ADJUSTMENT R OUTDOOR START VALUE OF W/B ADJUSTMENT R INDOOR START VALUE OF W/B ADJUSTMENT R INDOOR CONTROL VALUE B INDOOR CONTROL VALUE R OUTDOOR CONTROL VALUE B OUTDOOR CONTROL VALUE R OUTDOOR CONTROL UP/DOWN MARGIN R INDOOR CONTROL UP/DOWN MARGIN B INDOOR CONTROL UP/DOWN MARGIN B OUTDOOR CONTROL UP/DOWN MARGIN INITIAL(POWER ON) R CTL START DATA INITIAL(POWER ON) B CTL START VALUE
5-22
Samsung Electronics
Alignment and adjustment VP-L100 DATA1 DATA2 6E 6E O2 O2 90 90 A6 A6 48 48 8A 8A 48 48 30 30 20 20 05 05 05 05 0E 0E 11 11 4B 4B 12 12 83 83 40 40 B0 B0 OO OO 00 00 03 03 80 80 OO OO 00 00 02 02 20 20 FE FE 30 30 O3 O3 30 30 O4 O4 A0 A0 66 66 2A 2A 28 28 24 24 A1 A1 15 15 A0 A0 12 12 O5 O5 12 12 65 65 7F 7F O6 O6 00 00 70 70 D0 D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 80 80 01 01 20 20 00 00 7E 7E VP-L150 DATA1 DATA2 6E 6E O2 O2 90 90 A6 A6 48 48 8A 8A 48 48 30 30 20 20 O5 O5 O5 O5 0E 0E 11 11 4B 4B 12 12 83 83 40 40 B0 B0 OO OO 00 00 03 03 80 80 OO OO 00 00 02 02 20 20 FE FE 30 30 O3 O3 30 30 O4 O4 A0 A0 66 66 2A 2A 28 28 24 24 A1 A1 15 15 A0 A0 12 12 O5 O5 12 12 65 65 7F 7F O6 O6 00 00 70 70 D0 D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF 80 80 01 01 20 20 00 00 7E 7E
MODE 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA
OSD
NAME OF ADJUSTMENT W/B TABLE MODE W/B SD/3+AEAVR-MAXDETE W/B CONTROL BOUNDARY W/B CTL STOP HALL OF MACRO AREA W/B OUTDOOR STOP HALL R OUTDOOR CONTROL UP/DOWN OF W/B ADJUST CINEMA AE TAGET CINEMA / SPOT AE TAGET W/B STABLE CONDITION R CONTROL UP/DOWN OF D Z00M B CONTROL UP/DOWN OF D Z00M FOCUS RESET POSITION L FOCUS RESET POSITION H ZOOM RESET POSITION L ZOOM RESET POSITION H ZOOM RESET DIFERRENCE AF FILTER1 DATA MAGNIFY RATO FILTER1 NOISE LEVEL(L) OF AREA1 FILTER1 NOISE LEVEL(H) OF AREA1 FILTER1 NOISE LEVEL(L) OF AREA2 FILTER1 NOISE LEVEL(H) OF AREA2 FILTER2 NOISE LEVEL(L) OF AREA1 FILTER2 NOISE LEVEL(H) OF AREA1 FILTER2 NOISE LEVEL(L) OF AREA2 FILTER2 NOISE LEVEL(H) OF AREA2 NOISE SLICE START AGC NOISE SLICE MAXIMUM VALUE CHROMA SUPRESS START AGC CHROMA SUPRESS MAXIMUM VALUE EY BLACK START AGC EY BLACK MAXIMUM VALUE AE TAGET OF NEGA MODE(FADE IN) H/V ADJUST OF D ZOOM HEADER COMMEND FADE LIMIT OF NEGA MODE DATA CONTROL BOUNDARY OF OUTDOOR NEGA MODE W/B R-CONTROL DATA FOCUS RETURN LOW BYTE FOCUS RETURN HIGH BYTE ZOOM RETURN LOW BYTE ZOOM RETURN HIGH BYTE LENS CHECK MARGIN (WIDE) LENS CHECK MARGIN (TELE) ADJUST MODE IRIS SETTING DATA D ZOOM RAITO AE UP/DOWN OF NEGA MODE BLC SETUP ADJUST ENABLE HALL AUTO ADJUSTMENT IRIS CONTROL RANGE ADJUSTMENT WHITE BALANCE AUTO ADJUSTMENT LENS AUTO ADJUSTMENT HALL AUTO CHECK AGC AUTO CHECK LENS CHECK OF PCB LINE GYRO SENSOR CHECK (H) GYRO SENSOR CHECK (V) ZOOM VR CENTER AUTO ADJUSTMENT ZOOM/FOCUS CHECK ENABLE VR ZOOM CENTER MARGEIN COLOR GAIN ADJUSTMENT SETUP AUTO ADJUSTMENT
Samsung Electronics
5-23
Alignment and adjustment VP-L100 DATA1 DATA2 O8 O8 82 82 89 89 4D 4D 00 00 AA AA 5F 5F FF FF 0B 0B A8 A8 10 10 OO OO 80 80 69 69 80 80 EB EB 06 06 8C 8C 7F 7F EB EB 09 09 OO OO O1 O1 VP-L150 DATA1 DATA2 O8 O8 82 82 89 89 4D 4D 00 00 AA AA 5F 5F FF FF 0B 0B A8 A8 10 10 OO OO 80 80 69 69 80 80 EB EB 06 06 8C 8C 7F 7F EB EB 09 09 OO OO O1 O1
MODE DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1
OSD
NAME OF ADJUSTMENT HALL CHECK THRESHOULD COLOR ADJUST TARGET VALUE HALL ADJUST GAIN TARGET HALL ADJUST CENTER NOT USED BK NOISE TH/GAIN OF EIS H APPERTURE GAIN OF EIS #0C OF EIS ON #OD OF EIS ON #OE OF EIS ON #OF OF EIS ON #18 OF EIS ON B OUTDOOR CONTROL UP/DOWN OF W/B ADJUST V GAIN-1(A/D GAIN) R TARGET OF W/B AUTO ADJUSTMENT V GAIN-3(CENTERING GAIN) V STOP NOISE THRESHOULD H GAIN-1(A/D GAIN) B TARGET OF W/B AUTO ADJUSTMENT H GAIN-3(CENTERING GAIN) H STOP NOISE THRESHOULD D-ZOOM STEP NOT USED
Note : On table you see the ÒXX XXÓ for DATA 1/DATA 2 ÒXX XXÓ means arbitrary value. CD
HALLA XX Data in memory XX Data to be adjusted
5-24
Samsung Electronics
Alignment and adjustment
5-2-2 Camera System Adjustment
Note : From now on, the structure of every adjustment is as follows. Step Adjustment Item 1) Mode and input signal/ alignment tape 2) Test point and ADJ. part 3) And after Result and Remarks Note : The on-screen display information. ÒXX XXÓ means arbitrary value. It can be different number depend on the conditions. CD HALLA XX XX
1. Focus to zoom tracking Note : To maintain proper focus throughout the zoom range, the focus lens position must be changed as the zoom lens is moved. During this adjustment the microprocessor will measure the focus positioning requirements at the wide and telephoto position of the zoom lens. 1) Camera ÒE-EÓ. 2) Focus chart (Attached on the last page of this manual). 3) Aim the camera at the focus chart placed about 30ft. (8 to 10 meters) away and perpendicular to the center of the lens. The chart should be placed on the flat, gray or white wall. 4) Connect monitor TV jack to video output jack. 5) Press the ÒMENU(MODE UP)Ó and ÒDATE (MODE DOWN)Ó button, so that the OSD start is ÒDO LENSA XX XXÓ. 6) Focus adjustment a. Full auto : Press ÒTITLE (CONFIRM)Ó button for full auto adjustment. The camera will move both zoom and focus lens. The adjustment is finished when the O.K! message appears on the TV screen.
8M~10M(About 30ft) (Be sure to maintain the distance.)
LENS
CCD
Samsung Electronics
5-25
Alignment and adjustment
2. P. CLK Adjustment 1) ÒCameraÓ, no signal input. 2) P.CLK and AF MICOM. 3) Connent a frequency counter to P.CLK. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò05 P.CLK XX XXÓ. 5) Adjust the Ò DISPLAY (DATA UP)/ C.RESET (DATA DOWN)Ó button so that frequency is NTSC : SCL100/SCL150 --> 9.534964MHz ± 50Hz. PAL : VP-L100/VP-L150 --> 9.453125MHz ± 50Hz.
3. Zoom VR Center 1) Camera ÒE-EÓ, 3100¡K gray-scale chart. 2) Video(output) jack and EVR. 3) Connect monitor TV to video(output) jack. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is ÒD6 Z, CHK XX XXÓ. 5) Press ÒTITLE (CONFIRM)Ó button. 6) Then, the microprocessor will work ; - Find the Zoom VR Centerposition - Store the data to mode D6.
4. Auto hall 1) Camera ÒE-EÓ, 3100¡K gray-scale chart. 2) Video(output) jack and EVR. 3) Connect monitor TV to video(output) jack. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is ÒCD HALLA XX XXÓ. 5) Press ÒTITLE (CONFIRM)Ó button. 6) Then, the microprocessor will work ; - IRIS open, HALL maximum value found, - IRIS closed, HALL minimum value found, - IRIS open, HALL maximum value found, - Store the data to mode 02 and mode 01. - Store the HALL min./max. data to mode 7F and mode 80.
5-26
Samsung Electronics
Alignment and adjustment
5. AUTO IRIS 1) Camera ÒE-EÓ, 3100¡K gray-scale chart. 2) Video(output) jack and AF MICOM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is ÒCE IRISA XX XXÓ. 5) Press ÒTITLE(confirm)Ó Button. 6) Then, the micro process will work; - IRIS open, IRIS control minimum Value found. - IRIS close, IRIS control minimum Value found. - Store the data to mode 84 and mode 85. 7) The OSD shows ÒO.KÓ.
6. Auto white balance 1) Camera ÒE-EÓ, 3100¡K/5100¡K gray-scale chart. 2) Video(output) jack and AF MICOM. 4) Connect vectorscope input jack to video(output) jack. 3) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is ÒCF WBA XX XXÓ. a. W/B Indoor a-1. Aim the camera at a 3100¡K gray-scale chart illuminated at 1500 to 2000 lx. (40us) a-2. Press ÒTITLE (CONFIRM)Ó button so that the white vector moves to the center on screen of the vectorscope. a-3. The OSD shows ÒOK!Ó. b. W/B Outdoor b-1. Aim the camera at a 5100¡K gray-scale chart illuminated at 1500 to 2000 lx. (40us) b-2. Press ÒTITLE (CONFIRM)Ó button so that the white vector moves to the center on screen of the vectorscope. b-3. The OSD shows ÒOK!Ó.
Match the white luminance point with the black luminance point
Center of white level
H
100IRE
Optical black level
40US
7. Pre white balance (I) 1) Camera ÒE-EÓ, 3100¡K gray-scale chart. 2) Video(output) jack and AF MICOM. 3) Connect vectorscope input jack to video(output) jack. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò1C CWBR XX XXÓ. 5) Aim the camera at a 3100¡K gray-scale chart illuminated at 1500 to 2000 lx. 6) Adjust the Ò DISPLAY (DATA UP)/ C.RESET (DATA DOWN)Ó button so that the white vector moves to the B-Y axial on screen of the vectorscope. 7) The OSD shows ÒOK!Ó.
Match the white luminance point with the black luminance point
Samsung Electronics
5-27
Alignment and adjustment
8. Pre white balance (II) 1) Camera ÒE-EÓ, 3100¡K gray-scale chart. 2) Video(output) jack and AF MICOM. 4) Connect vectorscope input jack to video(output) jack. 3) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò1D CWBB XX XXÓ. 5) Aim the camera at a 3100¡K gray-scale chart illuminated at 1500 to 2000 lx. 6) Adjust the Ò DISPLAY (DATA UP)/ C.RESET (DATA DOWN)Ó button so that the white vector moves to the R-Y axial on screen of the vectorscope. 7) The OSD shows ÒOK!Ó.
Match the white luminance point with the black luminance point
10. R-Y Negative Gain 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò33 CRGN XX XXÓ. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the Ò DISPLAY (DATA UP) /C.RESET(DATA DOWN)Ó button so that the cyan level is 65IRE. 7) Be sure to press the ÒTITLE (CONFIRM)Ó button to memorize setting. 8) The OSD shows ÒOK!Ó.
65IRE
9. R-Y Positive Gain 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò32 CRGP XX XXÓ. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the Ò DISPLAY (DATA UP)/C.RESET(DATA DOWN)Ó button so that the red level is 70IRE. 7) Be sure to press the ÒTITLE (CONFIRM)Ó button to memorize setting. 8) The OSD shows ÒOK!Ó.
11. B-Y Positive Gain 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò36 CBGP XX XXÓ. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the Ò DISPLAY (DATA UP)/C.RESET (DATA DOWN)Ó button so that the blue level is 50IRE. 7) Be sure to press the ÒTITLE (CONFIRM)Ó button to memorize setting. 8) The OSD shows ÒOK!Ó.
70IRE
50IRE
5-28
Samsung Electronics
Alignment and adjustment
12. B-Y Negative Gain 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to waveform monitor input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò37 CBGN XX XXÓ. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the ÒDISPLAY(DATA UP)/C.RESET (DATA DOWN)Ó button so that the yellow level is 50IRE. 7) Be sure to press the ÒTITLE (CONFIRM)Ó button to memorize setting. 8) The OSD shows ÒOK!Ó.
14. R-Y Negative Hue 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to vectorscope input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò38 CHGR XX XXÓ. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the Ò DISPLAY(DATA UP)/ C.RESET (DATA DOWN)Ó button so that the cyan vector is 284. 7) Be sure to press the ÒTITLE (CONFIRM)Ó button to memorize setting. 8) The OSD shows ÒOK!Ó.
50IRE
13. R-Y Positive Hue 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to vectorscope input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò39 CBHN XX XXÓ. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the Ò DISPLAY (DATA UP)/C.RESET (DATA DOWN)Ó button so that the red vector is 104. 7) Be sure to press the ÒTITLE (CONFIRM)Ó button to memorize setting. 8) The OSD shows ÒOK!Ó.
RED VECTOR 104 DEG.
CYAN VECTOR 284 DEG.
Samsung Electronics
5-29
Alignment and adjustment
15. B-Y Negative Hue 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to vectorscope input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MODE DOWN)Ó button so that the OSD state is Ò34 CHYE XX XXÓ. 5) Aim the camera at a color bar chart illuminated at 1500 to 2000 lx. 6) Adjust the ÒDISPLAY (DATA UP)/ C.RESET (DATA DOWN)Ó button so that the yellow vector is 165. 7) Be sure to press the ÒTITLE (CONFIRM)Ó button to memorize setting. 8) The OSD shows ÒOK!Ó.
16. B-Y Positive Hue 1) Camera ÒE-EÓ, 3100¡K color bar chart. 2) Video(output) jack and register of EEPROM. 3) Connect video(output) jack to vectorscope input jack and monitor TV jack respectively. 4) Press the ÒMENU (MODE UP)/DATE (MOD